BERGER PRODUCT SPECIFICATIONS
EPILUX 68
Epoxy Shop Primer
PRODUCT A two component epoxy polyamide shop primer pigmented with zinc phosphate rust-inhibiting
pigments.
DESCRIPTION
DESIGN As a shop primer for the protection of blast-cleaned steel against corrosion during fabrication
and assembly.
FEATURES
Extremely fast drying for easy and quick handling of coated steel.
Provides weathering and corrosion protection for up to 6 months.
Product complies with DNV : Standards for Certification 2.9
(Type Approval Programme 1-602.1) :July 1999
PHYSICAL Recommended Application Data Wet [µm] Dry [µm] m2/l
CHARACTERISTICS Theoretical Coverage 90 25 11.2
Volume solids 28 ± 2%
Dry Film Thickness Range 25 µm
Flash Point 4 °C
Finish Matt
Colour Range Red Oxide, Grey
Standard Packing Size 20 litres set (15.0 litres Base : 5.0 litres Hardener)
Mix Ratio ( by volume ) 3 Base : 1 Hardener
APPLICATION AIRLESS SPRAY Tip Size : 0.43 – 0.53 mm ( 17 – 21 thou )
Recommended method of
METHOD application
Pressure : 75 bar / 1100 psi
AIR SPRAY Recommended. Use suitable proprietary equipment.
BRUSH OR ROLLER Not recommended. However, may be used for touch-up purposes.
DRYING &
CURING TIME Ambient Touch Dry Hard Dry Full Cure Overcoating Interval Pot Life
Temperature Minimum Maximum
15 °C 5 mins. 8 mins. 7 days 10 hours Indefinite 15 hours
25 °C 4 mins. 6 mins. 7 days 5 hours Indefinite 12 hours
35 °C 3 mins. 4 mins. 7 days 3 hours Indefinite 10 hours
USEFUL THINNER : SOLVALUX 7-45 or 7-77
INFORMATION CLEANER : SOLVALUX 7-45 or 7-77
STORAGE : Store in a cool dry shaded area.
SHELF LIFE : One year minimum when stored as prescribed in the MSDS.
EPILUX 68 REVISION 06-2013
A1
BERGER PRODUCT SPECIFICATIONS
SURFACE The service life span and the service performance of EPILUX 68 is directly related to the degree
of surface preparation.
PREPARATION
STEEL
• Remove all wax, oil and grease by solvent cleaning in accordance with the guidelines given
by SSPC-SP1.
• Where necessary removes weld spatter and round off all rough weld seams and sharp
edges to a smooth surface.
• Abrasive blast clean to a minimum standard of Sa2½ (ISO 8501-1:1988) or SSPC-SP10.
• Any surface defects revealed by blast cleaning should be ground, filled or treated in a
suitable manner.
• An average surface profile of 35 - 50 microns is recommended. A rounded surface profile is
recommended. Angular abrasives may produce excessive peaks in the profile that may
protrude through the primer and lead to corrosion.
• After blasting, remove dust from the surface. The surface to be coated must also be clean
and dry.
• Apply Epilux 68 immediately after blasting to prevent oxidation and recontamination of the
steel surface. In case of oxidation or recontamination, re-blast to the required standard.
To avoid condensation of moisture onto substrate prior to coating application, relative humidity
should not exceed 85% and substrate temperature should be more than 3°C above Dew Point.
SUITABLE TOP Epilux 610, Epilux 78, Epilux 218, Epilux 58, Epilux 58HS, , Epimastic 3000HS, Epimastic 3100,
COATS Epimastic 5100, Epilux 15HS, Epilux 18HS, Epilux 155, Luxol 5000, Epilux 4, Luxathane 5075,
Luxathane 5150HS, Luxathane 5000 HB
NOTES • Product will not cure adequately at temperatures below 10 °C.
SAFETY Avoid contact with eyes and skin. Wear suitable protective clothing such as overalls, goggles,
dust mask and gloves. Use barrier cream.
PRECAUTION
This product contains low flash point solvents, do not use in poorly ventilated areas especially in
confined tank interiors.
Ensure that there is adequate ventilation in the area where the product is being applied. Do not
breathe in vapour or spray mist.
This product is flammable. Keep away from sources of ignition. Do not smoke.
Take precautionary measures against static discharge.
In case of fire, blanket flames with foam, carbon dioxide or dry chemicals.
FIRST AID Eyes : In the event of accidental splashes, flush eyes with warm water immediately
and seek medical advice.
Skin : Wash skin thoroughly with soap and water or approved industrial cleaner.
Do Not Use solvents or thinners.
Inhalation : Remove to fresh air, loosen collar and keep patient rested.
Ingestion : In case of accidental ingestion, DO NOT INDUCE VOMITING. Obtain
immediate medical attention.
For further safety information, please refer to our Material Safety Data Sheet (MSDS)
DISCLAIMER The information provided on this data sheet is not intended to be complete and is provided as general advice
only. It is the responsibility of the user to ensure that the product is suitable for the purpose for which he
wishes to use it. As we have no control over the treatment of the product, the standard of surface
preparation of the substrate, or other factors affecting the use of this product, we are not responsible for its
performance nor would we accept any liability whatsoever or howsoever arising from the use of this product
unless specifically agreed to in writing by us. The information contained in this data sheet may be modified
by us from time to time, and without notice, in the light of our experience and continuous product
development.
EPILUX 68 REVISION 06-2013
A1
