Cold milling machine W 500
Technical specification
Technical specification
Cold milling machine
W 500
Milling width max. 20” 500 mm
Milling depth *1 6” 0 – 160 mm
Milling drum
Tool spacing / ”
1 2 15 mm
Number of tools 50
Drum diameter with tools 24” 610 mm
Diameter of the milling drum 15” 385 mm
Drum inclination, max. 10 °
Engine
Manufacturer IVECO
Type 8045.SU 00
Cooling Water
Number of cylinders 4
Output 79 kW / 105 HP / 107 PS
Engine speed 2,300 min-1
Displacement 238 in3 3,900 cm3
Fuel consumption, 1/1 load 5.2 gal/h 19.7 l/h
Fuel consumption, 2/3 load 3.4 gal/h 13.0 l/h
Speed /gradeability
Operating speed, 1st gear 0 – 66 ft /min 0 – 20 m/min
Travel speed 0 – 4 MPH 0 – 6 km/h
Theoretical gradeability in 1st gear 60 %
Theoretical gradeability in travel gear 60 %
Ground clearance 8” 200 mm
Weights *2 with conveyor without conveyor
Front axle load, full tanks 5,512 lbs 2,500 daN (kg) 6,945 lbs 3,150 daN (kg)
Rear axle load, full tanks 11,023 lbs 5,000 daN (kg) 7,826 lbs 3,550 daN (kg)
Own weight 14,991 lbs 6,800 daN (kg) 13,228 lbs 6,000 daN (kg)
Operating weight, CE*3 16,094 lbs 7,300 daN (kg) 14,330 lbs 6,500 daN (kg)
Operating weight, full tanks 16,535 lbs 7,500 daN (kg) 14,771 lbs 6,700 daN (kg)
Tyres
Type Solid rubber
Tyre size, front (dia. x W) 22” x 10” 560 x 250 mm
Tyre size, rear (dia. x W) 22” x 10” 560 x 250 mm
Tank capacities
Fuel tank 43.6 gal 165 l
Hydraulic fluid tank 39.6 gal 150 l
Water tank 60.8 gal 230 l
Electrical system 24 V
Conveyor system
Belt width 16” 400 mm
Theoretical conveyor capacity 65 m3/h
Shipping dimensions
11’ 10” x 5’ 7” x 6’ 11” 11’ 10” x 5’ 7” x 6’ 11”
Dimensions of machine (L x W x H)
3,600 x 1,700 x 2,100 mm 3,600 x 1,700 x 2,100 mm
19’ 4” x 2’ 10” x 3’
Dimensions of conveyor (L x W x H) –
5,900 x 860 x 900 mm
* 1 = The maximum milling depth may deviate from the value indicated, due to tolerances and wear.
* 2 = All weights refer to basic machine without any additional equipment.
* 3 = Weight of machine with half-full water tank, half-full fuel tank, driver (75 kg) and tools.
2
Technical description
Dimensions in American standard and mm
11’9” 3580
10’7” 3220
9’6” 2890
24” 600
19’3” 5875 6’11” 2100 2
27’10” 8475
6’11” 2100
25°
2’10” 860
16” 400
15°
3’11”1185
26”
660
Basic design Suspension Steering
Compact three-wheel cold milling ma- The rear wheels are individually sus- The machine has a finger light hy-
chine with all-wheel drive, hydraulic pended. The right rear wheel can be draulic steering system.
driven milling drum and loading con- swung in front of the milling drum for
veyor system. cutting flush to curbs or along other Travel drive
obstacles. The pivotable front wheel is All three wheels are individually driven
Chassis connected to the chassis. by hydraulic motors which are fed by a
Robust welded design with fittings for common hydraulic variable displace-
individual components and parts as As an option the machine can be de- ment pump.
well as integrated fuel and water tanks. livered as 4-wheel-machine. In this
All components are easily accessible version, the single front wheel is re- The advance speeds in milling gear
for fast maintenance and repair. placed by a complete front axle. and travel gear are infinitely variable.
3
Special equipment: Version without conveyor
Dimensions in American standard and mm
11’9” 3580
6’11” 2100
6’11” 2100
20” 500 6’11” 2100 20” 500
6’11” 2100
30°
30°
4’3” 1300
4’3” 1300
3’11” 1185
5’4” 1620
5’4” 1620
2’8” 817
2’8” 817
°
°
26” 660 70
70
Brake system welded onto the drum body. Special Milling depth adjustment
Braking is achieved by drag from the edge flightings ensure a clean sharp The depth adjustment is carried out
hydrostatic transmission (closed-loop cut at the edges. For special appli- via the two adjustable support wheels
system). The hydraulic motors are in cations a variety of milling drums and which are located at the rear of the
addition fitted with an automatic cutting wheels in various widths is machine. Adjustment is carried out
springloaded brake. available. hydraulically whereby differing set-
tings permit wedge-type milling. The
Milling drum Tool changes set milling depths can be seen on
The drum is located between the rear The scraper blade can be raised and scales at the left and right hand side.
wheels and operates in an up-milling lowered hydraulically in seconds to fa-
direction. Toolholders accommodat- cilitate excellent access to the milling Conveyor
ing the round-shank cutters are drum and cutting tools. The hydraulically slewable and
4
height-adjustable conveyor accepts Soundproofing functions operate independently.
the milled material from the milling Noise levels are reduced by the stan- Filtering units are integrated into the
drum for loading into trucks. dard soundproofing which also pro- system as well as an oil cooler.
tects both the operators and the envi-
The conveyor is covered to prevent ronment against any nuisance due to Electrical system
clouds of dust being blown away by noise. 24-Volt system with 3-phase alter-
the wind and causing any nuisance. nator and two 12-Volt batteries,
Operator’s stand starter and electrical socket.
Water spray system The clearly designed operator’s stand
The integrated water spray system will at the rear of the machine is equipped Safety devices
suppress the development of dust with all controls and governing units The machine is equipped with stur-
during the milling operation, cools the which are easily accessible from the dy loading and lashing lugs for crane
milling tools and reduces wear of the driver’s seat. loading and securing the machine on
tools. low loader. A powerful horn, an eas-
Hydraulic system ily accessible EMERGENCY-OFF-
The spray nozzles can be easily The hydraulic systems for milling drum, switch as well as a complete set of
removed to facilitate cleaning. travel drive, conveyor and all governing working lights ensure safe operation.
Special equipment: 4-wheel-version
Dimensions in American standard and mm
11’9” 3580
10’7” 3220
9’6” 2890
6’11” 2100
24”600
19’3” 5875 6’11” 2100 20” 500
27’10” 8475
50°
6’11” 2100
25°
4’3”1300
13” 339
2’10” 860
5’4” 1620
2’9”
830
15°
16” 400
3’11”1185
°
70
26”
660
5
Serie Option
Equipment Cold milling
machine W 500 WIRTGEN AMERICA
Transport Wirtgen America Inc.
Loading and lashing lugs 6030 Dana Way
Illustrations are without obligation. Subject to technical changes. Performance data depend on operational conditions. – No. 09-20 AM- 07/01 © by Wirtgen GmbH 2001 Printed in Germany
Nashville, TN 37013, USA
Towing device
Road traffic licence Phone: (615) 501- 0600
Fax: (615) 501- 0691
Trailer for transporting the machine Internet: www.wirtgenamerica.com
Milling unit
Loading conveyor
Version without loading conveyor
Side mounted milling wheels
Fine milling drums
Hydraulic side plate lifters
Machine control and level control
Automatic levelling system right
Automatic levelling system left
Suspension and wheels
Machine equipped with three wheels
Machine equipped with four wheels
Miscellaneous
Comprehensive tool kit
Working lights
Warning lights
Reverse horn
Wing mirror
Soundproofing
Cyclonic precleaner for engine air filter
Integral soot filter
Hydraulic connection for additional tools
Hydraulic hammer
Special painting
Canopy roof
Operation of the cold milling machine
with biodegradeable hydraulic fluid
CE-mark
Comprehensive safety package
with Emergency-OFF switch
Safety certificate by the employer’s
liability insurance association
