SAUDIARAMCO.

NOTES:
LIST OF MATERIAL
1. ALL DIMENSIONS ARE IN MILLIMETER UNLESS
OTHERWISE SPECIFIED.
DWG. ISSUE REQ'D.

102
AMS # DESCRIPTION 2. POLES SHALL BE PRE-DRILLED WITH 20MM DIA HOLES
CODE UNIT QTY. AT LOCATIONS SPECIFIED IN THIS DRAWING.

TENSION SET 3. ALL PRE-DRILLED HOLES SHALL BE PROVIDED WITH

1 1000390097 EA 2 NE:ƒ
BOLT:STEEL MACHI N.
I x1 N.LONG.1
4 I 8, NI
350 LBS.MI MUM UTS
SHEILD WIRE OR CAPS OR PLUGS (DURABLE PLASTIC OR COMPOSITE

OF
OPGW CLEVIS: SOCKET EYE, 21MM, 15.9MM MATERIALS).
2 1000393239 EA 3

CONSENT
4. EARTHING NUT SHALL BE PROVIDED WITH BOLT AND
3 1000391984 EA 3 EYE; NUT, 3/4" SSZ. GALV.
WASHER.

5. POLE SHALL BE PERMANENTLY MARKED WITH MANU-

4 1000233194 EA 9 WASHER: SPRING: FOR ƒ IN. BOLT
FACTURERS NAME YEAR OF MANUFACTURE LEGNTH

898
1000233149 18 WASHER:ROUND,FLAT FOR ƒ N.BOLT
I AND ULTIMATE LOAD RATING.
5 EA

TTEN
6. CONTRACTOR SHALL NOT INSTALL BOTTOM LINE
6 1000387225 INSULATOR: PORCELAIN, SUSPENSION
EA 6 IN CASE OF 1-PHASE 2-WIRES+SHIELD WIRE.

WRI
(TYPICAL FOR-3) 7 1000829281 EA 1 RED LENGTH
POLE:STEEL,55FEET OR REQUI 7. POD POLE TAG MUST BE INSTALLED IN ALL POLES

BEARING THE POLE NUMBER AND INSTALLATION DATE

1000392957 1
ROD ARMOR 0.76-01 NCH DI
82 I N.LG ACSR & AWG ALU.
A.60I

THE
2 3 6 9 10 11 12 8 ST 3
8. GALVANIZED STEEL POLE MUST BE COATED WITH
9 1000390094 EA 3 NE 3/4"X 1
BOLT,MACHI TH NUT
2"LONG GALV.STEEL WI ANTI-CORROSION COATING OF COAL TAR EPOXY

THOUT
AS PER 14-SAMSS-403.
10 1000391426 EA 3 CLEVIS: INSULATOR: CLEVIS, BALL CURVED BRACKET
9. INSULATORS SHALL BE RATED ACCORDINGLY FOR
HAS 1
ON (
ON CONNECTOR FOR SUSPENSI 04N)

WI
11 CS EA 3 DI BUTI
STRI 34.5kV SYSTEM
34.5kV SYSTEM.

10. REFER TO SAES+P-107, TABLE-1 FOR CONDUCTOR &

12 1000231866 EA 8 WASHER:FOR 3/4 N.DI
I 1
A BOLT,CAD PLTD.(0-887-864)

NG
POLE CLEARANCE
POLE CLEARANCES.

DRAWI
13 1000168148 EA 2 TAG; BRASS TAG
11. EITHER COMPOSITE OR PORCELAIN TYPE INSULATORS

MAY BE USED. REFER TO SAES-P-107 FOR DETAILS.

12. FOR 55' POLE, OTHER POLE HEIGHTS, MAKE

S
THI
ADJUSTMENT ACCORDINGLY. GUY WIRES SHALL BE
1220

INSTALLED AT A TRUE ANGLE OF 45Deg. TO THE

FROM
VERTICAL. IN AREAS WHERE IS NOT FEASIBLE DUE
TO SITE CONDITIONS, A MINIMUM ANGLE OF 37 Deg
SHALL BE ADOPTED.
4 5

NED
OBTAI
127

BE
PART,SHALL
1
REFERENCE DRAWINGS

N
I
1220

FULL,OR
N
I ON
REPRODUCTI
SAUDIARAMCO.NO
GUY AND ANCHOR

OF
PROPERTY
10
NOTE

13,000 (SEE NOTE12)

SEE

SOLE
13 POLE GROUNDING

THE
ARE N
HEREI
11 12
GROUND LEVEL

NED
SCALE: NONE
PLAN

CONTAI
NTS

REVISION VALIDATION

THIS REVISION NO. 00 IS COVERED, FOR ALL APPROVAL AND CERTIFICATION

L
DETAI

CONCRETE REQUIREMENTS, PER SAEP-334, UNDER DRAWING COMPLETION CERTIFICATE NO:

ON
ANCHOR
765200-0915-001

NFORMATI
DESIGN CERTIFICATION REVIEW FOR KEY DRAWINGS OTHER
ON

(DESIGN AGENCY) REQUIRED (SAUDI ARAMCO)

POLE.

FOUNDATI

ENGG./DATE CERTIFIED BY/DATE CONST. AGENCY/DATE OPERATIONS/DATE BY/DATE

RM JAB RM JAB
09/01/15 09/01/15 09/01/15 09/01/15

REV.NO. DATE REVISION DESCRIPTION

BEARING PLATE
SEE

I
00 09/01/15 NEW STANDARD FOR STEEL POLE

THE
JOB ORDER/EWO NO.
THIS REVISION IS NOT TO BE USED FOR
765200 CONSTRUCTION UNTIL CERTIFIED AND DATED

SAUDI ARABIAN OIL COMPANY

AND
DRAWING TYPE

ARMLESS ANGLE POLE (5°-30°) STD

NG
13.8KV - 34.5KV OVERHEAD POWER LINE

DRAWI
STANDARD DRAWING

OCTAGONAL STEEL POLE STD. DWG. SAUDI ARABIA

S
PLANT NO. INDEX DRAWING NUMBER SHT. NO. REV. NO.

THI
990 P AA-036142 003 00
Saudi Aramco 2615 ENG. (05/05)

RESTRICTED VECTOR CADD-01