INSTRUCTION SHEET : IS - GF1721

STYLE NUMBER : GF1721AN,GF1721PN

6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com

PACKAGE CONTENTS ISSUED 08-2009 Revised 2009-11-19

Part Description Quantity

A Crossbar 1pc
M
B Green Ground Screw 1pc
Mounting Screws 2pcs A
C
D Lock Washer 2pcs
E Hex Nut ( for Mounting Screw ) 2pcs
F Mounting Ball 2pcs B
G Lock Ball 3pcs
H Hex Nut (1/8IP) 1pc
Flat Washer 2pcs C
I N
J Plastic Washer 2pcs
K Cap 1pc
D
L Finial 1pc
M Fixture Assembly 1pc E
N Ring 1pc
F
O Shade 1pc
P Stem Assembly 1pc G
H

K P

! WARNINGS AND CAUTIONS

WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.

CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.

PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 30 - 45 minutes
● Tools Required for Assembly (not included) : Flathead Screwdriver , Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses &4, 100 Watt, Type - A Medium Base Bulbs.
● Helpful Tools (not included) : Wire Strippers.

1 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : GF1721AN,GF1721PN

STEP 1:
a . Unfold Support Arms at 120 degree locations as shown.

Support
Arm

12
0D
eg
re
e

STEP 2:
a . Locate the holes on the Ring over the Bolts on the ends of
Support Arms. Secure by threading Lock Balls onto the
Bolts. Hand tighten until snug.
Support Arm

Bolt Socket
Assembly

Lock Ball
Ring

STEP 3: Mounting Screw

a . Screw the Mounting Screws into the Crossbar , place the Crossbar
Lock Washers over the Mounting Screws and thread the Hex Nut
Hex Nuts onto the Mounting Screws as shown . Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar .
b . Secure the Crossbar to the Outlet Box with Outlet Box
Screws . Lock Washer

Outlet Box
Outlet Box Screw

STEP 4 :
a . Locate the Ceiling Canopy onto the Crossbar and slip the
Button Stop on the end of Lanyard into the Slot on the
Crossbar as shown.
Crossbar

Button Stop
Slot
Lanyard
Ceiling
Canopy

2 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : GF1721AN,GF1721PN

STEP 5 :
* Use Wire Connectors ( not supplied ) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires .
a . Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b . Connect the House White ( or Ribbed ) Wire to the
BLACK( OR RED) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE FROM FIXTURE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet Box . GROUND WIRE GROUND WIRE
FROM HOUSE FROM FIXTURE

STEP 6 :
a . Place the Ceiling Canopy onto Outlet Box aligning 2 Outlet Box
holes in the Ceiling Canopy with 2 Mounting screws
threaded on the Crossbar and secure it against wall
with Mounting Balls . Mounting Screw

Ceiling Canopy

Mounting Ball

STEP 7 :
a . Screw the short nipple end of the Stem Assembly into the
Hex Coupling underside of the Socket Cluster. Hand
tighten until snug.

Socket Cluster
Hex Coupling

Stem Assembly

STEP 8 :
a. Pass the following components over the end of the Stem
Assembly in turn:
Flat Washer, Plastic Washer, Shade, Plastic Washer and
Flat Washer.
b. Thread the Hex Nut onto the end of the Stem Assembly and
Stem Assembly
tighten gently until snug to secure the above parts
together.
Flat Washer
Plastic Washer

Plastic Washer Shade

Flat Washer
Hex Nut

3 OF 4
INSTALLATION INSTRUCTIONS STYLE NUMBER : GF1721AN,GF1721PN

STEP 9 :
a. Pass the Cap over the end of the Stem and secure with the
Finial. Hand tighten until snug.

Stem
Cap

Finial

STEP 10 :
a . Install correct bulbs referring to fixture markings and / or labels for maximum wattage .

Your installation is completed now . Restore electricity . Retain this sheet for future reference .

4 OF 4