INSTRUCTION SHEET IS-SPH1716
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com
STYLE NUMBER: SPH1716PN
PACKAGE CONTENTS ISSUED 08-2010 REVISED 2010-08-20
PART DESCRIPTION QUANTITY
A Crossbar 1 pc
B Green Ground Screw 1 pc A
C Mounting Screw 2 pcs
K
D Small Lock Washer 2 pcs B
E Small Hex Nut 2 pcs
F Mounting Ball 2 pcs C
G 1/8 IP Hex Nut 1 pc
H Small Cap 1 pc
D
I Big Cap 1 pc L
E
J Finial 1 pc
F
K Socket Assembly 1 pc
G
L Center Stem Assembly 1 pc
H
M Shade 1 pc
M
I
WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by switching
off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before the
installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure that bulb(s) had sufficient
time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package contents
list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or operate the
product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● Tool Required for Assembly (not included): Flathead screwdriver, Phillips screwdriver, Pliers, Electrical tape,
Wire cutter, Safety glasses and (2) 100W A19 medium base bulbs .
● Helpful Tools (not included): Wire strippers.
1 OF 3
INSTALLATION INSTRUCTIONS STYLE NUMBER: SPH1716PN
STEP 1:
a. Screw the Mounting Screws into the Crossbar, place Mounting Screw
Crossbar
the Lock Washers over the Mounting Screws and
thread the Hex Nuts onto the Mounting Screws as Hex Nut
shown. Secure the position of the Mounting Screws by
tightening the Hex Nuts against the Crossbar.
b. Secure the Crossbar to the Outlet Box with Outlet Box
Screws.
Lock Washer
Outlet Box
Outlet Box Screw
STEP 2:
Use Wire Connectors (not supplied) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires.
a. Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b. Connect the House White (or Ribbed) Wire to the
Fixture Supply Wire (Black or Smooth Side). BLACK (OR RED) WIRE BLACK OR SMOOTH
c. Connect the House Black (or Red) Wire to the Fixture FROM FIXTURE
FROM HOUSE
Supply Wire (Black or Smooth Side).
d. Wrap each connection with approved electrical tape
and carefully stuff all of the connected wires into the GROUND WIRE GROUND WIRE
Outlet Box.
FROM HOUSE FROM FIXTURE
STEP 3:
a. Place the Ceiling Canopy over the Mounting Screws
and secure with Mounting Balls. Hand-tighten until Outlet Box
snug .
Mounting Screw
Ceiling Canopy
Mounting Ball
2 OF 3
INSTALLATION INSTRUCTIONS STYLE NUMBER: SPH1716PN
STEP 4:
a. Screw the top end of the Center Stem Assembly into the
hex coupling underside of the Socket Cluster as shown.
Hand-tighten until snug.
Socket Cluster
Hex Coupling
Center Stem Assembly
STEP 5:
a. Locate the Shade and the Small Cap over the end of
the Center Stem Assembly in turn. Secure by threading
the 1/8 IP Hex Nut onto the Center Stem Assembly.
Tighten until snug.
b. Place the Big Cap over the end of the Center Stem
Assembly and secure with the Finial. Hand-tighten until
snug.
Center Stem
Assembly
Shade
Small Cap
1/8 IP Hex Nut
Big Cap
Finial
STEP 6:
a. Install correct bulbs referring to fixture markings and/or labels for maximum wattage.
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
3 OF 3
