INSTRUCTION SHEET : IS - JO8310
STYLE NUMBER : JO8310IB
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
www . quoizel . com
PACKAGE CONTENTS ISSUED 09-2009 Revised 2009-11-26
Part Description Quantity
A Crossbar 1pc
B Green Ground Screw 1pc
Mounting Screws 2pcs A
C
D Lock Washer 2pcs
E Hex Nut 2pcs
F Mounting Ball 2pcs B
G Fixture Body 1pc
H Glass Panel 4pcs
C
G
! WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTION:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time : 20 - 30 minutes
● Tools Required for Assembly (not included) : Flathead Screwdriver , Phillips Screwdriver, Pliers,
Electrical Tape, Wire Cutters, Safety Glasses & 1, 150 Watt, Type - A Medium Base Bulb.
● Helpful Tools (not included) : Wire Strippers.
1 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : JO8310IB
STEP 1 :
a . Take apart the Fixture Hood from the Cage by unscrewing
the Lock Screws.
Fixture
Hood
Lock Screw
Cage
STEP 2 :
a . Place the Glass Panel inside of the Cage as shown.
Locate the bottom of the Glass Panel into the Slot in the
bottom of the Cage. Secure the Glass Panel by folding the Glass Panel
Tabs on the top edge of the Cage onto the top end of the
Glass Panel.
b. Repeat this process to complete all Glass Panels.
Cage
Tab
Glass
Panel
Cage
Slot
2 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : JO8310IB
STEP 3 :
a . Install the correct bulb referring to fixture markings and / or labels for maximum wattage .
STEP 4 : Mounting Screw
a . Locate the Fixture Hood onto the top edge of the Cage.
Fixture
Secure by threading the Lock Screws into the mounting Hood
holes in the bottom of the Fixture Hood. Tighten until snug.
Lock Screw
Cage
STEP 5: Mounting Screw
a . Screw the Mounting Screws into the Crossbar , place the Crossbar
Lock Washers over the Mounting Screws and thread the Hex Nut
Hex Nuts onto the Mounting Screws as shown . Secure the
position of the Mounting Screws by tightening the Hex Nuts
against the Crossbar .
b . Secure the Crossbar to the Outlet Box with Outlet Box
Screws . Lock Washer
Outlet Box
Outlet Box Screw
STEP 6 :
Backplate
a . Locate the Backplate onto the Crossbar and slip the Button
Stop on the end of Lanyard into the Slot on the Crossbar as Crossbar
shown.
Button Stop
Lanyard
Slot
3 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : JO8310IB
STEP 7 :
* Use Wire Connectors ( not supplied ) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires .
a . Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b . Connect the House White ( or Ribbed ) Wire to the
BLACK ( OR RED ) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE FROM FIXTURE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet GROUND WIRE GROUND WIRE
Box . FROM HOUSE FROM FIXTURE
STEP 8 : Mounting
a . Place the Backplate over the Mounting Screws and secure Screw
with Mounting Balls. Hand tighten until snug.
Mounting Ball
Backplate
STEP 9 :
a . Refer to following information for caulking instructions :
For assemble the MOUNTING BALLS , please note that
you are required to apply a small amount of Silicone
sealer to the threaded side of the MOUNTING BALLS
and then install them onto the MOUNTING SCREWS .
EXTERIOR GRADE
CAULK
MOUNTING BALL
4 OF 5
INSTALLATION INSTRUCTIONS STYLE NUMBER : JO8310IB
With the OUTDOOR FIXTURE properly installed in accordance with supplied Assembly/installation
instructions, proceed with caulking instructions below.
Note: Be sure EXTERIOR WALL SURFACE and FIXTURE BACKPLATE are free to dirt to caulking.
Using EXTERIOR GRADE CAULK, start on one side of FIXTURE BACKPLATE and follow contour, were
the FIXTURE BACKPLATE meets the EXTERIOR WALL SURFACE upward. Proceed to caulk over top of
backplate and down other side. DO NOT CAULK BOTTOM OF FIXTURE BACKPLATE to ensure proper
moisture drainage.
EXTERIOR GRADE
CAULK
OUTDOOR
FIXTURE BACKPLATE
EXTERIOR WALL SURFACE
Your installation is completed now. Restore electricity. Retain this sheet for future reference.
5 OF 5
