INSTRUCTION SHEET IS - DV9011
6 CORPORATE PARKWAY
GOOSE CREEK , SC . 29445
STYLE NUMBER : DV9011HS,DV9011BA
www . quoizel . com
PACKAGE CONTENTS ISSUED 02-2010
Part Description Quantity
A Fixture Hood 1pc C
B Cage 1pc
C Lock Screw 2pcs D
A
D Mounting Ball 2pcs
E
E Mounting Screw 3pcs
F Hanger 1pc
G Glass Panel 4pcs F
! WARNINGS AND CAUTIONS
WARNING:
● Before beginning the installation, turn off electricity at the circuit breaker box or the main fuse box by
switching off the circuit breaker or removing the fuse.
CAUTIONS:
● These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture. We strongly recommend that a professional electrician install the fixture.
● Disconnect fixture from the power source before replacing the bulb(s), making sure the bulb(s) had
sufficient time to cool down. DO NOT subject the lamp to any shock while lit as shattering of lamp may
result.
PREPARATION
● Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
● Estimated Assembly Time: 20 - 30 minutes
● Tools Required for Assembly (not included): Flathead screwdriver , Phillips screwdriver, pliers, electrical
tape, wire cutters, safety glasses & 1, 150 Watt, A21 Medium Base Bulb.
● Helpful Tools (not included): Wire Strippers.
1 OF 3
INSTALLATION INSTRUCTIONS STYLE NUMBER : DV9011HS, DV9011BA
STEP 1 :
a. Slip the Glass Panel inside of the Slot in the bottom of the
Cage. Attach the Glass Panel onto the Cage. Secure by Glass Panel
folding the Tab from location “A” to location “B”.
Cage
A
Tab
B
Glass
Panel
Cage
STEP 2:
a . Install the correct bulb referring to fixture markings and / or labels for maximum wattage .
STEP 3 :
a . Attach the Hanger onto the top end of the Fixture Hood.
Line up holes on it and mounting holes on the Fixture Hanger
Hood. Secure by threading the Lock Screw into the
mounting hole. Hand-tighten until snug. Lock Screw
Fixture
Hood
2 OF 3
INSTALLATION INSTRUCTIONS STYLE NUMBER : DV9011HS, DV9011BA
STEP 4 :
a . Pass the Bolts in the bottom of the Fixture Hood through
the holes on the top edge of the Cage. Secure by threading
the Mounting Balls onto the Bolts. Hand-tighten until snug.
Fixture Hood
Bolt
Mounting
Ball
Cage with
Glass Panels
STEP 5 :
a. Carefully fit the Post Fitter over the end of the Post
( not supplied ), making sure the Post Fitter is fully
seated .
b . Mark the drill point for the ( 3 ) Mounting Screws , using
( 3 ) Mounting Holes as reference . After marking hole
locations , remove Fixture from Post and drill 1 / 16 " pilot Post Fitter
holes for screws .
c . Refer to Step 5 for wire connections . Mounting Screw
d . Coat the top 1 " of the Post with Clear Silicone Caulk
( not supplied ) and position the Post Fitter onto the
Post . Be sure to seat it completely , aligning the holes
in the Fitter with the 1 / 16 " Pilot Holes drilled into the
Post ( not supplied )
Post .
e . Secure the Fixture to Post with ( 3 ) Mounting Screws .
STEP 6 :
* Use Wire Connectors ( not supplied ) to connect the
WHITE OR RIBBED WHITE OR RIBBED
wires .
a . Connect the House Ground Wire to the Fixture Ground FROM HOUSE FROM FIXTURE
Wire.
b . Connect the House White ( or Ribbed ) Wire to the
BLACK ( OR RED ) WIRE BLACK OR SMOOTH
Fixture Supply Wire ( White or Ribbed Side ) .
c . Connect the House Black ( or Red ) Wire to the Fixture FROM HOUSE FROM FIXTURE
Supply Wire ( Black or Smooth Side ).
d . Wrap each connection with approved electrical tape and
carefully stuff all of the connected wires into the Outlet GROUND WIRE GROUND WIRE
Box . FROM HOUSE FROM FIXTURE
Your installation is completed now . Restore electricity . Retain this sheet for future reference .
3 OF 3
