VHDL Transmitter (UART_TX.
vhd):
//////////////////////////////////////////////////////////////////////
// File Downloaded from http://www.nandland.com
//////////////////////////////////////////////////////////////////////
// This file contains the UART Receiver. This receiver is able to
// receive 8 bits of serial data, one start bit, one stop bit,
// and no parity bit. When receive is complete o_rx_dv will be
// driven high for one clock cycle.
//
// Set Parameter CLKS_PER_BIT as follows:
// CLKS_PER_BIT = (Frequency of i_Clock)/(Frequency of UART)
// Example: 10 MHz Clock, 115200 baud UART
// (10000000)/(115200) = 87
module uart_rx
#(parameter CLKS_PER_BIT)
(
input i_Clock,
input i_Rx_Serial,
output o_Rx_DV,
output [7:0] o_Rx_Byte
);
parameter s_IDLE = 3'b000;
parameter s_RX_START_BIT = 3'b001;
parameter s_RX_DATA_BITS = 3'b010;
parameter s_RX_STOP_BIT = 3'b011;
parameter s_CLEANUP = 3'b100;
reg r_Rx_Data_R = 1'b1;
reg r_Rx_Data = 1'b1;
reg [7:0] r_Clock_Count = 0;
reg [2:0] r_Bit_Index = 0; //8 bits total
reg [7:0] r_Rx_Byte = 0;
reg r_Rx_DV = 0;
reg [2:0] r_SM_Main = 0;
// Purpose: Double-register the incoming data.
// This allows it to be used in the UART RX Clock Domain.
// (It removes problems caused by metastability)
always @(posedge i_Clock)
begin
r_Rx_Data_R <= i_Rx_Serial;
r_Rx_Data <= r_Rx_Data_R;
end
// Purpose: Control RX state machine
always @(posedge i_Clock)
begin
case (r_SM_Main)
s_IDLE :
begin
r_Rx_DV <= 1'b0;
r_Clock_Count <= 0;
r_Bit_Index <= 0;
if (r_Rx_Data == 1'b0) // Start bit detected
r_SM_Main <= s_RX_START_BIT;
else
r_SM_Main <= s_IDLE;
end
// Check middle of start bit to make sure it's still low
s_RX_START_BIT :
begin
if (r_Clock_Count == (CLKS_PER_BIT-1)/2)
begin
if (r_Rx_Data == 1'b0)
begin
r_Clock_Count <= 0; // reset counter, found the middle
r_SM_Main <= s_RX_DATA_BITS;
end
else
r_SM_Main <= s_IDLE;
end
else
begin
r_Clock_Count <= r_Clock_Count + 1;
r_SM_Main <= s_RX_START_BIT;
end
end // case: s_RX_START_BIT
// Wait CLKS_PER_BIT-1 clock cycles to sample serial data
s_RX_DATA_BITS :
begin
if (r_Clock_Count < CLKS_PER_BIT-1)
begin
r_Clock_Count <= r_Clock_Count + 1;
r_SM_Main <= s_RX_DATA_BITS;
end
else
begin
r_Clock_Count <= 0;
r_Rx_Byte[r_Bit_Index] <= r_Rx_Data;
// Check if we have received all bits
if (r_Bit_Index < 7)
begin
r_Bit_Index <= r_Bit_Index + 1;
r_SM_Main <= s_RX_DATA_BITS;
end
else
begin
r_Bit_Index <= 0;
r_SM_Main <= s_RX_STOP_BIT;
end
end
end // case: s_RX_DATA_BITS
// Receive Stop bit. Stop bit = 1
s_RX_STOP_BIT :
begin
// Wait CLKS_PER_BIT-1 clock cycles for Stop bit to finish
if (r_Clock_Count < CLKS_PER_BIT-1)
begin
r_Clock_Count <= r_Clock_Count + 1;
r_SM_Main <= s_RX_STOP_BIT;
end
else
begin
r_Rx_DV <= 1'b1;
r_Clock_Count <= 0;
r_SM_Main <= s_CLEANUP;
end
end // case: s_RX_STOP_BIT
// Stay here 1 clock
s_CLEANUP :
begin
r_SM_Main <= s_IDLE;
r_Rx_DV <= 1'b0;
end
default :
r_SM_Main <= s_IDLE;
endcase
end
assign o_Rx_DV = r_Rx_DV;
assign o_Rx_Byte = r_Rx_Byte;
endmodule // uart_rx
