HomeWorks QS LQSE-2DAL-D DALI Power Module

369650e 1 03.06.18

DALI Power Module

The DALI Power Module is a DIN-rail mounted
controller for DALI-compliant digital addressable
loads, referred to as control gear. It provides DALI
bus power and control for two independent DALI
buses with up to 64 DALI-compliant digital

COM
DA 1 DA 2

MUX
MUX
Assembled in Mexico
Assemblé aux Mexique NEC® Class 2 NEC®
Ensamblado en México IEC PELV Class 2

HomeWorks QS
addressable loads each. Ta > 65 ºC LQSE-2DAL-D
120 V~ 50 / 60 Hz 120 mA +1.844.LUTRON1
Model Number
243C IND.CONT.EQ.
Test | Prueba
Tester 230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657
lutron.com

LQSE-2DAL-D: 2-link DALI fixture controller L N Ta ≤ 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

Features
• Provides power for two buses of DALI-compliant
digital addressable loads:
DALI Power Module (LQSE-2DAL-D)
–1
 28 mA guaranteed current
–2
 50 mA maximum supply current per bus
• Each DALI bus can control a maximum of
16 zones.
• Power failure memory retains programming in
the event of a power loss.
• DALI Power Module can be used in a
HomeWorks QS system to control and manage light
in an entire home or building.

DALI bus 1 Up to 64
DALI-compliant
digital
Control gear Control gear
DALI bus 2 addressable
loads on each
Control gear Control gear
bus

HomeWorks QS GRAFIK
Wallstation Power Eye QS
Module
EEA contact address: This device complies with part 15 of the FCC Rules. Operation is

HomeWorks QS
50017652a

IBRA subject to the following two conditions: (1) This device may not cause
50
Lutron EA Limited
TION
CAL

125 Finsbury Pavement, 4th floor interference. (2) This device must accept any interference, including
interference that may cause undesired operation.
London EC2A 1NQ P OI N T CAN ICES-3 (B)/NMB-3(B) www.lutron.com/ChinaRohs
United Kingdom (Importer)

120 / 230 V~ Processor
800 W Max 500 W Max 500 W Max 500 W Max

CCI
Zone 1 Zone 2 Zone 3 Zone 4

Option
DIN Rail Power Module

Input Def H
LQSE-4A-D

Hi Temp Opt1 M

Prog Opt2 L
COM

DA 1 DA 2
MUX
MUX

Assembled in Mexico Power Opt3

Assemblé aux Mexique NEC® Class 2 NEC® 230 V~ 50 / 60 Hz 10 A www.lutron.com +44.(0)20.7702.0657

Ensamblado en México IEC PELV Class 2

Control Power Up to 100

HomeWorks QS
Ta > 65 ºC LQSE-2DAL-D
Test | Prueba 120 V~ 50 / 60 Hz 120 mA 243C IND.CONT.EQ. +1.844.LUTRON1
Tester 230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657

total QS
lutron.com
L N Ta ≤ 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

QS Link QS
devices

7
Contact
Closure
DALI Interface
Power Module
Sivoia QS
Shade / Drapery QS
Power
Supply

® S P E C I F I C AT I O N S U B M I T TA L Page 1
Job Name: Model Numbers:

Job Number:
 HomeWorks QS LQSE-2DAL-D DALI Power Module
369650e 2 03.06.18

Specifications
Power Programming and Compatibility Requirements
• 120 V~ 50/60 Hz 120 mA • The LQSE-2DAL-D can only be used with the
• 230 V~ 50/60 Hz 80 mA HomeWorks QS system.
• Lightning strike protection meets ANSI/IEEE standard • Setup and programming of the DALI Power Module
62.31-1980. Can withstand voltage surges of up to is done through the HomeWorks QS programming
6000 V~ and current surges of up to 3000 A. software.
• Stand by power: 7 W DALI Buses
• BTUs / hour when fully loaded: 24 • Up to 64 DALI compliant loads on each bus can be
• DALI bus Output: 16 V- 128 mA guaranteed supply addressed and grouped into 16 zones.
current, 250 mA maximum supply current per bus. • DALI Power Module supplies a maximum of 250 mA
Standards to power each bus.
• Lutron Quality Systems registered to ISO 9001:2015. • DALI Power Module supplies a guaranteed current
• IEC 60669-2-1 of 128 mA to power each bus.
• DALI-2 Certified • DALI Power Module has an integrated bus power
• UL supply with polarity indicated on the unit.
• cUL • Some DALI loads may be polarity sensitive. Refer to
• NOM individual manufacturers' specifications for proper
connection to the DALI bus.
DALI Control Gear Compatibility • Short circuit protection with automatic restart.
• DALI-2 Certified; Compatible with DALI control gear
(e.g. LED drivers). QS Link Limits
• The LQSE-2DAL-D is a single master controller and • A QS link in a HomeWorks QS system can have
therefore no other controllers may exist on the same up to 512 zones (outputs) and 100 devices. A DALI
DALI bus. compliant digital addressable load counts as 1 zone
unless specifically grouped into zones from the
Environment HomeWorks QS software.
• Surrounding Air Temperature Range: 0 ºC to 65 ºC • Each DALI Power Module counts as one device
(32 ºF to 149 ºF). toward the 100 device limit.
• Relative Humidity: less than 90% non-condensing.
• A maximum of 8 fully loaded DALI buses may be
• Calibration point maximum: 75 ºC (167 ºF) connected to a single QS link.
• For indoor use only.
HomeWorks QS Wallstations
Terminals
• HomeWorks QS wallstations can be configured to
• Mains Wiring: 1.0 mm2 to 4.0 mm2 control DALI Power Modules with the HomeWorks QS
(18 AWG to 10 AWG) programming utility.
• DALI bus Wiring: 0.5 mm2 to 4.0 mm2 • LED indicator displays the status of programmed lights.
(20 AWG to 10 AWG)
• QS Link Wiring: 0.5 mm2 to 4.0 mm2
(20 AWG to 10 AWG) Troubleshooting and Maintenance
• Minimum wire temperature rating = 65 °C (149 ºF), Features
copper wire only • Maintains redundant memory of control gear
programming for ease of single or multiple control
Mounting gear replacement.
• Mount in a Lutron DIN Panel (see spec 369788) or in • To verify DALI lights connected to DALI bus 1 and
an IP20 (minimum) rated consumer panel or breaker bus 2:
panel with integrated DIN rail.
• Width = 9 DIN modules (161.7 mm or 6 3⁄8 in). – Enter Test Mode: Press and hold Test button on
the DALI Power Module until the Test LED starts
• For more information on mounting and installation in flashing.
panels with integrated DIN rail see Lutron P/N 048466
at www.lutron.com. – Test: Each press of either the DALI 1 or DALI 2
button will cycle the lights between high-end,
low-end, flash and off for that bus.
– Exit Test Mode: Press and hold Test button until
® S P E C I F I C AT I O N S U B M I T TA L Test LED stops flashing. Page 2
Job Name: Model Numbers:

Job Number:
 HomeWorks QS LQSE-2DAL-D DALI Power Module
369650e 3 03.06.18

Overview of Wiring Terminals and Mechanical Dimensions

IEC PELV / NEC®
Class 2 NECR Class 2
QS DALI DALI
Link bus 1* bus 2*
500-13431 Rev. B

Z096
N1771

COM

DA 1 DA 2
MUX
MUX

Assembled in Mexico
Assemblé aux Mexique NEC® Class 2 NEC®
Ensamblado en México IEC PELV Class 2

HomeWorks QS 89.7 mm
Ta > 65 ºC LQSE-2DAL-D (3 1⁄2 in)
Test | Prueba 120 V~ 50 / 60 Hz 120 mA 243C IND.CONT.EQ. +1.844.LUTRON1
Tester 230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657
lutron.com
L N Ta ≤ 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

161.7 mm
Mains (6 3⁄8 in)
Wiring

* Wire according to local codes.

60.6 mm
(2 3⁄8 in)

® S P E C I F I C AT I O N S U B M I T TA L Page 3
Job Name: Model Numbers:

Job Number:
 HomeWorks QS LQSE-2DAL-D DALI Power Module
369650e 4 03.06.18

Wiring: Mains Voltage

Wiring from Distribution to Power Module

• Turn off all circuit breakers or isolators feeding the
Power Module unit at the distribution panel.
COM

DA 1 DA 2
MUX
MUX

Assembled in Mexico
Assemblé aux Mexique NEC® Class 2 NEC®
Ensamblado en México IEC PELV Class 2

Ta > 65 ºC
HomeWorks QS
LQSE-2DAL-D • Run line, neutral, and earth/ground (D) wires from a
feed to the DALI Power Module.
Test | Prueba 120 V~ 50 / 60 Hz 120 mA 243C IND.CONT.EQ. +1.844.LUTRON1
Tester 230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657
lutron.com
L N Ta ≤ 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

•NEC 1.02 mm2 to 4.0 mm2 (18 AWG

UseClass DA 1 toDA
12 AWG)

COM
2

MUX
MUX
Assembled in Mexico
Assemblé aux Mexique ® NEC®
Ensamblado en México
conductors (depending on breaker rating) to
IEC PELV
feed the
Class 2

HomeWorks QS mains wiring. The device draws less than 120 mA

Ta > 65 ºC LQSE-2DAL-D (120 V~) and 80 mA (230 V~).
Test | Prueba 120 V~ 50 / 60 Hz 120 mA 243C IND.CONT.EQ. +1.844.LUTRON1
Tester
Emergency Lighting Applications
230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657
lutron.com • Use normal (non-essential) power only to power the
L N Ta ≤ 65 °C 65/75 ºC Cu Al DALI Power Module.
5 in-lb (0,6 N•m) 5/16 in (8 mm)
• When normal power drops out, the DALI Power Module
will not power the DALI buses. When this occurs,
control gear powered from emergency feeds go to their
emergency mode (full light output by default).
Mains Wiring and IEC PELV / NEC® Class 2
Separation
• The DALI Power Module is designed to separate mains
wiring from IEC PELV / NEC® Class 2 circuits.
N • Follow appropriate local and national codes to avoid
violating required separation guidelines.
L

Distribution
Panel

– Earth/Ground
N – Neutral
L – Mains/Line

® S P E C I F I C AT I O N S U B M I T TA L Page 4
Job Name: Model Numbers:

Job Number:
 HomeWorks QS LQSE-2DAL-D DALI Power Module
369650e 5 03.06.18

Wiring: DALI Bus

The DALI Power Module will supply power for two

independent DALI buses, which supports a maximum
of 64 DALI-compliant digital addressable loads per
bus.
COM

DA 1 DA 2
MUX
MUX

Assembled in Mexico
Assemblé aux Mexique NEC® Class 2 NEC®
Ensamblado en México IEC PELV Class 2

HomeWorks QS
Ta > 65 ºC LQSE-2DAL-D
Test | Prueba
Tester
120 V~ 50 / 60 Hz 120 mA
230 V~ 50 / 60 Hz 80 mA
lutron.com
243C IND.CONT.EQ. +1.844.LUTRON1
+44.(0)20.7702.0657 DALI Wiring
• DALI wiring is not SELV.
L N Ta ≤ 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

• DALI wiring may be treated as mains voltage, and thus

can be run within the same sheathing.
• Ensure that there is no greater than a 2 V ~ drop
DALI DALI between the DALI Power Module and the end of the
bus 1 bus 2 DALI bus.
DALI 1 DALI 2 • Consult all national and local electrical codes for
separation requirements.
DALI 1 DALI 2

Maximum DALI-compliant
Wire Gauge Bus Wire Length
1.5 mm2 (14 AWG) 300 m (984 ft)

0.75 mm2 (18 AWG) 150 m (492 ft)

0.5 mm2 (20 AWG) 100 m (328 ft)

DA 1 DA 2
NEC®
Class 2

Lutron Qualified DALI Control Gear

NT.EQ. +1.844.LUTRON1
Lutron requires that all DALI devices that are intended to be used with a Lutron DALI controller must be
+44.(0)20.7702.0657
pre-tested by Lutron and determined to be compatible before being used on a project.
b (0,6 N•m)For a complete
5/16 in (8 mm)list of Lutron qualified DALI ballasts please refer to Application Note #482 for more information.

® S P E C I F I C AT I O N S U B M I T TA L Page 5
Job Name: Model Numbers:

Job Number:
 HomeWorks QS LQSE-2DAL-D DALI Power Module
369650e 6 03.06.18

Wiring: QS Link

IEC PELV / NEC® Class 2 QS Link Wiring

• Link communicates using IEC PELV / NEC®
Class 2 wiring.
COM

DA 1 DA 2
MUX
MUX

Assembled in Mexico
Assemblé aux Mexique NEC® Class 2 NEC®
Ensamblado en México IEC PELV Class 2

• Follow all applicable national and local codes for

HomeWorks QS
Ta > 65 ºC LQSE-2DAL-D
Test | Prueba 120 V~ 50 / 60 Hz 120 mA 243C IND.CONT.EQ. +1.844.LUTRON1

proper circuit separation and protection.

Tester 230 V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657
lutron.com
L N Ta ≤ 65 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

• Wiring may be daisy chained or t-tapped.

• Do NOT connect terminal 2.
• Total length of QS link must not exceed 610 m
(2000 ft).
• Use one, twisted-shielded pair of 0.5 mm2 (20 AWG)
for data link (MUX, _).
QS Link Available from
Wiring Length Wire Gauge Lutron in one cable:
Power (terminals 1 and 2):
1 pair 1.0 mm2 (18 AWG) GRX-CBL-346S
Less than (non plenum)
153 m (500 ft) Data (terminals 3 and 4): GRX-PCBL-346S
1 pair 0.5 mm2 (20 AWG), (plenum)
twisted and shielded
Power (terminals 1 and 2): GRX-CBL-46L
153 m to 1 pair 4.0 mm2 (10 AWG) (non plenum)
610 m Data (terminals 3 and 4): GRX-PCBL-46L
(1) COM (500 to 2000 ft) 1 pair 0.5 mm2 (20 AWG), (plenum)
COM

DA 1 andDA 2
MUX
MUX

twisted shielded
(2) ® Class
NEC No2Connection NEC®
IEC PELV Class 2
(3) MUX
meWorks QS (4) MUX

SE-2DAL-D
~ 50 / 60 Hz 120 mA 243C IND.CONT.EQ. +1.844.LUTRON1
V~ 50 / 60 Hz 80 mA +44.(0)20.7702.0657
lutron.com
5 °C 65/75 ºC Cu Al 5 in-lb (0,6 N•m) 5/16 in (8 mm)

)Lutron, Lutron, HomeWorks, Sivoia, and GRAFIK Eye are trademarks of Lutron Electronics Co., Inc., registered in the U.S. and other countries.

NEC is a registered trademark of the National Fire Protection Association, Quincy, Massachusetts

® S P E C I F I C AT I O N S U B M I T TA L Page 6
Job Name: Model Numbers:

Job Number: