MICRO PRECISION CALIBRATION CO.
, LTD VIETNAM DIVISION (ĐK 280)
NO 201, 2 FLOOR, SACOM CHIPSANG BUILDING, LOT T2-4, D1 STREET,
SAIGON HIGH TECH PARK
DISTRICT 9, HCMC VIETNAM
84 5448 2008
Certificate of Calibration
AC-1969.22
Date: October 31, 2020 Cert No. 551220083909995
Customer:
CENTRAL PHARMACEUTICAL I JSC - PHARBACO
THACH LOI, THANH XUAN, SOC SON,
HA NOI VIET NAM HA NOI
Work Order #: VN-18024565
MPC Control #: 036R7G3DA1 Serial Number: 036R7G3DA1
Asset ID: N/A Department: N/A
Gage Type: AIR VELOCITY TRANSMITTER Performed By: CHAU NGUYEN
Manufacturer: DWYER Received Condition: IN TOLERANCE
Model Number: AVUL-3DA1-LCD Returned Condition: IN TOLERANCE
Size: (0 to 20) m/s Cal. Date: October 31, 2020
N/A12 MONTHS
Temp/RH: 21.2°C / 52 % Cal. Interval: 12 MONTHS
N/A
Location: Calibration performed at MPC facility Cal. Due Date: October 31, 2021
N/A
Calibration Notes:
Please refer to the attached Calibration Report (1 pages)
Standards Used to Calibrate Equipment
I.D. Description. Model Serial Manufacturer Cal. Due Date Traceability #
CN2821 THERMO-ANEMOMETER MVT Z040945 DWYER INSTRUMENTS Aug 10, 2021 551220083781820
INC.
CA3495 WIND TUNNEL WTM-1000 181014 OMEGA Jun 4, 2021 551220083133117
CN1884 DIGITAL MULTIMETER 34401A US36125843 AGILENT Jun 10, 2021 551220083636786
Procedures Used in this Event
Procedure Name Description
MPC-AIR-001 Rev. 01 Air Velocity, Temperature and Flow Meters, General, rev01, Feb-11-2020
Calibrating Technician: QC Approval:
CHAU NGUYEN DO THE HOANG AN
STATEMENTS OF PASS OR FAIL CONFORMANCE: The uncertainty of measurement has been taken into account when determining compliance with specification. All measurements and test results guard banded to ensure the
probability of false-accept does not exceed 2% in compliance with ANSI/NCSL Z540.3-2006 and in case without guard banded the probability of false-accept depending on test uncertainty ratio.
THE CALIBRATION REPORT STATUS:
PASS- Term used when compliance statement is given, and the measurement result is PASS.
PASSz - Term used when compliance statement is given, and the measurement result is conditional passed or PASSz .
FAIL- Term used when compliance statement is given, and the measurement result is FAIL.
FAILz - Term used when compliance statement is given, and the measurement result is conditional failed or FAIL z .
REPORT OF VALUE - Term used when reported measurement is not requiring compliance statement in report.
ADJUSTED- When adjustments are made to an instrument which changes the value of measurement from what was measured as found to new value as left.
LIMITED - When an instrument fails calibration but is still functional in a limited manner.
The expanded uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%, unless otherwise stated. This
calibration report complies with ISO/IEC 17025:2017 and ANSI/NCSL Z540.3. Calibration cycles and resulting due dates were submitted/approved by the customer. Any number of factors may cause an instrument to drift out of tolerance before the next
scheduled calibration. Recalibration cycles should be based on frequency of use, environmental conditions and customer's established systematic accuracy. All standards are traceable to SI through the National Institute of Standards and Technology (NIST)
and/or recognized national or international standards laboratories. Services rendered include proper manufacturer’s service instruction and are warranted for no less than thirty (30) days. The information on this report pertains only to the instrument identified,
this may not be reproduced in part or in a whole without the prior written approval of the issuing MP Calibration Laboratory.
Page 1 of 1 (CERT, Rev 7)
