40–1

AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

AUTOMATIC TRANSAXLE ASSY (U34#E Series)

4002G–01

OVERHAUL
1. REMOVE SPEEDOMETER (ATM) SENSOR
[ 83181E / 3505 ]
2. REMOVE SPEEDOMETER DRIVEN (ATM) GEAR SUB–ASSY
[ 33403G / 3505 ]

3. REMOVE NEUTRAL START SWITCH ASSY

[ 84540G / 3513 ]
(a) Remove the nut, washer and control lever.
(b) Using a screwdriver, unstake the lock nut and remove the
lock washer and lock nut.
(c) Remove the 2 bolts and pull out the neutral position
switch.

C81327

4. REMOVE TRANSMISSION REVOLUTION SENSOR

[ 89413E / 3512 ]
(a) Remove the bolt and transaxle revolution sensor.

C67751

5. REMOVE OIL COOLER TUBE UNION(OUTLET OIL

COOLER UNION)
[ 32921C / 3514 ]
(a) Remove the oil cooler tube union.
(b) Remove the O–ring from the oil cooler tube union.

D25286

6. REMOVE OIL COOLER TUBE UNION(INLET OIL

COOLER UNION)
[ 32921C / 3514 ]
(a) Remove the oil cooler tube union.
(b) Remove the O–ring from the oil cooler tube union.

C80725

U340E A/T REPAIR MANUAL (RM824E)

40–2
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

7. REMOVE TRANSAXLE CASE NO.1 PLUG

[ 35104Q / 3503 ]
(a) Remove the 4 transaxle case No.1 plugs from the trans-
axle housing and transaxle case.

C67754

(b) Remove the transaxle case No.1 plug from the transaxle
case.
(c) Remove the 5 O–rings from the transaxle cases.

C67755

8. FIX AUTOMATIC TRANSAXLE ASSY

[ 30500 / 3501 ]

C67756

9. REMOVE AUTOMATIC TRANSAXLE OIL PAN

SUB–ASSY
[ 35106D / 3503 ]
(a) Remove the drain plug and gasket from the oil pan.
(b) Remove the 19 bolts.
(c) Remove the oil pan and gasket.

C62684

10. REMOVE AUTOMATIC TRANSAXLE OIL PAN GASKET

[ 35168A / 3503 ]

U340E A/T REPAIR MANUAL (RM824E)

 40–3
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

11. REMOVE VALVE BODY OIL STRAINER ASSY

[ 35330 / 3512 ]
(a) Remove the 3 bolts and oil strainer assy.

C62685

(b) Remove the O–ring from the oil stainer.

C62926

12. REMOVE TRANSMISSION VALVE BODY ASSY

[ 35410 / 3512 ]
(a) Disconnect the 5 solenoid connectors.
(b) Remove the bolt, lock plate and ATF temperature sensor.

D25052

(c) Remove the 2 bolts, detente spring cover and detente

spring.

C64535

(d) Remove 13 bolts and valve body assy.

C81329

U340E A/T REPAIR MANUAL (RM824E)

40–4
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

13. REMOVE TRANSMISSION WIRE

[ 82125J / 3512 ]
(a) Remove the bolt.
(b) Remove the transmission wire from the transaxle case.

C62929

14. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET

[ 35149B / 3503 ]

C67757

15. REMOVE TRANSAXLE CASE GASKET

[ 35145C / 3503 ]

C67758

16. REMOVE BRAKE DRUM GASKET

[ 35159 / 3503 ]

C67759

17. REMOVE CHECK BALL BODY

[ 35251 / 3512 ]

C67767

U340E A/T REPAIR MANUAL (RM824E)

 40–5
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

18. REMOVE B–2 ACCUMULATOR PISTON

[ 35423 / 3512 ]
(a) Apply compressed air (392 kPa, 4.0 kgf
cm2, 57 psi) to the
oil hole and remove the B2 accumulator piston and spring.
Remove the spring.
NOTICE:

Blowing off the air may cause the piston’s jump–out.
When removing the piston, holding it with your hand
C67761 using a waste cloth.

Take care not to splash ATF when air–blowing.
(b) Remove the 2 O–rings from the B2 accumulator piston.

D25038

19. REMOVE C–3 ACCUMULATOR PISTON

[ 35426D / 3512 ]
(a) Apply compressed air (392 kPa, 4.0 kgf
cm2, 57 psi) to the
oil hole and remove the C3 accumulator piston and spring.
Remove the spring.
NOTICE:

Blowing off the air may cause the piston’s jump–out.
When removing the piston, holding it with your hand
C67762 using a waste cloth.

Take care not to splash ATF when air–blowing.
(b) Remove the 2 O–rings from the C3 accumulator piston.

D25039

20. REMOVE C–2 ACCUMULATOR PISTON

[ 35425A / 3512 ]
(a) Apply compressed air (392 kPa, 4.0 kgf
cm2, 57 psi) to the
oil hole and remove the C2 accumulator piston and spring.
Remove the spring.
NOTICE:

Blowing off the air may cause the piston’s jump–out.
When removing the piston, holding it with your hand
C67763 using a waste cloth.

Take care not to splash ATF when air–blowing.
U340E A/T REPAIR MANUAL (RM824E)
40–6
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(b) Remove the 2 O–rings from the C2 accumulator piston.

D25040

21. REMOVE TRANSAXLE HOUSING

[ 35111C / 4301 ]
(a) Remove the 14 bolts.
(b) Tap on the circumference of the transaxle housing with a
plastic hammer to remove the transaxle housing from the
transaxle case.
NOTICE:
Differential gear assembly may be accidentally removed
D25041 when the transaxle housing is removed.

22. REMOVE TRANSAXLE HOUSING OIL SEPARATOR

[ 35174 / 4301 ]
(a) Remove the 2 bolts and transaxle housing oil separator
from the transaxle housing.

C67769

23. REMOVE BEARING LOCK PLATE

[ 33326E / 3510 ]
(a) Remove the bolt.
(b) Remove the bearing lock plate.

C67770

24. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE

[ 35882D / 3510 ]
(a) Remove the bolt and differential gear lube apply tube
from the transaxle housing.

C68187

U340E A/T REPAIR MANUAL (RM824E)

 40–7
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

25. REMOVE FRONT DRIVE PINION FRONT TAPERED

SST


 Turn ROLLER BEARING
[ 41211A / 4301 ]
Hold (a) Using SST, remove the RH cylindrical roller bearing from
the transaxle housing.
SST 09308–10010

C67771

26. INSPECT INPUT SHAFT ENDPLAY

(a) Measure the end play in axial direction.
End play: 0.37 – 1.29 mm (0.0146 – 0.0508 in.)
If the end play is not as specified, select and replace the thrust
needle roller bearing.

C67772

27. REMOVE OIL PUMP ASSEMBLY

(a) Remove the 7 bolts and oil pump assy.

C67773

28. REMOVE DIFFERENTIAL GEAR ASSEMBLY

(a) Remove the differential gear assy.

D25042

29. REMOVE OVERDRIVE BRAKE GASKET

[ 35179 / 3503 ]
(a) Using a screwdriver, remove the 2 O/D brake gaskets
from the transaxle case.

C67783

U340E A/T REPAIR MANUAL (RM824E)

40–8
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

30. REMOVE INPUT SHAFT ASSY

(a) Remove the input shaft assy from the transaxle case.

C67775

31. REMOVE STATOR SHAFT THRUST NEEDLE ROLLER

BEARING
[ 35370A / 3502 ]
(a) Remove the thrust needle roller bearing from the input
shaft.

C67782

32. REMOVE FORWARD CLUTCH HUB THRUST NEEDLE

ROLLER BEARING
[ 35061C / 3507 ]
(a) Remove the thrust needle roller bearing from the forward
clutch hub.

C67776

33. INSPECT INTERMEDIATE SHAFT ASSY

(a) Using a dial indicator, measure the rickety of inter mediate
shaft.
Standard clearance:
0.204 – 0.966 mm (0.008 – 0.038 in.)

D25043

34. REMOVE FORWARD CLUTCH HUB SUB–ASSY

[ 35061 / 3507 ]
(a) Remove the forward clutch hub from the transaxle case.

C67777

U340E A/T REPAIR MANUAL (RM824E)

 40–9
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

35. REMOVE TRANSAXLE REAR COVER ASSY

(a) Remove the 11 bolts.
(b) Tap on the circumference of the transaxle rear cover with
a plastic hammer to remove the transaxle rear cover from
the transaxle case.

C67778

36. REMOVE TRANSAXLE CASE GASKET

[ 35145C / 3503 ]
(a) Remove the 4 transaxle case gaskets.

C67779

37. REMOVE REAR CLUTCH DRUM THRUST NEEDLE

ROLLER BEARING
[ 35651B / 3507 ]
(a) Using a magnetic hand, remove the thrust needle roller
bearing.

C67780

38. REMOVE INTERMEDIATE SHAFT ASSY

(a) Remove the intermediate shaft assy from the transaxle
case.

C67781

39. REMOVE 2ND COAST & OVERDRIVE BRAKE DISC

[ 34633 / 3509 ]
(a) Remove the flange, 2 discs and 2 flanges No.2 from the
transaxle.

C67785

U340E A/T REPAIR MANUAL (RM824E)

40–10
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

40. INSPECT 2ND COAST & OVERDRIVE BRAKE DISC

[ 34633 / 3509 ]
(a) Check to see if the sliding surface of the disc, plate and
flange are worn or burnt.
If necessary, replace them.
HINT:

If the lining of he disc is peeling off or discolored, or
even if a part of the printed number is defaced, re-
C67852 place all discs.

Before assembling new discs, soak them in ATF for
at least 15 minutes.

41. REMOVE THRUST NEEDLE ROLLER BEARING

[ 35605B / 3507 ]
(a) Using a magnetic finger, remove the C2 hub thrust bear-
ing race, thrust needle roller bearing and thrust bearing
race from the direct clutch hub.

C67784

42. REMOVE DIRECT CLUTCH HUB

[ 35654B / 3507 ]
(a) Remove the direct clutch hub from the transaxle case.

C68196

43. REMOVE REAR PLANETARY SUN GEAR, NO.2

THRUST NEEDLE BEARING
[ 35730C / 3510 ]
(a) Using a magnet finger, remove the thrust bearing from the
rear thrust needle bearing.

C67786

U340E A/T REPAIR MANUAL (RM824E)

 40–11
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

44. REMOVE REAR PLANETARY SUN GEAR ASSY

[ 35730 / 3510 ]
(a) Remove rear planetary sun gear from the transaxle case.

C67973

45. REMOVE REAR PLANERARY SUN GEAR THRUST

NEEDLE ROLLER BEARING
[ 35730B / 3510 ]
(a) Remove rear planetary sun gear thrust needle roller bear-
ing and thrust washer No.1 from the rear planetary sun
gear.

C68161

46. INSPECT 1 WAY CLUTCH ASSY

Free
[ 35790A / 3510 ]
(a) Hold the rear planetary sun gear and turn the 1 way
Lock
clutch. The 1 way clutch should turn freely clockwise and
should lock counterclockwise.

Lock

D25044

47. REMOVE 1 WAY CLUTCH ASSY

[ 35790A / 3510 ]
(a) Remove the 1 way clutch assy and planetary carrier thrust
washer No.2 from the rear planetary sun gear.

C68163

48. REMOVE 2ND COAST & OVERDRIVE BRAKE

FLANGE HOLE SNAP RING
[ 34625E / 3509 ]
(a) Using a screwdriver, remove the snap ring from the trans-
axle case.

C67971

U340E A/T REPAIR MANUAL (RM824E)

40–12
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

49. REMOVE 2ND BRAKE BRAKE DISC

[ 35682 / 3509 ]
(a) Using a screwdriver, remove the snap ring.
(b) Remove the flange, 3 discs and 3 plates from the trans-
axle.

C67969

50. INSPECT 2ND BRAKE BRAKE DISC

[ 35682 / 3509 ]
(a) Check to see if the sliding surface of the disc, plate and
flange are worn or burnt.
If necessary, replace them.
HINT:

If the lining of the disc is peeling off or discolored or
even if a part of the printed mark is defaced, replace
C67852 all discs.

Before assembling new discs, soak them in ATF for
at least 15 minutes.

51. REMOVE 2ND BRAKE PISTON SLEEVE

[ 35626D / 3509 ]
(a) Remove the 2nd brake piston sleeve from the transaxle
case.

C67970

52. INSPECT 1 WAY CLUTCH NO.2

[ 35792C / 3509 ]
Free Lock
(a) Install the 1 way clutch and thrust washer to the rear plan-
etary sun gear.
(b) Hold the rear planetary sun gear and turn the 1 way
clutch. The 1 way clutch should turn freely clockwise and
should lock counterclockwise.

D25045

U340E A/T REPAIR MANUAL (RM824E)

 40–13
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

53. REMOVE REAR PLANETARY GEAR ASSY

[ 35760 / 3510 ]
(a) Using a screwdriver, remove the snap ring.
(b) Remove the rear planetary gear assy from the transaxle
case.

C67967

54. REMOVE PLANETARY GEAR REAR THRUST

NEEDLE ROLLER BEARING
[ 35720K / 3510 ]
(a) Remove the thrust needle roller bearing and 2 bearing
races from the rear planetary gear assy.

C68159

55. REMOVE 1 WAY CLUTCH NO.2

[ 35792C / 3509 ]
(a) Separate the 2nd brake cylinder, 1 way clutch No.2 and
rear planetary gear.

C67966

56. REMOVE OUTER RACE RETAINER

[ 34365A / 3503 ]
(a) Remove the retainer from the 1 way clutch No.2.

C67965

57. REMOVE FR PLANETARY SUN GEAR

[ 35714D / 3510 ]
(a) Remove the front planetary sun gear and thrust needle
roller bearing from the transaxle case.

C68157

U340E A/T REPAIR MANUAL (RM824E)

40–14
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

58. REMOVE 1ST & REVERSE BRAKE DISC

[ 35683 / 3509 ]
(a) Using a screwdriver, remove the snap ring.
(b) Remove the flange, 4 discs and 4 plates from the trans-
axle case.

C67963

59. INSPECT 1ST & REVERSE BRAKE DISC

[ 35683 / 3509 ]
(a) Check to see if the sliding surface of the disc, plate and
flange are worn or burnt.
If necessary, replace them.
HINT:

If the lining of the disc is peeling off or discolored, or
even if a part of the printed mark is defaced, replace
D25046 all discs.

Before assembling new discs, soak in ATF for at least
15 minutes.

60. REMOVE 1ST & REVERSE BRAKE RETURN SPRING

SUB–ASSY
[ 35068 / 3509 ]
(a) Using SST, a press and a screwdriver, remove the snap
ring.
SST 09387–00070
(b) Remove the 1st & reverse brake return spring sub–assy.
SST
D08332

61. INSPECT 1ST & REVERSE BRAKE RETURN SPRING

SUB–ASSY
[ 35068 / 3509 ]
(a) Using a vernier calipers, measure the free length of the
spring together with the spring seat.
Standard free length: 13.96 mm (0.5496 in.)

C59838

U340E A/T REPAIR MANUAL (RM824E)

 40–15
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

62. REMOVE 1ST & REVERSE BRAKE PISTON NO.2

[ 35623P / 3509 ]
(a) Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the
transaxle case to remove the 1st & reverse brake piston.
NOTICE:

Blowing off the air may cause the piston’s jump–out.
When removing the piston, hold it with your hand us-
ing a waste cloth.
C68211
Take care not to splash ATF when air–blowing.

63. REMOVE 1ST & REVERSE BRAKE PISTON NO.2

O–RING
[ 35623Q / 3509 ]
(a) Remove the 2 O–rings from the1st & reverse brake piston
No.2.

C67962

64. REMOVE COUNTER DRIVE GEAR NUT

[ 35782H / 3510 ]
(a) Fix the counter driven gear with the parking lock pawl.

C67960

(b) Using SST and a hammer, unstake the lock washer.

 SST 09930–00010

C67961

(c) Using SST, remove the nut and lock washer.

SST 09387–00120
SST

D25048

U340E A/T REPAIR MANUAL (RM824E)

40–16
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

65. REMOVE PLANETARY GEAR ASSY

[ 35720G / 3510 ]
(a) Using SST and a press, remove the planetary gear assy



from the transaxle case.
SST 09950–60010 (09951–00400, 09951–00320,
09952–06010), 09950–70010 (09951–07100)

D25047

66. REMOVE COUNTER DRIVE GEAR

[ 35782C / 3510 ]
(a) Install the 2 bolts to the counter drive gear.
Bolt (M6):
L=40 – 80 mm
Pitch = 1.0 mm
(b) Rotate 2 bolts in order and remove the counter drive gear
and front planetary sun gear.
(c) Remove 2 radial ball bearings from the counter drive gear
and front planetary sun gear.


 
 C68474

67. REMOVE PARKING LOCK PAWL BRACKET

[ 35595 / 3513 ]
(a) Remove the 3 bolts, cam guide and bracket.

C67957

U340E A/T REPAIR MANUAL (RM824E)

 40–17
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

68. REMOVE MANUAL VALVE LEVER SHAFT RETAINER

SPRING
[ 35506J / 3513 ]
(a) Remove the retainer spring.

C67956

69. REMOVE MANUAL VALVE LEVER SUB–ASSY

[ 35505 / 3513 ]
(a) Using a screwdriver, unstake and remove the spacer.

C67954

(b) Using a pin punch and hammer, drive out the pin.
(c) Remove the manual valve lever shaft and manual valve
lever.

C67950

70. REMOVE PARKING LOCK ROD SUB–ASSY

[ 35501 / 3513 ]
(a) Remove the parking lock rod from the manual valve lever.

C67951

71. REMOVE MANUAL VALVE LEVER SHAFT

[ 35561 / 3513 ]
(a) Remove the manual valve lever shaft from the transaxle
case.

C67952

U340E A/T REPAIR MANUAL (RM824E)

40–18
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

72. REMOVE PARKING LOCK PAWL

[ 35557 / 3513 ]
(a) Using a screwdriver, remove the parking lock pawl shaft.
(b) Remove the torsion spring and parking lock pawl.

C67948

73. REMOVE COUNTER DRIVEN GEAR

[ 35783R / 4301 ]
(a) Remove the counter driven gear, drive pinion and thrust
needle roller bearing from the transaxle case.

C68164

74. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL

[ 35506F / 3513 ]
(a) Using a screwdriver, remove the oil seal.

C67953

75. REMOVE COUNTER DRIVE GEAR BEARING

[ 35782E / 3510 ]
(a) Remove the 2 counter drive gear bearing inner races RH
the transaxle case.
(b) Using SST, remove the counter drive gear bearing LH out-
er race from the transaxle case
SST 09308–00010

D25049

(c) Using SST, remove the counter drive gear bearing rear
outer race from the transaxle case.
SST 09308–00010

D25050

U340E A/T REPAIR MANUAL (RM824E)

 40–19
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

76. REMOVE COUNTER DRIVE GEAR HOLE SNAP RING

[ 35782D / 3510 ]
(a) Using a screwdriver, remove the counter drive gear hole
snap ring from the transaxle case.

C67955

77. REMOVE BREATHER PLUG HOSE(U340E A/T)

[ 35104V / 3503 ]

C67752

78. REMOVE FRONT DRIVE PINION REAR TAPERED

ROLLER BEARING
[ 41211B / 4301 ]



(a) Using SST, remove front drive pinion LH cylindrical roller
bearing from the transaxle case.
SST 09612–65014 (09612–01040)

C67946

79. REMOVE FR DIFFERENTIAL CASE FRONT TAPERED

ROLLER BEARING
[ 41311E / 4301 ]
(a) Using SST, remove the front differential case RH tapered


 roller bearing from the differential case.
SST 09950–40011 (09951–04010, 09952–04010,
09953–04030, 09954–04010, 09955–04061,
09957–04010, 09958–04011), 09950–60010
C68434 (09951–00390)

(b) Using SST, remove the front differential case RH tapered

roller bearing outer race from the transaxle housing.
SST 09387–00040 (09387–02020, 09387–02010)




C67940

U340E A/T REPAIR MANUAL (RM824E)

40–20
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

80. REMOVE FR DIFFERENTIAL CASE REAR TAPERED

ROLLER BEARING
[ 41311F / 4301 ]



(a) Using SST, remove the front differential case tapered roll-
er bearing from the differential case.
SST 09950–40011 (09951–04010, 09952–04010,
09953–04020, 09954–04010, 09955–04061,
09957–04010, 09958–04011), 09950–60010
C67944 (09951–00430)

(b) Using SST, remove front differences.

SST 09612–65014 (09612–01010)



C67943

81. REMOVE FRONT TRANSAXLE CASE OIL SEAL

 [ 31105D / 4301 ]
(a) Using SST and a hammer, remove the oil seal from the
transaxle case.
SST 09950–60010 (09951–00550), 09950–70010
(09951–07100)

C67942

82. REMOVE TRANSAXLE CASE OIL SEAL

 [ 31105H / 4301 ]
(a) Using SST and a hammer, remove the transaxle case oil
seal from the transaxle housing.
SST 09950–60010 (09951–00530), 09950–70010
(09951–07100)

C67941

U340E A/T REPAIR MANUAL (RM824E)

 40–21
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

83. BEARING POSITION

C
B

G
F
C68166

U340E A/T REPAIR MANUAL (RM824E)

40–22
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

Front Race Diameter Thrust Bearing Diameter Rear Race Diameter

Mark
Inside / Outside mm (in.) Inside / Outside mm (in.) Inside / Outside mm (in.)
A – 45.1 (1.7756) / 65.1 (2.5630) –
B – 26 (1.0236) / 43.4 (1.7087) –
C – 21 (0.8268) / 34.85 (1.3721) –
D – 32.0 (1.260) / 48.0 (1.890) –
E 36.75 (1.447) / 49.95 (1.967) 33.9 (1.335) / 52.0 (2.047) – / 51.7 (2.035)
F – 43.45 (1.7101) / 58.5 (2.3031) –
G – 29.4 (1.1574) / 44.4 (1.7480) –
H 23.5 (0.9252) / 37.3 (1.4685) 22.5 (0.8858) / 37.3 (1.4685) 20.3 (0.7992) / 33.8 (1.3307)
43.45 (1.7101) / 61.2 (2.4094)
I – or –
43.45 (1.7101) / 61.74 (2.4307)

U340E A/T REPAIR MANUAL (RM824E)

 40–23
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

84. INSTALL FR DIFFERENTIAL CASE REAR TAPERED

ROLLER BEARING
͓͓͔ [ 41311F / 4301 ]
(a) Using SST and a press, install the front differential case
LH tapered roller bearing inner race to the differential
case.
SST 09726–40010, 09950–60020 (09951–00790)

C68169

(b) Using SST and a press, install the shim and bearing outer
͓͓͔ race to the transaxle case.
SST 09950–60010 (09951–00650), 09950–60020
(09951–00720), 09950–70010 (09951–07100,
09951–07200)

͓͓͔ C68191

85. INSTALL FR DIFFERENTIAL CASE FRONT TAPERED

ROLLER BEARING
[ 41311E / 4301 ]
(a) Using SST and a press, install the bearing inner race to
the differential case.
SST 09950–60010 (09951–00460), 09950–70010
(09951–07100)

D25051

(b) Using SST and a press, install the tapered roller bearing
to the transaxle housing.
͓͓͔ SST 09950–60020 (09951–00680), 09950–70010
(09951–07150)

C68208

́ 86. TAPERED POLLER BEARING PRELOAD

͂
́ (a) Coat the front differential case and bearing with ATF and
install them to the transaxle case.
(b) Install the 14 bolts and transaxle housing.
Torque:
Bolt A: 29 N
m (300 kgf
cm, 21 ft
lbf)
Bolt B: 22 N
m (220 kgf
cm, 16 ft
lbf)
́ ́
D25285

U340E A/T REPAIR MANUAL (RM824E)

40–24
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(c) Using SST and small torque wrench, measure the pre-



load of the differential gear.
SST 09564–32011
Preload:
New bearing:
0.98 – 1.57 N
m (10.0 – 16.0 kgf
cm 8.7 – 13.9 in.
lbf)
Used bearing:
0.49 – 0.78 N
m (5.0 – 8.0 kgf
cm 4.3 – 6.9 in.
lbf)
C81338 If the preload is not within the specification, remove the differen-
tial from the transaxle case. Re–select the transaxle case side
adjusting shim according to the following table.
Adjusting shim thickness: mm (in.)
Mark Thickness Mark Thickness
01 1.90 (0.0748) 11 2.40 (0.0945)
02 1.95 (0.0768) 12 2.45 (0.0965)
03 2.00 (0.0787) 13 2.50 (0.0984)
04 2.05 (0.0807) 14 2.55 (0.1004)
05 2.10 (0.0827) 15 2.60 (0.1024)
06 2.15 (0.0846) 16 2.65 (0.1043)
07 2.20 (0.0866) 17 2.70 (0.1063)
08 2.25 (0.0885) 18 2.75 (0.1082)
09 2.30 (0.0906) 19 2.80 (0.1102)
10 2.35 (0.0925) – –

87. INSTALL TRANSAXLE CASE OIL SEAL

[ 31105H / 4301 ]
(a) Using SST and a hammer, drive in a new oil seal.
SST 09554–14010, 09950–70010 (09951–07100)
Oil seal in depth:



2
0.5 mm (0.079
0.020 in.)

C68168

88. INSTALL FRONT TRANSAXLE CASE OIL SEAL

[ 31105D / 4301 ]
(a) Using SST and a hammer, drive in a new oil seal.
SST 09726–27012 (09726–02041), 09950–70010


 (09951–07150)
Oil seal in depth:
5.9
0.5 mm (0.232
0.020 in.)

C68167

U340E A/T REPAIR MANUAL (RM824E)

 40–25
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

89. INSTALL FRONT DRIVE PINION REAR TAPERED

ROLLER BEARING
[ 41211B / 4301 ]
(a) Using SST and a hammer, install the roller bearing in to
the transaxle case.
SST 09950–60010 (09951–00610), 09950–70010
(09951–07150)




C68171

90. INSTALL COUNTER DRIVE GEAR HOLE SNAP RING

[ 35782D / 3510 ]
(a) Using a screwdriver, install the counter drive gear hole
snap ring to the transaxle case.

C67955

91. INSTALL BREATHER PLUG HOSE(U340E A/T)

[ 35104V / 3503 ]

C67752

92. INSTALL COUNTER DRIVE GEAR BEARING

[ 35782E / 3510 ]
(a) Using SST and a hammer, install the counter drive gear
bearing LH outer race to the transaxle case.
SST 09950–60020 (09951–00890), 09950–70010
(09951–07150)


C68173

(b) Using SST and a hammer, install the counter drive gear
bearing RH outer race to the transaxle case.
SST 09950–60020 (09951–00890), 09950–70010
(09951–07150)


 (c) Install the counter drive gear bearing to the transaxle
case.

C68172

U340E A/T REPAIR MANUAL (RM824E)

40–26
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

93. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

[ 35506F / 3513 ]
(a) Using SST and a hammer, install the new manual valve


 lever shaft oil seal.
SST 09950–60010 (09951–00220), 09950–70010
(09951–07100)
Oil seal in depth:
0
0.5 mm (0
0.020 in.)
C68174

94. INSTALL COUNTER DRIVEN GEAR

[ 35783R / 4301 ]
(a) Install the counter driven gear and drive pinion thrust
bearing to the transaxle case.

C68165

95. INSTALL PARKING LOCK PAWL

[ 35557 / 3513 ]
(a) Coat the parking lock pawl shaft with ATF.
(b) Install the parking lock pawl, torsion spring and shaft to
the transaxle case.
HINT:
Check that the parking lock pawl can move smoothly.

C67948

96. INSTALL MANUAL VALVE LEVER SHAFT

[ 35561 / 3513 ]
(a) Install the manual valve lever shaft to the transaxle case.
NOTICE:
Be careful not to damage the oil seal lip.

C67952

97. INSTALL PARKING LOCK ROD SUB–ASSY

[ 35501 / 3513 ]
98. INSTALL MANUAL VALVE LEVER SUB–ASSY
[ 35505 / 3513 ]
(a) Coat the manual valve lever sub–assy with ATF.
(b) Install the manual valve lever and a new manual valve le-
ver spacer to the manual valve lever shaft.

C67951

U340E A/T REPAIR MANUAL (RM824E)

 40–27
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(c) Using a pin punch and hammer, drive in the pin.

C67950

(d) Turn the spacer and lever shaft to align the small hole for
locating the staking position in the spacer with the staking
position mark on the lever shaft.
(e) Using a pin punch, stake the spacer through the small
hole.
(f) Check that the space does not turn.

C68175

99. INSTALL MANUAL VALVE LEVER SHAFT RETAINER

SPRING
[ 35506J / 3513 ]
(a) Install the retainer spring.

C67956

100. INSTALL PARKING LOCK PAWL BRACKET

[ 35595 / 3513 ]
(a) Install the cam guide, bracket and 3 bolts.
Torque: 20 N
m (200 kgf
cm, 14 ft
lbf)

C67957

U340E A/T REPAIR MANUAL (RM824E)

40–28
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

101. INSTALL COUNTER DRIVE GEAR

[ 35782C / 3510 ]
(a) Using SST and a press, install the counter drive gear to
the transaxle case.
SST 09223–15030, 09527–17011, 09950–60010
(09951–00650), 09950–70010 (09951–07150)






D25054

102. INSTALL PLANETARY GEAR ASSY

[ 35720G / 3510 ]
(a) Using SST and a press, install the planetary gear assy to
the transaxle case.
SST 09950–60010 (09951–00480), 09223–15030,
09527–17011, 09950–70010 (09951–07150)






D25053

103. INSTALL COUNTER DRIVE GEAR NUT

[ 35782H / 3510 ]
(a) Fix the counter driven gear with the parking lock pawl.

C67960

U340E A/T REPAIR MANUAL (RM824E)

 40–29
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(b) Using SST, install a new lock washer and nut.

 SST 09387–00120
Torque: 280 N
m (2,855 kgf
cm, 207 ft
lbf)

C68178

(c) Using SST and a small torque wrench, while turning to

counter drive gear 60 turn par minute and measure the ro-



tating torque.
SST 09387–00120
Rotating torque:
0.20 – 0.49 N
m (2 – 5 kgf
cm, 2 – 4 in.
lbf)

C68179

(d) Using SST and a hammer, stake the lock nut washer.



SST 09930–00010

C68469

104. INSTALL 1ST & REVERSE BRAKE PISTON NO.2

O–RING
[ 35623Q / 3509 ]
(a) Install the 2 O–rings.

C67962

105. INSTALL 1ST & REVERSE BRAKE PISTON NO.2

[ 35623P / 3509 ]
(a) Install the 1st & reverse brake piston to the transaxle
case.
NOTICE:
Be careful not to damage the oil seal lip.

C68210

U340E A/T REPAIR MANUAL (RM824E)

40–30
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

106. INSTALL 1ST & REVERSE BRAKE RETURN SPRING

SUB–ASSY
[ 35068 / 3509 ]
(a) Install the 1st & reverse brake return spring sub–assy to
the transaxle case.
(b) Using SST, a press and a screwdriver, install the snap
ring.
SST SST 09387–00070
D08332

107. INSTALL 1ST & REVERSE BRAKE DISC

Flange
[ 35683 / 3509 ]
Disc (a) Install the 4 plates, 4 discs and flange to the transaxle
case.
(b) Using a screwdriver, install the snap ring.
Plate

D25055

108. INSPECT PACK CLEARANCE OF FIRST & REVERSE

 BRAKE
(a) Using SST and a dial indicator, measure the dimension
”A” in the illustration while pressing the disc and plate from
the rear side.
SST 09350–36010 (09350–06110)
Pack clearance: 0.806 – 1.206 mm (0.0317 – 0.0475 in.)
HINT:
C68184 Pack clearance = Dimension A – Flange thickness – Snap ring
thickness
Select flange thickness: mm (in.)
Mark Thickness Mark Thickness
– 3.4 (0.134) 2 3.8 (0.150)
1 3.6 (0.142) 3 4.0 (0.157)

(b) Check that the 1st & reverse brake piston moves when
applying compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to
the oil hole.

109. INSTALL FR PLANETARY SUN GEAR

[ 35714D / 3510 ]
(a) Install the planetary sun gear and needle roller bearing to
the planetary gear assy.

C68158
U340E A/T REPAIR MANUAL (RM824E)
 40–31
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

110. INSTALL OUTER RACE RETAINER

[ 34365A / 3503 ]
(a) Install outer retainer to the 1 way clutch No.2.

C67965

111. INSTALL 1 WAY CLUTCH NO.2

[ 35792C / 3509 ]
(a) Install the 1 way clutch and a 2nd brake piston assy to the
rear planetary gear assy.

C67966

112. INSTALL PLANETARY GEAR REAR THRUST NEEDLE

ROLLER BEARING
[ 35720K / 3510 ]
(a) Install the thrust bearing race No. 2, planetary gear thrust
needle roller bearing and a thrust bearing race No.1 to the
rear planetary gear assy.

C68160

113. INSTALL REAR PLANETARY GEAR ASSY

[ 35760 / 3510 ]
(a) Install the rear planetary gear assy to the transaxle case
to the transaxle case.
(b) Using a screwdriver, install the snap ring.

D25056

114. INSPECT 1 WAY CLUTCH NO.2

[ 35792C / 3509 ]
Free Lock
(a) Check that the rear planetary gear turns freely counter-
clockwise and locks clockwise.

D25045

U340E A/T REPAIR MANUAL (RM824E)

40–32
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

115. INSTALL 2ND BRAKE PISTON SLEEVE

[ 35626D / 3509 ]
(a) Install the 2nd brake piston sleeve to the transaxle case.

C67970

116. INSTALL 2ND BRAKE BRAKE DISC

[ 35682 / 3509 ]
Flange
(a) Install the 3 discs, 3 plates and flange to the transaxle
case.
(b) Using a screwdriver, install the snap ring to the transaxle
case.
Disc
Plate

D25097

117. INSPECT PACK CLEARANCE OF SECOND BRAKE

(a) Using a dial indicator, measure the 2nd brake pack clear-
ance while applying and releasing compressed air (392
– 785 kPa, 4 – 8 kgf
cm2, 57 – 114 psi).
Pack clearance: 0.847 – 1.247 mm (0.0333 – 0.0491 in.)
HINT:
Pack clearance = Dimension A – Selected flange thickness –
Snap ring thickness.
D25098 Selected flange thickness: mm (in.)
Mark Thickness Mark Thickness
– 3.0 (0.118) 2 3.4 (0.134)
1 3.2 (0.126) 3 3.6 (0.142)

118. INSTALL 2ND COAST & OVERDRIVE BRAKE

FLANGE HOLE SNAP RING
[ 34625E / 3509 ]
(a) Using a screwdriver, install the snap ring to the transaxle
case.

C67971

U340E A/T REPAIR MANUAL (RM824E)

 40–33
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

119. INSTALL 1 WAY CLUTCH ASSY

[ 35790A / 3510 ]
(a) Install the thrust washer No.2 to the rear planetary gear
assy.
(b) Install the 1 way clutch assy to the rear planetary sun gear
assy.

C68163

120. INSPECT 1 WAY CLUTCH ASSY

Free
[ 35790A / 3510 ]
(a) Hold the rear planetary sun gear and turn the 1 way
clutch. The 1 way clutch should turn freely clockwise and
Lock
should lock counterclockwise.

Lock

D25044

121. INSTALL REAR PLANERARY SUN GEAR THRUST

NEEDLE ROLLER BEARING
[ 35730B / 3510 ]
(a) Install the thrust bearing and a washer to the rear plane-
tary sun gear.

C68162

122. INSTALL REAR PLANETARY SUN GEAR ASSY

[ 35730 / 3510 ]
(a) Install the rear planetary sun gear assy.

C67973

123. INSTALL REAR PLANETARY SUN GEAR, NO.2

THRUST NEEDLE BEARING
[ 35730C / 3510 ]
(a) Install the thrust bearing to the rear planetary sun gear.

C68466

U340E A/T REPAIR MANUAL (RM824E)

40–34
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

124. INSTALL DIRECT CLUTCH HUB

[ 35654B / 3507 ]
(a) Install the direct clutch hub.

C68196

125. INSTALL THRUST NEEDLE ROLLER BEARING

[ 35605B / 3507 ]
(a) Install the thrust bearing race No.3, thrust needle roller
bearing and a C2 hub thrust bearing race to the direct
clutch hub.

C68465

126. INSTALL 2ND COAST & OVERDRIVE BRAKE DISC

[ 34633 / 3509 ]
(a) Install the 2 discs, 2 plates and a flange to the transaxle
case.
Flange
Disc

Plate
D25099

127. INSTALL INTERMEDIATE SHAFT ASSY

(a) Install the intermediate shaft assy to the transaxle case.

C67781

128. INSPECT PACK CLEARANCE OF SECOND COAST &

OVER DRIVE BRAKE
(a) As shown in the illustration, place a straight edge on the
transaxle case and measure the distance between the
2nd coast & O/D brake flange and straight edge using ver-
nier calipers. (Dimension A)

C68205

U340E A/T REPAIR MANUAL (RM824E)

 40–35
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(b) As shown in the illustration, place a straight edge on the

O/D brake piston and measure the distance between the
transaxle rear cove and straight edge using vernier cali-


pers. (Dimension B)
Calculate the piston stroke value using the following for-
mula. Select a flange which satisfies the piston stroke val-
ue and install it.
Pack clearance: 2.091 – 2.491 mm (0.0823 – 0.0981 in)
C68206 HINT:
Pack clearance = Dimension ”A” – Dimension ”B” – Selected
flange thickness.
Selected flange thickness: mm (in.)
Mark Thickness Mark Thickness
4 4.0 (0.1575) 6 4.4 (0.1732)
5 4.2 (0.1654) 7 4.6 (0.1811)

129. INSTALL REAR CLUTCH DRUM THRUST NEEDLE

ROLLER BEARING
[ 35651B / 3507 ]
(a) Install the bearing to the intermediate shaft.

C68467

130. INSPECT INTERMEDIATE SHAFT ASSY

(a) Install the transaxle rear cover and 11 bolts.
Torque: 24.5 N
m (250 kgf
cm, 18 ft
lbf)

C67778

(b) Using a dial indicator, measure the rickety of intermediate

shaft.
Standard clearance:
0.204 – 0.966 mm (0.008 – 0.038 in.)
(c) Remove 11 bolts and transaxle rear cover.

D25043

U340E A/T REPAIR MANUAL (RM824E)

40–36
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

131. INSTALL TRANSAXLE CASE GASKET

[ 35145C / 3503 ]
(a) Install the 4 new gaskets to the transaxle case.

C67779

132. INSTALL TRANSAXLE REAR COVER ASSY

(a) Apply FIPG to the transaxle case.
FIPG:
Part NO. 08826–00090, THREE BOND 1281 or equiva-
lent

C68204

(b) Install the transaxle rear cover and 11 bolts.

Torque: 24.5 N
m (250 kgf
cm, 18 ft
lbf)

C67778

133. INSTALL FORWARD CLUTCH HUB SUB–ASSY

[ 35061 / 3507 ]
(a) Install the forward clutch hub sub–assy to the transaxle
case.

C67777

134. INSTALL FORWARD CLUTCH HUB THRUST NEEDLE

ROLLER BEARING
[ 35061C / 3507 ]
(a) Install the bearing to the forward clutch hub.

C68464

U340E A/T REPAIR MANUAL (RM824E)

 40–37
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

135. INSTALL STATOR SHAFT THRUST NEEDLE ROLLER

BEARING
[ 35370A / 3502 ]
(a) Install the bearing to the input shaft assy.

C67938

136. INSTALL INPUT SHAFT ASSY

(a) Install the input shaft assy to the transaxle case.

C67775

137. INSTALL OVERDRIVE BRAKE GASKET

[ 35179 / 3503 ]
(a) Install 2 new gaskets to the transaxle case.

C67783

138. INSTALL DIFFERENTIAL GEAR ASSEMBLY

(a) Install the differential gear assy to the transaxle case.

D25100

139. INSTALL OIL PUMP ASSEMBLY

(a) Install the 7 bolts and oil pump.
Torque: 22 N
m (220 kgf
cm, 16 ft
lbf)

C67773

U340E A/T REPAIR MANUAL (RM824E)

40–38
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

140. INSPECT INPUT SHAFT ASSY

(a) Make sure that the input shaft turns smoothly.

C68186

141. INSPECT INPUT SHAFT ENDPLAY

(a) Measure the end play in axial direction.
End play: 0.37 – 1.29 mm (0.0146 – 0.0508 in.)
If the end play is not as specified, select and replace the thrust
needle roller bearing.
142. INSTALL FRONT DRIVE PINION FRONT TAPERED
ROLLER BEARING
[ 41211A / 4301 ]
C67772 (a) Install the thrust bearing to the transaxle housing.

(b) Using SST and a press, install the cylindrical roller bear-
ing to the transaxle housing.
SST 09950–60010 (09951–00650), 09950–70010
(09951–07150)




C68209

143. INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

[ 35882D / 3510 ]

C68187

144. INSTALL BEARING LOCK PLATE

[ 33326E / 3510 ]
(a) Install the bolt and bearing lock plate to the transaxle
housing.
Torque: 11 N
m (110 kgf
cm, 8 ft
lbf)

C67770

U340E A/T REPAIR MANUAL (RM824E)

 40–39
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

145. INSTALL TRANSAXLE HOUSING OIL SEPARATOR

[ 35174 / 4301 ]
(a) Install the 2 bolts and oil separator to the transaxle hous-
ing.
Torque: 9.8 N
m (100 kgf
cm, 7 ft
lbf)

C67769

146. INSTALL TRANSAXLE HOUSING

[ 35111C / 4301 ]
(a) Apply FIPG to the transaxle case.
FIPG:
Part No.08826–00090, THREE BOND 1281 or equiva-
lent

C81344

(b) Install the 14 bolts and transaxle housing.

́ Torque:
͂
́ Bolt A: 29 N
m (300 kgf
cm, 21 ft
lbf)
Bolt B: 22 N
m (220 kgf
cm, 16 ft
lbf)

́ ́

́
͂
́

́ D25101

147. INSTALL C–2 ACCUMULATOR PISTON

[ 35425A / 3512 ]
(a) Coat new 2 O–rings with ATF and install them to the C2
Accumulator piston.
NOTICE:
Be careful not to damage the O–ring.

D25040

U340E A/T REPAIR MANUAL (RM824E)

40–40
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(b) Install the spring and C2 accumulator piston.

Accumulator spring:
Free length/
Spring Color
Outer diameter mm (in.)
66.90 (2.6339)/
C2 –
17.20 (0.6772)

C68839

148. INSTALL C–3 ACCUMULATOR PISTON

[ 35426D / 3512 ]
(a) Coat new 2 O–rings with ATF and install them to the C3
accumulator piston.
NOTICE:
Be careful not to damage the O–ring.

D25039

(b) Install the spring and C3 accumulator piston.

Accumulator spring:
Free length/
Spring Color
Outer diameter mm (in.)
80.20 (3.1575)/
C3 Blue
18.70 (0.7362)

C68840

149. INSTALL B–2 ACCUMULATOR PISTON

[ 35423 / 3512 ]
(a) Coat new 2 O–rings with ATF and install them to the B2
accumulator piston.
NOTICE:
Be careful not to damage the O–ring.

D25038

(b) Install the spring and B2 accumulator piston.

Accumulator spring:
Free length/
Spring Color
Outer diameter mm (in.)
66.90 (2.6339)/
B2 Green
15.50 (0.6102)

C68841

U340E A/T REPAIR MANUAL (RM824E)

 40–41
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

150. INSTALL CHECK BALL BODY

[ 35251 / 3512 ]
(a) Install the spring and check ball body.

C69422

151. INSTALL BRAKE DRUM GASKET

[ 35159 / 3503 ]
(a) Install a new brake drum gasket.

C67759

152. INSTALL TRANSAXLE CASE GASKET

[ 35145C / 3503 ]
(a) Install a new transaxle case gasket.

C67758

153. INSTALL TRANSAXLE CASE 2ND BRAKE GASKET

[ 35149B / 3503 ]
(a) Install a new transmission case 2nd brake gasket.

C67757

154. INSTALL TRANSMISSION WIRE

[ 82125J / 3512 ]
(a) Coat a new O–ring with ATF, install it to the transaxle wire.

C67760

U340E A/T REPAIR MANUAL (RM824E)

40–42
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

(b) Pierce the transmission wire to the transaxle.

D25102

(c) Install the bolt and transaxle wire.

Torque: 5.4 N
m (55 kgf
cm, 48 ft
lbf)

C62929

́ ͂ 155. INSTALL TRANSMISSION VALVE BODY ASSY

̓ [ 35410 / 3512 ]
(a) Install the valve body assembly and 13 bolts.
́ Torque: 11 N
m (110 kgf
cm, 8 ft
lbf)
̈́ Bolt length:
Bolt A: 32 mm (1.26 in.)
́ Bolt B: 22 mm (0.87 in.)
͂
Bolt C: 55 mm (2.17 in.)
C81346 Bolt D: 45 mm (1.77 in.)

(b) Install the detente spring, detente spring cover and 2

bolts.
Torque: 11 N
m (110 kgf
cm, 8 ft
lbf)
Bolt length:
́ Bolt A: 14 mm (0.55 in.)
Bolt B: 45 mm (1.77 in.)
͂
(c) Check that the manual valve lever is touching the center
of the detente spring tip roller.
C62687

(d) Connect the 5 solenoid connectors.

(e) Coat a new O–ring with ATF, install it to the ATF tempera-
ture sensor.
(f) Install the ATF temperature sensor, lock plate and bolt.
Torque: 11 N
m (110 kgf
cm, 8 ft
lbf)
Bolt length: 55 mm (2.17 in.)

D25103

U340E A/T REPAIR MANUAL (RM824E)

 40–43
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

156. INSTALL VALVE BODY OIL STRAINER ASSY

[ 35330 / 3512 ]
(a) Coat a new O–ring with ATF, install it to the oil strainer.

C62926

(b) Install the oil strainer and 3 bolts.

Torque: 11 N
m (110 kgf
cm, 8 ft
lbf)

C62685

157. INSTALL AUTOMATIC TRANSAXLE OIL PAN GASKET

[ 35168A / 3503 ]
(a) Install the new gasket to the oil pan.

158. INSTALL AUTOMATIC TRANSAXLE OIL PAN

SUB–ASSY
[ 35106D / 3503 ]
(a) Install the 2 magnets in the oil pan.

D25104

(b) Install the oil pan sub–assy and 19 bolts.

Torque: 7.8 N
m (80 kgf
cm, 71 in.
lbf)

C62684

U340E A/T REPAIR MANUAL (RM824E)

40–44
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

159. INSTALL TRANSAXLE CASE NO.1 PLUG

[ 35104Q / 3503 ]
(a) Coat 5 new O–rings with ATF, install them to the screw
plugs.
(b) Install the 4 screw plugs.
Torque: 7.4 N
m (75 kgf
cm, 65 in.
lbf)

C67754

(c) Install the screw plug.

Torque: 7.4 N
m (75 kgf
cm, 65 in.
lbf)

C67755

160. INSTALL OIL COOLER TUBE UNION(INLET OIL

COOLER UNION)
[ 32921C / 3514 ]
(a) coat 2 new O–rings with ATF, install them to the union.
(b) Install the union.
Torque: 27 N
m (275 kgf
cm, 20 ft
lbf)

C80725

161. INSTALL OIL COOLER TUBE UNION(OUTLET OIL

COOLER UNION)
[ 32921C / 3514 ]
(a) coat 2 new O–rings with ATF, install them to the elbow.
(b) Install the elbow.
Torque: 27 N
m (275 kgf
cm, 20 ft
lbf)

D25286

162. INSTALL TRANSMISSION REVOLUTION SENSOR

[ 89413E / 3512 ]
(a) Install the bolt and transmission revolution sensor.
Torque: 5.4 N
m (55 kgf
cm, 48 in.
lbf)

C67751

U340E A/T REPAIR MANUAL (RM824E)

 40–45
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

163. INSTALL NEUTRAL START SWITCH ASSY

[ 84540G / 3513 ]
(a) Install the park/neutral position switch onto the manual
valve lever shaft and temporarily install the 2 adjusting
bolts.
(b) Install a new lock washer and nuts.
Torque: 6.9 N
m (70 kgf
cm, 61 in.
lbf)
(c) Temporarily install the control lever.
C62665

(d) Turn the lever counterclockwise until it stops, then turn it

clockwise 2 notches.
(e) Remove the control lever.

C81349

(f) Align the groove with neutral basic line.

(g) Tighten the 2 bolts.
Torque: 5.4 N
m (55 kgf
cm, 48 in.
lbf)

D25106

(h) Using a screwdriver, stake the nut with the lock washer.

C62669

(i) Install the control lever, washer and nut.

Torque: 13 N
m (130 kgf
cm, 10 ft
lbf)

C81350

U340E A/T REPAIR MANUAL (RM824E)

40–46
AUTOMATIC TRANSMISSION / TRANS – AUTOMATIC TRANSAXLE ASSY (U34#E Series)

164. INSTALL SPEEDOMETER DRIVEN (ATM) GEAR SUB–ASSY

[ 33403G / 3505 ]
165. INSTALL SPEEDOMETER (ATM) SENSOR
[ 83181E / 3505 ]

U340E A/T REPAIR MANUAL (RM824E)