GPS Tracker
Model：R11
User Manual
Statement
Thank you very much for using the R11 vehicle terminal
(mobile user terminal) product. Please read this
manual carefully before use. Please pay attention to all
the cautions and warnings mentioned in the manual.
Please keep this manual properly for reference.
This manual, as well as the description of the software,
can be used or copied directly after receiving the
license, only in accordance with such authority.
The content of this manual is to provide information for
use, subject to change without notice, and should not
be regarded as a commitment by SEEWORLD.
SEEWORLD assumes any liability or any deviation of
legal liability may appear in this book.
SEEWORLD Company reserves the right to make
changes to specifications at any time without notice.
SEEWORLD Corporation believes that this manual is
accurate and reliable. However, SEEWORLD
Corporation is not responsible for its use, or
infringement of patents or the rights of other third
parties caused by its use. Without a license, any patents
or patent rights will belong to SEEWORLD.
Content
1. Product Description ----------------------------------- 3
2. Product Features --------------------------------------- 3
3. Specifications ------------------------------------------- 4
4. Appearance ---------------------------------------------- 5
5. Installation Instrusctions ----------------------------- 6
6. Setting Command Instructions----------------------- 9
7. Installation diagram-----------------------------------11
8. Troubleshooting---------------------------------------11
1.Product Description
The R11 is a multifunctional GPS tracker with a wide
range of applications. Adopts MTK6261 chip and
supports GPS, COMPASS, GLONASS satellite
systems. In addition to supporting satellite
positioning, the equipment also supports
single-base and multi-base station positioning. Rich
extended functions, please refer to the following
descriptions about extended functions. Integrating
a self-developed hardware monitoring circuit
enables the equipment to work reliably and stably
for a long time, and can automatically recover when
an abnormality occurs.
2. Product function
● GSM quad-band, built-in GSM/GPS antenna;
● Support all global navigation satellite systems
GPS, COMPASS, GLONASS, Beidou that have been
deployed and will be in operation
● Support global multi-base station and satellite
positioning mode;
● Voltage input 9-90V;
● Built-in high-power surge protection circuit;
● Adopt high temperature resistant, safe and
explosion-proof rechargeable lithium cobalt oxide
battery;
● Built-in high-power surge protection circuit;
● Built-in hardware monitoring circuit, automatic
recovery of abnormal state;
● Support remote oil circuit control;
● Support ACC detection and alarm;
● Built-in battery switching circuit, support power
failure alarm;
● Built-in vibration sensor, support vibration
alarm;
● Support remote upgrade;
● IP65 waterproof design;
2. Main Function
3. Specification
Items Specifications Remark
Working Voltage DC9V-90V
25ma @12V
Working Current Not charging
(Quiescent current 10mA)
Dimension L80mm *W28mm*H14mm
Positioning mode GPS+LBS+WIFI(Optional)
Positioning error <10 Meters
communication
GPRS
network
GSM frequency 850/900/1800/1900MHz
Communication
TCP
way
Temperature
-25℃~ +75℃
range
Storage
-40℃ ~ +85℃
temperature range
Backup battery
0.5h
working time
Warranty period 1 Year
4. Appearance
By checking the status indicator, you can
understand the working condition of the device.
The status of the indicator is described as follows:
LED
LED Status Description
Color
Fast flash GSM starting
Red Slow flash GPS receive signal is normal
light GPRS online
Drak No GSM signal/card/still sleep
Fast flash GPS signal searching
Blue Light GPS position
Dark GPS sleep/not working
5.Installation instructions
5.1. Wiring
Line No. Specification Color Instruction
8 MOTOR Yellow Fuel control wire
9 ACC White ACC
10 V- Black 12V/24V
Connect to Powe
11 ACC Red of 12V/24V
Precautions for Relay Wiring
Pump relay wiring: the oil connectors at both ends
are thin white wire (85) and thin yellow wire (86).
The thin white wire (85) is connected to the vehicle's
positive power supply (+12V). The thin yellow wire is
connected to the device relay control wire.
Cut off the positive connection wire of the pump;
then connect in series to the relay normally closed
contact (green thick line 87a), and the other end to
the relay COM contact (green thick line 30).
6.Description of command
Instructions
6.1.Oneline Setting Command List
SERVER,1,<domain>,<port># Please move to the
E.g.:SERVER,1,gps. network service
1 whatsgps.com,6801,0# provider service area
APN,<use_apn>#
2 E.g.:APN,internet#
Set APN
T:The range of T is
5-900 second
3 TIMER,T# The default reporting
interval is T second
after setting
6.2. Query command
1 PARAM# Query device parameters
2 STATUS# Set APN
3 WHERE# Query latitude and longitude
4 RESET# evice restart
6.3.Alarm mode setting and description
6. Installation Instruction
A=ON/OFF, turn on or turn
off the alarm, the default
is off
1 Vibration SENALM,A
M=0/1/2, alarm mode, 0:
alarm ,M#
GPRS only; 1: SMS+GPRS;
2: GPRS+SMS+PHONE
A=ON/OFF, turn on or turn
off the alarm, the default is
2 Power off POWERAL off
alarm M,A,M# M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
2: GPRS+SMS+PHONE
A=ON/OFF, turn on or turn
off the alarm, the default
is off
B=1/2/3, 1 is ACC ON
alarm, 2 is ACC OFF alarm,
3 ACC alarm ACCALM,A
3 is ACC ON + ACC OFF
,B,M#
alarm
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
3: GPRS+SMS+PHONE
A=ON/OFF, turn on or turn
off the alarm, the default is
off
R=100-1000, moving
4 Displacemen MOVING,A distance, unit: meter,
t alarm ,R,M# default is 300
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
3: GPRS+SMS+PHONE
A=ON/OFF, turn on or turn
off the alarm, the default is
off
Over speed SPEED,A,
5 alarm B,M#
B=1-255 (Km/h), the
overspeed threshold, the
default is 100 (Km/h)
M=0/1/2, alarm mode, 0:
GPRS only; 1: SMS+GPRS;
3: GPRS+SMS+PHONE
6.4.SOS and Center Number Setting
The SOS number can be
set to 1-3 numbers.
SOS,A,phon Note: When the number
1 SOS setting e1,phone2, already exists, using this
phone3# command will clear the
previously set number and
replace it with a new SOS
number
Center CENTER, Add center number, only
2 number A,phone center number and SOS
setting number# number can be set
6.5.Remote oil cut
When the car speed
reaches below 20KM/H, the
1 Remote oil RELAY,1#
command will be executed
cut
successfully
Remote oil
2 restore
RELAY,0# Restore the oil circuit
7.Installation diagram
8.Trouble shooting
When operating the terminal, if you feel that the
equipment is abnormal, please refer to the
following problems and solutions. If the problem
still cannot be solved, please contact the seller or
service provider.
Common
Reason Solution
Problem
When using the
terminal in areas
with poor signal
reception, such as Use the terminal in
Bad Signal near high-rise a location with
buildings or good signal
basements, radio
waves cannot be
effectively
transmitted
SIM card is not Check the SIM card
installed
Dirt on the metal Wipe with a clean cloth
surface of the SIM
Unable to card
connect to
the network Invalid SIM card Contact your internet
service provider
Out of GSM service Please move to a place
area with strong signal and
try again
Common
Reason Solution
Problem
Unable to Please move to a
connect to Weak signal place with strong
the network signal and try again
Please confirm Turn on the device
whether the device battery switch
is switched on
Switch off Please check if the SIM卡Please install
SIM is installed the SIM card
Poor contact Check if the plug is
connected
Warranty card
Maintenance record
Maintenance shop
Sending date
Fault description
Maintenance situation
IMEI number
Maintenance
person
Maintenance record
Maintenance shop
Sending date
Fault description
Maintenance situation
IMEI number
Maintenance
person
