Hardfacing Products and Guide

We Take the Hard Out of

HARDFACING
TABLE OF CONTENTS

2
EDUCATION...................................................... 4

Introduction.............................................................. 7
Types of Wear .......................................................9
Common Hardfacing Processes ..................... 10
Procedures and Welding Techniques.................... 14
Process Selection................................................ 15
General Guidelines.............................................. 15
General Welding Procedures.................................26
Preheat Recommendations................................... 32

PRODUCTS..................................................... 34

Why Lincoln Electric Hardfacing Alloys................ 35

Hardfacing Product Selection Chart.....................36
Product Selection
Build Up ................................................................38
Metal-to-Metal Wear.........................................44
High Impact / Low Abrasion Wear................. 50
Impact and Abrasion Wear ..............................54
Severe Abrasion / Low Impact Wear............. 56
High Temperature, Corrosion and
Specialty Wear................................................... 64
Submerged Arc Welding Fluxes
for Hardfacing..................................................... 66

RESOURCES...................................................68

Alloy Lot Certification............................................69

Common Package Types ........................................70
Contact.................................................................... 71

HARDFACING PRODUCTS AND GUIDE 3

EDUCATION

4
Benefits of
Hardfacing
Hardfacing is a low cost method of depositing wear
resistant surfaces on metal components to extend
service life. Although used primarily to restore worn
parts to usable condition, hardfacing is also applied
to new components before being placed into service.

In addition to extending the life of new and worn

components, hardfacing provides the following benefits:

•
 Fewer replacement parts needed
• Operating efficiency is increased by
reducing downtime

•
 Less expensive base metal can be used

• Helps reduce overall costs

HARDFACING PRODUCTS AND GUIDE 5

6
 Introduction

Build-up and Hardfacing

Restoring worn parts frequently involves the following three steps:

1. Buttering
For a deposit that will
dilute the carbon and alloy
2. Build-up
S eriously worn areas should
be rebuilt close to working size
3. Hardfacing
 ear resistant surfaces
W
deposited on the base
content of base metal. using tough, crack-resistant metal or on build-up
welding materials which can deposits extend service life.
be deposited in an unlimited Hardfacing is usually limited
number of layers. to two to four layers.

Cladding or Weld Overlay (WOL)

Cladding operations deposit weld metal on the surface of the base material to
extend the service life of the part, while most arc welding processes are used
to join two pieces of base material.
Cladding can be used to enhance the wear resistance or corrosion resistance
of a base material. With cladding, the material deposited is often different
than the base material.

Lincoln Electric offers arc, hot

wire and laser hot wire solutions

for cladding operations.

HARDFACING PRODUCTS AND GUIDE 7
Consumable 1. BASE METAL
Primarily affects the choice of build-up materials
Selection • Manganese steel is used for components subject to high impact
loading. Rebuild to size using manganese steel weld deposits
Choosing a hardfacing consumable
involves the following considerations: • Carbon and alloy steel components are rebuilt to size using low
alloy build-up deposits

• Stainless steel and cast iron base materials may also be addressed
for build-up deposits

2. ARC WELDING METHOD

The choice of arc welding method depends primarily upon the size
and number of the component(s), available positioning equipment and
frequency of hardfacing.
Available methods are as follows:

• Manual Welding using Wearshield® stick electrodes requires the least

amount of equipment and provides maximum flexibility for welding in
remote locations and all positions.

• Semiautomatic Welding uses wire feeders and self-shielded or

gas-shielded, flux-cored Lincore® electrodes increasing deposition
rates over manual welding.

• Automatic Welding requires the greatest amount of initial setup, but

provides the highest deposition rates for maximum productivity. It can
be done with combinations of Lincore® wires and Lincolnweld® submerged
arc flux:
• Neutral flux and alloy wire
• Alloy flux and mild steel wire
• Self-shielded or gas-shielded flux-cored wire used with or without flux

Hardbanding
One example of severe abrasion is specific to the energy segment.
Hardbanding operations deposit a wear-resistant alloy to the surfaces of drill
pipe and drill collars segment drill pipe and drill collars to combat frictional
abrasion between the drill string and casing or the drill string and the earth.

Hardfacing layers are typically added

using advanced and specialized

mechanized handbanding equipment.

8
 Introduction

3. TYPE OF WEAR
The primary consideration in selecting the final hardfacing layers
is the type of wear to be encountered in service.
These include:
Corrosion
Corrosion is often defined as the degradation of a metal by a chemical or
electrochemical reaction with its environment. The effective wear is often a
result of a combination of wear types. Corrosion is commonly addressed by
cladding, often with austenitic stainless steels and nickel-based alloys.

Build-Up
Severely worn areas can be rebuilt close to working size dimensions using tough,
crack-resistant welding materials which can be deposited in an unlimted number
of layers.

Metal-to-Metal Friction
Wear from steel parts rolling or sliding against each other with little or
no lubrication.

Severe Impact
Wear from severe pounding which tends to squash, gouge and crack the surface.
Manganese steel deposits, which work harden in service, provide the greatest
impact wear resistance.

Abrasion Plus Impact

Wear from gritty material accompanied by heavy pounding which tends to chip
or crack, as well as grind, away the surface.

Severe Abrasion
Wear from gritty materials which grind or erode the surface. Severe abrasion is
often accompanied by heavy compression or moderate impact. Hard deposits are
required to resist abrasion but they may also need substantial impact resistance.

Metal-to-Earth Abrasion
Wear from soil or aggregate materials accompanied by moderate impact (pounding).

HARDFACING PRODUCTS AND GUIDE 9

Common Hardfacing
Considerations
FACTORS TO BE CONSIDERED Welding Equipment Type
WHEN SELECTING A SUITABLE
WELDING PROCESS
• What welding equipment is available?
• Is the equipment amperage range adequate for hardfacing?
Process Preference

• Does your equipment or preference lead you to SMAW stick welding,

FCAW-S or FCAW-G semi-automatic welding or SAW mechanized welding?

Consumable Availability

• Do you have a knowledgeable Lincoln Electric technical sales

representative, regional alloy sales specialist or distributor
hardfacing specialist nearby to assist with consumable selection?

Consumable Diameter

• Which SMAW stick or wire diameter is best for your application?

Wire Process Selection

• If wire welding, which wire process is best for your application?
• FCAW-G Gas-shielded wire, FCAW-S open-arc wire or SAW
submerged arc wire?

Operator Skill

• What is the level of your the operator's welding skill, process

knowledge, hardfacing knowledge?

COMMON SMAW (Stick) GTAW (TIG) PTAW (Powder) GMAW (MIG)

HARDFACING Shielded Metal Gas Tungsten Plasma Transferred Gas Metal
PROCESSES Arc Welding Arc Welding Arc Welding Arc Welding

GMAW-C
Gas Metal Arc Welding
with a cored wire

10
 Introduction

Welding Location Machining Requirements

• Are you welding indoors or outdoors? • What are the final surface requirements?
• Is there proper and adequate ventilation • Is machining required? To what resolution?
and/or fume extraction equipment?
Desired Bead Finish
Welded Component Configuration
• Will welding beads be left without grinding
• W
 hat is the size, shape and the area to or machining?
be hardfaced?
• Will the welds be visible?
Deposit Thickness • Are there surface finish requirements
• What is the desired deposit thickness or for appearance?
final dimensions? Component Preparation
Deposition Rate • Have the parts been previously hardfaced?
• Do you have specific production targets that • Is there paint, oil or dirt to be addressed?
determine a target depositon rate?
Preheat And Post Welding Treatments
Welding Position
• Will the part benefit from specific pre and
• Can the component be moved into the flat post heating and cooling practices to achieve
position for welding or must the weldment maximum hardness, maximum service life or
be welded out-of-position? crack resistance?

FCAW FCAW-G SAW HVOF Thermal Arc

Flux-cored Flux-cored Arc Submerged Arc High Velocity Oxygen Spray Process
Arc Welding Welding with a gas- Welding, using a wire Fuel Coating – Typically generating an
shielded wire and flux combination typically used with arc between two wires
FCAW-S a powder or wire
Flux-cored Arc
Welding with a self-
shielded wire

HARDFACING PRODUCTS AND GUIDE 11

Applying the Weld Deposits
1. CLEANLINESS
Remove rust, dirt, grease, oil and other contaminants from the surfaces to be welded.

2. SURFACE PREPARATION
Badly cracked, deformed or work hardened surfaces should be removed by grinding, machining or
carbon-arc gouging.

3. DEPOSIT THICKNESS
Avoid excessive build-up of hardfacing deposits or they may crack and break off rapidly in service.
If thick deposits are needed, use the appropriate build-up materials before hardfacing.

4. PREHEAT AND INTERPASS TEMPERATURE

The combination of alloy content, carbon content, massive size and part rigidity creates a necessity
to preheat in many build-up and hardfacing operations. (See the chart of recommended preheats at
the end of this publication.) Slow cooling may also be needed. Low or minimum preheat, low heat input,
and low interpass temperature are used on Manganese steels.
CAUTION

• Manganese steel becomes brittle if overheated. While a 100°F to 200°F preheat may be required,
do not allow interpass temperatures to exceed 500°F

• Some alloy steel components require a specific heat treatment to perform properly in service.
This must be considered when preheating and welding. Contact the part maker for information

5. DISTORTION
A small amount of distortion can destroy the usability of some parts. Rigid bracing, pre-bending,
skip welding and other distortion control techniques may be required.

6. WELDING PROCEDURES
Obtain the recommended typical operating procedures from the appropriate Lincoln Electric
product literature or from procedures and techniques referenced in this manual. The procedures and
techniques listed are general guidelines for specific applications. Final responsibility must be that of
the builder/user.

12
 Introduction

FUMES AND GASES can be hazardous to your health.

• Fumes from the normal use of this product contain significant quantities of potentially hazardous
compounds. See consumable product label/insert

• Keep your head out of the fumes

• Use enough ventilation and local exhaust to keep fumes and gases from your breathing zone and
the general area

• An approved respirator should be used unless exposure assessments are below applicable
exposure limits

BEFORE USE, READ AND UNDERSTAND THE MATERIAL SAFETY DATA SHEET (MSDS) FOR ANY PRODUCT
AND SPECIFIC INFORMATION PRINTED ON THE PRODUCT CONTAINER.

COMMON HARDFACING TESTING METHODS

Rockwell Scale
The Rockwell Scale is designed to put a score on the measure of penetration
of an ‘indenter’ on a surface. In welding, the Rockwell C scale, noted by Rc,
provides a resulting numeral score. When applied to testing on metals, the Rc
score tends to correlate with tensile strength.

G65 Abrasion Test

The ASTM G65 test is designed to measure sliding abrasion wear on a surface.
In this test, under moderate pressure, dry sand is metered between a rubber
wheel and a block coupon of the hardfaced material under test. The result
is a score for sliding abrasion wear-resistance by measuring the volume loss
of material in cubic millimeters. In this test, the greater the wear resistance,
Rockwell hardness tester the lower the volume loss and resulting score, allowing comparison between
different hardfacing deposits.
HARDFACING PRODUCTS AND GUIDE 13
Procedures and
Welding Techniques

14
Process Selection
MANUAL ELECTRODE WELDING SEMI-AUTOMATIC AND AUTOMATIC WELDING
Recommended: Recommended:
For irregular shapes, out-of-position welding, For large or repeated applications when labor savings
low volume applications, and many small parts. offset equipment costs.

Advantages: Advantages:
1. Highly versatile because it handles: 1. Low weld costs due to high deposition rates and
• Nearly any shape or contour fast welding speeds can enhance production.

• All positions. However, positioning for 2. Consistent weld quality and a smooth
surface are assured by mechanical guidance
downhand welding is recommended
and automatic controls.
• Small or large parts 3. Semiautomatic welding with Lincore self-shielded
• Any deposit pattern electrodes (no granular flux or shielding gas)
2. Inexpensive equipment. Requires only minimum approaches the versatility of stick electrode
fixturing and any conventional welder: rectifier or welding. Lincore gas-shielded flux-cored or metal-
engine driven. DC polarity is recommended, but AC cored wires can typically add greater deposition
can be used with many electrodes. and an improved bead appearance.

Limitations: 4. A lmost any conventional semiautomatic or

automatic welder can be used.
1. L abor costs are relatively high because deposition
rates are lower than mechanized processes. Limitations:
2. Human error can result in poor weld quality or a 1. Welding equipment costs can be substantial.
rough surface. Fixturing is also often required.
2. Submerged arc welding is limited to the flat
position or roundabouts. Its ability to weld contours
and odd shapes is limited.

General Guidelines
Remember, when considering steps to avoid spalling and cracking problems, you are usually
depositing the buildup layer on the base metal and the hardfacing on the buildup metal.

Wearshield Mangjet, Wearshield Wearshield BU, Lincore If underbead cracking becomes a problem
15CrMn, Lincore M and Lincore 15CrMn BU or BU-G, Lincore 30-S, when rebuilding high carbon or other crack-
deposits are manganese steel. Lincore 33 and Lincolnweld sensitive steel, an initial buttering layer with
H-535/L-60 deposits are low Excalibur® 7018, Innershield®NS-3M or mild
carbon, low alloy steel. steel flux and wire may be needed.

HARDFACING PRODUCTS AND GUIDE 15

THE BUILDUP MATERIALS
Some hardfacing deposits have a limited • Buildup Manganese Steel Parts with Wearshield
Mangjet, Wearshield 15CrMn stick electrodes or
practical deposit thickness. Therefore,
Lincore M or Lincore 15CrMn flux-cored wire.
rebuild badly worn parts to within 3/16–3/8
in. (4.8mm–9.5mm) of original size before • Buildup Carbon and Low Alloy Steels with either
Wearshield BU stick electrode, Lincore BU-G,
hardfacing. Lincolnweld H-535 submerged arc flux and L-60,
Choice of the buildup material depends primarily on Lincore 30-S/801 flux or Lincore 33.
the base metal of the part as follows:

PREPARING THE SURFACE

Remove grease and oil with a solvent hardfacing deposits and badly work hardened or
distorted surfaces by arc gouging or grinding. Fill
and rust and dirt by wire brushing.
cracks, gouges and surface depressions by manual
If not removed, these contaminants can cause
welding. Use Wearshield BU or Lincore BU-G on
porosity, cracking and poor deposit quality.
carbon and low alloy steels or Wearshield Mangjet
To provide a good bond between base metal and on manganese steel.
weld, remove cracks, remains of old high alloy

PREHEAT AND INTERPASS TEMPERATURE

Most applications require preheating,
as a minimum to bring the part to room
temperature of 70–100°F.
Medium to high carbon and low alloy steels may
require higher preheat to prevent underbead
cracking, weld cracking, spalling, or stress failure
of the part.
Higher preheat and interpass temperature are
also needed for massive or rigid parts and when
cracking actually occurs. Determine the preheat
necessary for each job by consulting the Preheat
Recommendations table on page 32 of this guide.
NEVER OVERHEAT MANGANESE STEEL.
KEEP INTERPASS TEMPERATURES BELOW
500°F (260°C). Avoid prolonged and concentrated
heat input in any single area. Overheating
manganese steel can lead to a brittle condition.
Surfacing cast iron parts requires special
procedures.

16
 Procedures and Welding Techniques

HOW TO APPLY PREHEAT

Preheating is done with gas or oil Checking the temperature of the part
during welding may be needed to be sure it has
torches, ovens, or electrical heating
not cooled.
devices, depending upon the size of the
Interpass temperature is the temperature of the
part and the equipment available.
surface when welding all layers except the first
It does no good to heat a part, then let it cool layer. It is just as important and should usually
before welding. Always be sure the area to be be as high as the preheat temperature. NEVER
surfaced is at the specified temperature when OVERHEAT MANGANESE STEEL. KEEP INTERPASS
starting to weld. TEMPERATURES BELOW 500°F (260°C).

PATTERN OF DEPOSIT
Using an appropriate bead pattern can help move more material and extend the
equipment life. Here are a few general rules:
• The best pattern is usually the one most • On jobs like crusher rolls, beads placed on the
economical to apply. rolls across the flow of material help pull the

• Since pattern affects shrinkage stresses, material through the rolls.

it can be used to help control distortion and • Beads placed parallel to the flow of abrasive
cracking tendencies. material smooth the flow to reduce wear.

• A pattern with openings between beads is

practical when the openings fill with the
abrasive material in service.

BUILDUP
Badly worn surfaces are normally rebuilt to within 3/16 in. - 3/8 in. (4.8 mm - 9.5 mm)
of original size before hardfacing.

Admixture and Cooling Rate Welding Edges

Small beads made with small electrodes and low Molten metal, slag, and granular submerged arc
currents have fast cooling rates and low admixture flux tends to spill off the edges, particularly when
of base metal into weld metal. Using two layers the part is hot. Eliminate spillage by surfacing
reduces admixture in the final layer. the edges first before the part becomes hot or
else clamp copper bars or flux dams along the
edges. Run beads along the edge rather than
perpendicular to it for smooth welds.

HARDFACING PRODUCTS AND GUIDE 17

TO OBTAIN THE DESIRED WEAR RESISTANCE, CONTROL ALLOY CONTENT AND COOLING RATE
How to Control Alloy Content How to Control Cooling Rate
Carbon and alloy content are controlled by both Although cooling rate affects wear resistance of some
procedures and admixture. Admixture of the deposits, it is much more important for the control of
electrode metal to the base plate has a very spalling, cracking and distortion. Therefore, a slow cooling
important effect on the wear resistance of the rate may be required even if it reduces wear resistance.
weld deposit. Effective weld metal composition Methods of controlling cooling rate include the following:
is listed for deposits having the recommended
number of weld passes. Lincore self-shielded • Preheating is the most effective way of slowing the
cooling rate.
wires and Wearshield stick electrodes produce
consistent weld metal composition despite • Heat input from welding slows cooling by raising the
procedure variations within full normal ranges. temperature of the part.
A single layer of a highly abrasion resistant
material, like Wearshield 60 or Lincore 60-O
• Insulating the hot part immediately after welding with
dry sand, lime, glass fiber blanket, etc. slows cooling.
will not be nearly as abrasion resistant (due This method helps minimize residual cooling stresses,
to dilution) as a second layer. Lincoln® SHS® weld cracking and distortion but does not affect wear
electrodes and wires can produce high abrasion resistance of most deposits. Remember also, large
resistance in the first layer. parts pull heat away from the weld more quickly than
small parts. They naturally cool the weld faster.

Lincore self-shielded

wires and Wearshield

stick electrodes

produce consistent

weld metal composition

despite procedure

variations within full

normal ranges

18
 Procedures and Welding Techniques

TO AVOID WELD SPALLING

Spalling is the breaking of weld metal particles away from the base metal or previous
hardfacing layers. Particle size varies from small chips to large pieces right down to
the base metal. Spalling normally occurs only in service.

1.
Prepare the Surface
2.
Avoid Underbead Cracking
As in production welding, hardfacing welds Rapid cooling from welding temperature can
must have a sound crack-free bond with the cause brittle, crack-sensitive, heat-affected
base metal. Therefore, clean the surface and zones in some types of base metal. These zones
repair cracks and surface damage. tend to crack in service causing spalling. To
avoid this problem, preheat as specified.

3.
Apply a Layer of Austenite
4.
Limit Deposit Thickness
Before Depositing Hardfacing Thick hardfacing deposits build up shrinkage
This can be Type 309 stainless or highly stresses resulting in a greater tendency for
alloyed austenitic manganese, such as spalling. Do not use more hardfacing layers
Wearshield 15CrMn stick electrode or Lincore than specified for each type deposit. If thicker
15CrMn flux-cored wire. Standard austenitic deposits are required, utilize more buildup
manganese, such as Wearshield Mangjet before hardfacing. Peen each layer of thick
stick electrode or Lincore M flux-cored wire, buildup deposits to relieve stresses.
may not provide enough alloy for austenite in
a single layer over carbon or low alloy steel.

HARDFACING PRODUCTS AND GUIDE 19

TO AVOID UNDERBEAD CRACKING
Underbead cracks are small cracks that can occur in the heat affected zone of the
base metal under the weld. The cracks do not usually show on the surface, but can
cause spalling or cracking of the part in service.
Occurrence of underbead cracking depends primarily upon the carbon and alloy content of the base
metal. See the preheat section below for specific preheat recommendations. Use of the non-low
hydrogen electrodes — Wearshield 60, Wearshield ABR and Wearshield MM — may require 100–300°F
(40–150°C) higher preheat than the other Lincoln Electric buildup or hardfacing materials. However,
welding with these electrodes on hot buildup layers usually eliminates potential problems.
The easiest way to prevent underbead cracking is to slow the cooling rate by preheating. Always be
sure the part is at least up to room temperature [70–100°F (20–40°C)] before welding. Use higher
preheats if specified for your particular base metal below. When the base metal analysis is known,
you can determine recommended preheat more closely using the Preheat Calculator available at
lincolnelectric.com
Completing all buildup and hardfacing without long delays is recommended to keep the part hot.
This minimizes danger of cracking and reduces the potential need for additional preheating.
Submerged arc welding, particularly with the Spreadarc™ attachment, is a high heat input process.
It heats the part, slows the cooling rate and reduces underbead cracking problems. Spreadarc is not
recommended on manganese steel.

PREHEAT RECOMMENDATIONS

Low Carbon Steel (to approx. 0.30%C) High Carbon Steel (approx. over 0.45%C)
1. Slightly hardenable. 1.  Highly hardenable and crack sensitive in all
Preheat 70–300°F (21–149°C). sizes and shapes. Preheat to 500–800°F
2. Preheat heavy parts of over .20%C to (260–427°C). Use the higher temperatures for
200–300°F (93–149°C). Use the higher the higher carbon contents and for large, rigid
temperature for massive, rigid or complex parts. or complex shapes.
2. W hen carbon content is near .80%, deposit a
buttering layer with Excalibur 7018 or a mild
Medium Carbon Steel (approx. 0.30 to 0.45%C ) steel submerged arc flux and electrode prior
1. Moderately hardenable, especially in large parts to depositing buildup or hardfacing layers. The
and heavy sections. buttering layer minimizes underbead cracking
2. Preheat to 300–500°F (149–260°C). Use the danger and provides a good bond between base
higher temperature for higher carbon contents metal and hardfacing deposits.
and for large, rigid or complex parts.

20
 Procedures and Welding Techniques

The easiest way to

prevent underbead

cracking is to slow

the cooling rate

by preheating.

Low Alloy Steel Manganese Steel (12-14% Manganese)

1. Varies from medium hardenable to highly 1. Not hardenable or crack-sensitive.
hardenable depending upon carbon and alloy Preheat is not required for thinner sections.
content. Preheat to 100–500°F (38–260°C). 2. Preheat massive or highly rigid parts to
Use the higher temperatures for higher carbon 100–200°F (38–93°C). Prolonged heating over
and alloy contents and for large, rigid or 500°F (260°C) can cause embrittlement of the
complex shapes. manganese steel.
2. Preheat temperatures up to 800°F (427°C) or 3. On small parts, avoid high localized heating by
a buttering layer may be required if the carbon using a skip welding technique.
content is over .35%C.

Cast Iron
Extremely crack sensitive. The heat-affected zone may be full of cracks even with preheat temperatures
of 1200–1400°F (650–760°C). Therefore, hardfacing cast iron is often uneconomical. If it must be welded,
follow the standard cast iron welding precautions in Lincoln Electric Publication C8.10.

HARDFACING PRODUCTS AND GUIDE 21

TO AVOID STRESS FAILURE OF THE PART
Some parts contain high retained internal stresses. Stress failure can be avoided with the following steps:
When the welding stresses are added to these retained 1. Preheat slowly to the high side of the temperature range as
stresses, the part can break. This is stress failure. previously specified for the particular type of base metal. As
Such failure can occur near the weld or at any weak much as possible, this preheat should be uniform throughout
point in the part. Look for this possibility when the part.
hardfacing the following types of parts: • Shrink-fit parts must be preheated to expand them until
• Highly rigid parts. Massive parts and complex shapes they are loose. Manganese steel requires a lower
are inherently rigid temperature because it has a high coefficient of expansion

• Shrink-fit parts • Parts which were hardened by heat treatment should be

• Some large castings, particularly when they are pack or controlled atmosphere annealed. Slow cool until
the specified preheat temperature is reached
made of medium to high carbon steel or medium
carbon low alloy steels 2. A rrange the welding schedule so it can be completed without

• Parts hardened by heat treatment any interruptions.

3. The part should be slowly and uniformly cooled. This can be
done by covering the part with a glass fiber blanket or some
other insulating material or by cooling in a furnace.

22
 Procedures and Welding Techniques

TO AVOID WELD CRACKING—PRODUCTS DESIGNED FOR BUILD-UP

Lincoln Electric hardfacing products designed for buildup applications have good resistance to cross
cracking and are not restricted with regard to deposit thickness. These products include Wearshield BU,
Lincore BU-G, Lincore M, Lincore 30-S with 801 flux, Lincore 33, Wearshield 15CrMn, Lincore 15CrMn and
Lincolnweld H-535/L-60 (low alloy procedure).
Special precautions, however, should be taken with any buildup or hardfacing product on applications
that are inherently crack sensitive. These applications include the surfacing of high carbon or alloy steels,
previously surfaced parts and highly stressed parts. The surfacing of heavy cylinders, massive parts and
parts having complex shapes are all examples of applications producing high internal stresses that may
result in delayed cracking.

• These applications may require one or more of the following precautions:

• Higher preheat temperature [400–500°F (200–260°C)]
• Higher interpass temperatures
• Controlled slow cooling between passes and/or layers and after completion of the welding
• Minimizing layer thickness. Very severely stressed parts may require an intermittent or final drawing
operation at 800–900°F (427–482°C)

TRANSVERSE OR CROSS CRACKING LONGITUDINAL OR CENTER-LINE CRACKING

The third and sometimes the second Wearshield This cracking is associated with poor bead shape. It is caused by ta concave
ABR or Lincore 50 layer and all “Severe Abrasion” bead shape, that is, a high ratio of bead height to bead width.
type deposits are designed to cross crack. This is If Center-Line Cracking is a Problem:
beneficial because the cracking relieves stresses
which can otherwise cause spalling or distortion. • When welding with stick or Lincore flux-cored electrodes, use a stringer
This cross cracking does not harm the wear bead or minimum weaving technique and low current
resistance of the deposit. • Be sure fillet welds are slightly convex
In other types of deposits, cross cracking can be • In submerged arc surfacing when using Spreadarc attachment, center-line
a problem. It generally occurs in parts which are cracking does not often occur. This is because the high heat input of the
massive, rigid or of complex shape. If this cross process assures sufficiently slow cooling
cracking must be minimized, preheat to 1200°F
(650°C). The preheating found necessary to
• In other submerged arc jobs this cracking can sometimes occur. If it does,
decrease the step-over (or increase the bead overlap) enough to remelt
prevent underbead or stress failure cracking will the center of the previous bead, or adjust bead shape
also minimize weld cross cracking.
• For submerged arc jobs on roundabouts, be sure you set the correct
electrode displacement distance and angle

HARDFACING PRODUCTS AND GUIDE 23

 TO AVOID DISTORTION PROBLEMS
Distortion in welding is caused principally by the unbalanced stresses which result
from the expansion of the metal during heating and contraction during cooling.
These stresses and their effects are uneven both in strength and direction. They
depend on many factors.
In many cases the small amount of resultant distortion does not affect the performance of the part.
Consequently, no more precaution than clamping the part in position for welding is needed. In some
cases the part is hardfaced oversize to allow for the distortion. It is then machined or ground to size.
This method is most often used on parts which must be machined or ground to finish before using.
In some cases the part is allowed to distort, and it is straightened while still hot enough to bend
without cracking.
In those cases where the distortion will ruin the usability of the part, the distortion forces must be
controlled. Use one or a combination of the following methods. Generally, a study of the part to be
surfaced and the equipment available will determine the best method to use.

CROSS-CRACKING DEPOSIT

24
 Procedures and Welding Techniques

Methods of Controlling Distortion:

1. Preforming
Use with flat pieces and other relatively thin and simply shaped parts.
• Bend, form, or clamp the part with the proper preset before welding. The distortion forces will
then pull the part back to its original shape

2.  Counterbalance the Stresses

Use with parts which cannot be straightened after welding. Be sure the increased rigidity will not
cause underbead cracking.
• Weld or clamp two similar parts back to back. Alternate the welding from one part to the other
• Weld or clamp the part to a strongback, fixture or platen
3. Limit the Temperature of the Part
This is an effective method, particularly when high rigidity can cause cracking.
• Distribute the heat evenly by first welding one area, then welding a different area as the first cools
• Reduce the heat input by using a procedure with low current
• Remove some of the heat by blowing air, circulating water through the part, or clamping a water-
cooled copper jacket to the part
• Substitute properly welded inserts rather than making thick welds
4. R
 elieve the Stresses
Stress relieve very large parts, rigid shapes, shrink-fit parts, and other highly stressed pieces
• Peen each layer during cooling. This is most effective with Severe Impact and Abrasion-plus-Impact-
type deposits
• Preheat the entire part slowly and uniformly to expand the part prior to welding. Generally
150–200°F (66–93°C) is sufficient for manganese steel. Preheat carbon or low alloy steel to
300–500°F (149–260°C)

5. Cross-Cracking Deposit
The “Severe Abrasion” type deposits are designed to cross crack on cooling. These cracks
minimize distortion by relieving the stresses.

HARDFACING PRODUCTS AND GUIDE 25

General Welding Procedures

26
 General Welding Procedures

MANUAL COVERED ELECTRODES

There is an optimum TABLE 1

current for every Electrode Size in. (mm) 3/32 (2.4) 1/8 (3.2) 5/32 (4.0) 3/16 (4.8) 1/4 (6.4)

application. Use
DC+/AC (Amps) 80–100 90–165 140–220 175–260 210–325
this guide to help
Deposition Rate 1.2–2.0 (.54–.90) 2.1–2.8 (.95–1.3) 2.7–3.8 (1.2–1.7) 3.7–5.0 (1.7–2.3) 4.9–6.9 (2.2–3.1)
lb/Hr (kg/hr)
find the best setting

for a particular Wearshield hardfacing electrodes metal dripping. Wide weaves are not
may be used on flat, vertical and recommended with any hardfacing
Wearshield electrode
sometimes overhead surfaces. In the electrodes and, in particular, not
and application. flat position, the excellent Wearshield with manganese steel electrodes or
arc operation will permit weaving the base metals.
electrode up to 1/2 in. (12.7mm) wide. As in any welding type, proper plate
When welding on vertical surfaces, preparation is necessary for good
deposit a stringer bead along the results. Small diameter electrodes and
bottom of the area to be surfaced low currents are recommended when
and build on that bead to cover the welding on manganese steel castings.
entire surface. Overhead applications Procedures and techniques that will
require smaller diameter electrode, prevent overheating the manganese
low operating currents and special base plate are necessary to prevent
welding techniques to prevent weld cracking spalling, and embrittlement.

LINCORE® OPEN ARC SELF-SHIELDED ELECTRODES

Table 2 lists typical TABLE 2 - LINCORE TYPICAL OPERATING PROCEDURES
Direct Current Electrode Positive (DC+) 1
parameters for the
Electrode Size in. (mm) .045 (1.1) 1/16 (1.6) 5/64 (2.0) 7/64 (2.8)
Lincore Open Arc

Electrodes. WFS in/min (m/min) 200–600 (5.1–15.2) 150–450 (3.8–11.4) 125–250 (3.2–6.4) 90–175 (2.3–4.4)

Amps 85–250 125–350 190–400 280–420

Volts 21–31 24–33 25–32 26–32

ESO in. (mm) 3/4 –1-1/8 (19–29) 7/8–1-3/4 (22–45) 1-1/4–1-3/4 (32–45) 1-1/2–2-3/4 (38–70)

Deposition Rate 3.6–12.3 (1.5–5.6) 4.8–16.6 (2.2–7.5) 7.0–15.1 (3.2–6.9) 8.4–16.5 (3.8–7.5)
lb/Hr (kg/hr)

Melt-Off Rate lb/Hr (kg/hr) 4.3–13.1 (2.0–5.9) 5.9–17.4 (2.7–7.9) 8.0–15.8 (3.6–7.2) 10.6–19.6 (4.8–8.9)

Individual electrode sheets contain the previous bead top surface until 1
Constant voltage
power supplies are
precise information relative to the area to be surfaced is covered. recommended but
constant current may
procedure and deposition rates. Small Lincore semiautomatic electrodes also be used.
diameter Lincore semiautomatic are designed for optimum operator
electrodes can be used on vertical appeal and require no external
surfaces by depositing a stringer shielding. It is possible to use these
bead along the bottom of the area to electrodes with Lincolnweld 801 or 802
be surfaced. A copper chill bar may flux for a further reduction in smoke
be necessary to support this bead. and spatter.
Subsequent beads are deposited along
HARDFACING PRODUCTS AND GUIDE 27
LINCORE OPEN ARC SELF-SHIELDED TABLE 3 - OPERATING CHARACTERISTICS
ELECTRODES OPERATING CHARACTERISTICS
Increasing Wire Feed Increasing Voltage Increasing Electrical Decreasing Electrical
When Lincore electrodes are used properly, Speed (amps) (volts) Stickout (ESO) Stickout (ESO)
the resulting smooth, uniform weld bead is
Increases Wider and Increases Excessively
fully covered (except Lincore 50, 60-O and 65-O), Deposition Rate Flatten Bead Melt-Off Rate Short Stickout
Results in Porosity
with easily removed slag and depositions rates Increases Excessive Voltage Excessively
Penetration Results in Porosity Long Stickout
are significantly higher than with manual Results in
Increases Increased Spatter
(stick) welding. Heat Input

LINCORE SUBMERGED ARC ELECTRODES TABLE 4 - TYPICAL PARAMETERS

A good starting point for general operating

procedures when welding with submerged arc Electrode Size in. (mm) 3/32 (2.4) 1/8 (3.2) 5/32 (4.0)

flux and the Lincore electrodes would be in the WFS in/min (m/min) 50–140 (1.3–3.6) 48–90 (1.2–2.3) 40–65 (1.0–1.7)
middle of the operating range.
Amps 250–450 350–625 475–800

Volts 25–28 26–30 26–30

ESO in. (mm) 1-1/4 (32) 1-1/2 (38) 1-1/2 (38)

Deposition Rate 6.5–17.5 (2.9–8.0) 9.5–22.1 (4.3–10.0) 13.1–27.3 (6.0–12.4)

lb/Hr (kg/hr)
Melt-Off Rate 6.6–17.8 (3.0–8.1) 9.7–22.6 (4.4–10.3) 13.4–27.9 (6.1–12.7)
lb/Hr (kg/hr)

28
 General Welding Procedures

CIRCUMFERENTIAL SUBMERGED ARC HARDFACING

In circumferential hardfacing, 3 in. (76mm) To prevent spilling or bead distortion, the weld
diameter and larger cylindrical objects are rotated must freeze as it passes the vertical center of
under the welding head. The welds differ from the work. This requires the proper electrode
those made in the flat position in that the flux and displacement distance as listed in Table 6 and the
molten metal tends to sag or spill off the work. proper wire feed speed and voltage from Table 4.
Speed must also be controlled to make small beads
of the proper shape.

A faster, smaller bead

tends to freeze quicker

than a slow bead.

HARDFACING PRODUCTS AND GUIDE 29

TEMPERATURE CONTROL TABLE 5

The temperature of the work should be kept below 700°F (370°C) for easy
Electrode Position 'd' (Inches Ahead
slag removal and control of spilling. In addition to depositing small beads and Girth Diameter in. (mm) of Vertical Center) in. (mm)
using air jets or internal water cooling (when practical), temperature can be
3–18 (76–457) 3/4–1 (19–25)
controlled by depositing a stringer bead.
18–36 (457–914) 1-1/4– 1-1/2 (31–38)

APPROXIMATE 36–48 (914–1219) 1-1/2–2 (38–51)

DISPLACEMENT (D) d
OF THE ELECTRODE 48–72 (1219–1828) 2.0–2-1/2 (51–63)

over 72 (1824) 2.0–2-1/2 (51–63)

Rotation

NEUTRAL HARDFACING FLUX CHARACTERISTICS

Lincolnweld® 880 Lincolnweld 801 Lincolnweld 802
The fine mesh size is Darker in color, larger mesh Use with electrodes containing
economical to use. Use size. Use with most hardfacing Ti, V, Cb, Mo or W alloys.
with most hardfacing semiautomatic and automatic May be used in place
semiautomatic and automatic Lincore electrodes. of 801 flux.
Lincore electrodes.

30
 General Welding Procedures

OVERLAP OVERLAP WELDING CURRENTS & VOLTAGES

The amount that one bead overlaps the adjacent bead affects both admixture
of base metal into weld metal — greater overlap reduces admixture — and Diameter in. (mm) Current (amps)
appearance of the finished weld. Control overlap by adjusting the amount of
3–6 (76–152) 250–350 1
longitudinal travel with each revolution.
6–12 (76–304) 300–400
Longitudinal travel is accomplished either by spiraling the bead or indexing
the welding head across the work after each complete revolution (stepover). 12–18 (304–457) 350–500
Unless a lathe with a slow screw feed mechanism or a very low speed travel
std. hardfacing procedures
carriage is available, the stepover method is recommended. over 18 (457) (single electrode or
Twin-Arc®)
For automatic stepover, mount a limit switch that is operated by a cam type
trip on the rotating fixture. Connect the limit switch into the travel carriage 1
Voltage Range is 24-32 volts.
motor circuit so the motor runs when the switch is operated. The distance
moved is controlled by the size of the cam and speed of the travel motor. A
time delay can be used in place of the cam. Slag must be removed before each
bead makes a complete revolution.

HARDFACING PRODUCTS AND GUIDE 31

Preheat
Recommendations

Preheat Temperature °F (°C)-

Steel Group Organization Steel Designation Carbon Level Base Metal
4 in (101.6 mm) Thick 1
1015 0.13–0.18 150 (66)
1020 0.18–0.23 150 (66)
Carbon Steels AISI-SAE 1030 0.28–0.34 200 (93)
1040 0.37–0.44 300 (149)
1080 0.75–0.88 600 (316)
1330 0.28–0.33 250 (161)
1335 0.33–0.38 300 (149)
Carbon-Manganese Steels AISI-SAE 1340 0.38–0.43 350 (177)
1345 0.43–0.48 400 (204)
1345H 0.42–0.49 400 (204)
4027H 0.24–0.30 250 (121)
2032H 0.29–0.35 300 (149)
Molybdenum Steels AISI-SAE 4037H 0.34–0.41 350 (177)
4042H 0.39–0.46 400 (204)
4047H 0.44–0.51 450 (232)
4118 0.17–0.23 250 (121)
4130 0.27–0.34 300 (149)
Chrome Molybdenum Steels AISI-SAE 4135 0.32–0.39 400 (204)
4145 0.41–0.49 500 (260)
4145H 0.42–0.49 500 (260)
4340 0.38–0.43 500 (260)
4615 0.18–0.18 250 (121)
Ni-Chrome Molybdenum 4620 0.17–0.22 250 (121)
AISI-SAE
& Ni-Moly Steels
4720H 0.17–0.23 300 (149)
4820H 0.17–0.23 300 (149)

1
These suggested preheats are recommended when Low “The steels shown on the chart are only partially
Hydrogen processes are used on base metals that are 4" thick. representative of the steels used in the manufacture of earth
Lower preheats could be used on thinner material while higher moving and other machinery. A Preheat Calculator
preheats would be necessary on thicker materials. When using available from The Lincoln Electric Co. makes it possible to
non-Low Hydrogen processes increase suggested preheats by figure suggested preheats for other steels based upon the
300°F (149°C). chemistry of the steel and the thickness of
the parts to be surfaced.”

32
 Preheat Recommendations

Preheat Temperature °F (°C)-

Steel Group Organization Steel Designation Carbon Level Base Metal
4 in (101.6 mm) Thick 1
5015 0.12–0.17 200 (93)
5046 0.43–0.48 450 (232)
Chromium Steels AISI-SAE 5115 0.13–0.18 200 (93)
5145 0.43–0.48 450 (232)
5160 0.56–0.64 550 (288)
11-14% Mn 0.5–1.3 Preheat only to remove chill
from base material
302 0.15 Max
Austenitic Manganese & ASTM
Chrome-Ni Steels 2 309 0.20 Max
310 0.25 Max
347 0.08 Max
A36 0.27 Max 250 (121)

Carbon Steel Plate - A131 Gr. B 0.21 Max 200 (93)

ASTM
Structural Quality A284 Gr. C 0.29 Max 250 (121)
A678 Gr. B 3 0.20 Max 200 (93)
A131-H.S. 0.18 Max 350 (177)
A242 Type 2 0.20 Max 200 (93)
High Strength
Low Alloy Steels – ASTM A441 0.22 Max 200 (93)
Structural Quality
A588 Gr. B 0.20 Max 300 (149)
A633 Gr. E 0.22 Max 250 (121)
A514 Gr. F (3) 0.10–0.21 350 (177)
A514 Gr. H (3) 0.12–0.21 300 (149)
Alloy & Pressure ASTM A514 Gr. Q (3) 0.14–0.21 550 (288)
Vessel Quality Steels
A514 Gr. 70 0.35 Max 300 (149)
A514 Gr. 70 0.30 Max 250 (121)

2
“It is sometimes advisable to preheat large, thick 11 to 14%
Manganese parts prior to welding. Use a maximum of 200°F.
preheat. (Do not exceed 500°F (260°C) interpass temperature).
Check base metal with magnet. 11 to 14% Manganese and the
ASTM 300 series of chrome-nickel steels are NOT magnetic.”
3
Q & T Steels

HARDFACING PRODUCTS AND GUIDE 33

PRODUCTS

34
Why Lincoln Electric Alloys
Sourcing Alloy Consumables from Lincoln Electric is a smart choice.

LEADING QUALITY CONTROL PROVEN PERFORMANCE ADVANTAGES

Our standard manufacturing Quality Assurance • Less downtime due to lower contact tip wear
System includes some checks other suppliers
simply do not perform:
• Greater arc stability resulting from more
constant feed force
• A full time steel analyst works closely with the • Less spatter made possible with more
mill to verify that mill output matches Lincoln controlled chemical composition
Electric tolerances

• Our specs on incoming green rod from the mill WELDABILITY

are tighter than AWS requirements Customer testing confirms great operator
• We test each end of every coil of green rod, ratings for:
ensuring consistency in product chemistry,
mechanical properties and operation
• Puddle control
• Edge wetting
• An Optical Electron Spectrometer tests each • Bead appearance
incoming sample for 30 chemical elements

• X-Ray Flourescence tests verify proper A SOLUTIONS BASED APPROACH

surface treatment
As a comprehensive welding supplier, Lincoln
Electric can supply a complete system that, used
CONSISTENT ARC CHARACTERISTICS
together, delivers better results — faster travel
Attention to quality translates directly into speeds, lower spatter, better bead appearance,
stable, consistent behavior at the arc: control over burnthrough
• Feeding • Premium welding wire
• Placement • Modular, adaptable welding equipment
• Surface treatment • Welding waveform-driven processes like
• Hydrogen levels Rapid X®, Surface Tension Transfer® (STT®)

AVAILABLE CUSTOM FORMULATIONS

• Robotic systems
FOR YOUR APPLICATION • Additive manufacturing, press automation, tube
bending, laser systems, plasma cutting systems
Do you seek a wire to address changing and more
materials? New qualifications? Poor fitup?
Faster travel speeds? Talk to us. We can help. • Fume control, personal protection equipment
and welding education

HARDFACING PRODUCTS AND GUIDE 35

Hardfacing
Product Offering

BUILD UP METAL-TO-METAL HIGH IMPACT/ LOW ABRASION

FCAW-G FCAW-G FCAW-G

Lincore BU-G Lincore 55-G Lincore M
Lincore M7-G
FCAW-S FCAW-S
Lincore BU FCAW-S Lincore 15CrMn
Lincore 33 Lincore 40-O Lincore FROG MANG®
Lincore 55 Lincore Super Rail™
SMAW Lincore T&D
Wearshield BU SMAW
SMAW Wearshield Mangjet
SAW Wearshield MI Wearshield 15CrMn
Lincore 30-S
SAW Wearshield FROG MANG
Lincore 20
Lincore 40-S Wearshield Super Rail
Lincore 4130
Lincore 42-S
Lincore 32-S Lincore 102W
Lincore 35-S Lincore 102HC IMPACT AND ABRASION
Lincore 410
Lincore 410NiMo FCAW-S
Lincore 420
Lincore 50
Lincore 420-S
Lincore 57-G
Lincore 423CR-S
Lincore 420HC-S
SMAW
Lincore 423Cr
Lincore 423L Wearshield 44
Lincore 423N Wearshield ABR
Lincore 96-S
Wearshield ME

36
 Hardfacing Product Offering

SEVERE ABRASION/LOW IMPACT SPECIALTY

FCAW-S FCAW-S Cobalt, Nickel Filler Metals, Hardfacing Fluxes

Lincore Ticore Lincoln® Guardian™ CF
COBALT SMAW NEUTRAL FLUX
Lincore Ultra K Lincoln Guardian HB
Lincoln SHS® 9192U Lincoln WT-1 Lincolnweld 801®
GMAW-C Lincoln SHS 9500U Lincoln WT-12 Lincolnweld 802™
Lincore 60-G Lincoln SHS 9700U Lincoln WT-21 Alloy Flux
Lincore 70-G Lincoln SHS 9800U Lincoln WT-6
FLUX
FCAW-S PTAW COBALT GTAW Lincolnweld H-560™
Lincoln SHS 9290P
Lincore 60 Lincoln WT-1 Lincolnweld A-96-S
Lincore 65-0 SMAW Lincoln WT-12 Lincolnweld H-535™
Lincoln SHS 9700E Lincoln WT-21
SMAW
Lincoln SHS 9800E Lincoln WT-6
Wearshield 60 Blue Max 2100
SMAW
THSP HVOP
Blue Max® 2100
Lincoln SHS 7574HV
Lincoln SHS 8000HV
Lincoln SHS 9172HV

WIRE ARC SPRAY

Lincoln SHS 7570W
Lincoln SHS 8000W
Lincoln SHS 9172W

HARDFACING PRODUCTS AND GUIDE 37

Build Up Consumables
Welding wires and electrodes classified as Build Up are ideal for ‘building up’ or adding dimension to tools
made of carbon and low alloy steels. Typically, Build up consumables are used as an underlying pass or layer
on carbon steel parts prior to applying a hardfacing pass or layer. Build up consumables are typically designed
to exhibit good compressive strength under heavy loading. Build up weld deposits are generally crack free,
machinable and can be flame cut. Deposit thickness for build up consumables is often unlimited.

CATEGORY INDUSTRY
Rockwell
Hardness (Rc )
Sub-Category Sub-Category As-Welded Chemical General Heavy Maintenance Power
Build Up Metal-To-Metal Caster Rolls Product Family (Work Hardened) Processing Fabrication Fabrication and Repair Generation Structural

78–90
Lincore BU (86–98)
(Rockwell R B)

1 Layer:
14–30 (28–34),
2 Layers:
Lincore 33 26–32 (32–36),
3 Layers:
25–34 (35–38)

As Welded:
Lincore BU-G 21–33 (40–42)

1 Layer: 15–20
2 Layers: 18–23
Wearshield BU
3 Layers: 23–28

38
 Build Up Product Selection

APPLICATIONS

Dia. Pkg Wt.

Common Use Weld Process Part Number In (mm) lbs (kg) Package Type Flux/ Gas Weld Position

ED031115 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal

ED022064 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal

Crane, Kiln, Mine Car,
FCAW-S
Shovel, Rolls, Tractor
ED022065 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal

ED022069 7/64 (2.8) 125 (11.3) Accutrak Drum Flat, Horizontal

ED011237 5/64 (2.0) 14 (6.4) Coil Flat, Horizontal

ED031116 0.045 (1.1) 25 (11.3) Steel Spool Flat, Horizontal

Undercarriage parts, Bark, Bucket,
Crane, Crusher Hammer, Cutter &
Teeth, Drag, Drums, Ingot, Kiln, ED031117 1/16 (1.6) 25 (11.3) Steel Spool Flat, Horizontal
Loader, Logging, Mine Car/Wheel, FCAW-S
Mix, Open Hearth, Plate, Rail, Roll,
Shovel, Tractor ED031118 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal

ED011238 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal

ED011240 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal

ED029079 0.045 (1.1) 25 (11.3) Plastic Spool Flat, Horizontal

75-90%
Bark, Crane, Cutter & Teeth, Kiln, Argon/
Roll, Plate, Loader, Logging, Mine FCAW-G ED037318 1/16 (1.6) 50 (22.7) Fiber Spool Balance Flat, Horizontal
Car/Wheel, Open Hearth, Shovel, CO2; 98%
Drums, Rail, Tractor Argon/2% O2
ED029080 1/16 (1.6) 25 (11.3) Plastic Spool Flat, Horizontal

Bark, Crane, Cutter & Teeth, Kiln, ED021991 5/32 (4.0) 10 (4.5) Carton Flat, Horizontal
Roll, Plate, Loader, Logging, Mine SMAW
Car/Wheel, Open Hearth, Shovel,
Drums, Rail, Tractor ED021993 3/16 (4.8) 10 (4.5) Carton Flat, Horizontal

HARDFACING PRODUCTS AND GUIDE 39

 CATEGORY INDUSTRY
Rockwell
Hardness (Rc )
Sub-Category Sub-Category As-Welded Chemical General Heavy Maintenance Power
Build Up Metal-To-Metal Caster Rolls Product Family (Work Hardened) Processing Fabrication Fabrication and Repair Generation Structural

6 layers w/801
or 802:
Lincore 30-S 27
(Metal-cored)
6 layers w/860:
27

Lincore 20 23–28
(Metal-Cored)

Lincore 4130 23–28

(Metal-Cored)

Lincore 8620 16–20

(Metal-Cored)

2 Layers w/802:
28,
Lincore 32-S
2 Layers on 4140
w/802: 33

Lincore 35-S 39

40
 Build Up Product Selection

APPLICATIONS

Dia. Pkg Wt.

Common Use Weld Process Part Number In (mm) lbs (kg) Package Type Flux/ Gas Weld Position
Flat, Horizontal,
ED011200 3/32 (2.4) 50 (22.7) Coil Circumferential

Crane, Cut/Teeth, Ingot, Kiln, Roll, Flat, Horizontal,

ED015889 1/8 (3.2) 50 (22.7) Coil
Logging, Mine Car, Shovel, Rail, Circumferential
Lincolnweld
Shovel, Tractor SAW 801, 802
600 Speed-Feed® Flat, Horizontal,
ED011199 3/32 (2.4) (272.2) Drum Circumferential

600 Speed-Feed® Flat, Horizontal,

ED015891 1/8 (3.2) (272.2) Drum Circumferential

Flat, Horizontal,
EDS18565 3/32 (2.4) 50 (22.7) Coil Circumferential

Crane, Cut/Teeth, Ingot, Kiln, Roll, Flat, Horizontal,

EDS18566 1/8 (3.2) 50 (22.7) Coil
Logging, Mine Car, Shovel, Rail, Circumferential
SAW Lincolnweld
Shovel, Tractor 801, 802
600 Speed-Feed® Flat, Horizontal,
ED018569 1/8 (3.2) (272.2) Drum Circumferential

600 Speed-Feed® Flat, Horizontal,

EDS18570 5/32 (4.0) (272.2) Drum Circumferential

Flat, Horizontal,
ED015265 3/32 (2.4) 50 (22.7) Coil Circumferential

Used for 4130 type rolls , Crane, Kiln, Flat, Horizontal,

ED015266 1/8 (3.2) 50 (22.7) Coil
Mine Car/Wheel, Rail, Roll, Shovel, Circumferential
Lincolnweld
Tractor SAW 801, 802
600 Speed-Feed® Flat, Horizontal,
ED015532 3/32 (2.4) (272.2) Drum Circumferential

600 Speed-Feed® Flat, Horizontal,

ED015405 1/8 (3.2) (272.2) Drum Circumferential

Flat, Horizontal,
ED020788 50 (22.7) Coil Circumferential
Used for 8620 type rolls, Crane, Kiln, Lincolnweld
SAW
Roll, Mine Car, Shovel, Tractor 801, 802
600 Speed-Feed® Flat, Horizontal,
ED020791 (272.2) Drum Circumferential

Speed-Feed® Flat, Horizontal,

Build up on 4140 drill stems, Brake/ ED025656 3/32 (2.4) 300 (136.1) Drum Circumferential
Lincolnweld
Drum, Crane, Kiln, Mine Car, Rail, Roll, SAW 802
Shovel, Tractor 600 Speed-Feed® Flat, Horizontal,
ED025131 1/8 (3.2) (272.2) Drum Circumferential

Flat, Horizontal,
ED019880 3/32 (2.4) 50 (22.7) Coil Circumferential

Flat, Horizontal,
ED019881 1/8 (3.2) 50 (22.7) Coil Circumferential

Crane, Ingot, Kiln, Mine Car, Shovel, 600 Speed-Feed® Lincolweld Flat, Horizontal,
SAW ED019883 3/32 (2.4)
Rail, Shovel, Tractor (272.2) Drum 801, 802 Circumferential

600 Speed-Feed® Flat, Horizontal,

ED019884 1/8 (3.2) (272.2) Drum Circumferential

600 Speed-Feed® Flat, Horizontal,

ED019885 5/32 (4.0) (272.2) Drum Circumferential

HARDFACING PRODUCTS AND GUIDE 41

Metal-to-Metal
Products in this category are low alloy steels designed for rebuilding of carbon or low alloy parts
used in applications involving non-lubricated rolling or sliding metal-tometal wear. These high impact
hardfacing products offer good compressive strength, hardness and wear resistance for build up or
overlay. Not intended to be used as an underbase for subsequent hardfacing. Proper preheat and
interpass temperatures can help make the application of multiple layers easy.

CATEGORY INDUSTRY

Rockwell Hardness
Metal-To- Sub-Category: (Rc) As-Welded Chemical General Heavy Maintenance Power
Metal Caster Rolls Product Family (Work Hardened) Processing Fabrication Fabrication and Repair Generation Structural

Lincore 102HC 54–60

Lincore 102W 48–54

1 Layer: 36,
Lincore 40-O 2 Layers: 41,
3 Layers: 38

3 or more
Lincore 40-S Layers: 39-42

Lincore 410 27–32

42
 Metal-to-Metal Product Selection

APPLICATIONS

Weld Dia.
Common Use Process Part Number In (mm) Pkg Wt. lbs (kg) Package Type Flux/ Gas Weld Position

Auger, Bar, Blade, Blast Furnance, Flat,Horizontal,

ED026085 1/8 (3.2) 50 (22.7) Coil
Blower, Bucket, Bulldozer, Circumferential
Cement, Coke, Crush, Cut, Door,
Drag, Dredge, Hammer, Hoist, Kiln,
Speed-Feed® Lincolnweld 802, Flat,Horizontal,
Mill, Mine Car, Mix, Mixer, Pipe SAW ED026086 3/32 (2.4) 600 (272.2) Drum 801 Circumferential
Bend, Pipeline, Plate, Plow, Power
Generation, Pump, Rail, Roll, Sand,
Scrape, Screen, Shovel, Sinter, Speed-Feed® Flat,Horizontal,
Tamper, Teeth, Tractor, Wheel ED026087 1/8 (3.2) 600 (272.2) Drum Circumferential

Flat,Horizontal,
ED018578 1/8 (3.2) 50 (22.7) Coil Circumferential
Speed-Feed® Flat,Horizontal,
Brake, Crane, Drive, ED018580 3/32 (2.4) 600 (272.2) Drum Lincolnweld 802, Circumferential
Extrusion, Mill, Pump, Drum, SAW 801 Flat,Horizontal,
Roll, Shovel, Tractor ED018581 1/8 (3.2) 600 (272.2) Coil Circumferential
Speed-Feed® Flat,Horizontal,
ED018582 5/32 (4.0) 600 (272.2) Drum Circumferential

ED031119 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal

Bark, Bucket, Crane, Crush,
Drag, Drive, Hammer, Ingot,
Kiln, Logging, Mine Car, Mix,
FCAW-S ED025907 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal
Open Hearth, Power, Power
Generation, Rail, Roll, Shovel,
Teeth, Tractor, Wheel
ED025907 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal

Bark, Bucket, Crane, Crush, Flat,Horizontal,

ED015892 1/8 (3.2) 50 (22.7) Coil
Drag, Drive, Hammer, Ingot, Circumferential
Kiln, Logging, Mine Car, Mix,
SAW
Open Hearth, Power, Power
Generation, Rail, Roll, Shovel, Speed-Feed® Lincolnweld 802, Flat,Horizontal,
Teeth, Tractor, Wheel ED015909 1/8 (3.2) 600 (272.2) Drum 801 Circumferential

Flat,Horizontal,
Brake, Crane, Drive, Drum, ED018583 3/32 (2.4) 50 (22.7) Coil Circumferential
Extrusion, Kiln, Mine Car, Power
SAW
Generation, Rail, Roll, Shovel,
Tractor, Wheel Speed-Feed® Lincolnweld 802, Flat,Horizontal,
ED018588 5/32 (4.0) 600 (272.2) Drum 801 Circumferential

HARDFACING PRODUCTS AND GUIDE 43

 CATEGORY INDUSTRY

Rockwell Hardness
Metal-To- Sub-Category: (Rc) As-Welded Chemical General Heavy Maintenance Power
Metal Caster Rolls Product Family (Work Hardened) Processing Fabrication Fabrication and Repair Generation Structural

Lincore 32–40
410NiMo

Lincore 42-S 1 Layer: 40

Lincore 420-S 46–50

Lincore 51–55
420HC-S

Lincore 423Cr-S 41–47

Lincore 423L 41–47

Lincore 423N

Lincore 423N-G

44
 Metal-to-Metal Product Selection

APPLICATIONS

Weld Dia.
Common Use Process Part Number In (mm) Pkg Wt. lbs (kg) Package Type Flux/ Gas Weld Position
Flat, Horizontal,
ED018589 3/32 (2.4) 50 (22.7) Coil Circumferential
Flat, Horizontal,
ED018590 1/8 (3.2) 50 (22.7) Coil Circumferential
Brake, Crane, Drive, Drum,
Extrusion, Kiln, Mine Car, Power Lincolnweld Flat, Horizontal,
SAW EDS18591 5/32 (4.0) 50 (22.7) Coil
Generation, Rail, Roll, Shovel, 802, 801 Circumferential
Tractor, Wheel
Speed-Feed® Flat, Horizontal,
ED018593 1/8 (3.2) 600 (272.2) Drum Circumferential
Speed-Feed Flat, Horizontal,
ED018594 5/32 (4.0) 600 (272.2) Drum Circumferential

Auger, Brake, Crane, Drive, Speed-Feed Lincolnweld Flat, Horizontal,

Drum, Extrusion, Kiln, Mill, Mine ED029264 1/8 (3.2) 1/8 (3.2) Drum 802, 801 Circumferential
Car, Power , Power Generation,
SAW
Pulverizer, Rail, Roll, Scarrifier,
Shovel, Teeth, Tractor, Speed-Feed Lincolnweld Flat, Horizontal,
ED029161 1/8 (3.2) 600 (272.2)
Wearplate, Wheel Drum 802, 801 Circumferential

Flat, Horizontal,
ED037238 3/32 (2.4) 50 (22.7) Spool Circumferential

Brake, Crane, Drive, Drum, Speed-Feed Flat, Horizontal,

ED037239 3/32 (2.4) 600 (272.2)
Extrusion, Kiln, Mine Car, Power Drum Circumferential
Lincolnweld
SAW
Generation, Rail, Roll, Shovel, 802, 801 Flat, Horizontal,
Tractor, Wheel ED037271 1/8 (3.2) 50 (22.7) Spool Circumferential
Speed-Feed Flat, Horizontal,
ED037272 1/8 (3.2) 600 (272.2) Drum Circumferential

Flat, Horizontal,
ED037315 3/32 (2.4) 50 lb (22.7) Coil Circumferential
Flat, Horizontal,
Caster rolls and backup rolls ED037313 1/8 (3.2) 50 lb (22.7) Coil
Lincolnweld Circumferential
when water spray causes pitting SAW
Speed-Feed 802, 801 Flat, Horizontal,
on tool steel deposits ED037314 3/32 (2.4) 600 (272.2) Drum Circumferential
Speed-Feed Flat, Horizontal,
ED037312 1/8 (3.2) 600 (272.2) Drum Circumferential

Speed-Feed Flat, Horizontal,

ED018557 1/8 (3.2) 600 (272.2)
Drum Circumferential

Brake, Crane, Drive, Drum,

Extrusion, Kiln, Car, Power Speed-Feed Flat, Horizontal,
SAW ED037273 1/8 (3.2) 600 (272.2) Lincolnweld 802
Generation, Rail, Roll. Shovel, Drum Circumferential
Tractor, Wheel

Brake, Crane, Drive, Drum,

Extrusion, Kiln, Mine Car, Power Flat, Horizontal,
SAW ED018551 1/8 (3.2) 600 (272.2) Lincolnweld 802
Generation, Rail, Roll, Shovel, Circumferential
Tractor, Wheel

Flat, Horizontal,
ED036012 1/8 (3.2) 50 lb (22.7) Spool
Brake, Crane, Drive, Drum, Power Circumferential
SAW Lincolnweld 802
Generation, Rail, Roll Speed-Feed Flat, Horizontal,
ED036013 1/8 (3.2) 600 (272.2) Drum Circumferential

Flat, Horizontal,
ED037543 1/16 (1.6) 25 (11.3) Spool
Brake, Crane, Drive, Drum, Power Circumferential
SAW Lincolnweld 802
Generation, Rail, Roll Speed-Feed Flat, Horizontal,
ED037544 1/16 (1.6) 450 (204.1) Drum Circumferential

HARDFACING PRODUCTS AND GUIDE 45

 CATEGORY INDUSTRY

Rockwell Hardness
Metal-To- Sub-Category: (Rc) As-Welded Chemical General Heavy Maintenance Power
Metal Caster Rolls Product Family (Work Hardened) Processing Fabrication Fabrication and Repair Generation Structural

1 Layer:
50–59
(53–62),
Lincore 55
2 Layers:
50–60
(56–62)

1 Layer:
50–51
2 Layers:
Lincore 55-G 53–54
4 Layers:
54–55

1 Layer:
50–51
2 Layers:
Lincore M7-G 53–54
4 Layers:
54–55

Lincore 96-S 48–54

48–55,
Lincore T & D Tempered at 540°C
(1000°F): 55–65

1 Layer:
50
Wearshield MI
2 or More Layers:
54

46
 Metal-to-Metal Product Selection

APPLICATIONS

Weld Dia.
Common Use Process Part Number In (mm) Pkg Wt. lbs (kg) Package Type Flux/ Gas Weld Position
Coil/Master
ED012777 5/64 (2.0) 14 (6.4)/56 (25.4) Flat, Horizontal
Carton
Bark, Blade, Blower, Brake,
ED031120 0.045 (1.2) 25 (11.3) Steel Spool Flat, Horizontal
Crane, Crush, Drag, Drive, Drum,
Exevate, Extrusion, Hammer, ED031121 1/16 (1.6) 25 (11.3) Steel Spool Flat, Horizontal
Ingot, Kiln, Loader, Logging,
FCAW-S ED031122 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal
Mill, Mine Car, Mix, Open
Hearth, Plate, Power, Power
Generation,Rail, Roll, Shovel, ED011278 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal
Sinter, Teeth, Tractor, Wheel ED011280 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal
ED037254 0.045 (1.2) 10 (4.5) Flat, Horizontal

ED036444 0.045 (1.1) 10 (4.5) Plastic Spool Flat, Horizontal,

Vertical
Flat, Horizontal,
ED028176 0.045 (1.1) 25 (11.3) Plastic Spool Vertical
Flat, Horizontal,
ED028177 1/16 (1.6) 25 (11.3) Plastic Spool
Bark, Blade, Blower, Brake, Vertical
Crane, Crush, Drag, Drive, Drum, Flat, Horizontal,
Exevate, Extrusion, Hammer, ED031475 0.045 (1.1) 500 (226.8) Accu-Trak® Drum 75-90% Argon/ Vertical
Ingot, Kiln, Loader, Logging, Balance CO 2
FCAW-G
Mill, Mine Car, Mix, Open 98% Argon/ Flat, Horizontal,
ED032661 1/16 (1.6) 500 (226.8) Accu-Trak® Drum
Hearth, Plate, Power, Power 2% O 2 Vertical
Generation,Rail, Roll, Shovel,
Sinter, Teeth, Tractor, Wheel Flat, Horizontal,
ED037409 0.045 (1.1) 25 (11.3) Plastic Spool Vertical

Flat, Horizontal,
ED037410 0.045 (1.1) 500 (226.8) Accu-Trak® Drum Vertical

Flat, Horizontal,
ED037525 1/16 (1.6) 200 (90.7) Accu-Trak® Drum Vertical

ED037470 1/16 (1.6) 25 (11.3) Plastic Spool Flat, Horizontal,

Bark, Blade, Blower, Brake, Vertical
Crane, Crush, Drag, Drive, Drum,
Exevate, Extrusion, Hammer, 75-90% Argon/ Flat, Horizontal,
ED037476 0.045 (1.1) 25 (11.3) Plastic Spool
Ingot, Kiln, Loader, Logging, Balance CO 2 Vertical
FCAW-G
Mill, Mine Car, Mix, Open 98% Argon/ Flat, Horizontal,
Hearth, Plate, Power, Power ED037477 0.045 (1.1) 50 (22.7) Coil 2% O 2 Vertical
Generation,Rail, Roll, Shovel,
Sinter, Teeth, Tractor, Wheel Flat, Horizontal,
ED037565 1/16 (1.6) 50 (22.7) Coil Vertical

Speed-Feed® Flat, Horizontal,

ED018574 3/32 (2.4) 600 (272.2) Drum Circumferential
Crane, Drive, Extrusion, Kiln, Mine
Speed-Feed® Lincolnweld Flat, Horizontal,
Car, Power Generation, Rail, Roll, SAW ED018575 1/8 (3.2) 600 (272.2) Drum 802, 801 Circumferential
Shovel, Tractor, Wheel
Speed-Feed® Flat, Horizontal,
ED018576 5/32 (4.0) 600 (272.2) Drum Circumferential

Auger, Brake, Crane, Drive, Drum, ED031134 1/16 (1.6) 25 (11.3) Steel Spool Flat, Horizontal
Extrusion, Kiln, Mill, Mine Car, Ore,
Power Generation, Pulverizer, FCAW-S
Rail, Roll, Scarrifier, Shovel, Teeth,
Tractor, Wearplate, Wheel ED037818 1/16 (1.6) 50 (22.7) Fiber Spool Flat, Horizontal

Flat, Horizontal,
ED022003 1/8 (3.2) 10 (4.5) Carton Overhead
Brake, Bucket, Concrete, Crane, Flat, Horizontal,
Drive, Drum, Extrusion, Mix, Pump, SMAW ED022005 5/32 (4.0) 10 (4.5) Carton Overhead
Rails, Roll, Shovel, Teeth, Tractor
Flat, Horizontal,
ED022007 3/16 (4.8) 10 (4.5) Carton Overhead

HARDFACING PRODUCTS AND GUIDE 47

High Impact/Low Abrasion
High Impact / Low Abrasion wires and electrodes are austenitic manganese alloys that produce tough, high-
strength weld deposits that work harden under impact. These products are typically used for joining, repairing
or building up manganese steel parts that are joined together, or for joining manganese to carbon steel.
Common applications include railroad frogs, impact hammers, rotors and rock crusher rolls. Deposit thickness
for many of these High Impact / Low Abrasion consumables is unlimited and the deposit can be flame cut.

CATEGORY INDUSTRY
Rockwell
Hardness (Rc)
Abrasion & As-Welded (Work Chemical General Heavy Maintenance Power
Impact Product Family Hardened) Processing Fabrication Fabrication and Repair Generation Structural

Lincore 15CrMn 18–22 (40–50)

Lincore FROG MANG® 18–22 (40–50)

Lincore M 18–28 (30–48)

Lincore Super Rail™ N/A

48
 High Impact/ Low Abrasion Product Selection

APPLICATIONS

Dia.
Common Use Weld Process Part Number In (mm) Pkg Wt. lbs (kg) Package Type Weld Position

ED031126 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal

ED022060 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal

Bar, Bucket, Crush, Cut, Drag,
Dredge, Hammer, Mix, Open
Hearth, Plate, Power Generation, FCAW-S ED022061 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal
Pump, Rail, Roll, Screen, Shovel,
Teeth, Wheel
ED022068 7/64 (2.8) 125 (11.3) Speed-Feed® Drum Flat, Horizontal

ED037492 1/16 (1.6) 33 (14.9) Steel Spool Flat, Horizontal

Plastic Spool/
ED034485 5/64 (2.0) 9 (4.1), 36 (16.3) Flat, Horizontal
Master Carton

Railroad Frog Tracks FCAW-S ED026106 1/16 (1.6) 25 (11.3) Steel Spool Flat, Horizontal

ED026105 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal

ED031128 0.045 (1.1) 25 (11.3) Steel Spool Flat

ED031129 1/16 (1.6) 25 (11.3) Steel Spool Flat

ED031130 5/64 (2.0) 25 (11.3) Steel Spool Flat

Bar, Bucket, Crush, Cut, Drag,
Dredge, Hammer, Mix, Open
Hearth, Plate, Power Generation, FCAW-S ED011160 5/64 (2.0) 50 (22.7) Coil Flat
Pump, Rail, Roll, Screen, Shovel,
Teeth, Wheel
ED011164 7/64 (2.8) 50 (22.7) Coil Flat

ED011163 7/64 (2.8) 125 (56.7) Speed-Feed Drum Flat

ED011162 7/64 (2.8) 600 (272.2) Speed-Feed Drum Flat

ED035353 1/16 (1.6) 36 (16.3) Carton Flat, Horizontal

ED034800 5/64 (2.0) 36 (16.3) Carton Flat, Horizontal

Rail FCAW-S
ED035354 1/16 (1.6) 25 (11.3) Spool Flat, Horizontal

ED034801 5/64 (2.0) 25 (11.3) Spool Flat, Horizontal

HARDFACING PRODUCTS AND GUIDE 49

 CATEGORY INDUSTRY
Rockwell
Hardness (Rc)
Abrasion & As-Welded (Work Chemical General Heavy Maintenance Power
Impact Product Family Hardened) Processing Fabrication Fabrication and Repair Generation Structural

Wearshield 15CrMn 18–24 (40–50)

Wearshield FROG MANG® 20–30 (40–50)

Wearshield Mangjet® 2 Layers: 18 (47)

Wearshield Super Rail™ N/A

50
 High Impact/ Low Abrasion Product Selection

APPLICATIONS

Dia.
Common Use Weld Process Part Number In (mm) Pkg Wt. lbs (kg) Package Type Weld Position

Flat, Horizontal,
ED021980 1/8 (3.2) 10 (4.5) Carton Overhead
Bar, Bucket, Crush, Cut, Drag,
Dredge, Hammer, Mix, Open
Flat, Horizontal,
Hearth, Plate, Power Generation, SMAW ED021982 5/32 (4.0) 10 (4.5) Carton Overhead
Pump, Rail, Roll, Screen, Shovel,
Teeth, Wheel
Flat, Horizontal,
ED021984 3/16 (4.8) 10 (4.5) Carton Overhead

Flat, Horizontal,
ED033134 5/32 (4.0) 10 (4.5) Carton Overhead
Bar, Bucket, Crush, Cut, Drag,
Dredge, Hammer, Mix, Open
Flat, Horizontal,
Hearth, Plate, Power Generation, SMAW ED033135 3/16 (4.8) 10 (4.5) Carton Overhead
Pump, Rail, Roll, Screen, Shovel,
Teeth, Wheel
Flat, Horizontal,
ED033133 1/4 (6.4) 36 (16.3) Carton Overhead

Flat, Horizontal,
ED021976 5/32 (4.0) 50 (22.7) Carton Overhead
Bar, Bucket, Crush, Cut, Drag,
Dredge, Hammer, Mix, Open
Flat, Horizontal,
Hearth, Plate, Power Generation, SMAW ED021978 3/16 (4.8) 50 (22.7) Carton Overhead
Pump, Rail, Roll, Screen, Shovel,
Teeth, Wheel
Flat, Horizontal,
ED021979 1/4 (6.4) 50 (22.7) Carton Overhead

Rail SMAW ED035352 3/16 (4.8) 10 (4.5) Can Flat, Horizontal

HARDFACING PRODUCTS AND GUIDE 51

Impact and Abrasion
Products in this category are iron-based chromium carbide alloys designed for applications subject
to abrasion accompanied by impact from rock, ore, clay, sand or cement, including digging or
crusher surfaces or parts that must maintain sharp cutting edges. These products can be applied
in multiple layers and may cross check crack. Metal-to- Earth hardfacing products can be used on
carbon, low alloy, manganese, stainless and cast iron parts.

CATEGORY INDUSTRY
(Sub) Rockwell
Severe Hardness (Rc) Mass
Abrasion As-Welded Loss
Abrasion & Metal-To- (Work (ASTM Chemical General Heavy Maintenance Power
Impact Earth Product Family Hardened) G-65) Processing Fabrication Fabrication and Repair Generation Structural

1 Layer: 42, 2
Wearshield 44 Layers: 47, 4
Layers: 48

1 Layer:
34–37, 2
Layers:
Lincore 50 44–48, 3
Layers:
48–52

Lincore 57-G 56–59 0.36

1 Layer:
24–53, 2
Wearshield ABR
Layers:
28–53

1 Layer: 49, 2
Wearshield ME Layers: 59, 3
Layers: 59

52
 Impact and Abrasion Product Selection

APPLICATIONS

Weld Dia. Pkg Wt. lbs

Common Use Process Part Number In (mm) (kg) Package Type Flux/ Gas Weld Position

Auger, Bar, Blade, Bucket,

ED024940 1/8 (3.2) 10 (4.5)/40 Carton/ Flat, Horizontal
Bulldozer, Concrete, Crush, Cut, (18.1) Master Carton
Cut, Drag, Dredge, Hammer, Hoist,
Ingot, Kiln, Mine Car, Mix, Pipeline, SMAW
Plate, Plow, Power Generation,
Pump, Roll, Scrape, Shovel, Shred, Carton/
ED024941 5/32 (4.0) 10 (4.5) Flat, Horizontal
Master Carton
Teeth, Teeth, Tractor, Wheel

ED031123 0.045 (1.1) 25 (11.3) Steel Spool Flat, Horizontal

ED031124 1/16 (1.6) 25 (11.3) Steel Spool Flat, Horizontal

Auger, Bar, Blade, Bucket, ED031125 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal
Bulldozer, Concrete, Crush, Cut,
Cut, Drag, Dredge, Hammer, Hoist, ED017825 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal
Ingot, Kiln, Mine Car, Mix, Pipeline, FCAW-S
Plate, Plow, Power Generation, ED011275 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal
Pump, Roll, Scrape, Shovel, Shred,
Teeth, Teeth, Tractor, Wheel ED011274 7/64 (2.8) 125 (56.7) Speed-Feed Drum Flat, Horizontal

ED037261 1/16 (1.6) 10 (4.5) Plastic Spool Flat, Horizontal

ED037270 0.045 (1.1) 10 (4.5) Plastic Spool Flat, Horizontal

Auger, Bar, Blade, Blast Furnance, ED037297 1/16 (1.6) 10 (4.5) Plastic Spool Flat, Horizontal
Blower, Bucket, Bulldozer,
Cement, Coke, Crush, Cut, Door,
Drag, Dredge, Hammer, Hoist, Kiln,
75-90Ar/
Mill, Mine Car, Mix, Mixer, Pipe GMAW-C ED037298 1/16 (1.6) 25 (11.3) Plastic Spool Flat, Horizontal
Bal CO 2
Bend, Pipeline, Plate, Plow, Power
Generation, Pump, Rail, Roll, Sand,
Scrape, Screen, Shovel, Sinter,
Tamper, Teeth, Tractor, Wheel ED037296 1/16 (1.6) 500 (227) Accu-Trak Drum Flat, Horizontal

Auger, Bar, Blade, Bucket, 10 (4.5)/40 Carton/ Flat, Horizontal,

ED021996 1/8 (3.2) (18.1) Master Carton Vertical, Overhead
Bulldozer, Concrete, Crush, Cut,
Cut, Drag, Dredge, Hammer, Hoist,
10 (4.5)/40 Carton/ Flat, Horizontal,
Ingot, Kiln, Mine Car, Mix, Pipeline, SMAW ED021996 5/32 (4.0) (18.1) Master Carton Vertical, Overhead
Plate, Plow, Power Generation,
Pump, Roll, Scrape, Shovel, Shred,
10 (4.5)/40 Carton/ Flat, Horizontal,
Teeth, Teeth, Tractor, Wheel ED022000 3/16 (4.8) (18.1) Master Carton Vertical, Overhead

10 (4.5)/40 Carton/
Auger, Bar, Blade, Bucket, ED023323 1/8 (3.2) Flat, Horizontal
(18.1) Master Carton
Bulldozer, Concrete, Crush, Cut,
Cut, Drag, Dredge, Hammer, Hoist,
Ingot, Kiln, Mine Car, Mix, Pipeline, SMAW 10 (4.5)/40 Carton/
ED023324 5/32 (4.0) Flat, Horizontal
(18.1) Master Carton
Plate, Plow, Power Generation,
Pump, Roll, Scrape, Shovel, Shred,
Teeth, Teeth, Tractor, Wheel 10 (4.5)/40 Carton/
ED023325 3/16 (4.8) Flat, Horizontal
(18.1) Master Carton

HARDFACING PRODUCTS AND GUIDE 53

Severe Abrasion/Low Impact
Products in this category are iron-based with a large amount of chromium carbides in a
hard matrix. These alloys are designed for severe sliding abrasion accompanied by low
or moderate impact. These products are designed to exhibit stress-relieved cross-check
cracking. They can be used on carbon, low alloy, manganese, stainless and cast iron
parts. Deposit thicknesses are generally limited to two to four layers.

CATEGORY INDUSTRY
(Sub) Severe
Severe Abrasion Rockwell
Abrasion/ Metal-To- Hardness Mass Loss Chemical General Heavy Maintenance Power
Low Impact Earth Product Family (Rc) (ASTM G-65) Processing Fabrication Fabrication and Repair Generation Structural

Lincore 70-G 60-70

(Metal-Cored)

Lincore 60-O 55–60

1 Layer: 57, 2
Lincore 65-O Layers: 60, 4
Layers 64

Lincore Ticore 57–64

Lincore Ultra K™ 56–62

54
 Severe Abrasion/Low Impact Product Selection

APPLICATIONS

Dia. Pkg Wt.

Common Use Weld Process Part Number In (mm) lbs (kg) Package Type Flux/ Gas Weld Position

ED036455 0.045 (1.1 ) 10 (4.5) Plastic Spool Flat, Horizontal

ED029936 0.045 (1.1 ) 12 (5.4) Plastic Spool Flat, Horizontal

Auger, Bar, Blade, Blast Furnance,
Blower, Bucket, Bulldozer, ED037243 0.045 (1.1 ) 10 (4.5) Plastic Spool Flat, Horizontal
Cement, Coke, Crush, Cut, Door,
Drag, Dredge, Hammer, Hoist, Kiln, ED037244 0.045 (1.1 ) 33 (14.9) Plastic Spool Flat, Horizontal
75-90Ar/
Mill, Mine Car, Mix, Mixer, Pipe GMAW-C Bal CO 2
Bend, Pipeline, Plate, Plow, Power ED037245 1/16 (1.6) 10 (4.5) Plastic Spool Flat, Horizontal
Generation, Pump, Rail, Roll, Sand,
Scrape, Screen, Shovel,Sinter,
Tamper, Teeth, Tractor, Wheel ED037246 1/16 (1.6) 33 (14.9) Plastic Spool Flat, Horizontal

ED037247 3/32 (2.3) 33 (14.9) Plastic Spool Flat, Horizontal

ED037248 7/64 (2.8) 55 (24.9) Coil Flat, Horizontal

ED031131 0.045 (1.1 ) 25 (11.3) Steel Spool Flat, Horizontal

ED031132 1/16 (1.6) 25 (11.3) Steel Spool Flat, Horizontal

Auger, Bar, Blade, Blast Furnance,
Blower, Bucket, Bulldozer, ED031133 5/64 (2.0) 25 (11.3) Steel Spool Flat, Horizontal
Cement, Coke, Crush, Cut, Door,
Drag, Dredge, Hammer, Hoist, Kiln, ED037262 0.045 (1.1 ) 10 (4.5) Steel Spool Flat, Horizontal
Mill, Mine Car, Mix, Mixer, Pipe FCAW-S
Bend, Pipeline, Plate, Plow, Power ED037263 1/16 (1.6) 10 (4.5) Steel Spool Flat, Horizontal
Generation, Pump, Rail, Roll, Sand,
500 SpeedFeed®
Scrape, Screen, Shovel,Sinter, ED037493 5/64 (2.0) Flat, Horizontal
(2226.8) Drum
Tamper, Teeth, Tractor, Wheel
ED019887 5/64 (2.0) 50 (22.7) Coil Flat, Horizontal

ED019888 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal

Auger, Bar, Blade, Blast Furnance, ED026076 1/8 (3.2) 50 (22.7) Coil Flat, Horizontal
Blower, Bucket, Bulldozer,
Cement, Coke, Crush, Cut, Door,
Drag, Dredge, Hammer, Hoist, Kiln, ED026077 7/64 (2.8) 50 (22.7) Coil Flat, Horizontal
Mill, Mine Car, Mix, Mixer, Pipe FCAW-S
Bend, Pipeline, Plate, Plow, Power 500 SpeedFeed®
ED026082 1/8 (3.2) Flat, Horizontal
Generation, Pump, Rail, Roll, Sand, (2226.8) Drum
Scrape, Screen, Shovel,Sinter, 500 SpeedFeed®
Tamper, Teeth, Tractor, Wheel ED026083 7/64 (2.8) Flat, Horizontal
(2226.8) Drum

Crush, Hammer, Plate, Wheel FCAW-S ED035628 5/64 (2.0) 25 (11.3) Coil Flat, Horizontal

600 SpeedFeed®
Auger, Crush, Hammer, Plate, Wheel FCAW-S ED034802 1/8 (3.2) Flat, Horizontal
(272.2) Drum

HARDFACING PRODUCTS AND GUIDE 55

 CATEGORY INDUSTRY
(Sub) Severe
Severe Abrasion Rockwell
Abrasion/ Metal-To- Hardness Mass Loss Chemical General Heavy Maintenance Power
Low Impact Earth Product Family (Rc) (ASTM G-65) Processing Fabrication Fabrication and Repair Generation Structural

Lincore Ultra R™

1 Layer:
57–60,
Wearshield® 60 2 Layers:
60–62

Lincoln Guardian CF 58–62 0.22

FE GRIP

Lincoln Guardian™ HB 57–59 0.32

Lincoln SHS 0.2

Lincoln SHS 7574HV 0.13

Lincoln SHS 8000HV 0.07

Lincoln SHS 8000W 0.18

Lincoln SHS 9172HV

0.07

Lincoln SHS 9172W 0.17

Blue Max 2100

56
 Severe Abrasion/Low Impact Product Selection

APPLICATIONS

Dia. Pkg Wt.

Common Use Weld Process Part Number In (mm) lbs (kg) Package Type Flux/ Gas Weld Position
SpeedFeed®
ED035367 1/8 (3.2) 50 (22.7) Flat, Horizontal
Drum
Auger, Crush, Hammer, Plate, Wheel FCAW-S
500 SpeedFeed®
ED035368 1/8 (3.2) Flat, Horizontal
(2226.8) Drum

Auger, Bar, Blade, Blast Furnance,

ED022010 1/8 (3.2) 10 (4.5) Carton Flat, Horizontal
Blower, Bucket, Bulldozer, Cement,
Coke, Crush, Cut, Door, Drag, Dredge,
Hammer, Hoist, Kiln, Mill, Mine Car,
Mix, Mixer, Pipe Bend, Pipeline, SMAW ED022011 5/32 (4.0) 10 (4.5) Carton Flat, Horizontal
Plate, Plow, Power Generation,
Pump, Rail, Roll, Sand, Scrape,
Screen, Shovel, Sinter, Tamper,
ED022012 3/16 (4.8) 10 (4.5) Carton Flat, Horizontal
Teeth, Tractor, Wheel

Flat, Horizontal,
Hardbanding applications FCAW-S ED035668 1/16 (1.6) 33 (15) Spool Circumferential

Flat, Horizontal,
ED037597 1/16 (1.6) 25 (11.3) Circumferential
Paper, power Gent, Pulp, Wheel THSP ASP
400 Flat, Horizontal,
ED037598 1/16 (1.6) (181.4) Circumferential

Flat, Horizontal,
Hardbanding applications FCAW-S ED035667 1/16 (1.6) 33 (15) Spool Circumferential

Paper, Power,
Wire Arc Spray ED035664 1/16 (1.6) 25 (11.3) Spool PLW N/A
Power generation, Pulp

Mine Car, Paper, Power, Power

THSP HVOF ED035730 +15/-35 25 (11.3) Pail N/A
generation, Pulp, Wheel

ED35732 +15/-35 10 (4.5) Bottle N/A

Mine Car, Paper, Power, Power
THSP HVOF
generation, Pulp, Wheel
ED035733 +15/-35 25 (11.3) Bottle N/A

ED035665 1/16 (1.6) 25 (11.3) Spool N/A

Tubes, Pulp, Paper Wire Arc Spray
400
ED035972 1/16 (1.6) SpeedFeed Drum N/A
(181.4)

ED035734 +15/-35 10 (4.5) Bottle N/A

Mine Car, Paper, Power, Power
THSP HVOF
generation, Pulp, Wheel
ED035735 +15/-35 25 (11.3) Bottle N/A

Screen, Paper, Power,

Wire Arc Spray ED035666 1/16 (1.6) 25 (11.3) Spool PLW N/A
Power Generation, Pulp

ED032298 3/32 (2.3) 10 (4.5) Can Flat, Horizontal

Auger, Cruah, Hammer, Join, Plate, SMAW
Pulp & paper, Chemical, Power Gen
ED032299 1/8 (3.2) 10 (4.5) Can Flat, Horizontal

HARDFACING PRODUCTS AND GUIDE 57

 CATEGORY INDUSTRY
(Sub) Severe
Severe Abrasion Rockwell
Abrasion/ Metal-To- Hardness Mass Loss Chemical General Heavy Maintenance Power
Low Impact Earth Product Family (Rc) (ASTM G-65) Processing Fabrication Fabrication and Repair Generation Structural

Lincoln SHS 9192U

Lincoln SHS 9700P 71–74 0.08

SHS 9294P

Lincoln SHS® 9500U 58–62 0.22

Lincoln SHS 9700E 67–70 0.13

Lincoln SHS 9700U 67–70 0.13

Lincoln SHS 9800U 68–71 0.12

Lincoln SHS 9800E

58
 Severe Abrasion/Low Impact Product Selection

APPLICATIONS

Dia. Pkg Wt.

Common Use Weld Process Part Number In (mm) lbs (kg) Package Type Flux/ Gas Weld Position
ED035663 0.045 (1.1) 33 (15) Spool Flat, Horizontal
ED037277 1/16 (1.6) 30 (13.6) Spool Flat, Horizontal
ED037278 1/16 (1.6) 400 (181) SpeedFeed Drum Flat, Horizontal
ED035661 3/32 (2.4) 55 (25) Coil Flat, Horizontal
Auger, Crush, Hammer, Plate FCAW-S ED035660 7/64 (2.8) 55 (25) Coil Flat, Horizontal
ED037595 1/16 (1.6) 50 (22.7)
500
ED037614 3/32 (2.4) (226.8)
500
ED037615 7/64 (2.8) (226.8)

Crush, Hammer, Plate PTAW ED035724 +15/-180 10 (4.5) Bottle Flat, Horizontal
ED035725 +15/-180 25 (11.3) Bottle Flat, Horizontal

Crush, Hammer, Plate PAW ED037599 +15/-180 10 (4.5) Bottle Flat, Horizontal

Screen, Paper, Power , ED035749 0.045 (1.1) 33 (15) Spool Flat, Horizontal
FCAW-S
Power Generation, Pulp ED037275 1/16 (1.6) 45 (20) Fiber Spool Flat, Horizontal

Screen, Paper, Power , ED035669 5/32 (4.0) 10 (4.5) Carton Flat, Horizontal
SMAW
Power Generation, Pulp ED037653 1/8 (3.2) 10 (4.5) Carton Flat, Horizontal

ED037276 1/16 (1.6) 33 (15) Spool Flat, Horizontal

ED035658 0.045 (1.1) 33 (15) PLW Spool Flat, Horizontal
ED035657 1/16 (1.6) 33 (15) Spool Flat, Horizontal
ED035655 3/32 (2.4) 55 (25) Spool Flat, Horizontal
Screen, Paper, Power, ED035654 7/64 (2.8) 55 (25) Coil Flat, Horizontal
FCAW-S
Power Generation, Pulp
400
ED037594 1/16 (1.6) SpeedFeed Drum Flat, Horizontal
(181.4)
500
ED037616 3/32 (2.4) SpeedFeed Drum Flat, Horizontal
(226.8)
500
ED035857 7/64 (2.8) SpeedFeed Drum Flat, Horizontal
(226.8)

ED035650 0.045 (1.1) 25 (11.3) Spool Flat, Horizontal

ED035648 1/16 (1.6) 33 (15) Spool Flat, Horizontal
ED035858 1/16 (1.6) 50 (22.7) Spool Flat, Horizontal
ED035646 3/32 (2.4) 55 (25) Coil Flat, Horizontal
ED035645 7/64 (2.8) 55 (25) Coil Flat, Horizontal
Auger, Crush, Hammer,
FCAW-S
Plate, Power Generation ED035859 1/16 (1.6) 400 SpeedFeed Drum Flat, Horizontal
500
ED035860 3/32 (2.4) SpeedFeed Drum Flat, Horizontal
(226.8)
500
ED035924 7/64 (2.8) SpeedFeed Drum Flat, Horizontal
(226.8)

ED035973 7/64 (2.8) 280 (127) SpeedFeed Drum Flat, Horizontal

ED037651 5/32 (4.0) 10 (4.5) Can Flat, Horizontal

Auger, Crush, Hammer,
SMAW
Plate, Power Generation
ED037652 1/8 (3.2) 10 (4.5) Can Flat, Horizontal

HARDFACING PRODUCTS AND GUIDE 59

Submerged Arc Welding Fluxes for Hardfacing
Lincoln Electric granular submerged arc flux is designed to produce sizeable weld deposits with exceptional
quality and bead appearance on a variety of flat and horizontal welding applications, including general
fabrication, offshore, wind tower pressure vessel and maintenance and repair activities like hardfacing.
Great attention is paid to the details in manufacturing including exhaustive quality control over consistent
chemistry and particulate size.

CATEGORY INDUSTRY

Rockwell Hardness (Rc )

As-Welded Chemical General Heavy Maintenance Power
Flux Product Family (Work Hardened) Processing Fabrication Fabrication and Repair Generation Structural

Lincolnweld A-96-S Range 48-54

Lincolnweld 801® See Wire

Lincolnweld 802™ Range 24-45

Lincolnweld H-535™ Range 52-61

Lincolnweldw H-560™ See Wire

60
 Submerged Arc Welding Fluxes for Hardfacing

APPLICATIONS

Dia. Pkg Wt.

Common Use Weld Process Part Number In (mm) lbs (kg) Package Type Classification Weld Position

Modified Type 420 Flat, Horizontal,

SAW ED031860 N/A 60 (27.2) Plastic Bag
stainless deposit Circumferential

EN 760-S A F1; Flat, Horizontal,

ED019588 N/A 50 (22.7) Plastic Bag EN 760- S A FB 2 Circumferential
Roll Rebuilding, Idlers, Drive
SAW
Sprockets, Mill Buckets
550 EN 760-S A F1; Flat, Horizontal,
ED023403 N/A Steel Drum
(249.5) EN 760- S A FB 2 Circumferential

EN 760-S A CS 1; EN Flat, Horizontal,

ED032800 N/A 50 (22.7) Plastic Bag 760- S A CS 2 Circumferential
For Roll Rebuilding with wires SAW
containing certain alloys
450 EN 760-S A CS 1; Flat, Horizontal,
ED023365 N/A Steel Drum
(204.1) EN 760- S A CS 2 Circumferential

Drive/Drums, Mix, Crush 2700 Flat, Horizontal,

SAW ED027865 N/A Plastic Bag
Bar, Open Hearth, Mill, Blade (1224.7) Circumferential

Flat, Horizontal,
Concrete, Mix, Drive, Extrusion SAW ED036785 N/A 100 (45.4) Plastic Bag Circumferential

HARDFACING PRODUCTS AND GUIDE 61

FEATURED PRODUCTS
Engage in preventative maintenance — apply severe abrasion alloys
to the wear surfaces of your equipment
KEY Best Use Range of Use
MATCH A LINCOLN ELECTRIC HARDFACING PRODUCT TO YOUR WEAR TYPE

Severe Abrasion with Low

Weld Process Product Impact (Metal-To-Earth) Abrasion & Impact Metal-to-Metal High Impact

FCAW-S Lincoln SHS 9192U

FCAW-S Lincoln SHS 9800U

FCAW-S Lincoln SHS 9800E

FCAW-S Lincoln SHS 9700U

SMAW Lincoln SHS 9700E

FCAW-S Lincore 70-G

Hardbanding Lincoln Guardian CF

Hardbanding Lincoln Guardian HB

FCAW-S Lincoln SHS 9500U

FCAW-S Lincore 65-O

GMAW-C Lincore 60-G

FCAW-S Lincore 60-O

SMAW Wearshield 60

SMAW Wearshield ME

GMAW-C Lincore 57-G

FCAW-S Lincore 50

SMAW Wearshield 44

SMAW Wearshield ABR

GMAW-C Lincore M7-G

FCAW-S Lincore T&D

FCAW-S Lincore 55

FCAW-G Lincore 55-G

SMAW Wearshield MI

SMAW Lincore 42-S

FCAW-S Lincore 40-O

SMAW Lincore 40-S

FCAW-S Lincore 15CrMn

SMAW Wearshield 15CrMn

FCAW-S Lincore FROG MANG

SMAW Wearshield FROG MANG

FCAW-G Lincore M

SMAW Wearshield MANGJET

FCAW-S Lincore Super Rail

SMAW Wearshield® Super Rail

62
 Severe Abrasion/Low Impact

COMPARE FCAW SELF-SHIELDED

HARDFACING PRODUCTS
(Hardness and Abrasion Resistance)

KEY

LINCORE
Lincore 60-O
Lincore 55
Lincore 65-O
Lincore Ultra K

LINCOLN SHS
Lincoln SHS 9192U
Lincoln SHS 9700
Lincoln SHS 9800

75
HARDNESS (HRC)

COMPLEX CARBIDES

70

65
CHROME CARBIDES
MARTENSITIC

60

55

50

45

40
0.5 2.5 4.5 6.5 8.5 10.5
ABRASION RESISTANCE (1/ASTM G65 MASS LOSS)

HARDFACING PRODUCTS AND GUIDE 63

RESOURCES

64
Looking for Alloy Lot Certification?
Lincoln Electric has You Covered.

Q1 LOT® CERTIFICATION
ALL Lincoln Electric welding consumables undergo multiple quality checks as part of our
standard quality assurance system.
Analysis of the nose and tail sections of every green rod coil to assure that material meets the
mill spec as well as Lincoln Electric’s more stringent requirements. These and other checks
throughout the manufacturing process are meant to assure end-to-end consistency in:

• Product chemistry
• Mechanical properties
• Feedability and operation
• Traceability to the date of manufacture, line, shift and operator
Obtain a Q1 Certificate of Conformance and Certificate of Actual Chemistry at the web-based
Lincoln Electric Certificate Center, including SAW wire and flux combination certificates.

Q2 LOT® CERTIFICATION
ALL Lincoln Electric Stainless Steel, Nickel and Special Alloy welding consumables
have available LOT SPECIFIC records of:

• In-process testing and manufacturing

• Actual and deposit composition test results of the finished product
• Traceability to the date of manufacture, line, shift and operator
Obtain Q2 ACTUAL LOT CERTIFICATION OF TESTED LOT CONTROLLED MATERIALS
at the web-based Lincoln Electric Certificate Center.

Q3 LOT® CERTIFICATION
For Military and Nuclear certification and customers with special testing requirements or
requirements for archived records for a specific shipment.

• Product is made to order per customer’s requirements

• Certified Material Test Reports and all manufacturing records are archived
• Actual Certificate of Conformance and Certificate of Actual Chemistry is delivered to
the customer.

HARDFACING PRODUCTS AND GUIDE 65

Common
Package Types

BOTTLE PLASTIC SPOOL

Code: BO Code: SP
Weight: 10 Weight: 1, 2, 10, 16, 25

PLASTIC SPOOL
CARTON (VACUUM FOIL BAG)
Code: CT Code: SP
Weight: 10, 10/40 Weight: 25, 30, 33

EASY-OPEN CAN SPEED-FEED DRUM

Code: EO Code: D
Weight: 8/24 and 10/30, 10/40 Weight: 500, 600

COIL STEEL SPOOL

Code: C Code: SSP
Weight: 14/56, 50, 55, 60 Weight: 25,33

ACCU-TRAK® DRUM STEEL SPOOL

Code: AD (PRECISION LAYER WOUND)

Weight: 500 Code: SSP (PLW)

Weight: 33

PLASTIC BAG TUBE

Code: B Code: T
Weight: 50 Weight: 10/10 and 10/30

66
 Resources

Contact • Contact your local Lincoln Electric

sales representative

• Call our National Alloy Sales office at

1-800-638-1458

HARDFACING PRODUCTS AND GUIDE 67

 Safety Data Sheets (SDS) and Certificates of Conformance are available on our website at www.lincolnelectric.com

FUMES AND GASES can be hazardous to your health.

• Fumes from the normal use of this product contain significant quantities of potentially hazardous compounds. See consumable product label/insert.
• Keep your head out of the fumes.
• Use enough ventilation and local exhaust to keep fumes and gases from your breathing zone and the general area.
• An approved respirator should be used unless exposure assessments are below applicable exposure limits.

T E ST R E S U LTS
Test results for mechanical properties, deposit or electrode composition and diffusible hydrogen levels were obtained from a weld produced and tested according to prescribed standards, and should not be assumed to be the
expected results in a particular application or weldment. Actual results will vary depending on many factors, including, but not limited to, weld procedure, plate chemistry and temperature, weldment design and fabrication
methods. Users are cautioned to confirm by qualification testing, or other appropriate means, the suitability of any welding consumable and procedure before use in the intended application.

C U STOME R ASS I STA NC E P OL I CY

The business of Lincoln Electric is manufacturing and selling high quality welding equipment, automated welding systems, consumables, and cutting equipment. Our challenge is to meet the needs of our customers, who are experts
in their fields, and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for information or technical information about their use of our products. Our employees respond to inquiries to the best of their
ability based on information and specifications provided to them by the customers and the knowledge they may have concerning the application. Our employees, however, are not in a position to verify the information provided or to
evaluate the engineering requirements for the particular weldment, or to provide engineering advice in relation to a specific situation. Accordingly, Lincoln Electric does not warrant or guarantee or assume any liability with respect
to such information or communications. Moreover, the provision of such information or technical information does not create, expand, or alter any warranty on our products. Any express or implied warranty that might arise from the
information or technical information, including any implied warranty of merchantability or any warranty of fitness for any customers’ particular purpose or any other equivalent or similar warranty is specifically disclaimed.
Lincoln Electric is a responsive manufacturer, but the definition of specifications, and the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the
customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.

Publication C7.710 | Issue Date 05/21 THE LINCOLN ELECTRIC COMPANY

© Lincoln Global, Inc. All Rights Reserved.
22801 St. Clair Avenue • Cleveland, OH • 44117-1199 • U.S.A.
All trademarks and registered trademarks are the
property of their respective owners.
Phone: +1.216.481.8100 • www.lincolnelectric.com