HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

ELECTRONIC SYSTEM - Fault code index

Reference Description Controller
10001 Upper Lockout Solenoid Error
10002 Raise Solenoid Error
10003 Lower Solenoid Error
10004 Front Axle Position Sensor Threshold
Higher Than Set Limit
10005 Front Axle Position Sensor Threshold
Lower Than Set Limit
10008 Go Down Error - Suspension Unable
to Return to Set Point
10009 Lower Lockout Solenoid Error
10024 Front Suspension Not Calibrated
1002 Radar Disconnected
1003 Speed Sensor Error
1006 Slip Control Potentiometer Error
1009 Both External Switches Operated At
The Same Time
1010 Height Limit Potentiometer Error
1012 Drop Rate Control Potentiometer
Error
1014 Right Hand Load Sensing Pin Signal
Too Low
1015 Right Hand Load Sensing Pin Signal
Too High
1021 Draft Sensitivity Control
Potentiometer Error
1025 Position Control Potentiometer Error
1027 Lift Arm Position Sensing Control
Voltage Too Low
1033 Draft Control Potentiometer Error
1049 Wheel speed sensor open circuit
1068 Height Limit Control Not Set To
Maximum During Calibration
1070 Hydraulic Ram Configuration Not Set
1070 Hydraulic Ram Configuration Not Set
14015 5V Supply Voltage - Too High
14016 5V Supply Voltage - Too Low
14051 Fuel Level Sensor Open Circuit Or
Short To High Voltage
14052 Fuel Level Sensor Short To Ground
14061 Air Brake Pressure Sensor - Short
Circuit to VCC or Option Set But
Sensor Not Connected
14091 Transmission Output Speed Sensor -
Short To Vcc Or Open Circuit
14092 Transmission Output Speed Sensor -
Short To Ground
14097 Transmission Oil Pressure Sensor -
Short To 5V
14098 Transmission Oil Pressure Sensor
- Open Circuit Or Short Circuit To
Ground
14100 Airbrake system not configured
14900 Transmission Controller Missing
14901 Engine Controller Missing (EDC16)
14902 Auxiliary Controller Missing

T6000-T4-SM_EN 15/02/2012
A.50.A / 3
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

14905 Keypad Missing (JA)
14906 Steering Controller Missing (KA)
14907 Gear Display Missing
15002 Steering Wheel Control Proximity
Sensor Open Circuit.
15003 Steering Wheel Control Proximity
Sensor - Short Circuit
15006 Split Valve LVDT - Open Circuit
15007 Split Valve LVDT - Short Circuit
15008 Change Valve Solenoid - Open Circuit
15009 Change Valve Solenoid - Short Circuit
Across
15010 Safety Switch Fail
15011 Maximum Engagement Time Elapsed
(5 Minutes)
15012 Split Valve Spool - Stuck Open
15013 Change Valve Or Split Valve Spools -
Stuck Closed
15014 Split Valve Spool Stuck in Transition
Zone - Unable to Identify Steering
Mode
15024 System Not Calibrated
16111 Cab Temperature Sensor Open or
Shorted to Power Plus
16112 Cab Temperature Sensor Shorted to
Ground
16113 Outlet Temperature Sensor Open or
Shorted to Power Plus
16114 Outlet Temperature Sensor Shorted
to Ground
16115 Evaporator Temperature Sensor
Open or Shorted to Power Plus
16116 Evaporator Temperature Sensor
Shorted to Ground
16117 Outside Air Temperature Sensor
Open or Shorted to Power Plus
16118 Outside Air Temperature Sensor
Shorted to Ground
16120 Blower Speed Select Potentiometer
Open Or Shorted To Power
16121 Temperature Select Potentiometer
Open or Shorted to Power Plus
16122 Mode Select Potentiometer Open Or
Shorted To Power
16125 High Pressure Switch (+) Input
Shorted To Power
16126 High pressure switch (+) input shorted
to ground
16127 High pressure switch (-) input shorted
to power
16128 High Pressure Switch (-) Input
Shorted To Ground
16129 High Pressure Cycling Error (2 in 1
Minute)
16130 Low pressure switch (+) input shorted
to power
16131 Low Pressure Switch (+) Input
Shorted To Ground

T6000-T4-SM_EN 15/02/2012
A.50.A / 4
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

16132 Low Pressure Switch (-) Input Shorted
To Power
16133 Low Pressure Switch (-) Input Shorted
To Ground
16134 Low Pressure Switch Open For
Greater Than 1 Minute
19003 Battery voltage sensing (electrical)
- signal high - P0563 batter voltage
evaluation - above upper limit
19004 Battery voltage sensing (electrical)
- signal low - P0562 battery voltage
evaluation - below lower limit
19010 Temperature sensor after catalyst
(electrical) - signal high - P042D
catalyst temperature sensor circuit
high
19011 Temperature sensor after catalyst
(electrical) - signal low - P042C
catalyst temperature sensor circuit
low
19019 Temperature sensor before catalyst
(electrical) - signal high - P0428
catalyst temperature sensor circuit
high
19020 Temperature sensor before catalyst
(electrical) - signal low - P0427
catalyst temperature sensor circuit
low
19037 Sensor supply 2 (5V internal; for urea
pressure sensors) - supply voltage
too high - P204D reagent - pressure
sensor - short circuit high
19038 Sensor supply 2 (5V internal; for urea
pressure sensors) - supply voltage
too low - P204C Reagent - pressure
sensor - short circuit low
19046 Urea pressure sensor in box
(electrical) - supply voltage error -
P204A Reagent - pressure sensor -
open circuit
19047 Urea pressure sensor in box
(electrical) - signal high - P204D
reagent - pressure sensor - short
circuit high
19048 Urea pressure sensor in box
(electrical) - signal low - P204C
reagent - pressure sensor - short
circuit low
19055 Urea temperature sensor in box
(electrical) - high signal - P2045
reagent - temperature sensor of
pump module - short circuit high
19056 Urea temperature sensor in box
(electrical) - signal low - P2044
reagent - temperature sensor of
pump module - short circuit low

T6000-T4-SM_EN 15/02/2012
A.50.A / 5
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

19073 Voltage supply 2 - tube heaters (UB2)
electrical - short to bat at UB2 with
key 15 off - P20C4 reagent - suction
tube heating - short circuit high
19074 Voltage supply 2 - tube heaters (UB2)
electrical - open circuit to UB2 -
P20C1 reagent - suction tube heating
- open circuit
19075 Voltage supply 2 - tube heaters (UB2)
electrical - short circuit to ground
UB2 - P20C3 reagent - suction tube
heating - short circuit low
19082 Voltage supply 3 - coolant control
valve and reverting valve (UB3)
electrical - short to bat at UB3
with key 15 off - P20A3 vent valve
(reductant purge control valve) - short
circuit high
19083 Voltage supply 3 - coolant control
valve and reverting valve (UB3)
electrical - open circuit to UB3 -
P20A0 vent valve (reductant purge
control valve) - open circuit
19084 Voltage supply 3 - coolant control
valve and reverting valve (UB3)
electrical - short circuit to ground UB3
- P20A2 vent valve (reductant purge
control valve) - short circuit low
19091 Monitoring VDD11/VDD25 voltage -
dosing valve/pump motor - supply
voltage VD11 low - P0659 12 volt
supply for dosing module - below
lower limit
19092 Monitoring VDD11/VDD25 voltage -
dosing valve/pump motor - supply
voltage VD11 high - P0658 12 volt
supply for dosing module - above
lower limit
19145 Dosing valve (electrical) - short circuit
to battery + - P2049 reductant injector
- circuit high
19147 Dosing valve (electrical) - open load
- P2047 reductant injector - circuit
open
19149 Dosing valve (electrical) - short circuit
to ground - P2048 reductant injector
circuit low
19154 Urea pump speed - pump motor
unplugged - P208B reagent-pump
not delivering
19155 Urea pump speed - pump motor
blocked - P208A reagent-pump
19156 Urea pump speed - pump overspeed
- P208D reagent-pump over speed
19157 Urea pump speed - hall sensors
defect - P208B reagent-pump not
delivering

T6000-T4-SM_EN 15/02/2012
A.50.A / 6
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

19181 Reverting valve (4-2 way valve)
electrically - short circuit to battery -
P20A3 vent valve (reductant purge
control valve) - short circuit high
19183 Reverting valve (4-2 way valve)
electrically - open load - P20A0 vent
valve (reductant purge control valve)
- open circuit
19262 Tank heating valve - short circuit
to battery - P20B4 reagent - tank
heating valve - short circuit high
19264 Tank heating valve - open load -
P20B1 reagent - tank heating valve
- open circuit
19265 Tank heating valve - short circuit
to ground - P20B3 reagent - tank
heating valve - short circuit low
19290 Temperature after catalyst too low -
down stream catalyst temp - physical
(Catalyst heating time failed) - P042B
catalyst temperature sensor circuit
range/performance
19298 Urea pressure too low at system start
- urea pressure too low at system
start - P208B reagent - pump not
delivering
19307 Urea pressure too high - urea
pressure not plausible (urea pressure
too high) - P204B reagent - pressure
above threshold
19316 Urea temperature in pump module
out of range - urea temperature box
- physical (urea box temp not ok:
outside range) - P2043 reagent -
temperature sensor of pump module
out of range
19325 Urea temperature in tank out of
range - urea temperature tank -
physical (urea tank temp not ok:
outside range) - P205B reagent - tank
temperature sensor (temperature of
the reagent - solution in the tank) out
of range
19334 System frozen and not free in time
- defreezing mode and detection
errors (inlet line defreezing failed) -
P20C2 reagent - suction tube heating
- detection mode of heating
19335 System frozen and not free in time -
defreezing mode and detection errors
(pressure line defreezing failed)
- P20BE reagent - pressure tube
heating - detection mode of heating
19336 System frozen and not free in time
- defreezing mode and detection
errors (pressure build-up in detection
mode failed) - P20C5 pump module -
internal heating - open circuit

T6000-T4-SM_EN 15/02/2012
A.50.A / 7
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

19337 System frozen and not free in time -
defreezing mode and detection errors
(back-flow line defreezing failed)
- P20B9 reagent - backflow tube
heating - open circuit
19352 Reverting valve (4-2 way valve)
mechanically - valve does not open
- P20A0 vent valve (reductant purge
control valve) - open circuit
19361 Battery voltage (actual value) - high
battery voltage - P0562 battery
voltage evaluation - below lower limit
19362 Battery voltage (actual value) - low
battery voltage - P0563 battery
voltage evaluation - above upper limit
19370 Urea pressure too low (in
commissioning status) - pump
motor error during commissioning
(pump not delivering) - P208B
reagent - pump not delivering
19379 Urea temperature too low during
commissioning - temperatures not
plausible during commissioning
19415 Empty urea tank - urea tank empty
- P203F reagent - fluid level in tank
- too low
19532 Back flow line clogged - P2063
reagent - dosing valve - short circuit
low
19541 Coolant control valve mechanically -
blocked closed - P20A1 vent valve
test plausibility test (startup)
19550 Pressure line blocked - pressure line
blocked - P209B reagent - dosing
nozzle - pressure too high
19559 Low urea level 1 (warning) - urea
level below Limit 1 - P203F reagent -
fluid level in tank - too low
19568 Low urea level 2 (warning) - urea
level below Limit 2 - P203F reagent -
fluid level in tank - too low
19577 CAN receive frame E2SCR (dosing,
exh gas flow, exh gas temp, error
suppression, heater, long term failure)
- SAE J1939 check for CAN receive
signal : (urea quantity not in range) -
P0600 serial communication link
19578 CAN receive frame E2SCR (dosing,
exh gas flow, exh gas temp, error
suppression, heater, long term failure)
- SAE J1939 check for CAN receive
signal : (dosing status not in range) -
P0600 serial communication link
19579 CAN receive frame E2SCR (dosing,
exh gas flow, exh gas temp, error
suppression, heater, long term
failure) - timeout - P0600 serial
communication link

T6000-T4-SM_EN 15/02/2012
A.50.A / 8
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

19580 CAN receive frame E2SCR (dosing,
exh gas flow, exh gas temp, error
suppression, heater, long term failure)
- too many CAN messages - P0600
serial communication link
19581 CAN receive frame E2SCR (dosing,
exh gas flow, exh gas temp, error
suppression, heater, long term failure)
- SAE J1939 check for CAN receive
signal - P0600 serial communication
link
19595 CAN receive frame EEC1 (Driver
demand, eng speed, eng torque) -
SAE J1939 check for CAN receive
signal : (engine torque not in range) -
P0600 serial communication link
19597 CAN receive frame EEC1 (driver
demand, eng speed, eng torque) -
timeout - P0600 serial communication
link
19598 CAN receive frame EEC1 (driver
demand, eng speed, eng torque) -
too many CAN messages - P0600
serial communication link
19599 CAN receive frame EEC1 (driver
demand, eng speed, eng torque) -
SAE J1939 check for CAN receive
signal : (torque driver demand not in
range) - P0600 serial communication
link
19604 CAN receive frame ET1 (oil and
water temp engine) - SAE J1939
check for CAN receive signal : (oil
temperature not in range) - P0600
serial communication link
19605 CAN receive frame ET1 (oil and water
temp engine) - timeout - P0600 serial
communication link
19606 CAN receive frame ET1 (oil and
water temp engine) - too many
CAN messages - P0600 serial
communication link
19607 CAN receive frame ET1 (oil and
water temp engine) - SAE J1939
check for CAN receive signal : (water
temperature not in range) - P0600
serial communication link
19649 Urea tank level error (CAN message
or electrical with real sensor) - level
over CAN: SAE J1939 no signal
available level sensor connected
directly: sensor supply error - P203A
reagent - tank level sensor - open
circuit
19650 Urea tank level error (CAN message
or electrical with real sensor) - level
over CAN: SAE J1939 signal not
in range level sensor connected
directly: SRC high - P203D reagent -
tank level sensor - short circuit high

T6000-T4-SM_EN 15/02/2012
A.50.A / 9
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

19651 Urea tank level error (CAN message
or electrical with real sensor) - level
over CAN: SAE J1939 erroneous
signal level sensor connected directly:
SRC low - P203C reagent - tank level
sensor - short circuit low
19721 EEPROM / checksum failures -
EEPROM write error - P062F internal
control module EEPROM error
19722 EEPROM / checksum failures - no
corresponding variant number error
- P062F internal control module
EEPROM error
19723 EEPROM / checksum failures -
EEPROM communication error
- P062F internal control module
EEPROM error
19724 EEPROM / checksum failures
- EEPROM detection error or
codierwort error - P062F internal
control module EEPROM error
19725 EEPROM / checksum failures - wrong
EEPROM size - P062F internal
control module EEPROM error
2001 Shuttle Too Fast Error ('N' Displayed)
2001 Shuttle Too Fast Error ('N' Displayed)
2011 Clutch Pedal Potentiometer - Voltage
Too Low
2011 Clutch Pedal Potentiometer - Voltage
Too Low
2012 Clutch Pedal Potentiometer - Voltage
Too High
2012 Clutch Pedal Potentiometer - Voltage
Too High
2015 High and Low Range Switches Both
Closed
2016 Creeper Solenoid Short To Ground
Or High Voltage
2024 All Clutches Not Calibrated
2024 All Clutches Not Calibrated
2027 Engine speed no signal
2035 Dump Solenoid Short To Ground Or
High Voltage
2037 Clutch Pedal Disconnect Switch -
Open Circuit
2037 Clutch Pedal Disconnect Switch -
Open Circuit
2038 Clutch 4 Solenoid Short To Ground
Or High Voltage
2038 High Range PWM Valve Short To
Ground Or High Voltage
2039 Clutch 4 Solenoid Open Circuit
2039 High Range PWM Valve Open Circuit
2040 Clutch 3 Solenoid Short To Ground
Or High Voltage
2040 Low Range PWM Valve Short To
Ground Or High Voltage
2041 Clutch 3 Solenoid Open Circuit

T6000-T4-SM_EN 15/02/2012
A.50.A / 10
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

2041 Low Range PWM Valve Open Circuit
2042 Clutch 2 Solenoid Short To Ground
Or High Voltage
2043 Clutch 2 Solenoid Open Circuit
2044 Clutch 1 Solenoid Short To Ground
Or High Voltage
2045 Clutch 1 Solenoid Open Circuit
2047 Clutch Pedal Disconnect Switch Set
Too High
2047 Clutch Pedal Disconnect Switch Set
Too High
2048 Clutch Pedal Disconnect Switch Set
Too Low
2048 Clutch Pedal Disconnect Switch Set
Too Low
2051 Oil Temperature Sensor Open Circuit
2051 Oil Temperature Sensor Open Circuit
2055 Wheel Speed (Transmission Output
Speed) Sensor - No Signal
2055 Wheel Speed (Transmission Output
Speed) Sensor - No Signal
2056 Low Range Switch Open
2057 High Range Switch Open
2058 Seat Switch Closed
2058 Seat Switch Closed
2061 Forward/Reverse Synchroniser
Potentiometer Signal Too High
2061 Forward/Reverse Synchroniser
Potentiometer Signal Too High
2062 Forward/Reverse Synchroniser
Potentiometer Signal Too Low
2062 Forward/Reverse Synchroniser
Potentiometer Signal Too Low
2063 Forward Synchroniser Did Not
Engage
2063 Forward Synchroniser Did Not
Engage
2064 Reverse Synchroniser Did Not
Engage
2064 Reverse Synchroniser Did Not
Engage
2065 Forward Synchroniser Solenoid Open
Circuit
2065 Forward Synchroniser Solenoid Open
Circuit
2066 Reverse Synchroniser Solenoid
Open Circuit
2066 Reverse Synchroniser Solenoid
Open Circuit
2067 Forward Synchroniser Solenoid Short
To Ground Or High Voltage
2067 Forward Synchroniser Solenoid Short
To Ground Or High Voltage
2068 Reverse Synchroniser Solenoid Short
To Ground Or High Voltage
2068 Reverse Synchroniser Solenoid Short
To Ground Or High Voltage

T6000-T4-SM_EN 15/02/2012
A.50.A / 11
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

2070 Shuttle Lever Forward Switch Voltage
Too High
2070 Shuttle Lever Forward Switch Voltage
Too High
2071 Shuttle Lever Forward Switch Voltage
Too Low
2071 Shuttle Lever Forward Switch Voltage
Too Low
2072 Shuttle Lever Reverse Switch Voltage
Too High
2072 Shuttle Lever Reverse Switch Voltage
Too High
2073 Shuttle Lever Reverse Switch Voltage
Too Low
2073 Shuttle Lever Reverse Switch Voltage
Too Low
2075 Flywheel Speed Sensor Signal Error
2075 Flywheel Speed Sensor Signal Error
2076 Flywheel Speed Sensor Open Circuit
2076 Flywheel Speed Sensor Open Circuit
2077 Flywheel Speed Sensor - Short
Circuit
2077 Flywheel Speed Sensor - Short
Circuit
2079 Flywheel Speed Sensor - No Signal
2079 Flywheel Speed Sensor - No Signal
2081 4/5 Range Synchroniser
Potentiometer Signal High
2082 4/5 Range Synchroniser
Potentiometer Signal Low
2083 1-4 Range Synchroniser Engaged
Error
2084 5-8 Range Synchroniser Engaged
Error
2085 1-4 Range Synchroniser Solenoid
Open Circuit
2086 5-8 Range Synchroniser Solenoid
Open Circuit
2087 1-4 Range Synchroniser Solenoid
Short To Ground Or High Voltage
2088 5-8 Range Synchroniser Solenoid
Short To Ground Or High Voltage
2091 Clutch 3 Not Calibrated
2092 Clutch 4 Not Calibrated
2093 High Clutch Not Calibrated
2094 Low Clutch Not Calibrated
2095 Clutch 1 Not Calibrated
2096 Clutch 2 Not Calibrated
2097 Clutch 5 Not Calibrated
2098 Clutch 5 Solenoid Short Circuit
2099 Clutch 5 Solenoid Open Circuit
2100 Clutch 5 Dump Solenoid Short Circuit
2101 Clutch 5 Dump Solenoid Open Circuit
3001 Foot Throttle Sensor - Signal Not
Plausible
3002 Foot Throttle Sensor - Signal Above
Range Maximum

T6000-T4-SM_EN 15/02/2012
A.50.A / 12
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3003 Foot Throttle Sensor - Signal Below
Range Minimum
3010 Air Intake Temperature Sensor -
Signal Above Range Maximum
3011 Air Intake Temperature Sensor -
Signal Below Range Minimum
3047 Main Relay Failure - Short Circuit To
Battery
3048 Main Relay Failure - Short Circuit to
Ground
3088 Crankshaft Sensor - No Signal
3090 Camshaft Sensor - No Signal
3091 Camshaft Sensor - Invalid Signal
3096 ECM Bussoff On CAN A
3107 Fuel Metering Unit - Short Circuit To
Battery
3108 Fuel Metering Unit - Short Circuit To
Ground
3113 Main relay 1 (high pressure pump
- power supply to the fuel metering
unit) - short to battery
3114 Main relay 1 (high pressure pump
- power supply to the fuel metering
unit) - short to ground
3118 ECM 12V sensor - supply voltage
high
3120 PTO Twist Sensor - Not Plausible
3121 PTO Twist Sensor - Open Circuit
3122 PTO Twist Sensor - Short Circuit To
Ground
3123 PTO Twist Sensor - Not Calibrated
3124 Hand Throttle - Signal Above Range
Maximum
3125 Hand Throttle - Channel 2 Signal
Below Range Minimum
3138 Metering Unit - Temperature Too High
3141 Fuel Flow Setpoint Too Low
3142 High Pressure Test - Test Active
3145 Terminal 15 - No Signal
3148 Coolant Temperature Sensor
Dynamic Test - Failure
3157 ECM Not Detected On CAN Bus
3158 Invalid ECM Checksum
3159 Invalid Engine Reference Torque
3160 Fan Actuator - Short Circuit to Battery
3162 Fan Actuator - Open Load
3163 Fan Actuator - No Load
3166 Fuel Filter Heater Relay - Short
Circuit To Battery
3168 Fuel Filter Heater Relay - Open Load
3169 Fuel Filter Heater Relay - Signal Not
Plausible
3176 Setpoint Of Metering Unit Not
Plausible In Overrun
3177 Engine Overspeed Detected
3182 Timeout Of CAN Message RxCCVS
3182 Timeout Of CAN Message RxCCVS

T6000-T4-SM_EN 15/02/2012
A.50.A / 13
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3183 Timeout of CAN message TSC1-VR
(when active)
3184 Timeout of CAN message TSC1-VR
(when inactive)
3238 Engine Controller Internal SPI
Communication Error
3239 Engine Controller EEPROM - Read
Operation Error
3240 Engine Controller EEPROM - Write
Operation Failure
3241 Engine Controller EEPROM - Default
Value Used
3250 Dataset - Variant Defect
3251 Dataset - Requested Variant Could
Not Be Set
3252 Controller Watchdog - SPI
Comunication Failure
3258 High side power - short circuit to
battery
3259 High side power - short circuit to
ground
3261 Low side power - short circuit to
battery or excess temperature
3265 Overrun Monitoring
3266 Redundant Engine Speed in Overrun
Monitoring
3267 Main relay 3 - short circuit to battery
3268 Main relay 3 - short circuit to ground
3301 Rail Pressure Negative Deviation Too
High On Minimum Metering
3305 Rail Pressure Below Minimum Limit
In Controller Mode
3309 Rail Pressure Above Maximum Limit
In Controlled Mode
3313 Rail Pressure Drop Rate Too High
3316 Minimum Number Of Injections Not
Reached - Stop Engine
3319 DM1DCU SPN2 message - error in
DCU active
3320 DM1DCU SPN3 message - error in
DCU active
3321 DM1DCU SPN4 message - error in
DCU active
3322 DM1DCU SPN5 message - error in
DCU active
3334 Timeout Of CAN Message TCS1-PE
Torque - When Active
3335 Timeout Of CAN Message TSC1-PE
Torque - When Inactive
3338 Timeout Of CAN Message TSC1-VE
Speed - When Inactive
3339 Timeout Of CAN Message TSC1-VE
Speed - When Active
3339 Timeout Of CAN Message TSC1-VE
Speed - When Active
3354 Engine Brake Exhaust Valve - Short
Circuit To Ground

T6000-T4-SM_EN 15/02/2012
A.50.A / 14
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3355 Engine Brake Exhaust Valve - Short
Circuit To Battery
3358 CAN transmit timeout
3367 Coolant Temperature Test Failure
3368 Torque Limitation Due To OBD
Performance Limiter By Legislation
3369 Torque Reduction Due To Smoke
Reduction
3370 Torque Limitation Due To Engine
Protection (Against Excessive
Torque, Engine Overspeed And
Overheat)
3512 DCU state monitoring - DCU not
ready in time
3513 SCR Catalyst not present - relation of
temperature behavior between both
catalyst temperatures not plausible
3517 Ambient air temperature sensor
failure (of humidity sensor) - signal
too high
3518 Ambient air temperature sensor
failure (of humidity sensor) - signal
too low
3521 NOx estimation failure - estimated
NOx signal not reliable
3528 NOx sensor plausibility failure - signal
not plausible
3529 NOx sensor failure - open load
3530 NOx sensor failure - short circuit
3532 NOx sensor failure - sensor not ready
in time
3533 CAN message timeout NOx (from
NOx sensor) - CAN timeout
3533 CAN message timeout NOx (from
NOx sensor) - CAN timeout
3541 CAN message timeout SCR1 (from
DCU) - CAN timeout
3545 SCR dosing valve overheat protection
- torque limitation level 2 for SCR
protection active
3546 SCR dosing valve overheat protection
- torque limitation level 1 for SCR
protection active
3549 Humidity sensor signal ratio failure -
signal ratio above limit
3550 Humidity sensor signal ratio failure -
signal ratio below limit
3555 CAN message timeout SCR2 (from
DCU) - CAN timeout
3557 Humidity sensor possibly saturated
with water droplets - signal ratio
above limit
3558 Humidity sensor possibly saturated
with water droplets - signal ratio
below limit
3561 NOx value not plausible (after
treatment plausibility)
3565 Urea quality and urea warning level 1

T6000-T4-SM_EN 15/02/2012
A.50.A / 15
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3569 Urea quality and urea warning level 2
3577 DM1DCU SPN1 message - error in
DCU active
3581 Performance limitation active due to
either stage
3585 Engine shut off urea level (after idling
phase)
3586 Plausibility check of catalyst system
- temperature after catalyst not
plausible
3587 Plausibility check of catalyst system
- temperature before catalyst not
plausible
3588 Plausibility check of catalyst system
- ambient temperature of humidity
sensor or both catalyst temperatures
not plausible
3589 Plausibility check of catalyst system
- temperature deviation between up
and downstream catalyst temperature
too high during operation
3591 SCR catalyst thermal aging limit
exceeded - P0422 main catalyst
efficiency below threshhold
3593 Poor reagent quality
3594 Torque limitation due to SCR
3599 Error path of oxidation catalyst not
present - P0421 warm up catalyst
efficiency below threshold
3602 Defect ratio between threshold limits
- P0425 catalyst temperature sensor
circuit
3605 Temperature of outer control loop -
temperature deviation above limit
3606 Temperature of outer control loop -
temperature deviation below limit
3609 Urea quality and urea warning level 4
3611 Catalyst efficiency lower than first
NOx prediction threshold level
3612 Catalyst efficiency lower than second
NOx prediction threshold level
3999 Unknown ECM SPN Error Code
4100 Rear Remote No.1 No Control
Message Received
4101 Rear Remote No.1 Control Message
Not Plausible
4102 Rear Remote No.1 EEPROM Error
4102 Rear Remote No.1 EEPROM Error
4103 Rear Remote No.1 Switched To
Failsafe
4104 Rear Remote No.1 Under Voltage
4105 Rear Remote No.1 Over Voltage
4106 Rear Remote No.1 Spool Movement
Too Low
4107 Rear Remote No.1 Spool Movement
Too High
4108 Rear Remote No.1 Float Position Not
Reached

T6000-T4-SM_EN 15/02/2012
A.50.A / 16
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

4109 Rear Remote No.1 Manually
Operated
4110 Rear Remote No.1 Driver Faulty
4111 Rear Remote No.1 Potentiometer
Faulty
4111 Rear Remote No.1 Potentiometer
Faulty
4112 Rear Remote No.1 Unable To Reach
Neutral
4113 Rear Remote No.1 Spool Not In
Neutral At Key On
4114 Rear Remote No.2 No Control
Message Received
4115 Rear Remote No.2 Control Message
Not Plausible
4116 Rear Remote No.2 EEPROM Error
4117 Rear Remote No.2 Switched To
Failsafe
4118 Rear Remote No.2 Under Voltage
4119 Rear Remote No.2 Over Voltage
4120 Rear Remote No.2 Spool Movement
Too Low
4121 Rear Remote No.2 Spool Movement
Too High
4122 Rear Remote No.2 Float Position Not
Reached
4123 Rear Remote No.2 Manually
Operated
4124 Rear Remote No.2 Driver Faulty
4125 Rear Remote No.2 Potentiometer
Faulty
4125 Rear Remote No.2 Potentiometer
Faulty
4126 Rear Remote No.2 Unable To Reach
Neutral
4127 Rear Remote No.2 Spool Not In
Neutral At Key On.
4128 Rear Remote No.3 No Control
Message Received
4129 Rear Remote No.3 Control Message
Not Plausible
4130 Rear Remote No.3 EEPROM Error
4131 Rear Remote No.3 Switched To
Failsafe
4132 Rear Remote No.3 Under Voltage
4133 Rear Remote No.3 Over Voltage
4134 Rear Remote No.3 Spool Movement
Too Low
4135 Rear Remote No.3 Spool Movement
Too High
4136 Rear Remote No.3 Float Position Not
Reached
4137 Rear Remote No.3 Manually
Operated
4138 Rear Remote No.3 Driver Faulty
4139 Rear Remote No.3 Potentiometer
Faulty

T6000-T4-SM_EN 15/02/2012
A.50.A / 17
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

4140 Rear Remote No.3 Unable To Reach
Neutral
4141 Rear Remote No.3 Spool Not In
Neutral At Key On
4142 Rear Remote No.4 No Control
Message Received
4143 Rear Remote No.4 Control Message
Not Plausible
4144 Rear Remote No.4 EEPROM Error
4145 Rear Remote No.4 Switched To
Failsafe
4146 Rear Remote No.4 Under Voltage
4147 Rear Remote No.4 Over Voltage
4148 Rear Remote No.4 Spool Movement
Too Low
4149 Rear Remote No.4 Spool Movement
Too High
4150 Rear Remote No.4 Float Position Not
Reached
4151 Rear Remote No.4 Manually
Operated
4152 Rear Remote No.4 Driver Faulty
4153 Rear Remote No.4 Potentiometer
Faulty
4154 Rear Remote No.4 Unable To Reach
Neutral
4155 Rear Remote No.4 Spool Not In
Neutral At Key On
4170 Rear EHR Control No.1 Not
Calibrated
4173 Rear EHR Control No.2 Not
Calibrated
4177 Rear EHR Control No.3 Not
Calibrated
4180 Rear EHR Control No.4 Not
Calibrated
4190 Rear Remote No.1 No
Communications
4191 Rear Remote No.2 No
Communications
4192 Rear Remote No.3 No
Communications
4193 Rear Remote No.4 No
Communications
5005 Rear PTO Brake Switch Open Circuit
5007 Rear PTO Solenoid - Open Circuit Or
Short Circuit To Ground
5008 Rear PTO Solenoid - Open Circuit
5027 Rear PTO Speed Sensor - Open
Circuit
5034 Rear PTO Fender Switch Open
Circuit / Short To Ground
5037 Rear PTO Cab Normally Open Switch
- Stuck Closed
5043 Rear PTO Fender Switch Stuck On
5044 Rear PTO Speed Sensor - Short To
Ground

T6000-T4-SM_EN 15/02/2012
A.50.A / 18
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

5098 Rear PTO Fender Switch Option Not
Enabled
5099 Auto PTO Mode Not Enabled
6023 Four Wheel Drive Solenoid Open
Circuit
7017 Differential Lock Solenoid - Open
Circuit
7024 Steering Angle Sensor Not Calibrated
7032 Steering Angle Sensor - Signal Too
Low
8007 Front PTO Solenoid - Stuck On
8008 Front PTO Solenoid - Open Circuit
8033 Front PTO Switch In Cab Normally
Closed Open Circuit
8037 Front PTO Cab Normally Open
Switch Stuck Closed
8099 Front PTO Option Not Enabled
9001 Front Hitch Position Sensor - Short
Circuit To 12V
9002 Front Hitch Position Sensor - Open
Circuit Or Short To Ground
9003 Front Hitch Fender Up Switch Error
9004 Front Hitch Fender Down Switch
Error
9005 Front Hitch Fender Common Switch
Error
9006 Front Hitch Position Potentiometer -
Not Calibrated
14200 Error With Electrical Programmable ADIC
Read Only Memory (EEPROM)
3167 Fuel Filter Heater Relay - Short ECM
Circuit To Ground
3006 Coolant Temperature Sensor - Signal EDC
Not Plausible
3007 Coolant Temperature Sensor - Signal EDC
Above Range
3008 Coolant Temperature Sensor - Signal EDC
Below Range Minimum
3015 Fuel Temperature Sensor - Signal EDC
Above Maximum
3016 Fuel Temperature Sensor - Signal EDC
Below Range Minimum
3019 Boost Pressure Sensor - Signal EDC
Above Range Maximum
3022 Boost Pressure Sensor - Signal Not EDC
Plausible
3023 Atmospheric Pressure Sensor - EDC
Signal Not Plausible
3024 Atmospheric Pressure Sensor - EDC
Signal Above Range Maximum
3025 Atmospheric Pressure Sensor - EDC
Signal Below Range Minimum
3028 Oil Pressure too low EDC
3029 Oil Pressure Sensor - Short Circuit EDC
To Battery
3030 Oil Pressure Sensor - Short Circuit EDC
To Ground
3031 Oil Pressure Sensor - Hardware Error EDC

T6000-T4-SM_EN 15/02/2012
A.50.A / 19
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3032 Oil Pressure Sensor - Value Too High EDC
3033 Oil Temperature Sensor - Signal Not EDC
Plausible (Compared With Coolant
Temperature)
3034 Oil Temperature Sensor - Signal EDC
Above Range Maximum
3035 Oil Temperature Sensor - Signal EDC
Below Range Minimum
3037 Boost Pressure Sensor - Signal Low EDC
3051 Battery Voltage To Engine Controller EDC
- Voltage Too High
3052 Battery Voltage To Engine Controller EDC
- Voltage Too Low
3059 ECM afterrun was interrupted EDC
3060 Cylinder 1 - Unclassifiable Error In EDC
Injector
3061 Cylinder 1 - Injector Cable Short EDC
Circuit (Low Side To Battery)
3063 Cylinder 1 - Injector Cable Short EDC
Circuit (High Side To Ground)
3064 Cylinder 5 - Unclassifiable Error in EDC
Injector
3065 Cylinder 5 - Injector Cable Short EDC
Circuit (Low Side To Battery)
3067 Cylinder 5 - Injector Cable Short EDC
Circuit (High Side To Ground)
3068 Cylinder 3 - Unclassifiable Error In EDC
Injector
3069 Cylinder 3 - Injector Cable Short EDC
Circuit (Low Side To Battery)
3071 Cylinder 3 - Injector Cable Short EDC
Circuit (High Side To Ground)
3072 Cylinder 6 - Unclassifiable Error In EDC
Injector
3073 Cylinder 6 - Injector Cable Short EDC
Circuit (Low Side To Battery)
3075 Cylinder 6 - Injector Cable Short EDC
Circuit (High Side To Ground)
3076 Cylinder 2 - Unclassifiable Error In EDC
Injector
3077 Cylinder 2 - Injector Cable Short EDC
Circuit (Low Side To Battery)
3079 Cylinder 2 - Injector Cable Short EDC
Circuit (High Side To Ground)
3080 Cylinder 4 - Unclassifiable Error In EDC
Injector
3081 Cylinder 4 - Injector Cable Short EDC
Circuit (Low Side To Battery)
3083 Cylinder 4 - Injector Cable Short EDC
Circuit (High Side To Ground)
3089 Crankshaft Sensor - Invalid Signal EDC
3093 Offset Between Camshaft And EDC
Crankshaft - Outside Boundaries
3095 Operating With Camshaft Sensor EDC
Only - Backup Mode
3102 Rail Pressure Sensor CP3 - Signal EDC
Below Range Minimum

T6000-T4-SM_EN 15/02/2012
A.50.A / 20
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3104 Rail Pressure Relief Valve - Open EDC
3105 Rail Pressure Relief Valve - Pressure EDC
Shock Requested
3106 Rail Pressure Relief Valve - Did Not EDC
Open After Pressure Shock
3110 Rail Pressure Sensor Monitoring - EDC
Signal Above Range Maximum
3111 Rail Pressure Sensor Monitoring - EDC
Signal Below Range Minimum
3112 Rail Pressure Sensor CP3 - Signal EDC
Above Maximum Range
3119 ECM 12V sensor supply voltage low EDC
3131 Grid Heater Always Switched On EDC
3137 Metering Unit - Open Load EDC
3146 Water detected in fuel EDC
3147 Oil Temperature Too High EDC
3154 Grid Heater Relay - Short Circuit To EDC
Battery
3155 Grid Heater Relay - Short Circuit To EDC
Ground
3156 Grid Heater Relay - No Load EDC
3161 Fan Actuator - Short Circuit to Ground EDC
3179 Time-out Of CAN Message BC2EDC2 EDC
3180 Time-out of CAN Message VM2EDC EDC
3188 Cylinder 1 Warning - Open Load EDC
3192 Cylinder 2 warning - Open Load EDC
3196 Cylinder 3 Warning - Open Load EDC
3200 Cylinder 4 Warning - Open Load EDC
3204 Cylinder 5 Warning - Open Load EDC
3208 Cylinder 6 Warning - Open Load EDC
3210 Bank 1 - General Short Circuit To EDC
Injector Cable
3211 Bank 1 - Injector cable Short Circuit EDC
Low Side To Ground
3213 Bank 1 - Unclassifiable Error EDC
3218 Bank 2 - General Short Circuit On EDC
Injector Cable
3219 Bank 2 - Injector Cable Short Circuit EDC
Low Side To Ground
3221 Bank 2 - Unclassifiable Error EDC
3227 Injection Processor Error - Internal EDC
Reset/Clock Loss/Voltage Too Low
3228 Injection Processor Error - EDC
Unlocked/Initialization Error
3229 Injection Processor Error - Injections EDC
Limited By Software
3230 Injection Processor Error - SPI EDC
Communication Failure
3231 Injection Processor Error - Internal EDC
Reset/Clock Loss/Voltage Too Low
3232 Injection Processor Error - EDC
Unlocked/Initialization Failure
3233 Injection Processor Error - Test Mode EDC
3234 Injection Processor Error - SPI EDC
Communication Failure
3242 Engine Controller (Locked) Recovery EDC
Occurred

T6000-T4-SM_EN 15/02/2012
A.50.A / 21
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

3243 Engine Controller Recovery EDC
(Suppressed) - Recovery Occurred
3244 Engine Controller Recovery (Visible) EDC
- Recovery Occurred
3245 Engine Controller - Watchdog Not EDC
Plausible
3246 Shutoff Paths During Initialization - EDC
Watchdog
3247 Shutoff Paths Failed During EDC
Initialization - Supply Voltage Too
High
3248 Shutoff Paths During Initialization - EDC
Supply Voltage Too Low
3253 ADC Monitoring - Reference Voltage EDC
Too Low
3254 ADC Monitoring - Reference Voltage EDC
Too High
3255 ADC Monitoring Test Impulse Error EDC
3256 ADC Monitoring Queue Error EDC
3278 Engine Controller Supply Voltage Too EDC
High
3280 Sensor Supply Voltage 1 - High EDC
3281 Sensor Supply Voltage 1 - Low EDC
3283 Sensor Supply Voltage 2 - High EDC
3284 Sensor Supply Voltage 2 - Low EDC
3285 Sensor Supply Voltage 3 - High EDC
3286 Sensor Supply Voltage 3 - Low EDC
3371 Torque Limitation Due To Fuel EDC
Quantity Limitation Because Of
Injector System Errors
2026 Engine Speed Too High TCU
2036 Dump Solenoid Open Circuit TCU
1004 Wheel Speed Sensor Signal Too High XCM (multi-function CM)
1008 Raise / Work Switch Failure XCM (multi-function CM)
(Command Arm)
1016 Left Hand Load Sensing Pin Signal XCM (multi-function CM)
Too Low
1017 Left Hand Load Sensing Pin Signal XCM (multi-function CM)
Too High
1018 Both Load Sensing Pins XCM (multi-function CM)
Disconnected
1019 Load Sensing Pin 8V Reference XCM (multi-function CM)
Voltage Too Low
1020 Load Sensing Pin 8V Reference XCM (multi-function CM)
Voltage Too High
1024 Perform The Hydraulic Lift Calibration XCM (multi-function CM)
1028 Lift Arm Position Sensing Control XCM (multi-function CM)
Voltage Too High
1029 Hydraulic Control Valve Disconnected XCM (multi-function CM)
1031 Chassis Harness Disconnected XCM (multi-function CM)
1063 EDC Hydraulic Valve Lower Solenoid XCM (multi-function CM)
Open Circuit
1064 EDC Hydraulic Valve Raise Solenoid XCM (multi-function CM)
Open Circuit
1065 EDC Hydraulic Valve Lower Solenoid XCM (multi-function CM)
Short Circuit

T6000-T4-SM_EN 15/02/2012
A.50.A / 22
 HYDRAULIC, PNEUMATIC, ELECTRICAL, ELECTRONIC SYSTEMS - FAULT CODES

Reference Description Controller

1066 EDC Hydraulic Valve Raise Solenoid XCM (multi-function CM)
Short Circuit
2052 Oil Temperature Sensor - Short XCM (multi-function CM)
Circuit
2052 Oil Temperature Sensor - Short XCM (multi-function CM)
Circuit
2053 5 Volt Reference Voltage Too High XCM (multi-function CM)
2053 5 Volt Reference Voltage Too High XCM (multi-function CM)
2054 5 Volt Reference Voltage Too Low XCM (multi-function CM)
2054 5 Volt Reference Voltage Too Low XCM (multi-function CM)
2059 Shuttle Lever Switch Disagreement XCM (multi-function CM)
2059 Shuttle Lever Switch Disagreement XCM (multi-function CM)
5033 Rear PTO Cab Normally Closed XCM (multi-function CM)
Switch Open Circuit
5035 Rear PTO Fender Switch Input Short XCM (multi-function CM)
To 12V+

T6000-T4-SM_EN 15/02/2012
A.50.A / 23