HOME STORE BLOG SCHEMATICS TUTORIALS DOWNLOADS
CONTACT
1KM Power FM Transmitter
1KM Power FM Transmitter
This small power FM transmitter can transmit more than 1 km in good conditions. The modulation can be made so much
with a microphone or audio source. Circuit of power fm transmitter is built around 2n2218 transistor. Transmitter coil is 5
turns of enameled 22 AWG wire, with diameter of 1 cm without nucleus. Look at the capacitors that it should be ceramic.
The antenna should possess from 15 to 40 cm. For transmission it ties a receiver of FM (radio) in the proximity to half
volume in a free frequency (that there is not any radio operating), with a wood or plastic key, rotate the screw of CV to
capture the frequency of the transmitter.
If it has difficulties of fittings, remove the coil and wind her again with more or less it turns. Look at pinage of the
transistor 2n2218. Mic1 is a microphone of electrets of two terminals, THE resistor R1 makes the polarization of the
microphone, perhaps it is necessary to alter the value of R1 to adapt to your microphone, values of 1k up to 10k can be
tested. Preferably use plate of glass fiber, that is the appropriate for high frequency. Perhaps for better frequency stability
to be necessary to place the antenna on second turn of the coil, weld the thread piece used as antenna second it turn of
the coil L1.
Below we have the schematic of the one of the circuit of the transmitter of FM.
List of Material for assembly of the fm transmitter
Resistors 5% 1/4 w:
R1 = 3 a 10kΩ (black, black, orange, gold)
R2 = 6,8kΩ (Blue, Gray, red, gold).
R3=4,7kΩ (yellow, violet, red, gold. )
R4 = 39Ω (Orange, White, black, gold.
Ceramic Capacitors
C1=4,7 nF (472 or 4n7 or 4700)
C2=2,2 nF (2200 or 2n2 or 222)
C3 = 4.7pF (4p7 or 4.7)
C4 = 100 nF (100n, or 0.1 or 104)
C5 = TRIMMER CV 3-30 PF.
Transistor:
T1 = 2n2218 or equivalent.
Several:
L1 = see the text
B1 = Battery of 9 volts alkaline.
Mic1 = electret microphone.
Several = printed circuit board, antenna, box, etc.
Board fm transmitter side of the copper Scale 3:1
2218 pcb Circuit of power fm transmitter transistor 2n2218 audio wireless 1KM
Board fm transmitter side of the components
2218 comp Circuit of power fm transmitter transistor 2n2218 audio wireless 1KM
Pinage of the transistor 2N2218 sees underneath
500m Circuit of power fm transmitter transistor 2n2218 audio wireless 1KM
Users electronic tags:
2n2218, FM transmitter circuit approximte 1km, transmissor fm 2n2218.
Related Links
Accurate LC Meter
ESR Meter / Transistor Tester / LC Meter
BA1404 HI-FI Stereo FM Transmitter
500mW FM / VHF Transmitter Amplifier / Booster
USB IO Board
60MHz Frequency Meter / Counter
1Hz - 2MHz Function Generator
Voltmeter Ammeter
USB Voltmeter
Accurate 0-500MHz RF Power Meter
Audiophile OPA2132 Headphone Amplifier Kit
DS18S20 Dual Temperature Meter
BH1417 Stereo PLL FM Transmitter
50mW BH1417 Stereo PLL FM Transmitter
Phone FM Transmitter
TV Transmitter with Audio
5 Watt FM Amplifier
TDA7000 FM Receiver / TV Tuner / Aircraft Receiver
NJM2035 HI-FI Stereo Encoder / Multiplexer
Downloads
1KM Power FM Transmitter - Link
Accurate LC Meter PIC Volt Ampere Meter
Build your own Accurate LC Meter (Capacitance Inductance Volt Ampere Meter measures voltage of 0-70V or 0-500V with
Meter) and start making your own coils and inductors. This LC 100mV resolution and current consumption 0-10A or more
Meter allows to measure incredibly small inductances making with 10mA resolution. The meter is a perfect addition to any
it perfect tool for making all types of RF coils and inductors. LC power supply, battery chargers and other electronic projects
Meter can measure inductances starting from 10nH - 1000nH, where voltage and current must be monitored. The meter
1uH - 1000uH, 1mH - 100mH and capacitances from 0.1pF up uses PIC16F876A microcontroller with 16x2 backlighted LCD.
to 900nF. The circuit includes an auto ranging as well as reset
switch and produces very accurate and stable readings.
60MHz Frequency Meter / Counter 1Hz - 2MHz XR2206 Function Generator
Frequency Meter / Counter measures frequency from 10Hz to 1Hz - 2MHz XR2206 Function Generator produces high quality
60MHz with 10Hz resolution. It is a very useful bench test sine, square and triangle waveforms of high-stability and
equipment for testing and finding out the frequency of various accuracy. The output waveforms can be both amplitude and
devices with unknown frequency such as oscillators, radio frequency modulated. Output of 1Hz - 2MHz XR2206 Function
receivers, transmitters, function generators, crystals, etc. Generator can be connected directly to 60MHz Counter for
setting precise frequency output.
BA1404 HI-FI Stereo FM Transmitter USB IO Board
Be "On Air" with your own radio station! BA1404 HI-FI Stereo USB IO Board is a tiny spectacular little development board /
FM Transmitter broadcasts high quality stereo signal in 88MHz parallel port replacement featuring PIC18F2455/PIC18F2550
- 108MHz FM band. It can be connected to any type of stereo microcontroller. USB IO Board is compatible with Windows /
audio source such as iPod, Computer, Laptop, CD Player, Mac OSX / Linux computers. When attached to Windows IO
Walkman, Television, Satellite Receiver, Tape Deck or other board will show up as RS232 COM port. You can control 16
stereo system to transmit stereo sound with excellent clarity individual microcontroller I/O pins by sending simple serial
throughout your home, office, yard or camp ground. commands. USB IO Board is self-powered by USB port and can
provide up to 500mA for electronic projects. USB IO Board is
breadboard compatible.
ESR Meter / Capacitance / Inductance / Audiophile Headphone Amplifier Kit
Transistor Tester Kit
Audiophile headphone amplifier kit includes high quality audio
ESR Meter kit is an amazing multimeter that measures ESR grade components such as Burr Brown OPA2134 opamp, ALPS
values, capacitance (100pF - 20,000uF), inductance, volume control potentiometer, Ti TLE2426 rail splitter, Ultra-
resistance (0.1 Ohm - 20 MOhm), tests many different types Low ESR 220uF/25V Panasonic FM filtering capacitors, High
of transistors such as NPN, PNP, FETs, MOSFETs, Thyristors, quality WIMA input and decoupling capacitors and Vishay Dale
SCRs, Triacs and many types of diodes. It also analyzes resistors. 8-DIP machined IC socket allows to swap OPA2134
transistor's characteristics such as voltage and gain. It is an with many other dual opamp chips such as OPA2132,
irreplaceable tool for troubleshooting and repairing electronic OPA2227, OPA2228, dual OPA132, OPA627, etc. Headphone
equipment by determining performance and health of amplifier is small enough to fit in Altoids tin box, and thanks to
electrolytic capacitors. Unlike other ESR Meters that only low power consumption may be supplied from a single 9V
measure ESR value this one measures capacitor's ESR value battery.
as well as its capacitance all at the same time.
Arduino Prototype Kit 200m 4-Channel 433MHz Wireless RF Remote
Control
Arduino Prototype is a spectacular development board fully
compatible with Arduino Pro. It's breadboard compatible so it Having the ability to control various appliances inside or
can be plugged into a breadboard for quick prototyping, and it outside of your house wirelessly is a huge convenience, and
has VCC & GND power pins available on both sides of PCB. It's can make your life much easier and fun. RF remote control
small, power efficient, yet customizable through onboard 2 x provides long range of up to 200m / 650ft and can find many
7 perfboard that can be used for connecting various sensors uses for controlling different devices, and it works even
and connectors. Arduino Prototype uses all standard through- through the walls. You can control lights, fans, AC system,
hole components for easy construction, two of which are computer, printer, amplifier, robots, garage door, security
hidden underneath IC socket. Board features 28-PIN DIP IC systems, motor-driven curtains, motorized window blinds,
socket, user replaceable ATmega328 microcontroller flashed door locks, sprinklers, motorized projection screens and
with Arduino bootloader, 16MHz crystal resonator and a reset anything else you can think of.
switch. It has 14 digital input/output pins (0-13) of which 6
can be used as PWM outputs and 6 analog inputs (A0-A5).
Arduino sketches are uploaded through any USB-Serial
adapter connected to 6-PIN ICSP female header. Board is
supplied by 2-5V voltage and may be powered by a battery
such as Lithium Ion cell, two AA cells, external power supply
or USB power adapter.
Electronics-DIY.com © 2002-2022. All Rights Reserved.
