Tel:+86-20-62326088 Fax:+86-20-62326077
1.4 Main Function Interface
1.5 LED Displaying Board Function
1.6 Menu
2.7 TIMER SET 12
13
15
16
17
17
18
18
19
19
20
20
21
21
22
22
23
24
24
25
1
1.1 Transmitter Chart
(TIMER START)
(TIMER RESET)
2 3
12. 2.4GHz Binding 15. LED displaying board function
4.0
13. Basic features
F100
4.0V.
14. Main function Interface
4.8V MOD6
F100
FUN. TIMER
Voltage 4.8V MOD6
F100 Model Memory SYS. 00:00
Function FUN. TIMER Timer
System SYS. 00:00
4 5
1.6 MENU 2.1 System menu introduction
4.8V MOD6
F100
FUN. TIMER
SYS. 00:00
TIMER SET
MODEL SET(Page8～9)
PLANE TYPE(Page10)
STICK MODE(Page10)
STICK ADJ(Page11)
TRAINER (Page11)
6 7
2.2 MODEL SET
8 9
2.3 PLANE TYPE 2.5 STICK ADJ
TIMER SET
2.6 TRAINER
2.4 STICK MODE
TRAINER
TIMER SET
1)Press“down”to select “SYS MENU”,and press“ENTER”to come to the interface.
2)Press“up”or“down”to select “NORMAL”or“TRAINER”.
10 11
2.7 TIMER SET 3.1 Function. menu introduction(Heli.)
4.8V MOD6
FUN. TIMER
SYS. 00:00
Choose Timer set
Operation
1. Press Down to select Sys Menu, and press Enter to the interface
2. Down button select Timer SET
3. Up and Down button setting time M:S
4. Entering setting Timer Press INC or DEC choosing increase and decrease
5. Return main Interface. INC -- TIMER START DEC -- TIMER RESET
DR(Page 14)
Caution:This setting before and after 20seconds each two seconds Alarm.
after Alarming each 10 seconds. then Alarm not stop.
Press DEC --- TIMER RESET LOGOUT TIME RENEW TIMER
SUB TRIM(Page 16)
TRAVEL(Page 17)
TRAVEL(Page 17)
12 13
SWASH MIX(Page 18) 3.2 D/R
SUB.TRIM
GYRO.SENS(Page 18)
A/E/R D/R
THRO.CURV(Page 19)
MONITOR(Page 19)
A/E/R D/R
PIT.CURV(Page 20)
THRO.HOLD(Page 20)
14 15
3.4 TRAVEL
A/E/R D/R
3.5 CH.REV
3.3 SUB TRIM
16 17
3.6 SWASH.MIX 3.8 THRO CURV
Throttle curve operation
Operation:
1)Press“up”to select “FUN MENU”,and press“ENTER”to come to the interface.
2)Press“up”or“down”to select “THRO CURV”,and now the shadow area is the item that
can be set currently.Press“ENTER”to go to the next step.
3)Press“ENTER” to select the throttle curve point.There are 5 points,they are L,1,2,3,H.
Press“INC”or“DEC”to set the corresponding value separately,and the throttle curve will
change accordingly.
4)There are three throttle curves to be selected,normal,“IDLE 0”and“IDLE 1”by the switch at
the left top of the transmitter..
5)After your setting,press“EXIT”to save the setting and leave the operation.
Remark:the transmitter can save 3 groups of different throttle curves.When you make 3D fly,
3.7 GYRO.SENS please ask for instruction from experienced pilots.
3.9 MONITOR
Monitor system
Operation:
1)Press“up”to select “FUN MENU”,and press“ENTER”to come to the interface.
2)Press“up”or“down”to select “MONITOR”,and now the shadow area is the item that can
be set currently.Press“ENTER”to go to the next step.
3)When you move the sticks or channel switches,you can find the corresponding channel bars will
change accordingly.This function is designed to monitor the working conditions of the
transmitter.
4)After your setting,press “EXIT”to save the setting and leave the operation.
Remark:this function helps you adjust the setting,neutral trim as well as channel inspection.
18 19
3.10 PIT.CURV 4.1 Function menu for fixed wing plane
4.2 V-Tail function menu
3.11 THRO.HOLD
20 21
4.3 Delta mix function menu
5.1 Heli.Connection Diagram(3Servos CCPM)
22 23
5.3 V-Tail Connection Diagram
Technology Data
DELTA-MIX Connection Diagram
24 25
