User Manual

H6Pro Master Smart Diagnostic System

Version 6.7

Revise date 2022/10

Shenzhen Xtooltech Intelligent Co., LTD

Please read this user manual carefully before using the H6PRO MASTER Smart Diagnostic System, referred to as the “Scan
Tool” throughout this document. When reading the manual, please pay attention to the words “Note” or “Caution”, and read
them carefully for appropriate operation.

OPERATION INSTRUCTIONS
For safe operation, please follow the instructions below:

⚫ Keep the device away from heat or fumes when in use.

⚫ If the vehicle battery contains acid, please keep your hands and skin or fire sources away from the battery during
testing.
⚫ The exhaust gas of the vehicle contains harmful chemicals. Please ensure adequate ventilation.
⚫ Do not touch the vehicle cooling system components or exhaust manifolds when the engine is running due to the high
temperatures reached.
⚫ Make sure the car is securely parked, Neutral is selected or the selector is at the P or N position to prevent the vehicle
from moving when the engine starts.
⚫ Make sure the (DLC) Diagnostic Link Connector is functioning properly before starting the test to avoid damage to the
Diagnostic Computer.
⚫ Do not switch off the power or unplug the connectors during testing. Doing so may damage the ECU (Electronic
Control Unit) and/or the Diagnostic Computer.

CAUTIONS!
⚫ Avoid shaking, dropping or dismantling the scan tool as it may damage the internal components.
⚫ Use only your fingertips to touch the LCD screen. Hard or sharp objects may damage the scan tool.
⚫ Do not use excessive force;
⚫ Do not expose the screen to strong sunlight for a long period.
⚫ Please keep the scan tool away from water and moisture.
⚫ Store and use the scan tool only within the temperature ranges identified in the Technical Specifications section.
⚫ Keep the unit away from strong magnetic fields.

AFTERSALES-SERVICES
XTOOL strives to provide best-in-class support!

E-Mail: supporting@xooltech.com

Tel: +86 755 21670995 or +86 755 86267858 (China)

Official Website: www.xtooltech.com | www2.xtooltech.com (Alternate sites)

I
CONTENT
OPERATION INSTRUCTIONS ............................................................................................................................ I

CAUTIONS! .......................................................................................................................................................... I

AFTERSALES-SERVICES .................................................................................................................................. I

CONTENT ............................................................................................................................................................ I

1. GENERAL INTRODUCTION ..................................................................................................................... 4

Tablet ............................................................................................................................................................................... 4

VCI Box............................................................................................................................................................................ 5

Connection Methods ........................................................................................................................................................ 5

Bluetooth connection........................................................................................................................................................................... 5

Wire connection ..................................................................................................................................................................................... 6

J2534 Pass-thru...................................................................................................................................................................................... 7

2. GETTING STARTED ................................................................................................................................. 8

Connecting Power............................................................................................................................................................ 8

Activation ......................................................................................................................................................................... 9

2. DIAGNOSTIC .......................................................................................................................................... 10

Beginning Diagnostic Testing ........................................................................................................................................ 11

Vehicle Selection.................................................................................................................................................................................. 11

Diagnosis functions............................................................................................................................................................................. 12

ECU Coding & Programming .......................................................................................................................................................... 19

3. SPECIAL FUNCTIONS ........................................................................................................................... 20

5.1 ABS BLEEDING....................................................................................................................................................... 20

5.2 OIL RESET .............................................................................................................................................................. 23

5.3 EPB.......................................................................................................................................................................... 24

5.3 SAS.......................................................................................................................................................................... 25

5.5 BMS RESET ............................................................................................................................................................ 27

i
 5.6 INJECTOR CODING................................................................................................................................................ 28

5.7 DPF REGENERATION ............................................................................................................................................ 30

5.8 TPMS RESET .......................................................................................................................................................... 33

6. REPORT .................................................................................................................................................. 35

Report ............................................................................................................................................................................ 36

Replay............................................................................................................................................................................ 37

File Manager .................................................................................................................................................................. 38

7. SETTINGS ............................................................................................................................................... 38

Language ....................................................................................................................................................................... 38

Units............................................................................................................................................................................... 39

Bluetooth........................................................................................................................................................................ 39

Self-test.......................................................................................................................................................................... 40

My Workshop Info .......................................................................................................................................................... 41

Firmware Information ..................................................................................................................................................... 42

About ............................................................................................................................................................................. 42

8. UPDATE & FACTORY RESET ............................................................................................................... 43

Update ........................................................................................................................................................................... 43

Delete Software ............................................................................................................................................................. 44

Factory Reset ................................................................................................................................................................ 44

9. FAQ.......................................................................................................................................................... 46

Q1: Failed to generate Diagnostic report ....................................................................................................................... 46

Q2: How to print a Diagnostic report .............................................................................................................................. 46

Q3: Failed to extract files ............................................................................................................................................... 46

Q4: Mailbox supported ................................................................................................................................................... 46

Q5: How to make an appointment for remote support ................................................................................................... 46

Q6: How to generate and upload diagnostic log files ..................................................................................................... 46

Q7: How to switch language .......................................................................................................................................... 47

Q8: Failed to diagnose vehicle ....................................................................................................................................... 47

Q9: Failed to activate or register .................................................................................................................................... 47

ii
 Q10: Failed to turn on when charging ............................................................................................................................ 47

Q11: Failed to open the Diagnostic app ......................................................................................................................... 47

Q12: Can’t receive the email after sharing the diagnostic report ................................................................................... 47

10. WARRANTY & SERVICES ..................................................................................................................... 47

11. REMOTE ASSISTANCE ......................................................................................................................... 48

12. APPENDIX ............................................................................................................................................... 50

Trademarks .................................................................................................................................................................... 50

Copyright ....................................................................................................................................................................... 50

Button Description.......................................................................................................................................................... 50

Function Buttons .................................................................................................................................................................................. 50

Navigation Buttons ............................................................................................................................................................................. 51

Notification Bar .................................................................................................................................................................................... 51

iii
1. GENERAL INTRODUCTION
The XTOOL H6Pro Master smart diagnostic system (referred to as the “Scan Tool”) is an advanced scanning tool based on
the Android operating system. It supports multiple languages and is suitable for different countries and regions. The
advantage of this OBD-II (On-Board Diagnostics version 2) scanner is its comprehensive functions and its ability to quickly
provide the user with more accurate diagnostic information.

H6Pro Master Smart diagnostics System main units included:

• Tablet
• Wireless Diagnostic Module: VCI (Vehicle communication interface) box
• OBD2 Adapter
• Programming cables
• Special connectors

TABLET

1. 10.1-inch touch screen

2. USB 3.0 Port

3. RJ45 Port –connect to network cable
to access the Ethernet
4. DB15 Port - Reserved, not available
for vehicle communication
5. DC Power Input Port
6. Power Button – Long press to turn
off/on the tablet, short press to enter
sleeping mode
7. Rear Camera
8. Speaker
9. Wireless charging port - for use with
wireless charging dock (sold
separately)

4
VCI BOX

1. DB15 Port
2. Display with vehicle voltage
3. DB9 Port
4. Reset button - Long press to reset the
VCI box

CONNECTION METHODS

BLUETOOTH CONNECTION

The scan tool must be connected to the vehicle’s OBD-II port so that the tablet can establish correct vehicle communication.
Please perform the following steps:

1 Turn on the tablet

2 Connect VCI with Vehicle via main test cable and OBD adapter, make sure Bluetooth connection works fine
3 Switch on the ignition and tap on the Diagnostic application to start your diagnosis.

Note: The vehicle’s DLC is not always located under the dash; for the location of the DLC, please refer to
the vehicle owner’s manual. Some older vehicles are not compatible with the OBDⅡ-16 adapter, please make
sure you’re using the correct adapter.

The Bluetooth connection method is shown in the figure below:

5
 1. Tablet 3. Test cable (DB15 to DB15)
2. OBD2-16 Adapter 4. VCI box

WIRE CONNECTION

When using functions such as ECU programming & coding, please use the special programming cable for different
manufacturers to connect the tablet to the VCI box to prevent the failure of function execution due to unstable data
transmission and thus any other damage.

For BMW

1. Tablet
2. VCI box
3. BMW Programming cable (DB15 to OBD2 with USB 3.0)

6
For Others

1. Tablet 4. DB15 to DB15 Cable

2. General Programming Cable (USB 3.0 to Type-B) 5. OBD2-16 Adapter
3. VCI box

 For models with DoIP protocol communication, please be sure the device is connected to vehicle by wire.

J2534 PASS-THRU

XTOOL provides only a J2534 pass-thru device, which is running on a PC. And the firmware version for drivers needs to be
strictly consistent with the diagnostic software. The new firmware may not be compatible with the old diagnostic software,
and vice versa. Please update them carefully since the operation is irreversible.

7
 1. OBD2 adapter 3. DB9 to USB 3.0 cable
2. DB15 to DB15 main cable 4. PC

! Note: Before use, please make sure that the OEM diagnostic software has been installed on your PC

The operation guidelines of J2534 pass-thru driver are shown as below:

• Step 1: Download and install the J2534 pass-thru software, XVCI MAX (Download link: www.xtooltech.com)
• Step 2: Connect the car, VCI box and PC as shown above
• Step 3: Install the OEM driver by the path: Open XTOOL VCI driver>>Vehicle Diagnosis>>My
Application>>choose the OEM driver you need>>install the driver
• Step 4: Start the diagnostic software by the path: Open XTOOL VCI driver >>Vehicle Diagnosis >> My
Application >> choose the software you need >>operation

⚫ Precautions for Diagnosis

1. The voltage range on the car: +9~+36V DC;

2. When testing some special functions, the operator must operate according to the prompts and meet the test conditions.
For some models [special functions], the conditions that need to be met are: engine water temperature 80 ℃~105 ℃, turn
off headlights and air conditioners, keep the accelerator pedal in the released position, etc.;

3. The electronic control systems of different models are very complicated. If you encounter situations where it is impossible
to test or a large amount of test data is abnormal, you can search for the ECU of the vehicle and select the menu for the
model on the ECU nameplate;

4. If the vehicle type or electronic control system to be tested is not found in the diagnostic function, please upgrade the
vehicle diagnostic software to the latest version using the Updates menu or consult the XTOOL technical service department;

5. Only wiring harnesses provided by XTOOL and designed for the scan tool are permitted to be used with this scan tool to
avoid damage to the vehicle or the scan tool;

6. When running a Diagnostics function, it is forbidden to shut down the scan tool directly. You should cancel the task before
returning to the main interface and then shutting down the scan tool.

2. GETTING STARTED

CONNECTING POWER

The scan tool may need to be charged before first use. Confirm the proper power adapter (either 120 VAC North American
or 240 VAC European version) is attached to the AC/DC charger.

Plug the AC/DC charger into a wall outlet

Plug the USB cable into the AC/DC charger and also into the scan tool’s micro-USB charging port.

Note: a fully discharged battery will take approximately 6 hours to fully charge. The scan tool can be used while charging.

8
ACTIVATION

After first-time users press and hold the power button to turn on the system, the system will automatically enter the guided
process and request the user to select the language for the operating system.

After setting the system language, click Next to enter the Wi-Fi connection page, as shown below:

Select a network to connect to on the Wi-Fi connection page. You need to enter the Wi-Fi password to establish Wi-Fi
connectivity and the activation page, as shown in the figure below. You can also click the "Trial" button in the upper right
corner to try it out before activation. However, activation is highly recommended to take advance of any new online software
updates.

9
Click Start Activation to enter the activation page, as shown below:

A pop-up window showing Activation Success indicates that you have completed the first boot setup, and please input
your email address as requested

Click OK to enter the diagnostic system and start using the device.

2. DIAGNOSTIC
The diagnostic application can read ECU information, read and clear DTC (Diagnostic Trouble Codes) and check live data
and freeze frame data. The Diagnostic application can access the ECU of various vehicle control systems, including the
Engine, Transmission, Anti-lock Braking System (ABS), Airbag Safety Restraing System (SRS), Electronic Parking Brake
system (EPB) and perform many types of actuation tests.

10
BEGINNING DIAGNOSTIC TESTING

After the tablet device is properly connected to the vehicle, you could start the vehicle diagnosis.

VEHICLE SELECTION

The scan tool supports the following 3 ways to access the smart diagnostics system.

⚫ AUTO SCAN
⚫ MANUAL INPUT
⚫ SELECT VEHICLE BY AREA

Click the VIN button in the upper left corner and then choose to enter the vehicle diagnosis through either AUTO SCAN or
MANUAL INPUT.

AUTO SCAN: It supports the automatic reading of vehicle VIN code. You also can tap on the button “AUTO SCAN” on the
diagnosis system entrance to use this function. Please make sure that the car and the device are well connected before
using this function.

If your model is not recognized, please try the following steps:

① UPDATE all software, and check whether the APP is updated in [Settings]
② Please click Diagnosis on the main menu to enter the selection menu, manually select the engine system to
read the ECU information, and confirm whether the VIN can be read.
③ Contact the XTOOL technical team to provide the VIN code to confirm whether the model supports automatic
identification of VIN.

MANUAL ENTER: It supports manual input of car VIN code. When entering the VIN code manually, make sure that the 17
characters entered are correct to ensure accurate test results.

11
⚫ SELECT VEHICLE BY AREA

In addition to the above 3 methods, you can also choose a car brand by selecting the appropriate region at the top of the
screen. You can select the vehicle model that needs to be diagnosed according to the area, as shown below:

OBD-II supports reading the related fault codes of the Powertrain Control Module (PCM);

DEMO, a demonstration program; Click this button to experience and learn the operation processes of the diagnostic
function

Some models provide multiple entry methods in the sub-menu, including:

⚫ Automatic Detection
⚫ Manual Selection
⚫ System Selection

Automatic Detection will automatically identify the vehicle's VIN code, and then read the information of your target
diagnostic object. If you choose "Manual selection", then you can continue to select the vehicle brand, year, and model of
the vehicle in the sub-menu to diagnose the vehicle. Enter "System Selection", you can also diagnose the vehicle according
to the system according to your needs after selecting the model.

DIAGNOSIS FUNCTIONS

Diagnostics functions supported by the scan tool are listed below:

12
⚫ Read ECU Information
⚫ Read/Clear Trouble Code
⚫ Read Live Data
⚫ Freeze Frame
⚫ Actuation Test (Bi-Directional Control)
⚫ Special functions

⚫ READ ECU INFORMATION

This function is to read ECU version information and is the equivalent of "System Identification" or "System Information”
in some electronic control systems. These equivalent terms all refer to reading ECU-related software and hardware versions,
models and production date of diesel engines, part numbers, etc. This information is helpful when recording maintenance
records and ordering new parts

⚫ READ TROUBLE CODE

13
In the process of diagnosis, if the device shows “System is OK” or “No Trouble Code”, it means there is no related trouble
code stored in ECU or some troubles are not under the control of ECU. Most troubles are mechanical system troubles or
executive circuit troubles. It is also possible that the signal of a sensor may be inaccurate but within limits, which can be
examined using Live Data.

⚫ CLEAR TROUBLE CODE

It allows for clearing current and historical trouble codes stored in the ECU memory, under the premise that all the troubles
have been resolved.

Some troubles are immediately detected by the ECU with the key in the run position and without the engine running. Other
troubles are not detected until very specific test conditions are met such as engine coolant temperature within a range,
speed within a range for a duration of time, throttle percentage within a range, etc.

If the trouble codes are erased when the trouble remains unresolved, the trouble code will reappear in the ECU the next
time the ECU performs the specific diagnostic test for that trouble.

If the trouble is resolved but there is a stored trouble code, sometimes the ECU will detect the resolution and clear the
trouble code or more likely, classify it as “historical” trouble.

If the trouble is resolved and the user clears the trouble codes, the trouble history will be cleared.

If the user intends to have another colleague or mechanic investigate the problem, it is not recommended for the user to
clear the trouble code since doing so may erase information helpful to others who may investigate the issue.

DTC Status Descriptions Suggestions

Current DTC’s can be cleared using the

Current DTC’s are trouble codes that are stored in the
Clear DTC’s function of the Scantool, or
ECU when both continuous and non-continuous (2 trip)
Current /Present when the ECU monitor (2 trip monitor) has
monitors fail. Current DTC’s command the MIL On the
ran and completed 40 consecutive trips
instant they are stored in the ECU.
without a fault.
History DTC’s are trouble codes stored in the ECU
History DTC’s set in conjunction with
when continuous and non-continuous monitors (2nd
Current DTC’s and are not cleared by the
trip) fail. History DTC’s set in conjunction with Current
History/Stored ECU monitor. History DTC’s can only be
DTC’s and are not cleared by the ECU monitor. History
cleared using the Clear DTC function of
DTC’s can only be cleared using the Clear DTC function
the Scantool.
of the Scantool.
Pending codes are codes that prep themselves when
they determine a fault that engine cycle. They are
Typically pending codes are not to severe
basically a preliminary investigation for your engine. To
but you shouldn’t ignore them either, it can
Pending simplify, a random malfunction can occur during the
be cleared using the Clear DTC’s function
current drive cycle but only happen for a split second.
of the Scantool
This will cause the malfunction to throw a “pending
code”.

14
 Permanent DTC’s cannot be cleared using
Permanent DTC’s are trouble codes that are stored in
the Clear DTC’s function on the Scantool.
the ECU when continuous and non-continuous
Permanent Instead, Permanent DTC’s are cleared
monitors fail. Permanent DTC’s are set in conjunction
when the ECU monitor completes and
with Current and History DTC’s.
passes three consecutive trips.

For Volkswagen
The fault cannot be cleared directly by
Active/Static means that the fault is happening at the using the Clear DTC’s function of the
Active/static
moment and can/should be take care of. diagnostic tool and the internal fault of the
car must be eliminated manually
It is a fault that has occurred in the past and can be
Passive/sporadic cleared by Scantool, and user should to check if the /
DTC will appear again.

⚫ READ LIVE DATA

Real-time information about various sensors is called “Live Data”. Live Data includes parameter identifications (PIDs) of
the running engine such as oil pressure, temperature, engine speed, fuel oil temperature, coolant temperature, intake air
temperature, etc. Based on these parameters, we can predict directly where the problem lies, which helps to narrow the
scope of maintenance. For some vehicles, during their actual operation, the problems such as performance characteristics
or sensitivity reduction, can be evaluated using live data.

!Note: The speed may vary depending on the speed of data sent from the vehicle and the number of data parameters being
shown.

Click the magnifying glass on the top right, you can search for related PIDs based on keywords

15
⚫ Custom

⚫ The scan tool includes support to select and show multiple PIDs. Click Display All to display all PIDs. This enables
you to see relationships between data parameters.

⚫ Combine
The scan tool includes support to select multiple PIDs and click Combine to combine different graphs into one chart.

⚫ Data recording
The scan tool supports recording the current data values in the form of text. You can view the recorded files in
Reports->Data Replay.

16
⚫ Pause

Click this button to pause the recording timeline. It freezes the data display, for closer examination and review.

⚫ FREEZE FRAME
When the signal of the sensor is abnormal, the ECU will save the data at that moment of failure to form a freeze-frame. It is
usually used to analyze the reasons that may lead to component(?) failures.

The live data items supported by vehicles of different brands are not the same, so the freeze frames displayed when
diagnosing vehicles of different brands may also be different. Some vehicles may not have the option of a freeze-frame
which means that the model does not support this function.

Take Renault Duster ii ph as an example. After selecting the system to enter the lower freeze frame menu, the device will
list all the fault codes under the system.

Users can click on a fault code, such as DF1068 to view the freeze frame recorded by the car when the fault code occurs,
including context when the fault appeared, and current context and additional data.

17
Context when fault appeared: record the live data when fault appeared to help the user to know the vehicle status. *Some
vehicles don't support this function; users will get a prompt when they click the menu.

Current context: Displays the current live data stream associated with the DTC

Additional data: record other data related to the fault

⚫ ACTUATION TEST (BI-DIRECTIONAL CONTROL)

Actuation test, also known as bidirectional control, is a generic term used to describe sending and receiving information
between one device and another. This function is used mainly to judge whether these actuating components of the engine
are working properly.

The vehicle engineers responsible for designing computer control systems programmed them so a scan tool could request
information or command a module to perform specific tests and functions. Some manufacturers refer to bidirectional controls
as functional tests, actuator tests, inspection tests, system tests or the like. Reinitialization and reprogramming also can be
included in the list of bidirectional controls.

This function allows the device to send information to and receive information from, vehicle control modules. For example,
in the case of OBD II generic information Mode 1 (which relates to data parameters), the scan tool user initiates a request
for information from the powertrain control module (PCM), and the PCM responds by sending the information back to the
scan tool for display. Most enhanced scan tools also can actuate relays, injectors and coils, perform system tests, etc. Users
could check the individual part to see what is working properly by actuation test.

⚫ SPECIAL FUNCTIONS

Usually, special functions provide various reset or re-learning functions menus for most vehicle systems. You can easily and
quickly solve some faults through special functions for your car. After some functions are successfully executed, fault codes
will be generated, which need to be cleared manually after the car is running for a little while which could include a single
start of the engine or multiple warm up cycles.

And under each system, you can view the special features supported by that system. Different models and systems often
have different special functions. Even for the same system of the same model, the years and ECU type may lead to different
special functions supported.

18
ECU CODING & PROGRAMMING

Since the introduction of OBD II and leading up to modern Hybrids and EVs, computers, and software in cars have been
expanding at an exponential rate. In-car software is becoming one of the leading needs for service, and updating software
may be the only way to fix some of these issues:

• Drivability
• Fuel Efficiency
• Power Loss
• Fault Codes
• Durability of Mechanical Parts

The Programming and Coding function is used to re-flash the vehicle control modules, which allows you to update the
computer software of the vehicle to the latest version, as well as to reprogram adaptive data of certain components after
making repairs or replacements.

There are two general types of programming operations:

⚫ ECU Coding

ECU Coding, also known as Teach-in Program, or Component Adaptation, is used to reprogram adaptive data for electronic
control modules after repairs or replacements of parts.

*NOTE: Codable control modules/components are system-specific, which means that not all control modules are
codable.

⚫ ECU Programming

ECU Online programming means a user could download the latest version of the software from the online server database
through Internet access (this procedure is done automatically when the tablet is connected to the Internet, so there is no
need to check for software updates yourself), and reprograms the newest version into the ECU of vehicles.

Reprogramming involves taking the following steps, but there may be changes related to the vehicle type, so please
complete the operation according to the actual situation and software prompts.

⚫ Available programming or coding operations vary by test vehicle. Only the available operations are displayed in the
tablet menu.
⚫ The programming function applies only when the vehicle is connected with a VCI device, which serves as a PassThru
interface to establish communication with and transfer data to the vehicle’s ECU.
⚫ Before applying the ECU programming function, please make sure that the tablet computer is connected to a stable
Internet connection so that the tablet computer can access the vehicle manufacturer's server for update services.
⚫ Selecting the programming or coding function will open a menu of operating options, which differs depending on the
vehicle’s make and model. Selecting a menu option either displays a programming interface or opens another menu
containing other options. When performing programming or coding operations, follow all instructions on the screen.
The way and content of the information displayed on the screen differ depending on the type of operation being
performed.

NOTE: For some vehicle brands, such as BMW, the ability to program a module is limited to the number of times it
has already been programmed and the hardware version of the control module itself.

⚫ IMPORTANT

When reprogramming onboard, please always make sure the vehicle battery is fully charged and in good working condition
to avoid the operation failure caused by the abnormal voltage below the proper operating voltage. Sometimes the failure
can be recovered, but the failed reprogramming can also cause a fault in the control module. We recommend connecting
an external battery maintainer to the vehicle to ensure a steady voltage is maintained throughout programming. The required
voltage differs by the vehicle manufacturer. Consult vehicle manufacturer for correct voltage to be maintained.

19
 Occasionally a flash update procedure may not complete properly. Common causes of flash errors include poor
cable connections between the tablet, VCI, and vehicle, the vehicle ignition being switched off before the flash
procedure is complete, or low vehicle battery voltage.

If the process quits, recheck all the cable connections to assure good communications and initialize the flash
procedure. The programming procedure will automatically repeat if the previous operation does not succeed.
Please use this feature with caution and it is not recommended for non-professionals.

3. SPECIAL FUNCTIONS
The Scan Tool supports a lot of commonly used special reset functions, allowing you to quickly access your vehicle system
for various scheduled services, maintenance, and reset performance. These functions often eliminate the need to reset
codes after resolving common problems. Since XTOOL is continuously developing, the manual may not include all of the
latest special functions that are available for download. This user manual lists some of the commonly used special reset
services for your reference.

5.1 ABS BLEEDING

Anti-Lock Braking System keeps the tires from locking up immediately when there are brakes. Keeping ABS in good
condition can give full play to the effectiveness of the brakes, shorten the braking time and distance, prevent the vehicle
from skidding and tailing during emergency braking, ensure good driving stability and steering maneuverability, and avoid
violent friction between the tires and the ground to reduce tire wear. When the ABS contains air, the ABS bleeding function
must be performed to bleed the brake system to restore ABS brake sensitivity.

ABS Bleeding can be performed in the following cases:

⚫ replace the rear brake distributor pump or the front brake distributor pump. 2.
⚫ Severe brake fluid shortage
⚫ change the brake fluid

The operation guidelines of the ABS Bleeding function are shown as below:

1. Read the operating instructions and precautions that appear on the screen carefully before performing the operation
to ensure that the equipment and car are in the correct condition
2. Attach bleeder bottle to the left rear bleeder screw.
3. Open the left rear bleeder screw.

20
4. When ready, click "OK" to enter the bleed procedure, and pumping the brake pedal continuously with steady applies
every 2 seconds during the entire procedure

5. Continue pumping the brake pedal, when air bubbles are no longer visible, select OK to enter next bleed procedure
for left front wheel

21
6. Repeat the operation 3 times to complete the bleed procedure for the left front wheel, right front wheel and right rear
wheel in turn.
7. Stop pumping the brake pedal, and close the right rear bleeder screw

8. Click OK to complete the entire bleed procedure

Caution

⚫ The ABS pump screw needs to be unscrewed

⚫ Brake fluid will be under pressure during this process. Secure the bleed hose and open bleeder screws slowly

22
⚫ Some vehicles do not support automatic bleeding, but manually bleeding

5.2 OIL RESET

The scan tool can be used to reset the engine oil life system, which calculates the optimum oil life change interval based on
the vehicle’s driving conditions and climate. The oil life reminder must be reset each time the oil is changed so that the
system can calculate when the next oil change is required.

This function can be performed in the following cases:

⚫ If the service lamp is on, you must provide service for the car. After service, you need to reset the driving mileage or
driving time so that the service lamp turns off and the system enables the new service cycle.
⚫ After changing engine oil or electric appliances that monitor oil life, you need to reset the service lamp.

The operation guidelines of the Oil Reset function are shown as below:

1. Enter the Oil Reset menu and choose relevant models according to the vehicle being tested.
2. Follow the instructions displayed that are specific to the vehicle and press OK after completing the instructions shown.

3. Enter Maintenance mileage reset menu.

4. Click INPUT and enter a reasonable value of remaining oil life and press OK.

5. Confirm the [New Value] you just entered, and then click OK at the bottom right to complete the procedure.

23
6. Message of ‘Write successfully’ displays when Oil Reset function has successfully performed.

5.3 EPB

Electronic Parking Brake (EPB) System reset is a popular special function. You can use this function to reset the electronic
parking brake system and brake pads (retraction, release of the brake pump), G-sensor and body angle calibration. This
function has multiple uses and can safely and effectively maintain the electronic brake system. These applications include
deactivating and activating brake control systems, assisting in controlling brake fluid, applying and releasing brake pads,
setting brakes after replacing brake discs or brake pads, etc.

1. If the brake pad wears the brake pad sense line, the brake pad sense line will send a signal to the onboard tablet asking
for replacing the brake pad. After replacing the brake pad, you must reset the brake pad to clear the trouble code.
Otherwise, the car continues to falsely notify the user that the brake pads are in need of replacement.

2. A reset must be performed in the following cases:

⚫ The brake pad and brake pad wear sensor are replaced.
⚫ The brake pad indicator lamp is on.
⚫ The brake pad sensor circuit is shorted.
⚫ The servo motor is replaced.

The operation guidelines of the EPB function are shown as below:

1. Enter the EPB menu and choose relevant models according to the vehicle being tested.
2. Follow the instructions displayed and press YES after completing the instructions shown.

24
3. Enter the Enter maintenance mode menu and release the handbrake brake. And press OK after completing the
instructions shown.

4. Wait until the message of ‘Successful operation’ popes up. And press OK to exit the menu.
5. Enter the Exit maintenance mode menu and wait until the message of ‘‘Successful operation’ popes up.

5.3 SAS

Steering Angle Sensors (SAS) System Calibration permanently stores the current steering wheel position as the straight-
ahead position in the SAS EEPROM. Therefore, the front wheels and the steering wheel must be set exactly to the straight-
ahead position before calibration. In addition, the VIN is also read from the instrument cluster and stored permanently in the
SAS EEPROM. On successful completion of calibration, the SAS fault codes will be automatically cleared.

To reset the steering angle, you need to first find the relative zero point position for the car to drive in a straight line. Taking
this position as a reference, the ECU can calculate the accurate angle for left and right steering.

After replacing the steering angle position sensor, replacing steering mechanical parts (such as steering gearbox, steering
column, end tie rod, steering knuckle), performing four-wheel alignment, or repairing the car body, you must reset the
steering angle.

The operation guidelines of the SAS function are shown as below:

1. Enter the SAS menu and choose relevant models according to the vehicle being tested.
2. Enter the Set steering angle sensor menu and follow the instructions displayed.

25
3. Wait until the following instruction is displayed and press Yes after completing the instructions shown.

4. Follow the instructions displayed and press OK after completing the instructions shown.

5. Wait until the following instruction is displayed and press OK after completing the instructions shown.

26
1. Message of ‘Function execution is completed’ displayed when SAS reset function has successfully completed.

5.5 BMS RESET

The Battery Management System (BMS) allows the scan tool to evaluate the battery charge state, monitor the close-circuit
current, register the battery replacement and activate the rest state of the vehicle.

This function enables you to perform a resetting operation on the monitoring unit of the vehicle battery, in which the original
low battery fault information will be cleared and battery matching will be performed.

Battery matching must be performed in the following cases:

⚫ The main battery is replaced. Battery matching must be performed to clear original low battery information and prevent
the related control module from detecting false information. If the related control module detects false information, it
will invalidate some electric auxiliary functions, such as automatic start & stop function, sunroof without one-key trigger
function or power window without automatic function.
⚫ Battery matching is performed to re-match the control module and motoring sensor to detect battery power usage more
accurately, which can avoid an error message displayed on the instrument cluster.

The operation guidelines of the BMS Reset function are shown as below:

1. Enter the BMS Reset menu and choose relevant models according to the vehicle being tested.
2. Turn on the ignition switch.
3. Press OK to continue the BMS function.
4. Enter battery capacity (within the given range) and press OK after the input.

5. Enter the battery manufacturer and press OK after the input.

27
6. Enter the 10-digit battery serial number and press OK after the input.

5.6 INJECTOR CODING

This function can write the identification code of the fuel injector into the ECU so that the ECU can recognize the new injector.

After the ECU or injector is replaced, the injector code of each cylinder must be confirmed or re-coded so that the cylinder
can better identify injectors to accurately control fuel injection.

 In general cases, there is no need to perform the coding matching function after cleaning;
 The identification of the fuel injector includes its working accuracy value and type value. When replacing an injector you need to
find the corresponding model for replacement;
 At present, mainstream cars support injector coding functions.

The operation guidelines of the Injector Coding function are shown as below:

1. Enter the Injector coding menu and choose relevant chassis models according to the vehicle being tested.
2. Enter the Fuel injection nozzle injection volume adjustment menu.
3. Read the note displayed carefully and press OK after the reading.

28
4. Read and confirm the value stored in the cylinders.

5. Enter the Change the value of cylinder menu of the replaced injector(s), enter the new 5-digit value, and then press
OK.

Wait until the message ‘Write successfully’ pops up.

6. Turn off the ignition switch.

7. Wait until the message asks you to turn on the ignition switch.
8. Re-enter the Fuel injection nozzle injection volume adjustment menu to check whether the new value(s) are shown.

29
5.7 DPF REGENERATION

The Diesel Particle Filter (DPF) function manages DPF regeneration, DPF component replacement teach-in, and DPF teach-
in after replacing the ECM.

The ECM monitors driving style and selects a suitable time to employ regeneration. Vehicles driven a lot at idling speed and
low load will attempt to regenerate earlier than vehicles driven more with higher load and speed. For regeneration to take
place, a prolonged high exhaust temperature must be obtained.

In the event of the car being driven in such ways that regeneration is not possible, i.e., frequent short journeys, a diagnostic
trouble code will eventually be registered in addition to the DPF light and “Check Engine” indicators displaying. A service
regeneration can be requested in the workshop using the diagnostic tool.

DPF regeneration is used to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode
(such as high-temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter
performance.

DPF regeneration may be performed in the following cases:

⚫ The exhaust back pressure sensor is replaced.

⚫ The PM trap is removed or replaced.
⚫ The fuel additive nozzle is removed or replaced.
⚫ The catalytic oxidizer is removed or replaced.
⚫ The DPF regeneration MIL is on and maintenance is performed.
⚫ The DPF regeneration control module is replaced.

The operation guidelines of the DPF function are shown as below:

1. Enter the DPF menu and choose relevant models according to the vehicle being tested.
2. Enter the DPF regeneration menu.
3. Read carefully and complete the requisites listed before performing the DPF regeneration function. Press OK after
completing the instructions shown.

30
4. Read the fuel tank level and make sure that it fulfills the requirement displayed.
5. Read the carbon deposit load.
6. Choose the “drive to warm up” option and follow the instructions listed below. Press OK after completing the instructions
shown.

7. Read the instructions carefully and follow the instructions shown on the screen. Press OK after completing the
instructions shown.

8. Follow the instructions displayed and press OK after completing the instructions shown. IMPORTANT: Please pay
attention to the Note.

31
9. Press the OK button to start the regeneration.

10. Wait for the value of carbon deposit to decrease until a message of ‘Emergency regeneration has been completed’
pops up, this process may take up to 40 minutes.

11. Wait for 2 minutes to let the particulate filter cool down.

32
12. Press drop out to exit the DPF function.

5.8 TPMS RESET

This function allows to perform the learning and matching and resetting functions of the tire pressure sensor.

TPMS Reset may be performed in the following cases:

⚫ Tire replacement
⚫ After troubleshooting tire pressure related problems
⚫ Other causes of loss of signal from the tire pressure sensor

1. For tire pressure sensor matching, some vehicle models may need the TPMS activation tool;
2. After learning process, you may need to run the car for some while before the fault light goes off;
3. Tire pressure imbalance may also cause the tire pressure light;
4. This function is only available for activated tire pressure sensors. If you have a brand-new sensor, please use the professional
tire pressure device.

Even for the same model, its tire pressure system may differ by the region where it is manufactured. Therefore, under the
TPMS Reset function, we provide 6 menus for the major automotive manufacturing regions, including Korea, Japan, USA,
China, Australia and Europe, as shown below.

And then please enter the sub-menu by the origin region of car make and select the vehicle model you need

33
TPMS reset can be further divided into 4 methods, such as Automatic Relearn, Static Relearn, Copy ID and OBD Relearn,
which is depending on the specific model. Also, even if the relearning methods are the same, the learning procedure may
differ.

⚫ AUTOMATIC RELEARN

1. Install tire pressure sensor appropriately

2. Adjust all TPMS sensors to the standard value
3. Keep the vehicle at a complete standstill status for more than 20 minutes (with the engine off and power off)
4. Drive at 30-100km/h for more than 15 minutes
5. The vehicle will automatically relearn the value, after that, the tire pressure warning will disappear
6. If the relearn procedure fails, please repeat steps 2-5

⚫ STATIC RELEARN

a) Install all tire pressure sensors appropriately

b) Pull up the parking brake
c) Turn the ignition to ON/RUN with the engine off
d) Enter the tire pressure learning mode through the instrument panel on vehicle. There will be the corresponding prompt,
which are differ from different car make and model, please subject to the vehicle manual or consult a professional)
e) Starting from the left front wheel (some models flash the turn signal at the corresponding position), use the TPMS
Activation Tool to activate the sensor, and the vehicle will sound the horn or flash the turn signal at the corresponding
position after successful activation.

! Note: The first sensor should be learned within 2 minutes, otherwise please repeat step 4

f) After the left front wheel sensor is successfully relearned. For the remaining, please activate the remaining tire pressure
sensors in the order of right front, right rear and left rear. The prompt and activation success status are the same as
step 5

! Note: The remaining sensor learning needs to be completed within 3 minutes, otherwise please repeat the relearn
procedure from step 4!

g) Turn the vehicle off and power off. Adjust all sensors to the standard value.
h) Tire pressure warning light will disappear after success. If procedure fails, please repeat steps 4-7

⚫ OBD RELEARN

1. A TPMS Activation Tool is needed

2. Install tire pressure sensor appropriately
3. Adjust all TPMS sensors to the standard value
4. Activate all sensors in the order of left front, right front, right rear, left rear
5. Connect TPMS Activation Tool to the OBD port of vehicle and perform the OBD relearn function to write the sensor ID
6. Turn the ignition to ON/RUN, re-trigger all sensors in the order of left front, right front, right rear, left rear
7. Keep the vehicle powered off for more than 25 minutes
8. Drive at 30-100km/h for more than 15 minutes. If relearn successful, the tire pressure warning light will go off. Otherwise,
please repeat steps 4-7

34
⚫ COPY ID RELEARN

! Note: This learning method of the vehicle can only copy ID to the new sensor through the following three methods
to replace the original sensor, if the new sensor cannot change its own ID, then the sensor can only be replaced by
the OEM equipment!

Method 1:

1. Use a TPMS Activation Tool to activate the original sensor, copy the sensor ID to the tire pressure activation device
2. And then program the copied ID into the new sensor through the TPMS Activation Tool (The binary of ID format should
be the same as the original sensor)
3. Remove the original sensor that has been just copied the ID, install the new sensor that has just been programmed,
and put the tire back on

Method 2:

1. Use the TPMS Activation Tool to connect the vehicle OBD port, enter the tire pressure system, copy the ID of the
sensor to be replaced
2. And then program the copied ID into the new sensor through the TPMS Activation Tool (The binary of ID format should
be the same as the original sensor)
3. Remove the original sensor that has been just copied the ID, install the new sensor that has just been programmed,
and put the tire back on

Method 3:

1. Remove the original sensor

2. Use the TPMS Activation Tool to copy the original sensor ID into the new sensor manually (The binary of ID format
should be the same as the original sensor)
3. Install the new sensor to the tire correctly, set the tire pressure to the standard value, and put the tire back on the
vehicle

! Note

a) Tire pressure standard is usually displayed in these places:

⚫ Vehicle owner's manual

⚫ Label next to the driver's door (near the B-pillar)
⚫ Drawer next to the driver's seat of the vehicle
⚫ Fuel tank cap

b) This Scan Tool is not a replacement for the TPMS activation tool, and it only provide TPMS Reset/Relearn
function but activation of TPMS sensors. If you need a professional TPMS activation tool, please consult your local
dealer.

6. REPORT
Diagnostic Report is used for viewing and printing the saved files, such as Live Data, Trouble codes or pictures generated
in the process of diagnosis. Users also can view a record of which cars have been previously tested. It includes 3 parts:

⚫ Diagnosis Report
⚫ Data Playback
⚫ File Manager

35
REPORT

This feature provides a history of diagnostic reports, where you can view and delete the vehicle's diagnostic reports
according to your needs.

When you finish the diagnostics progress and exit the diagnostic application specific to this vehicle, you will get a prompt of
report regeneration.

When you open the report, located in the header of the table is the workshop information you filled in advance in the system
setup, then the information of the vehicle, as shown below:

36
Note: The vehicle information is allowed to edit by clicking the pen icon on the right side of the picture shown above.

You also can click "Print PDF Report" at the bottom right corner to output the pdf report. If you need to close the report tap
on the button “Exit”.

Please follow the below steps to print your report▼

Step 1: Install an APP that can connect to your target printer. Add the printer and input the IP address of the printer in the
APP, or you can contact the XTOOL support team (support1@xtooltech/ support2@xtooltech.com) for help.

The Scan tool doesn’t provide the printer driver software, please install a third part App on the tablet if you need the print
your Diagnostic report.

Step 2: On the Android main menu, go to Settings -> Printing-> Turn printer on.

Step 3: Report-> Choose report-> Print PDF Report-> Print

Step 4: Click the top-left corner of the screen and choose the printer previously added. Then click the button on the right to
print.

REPLAY

This function allows you to replay the living data recorded during the Diagnostic process.

Before replaying the living data, please make sure you have recorded the live data during the Diagnostic

37
FILE MANAGER

This function allows you to check and delete files on the device. Please use this function under the guidance of professionals.
Ordinary users are not recommended to use it by themselves, as it may cause the removal of software or malfunctioning of
the scan tool.

7. SETTINGS
Click the Settings button to adjust the default settings and view information about the Scan tool. There are five options
available in the system settings:

⚫ Language
⚫ Unit
⚫ My Workshop Info
⚫ Bluetooth
⚫ Self-test
⚫ Firmware Information
⚫ About

LANGUAGE

The languages supported by this device are listed in Settings. In areas outside the English area, the default language is
English and the local official language. Users can switch between English and local official languages on the device by
themselves.

If you need to switch to other languages, please contact XTOOL technical support at supporting@XTOOLtech.com to
unbind the current language configuration and rebind it to the desired language configuration. After the configuration is
successfully changed, you can switch the target language.

38
 This will only change the language of the APP. If you want to change the system language, please go to Android Settings.

◼ How to change the language of your software?

➢ Step1: Contact your dealer or XTOOL Support and leave a message about the language you need and the S/N of
your device. A technician will modify the language configuration for you in the background. Wait for a response from
the technician indicating Step 1 is complete.
➢ Step2: Settings->Language->Choose language
➢ Step3: OS Settings->Language & input->Choose Language
➢ Step4: Back to Updates to pull all packages again

UNITS

You can switch the units used by the system. Scan tool provides you with Metric, Imperial, and US units. You can directly
click on the unit you need. After the switch is successful, a blue checkmark will be displayed behind the unit’s name.

BLUETOOTH

Check your VCI box Bluetooth name here and pair it

39
SELF-TEST

Please use this function to determine if the device is in good working status before diagnosing. When in use, the VCI box
needs to be powered on.

PRECAUTIONS FOR USE

⚫ Please use an external power supply to VCI box, and it is forbidden to connect the car during the self-test,
otherwise it may cause serious damage or failure of the car;

After making sure that you have not connected the device to the car, please click OK to start the self-test procedure.

40
The self-test procedure will check the communication status of each line and display it in the list as below. If the
communication status of a certain line is NG, it may affect the models based on those lines. If the self-test fails, please do
not diagnose the car with the faulty line.

MY WORKSHOP INFO

Click on My Workshop Information, you can input your workshop information here. As shown in the figure below, you need
to fill in the valid information in the corresponding column and click "SUBMIT". Then it will show your workshop information
in the report when you generate a diagnostic report, including your company name, address, website, telephone, and
mailbox.

41
FIRMWARE INFORMATION

You can view the firmware information here, including the firmware name, the latest firmware version and the currently used
firmware version.

The Diagnostic tablet supports automatic firmware update, please make sure that the device is connected to the
network when you enter the diagnostic software and the firmware will be automatically updated to the latest version.

ABOUT

Tap on ABOUT, you can check the serial number and APP version on here.

42
8. UPDATE & FACTORY RESET
UPDATE

After activating the device, please update the software modules identified in the "Updates" screen. The device will identify
all currently available software packages, and you can download them as needed. ALL software updates directly via the
Internet. To access the update application, open the Diagnostic application and click Updates to enter the screen shown
below:

After contacting your XTOOL Support to change the language configuration, you need to download all the software
packages on the device again.

Cautions

When the subscription expires, the software has installed on your device itself still is available, but all updates will be invalid.
If you delete specific software due to the personal operation, XTOOL is not responsible for supporting the restoration of the
software when the subscription expires.

To renew your subscription, please contact your local dealer, or contact XTOOL technical support team directly.

43
DELETE SOFTWARE

Long-press the unwanted software until it has been selected, then click the Delete button shown on the upper part of the
screen. And you can select and delete multiple software at once.

FACTORY RESET

When you choose to restore factory settings in the Android OS system, the device will automatically erase any custom
settings and data, restart and then enter the factory reset mode.

A factory reset is triggered by clicking the Settings mode from the main home page, and then clicking on “Backup & reset”.
Follow onscreen prompts to initiate the factory reset process.

Once the scan tool resets to factory default settings it will start up and then you can select the language in the following
interface.

After selecting the system language, click Next to enter the Wi-Fi connection page, as shown below:

44
Select a network to connect to on the Wi-Fi connection page. You will need to enter the Wi-Fi password to establish Wi-Fi
connectivity.

After successfully connecting to an Internet network connection, the scan tool will jump to Factory mode to download the
software:

This download process can take several minutes, largely determined by the speed of your Internet connection. Do not power
off the scan tool or walk out of range of the Wi-Fi connection during this period.

Once the software has been downloaded, the tablet will automatically reboot and request the system language selection
again.

45
Since restoring the factory settings will erase the user information on your device, you need to enter the email again to
activate your device.

9. FAQ
Q1: FAILED TO GENERATE DIAGNOSTIC REPORT

1. Currently only the following diagnostic functions trigger a diagnostic report: read ECU information, read code and clear
code, live data, and freeze frame. Other functions such as immobilization and maintenance services will not generate
a diagnostic report.
2. After entering the Diagnostic menu, you need to perform one specific function before the system can generate a
Diagnostic report.
3. After the Diagnostic test is completed, you need to go back to the previous menu step by step to generate the Diagnostic
report successfully. If the APP is killed directly, the report cannot be triggered.
4. If the report still cannot be generated after troubleshooting according to the above prompts, please try to exit the APP,
enter the system settings, and then choose to clear the APP cache, following the below path: Android System
Setting>>Apps>>Diagnosis>>Clear Cache

Q2: HOW TO PRINT A DIAGNOSTIC REPORT

The XTOOL device is compatible with third-party print drivers. You can download the printer driver you need in the browser
that comes with the tablet to install it, and then set your printer in the OS settings. After the configuration is completed, you
can print Reports.

Q3: FAILED TO EXTRACT FILES

Since the XTOOL tablet is equipped with an Android system, you have to confirm the system type of receiver.

For Android: supports transferring files via Bluetooth, USB cable, etc.;

For IOS: only supports transferring files through a wired connection (Bluetooth connection is not available).

Q4: MAILBOX SUPPORTED

The Diagnostic tablet supports various mailboxes, including Hotmail, outlook, yahoo and Gmail, etc. When you set up an
email client, please make sure that the email client configuration address you entered is correct.

Due to the adjustment of Google's security policy, from May 31, 2022, the Android system of this device will no longer
support users logging into their Gmail accounts in the mail client.

To use the Gmail mailbox service, please log in to the web version of Gmail in the browser or use the app password for
email after turning on Google's two-step verification.

For specific steps, please contact: XTOOLonline@outlook.com

Q5: HOW TO MAKE AN APPOINTMENT FOR REMOTE SUPPORT

Please contact your dealer, or send an email to our technical support centre. (Email address: support1@xtooltech.com).
Our technical support team will confirm the time of remote support with you.

Q6: HOW TO GENERATE AND UPLOAD DIAGNOSTIC LOG FILES

The tablet will automatically generate and store diagnostic logs. When the device is connected to the Internet, it will
automatically upload all the stored diagnostic logs to the backend system.

46
Q7: HOW TO SWITCH LANGUAGE

1. Contact your dealer and leave a message about the language you need and the S/N of your device. The technician will
modify the language configuration for you in the backend system.

2. Settings->Language->Choose language

3. Back to Updates to update all the software again

Q8: FAILED TO DIAGNOSE VEHICLE

1. Contact your dealer to confirm whether the vehicle model is supported by the scan tool.

2. Check whether the vehicle is properly connected (e.g. whether the ignition is ON, and the Diagnostic of some vehicles
need to turn on the engine), If your tablet is equipped with a VCI (Vehicle Communication Interface) box, please check
the status of the VCI box indicator.

3. Confirm whether you have entered the correct Diagnostic menu.

4. Confirm whether the AUTO-SCAN function can assist you to enter the correct Diagnostic menu.

5. Check whether the software is the latest version. If not, please update to the latest version and retest.

Q9: FAILED TO ACTIVATE OR REGISTER

⚫ For ‘Activation Failed’

This error is generally caused by network instability. Please switch to a more stable network and try to activate it again.

⚫ For ‘Registration Failed’

Generally, this error is caused by a connection timeout. Please check whether you have blocked the outgoing network traffic
to non-US regions like China. We recommend that you unblock and try to register again.

Q10: FAILED TO TURN ON WHEN CHARGING

In the charging state, you need to first press the power button to light up the screen (showing the charging status). Then
press and hold the power button for 4-5 seconds until the boot animation is shown on the screen.

Q11: FAILED TO OPEN THE DIAGNOSTIC APP

The tablet has to connect to the network every 30 days, otherwise, the Diagnostic app will be locked and disabled until the
device is connected to the network. After connecting to the network, the APP will be available again. If the device is still
unavailable, please contact XTOOL technical support team for help.

Q12: CAN’T RECEIVE THE EMAIL AFTER SHARING THE DIAGNOSTIC REPORT

If your device says "Sent successfully" after you have shared the diagnostic report but your email does not receive it, this is
due to your email service provider blocking our outgoing emails in the background.

Please whitelist the following email address: feedback@XTOOLtech.com

10. WARRANTY & SERVICES

Shenzhen XTOOLtech Intelligent Co., LTD.(the Company) warrants to the original retail purchaser of this XTOOL device
that should this product or any part thereof during normal usage and under normal conditions be proven defective in material

47
or workmanship that results in product failure within ONE YEAR from the date of purchase, such defect(s) will be repaired,
or replaced (with new or rebuilt parts) with Proof of Purchase, at the Company’s option, without charge for parts or labor
directly related to the defect(s).

The Company shall not be liable for any incidental or consequential damages arising from the use, misuse, or mounting of
the device.

This warranty does not apply to:

1) Products subjected to abnormal use or conditions, accident, mishandling, neglect, unauthorized alteration, misuse,
improper installation/repair, or, improper storage;
2) Products whose mechanical serial number or electronic serial number has been removed, altered, or defaced;
3) Damage from exposure to excessive temperature or extreme environmental conditions;
4) Damage resulting from connection to, or use of any accessory or other product not approved or authorized by the
Company;
5) Defects in appearance, cosmetic, decorative, or structural items such as framing and non-operating parts;
6) Products damaged from external causes such as fire, dirt, sand, battery leakage, blown fuse, theft, or improper usage
of any electrical source.

11. REMOTE ASSISTANCE

Tap on "Remote" to start the TeamViewer quick support program, which is a simple, fast, and secure remote-control screen.
You can use this application to enable someone else to use their computer running TeamViewer software to control your
tablet over the Internet. This feature is frequently used by XTOOL's technical support centre when remotely helping
customers with technical support.

Computers and mobile devices running TeamViewer are identified by a globally unique ID. When the remote application is
started for the first time, the ID will be automatically generated according to the hardware characteristics and will not be
changed in the future. This TeamViewer ID can individually access all TeamViewer clients.

Before launching the remote desktop application, make sure that the tablet is connected to the Internet so that you can
access the tablet to receive remote support from a third party. If you encounter problems and are not able to solve them,
you could open this application and ask for remote assistance.

To obtain remote support from your partners or XTOOL AfterSalesService Center: support1@xtooltech.com |
support2@xtooltech.com

1. Turn on the power of the tablet.

2. Click Remote in the Diagnostic application. The TeamViewer screen is displayed, and the device ID will be generated.

3. Your partner must install the remote-control software on their computer by downloading the full version of the TeamViewer
program (http://www.teamviewer.com) online, and then start the software on their computer at the same time, to provide
support and remote control of the tablet.

4. Provide your ID to the partner or XTOOL technician, and then wait for them to send you a remote-control request.

5. A pop-up window will be displayed, asking you to permit the remote-control program to control your device.

6. Click Allow to accept, or click Reject to reject.

48
49
12. APPENDIX
TRADEMARKS

is a registered trademark of Shenzhen XTOOLtech Intelligent CO., LTD.

In countries where the trademarks, service marks, domain names, logos and the name of the company are not registered, XTOOL
claims that it still reserves the ownership of the unregistered trademarks, service marks, domain names, logos and the company
name. All other mproducts’ marksand the company’s name mentioned in the manual still belong to the original registered company.

You may not use the trademarks, service marks, domain names, logo and company name of XTOOL or other companies mentioned
without written permission from the trademark holder.

XTOOL reserves the right to the final interpretation of this manual content.

COPYRIGHT

Without the written consent of Shenzhen XTOOLtech Intelligent Co., Ltd., any company or individual shall not copy or backup this
operation manual in any form (electronic, mechanical, photocopying, recording, or other forms).

No part of this manual can be reproduced, stored in a retrieval system, or transmitted, in any form or by any means (electronic,
mechanical, photocopying, recording, or otherwise), without the prior written permission of XTOOL.

This manual is designed for the usage of the H6PRO MASTER Smart Diagnostic System and provides operating instructions and
product descriptions for users of this scan tool.

Use the device only as described in this manual. XTOOL is not responsible for any consequences of violating the laws and regulations
caused by using the product or its data information.

XTOOL shall not be liable for any incidental or consequential damages or for any economic consequential damages arising from the
accidents of individual users and third parties, misuse or abuse of the device, unauthorized change or repair of the device or the
failure made by the user not to use the product according to the manual.

All information, specifications and illustrations in this manual are based on the latest configurations and functions available at the
time of printing. XTOOL reserves the right to make changes at any time without notice.

BUTTON DESCRIPTION

FUNCTION BUTTONS

The following table briefly describes each function button

Item Description

Auto Scan: Quickly access the vehicle’s computer system and begin automatically diagnosing any issues.

Diagnosis: Manually scan various computer modules.

Special Functions for diagnostics

View Vehicle diagnostic reports

Remote Control: This function allows someone to remotely view the tablet screen and also issue commands to
the tablet over the Internet. This function is helpful when consulting with a colleague about a particular set of
scan tool readings.
Updates: Once the scan tool is connected to a Wi-Fi Internet connection, any available software updates are
identified on this icon. Users can upgrade the available software with one click

50
 Settings: Users can set the language, units, repair shop information and can view information about this software
Extended Functions: Users can view more extended functions and can use this function to bring up a web
browser to aid the user when researching various trouble codes.

NAVIGATION BUTTONS

The navigation bar buttons are located at the bottom of the screen, as described in the table below:

Items Descriptions

Press for screenshot

Decrease volume

Increase volume

Back to the previous interface

Shows recently used applications

Back to the main interface of the Android system

Showing the Bluetooth states

Diagnostic Application: Click this button to display the diagnostic vehicle interface

Press for screen recording

NOTIFICATION BAR

Slide down to open the notification bar. Then tap the Notification bar that newly appeared. Users can adjust the brightness of the
screen when they need it, and you can also connect to Wi-Fi and enable Airplane mode.

51
SHENZHEN XTOOLTECH INTELLIGENT CO., LTD
COMPANY ADDRESS: 17&18/F, BUILDING A2, CREATIVITY CITY, LIUXIAN AVENUE, NANSHAN DISTRICT, SHENZHEN, CHINA
FACTORY ADDRESS: 2/F, BUILDING 12, TANGTOU THIRD INDUSTRIAL ZONE, SHIYAN STREET, BAOAN DISTRICT, SHENZHEN, CHINA
SERVICE-HOTLINE: 0086-755-21670995/86267858
EMAIL: MARKETING@XTOOLTECH.COM
FAX: 0755-83461644
WEBSITE: WWW.XTOOLTECH.COM

52