CRUISE CONTROL – CLUTCH SWITCH CC–39

CLUTCH SWITCH
CRUISE CONTROL SYSTEM

COMPONENTS

NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

8.4 (86, 74 in.*lbf)

MAIN BODY ECU

(DRIVER SIDE J/B)

15 (155, 11)
INSTRUMENT PANEL CLUTCH SWITCH
SIDE BRACKET CONNECTOR
CLUTCH SWITCH
ASSEMBLY
CC

LOWER INSTRUMENT PANEL LH

LOWER INSTRUMENT
PANEL FINISH PANEL
SUB-ASSEMBLY LH

HOOD LOCK CONTROL

LEVER SUB-ASSEMBLY

x2 FRONT FLOOR FOOTREST

FOOTREST CLIP
CLIP

COWL SIDE TRIM

FRONT DOOR SCUFF PLATE LH
BOARD LH

N*m (kgf*cm, ft*lbf) : Specified torque

E129561E01
 CC–40 CRUISE CONTROL – CLUTCH SWITCH

REMOVAL
1. DISCONNECT CABLE FROM NEGATIVE BATTERY
TERMINAL
2. REMOVE FRONT DOOR SCUFF PLATE LH (See page
ME-59)
3. REMOVE FRONT FLOOR FOOTREST (See page IR-2)
4. REMOVE FOOTREST CLIP (See page IR-2)
5. REMOVE COWL SIDE TRIM BOARD LH (See page
ME-59)
6. REMOVE NO. 1 INSTRUMENT PANEL REGISTER
ASSEMBLY (See page IP-13)
7. SEPARATE HOOD LOCK CONTROL LEVER SUB-
ASSEMBLY (See page IP-13)
8. REMOVE LOWER INSTRUMENT PANEL FINISH
PANEL SUB-ASSEMBLY LH (See page IP-14)
9. REMOVE LOWER INSTRUMENT PANEL LH (See
CC page IP-14)
10. REMOVE INSTRUMENT PANEL SIDE BRACKET
(a) Remove the bolt and remove the instrument panel
side bracket.

E129555

11. SEPARATE MAIN BODY ECU (DRIVER SIDE J/B)

(a) Remove the 2 nuts and separate the main body
ECU.

E129556

12. REMOVE CLUTCH SWITCH ASSEMBLY

(a) Disconnect the connector.
(b) Loosen the nut and remove the clutch switch
assembly.

E129557
 CRUISE CONTROL – CLUTCH SWITCH CC–41

INSPECTION
1. INSPECT CLUTCH SWITCH
(a) Remove the clutch switch.
(b) Measure the resistance and check that the results in
accordance with the value(s) in the table below.
Standard resistance
Tester Connection Condition Specified Condition
Switch pin released
1-2 (Clutch pedal 10 kΩ or higher
depressed)
Switch pin pushed in
1-2 Below 1Ω
(Clutch pedal released)

Pushed In Released If the result is not as specified, replace the clutch

switch.
E129559E01

INSTALLATION
1. INSTALL CLUTCH SWITCH ASSEMBLY
(a) Fully loosen the lock nut of the clutch switch
assembly.
(b) Adjust the clutch switch until the threaded portion
CC
Cushion comes into contact with the cushion. Tighten the
lock nut and ensure that the threaded portion is in
contact with the cushion.
E129558E01
Torque: 15 N*m (155 kgf*cm, 11 ft.*lbf)
(c) Connect the connector.
2. INSTALL MAIN BODY ECU (DRIVER SIDE J/B)
(a) Install the main body ECU with the 2 nuts.
Torque: 8.4 N*m (86 kgf*cm, 74 in.*lbf)

E129556

3. INSTALL INSTRUMENT PANEL SIDE BRACKET

(a) Install the instrument panel side bracket with the
bolt.
Torque: 8.4 N*m (86 kgf*cm, 74 in.*lbf)
4. INSTALL LOWER INSTRUMENT PANEL LH (See page
IP-29)
5. INSTALL LOWER INSTRUMENT CLUSTER FINISH
PANEL SUB-ASSEMBLY (See page IP-29)
E129555
6. CONNECT HOOD LOCK CONTROL LEVER SUB-
ASSEMBLY (See page IP-30)
7. INSTALL NO. 1 INSTRUMENT PANEL REGISTER
ASSEMBLY (See page IP-13)
8. INSTALL COWL SIDE TRIM BOARD LH (See page
ME-61)
 CC–42 CRUISE CONTROL – CLUTCH SWITCH

9. INSTALL FOOTREST CLIP (See page IR-2)

10. INSTALL FRONT FLOOR FOOTREST (See page IR-2)
11. INSTALL FRONT DOOR SCUFF PLATE LH (See page
ME-61)
12. CONNECT CABLE TO NEGATIVE BATTERY
TERMINAL
Torque: 3.9 N*m (40 kgf*cm, 35 in.*lbf)

CC