26-11-08 REV C Page 1 of 7 3783048
If you have any queries regarding the installation of this product please contact the distributor from whom it was purchased, or alternatively the ARB office in your state.
Head Office ARB Corporation Ltd VIC: 42-44 Garden Street, Kilsyth, Victoria, 3137 Tel: (03) 9761 6622 Fax: (03) 9761 6807
WA: (08) 9244 3553 NSW: (02) 9821 3633 ACT: (02) 6280 7475 SA: (08) 8244 5001 QLD: (07) 3872 3872 NT: (08) 8947 2262 TAS: (03) 6331 4190
PART No 3438100
ARB NISSAN NAVARA COMBINATION BULL BAR TO SUIT BOTH
SRS AND NON-SRS EQUIPED VEHICLES.
WARNING
FOR VEHICLES EQUIPPED WITH SRS AIRBAG
WHEN INSTALLED IN ACCORDANCE WITH THESE INSTRUCTIONS, THE FRONT
PROTECTION BAR DOES NOT AFFECT OPERATION OF THE SRS AIRBAG.
TAKE NOTE OF THE FOLLOWING:
THIS PRODUCT MUST BE INSTALLED EXACTLY AS PER THESE INSTRUCTIONS
USING ONLY THE HARDWARE SUPPLIED.
IN THE EVENT OF DAMAGE TO ANY BULL BAR COMPONENT, CONTACT YOUR
NEAREST AUTHORISED ARB STOCKIST. REPAIRS OR MODIFICATIONS TO THE
IMPACT ABSORTION SYSTEM MUST NO BE ATTEMPTED.
DO NOT USE THIS PRODUCT FOR ANY VEHICLE MAKE OR MODEL, OTHER THAN
THOSE SPECIFIED BY ARB
DO NOT REMOVE LABELS FROM THIS BULL BAR.
THIS PRODUCT OR ITS FIXING MUST NOT BE MODIFIED IN ANY WAY.
26-11-08 REVB Page 2 of 7 3783048
FITTING KIT NUMBER 6171790
USE PART No QTY DESCRIPTION
4581072 4 WASHER FLAT M6 CONTROL BOX TO
CONTROL BOX BRACKET
3756293 1 CONTROL BOX BRACKET
6151021 3 BOLT M8 X 20mm
4581044 3 WASHER FLAT M8
4581046 3 WASHER SPRING M8
6151303 4 M8 CAGE NUT
EG50 1 GROMMET RUBBER
CONTROL BOX TO BULL BAR
180302 4 CABLE TIES
3756538R 1 IMPACT ABSORBER RHS
3756538L 1 IMPACT ABSORBER LHS
6151095 2 BOLT M12 X 1.25 X 35mm
4581007 4 WASHER FLAT X 1 X 4mm
4581050 2 WASHER SPRING M12
6151135 2 NUT M12 X 1.25
4581290 4 WASHER M12 X 28 X 4mm
6151089 4 BOLT M10 X 1.25 X 40mm
4581040 4 WASHER FLAT M10
IMPACT ABSORBER TO CHASSIS
4581048 4 WASHER SPRING M10
6151232 6 BOLT M10 X 1.5 X 30
4581040 12 WASHER FLAT M10
4581048 6 WASHER SPRING M10
BULL BAR TO IMPACT ABSORBER
6151026 6 NUT M10 X 1.5
6151301 2 NUT CAGE M8
6151300 4 NUT CAGE M6
6151021 2 BOLT M8 X 20mm
4581044 2 WASHER FLAT M8
4581046 2 WASHER SPRING M8
6151213 4 BOLT M6 X 20mm BLACK
4581082 4 WASHER FLAT M6 BLACK
4581287 4 WASHER SPRING M6 BLACK
6151180 8 BOLT M6 X 20mm
6151046 8 WASHER FLAT M6
6151128 8 NUT FLANGE M6
3500200 1 BUFFER KIT (LH & RH WITH FLANGE NUTS
3162455 2 PLASTIC CAPS
3751313 1 BRACKET NUMBER PLATE
6781408 1 DOUBLE SIDED TAPE
AIR GUIDE, STONE GUARD,
NUMBER PLATE TO BULL BAR
6522027 1 STONE TRAY
BLB560 3 CABLE BLACK 560mm WINCH CABLES, INDICATORS
3500080 1 ARB INDICATOR KIT
TOOLS REQUIRED, Basic tool kit, drill, 10mm drill bit and circlips pliers.
READ ALL INSTRUCTIONS BEFORE PROCEDING WITH BULL BAR FITMENT
1. Fit the M6 cage nuts to lower pan of the bull bar
and the M8 cage nuts to the impact absorbers.
1a. M6 CAGE NUTS IN LOWER PAN
1b. M8 CAGE NUTS IN IMPACT ABSORBER.
1c. TO INSERT CAGE NUTS, PUT ONE SIDE IN
AND SQUEESE WHILE PRESSING DOWN.
2. Fit buffers to the bull bar using the 8mm nyloc
nuts and heavy-duty flat washers. (Do not over
tighten)
3. Fit indicators into the bar.
4. If no winch is being fitted fit the plastic caps
into both sides of the bar. If a winch is being
installed fit a plastic cap to the LHS wing only.
5. If a winch is not being fitted place double sided
tape across the back of the number plate and
fix in place to the lower holes in the bull bar
using 2 M6 x 20mm bolts, M6 flat washers and
M6 flange nuts.
ASSEMBLY SEQUENCE FOR WINCH INSTALATION
6. Remove the cover from the control box.
Remove the three main power cables that go
from the control box to the winch and replace
with the longer cables (BLB560) from the bolt
kit. MAKE SURE THAT YOU LABEL THE
NEW CABLES THE SAME AS THE CABLES
REMOVED FROM THE CONTROL BAX.
1a 1b
1c
26-11-08 REVB Page 3 of 7 3783048
7. Fit the rubber grommet into the control box
bracket as shown opposite.
8. Fit the control box bracket to the control box
using the 4 large M6 flat washers placed either
side of the bracket and secure using the original
nuts. Finger tighten only at this stage.
9. Fit the control box cables through the rubber
grommet of the control box bracket and cable
tie together.
10. Secure the control box to the inside of the bull
bar using 3 M8 x 20mm bolts; M8 flat washers
and M8 spring washers. Finger tighten only.
11. When the control box is secured to the bull bar,
adjust the control box so that the remote cap is
central in the cutout in the wing. When satisfied
tighten the control box to control box bracket
bolts and the control box bracket to bull bar
bolts.
Insert 4 cage nuts as
shown
26-11-08 REVB Page 4 of 7 3783048
12. To place the winch clutch handle in the correct
position and for ease of operation, the handle
must be rotated 144 in a clockwise direction.
Undo and remove all the capped head screws from the
gearbox end. Gently raise the gearbox just enough to
allow rotation .DO NOT COMPLETELY REMOVE THE
GEARBOX. Refit all capped head screws and tighten.
13. Place the winch on a stand with the mounting
holes facing upwards. Lower the bull bar onto
the winch. NOTE: THE WINCH MUST BE
LINED UP SO THAT WHEN ATTACHED TO
THE BAR THE CABLE SPOOLS FROM THE
BOTTOM OF THE WINCH. Align all four holes
and secure the top holes using the hardware
supplied with the winch. Finger tighten only.
14. Remove the circlips form the lower end of the
roller fairlead and position roller fairlead over
lower holes in bull bar cutout. Secure using
hardware supplied with the winch. Tighten all
bolts.
3
26-11-08 REVB Page 5 of 7 3783048
TIGHTEN LOWER BOLTS REPLACE CIRCLIP AFTER TIGHTENING BOLTS
REMOVE LOWER CIRCLIPS PUSH ROLLER SIDEWAYS FOR CLEARANCE
15. Connect the winch control box cables to the
winch. Refer to the Warn installation instruction
manual when wiring up winch.
USING CABLE TIES ENSURE THAT ALL CABLES
ARE INSTALLED WELL CLEAR OF ALL SHARP OR
MOVING PARTS.
16. Attach the impact absorbers to the bullbar using
four M10 x 30mm bolts, M10 nuts, M10 flat and
spring washers Do not fully tighten the bolts at
this stage.
17. Remove the bumper bar from the vehicle and
discard the bolts used to hold the bumper bar in
place.
18. Using the assistance of two people, position the
bull bar over the chassis rails. Insert the square
4mm washers between the chassis and the
impact absorber and fix in place using four M10
x 40mm bolts, M10 flat and spring washers.
Tighten bolts.
19. Secure the lower bull bar mounting holes to the
vehicle tie down plates using M12 x 35mm
bolts, heavy-duty flat washers, spring washers
and 12mm nuts. Tighten bolts until the heavy-
duty washers deform.
26-11-08 REVB Page 6 of 7 3783048
20. Position the bull bar so that a uniform gap is
obtained on either side and there is between 20
and 25mm gap between the wing and the
mudguard tighten the four bolts holding the bar
to the impact absorbers.
21. Using a 10mm drill bit, drill a pinning hole
through the impact absorber using the lower
hole in the upright as a guide and then fix using
two M10 x 30mm bolts, M10 flat and spring
washers. Tighten bolts.
22. Attach the stone guard to the vehicle using four
M6 x 20mm black bolts, M6 black flat and spring
washers along the front of the stone guard and
two M8 x 20 mm bolts M8 flat and spring
washers underneath.
FUNCTION
INDICATOR
HARNESS
VEHICLE
HARNESS
EARTH
BROWN
BLACK
AMBER
LENSE
BLUE
GREEN
23. Connect the wires of the indicator harness
supplied to the wires on the vehicles
combination lamp as per the table opposite
using the scotch locks provided.
NOTE: Remove the vehicles combination lamps as
follows. Remove the bolt from the top of the lamp into
the headlamp body. Remove the grill and the two bolts
located on the inside edge of the headlamp body.
Carefully pull the lamp forward. Cable tie any excess
wire harness to the hole located on the return fold of the
bar below the headlight.
Mounting holes for the use of a high lift jack
have been incorporated on both sides of the
bull bar.
26-11-08 REVB Page 7 of 7 3783048
