PAGE NO ITEM NO DESCRIPTION UNIT BoQ QTY

144 BILL NO 19

144 PLUMBING & DRAINAGE (PROVISIONAL)

144 NOTE: Tenderers are advised to study the "Specification of

Materials and Methods to be used" (PW371, fourth revision
October 1993), before pricing this Bill.

144 NOTE: All items marked "LI" are to be executed using labour
intensive construction methods

--------------------------

144 STORMWATER DRAINAGE

144 (Haylett Formula Work Group No 146)

144 NOTE: Backfill to trenches to be 150mm selected granular

cradle compacted to 100% Mod AAHSTO, 450mm deep
selected granular fill in 150mm layers to 95% Mod AASHTO,
backfill from trenches for balance of fill to 90% Mod AASHTO in
150mm layers

-----------------

144 STORMWATER REMOVAL

144 Class 50 D precast pipe

144 1 600mm Diameter pipe laid to a slight fall in ground, including m 12

excavations not exceeding 1 metre deep (LI)

144 2 Ditto, exceeding 1 and not exceeding 2 metres deep (LI) m 46

144 Catchpits

144 3 Stormwater catchpit, size 600 x 600mm with and including light No 2
duty square dished grating cover and frame as "Besaans du
Plessis 2952" not exceeding 1 metres deep (LI)

145 Sundries

145 4 Stormwater pipe wing wall consisting of a 125mm thick surface No 2

 bed (25 MPa/20) on compacted fill, with 220mm brick wing wall
pointed on all exposed surfaces, and with 220mm wide brick on
edge coping (See detail at the back of these Bills of Quantites)

145 SOIL DRAINAGE

145 NOTE: The Contractor must allow for the removal of natural
earth seepage water that may occur during the excavation of
the trenches for the soil drainage.

Pipes shall rest on solid ground and, where necessary, pockets

of sufficient size shall be cut around joints to enable the jointing
to be properly performed. Backfilling to trenches according to
Engineer's specification.

Sewers are to be laid in accordance with SABS 1200 LD.

Bedding to be in accordance with SABS 1200 LD

Trenching to be in accordance with SABS 1200 DB

145 UPVC Pipes Class 34

145 5 50mm Pipes vertically or ramped to cleaning eyes etc. (no m 2

excavation)

145 6 110mm Ditto (ditto) m 100

145 7 110mm Pipes laid in and including trenches not exceeding 1 m 42

metre deep (LI)

145 8 110mm Pipes laid in and including trenches exceeding 1 and m 461
not exceeding 2 metres deep (LI)

146 9 50mm Pipes laid in and including trenches exceeding 2 and not m 2
exceeding 3 metres deep

146 10 110mm Ditto m 74

146 Extra on UPVC pipes for

146 11 50mm Bend No 1

146 12 110mm Bend No 102

146 13 110mm Junction No 1

146 14 110mm Access junction No 63

146 15 110mm Access reducing junction No 1

146 16 110mm "Polyflor Polydrain" floor drain No 3

146 Inspection chambers formed of 250mm thick

concrete bottom and 1000mm precast concrete
rings, the bottom steeply benched up in cement
concrete to sides of manhole from edges to
channels and with 170mm thick precast concrete
(Class C) top, finished on exposed surfaces in
untinted granolithic with angles rounded and
rebated for and fitted with manhole cover and
frame, with cover bedded in tallow and frame in
cement mortar

146 17 Inspection chamber not exceeding 1m deep internally, with No 1

Bezaans du Plessis Product No 2130 SABS 558 type 9B cover
and frame (LI)

147 18 Ditto, exceeding 1 and not exceeding 2 metres deep (LI) No 13

147 19 Ditto, exceeding 2 and not exceeding 3 metres deep No 1

147 20 Ditto, exceeding 1 and not exceeding 2 metres deep, but built No 2
over existing municipal sewer line (LI)

147 Gulleys with grating, precast concrete dish, etc.

147 21 110mm Gulley not exceeding 1 metre deep No 28

147 Sundries

147 22 Concrete (Class C) encasing to horizontal 110mm pipe m 22

including all excavations and formwork

147 23 Concrete (Class C) encasing to 50 and/or 110mm vertical pipe m 102

including all excavations and formwork

147 24 Extra over excavations in earth for pipe trenches, chambers, m3 67

etc. for excavation in soft rock
147 25 Extra over excavations in earth for pipe trenches, chambers, m3 34
etc. for excavation in hard rock

147 26 300 x 300mm Precast concrete inspection eye marker slab set No 46
in ground

147 27 110mm Cast iron "ABC" cleaning eye with and including No 19
concrete collar (See detail at the back of these Bills of
Quantities)

148 28 Determine position and excavate for connection of 110mm No 1

UPVC pipe to existing manhole, exceeding 1 and not exceeding
2 metres deep (LI)

148 29 Allow for keeping all excavations free from water and mud Item 1

148 30 Provide all necessary apparatus for and allow for the testing of Item 1
the entire drainage system to the full satisfaction of the
Architect and the Authorities, and leave perfect, any defective
work is to be taken out and replaced at the Contractor's
expense

148 31 Provide the sum of R 20 000.00 (Twenty Thousand Rand Only) Item 1
for a new municipal connection

148 WATER SUPPLIES

148 NOTE: Tenderers are advised to study the "Specification of

Materials and Methods to be used" (PW371, fourth revision
October 1993), before pricing this Bill.

-----------------------------------

148 NOTE: The Contractor must allow for the removal of natural
earth seepage water that may occur during the excavation of
the trencheds for the water supply

Pipes shall rest on solid ground and, where necessary, pockets

of sufficient size shall be cut around joints to enable the jointing
to be properly performed. Backfilling to trenches according to
Engineer's specification (See stormwater drainage)

Piping to be laid in accordance with SABS 1200 L.

Bedding to be in accordance with SABS 1200 LB.

 Trenching to be in accordance with SABS 1200 DB.

149 Polycop pipes

149 32 22mm Pipe laid in and including trenches not exceeding 1 m 5

metre deep (LI)

149 33 42mm Ditto (LI) m 2

149 Extra for pressure fittings

149 34 22mm Fittings No 9

149 35 28mm Fittings No 1

149 36 42mm Reducer No 1

149 37 42mm Bend No 2

149 38 Connection of 22mm Polycop pipe to 160mm UPVC Class 9 No 2

pipe

149 39 Connection of 42mm Polycop pipe to 160mm UPVC Class 9 No 1

pipe

149 UPVC PIPES (CLASS 9)

149 40 110mm Pipe laid in and including trenches not exceeding 1 m 40

metres deep (LI)

149 41 160mm Ditto (LI) m 443

150 Extra for pressure fittings

150 42 110mm "Duraflow" ninety degree long radius bend No 8

150 43 160mm "Ditto" No 6

150 44 110mm "Duraflow" T-piece No 3

150 45 160mm "Ditto" No 1

150 46 Connection of 110mm UPVC pipe to 160mm UPVC pipe No 3

150 47 Connection of 160mm UPVC pipe to 160mm water meter No 2

150 48 Expose and connect 160mm UPVC pipe to existing municipal No 1

water supply line

150 Taps, etc. including joints to UPVC pipe unless

otherwise described

150 49 22mm Brass gate valve with connection to polycop pipe No 2

150 50 42mm Ditto No 1

150 51 160mm Non-return valve No 2

150 52 160mm One way valve No 1

151 53 110mm Brass gate valve No 6

151 54 160mm Ditto No 1

151 55 Cast iron stop cock box as "SABS 558 Type 11A" including all No 3
brickwork excavations, etc.

151 56 Valve manhole 670mm diameter built of 220mm brickwork for a No 10

height of 400mm and one precast concrete manhole ring
670mm diameter and 375mm high, including lockable precast
concrete lid and class C concrete footing, size 750mm diameter
x 150mm thick, mesh reinforced with type 193 mesh, including
Class C concrete pedestal under valve, including excavations
and backfilling (LI)

151 57 Valve manhole, size 1020 x 1020 x 1200mm deep, built of No 1

220mm brickwork, plastered full depth inside and 500mm high
along perimeter, including lockable SABS 558 type 9B cast iron
cover and frame, and Class C concrete lid slab, size 1460 x
1460 x 150mm thick with twelve Y10 reinforcing bars 1380mm
long and Class C concrete, size 1750 x 1750 x 150mm thick
mesh reinforced with type 193 mesh, ditto (LI)

151 58 160mm Approved water meter No 1

151 The following in high level tank

151 59 "Abeco Tanks" or other approved modular pressed sectional No 1

steel watertank, size 4.88 x 4.88 x 3.66 panels high, each panel
 1220 x 1220mm high, with dust proof roof and ladder, including
unions for 160mm supply with 160mm copper ball valve (600
KPa), one 65mm scoure pipe with blank flange, one 110mm
and one 160mm outlet and manhole, fixed in position on
concrete stub walls (elsewhere measured)

152 Sundries

152 60 Concrete thrust blocks at fittings of pressure pipes including all m3 10

excavations, formwork, etc.

152 61 Provide all necessary apparatus for and allow for the testing of Item 1
the entire water supply to the full satisfaction of the Architect
and the Authorities, and leave perfect, any defective work is to
be taken out and replaced at the Contractor's expense

152 62 Allow the amount of R47 500.00 (Forty Seven Thousand Five Item 1
Hundred Rand Only) for the supply and installation of the
domestic water pump set, including all valves, flanges, etc

152 63 Allow profit on above if required Item 1

152 64 Attendance Item 1

152 65 Standard Class C precast concrete pipeline marker 1500mm No 16

long with four 6mm reinforcing rods along length and 4mm
spiral reinforcing strips at 300mm centres, with bevelled edges
to top, including four stencilled letter carved into one side,
placed vertically into ground and exposed 750mm high painted
with yellow road marking paint, including excavation, ramming,
etc.

152 WATER SUPPLIES TO FIRE APPLIANCES

152 UPVC pipes (Class 16)

152 66 110mm Pipe fixed to wall m 4

152 67 110mm Pipe fixed to steel tank m 2

153 68 110mm Pipe cast into concrete pedestal (elesewhere m 4

measured)

153 69 110mm Pipe laid vertical in ground (no excavations) m 3

153 70 110mm Pipe laid in and including trenches not exceeding 1 m 224
meter deep

153 Extra for pressure fittings

153 71 110mm "Duraflow" ninety degree long radius bend No 12

153 72 110mm "Duraflow" T-piece No 1

153 Taps, etc. including joints to UPVC pipes unless

otherwise described

153 73 110mm Brass gate valve No 2

153 74 Connection of 110mm UPVC pipe to 65mm brass pipe No 2

153 75 Connection of 110mm UPVC pipe to pressed steel water tank No 1

153 76 Connection of 160mm UPVC pipe to pressed steel water tank No 2

153 FIRE APPLIANCES, ETC. H1 0

153 77 65mm Brass right angle hydrant valve with lockable cap and No 2
chain and 6 keys

154 78 65mm Diameter snap on fire hose 30m long (supplied to client) No 2

154 79 Approved fire hose cupboard fixed to wall No 2

154 Fire hydrant pedestals

154 80 Concrete Class C hydrant pedestal 1100mm high cast around No 2

vertical pipe with bottom 300mm below ground, 340 x 340mm
square at base and tapering to octagonal shaped top 210 x
210mm overall including necessary excavation, formwork and
two coats of roadmarking paint to exposed surfaces

154 Sundries

154 81 Concrete thrust blocks at fittings of pressure pipes including all m3 4

excavations, formwork, etc.

154 82 Allow the amount of R75 000.00 (Seventy Five Thousand Rand Item 1
Only) for the supply and installation of the fire water pump set,
including all valves, flanges, etc
154 83 Allow profit on above if required Item 1

154 84 Attendance Item 1

154 85 Provide all necessary apparatus for and allow for the testing of Item 1
the entire fire water supply to the full satisfaction of the
Architect and the Authorities, and leave perfect, any defective
work is to be taken out and replaced at the Contractor's
expense

155 WASTE DRAINAGE

(Haylett Formula Work Group No 148)

UPVC piping

SANITARY PLUMBING

155 Unplasticised polyvinyl chloride piping for sanitary plumbing to

comply with SABS Specification 967 and must be clean,
smooth and free from internal and external grooving, spils,
laminations or other defects, jointed with approved liquid soap,
all in accordance with SABS specification 0112 and methods
required by and material supplied by Manufacturers.

---------------------------------------

155 86 40mm Diameter waste or ventilation pipes to walls m 149

155 87 50mm Ditto m 48

155 88 110mm Ditto m 80

155 89 50mm Ditto, cast in concrete floor m 3

155 90 110mm Ditto m 4

155 Extra on UPVC piping for

155 91 40mm Bend No 15

155 92 50mm Ditto No 7

155 93 110mm Ditto No 1

156 94 40mm Bend with inspection eye No 55

156 95 50mm Ditto No 22

156 96 110mm Ditto No 37

156 97 50mm Junction No 2

156 98 110mm Ditto No 1

156 99 40mm Junction with inspection eye No 7

156 100 50mm Ditto No 2

156 101 110mm Ditto No 3

156 102 110mm Reducing junction with inspection eye No 1

156 103 110mm Straight pan connector No 34

156 104 110mm P-trap No 1

156 105 110mm Stub stack No 7

156 106 110mm Anti-vac seal No 6

157 107 Spaly cut end to 40mm pipe No 32

157 108 Splay cut end of 50mm pipe No 11

157 Traps, etc.

157 109 50mm Flexitrap No 1

157 110 32mm Chromium plated bottle trap No 34

157 111 38mm Ditto No 7

157 112 32mm Chromium plated waste union with "anti theft" plug and No 27
chain

157 113 38mm Ditto No 6

157 114 38mm Brass shower trap with chromium plated grating No 7
157 115 38mm Chromium plated bath waste union with overflow and No 2
"anti theft" plug and chain

157 Sundries

157 116 Junction of 32mm brass to UPVC piping No 45

157 117 Junction of 38mm brass to UPVC piping No 39

158 118 Provide all necessary apparatus for and allow for the testing of Item 4
the whole of the sanitary plumbing to the full satisfaction of the
Architect and the Authorities and leave perfect, any defective
work is to be taken out and replaced at the Contractor's
expense

158 SANITARY FITTINGS

158 Accessories to all sanitary fittings to be best quality chrome

plated, unless otherwise described, all to the architect's
approval

Trade names only inserted for purpose of reference of types of

fitting or component, other brand names could be submitted for
prior approval of the Representative/Agent

Silicone sealer around all fittings

---------------------------------------

158 119 510 x 405mm "Vaal Hibiscus" white vitreous china basin, with No 1
one taphole, "Cobra 515-21" elbow action mixer and "309" anti
theft plug and "301" waste coupling fixed with "8448Z0"
brackets

158 120 "Jika Dino" white vitreous china basin with one taphole, size No 3
405 x 340mm, with "Geberit HyTouch 26" chromium plated self
closing tap with internal mixer (Art No. 115.720.21.1), anti theft
plug and chromium plated waste coupling, fixed to wall

158 121 "Jika Ibon" white vitreous china basin with one taphole (Code No 4
8.1301.0), 520mm diameter, with "Geberit HyTouch 26"
chromium plated self closing tap with internal mixer as before,
anti theft plug and chromium plated waste coupling, fixed to top
of vanity slab (elsewhere measured)
158 122 "Jika Mio" white vitreous china basin with one taphole (Code No 5
L8.1071.2), size 550 x 420mm, with "Geberit HyTouch 26"
chromium plated self closing tap with internal mixer as before,
anti theft plug and chromium plated waste coupling, fixed to
wall

159 123 585 x 435mm "Vaal Hygia" hospital basin (45021) with two No 1
tapholes, 15mm quarter turn wrist action mixer with swanneck
swivel spout outlet and hook (515/053232H21), chromium
plated waste coupling with overflow pipe, fixed to wall

159 124 "Jika Dino" wall hung toilet suite (Code 8.23317.0) with "Geberit No 15
Kombifix" concealed cistern (Art No. 110.755.001) with highline
vandal resistant flush/stop actuator (Art No. 115.151.00.1) in
stainless steel finish, with "Duroplast" seat and cover with
antibacterial coating (Code 8.9337.0)

159 125 "Jika Golem" wall urinal with concealed water inlet and waste No 2
outlet (Code 8.4306.1), size 305 x 340 x 535mm high with and
including urinal installation set (Code L8.9034.9), urinal siphonic
trap (Code G152.983.00.1) and rubber seal (Code
G119.669.00.1), fixed to wall

159 126 520 x 420mm "Citimetal WB001" wash hand basin with 25mm No 8
splashback and tiling key with and including one 15mm "Cobra
Watertech Mastermatic" metered pillar tap, fixed to wall

159 127 420 x 340mm "Franke Oval B" wash hand basin with one No 19
15mm "Cobra Watertech Mastermatic" metered pillar tap, fixed
to wall

159 128 "Franke" WC pan (Code 356003) with 110mm P-trap and back No 22
entry flush pipe, size 378 x 850 x 420mm, fixed to wall and floor
with 6mm stainless steel anchor bolts

159 129 "Franke TU 101" trough urinal, size 2600 x 780 x 290mm deep, No 1
with two flush pipe couplings, 70mm chromium plated outlet
and tile key to back and both sides

160 130 "Franke SLH" high level cistern with Beta valve and pull chain, No 2
15mm diameter brass ball valve and 1700mm bent stainless
steel flush pipe, fixed to wall
160 131 "Franke CH" slop hopper, size 540 x 540 x 565mm high, with No 1
100mm integral splashback, 38mm diameter x 250mm long
vertical flushpipe, fixed to wall

160 132 "Franke" bath, size 1800 x 760 x 403mm deep with two tap No 2
holes

160 133 "Splashworks Type E" double bowl washtrough, size 1025 x No 2
458 x 285mm high (Code W72), fixed to wall

160 134 "Citimetal DC7" drinking fountain, size 340 x 350 x 125mm No 1
deep, with 15mm push button tap and 38mm chromium plated
brass outlet, built flush into and including recess in wall

160 135 "Vulcan SCBS" single bowl preparation sink (Code 3044362), No 1
size 1650 x 650 x 1060mm high

160 136 "Vulcan DCBPS" double bowl pot sink (Code 3044435), size No 1
2250 x 650 x 1060mm high

160 137 "Vulcan Basic IM14PL" refrigeration unit, size 1400 x 715 x No 1
2050mm high

160 138 "Vulcan Electric Ranges R-E2/2 2 Solid Top 2 Solid Round No 2
Electrical" range with oven

161 139 "Vulcan Counter-Line BMHC 1800E Bain Marie" hot cupboard No 1
with all optional extras (Code 3018922)

161 140 "Speed Queen SC80" front loader washer with stainless steel No 2
tub, size 1054 x 1311 x 1422mm high

161 141 "Speed Queen ST075" tumbler with micro display control and No 2
34 kg capacity, size 981 x 1346 x 1946mm high

161 WATER SUPPLIES

161 Copper piping (Class II according to SABS 460)

161 142 54mm Waterpipe fixed to wall m 6

161 143 15mm Waterpipe in walls m 250

161 144 22mm Ditto m 83

161 145 28mm Ditto m 4

161 146 35mm Ditto m 8

161 147 15mm Waterpipe in wall with and including wrapping with m 83
petrolatum anti corrosion tape and primer

161 148 22mm Ditto m 62

161 149 15mm Waterpipe in ceiling m 4

162 150 22mm Ditto m 100

162 151 28mm Ditto m 10

162 152 22mm Waterpipe fixed to top of slab in roof space m 28

162 153 28mm Ditto m 177

35mm m
162 154 54mm Ditto m 71

162 Extra on copper piping for Connex compression

fittings

162 155 15mm Fittings No 404

162 156 22mm Ditto No 294

162 157 28mm Ditto No 202

28/22 Reducer
162 158 35mm Reducer No 24

162 159 42mm Reducer No 24

162 160 35mm Bend No 5

162 161 54mm Bend No 10

163 162 54mm T-piece No 1

163 163 54mm Reducing T-piece No 24

163 Service pipes, stop cocks, taps etc.

163 164 15mm Copper service pipe, 550mm girth No 66

163 165 22mm Ditto No 8

163 166 28mm Ditto No 5

163 167 15mm "Ballostop" and joints to copper piping No 44

163 168 22mm Brass stop cock No 5

163 169 28mm Ditto No 9

163 170 22mm Bib tap with hose connection No 10

163 171 15mm "Star" chromium plated undertile stop cock No 2

163 172 15mm "Star" chromium plated bibtap with hose connection and No 12
tile flange

163 173 15mm Chromium plated elbow action wall type mixer with No 1
swanneck swivel and hook

164 174 15mm "Cobra Watertech Mastermatic KM 2.101" chromium No 5

plated metered pillar tap

164 175 20mm Ditto No 4

164 176 22mm "Flushmaster Junior FJ4.001" valve No 22

164 177 35mm "Flushmaster FM.100" valve No 1

164 178 15mm "Cobra KM2.301 Mastermatic" undertile metering No 16

stopcock with non hold open feature, flow controller and
adjustable cycle time

164 179 15mm "Cobra Vandalmaster KP2.6" chromium plated shower No 17

rose

164 180 "Geberit UR22 Mambo" stainless steel pneumatic urinal flush No 2
valve (Art No. 115.828.00.1) including housing (Art No.
115.801.00.1)

164 181 32mm Thermostatic blender (Code KD2.204) No 4

164 Sundries
164 182 Connection of 15mm copper pipe to 22mm polycop pipe No 1

164 183 Connection of 22mm copper pipe to 110mm UPVC Class 9 No 2

pipe

165 184 Connection of 28mm copper pipe to 110mm UPVC Class 9 No 1

pipe

165 185 Connection of 54mm copper pipe to 110mm UPVC Class 9 No 1

pipe

165 186 "Thermoflex Ziplock" to 15mm copper pipes m 4

165 187 "Ditto" to 22mm copper pipes m 98

165 188 "Ditto" to 28mm copper pipes m 187

165 189 "Ditto" to 54mm copper pipes m 71

165 190 Provide all necessary apparatus for and allow for the testing of Item 4
the whole of the sanitary plumbing to the full satisfaction of the
Architect and the Authorities and leave perfect, any defective
work is to be taken out and replaced at the Contractor's
expense

165 ELECTRIC HOT WATER GEYSER

165 191 "Kwikot Prisma Supreme" or other approved 10 litre under No 1

counter hot water geyser, including vacuum breaker and
presuure release valve, complete with brackets, bolts, etc.
hoisting and fixing in position

165 192 "Kwikot Megaflow" or other approved 50 litre horizontal type hot No 1
water geyser, ditto

165 193 "Ditto", but 100 litre geyser No 1

166 194 "Ditto, but 200 litre geyser No 1

166 195 "Ditto", but 300 litre geyser m2 4

166 196 22mm "Kwikhot Pro Clean" sediment filter (600KPA) No 8

166 197 Approved polyethylene drip tray size 1820 x 560mm wide No 8
166 198 20mm PVC overflow pipe m 26

166 Sundries

166 199 Provide all necessary apparatus for the testing of the whole Item 4
water supply system to the satisfaction of the Architect and the
Authorities and leave perfect, any defective work is to be taken
out and replaced at the Contractor's expense

166 FIRE SERVICE

166 Galvanised mild steel piping

166 200 25mm Water pipe fixed to walls m 16

166 201 32mm Ditto m 4

166 202 32mm Water pipe in ceilings m 22

166 203 25mm Waterpipe fixed to top of slab in roof space m 16

167 204 32mm Ditto m 24

167 Extra on galvanised mild steel piping for

167 205 32mm Reducer No 3

167 206 25mm Fittings No 11

167 207 32mm Bend No 6

167 208 32mm T No 3

167 Sundries

167 209 Junction of 25mm galvanised mild steel piping to fire hose reel No 4
(elsewhere measured)

167 210 Junction of 32mm galvanised mild steel pipe to 110mm UPVC No 2
pipe

167 Fire extinguishers, hose reels, etc.

167 211 4,5kg CO2 fire extinguisher complete with charge, top and No 13
bottom hanging brackets and backplates and fix in position,
 including bolting backplate to wall

168 212 Approved automatic fire hose reel, complete with 30 metre No 4
length of 19mm diameter pressure hose with chromium plated
shut off nozzle and brackets, chromium plated universal
mounted swivelling pulley, 25mm chromium plated hydrant
valve with wheel-head pressure gauge, fixing brackets, bolts,
etc. and fix into position on face of wall including building bolts
into brickwork in cement mortar, bolting hose reel and hose
guide to wall, connecting up 25mm galvanised mild steel supply
pipe (elsewhere measured) the whole to comply with the
Municipal Fire Regulations
RATE CERT AMOUNT

0.00

0.00

0.00
100.00

42.00

461.00

2.00

74.00

102
 1

63

1.00

4.00

9.00

18.00

20.00
 9

40.00

443.00

3
 2

1.00
0.00
0.00

0.00
0.00

0.00

0.00
0.00

0.00

0.00

0.00

0.00