Flexi Remote Radio Head 8TX 2600 (FZHI)
FZHI technical specifications.
Functional description
Table: FZHI functional specification
Property Value
Output power 8x20 W
Configurable power levels 5, 10, 15, 20 W
MIMO no
Outdoor installation yes
Beamforming yes
Supported technology TD-LTE
Frequency range 2575 - 2615 MHz
Instantaneous bandwidth 40 MHz
Supported bandwidths 10, 20 MHz
Interfaces
Figure: FZHI interfaces
FZHI interfaces
Table:
Label on Number of
Interface Connector type Additional info
the HW interfaces
Power supply DC IN 1 3-pole screw Power delivery
terminal
Grounding 2 M5 screw
terminals
Antenna connector ANT 8 N type RF signal interface to
connector antenna(s)
Calibration BF 1 N type Beamforming
connector calibration
Remote Electrical Tilt RET 1 RS485 AISG RET modem with
DC feed
External Alarm Connection EAC 1 RJ45 External Alarm input
Optical interface OPT 4 SFP OBSAI, 4 x 6.144 Gbps
Functional block diagram
Figure: FZHI functional block diagram
Electrical specifications
Table: FZHI electrical specifications
Value
Nominal supply voltage -48.0 V DC
Nominal input voltage range -40.5 V DC to -57.0 V DC
Extended input voltage range -36.0 V DC to -60.0 V DC
This module contains an integrated overvoltage protection (OVP).
Power consumption
Table: FZHI power consumption
Estimated power consumption [W] at 48 V DC input at 23°C. Non-
committed estimated values depend on the final product HW and
RF output SW optimization with +/-10% margin.
Number of TXs power per TX
[W]
55% TX duty 68% TX duty
8 20 635 684
10 449 494
5 355 391
2 287 311
6 20 515 552
10 370 417
5 299 337
2 255 282
4 20 394 419
10 290 339
5 243 282
2 223 253
2 20 276 289
10 218 263
5 192 249
2 191 226
Installation and mechanical specifications
Table: FZHI installation and mechanical specifications
Property Value
pole
Installation options
wall
IP rating IP65
Dimensions and weight
Table: FZHI dimensions and weight
Property Value Dimensions orientation
Height 355 mm (13.97 in.)
Depth 203 mm (7.99 in.)
Width 441 mm (17.36 in.)
Weight max. 24 kg (52.91 Ibs)
Environmental specifications
Table: FZHI environmental specifications
Property Value
Maximum operational temperature +55°C (+131°F)
Minimum operational temperature -40°C (-40°F)
LEDs
Table: FZHI LEDs
LED status Description Alarm
RRH - red, stable A critical alarm has occurred or a reset is ongoing (red Critical alarm
stable for max. 5 s, then yellow stable).
RRH - red, blinking A major or minor alarm has occurred. Major or
minor alarm
RRH - yellow, stable Module is on and the status is set to ‘waiting’ or ‘blocked’. No alarm
RRH - yellow, blinking SW download is in progress or configuration is ongoing. No alarm
Module is non-operational at the moment.
RRH - green, stable Module is operational. No alarm
RRH - green, blinking Module is loading software or parameters. No alarm
RRH OPTx port - green, stable SFP link is connected to the System Module or extension No alarm
sub-module.
RRH OPTx port - red, stable SFP is installed, but no fiber or link is present. No alarm
RRH OPTx port - switched off No SFP or SFP power is down. No alarm
RRH TX - green, stable PA power is on. No alarm
RRH TX - green, blinking PA power is off. No alarm
Warnings, cautions or notes related to the product
WARNING! Risk of electric shock.Before turning RF power on, RF ports have to be terminated by
nominal 50Ω load (for example, feeder with antenna). However, if these conditions are not met, the plastic
caps that are delivered within the unused RF ports should remain in place. The plastic caps isolate RF
power from the environment, and thus provide electric shock security in case RF power is accidentally on.
NOTICE: The RRH should always be mounted in a
vertical orientation with connectors on the bottom side
to ensure convection cooling.
Note: The minimum startup voltage is -40.5 V DC. If the input voltage is below/beyond extended limits,
unit might shut down.
