Product Selling Guide
35Z-1 & 36C-1
3.5T Zero & Conventional tail swing
Compact Excavators
500 hr greasing intervals with graphite impregnated bronze bushes on the
entire dig end, kingpost & dozer
Best-in-class tearout
All new instrumentation with a new LCD colour display screen
Programmable high & low flow aux with Tool Select for up to 10
attachments
100% steel bodywork
Product Selling Guide
Why buy a JCB 3.5 Tonne Excavator
• Low Cost of Ownership
- 500hr dig end greasing intervals
- Load-sensing hydraulics only consume power on demand
- Flat glass
- Steel bodywork
- Programmable auto-idle with 8 power bands
• Performance
- New electronically-controlled pump provides exceptional power
and versatility with best-in-class Aux flow
- Best-in-class bucket & dipper tearout
- Auto shift tracking provides superior productivity
• Comfort
- Spacious cab with flat floor
- Joystick operated boom swing
- Bluetooth handsfree radio with USB
• Ease of Use
- All new instrumentation with LCD display
- On board health check information
- Electro hydraulic dozer fine control
- Customisable controls and display
• Safety & Security
- 2GO safety system
- Full control isolation & neutral start
- Live link & immobiliser options
Product Selling Guide
Fast Facts
35Z-1 36C-1
Engine Model EU Stage V / EPA Tier 4 Final Perkins 403J-17
Gross power ISO 14396 (Kw) 18.4 (@ 2200rpm)
A Sprocket idler centres mm 1590
B Track length on ground mm 1590
C Undercarriage overall length mm 2048.5
D Kingpost clearance mm 555
E Tailswing radius mm 900 1300
F Overall width of superstructure mm 1550
G Height over cab mm 2482
H Ground clearance mm 275
I Track gauge mm 1400 1200
J Width over tracks mm 1750 1550
K Transport length with standard dipper mm 4851 4806
L Track height mm 480
M Counterweight clearance mm 563
Product Selling Guide
New features over and above the previous models are:
A new family Compact Excavator appearance - which
represents
strength and purpose
New Display with rotary control dial and membrane
switch panel
Hydraulic quick hitch - Factory ready hydraulic quick
hitch
Roto tilt ready system – A factory ready complete
installation to pick up a variety of attachments
All steel bonnets - Better resistance to on site damage,
easier to repair for less down time
500 hours greasing intervals
Product Selling Guide
Fully integrated tie down points to ease transportation.
EH Dozer lever control for ease of control
Programmable flow settings for optimum attachment
usage.
Electro proportional auxiliary controls
Allows finer control of attachments
New dig end geometry - Allows machine to load
dumpers
without the need to re-position the machine
Auto idle throttle - Returns to idling speed
automatically
reducing fuel consumption, noise and emissions
Follow Me Home Lights aids the operator to leave site
safely
LED lights as standard – 2 front, 1 boom, 1 rear
Exterior cab mirrors as standard – left and right
1300mm dipper as standard on 35Z, 1600mm dipper
as standard on 36C.
Long dipper + additional counterweight available on
35Z – increases overhang by 100mm and weighs 226kg
Product Selling Guide
Walk around – Dig End
35Z-1 36C-1
Dipper length mm 1300 1600
Boom length mm 2450
• 500hr greasing, graphite impregnated bronze bushes on
the entire dig end
• Robot welded boom and dipper made from high tensile
strength steel, with internal baffle plates for long life
durability
• A four-plate dipper design provides added structural
strength. Hoses routed through the top of the dipper for
maximum protection
• High flow double acting aux as standard (70l/min)
• Low flow auxiliary (30l/min) available to suit an array of
hydraulic attachments
Product Selling Guide
Walk around – Dig End
Non Bushed Bushed
• Bushed kingpost
• Optional Hose Burst Check Valves (HBCV) to prevent
the boom & dipper from dropping in the event of a hose
burst
• All hydraulics have O ring face seals (ORFS )
• For protection and lower replacement costs single piece
pipework is fitted and all hoses are armoured
• Quick release auxiliary couplers mounted on the dipper
allow efficient tool change over
• An optional bucket to grab change over valve allows for
versatile use of controls
• Boom worklight guard and heavy duty boom cylinder
guard fitted as standard
Product Selling Guide
Walk around – Dig End
• New 40mm bucket pins accommodate a new range of
ECO buckets for enhanced productivity.
• Pin Diameters: nominal 40 mm
Pin Centres: 190 mm - defines variable centres pick-up range for Hyd
Hitch - QC35-40H1 below
• Dipper Nose (& Bucket Link) Width: 135 mm
(Bucket Jaw Width: 136.9 mm)
• Variable centres Hyd Quick Hitch is capable of picking up:
Pin diameters from: 35 - 40 mm
Pin centres from: 178 - 203 mm (35 mm pins)
185 - 214 mm (40 mm pins)
• 199º bucket rotation for maximum spoil retention
Product Selling Guide
Walk around - Undercarriage
• New “H frame” design provides ultimate strength and
rigidity
• Open design allows material to fall through and sloped
track legs provide easy cleaning and low spoil retention
• Sealed idler tension unit to prevent ingress of dirt
• Bulkhead hose connectors making their replacement
easier and cheaper
• 4 bottom and 1 top roller provides a smooth ride
• Twin speed auto kick down Nachi drive motors
• 8 undercarriage and dozer tie down points for easy
transportation
• New dozer profile and angle provides high performance,
low spoil retention and protected tapered lifting points
• 4 way dozer option for increased productivity when trench
backfilling (must be ordered with High & Low flow aux)
• Dozer float option for quicker grading and ground clean up
Product Selling Guide
Walk around – Undercarriage
Robust 1962mm wide dozer combined
with revised curvature of the blade gives
excellent dozing and material roll
performance but minimises soil retention.
Dozer arms are constructed from robust U
shaped pressings with a closing plate. All
surfaces are angled minimising soil
retention.
Lifting points on the dozer are purposely
angled behind the edge of the blade
providing protection from accidental
damage, plus the geometry aids lifting the
machine.
Pivot pins have pin end greasing and
protected grease nipples
Bulkhead connectors mounted
on the undercarriage frame allow
dozer ram hoses to be easily
changed if accidently damaged -
without having to route them
back to the rotary joint
Twin speed auto kick down Nachi
drive motors automatically adjusts the
speed and power according to the
ground conditions.
Product Selling Guide
Walk around – Undercarriage – Tracks
Depending on application the following tracks can be specified:
• 300mm Bridgestone Pro- Edge rubber tracks (400 x 74 x
72.5) with bespoke tread pattern for ultimate durability
- “Pro-Edge” is the rounded shape at the tip of the
embedded core-metal wing. This reduces stress
concentrations in the edge rubber which typically suffers
edge-cut damage when operators run over kerbs. Pro-
Edge gives a 4-fold improvement over tracks with
conventional shaped core metals.
- The tracks also feature Interlocking core metals – this
increases lateral stiffness and significantly reduces the risk
of de-tracking.
- The bespoke tread pattern has a more gentle impact
on flat surfaces as the track rotates around the idler and
the edge of each individual tread lug contacts the ground
surface
Product Selling Guide
Walk around – Undercarriage – Tracks
• 300mm steel tracks (growsers drilled to allow
bolt on rubber pads to be retrofitted) for arduous
applications
Product Selling Guide
Walk around – Cab/Canopy
• ZTS and CTS share the same cab
• Easy entry, plus high levels of comfort provide a very
desirable work station
• ROP’S & TOP’s certified structure. Optional FOG’s
guard Level 1.
• Flat glass throughout (except for roof screen) minimises
replacement costs.
• Optional JCB Impact Protection glass is fitted to protect
the operator from flying debris.
Product Selling Guide
Walk around – Cab
Product Selling Guide
Walk around - Cab
• New electro-hydraulic dozer lever incorporates tracking
speed button and optional dozer float and 4 way dozer if
specified.
• All controls are ergonomically located on the right-hand
console for ease of use.
• Advanced instrumentation allows the operator to navigate
through various menus.
• Clear floor with foldable tracking pedals maximize leg room
and storage space
• Removable floor mat for easy cleaning
Product Selling Guide
Walk around – Cab New Display
NEW DISPLAY FUNCTIONALITY
• Health Check On First Key On
• Adjustable Seat Presence Switch Timing
• Auto Idle Adjustment
• Intermittent Wiper Speed Adjustment
• Tool Select (Up to 10 Attachments)
• Aux Venting
Product Selling Guide
Walk around - Cab
Display – Home screen
This screen is used by the operator to determine current
machine status and proximity to warning thresholds. The
Top Ribbon will remain present on all screens where as the
main two bottom windows will change when using the
menu. The top ribbon consists of “Machine Hours”,
“Throttle Status” & “Time”.
The main two bottom screens will default to RPM on the
left and Coolant temperature and fuel level on the left.
These two windows will alter as you alter through the
various menu’s and features of the machine.
Symbol
Description Colour
Ref
A SAE Active Green
B Air Filter Blocked Amber
C Seatbelt Red
D Not Used
E Engine Pre-Heat Active Amber
Malfunction Indicator
F Amber
Lamp
G Not Used
H Not Used
Malfunction Indicator
I Red
Lamp
J Swing Green
K Dozer Float Green
L 2 Speed Green
M Active Hydraulics Green
N Not Used
O Battery NOT Charging Red
P Engine Oil Pressure Red
Q Coolant Temperature Red
R Low Fuel Level Red
Product Selling Guide
Navigation Buttons
Return UP
Enter Down
There are four navigation buttons; Return, Enter, Up and
Down. Located on the right hand pod, these are used to
navigate through the display to the various functions and
information.
These buttons are referenced through this guide using
the coloured notations.
Product Selling Guide
Keypad
1. Activate 2. Toggle
Hydraulics Attachme
(LED1 to show nt
Hydraulics
Active)
3. Auto Vent
4. Blank
(This will only
flash when
available)
5. Lift Over load
(LED1 to show Lift Over 6. Auto Idle
load Active, (LED1 to show Auto Idle
LED2 to show Overload) is on,
LED2 to show Auto Idle
7. Work lights is active)
(LED1 to show front work 8. Toggle
light on, Beacon
LED2 to show rear work (LED1 to
light on) show
9. Wiper Mode beacon is
(LED1 to show wiper on on) Quick Hitch
10.
intermittently, (LED1 to show
LED2 to show wiper on quick hitch is
constant, LED1&2 Washers unlocked)
active)
11. Auto Warm
12. Blank
(This will only
flash when
available)
The Keypad will be lit representative of the Spec of
the machine and the options chosen and the
availability to select those features
There are two small red lights just above each icon
which show the status of the feature
The keypad is also used for Immobiliser entry
where the numbers correspond to the pin code,
Tick is used for enter and Return arrow to go back.
Product Selling Guide
Immobiliser
Using the Keypad, enter the 4 digit PIN using the
numerical digits shown on the keypad followed by the
tick for enter. If you make a mistake you can press the
return button to delete the last number pressed.
If the PIN is entered incorrectly 5 times then the
machine will lock itself for 15 Minutes The number of
black squares determines how many tries are left
before lockout. There is a limit of 15 Codes which can
be assigned to the machine. This includes the 1 Master
code
Key code Entry Key code unlock
Key code no. failed Key code lock
attempts out
Key Immobiliser:
If an incorrect key is used, the screen below will be
shown. By using the correct key the machine will
unlock.
There is a limit of 15 Keys in total which can be
assigned to unlock 1 machine. This includes 1 Master
Key (Red)
Product Selling Guide
Health Check
Upon first ignition cycle for the day, the machine Health
Check screen shall be displayed. This screen is designed to
highlight any possible issues with the machine prior to the
machine being worked. It will appear after the key code
has been entered, or the correct immobiliser key has been
used. If there are no issues present, as shown in the
bottom left image the Health check screen shall disappear
after 5 seconds and will return to the home screen. If there
are faults present, then acknowledgement of the fault are
required by pressing the enter button.
Product Selling Guide
Home Screen Navigation
Navigating through the home screen can be done by using
the Up and Down navigation buttons. The home screen
consists off;
- RPM
- Settings
- Machine Information
- Current Attachment
Product Selling Guide
Machine Information
The machine information can be found by pressing the up
and down navigations button till the “i” is found and by
pressing enter.
The machine information will show you various specifics of
the machine and current status. The information that can
be seen is;
- VIN
- Machine software
- Diagnostics
- Temperature
- Fuel consumption
- Hydraulic Pressure
- AUX Flow
- Machine hours/ Hours till service
Product Selling Guide
Adjusting Settings
Press the Enter button when on the settings image will take
you to Level 1 settings menu where you can cycle through
the configurable settings using the Up and Down navigation
buttons. Configurable settings are;
- Time
- Date
- Brightness / Mode
- Units of measure
- Service hours reset
- Seat Presence switch
- Follow me home
- Auto Idle
- AUX latch
- Intermittent Wiper Speed
Product Selling Guide
Adjusting Seat Presence Switch Timing
Adjusting the seat presence switch allows you to change
the time it take to deactivate the hydraulics when the
operator get out of the seat
Toggle up and down buttons to change number of seconds.
3-30 seconds possible in 1 second increments.
Product Selling Guide
Adjusting Auto Idle
Adjusting the Auto idle allows you to define the time to
return the machine to Idle RPM when not in operation.
Toggle up and down buttons to change number of seconds.
2-30 seconds possible in 1 second increments.
Product Selling Guide
Aux Venting
AUX Venting can be complete following a specific process.
1. Put the key in position 1 (Ignition on, but machine not
running)
2. Press the push 2 go button (Button 1)
3. Press AUX 1. When AUX Venting is possible AUX 1
(Button 3) will flash. If AUX venting isn’t possible, the
button won’t flash
4. Press Push 2 Go, this will flash when available.
Product Selling Guide
Aux Hydraulics Tool Select
• Using the navigation buttons on the home screen find the
attachment screen. When shown like the image on the
left, the “Toggle attachment” button, button 2 on the
keypad, can be pressed which will cycle and choose
through the pre set attachments.
• Editing the attachments can be done by pressing “enter”
with the navigations buttons as shown in the next page.
Product Selling Guide
Aux Hydraulics – Editing attachments
Level 0
Level 1
• See over page
Product Selling Guide
Aux Hydraulics – Editing attachments
Press the Enter button when on the Attachments
Menu screen and this will take you to Level 1
Attachments Sub Menu where you can navigate
through Level 1 Attachments Sub Menu using the up
and down arrow buttons. There are a possible of 10
Pre saved attachment
Press the Back button when on any Level 1
Attachments Sub Menu to be returned to the
Attachments Menu
3 Attachments come set up as standard;
Bucket = No AUX,
Hammer = AUX1 single acting Thumb = AUX1
double acting
Please note, Auxiliaries will not work if an attachment
isn’t selected or set up without AUX
Product Selling Guide
Aux Hydraulics Editing attachments
• By pressing enter on any level 1 attachments will bring you
to level 2. On level two you can select what you would
like to edit on the attachment.
• From top to bottom you can edit, Image and toggle
selection, AUX settings and AUX flow
Product Selling Guide
Aux Hydraulics Image & Toggle attachments
Level 2 Level 3 Level 4
• After pressing enter on a level 2 you are taken to level 3
which will allow you to alter the images using the up and
down navigation buttons. All the images are shown on the
left. After pressing enter on the chosen image, you are
given the option to choose between a “tick” or “cross”.
This defines whether it is visible whilst using toggle
attachment.
• By pressing return at any stage during the process will
remove what is selected and return to the level below. To
save the changes press enter at Level 4 which will return
you back to level 2.
Product Selling Guide
Edit attachments AUX settings
Level Level Level
2 3 4
• When enter is pressed on Level 2 AUX you can select the
Auxiliary you want to alter with options AUX 1 to 4
depending on the attachment selected. Pressing enter on
any Level 3 AUX option will take you to level 4 the type of
AUX you want, which the options are dependant on the
Aux chosen. This is shown in the red boxes above.
Product Selling Guide
Edit attachments AUX Flow
• When enter is pressed on Level 2 AUX Flow you can
select the Auxiliary you want to alter with options AUX 1
to 4 depending on the attachment selected. Pressing enter
on any Level 3 AUX option will take you to level 4 the
Flow of AUX you want, which the options are dependant
on the Aux chosen. For double acting Auxiliaries you’ll be
able to alter both side “A” and “B”, for single acting AUX
you’ll be able to alter “B” as shown above.
Product Selling Guide
Throttle – Fuel saving features
To optimise fuel consumption the following features are fitted as
standard:
• Below idle system:
Engine revs automatically drop
below idle when the operator’s
armrest is lifted, this unique
. feature improves fuel economy
and reduces noise levels.
• Programmable auto idle:
Auto idle can be programmed to
activate between 2 and 30
seconds after the controls have
been inactive to increase fuel
efficiency
• One touch idle:
Press down on the centre of the
rotary controller and the rpm
drops to idle. Press again and it
returns to preset rpm. Ideal when
briefly stopping work.
• .
Product Selling Guide
Walk around - Engine
Perkins 403J-17 EU Stage V / EPA Tier 4 Final
- Gross power 18.4 kW
- Can be sold worldwide
Electronically controlled isochronous governing of the
mechanical fuel injection system maintains the speed of the
engine truly constant, regardless of the load.
On start up the throttle controller no longer needs to be
reset to minimum position as the required engine rpm is
automatically achieved depending on the pre-set position of
the rotatory throttle control.
Product Selling Guide
Hydraulics
• Bosch-Rexroth 38cc variable displacement piston pump
mounted on the output shaft of the engine delivers 76
l/min
• Closed centre Bosch-Rexroth valve block provides
improved flow sharing for smooth, precise controlled and
balanced operation during multifunctioning
• All hydraulic hoses are colour coded for quick and easy
hose identification in the event of accidental hose damage
• High flow electro-proportional single auxiliary now fitted
as standard delivering 70l/min (adjustable between 120
and 250 bar), controlled via an electro-proportional
thumb roller on the right-hand joystick. Low flow (double
acting) can be optionally specified delivering 30 l/min
(adjustable between 120 and 250 bar), controlled via an
electro-proportional thumb roller on the left hand
joystick.
• Programmable/adjustable auxiliary flows for total
attachment compatibility and precision control
• Single to double acting change over valve is electronically
controlled by a switch in the cab (unlike the old
mechanical change over tap)
Product Selling Guide
Hydraulics
• The Bosch Rexroth valve block is an industry leading
quality component. Along with the Bosch Rexroth pump
it delivers smooth and fine control to all hydraulic services
plus fuel savings.
• The patented return-line circuit pressure is lowered,
making the system more efficient as the pump does not to
need to overcome as high a pressure, before any work
can be done.
• O ring faces seals are used throughout the hydraulic
system.
Product Selling Guide
Hydraulics
Auto-warm hydraulics
• Auto-warm protects the hydraulic system in cold climates
when the temperature is below -6ºC.
• Auto-warm latches AUX 1 speeding up the warming
procedure.
• The machine ECU automatically recognises when the
hydraulic oil is below working temperature and restricts
certain functions until working temperature is achieved:
• Engine RPM is limited to 'ECO' mode allowing 1800rpm
maximum by use of the throttle control.
• Idle speed is raised dependent on coolant temperature.
• Hydraulic functionality is limited to high flow auxiliary, to
allow safe warm up of the hydraulic system.
• The auto –w arm button flashes when it can be activated
Product Selling Guide
Safety & Security
Neutral start – The left hand pod must be in the raised
position before the engine will start preventing accidental
operation of hydraulic controls
Unique “2Go” safety system fitted as standard requires the
operator to press a secondary acknowledgement switch
before the controls become active. None of the competition
offer this feature. This can be disabled by the dealer if
requested
Full control isolation - all hydraulic services are disabled
including the excavator joysticks, tracking levers, boom swing
and auxiliary controls when the left hand pod is raised for
optimum safety, removing the risk of inadvertent operation of
the machine
Immobiliser – Either a key or keypad immobiliser can be
specified to prevent theft, or unauthorised use of the
machine, plus can lower insurance premiums in certain
territories.
JCB LiveLink as standard collects valuable information about
your JCB machine and delivers it to you to help ensure that:
- Your machine is safe
- Your machine is well maintained and available to work
- Your machine delivers maximum productivity and
efficiency
Product Selling Guide
Applications
Applications vary enormously dependant upon customer
needs, but can include:
• Housebuilding – footings, services, drainage
• Utilities – Gas, water, electric, TV, telephone, street
repairs, street lighting
• Municipality – Street repairs, drainage ditches, water and
sewer repairs
• Roads & highways – embankment & ditch maintenance,
drainage
• Landscaping – irrigation, drainage, sculpting, tree planting &
removal
• Demolition – sorting, removing and loading concrete
• Waste & recycling – sorting, container stuffing & loading
• Forestry – ditching, sorting, fencing
• Agriculture – ditching, trenching, fencing
• Environmental – flood prevention, test holes, removing
contaminated soil
• Rail – track maintenance, clearing vegetation
Product Selling Guide
Options – Dipper & Bucket ram guards
• Guard protects the cylinder rods from falling
objects/collision
Product Selling Guide
Options – Quick hitch ready pipework
• Allows retro- fitment of hydraulic hitch
• Pipework terminates at dipper nose
• Fully integrated system including boom mounted LED
warning light and release button in cab
• High pressure quick hitch valve
Product Selling Guide
Options – Hydraulic Quick Hitch
• Complete installation from the factory including quick
hitch pipework
• Fully integrated system including boom mounted LED
warning light and release button in cab
• High pressure quick hitch valve
• Allows quick change of attachments
Product Selling Guide
Options – Hydraulic Quick Hitch
• The only fully CE marked (factory fitted) quickhitch for
Compact Excavators on the market achieving all current
and future legislation
• Two independent locking mechanisms designed to
ensure the attachment is secure in any scenario
• Spring activated locks and double locking mechanism
ensures the hitch can operate in all environments with
assurance that the locks will stay clamped
• Variable pin centre design allows the machine to pick up
and change a wide range of attachments (178 to
203mm pin centres with 35mm pins and 185mm to
214mm pin centres with 40mm pin diameters)
Product Selling Guide
Options – Bucket to grab changeover
valve
• Hydraulic attachments such as a swinging grapple or kerb
grab (that does not require bucket crowd service) can be
controlled by the right hand joystick (instead of the bucket
service)
• The change-over valve diverts oil from the bucket cylinder to
the auxiliary line
Product Selling Guide
Options – Tilt Rotate Ready
• Tilt Rotate ready hydraulics
• Operated from normal JCB joysticks
• Note Tilt rotate unit is not supplied by JCB
Product Selling Guide
Options - Green seatbelt beacon
• Green beacon flashes when the seat belt is engaged
• Site foreman knows if the seatbelt is engaged
Product Selling Guide
NOTES
9999/???? UK 07/13 Issue ?
