Scribd
Upload
70 views7 pages

Instrument Panel

This document provides instructions for removing an instrument panel from a vehicle in 21 steps. It begins by disconnecting the battery, removing the steering wheel and covers. Subsequent steps remove various interior trim pieces, registers, the combination meter, radio and heater controls to fully expose the instrument panel. Step 20 describes removing the instrument panel by removing 4 bolts and disconnecting connectors, noting the panel has a clip that requires being pulled at an angle. Reinstallation follows the removal steps in reverse order.

Uploaded by

indrajith.me
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
70 views7 pages

Instrument Panel

This document provides instructions for removing an instrument panel from a vehicle in 21 steps. It begins by disconnecting the battery, removing the steering wheel and covers. Subsequent steps remove various interior trim pieces, registers, the combination meter, radio and heater controls to fully expose the instrument panel. Step 20 describes removing the instrument panel by removing 4 bolts and disconnecting connectors, noting the panel has a clip that requires being pulled at an angle. Reinstallation follows the removal steps in reverse order.

Uploaded by

indrajith.me
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 7

BO−39

BODY − INSTRUMENT PANEL

INSTRUMENT PANEL
COMPONENTS
BO−40
BODY − INSTRUMENT PANEL

COMPONENTS (Cont’d)
BO−41
BODY − INSTRUMENT PANEL

INSTRUMENT PANEL REMOVAL


1. DISCONNECT BATTERY CABLE FROM NEGATIVE (−)
TERMINAL
2. REMOVE STEERING WHEEL
(See page SR−5)
3. REMOVE STEERING COLUMN COVERS
4. REMOVE ENGINE HOOD RELEASE LEVER
Remove 2 screws and the engine hood release lever.
5. REMOVE COWL SIDE TRIM
Remove the nut and the cowl side trim.
6. REMOVE INSTRUMENT LOWER CENTER COVER
Remove 2 clips and the cover.
7. REMOVE KEY CYLINDER COVER
Pry out the key cylinder cover.

8. REMOVE LOWER FINISH NO. 1 PANEL


(a) Remove 4 screws, the bolt and the panel.
(b) Disconnect the connector.
9. REMOVE DUCT HEATER TO REGISTER NO.2

10. REMOVE KNEE PANEL


Remove 3 bolts and the cover.

11. REMOVE HEATER CONTROL PLATE


(a) Pull off the heater control knobs.
(b) (w/ A/C)
Pry off the A/C switch.
(c) Using a screwdriver, pry out the heater control plate, as
shown in the illustration and remove it.
HINT: Tape the screwdriver tip before use.
BO−42
BODY − INSTRUMENT PANEL

12. (Models Ex. 4−Speed M/T)


REMOVE CLUSTER FINISH PANEL
(a) Remove 3 screws and pull out the cluster finish panel.
(b) Disconnect the connectors.
(c) Remove 2 screws and the cup holder from the cluster finish
panel.

13. (4−Speed M/T Models)


REMOVE CLUSTER FINISH PANEL WITH METER HOOD
(a) Remove 2 screws and pull out the cluster finish panel with
meter hood.
(b) Disconnect the connectors.
(c) Pull off the meter hood.
(d) Remove 2 screws and the cup holder from the cluster finish
panel.

14. REMOVE INSTRUMENT PANEL NO. 1 REGISTER


Remove 2 screws and the register.
15. REMOVE COMBINATION METER
(a) Remove 4 screws.
(b) Disconnect the connectors.
(c) Remove the combination meter.

16. REMOVE LOWER FINISH NO. 2 PANEL WITH GLOVE


COMPARTMENT DOOR
(a) Remove 4 screws, the bolt and the lower finish No. 2 panel
with glove compartment door.
(b) Disconnect the connector.

17. REMOVE LOWER CENTER FINISH PANEL


(a) Remove a screw and pull out the panel.
(b) Disconnect the connectors.
BO−43
BODY − INSTRUMENT PANEL

18. REMOVE HEATER CONTROL


Remove 2 screws and hang the heater control.
19. REMOVE RADIO
(a) Remove 4 bolts.
(b) Disconnect the antenna cable and connectors.
(c) Remove the radio with bracket.

20. REMOVE INSTRUMENT PANEL


(a) Remove 4 bolts and the instrument panel.
(b) Disconnect the connectors.
HINT: The instrument panel has a boss onto the clip on the
body side. Therefore when removing, pull upward at an
angle.
BO−44
BODY − INSTRUMENT PANEL

21. REMOVE FOLLOWING PARTS FROM INSTRUMENT


PANEL
(Models Ex. 4−Speed M/T)
(a) Safety pad.
(b) No. 3, No. 5 heater to register ducts.
(c) Instrument panel No. 2 register.
(d) Center bracket.
(e) Cowl bracket.
BO−45
BODY − INSTRUMENT PANEL

(4−Speed M/T Models)


(a) No. 3, No. 5 heater to register duct
(b) Instrument panel No. 2 register
(c) No. 2, No. 3 instrument panel
(d) Mounting bracket
(e) Cowl bracket

INSTRUMENT PANEL INSTALLATION


(See page BO−39 and 40)
INSTALL INSTRUMENT PANEL PARTS FOLLOWING RE-
MOVAL SEQUENCE IN REVERSE

You might also like