COPYRIGHT 2013

Unlocking Technology

Nissan - Infiniti
(Version 4.2)

World Leader s In Automotive Key Progr ammi ng Equipment

w w w . a d v a n c e d - d i a g n o s t i c s . c o m
™

1 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

CONTENTS

PAGE

APPLICATIONS 3

DIAGNOSTIC SOCKETS/OBD PORTS

NISSAN / INFINITI 4-5

GENERAL OPERATION 6 -7

SPECIAL FUNCTIONS 8 - 25

TIPS & HINTS 26

REMOTE CONTROL PROGRAMMING 27 - 29

2 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

APPLICATIONS Have Moved to IQ - Online

Applications are continually updated as vehicles are constantly added.

To ensure you have the very latest information,
the applications list is available via Info Quest - an online portal
containing vehicle technical data for key & remote programming
for all manufacturers.
To view the latest vehicle applications please visit
Info Quest at
http://iq.advanced-diagnostics.co.uk/

Nissan - Infiniti Software

ADS112 Nissan - Infiniti

ADS159 Nissan - Infiniti CAN & PROX

ADS169 Nissan - Infiniti 2009

ADS197 Nissan - Infiniti 2013 PROX

3 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

DIAGNOSTIC SOCKETS/PORTS

NISSAN
MICRA PRIMERA

PRIMERA 2002 SERENA

ALMERA CUBE

NEW MICRA SKYLINE

WINGROAD BLUEBIRD

MICRA 14 PIN PRIMERA K12

4 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

DIAGNOSTIC SOCKETS/PORTS

NISSAN
TERRANO 14 PIN MURANO

MAXIMA TIIDA

PIXO XTRAIL (T31)

NAVARA (D40) XTRAIL (T30)

PATHFINDER (R51) BLUEBIRD SYLPHY

PATROL (Y51) JUKE

5 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

GENERAL OPERATION

INTRODUCTION
The Nissan Anti Theft System (NATS) was introduced initially around 1995 with a basic
immobiliser, which did not use key transponders. This system was known as NATS 1.
Subsequently NATS 2 was introduced which uses the transponder technology.

Further iterations of the NATS system have been introduced, up to NATS 6.5. The earlier systems use a security timed ac-
cess, similar to Ford systems, which require a period of time before the keys can be programmed.

NATS 5 uses a pin code, as with GM and VAG systems. This system was fitted on vehicles from 2001 MY onwards.

A further development is the introduction of a CAN system that was first introduced on the Micra in 2003. The Micra system
comes in two forms either the Intelligent System or
Non-Intelligent system.

NATS IGNITION KEY

This uses standard transponder technology, and have both RED and BLUE chips to
identify non crypto and crypto type transponders. The BLUE chip types are fitted on the
latest NATS 5 system.

When programming keys, on NATS systems up to NATS 4, all keys stored in memory will be deleted, however on NATS 5
additional keys can be added. Up to 5 keys can be programmed into NATS 5 systems, and 4 keys into NATS 2,3 & 4 sys-
tems.

NATS IMMOBILISER UNIT

The NATS immobiliser unit, is normally mounted next to the ignition switch or behind the fascia area. The unit is some-
times also fitted with a dongle unit, and is fitted on right hand drive European vehicles for extra security.

The NATS immobiliser controls signals to the Engine Control Module (ECM) which inhibit starting.

On later systems there is also an input from the Audio system, which if disconnected
inhibits the starting of the vehicle.

On CAN systems the immobiliser function is part of the Body Control Module (BCM), which controls signals to the Engine
Control Module (ECM) which inhibit starting.

NATS SECURITY INDICATOR

The security LED is normally mounted in the dashboard area and indicates the status of the system.

When a problem is detected, the LED will indicate the fault as listed in the following
table when the IGN is ON or in accessory position.

CAN SYSTEMS

NON-INTELLIGENT SYSTEM
This system uses a key with a combined remote control in the key head.

INTELLIGENT SYSTEM
The intelligent system uses a key fob that has a folding key blade that can be used in emergencies.

This system works by proximity detection i.e. when the driver is within a few feet of the vehicle the door automatically un-
locks. To start the vehicle the driver depresses the brake pedal and turns the butterfly ignition without putting the key in
the ignition. In emergency situations the key blade

6 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

GENERAL OPERATION

CONDITION WITH DONGLE WITHOUT DONGLE

ENGINE
ENGINE CHECK
CHECK NATS LED NATS LED
LIGHT
LIGHT

6FLASHES& ON AF-
NATS FAULT (NO DONGLE
TER IGN IS LED ON
FAULT)
SWITCHED ON

REMAINS ON FOR 15
NATS FAULT (DONGLE FAULT) MINUTES AFTER IGN
IS SWITCHED ON

6FLASHES &
NATS FAULT AND ENGINE COM-
LED ON ON AFTER IGN IS LED ON LED ON
PONENT FAULT
SWITCHED ON

ENGINE FAULT LED ON LED ON

AFTER NATS PROGRAMMING 6 FLASHES

IMMU ECM received a signal from IMMU, indicating that IMMU is malfunctioning.

ECM Control unit is faulty

CHAIN OF ECM-IMMU Communication between ECM and IMMU

DIFFERENCE OF KEY IMMU can receive the Key ID signal but ID

verification between Key ID and IMMU is incorrect.

CHAIN OF IMMU KEY IMMU cannot receive key ID & Dongle unit is malfunctioning (IF FITTED)

ID DISCORD, IMM-ECM The result of ID verification between IMMU and ECM is no good. System pro-
gramming is required.

ELECTRONIC NOISE Electronic interference in NATS communication lines during communication.

DON’T ERASE BEFORE Engine trouble code from Engine diagnostics

CHECKING ENG DIAG detected.

LOCK MODE When the starting operation is carried out 5 or more times consecutively, if an
unregistered key is used or ECM or IMMU is faulty then the NATS system shifts
to mode 1 to stop engine from starting.

ECM INT CIRC-IMMU The malfunction of ECM internal circuit of IMMU

communication line is detected.

7 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 2,3 & 4 SYSTEMS

PROGRAM KEYS PROGRAM KEYS

VEHICLE SELECTION ECU IDENTIFICATION

+ LANCIA
+ MITSUBISHI NATS 2 PETROL
+ NISSAN
+ PEUGEOT

+ ROVER
+ SUZUKI PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

AUS ECU IDENTIFICATION

EURO FAULT CODES

USA SPECIAL FUNCTIONS

PINCODE CONVERTOR

PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

+ INTERSTAR PROGRAM KEYS

+ PRIMASTAR
+ MAXIMA
+ MICRA

+ NAVARA
+ PATROL PRESS ENTER KEY

VEHICLE SELECTION PROGRAMMING KEYS

-> 2000

00 -> 03 . . . . . . . . . PLEASE WAIT

+ 03 ->

KEYS PROGRAMMED

PROCEDURE COMPLETE
SWITCH IGNITION ON CYCLE IN ADDITIONAL

KEYS NOW IF REQUIRED

DISCONNECT TESTER
FROM VEHICLE
PRESS ENTER KEY PRESS ENTER KEY

NOTE : FOR ALL ADDITIONAL

KEYS CYCLE IN EACH KEY
NOTE : THE IGNITION MUST NOW.
ALREADY BE ON AT THIS STAGE,
AS THE CONNECTION TO NATS 2
SYSTEMS CAN ONLY BE MADE WHEN YOU TRY TO START
WHEN IGNITION IS ON. THE VEHICLE THE SYSTEM
THEN CLOSES AND NO MORE
KEYS CAN BE ADDED.

8 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 5 SYSTEMS
PROGRAM KEYS PROGRAM KEYS PROGRAM KEYS

VEHICLE SELECTION ECU IDENTIFICATION

NOTE : AT THIS POINT CYCLE
+ LANCIA IN ALL KEYS THAT ARE
+ MITSUBISHI NATS 5 REQUIRED TO BE
PROGRAMMED.
+ NISSAN
+ PEUGEOT DO NOT START THE VEHICLE
AS THIS CLOSES THE
+ ROVER
PROGRAMMING CYCLE.
+ SUZUKI PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

AUS ECU IDENTIFICATION

EURO FAULT CODES

USA SPECIAL FUNCTIONS

PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

NISSAN SYSTEMS PROGRAM KEYS

ALMERA

ALMERA TINO
CABSTAR
INTERSTAR

PRIMASTAR PRESS ENTER KEY

VEHICLE SELECTION SECUIRTY CODE

PETROL
____
DIESEL

1 2 3 4 5
6 7 8 9 0
VEHICLE SELECTION SECUIRTY CODE
> 2000
1234
2000 >

 
KEY PROGRAMMED
SWITCH IGNITION ON CYCLE IN ADDITIONAL
KEYS

PRESS ENTER KEY PRESS ENTER KEY

9 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 5 SIEMENS PIN CODE

PINCODE CONVERTOR PINCODE CONVERTOR

VEHICLE SELECTION PLEASE ENTER DATE CODE

+ LANCIA
____
+ MITSUBISHI
+ NISSAN
+ PEUGEOT
1 2 3 4 5
+ ROVER
+ SUZUKI 6 7 8 9 0

VEHICLE SELECTION PLEASE ENTER DATE CODE

EURO
1234
AUS
USA
PINCODE CONVERTOR

 
VEHICLE SELECTION PLEASE ENTER PIN CODE
SIEMENS
____
SUPERCODE
SUPERCODE LABELS

1 2 3 4 5
6 7 8 9 0
PLEASE ENTER PIN CODE

1234
PINCODE CONVERTOR

PRESS ENTER KEY  

NISSAN PIN CODE NISSAN PIN CODE

PLEASE REFER TO THE MANUAL MADE IN MEXICO : 5E83

TO IDENTIY THE DATE CODE MADE IN GERMANY : 4343
AND THE PIN CODE FROM THE MADE IN EUROPE : 4343
IMMOBILISER LABEL

PRESS ENTER KEY

NOTE : ON SOME MODELS YOU

WILL GET LETTERS IN THE PIN
CODE, IGNORE THESE AND USE
NOTE : PLEASE SEE LABEL GUIDE THE PIN CODE THAT HAVE
FOR DATE CODES AND PIN CODES NUMBERS ONLY.
ON THE FOLLOWING PAGE.
IF THERE ARE MORE THAN 1 PIN
CODE THEN TRY EACH ONE IN
TURN TO FIND CORRECT PIN.

10 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 5 SIEMENS PIN CODE

RED NUMBER = DATE CODE

NOTE : IGNORE THE LAST 2 DIGITS, JUST INSERT THE

FIRST 4 DIGITS INTO THE AD KEY PROGRAMMER.

GREEN NUMBER = ENCRYPTED PIN CODE

RED NUMBER = DATE CODE

GREN NUMBER = ENCRYPTED PIN CODE

11 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 5 SUPERCODE(ADC176)
2004 to 2009 Vehicles
PINCODE CONVERTOR PINCODE CONVERTOR
CONVERT 2004 - 2009 NISSAN / INFINITI
VEHICLE SELECTION NISSAN PIN CODE BCM LABEL NUMBERS TO 4 DIGIT PIN
CODES.
+ LANCIA
+ MITSUBISHI INITIALISING DONGLE NOTE:ADS198 ALSO CONVERTS 2009>
VEHICLES
+ NISSAN
+ PEUGEOT FOR USE WITH MVPPro & TCODEPro.

+ ROVER SMARTCARD ENABLED TESTERS ONLY.

+ SUZUKI PRESS ENTER KEY

VEHICLE SELECTION NISSAN SUPERCODE

EURO _____
AUS
USA
PINCODE CONVERTOR 1 2 3 4 5
6 7 8 9 0

VEHICLE SELECTION PLEASE ENTER DATE CODE

SIEMENS
A1234
SUPERCODE

SUPERCODE LABELS

 
NISSAN PIN CODE

PINCODE CONVERTOR PINCODE: 1234

PLEASE TURN OFF TESTER

PRESS ENTER KEY

NISSAN PIN CODE

PLEASE ENSURE THAT

NOTE :
THE NISSAN SUPERCODE
DONGLE IS FITTED

ADC176 HAS NOW

AND THE TESTER IS
POWERED FROM THE VEHICLE

PRESS ENTER KEY

BEEN
NOTE : THE NISSAN SUPERCODE
DONGLE ONLY WORKS WHEN YOU
SUPERSEDED
ARE CONNECTED TO THE VEHICLE
POWER. BY ADC198
IT WILL NOT WORK CONNECTED
THROUGH THE POWER
CONNECTOR !

12 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—2009 > Pin Codes

In 2009 Nissan changed the pin code system on ALL models across the world.

The Nissan SUPERCODE (ADC176) or the SIEMENS converter (ADS170|) will not work on this new system.

The way to identify if the vehicles that use this new system is to check the label on the BCM, if it has the
manufacturer name CONTINENTAL then this uses the new pin code system.

These pin codes can be obtained as follows :-

1. Pin code can be obtained by using DONGLE ADC198

2. Advanced Diagnostics Pin code service, using PAYPAL as payment (24 hours service)
3. Direct from a Nissan dealer.
4. NASTF system in the USA.

A couple of examples of a BCM are shown....

13 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN/ INFINITI BCM TO PIN CODE CONVERSION (ADC198)

CONVERT 2004 - 2012 NISSAN / INFINITI BCM LABEL NUMBERS TO 4 DIGIT PIN
PINCODE CONVERTOR CODES. FOR USE WITH MVPPro & TCODEPro.
SMARTCARD ENABLED TESTERS ONLY.

VEHICLE SELECTION NISSAN BCM CODE

+ LANCIA
_____ NEXT STEP: WRITE
+ MITSUBISHI DOWN PINCODES
+ NISSAN THEN TURN OFF THE
+ PEUGEOT
1 2 3 4 5 PRO AND REMOVE THE
+ ROVER ADC198 DONGLE
+ SUZUKI 6 7 8 9 0
VEHICLE SELECTION NISSAN BCM CODE
TROUBLESHOOTING
EURO
BCM 123AF MAKE SURE THE PRO IS BEING
AUS
POWERED BY A VEHICLE USING THE
USA STANDARD CABLE.

PINCODE CONVERTOR ADC198 WILL NOT WORK OFF THE

  WALL ADAPTOR OR THE CIGARETTE

ADAPTOR

VEHICLE SELECTION NISSAN ADC198

SIEMENS
ADC176 > 2009 BCM: 123AF

ADC176 >2009 LBLS PINCODE > 2009 :5940

ADC198 - 2009 > PINCODE 2009 > 0792

PLEASE TURN OFF TESTER

PINCODE CONVERTOR

PRESS ENTER KEY

NISSAN PIN CODE

PLEASE ENSURE THAT

THE NISSAN ADC198 DONGLE IS
FITTED AND THE TESTER IS
POWERED FROM THE VEHICLE

PRESS ENTER KEY

NISSAN PIN CODE

INITIALISING DONGLE THIS PROCEDURE DOES NOT

USE A TOKEN ON THE
PLEASE WAIT

MVPPRO
PRESS ENTER KEY

14 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 5 BCM LABELS (ADC176 & ADS198)

NOTE : USE BCM

READ FUNCTION ON
PRO SOFTWARE TO
READ BCM CODE ON
THIS TYPE.

15 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 5 BCM LABELS (ADC176 & ADS198)

16 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 6.5 NOTE/K12 SYSTEM

PROGRAM KEYS PROGRAM KEYS PROGRAM KEYS
SECURITY CODE
VEHICLE SELECTION ECU IDENTIFICATION
+ LANCIA ____________
+ MITSUBISHI ECU NO. AX602
+ NISSAN
+ PEUGEOT 1 2 3 4 5
+ ROVER
+ SUZUKI PRESS ENTER KEY 6 7 8 9 0

VEHICLE SELECTION DIAGNOSTIC MENU SECUIRTY CODE

AUS ECU IDENTIFICATION
123A56B8901F
EURO SPECIAL FUNCTIONS

USA

PRESS ENTER KEY  

VEHICLE SELECTION DIAGNOSTIC MENU PROGRAM KEYS

NISSAN SYSTEMS PROGRAM KEYS

MAXIMA KEYS PROGRAMMED SWITCH IGNITION ON
MICRA PROGRAM REMOTE
NAVARRA ERASE REMOTES
NOTE CHECK REMOTES
PRIMASTAR PRESS ENTER KEY PRESS ENTER KEY

VEHICLE SELECTION

NORMAL SWITCH IGNITION OFF NOTE : ENSURE YOU START

INTELLIGENT REMOVE KEY WITH AN UNPROGRAMMED
KEY IN THE IGNITION,
OTHERWISE AN ERROR WILL
OCCUR.

PRESS ENTER KEY

PINCODE SOURCE PROGRAM KEYS

1.DEALER CODE
IS THE SECURITY LED
NOTE : IF NO 2. ADVANCED
ON OR FLASHING
COMMUNICATION IS DIAGNOSTICS
RECEIVED, SWITCH ON THE
HAZARD WARNING LIGHTS 1 2 3 4 5
WHILE PROGRAMMING.

6 7 8 9 0  
NOTE : THE DEALER CODE IS
WHAT HAS BEEN OBTAINED
IGNITION OFF FROM THE DEALER. PLEASE WAIT

THE AD CODE IS FOR FUTURE

PIN CODE READING ...........
SOFTWARE.

PRESS ENTER KEY

17 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS 6.5 NOTE/K12 SYSTEM

PROGRAM KEYS PROGRAM KEYS

PROGRAM KEYS PROGRAM KEYS

SWITCH IGNITION OFF SWITCH IGNITION OFF

PRESS ENTER KEY PRESS ENTER KEY

PLEASE WAIT PLEASE WAIT

........... ...........

PROGRAM KEYS PROGRAM KEYS

DO YOU WANT TO
REMOVE KEY
PROGRAM MORE KEYS

  PRESS ENTER KEY

PROGRAM KEYS PROGRAM KEYS

REMOVE KEY INSERT KEY

INSERT NEXT KEY AND CYCLE IGN.

PRESS ENTER KEY PRESS ENTER KEY

PROGRAM KEYS

SWITCH IGNITION ON PROCEDURE COMPLETE

PRESS ENTER KEY PRESS ENTER KEY

PROGRAM KEYS
NOTE : AFTER PROGRAMMING
CHECK EACH KEY.
IS THE SECURITY LED
ON OR FLASHING CHECK THE KEY LIGHT
CHANGES FROM RED TO
GREEN AND FLASHES FOR 20

 
SECONDS AND THEN GOES
OUT FOR EACH KEY.

18 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

PIN READ for NISSAN NOTE/K12 NORMAL

PIN READ PIN READ
VEHICLE SELECTION DIAGNOSTIC MENU

+ MERCEDES ECU IDENTIFICATION

+ MITSUBISHI > SPECIAL FUNCTIONS

+ NISSAN
+ PERODUA

+ PEUGEOT
+ PLYMOUTH PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

+ ASIA > READ PINCODE
+ AUS
+ EURO
+ USA

+ PINCODE CONVERTOR

PRESS ENTER KEY

VEHICLE SELECTION PINCODE

TERRANO I
+ TERRANO II 55 B7 AB F3 9E 7C
+ TIIDA
+ VANETTE
+ X—TRAIL
+ READ PINCODE PRESS ENTER KEY

VEHICLE SELECTION

INTERSTAR
PRIMASTAR
+ MICRA
NOTE

HAZARDS ON / IGNITION OFF

PRESS ENTER KEY

ECU IDENTIFICATION

ECU No. : 52All

KEY # 1: 0C 61 83 24

KEY # 2: F1 3D 83 24
KEY # 3: EMPTY

KEY # 4: EMPTY
PRESS ENTER KEY

19 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS PROXIMITY (STEP 1)

READ BCM READ BCM READ BCM

VEHICLE SELECTION VEHICLE SELECTION

NOTE : USE THE NISSAN
+ LANCIA NATS 5 < CAN > PROX SUPERCODE ADC176 TO
+ MITSUBISHI CONVERT BCM -> PIN CONVERT THIS NUMBER TO
THE 4 DIGIT PINCODE
+ NISSAN
+ PEUGEOT SEE NEXT PAGE FOR
+ ROVER
PROCEDURE

+ SUZUKI

VEHICLE SELECTION
AUS
EURO HAZARDS ON / IGNITION OFF
USA

PRESS ENTER KEY

VEHICLE SELECTION
ECU IDENTIFICATION
+ PRIMERA
+ PRIMASTAR
NATS I— KEY
+ PULSAR
+ QASHQAI

+ SERENA
+ SKYLINE
PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

+ J10 ECU IDENTIFICATION
>SPECIAL FUNCTIONS

PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

+ PETROL > # 1. BCM READ
+ DIESEL # 2. STEERING RELEASE
# 3. REGISTER E KEY

# 4. ERASE RKE FUNCTIONS

# 5. PROGRAM RKE FUNCTIONS

VEHICLE SELECTION BCM SERIAL NUMBER

+ MECHANICAL — KEY
+ I— KEY 0A461

PRESS ENTER KEY

20 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS PROXIMITY (STEP 2)

PINCODE CONVERTOR PINCODE CONVERTOR

VEHICLE SELECTION NISSAN PIN CODE

+ LANCIA
+ MITSUBISHI INITIALISING DONGLE
+ NISSAN
+ PEUGEOT

+ ROVER
+ SUZUKI PRESS ENTER KEY

VEHICLE SELECTION NISSAN SUPERCODE

EURO _____
AUS
USA
PINCODE CONVERTOR 1 2 3 4 5
6 7 8 9 0

VEHICLE SELECTION PLEASE ENTER DATE CODE

SIEMENS
A1234
SUPERCODE

SUPERCODE LABELS

 
NISSAN PIN CODE

PINCODE CONVERTOR PINCODE: 1234

PLEASE TURN OFF TESTER

PRESS ENTER KEY

NISSAN PIN CODE

PLEASE ENSURE THAT

THE NISSAN SUPERCODE

DONGLE IS FITTED
AND THE TESTER IS
POWERED FROM THE VEHICLE

PRESS ENTER KEY

NOTE : THE NISSAN SUPERCODE

DONGLE ONLY WORKS WHEN YOU
ARE CONNECTED TO THE VEHICLE
POWER.

IT WILL NOT WORK CONNECTED

THROUGH THE POWER
CONNECTOR !

21 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS PROXIMITY (STEP 3)

STEERING RELEASE STEERING RELEASE STEERING RELEASE

VEHICLE SELECTION STEER LOCK RELEASE

+ LANCIA
+ MITSUBISHI HAZARDS ON / IGNITION OFF SUCCESS
+ NISSAN
+ PEUGEOT

+ ROVER
+ SUZUKI PRESS ENTER KEY PRESS ENTER KEY

VEHICLE SELECTION ECU IDENTIFICATION

EURO
AUS NATS I— KEY
USA
PINCODE CONVERTOR

PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

+ J10 ECU IDENTIFICATION

>SPECIAL FUNCTIONS

PRESS ENTER KEY

VEHICLE SELECTION DIAGNOSTIC MENU

+ PETROL > # 1. BCM READ
+ DIESEL # 2. STEERING RELEASE

# 3. REGISTER E KEY
# 4. ERASE RKE FUNCTIONS

# 5. PROGRAM RKE FUNCTIONS

VEHICLE SELECTION SECURITY CODE

+ MECHANICAL — KEY ____

+ I— KEY

1 2 3 4 5
6 7 8 9 0
VEHICLE SELECTION SECUIRTY CODE
NATS 5 < CAN > PROX
1234
CONVERT BCM -> PIN

 
22 Version 4.2 MAY 2013 Copyright 2013
 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN—NATS PROXIMITY (STEP 4)

REGISTER INTELLI KEY REGISTER INTELLI KEY

DIAGNOSTIC MENU PROGRAM KEY

# 1. BCM READ

# 2. STEERING RELEASE SWITCH IGNITION OFF

> # 3. REGISTER E KEY REMOVE KEY
# 4. ERASE RKE FUNCTIONS

# 5. PROGRAM RKE FUNCTIONS

PRESS ENTER KEY

PROGRAM KEY
NOTE KEY INSERTED INSERT KEY: # 1
IS KEY # 1 SWITCH IGNITION ON
MAX. 4 KEYS ALLOWED
SWITCH IGNITION ON SECURITY INDICATOR
SHOULD FLASH 5 TIMES
PRESS ENTER KEY PRESS ENTER KEY

SECURITY CODE PROGRAM KEY

1234 CHECK ENGINE STARTS

THEN PROCEED TO
IS THIS CORRECT? NEXT STEP

YES=ENTER NO=BACK PRESS ENTER KEY

PROGRAM KEY DIAGNOSTIC MENU

# 1. BCM READ
SWITCH IGNITION OFF # 2. STEERING RELEASE
REMOVE KEY # 3. REGISTER E KEY
# 4. ERASE RKE FUNCTIONS
> # 5. PROGRAM RKE FUNCTIONS
PRESS ENTER KEY

PROGRAM KEYS PROGRAM RKE

DO YOU WANT TO CHECK ENGINE STARTS

PROGRAM MORE KEYS? THEN PROCEED TO

NEXT STEP

YES=ENTER NO=BACK PRESS ENTER KEY

PROGRAM KEY
INSERT KEY: # 1

SWITCH IGNITION ON

SECURITY INDICATOR
SHOULD FLASH 5 TIMES
PRESS ENTER KEY

23 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN / INFINITI 2013 (ADS197)

FIRST STEP - GET 20 DIGIT OUTCODE FROM CAR FOURTH STEP - PROGRAM PROX

VEHICLE SELECTION WARNING PROGRAM PROX

+ LANCIA WARNING: DO NOT PRESS THE

ALL KEYS WILL BE ERASED BRAKE PEDAL.
+ MITSUBISHI DO YOU WANT TO
CONTINUE PRESS AND HOLD THE START / STOP
+ NISSAN
BUTTON UNTIL THE IGNITION
+ PEUGEOT

+ ROVER
+ SUZUKI
  SWITCHES ON

PRESS ENTER KEY

VEHICLE SELECTION IMMOBILIZER RESET REQUEST

RELEASE THE BUTTON ONCE THE
AUS A064– C456-A235-4555-FFC3 DASHBOARD LIGHTS UP AND THE
LIGHT ON THE BUTTON
EURO 20 DIGIT OUTCODE
ILLUMINATES. THIS SHOULD TAKE
USA USE TO OBTAIN IN-CODE FROM A FEW SECONDS.

PIN CODE CONVERTOR NASTF OR DEALER ONCE IT TURNS ON - DO NOT

SWITCH IT OFF UNTIL THE PRO
INSTRUCTS YOU TO.
PRESS ENTER KEY

VEHICLE SELECTION
IMPORTANT: PROGRAM PROX
TYPE 9 ONCE YOU HAVE OBTAINED THE
OUT-CODE FROM THE CAR DO
TYPE 10 NOT DISCONNECT THE TESTER.
TYPE 11
IF YOU HAVE TO START OVER THE PLEASE WAIT
TYPE 12 OUTCODE WILL CHANGE TO A
*************
NEW OUTCODE. THEREFORE IT IS
TYPE 13
ABSOLUTELY NECESSARY TO
NISSAN 2009 STAY CONNECTED UNTIL THE
OUTCODE CAN BE OBTAINED.

PROGRAM PROX

SECOND STEP
HAZZARDS ON / IGNITION OFF
GET INCODE FROM NISSAN
PRESS START / STOP

BUTTON TO SWITCH IGNITION OFF

THIRD STEP
PRESS ENTER KEY
STEERING LOCK RELEASE
PRESS ENTER KEY

ECU IDENTIFICATION ENTER INCODE PROGRAM PROX

PRESS START / STOP BUTTON WITH

A066B455C222EEC4 THE LOGO END OF THE 1ST PROX
PART Number 3TAO Cad
1ST PROX

THE DASH SHOULD LIGHT UP & THE

1 2 3 4 5 SECURITY LIGHT SHOULD BLINK 5
TIMES
PRESS ENTER KEY 6 7 8 9 0 PRESS ENTER KEY

DIAGNOSTIC MENU PROGRAM PROX

ENTER INCODE
ECU IDENTIFICATION
>SPECIAL FUNCTIONS
A066B455C222EEC4
PRESS START / STOP

BUTTON TO SWITCH IGNITION OFF

PRESS ENTER KEY   PRESS ENTER KEY

24 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

SPECIAL FUNCTIONS

NISSAN / INFINITI 2013 (ADS197)

PROGRAM PROX CONTINUED
THE DASHBOARD SHOULD NOW
DISPLAY A MESSAGE THAT READS:
PROGRAM PROX
KEY REGISTRATION COMPLETE

PLEASE WAIT

Notes & Tips

*************

 Always program the PROX part of the key first.

 When entering OUTCODE onto the NASTF site, do

DO YOU WANT TO PROGRAM so using all CAPS.
MORE KEYS?
 Ensure to use the PROX key to push in the Start /
Stop button.

 
 When pressing the Prox key into the Start / Stop
button - make sure that the security light blinks 5
times for each key as it is accepted. If this doesn’t
happen there is a problem.

PRESS THE X ON THE  OUTCODE ERROR MESSAGE ON TESTER : Please

disconnect TESTER AND THE BATTERY for 5min
SCREEN
and then retry procedure.

Obtaining Incodes /
UP TO 4 TOTAL KEYS Pincodes
CAN BE PROGRAMMED.
FOLLOW THE PROMPTS
ON THE PRO. There are several ways to obtain the
necessary INCODE for programming on this
system.

1. If you have a valid N.A.S.T.F Locksmith ID.

Go to http://www.nissan-techinfo.com
PROGRAM PROX
Once you are registered (which by the way, takes some
PRESS THE BRAKE PEDAL time)

& HOLD THE PROX UP TO THE Nissan / Infiniti offer several PAID options to help
START / STOP BUTTON . registered NASTF participants to obtain security codes.
PRESS THE START / STOP BUTTON
ONCE & THE CAR SHOULD START If you do not have a NASTF ID go to www.nastf.org to
learn more about NASTF and about becoming a
participant.
PRESS ENTER KEY
If you have a friendly dealer connection, you may be
able to get help with obtaining the necessary INCODE
from them. However keep in mind that you must be
PROGRAM PROX connected to the vehicle. The INCODE / OUTCODE is a
rolling code, meaning each time you connect, the car
gives a new and different OUTCODE.

PRESS THE START / STOP BUTTON

ONCE TO SWITCH THE IGNITION OFF
Please be advised AD Tech support CANNOT
help with obtaining PIN Codes or with
PRCEDURE COMPLETE
signing up to NASTF.
PRESS ENTER KEY

25 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

TIPS & HINTS

GENERAL

1. 5 keys can be programmed on NATS 5, all other system allow 4 keys.

2. NATS 5 requires a PIN code, if the large letter on the antenna label is an A, then the PIN code is 5523, however if
the letter is a B, the PIN code is random and will need to be sought from the dealer.
3. On early systems the programming procedure on the AD100 requires that you observe the engine warning light for
confirmation of key programming complete. When programming a key, wait for the engine warning light to stop
flashing- this indicates a successfully programmed key, insert the next key to be programmed at that point.
4. There are different colour transponders for various signal frequencies.
5. Fault code for "Lock out mode" (when an incorrect key has been used) can be removed with a coded key by
turning the ignition on for one minute or, when no coded keys are available, by coding keys.
6. Nissan Petrol NATS2, Fault code 225 read and fuse for headlights and engine management system faulty. Replaced
and keys programmed successfully.
7. On petrol Nissan vehicles, if a problem exists within the Engine Management system, then key programming will
be blocked. The clear time will continue, with PLEASE WAIT until the fault is cleared.
8. Some vehicles, check the vehicle fuse, as some can be missing and will prevent key programming.
9. If ERROR is received when programming keys, check the transponder that is being used for correct type.
10. Nissan Navara NATS 2/5—use ADC133 & ADC135.
11. Nissan Terrano. If communication problems are experienced try using ADC129.
12. NISSAN K12 Key will not rotate until Brake Pedal Pressed (Only on Automatic vehicles)
13. The security LED is normally mounted in the dashboard area and indicates the status of the system. When a
problem is detected, the LED will indicate the fault as listed in the following table when the IGN is ON or in
accessory position.
14. If the immobiliser has been locked (incorrect PIN entry), disconnect battery and re-connect, then turn ignition on/
off three times.

CAN SYSTEMS

1. When Programming the Intelligent System the key blade must be used to turn the ignition on & off as instructed
by tester. The key will not be programmed otherwise.
2. When programming the Non-Intelligent key the remote will be programmed at the same time.
3. When entering the security code ensure Ignition is switched off & ignition key is REMOVED.
4. If a key is inserted in the ignition and the security symbol flashes quickly this
indicates an un-programmed key.

NISSAN MICRA K12 (2003 on) SMART KEY

If the programming procedure has failed and the vehicle will crank but not start then please follow the procedure below…

1. Complete Key programming, disconnect tester and verify that the key light turns GREEN when the brake pedal is
pressed and the ignition is turned to the first position.

2. If the key light turns GREEN, the key is programmed, get out of the car and leave it for 2 minutes. Check the vehicle
starts after 2 minutes.

3. DO NOT attempt to start the vehicle immediately after key programming

FAULT CODES

P1610 NATS lock mode (unregistered key has been used)

P1611 NATS malfunction - id between BCM and ECM is not good.
P1612 NATS Malfunction - communication not possible between NATS control unit and ECM
P1614 NATS control unit cannot receive the key ID
P1615 NATS control unit receives key signal but the result of verification between the key and the NATS is not good.
AD 100 has these listed as P10, P11, P12, P14, P15 respectively.

PRECAUTIONS
IMPORTANT : PLEASE ENSURE ALL PRECAUTIONS ARE OB-
SERVED AS INDICATED AT THE FRONT OF THE OPERATING
MANUAL.

IN PARTICULAR : For vehicles fitted with STOP/START technology, the battery leads
must not be shorted together when the battery is disconnected as this can lead to damage to the car and
potential personal injury.

26 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

REMOTE PROGRAMMING

PATHFINDER

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehi-
cle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will
not be functional until you program the transmitters again.

1. Close and lock all doors with the driver’s side power lock/unlock switch.
2. Insert key into ignition and remove it from the ignition key cylinder at least six times within 10 seconds. Your Haz-
ard Lamps will flash if you have performed this step successfully. NOTE: Withdraw key completely from ignition
cylinder each time. If this procedure is performed too fast, system will not enter programming mode.
3. Insert key into the ignition cylinder and turn to the ACC position.
4. Within 5 seconds, push ANY button on the remote transmitter. Your Hazard Lamps should flash. NOTE: Do not
press the button more than one time in the above step. If the button is pressed more than one time, the program-
ming procedure will not be successful.
5. If there are any remaining transmitters (including the old ones), unlock then lock all doors using the driver’s side
power lock/unlock switch and within 5 seconds, push ANY button on the next remote. Your Hazard Lamps should
flash. Repeat this step for each transmitter (including any existing transmitters).
6. Turn the key to the OFF position, remove keys from the ignition, unlock doors using the driver’s side power lock/
unlock switch and open the driver side door.

TIIDA

1. Close all doors.

2. Lock doors with drivers side power door lock switch.
3. Insert the Key and take out the Key 6 times.
4. Doors will UNLOCK.
5. Turn Key to accessory position.
6. Lock doors with drivers side door lock switch.
7. Press button on remote control.
8. Remove Key and check operation.

ALMERA ALMERA TINO

PRIMERA MAXIMA
MICRA SERENA
VANETTE CARGO TERANO II
XTRAIL

Ensure all the doors have been unlocked, either by using a good transponder key or remote control plip key.

Procedure

1. Turn the ignition switch from Position 0 to ON 6 times within 10 seconds.

2. Then turn ignition switch to OFF position. Leave key in ignition switch.
3. After 2 seconds, the system will enter programming mode and will flash the warning lights twice.
4. Press and HOLD the unlock button on the Plip.
5. While pressing the unlock button, press the lock button 3 times.
6. Release the unlock button.
7. The warning lights will flash once to indicate successful programming.
8. Repeat procedure 4 to 7 for up to 4 plip key’s.
9. When completed turn ignition ON, and the warning lights will flash 2 times.
10. Remove key, and check all plip key’s for operation.

Note:
The programming mode will stop when either the ignition is switch ON, 4 plip keys have been programmed or no input
signal either from the switch or plip keys has been received for 120 seconds.

27 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

REMOTE PROGRAMMING

NISSAN K12—ECU Control Unit Coding

Replacing the engine control unit on Micra K12:

Code ignition keys using AD100, MVP, Tcode or Codeseeker then:

1. Turn ignition switch “ON” and wait at least 1 second.

2. Turn ignition switch “OFF” and wait at least 10 seconds.
3. Start engine and warm it up to normal operating temperature.
4. Ensure:
Battery voltage: More than 12.9V (At idle)
Engine coolant temperature: 70 - 99°C (158 - 210°F)
PNP switch: ON (Neutral selected)
Electric loads switch: OFF
5. Turn ignition switch “OFF” and wait at least 9 seconds.
6. Start the engine and let it idle for at least 28 seconds.
7. Disconnect throttle position sensor harness connector (brown), then reconnect it within 5 seconds.
8. Wait 20 seconds.
9. Make sure that idle speed is within specifications.
10. Rev up the engine two or three times. Make sure that idle speed and ignition timing are within specifications.

ITEM SPECIFICATION

Idle speed M/T: 700±50 rpm

A/T: 800±50 rpm (in “P” or “N” position)
Ignition timing M/T: 8±5° BTDC
A/T: 10±5° BTDC (in “P” or “N” position)

QUEST 1996-02

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehi-
cle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will
not be functional until you program the transmitters again.

Procedure
1. Close and lock all doors.
2. Insert and remove key from ignition 6 times within 10 seconds.
3. The parking lamps or interior lights will flash 2 times to confirm programming mode.
4. All existing remotes will be erased.
5. Insert key into ignition and turn to the accessory position ACC.
6. Press the LOCK button on the first remote transmitter to be programmed.
7. The parking lamps or interior lights will flash 2 times to confirm remote is programmed.
8. To program next remote, unlock the vehicle using the LOCK/UNLOCK switch on the drivers door.
9. Press the LOCK button on the next remote transmitter to be programmed.
10. The parking lamps or interior lights will flash 2 times to confirm remote is programmed.
11. Repeat steps 8 and 9 for all remote controls.
12. Open drivers door to exit programming mode.

ALTIMA 2000-01

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehi-
cle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will
not be functional until you program the transmitters again.

Procedure
1. Close and lock all doors.
2. Insert and remove key from ignition 6 times within 10 seconds.
3. The indicators will flash 2 times to confirm programming mode.
4. All existing remotes will be erased.
5. Insert key into ignition and turn to the accessory position ACC.
6. Press the any button on the first remote transmitter to be programmed for at least 1 second or 2 times within 5
seconds.
7. Indicators will flash 2 times to confirm remote is programmed.
8. To program next remote, unlock the vehicle using the LOCK/UNLOCK switch on the drivers door.
9. Press the any button on the next remote transmitter to be programmed for at least 1 second or 2 times within 5
seconds, indicators will flash twice to confirm programming.
10. Repeat steps 8 and 9 for all remote controls.
11. Open drivers door to exit programming mode.

28 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

REMOTE PROGRAMMING

ARMADA 2004-06 MAXIMA 2000-06

TITAN 2004-06 MURANO 2003-06
FRONTIER 2001-06 PATHFINDER 1999-04
XTERRA 2001-06 QUEST 2004-06
SENTRA 2000-06 NAVARA 2001-06

Procedure
1. Close and lock all doors.
2. Insert and remove key from ignition 6 times within 10 seconds.
3. The indicators will flash 2 times to confirm programming mode.
4. All existing remotes will be erased.
5. Insert key into ignition and turn to the accessory position ACC.
6. Press the any button on the first remote transmitter to be programmed .
7. Indicators will flash 2 times to confirm remote is programmed.
8. To program next remote, unlock the vehicle using the LOCK/UNLOCK switch on the drivers door.
9. Press the any button on the remote transmitter to be programmed.
10. Repeat steps 8 and 9 for all remote controls.
11. Open drivers door to exit programming mode.

200SX 1995-98 ALTIMA 1998-99

240SX 1995-98 FRONTIER 1998-00
SENTRA 1995-99 PATHFINDER 1996-98
350Z 2003-06 XTERRA 2000
NAVARA 1998-00

IMPORTANT: Before entering programming mode, have in possession all of the transmitters you will be using on the vehi-
cle. Once you program the transmitter, all previous codes will be erased from the memory. The other transmitters will
not be functional until you program the transmitters again.

Procedure
1. Close and lock all doors.
2. Insert and remove key from ignition 6 times within 10 seconds.
3. The indicators will flash to confirm programming mode.
4. All existing remotes will be erased.
5. Insert key into ignition and turn to the accessory position ACC.
6. Press the LOCK button on the first remote transmitter to be programmed.
7. Indicators will flash to confirm remote is programmed.
8. To program next remote, unlock the vehicle using the LOCK/UNLOCK switch on the drivers door.
9. Press the LOCK on the next remote control, and indicators will flash twice to confirm programming.
10. Repeat steps 8 and 9 for all remote controls.
11. Open drivers door to exit programming mode.

300ZX 1994-96 ALTIMA 2002-06

MAXIMA 1995-99

Procedure
1. Close and lock all doors.
2. Open the trunk/tailgate.
3. Insert and remove key from ignition 6 times within 10 seconds.
4. The indicators will flash 2 times to confirm programming mode.
5. All existing remotes will be erased.
6. Unlock the vehicle using the drivers door LOCK/UNLOCK button.
7. Press the LOCK button on the first remote transmitter to be programmed.
8. To program next remote, unlock the vehicle using the LOCK/UNLOCK switch on the drivers door.
9. Press the LOCK on the next remote control, and indicators will flash twice to confirm programming.
10. Repeat steps 8 and 9 for all remote controls.
11. Open drivers door to exit programming mode.

29 Version 4.2 MAY 2013 Copyright 2013

 COPYRIGHT 2013

AD900Pro AD600 AD35

Transponder Cloning Code Wizard Pro Remote Control Tester
PINCODE Generator

The most advanced key transponder AD600 is a software program AD35 is an innovative remote control
cloning tool in the market - that that supports various vehicle tester developed to assist with the
reads, writes, copies, a wide range of manufacturers and provides the diagnosis of all types of (IR) Infra
automotive transponders world- ability to generate immobiliser Red & (RF) Radio Frequency remote
wide. Complimenting the AD100Pro / PINCODES, mechanical key controls for all makes & models.
MVPPro. codes including dealer tool
security codes.

w w w . a d v a n c e d - d i a g n o s t i c s . c o m
™

30 Version 4.2 MAY 2013 Copyright 2013