Product description settings can be adjusted by a Win- can be applied with normal reflectors Start-up Ԏ The sensor can

rmal reflectors Start-up Ԏ The sensor can be reset to its facto-

Ԏ The mic+ sensor with two switching dows® Software. with sufficient function reserve. When Î Connect the power supply. ry setting, see »Key lock and facto-
outputs measures the distance to Safety Notes using good reflectors, such as a calm Î Set the parameters of the sensor ry setting«, Diagram 3.
an object within the detection zone Ԏ Read the operating instructions water surface, the sensor can also be manually via TouchControl (see Show parameters
contactless. Depending on the ad- prior to start-up. used up to its maximum range. Ob- Fig. 3 and Diagram 1) Î In normal operating mode shortly
justed detect distance the switching Ԏ Connection, installation and ad- jects that strongly absorb (e.g. plastic Î or use the Teach-in procedure to
push T1. The LED display shows
output is set. justment works may only be car- foam) or diffusely reflect sound (e.g. adjust the detect points (see Dia- »PAr.«
Ԏ All settings are done with two push- pebble stones) can also reduce the gram 2).
ried out by expert personnel. Each time you tap push-button T1 the
buttons and a three-digit LED-dis- Ԏ No safety component in ac- defined operating range. cm mm % Measuring Range actual settings of the analogue output
play (TouchControl). cordance with the EU Machine Synchronisation 3-digit are shown.
Ԏ Three-colour LEDs indicate the swit- LED-display
Directive, use in the area of per- If the assembly distance of multiple
ching status. sonal and machine protection sensors falls below the values shown
LED D1 and D2
Ԏ The output functions are changea-
not permitted in Fig. 1 the integrated synchronisati- T1 D1D2 T2
Push-buttons T1 and T2
ble from NOC to NCC. on should be used. Connect Sync/
Ԏ The sensors are adjustable manually Proper Use Fig. 3: TouchControl/LED display
Operating Manual mic+ ultrasonic sensors are used for Com-channels (pin 5 at the units re-
via TouchControl or via Teach-in ceptable) of all sensors (10 maximum). Factory setting
mic+ Ultrasonic Sensors procedure. non-contact detection of objects.
mic+ sensors are delivered factory
with two switching outputs Ԏ Useful additional functions are set
made with the following settings:
in the Add-on-menu. The mic+ sensors have a blind zone
mic+25/DD/TC mic+25/EE/TC Ԏ Switching outputs on NOC
mic+35/DD/TC mic+35/EE/TC Ԏ Using the LinkControl adapter (op- in which distance measurement is not
Ԏ Detecting distance at operating ran-
mic+130/DD/TC mic+130/EE/TC tional accessory) all TouchControl possible. The operating range indi- mic+25... ≥0.35 m ≥2.50 m
mic+340/DD/TC mic+340/EE/TC cates the distance of the sensor that ge and half operating range
mic+600/DD/TC mic+600/EE/TC
and additional sensor parameter mic+35... ≥0.40 m ≥2.50 m Ԏ Measurement range set to maxi-
mic+130... ≥1.10 m ≥8.00 m mum range
Diagram 1: Set sensor parameters numerically using LED display
mic+340... ≥2.00 m ≥18.00 m Maintenance
mic+ sensors work maintenance free.
Start here mic+600... ≥4.00 m ≥30.00 m
Small amounts of dirt on the surface
Fig. 1: Assembly distances, indicating synchro- do not influence function. Thick layers
T1 + T2
nisation/multiplex
of dirt and caked-on dirt affect sensor
Press T1 and T2 simultaneously for about Multiplex mode function and therefore must be remo-
3 s until welcome message has passed. The Add-on-menu allows to assign an ved.
individual address »01« to »10« to Notes
each sensor connected via the Sync/ Ԏ mic+ sensors have internal tempe-
Set switching output D1 Set switching output D2
Com-channel (Pin5). The sensors per- rature compensation. Because the
form the ultrasonic measurement se- sensors heat up on their own, the
T1 T2 T1 T2 quentially from low to high address. temperature compensation reaches
Therefore any influence between the its optimum working point after
sensors is rejected. approx. 30 minutes of operation.
T1 + T2
The address »00« is reserved to syn- Ԏ During normal operating mode, a
chronisation mode and deactivates the yellow LED signals that the swit-
Set detect distance in
T1 T2
mm or cm. multiplex mode. To use synchronised ching output has connected.
mode all sensors must be set to Ԏ During normal operating mode, the
1
T1 + T2 1 2
address »00«. measured distance value is dis-
Installation played on the LED-indicator in mm
For single switching For window mode
point press T2 operation set far Î Assemble the sensor at the installa- (up to 999 mm) or cm (from
T2 until »– – –« is T1 T2 switching point in
tion location. 100 cm). Scale switches automati-
displayed. mm or cm.
Î Plug in the connector cable to the cally and is indicated by a point on
M12 connector, see Fig. 2. top of the digits.
T1 + T2
Ԏ During Teach-in mode, the hystere-
Choose » « for NCC or
2 1 sis loops are set back to factory set-
T1 T2 3 5 4 tings.
» « for NOC.
colour Ԏ If no objects are placed within the
T1 + T2 1 +UB brown
3 –UB blue
detection zone the LED-indicator
4 D2 black shows »– – –«.
2 D1 white Ԏ If no push-buttons are pressed for
T1 T2 5 Sync/Com grey 20 seconds during parameter set-
Fig. 2: Pin assignment with view onto sensor ting mode the made changes are
T1 + T2 plug and colour coding of the microso- stored and the sensor returns to
nic connection cable
normal operating mode.
Ready
Diagram 2: Set sensor parameters via Teach-in procedure Diagram 3: Key lock and factory setting

Teach-in switching output D1/D2 Activate/deactivate

Reset to factory setting
TouchControl
1 1 2 1
85%
Turn supply voltage OFF. Turn supply voltage OFF.
Set two way reflective barrier
Set switching point D1/D2 Set window limits D1/D2 Set D1/D2 NOC/NCC
D1/D2

Place object at position 1 . Place object at position 1 . Place reflector at position 1 . While pressing T1 turn While pressing T1 turn
supply voltage ON. supply voltage ON.

Press T1/T2 until countdown

Press T1/T2 until »d1«/»d2« Press T1/T2 until »d1«/»d2« Press T1/T2 until »d1«/»d2«
passed from »8 « to »0« and NOC
is shown. is shown. is shown.
or NCC symbol is displayed. Keep T1 pressed Keep T1 pressed for about
until »on« or »off« 15 s until »rESEt« has
Current measuring Current measuring Current measuring NOC symbol is displayed . passed through the display.
value value value
»on« or »off«
Place object at position 2 .
or NCC symbol
/
Current measuring »off« or »on«
value
To activate or
Press T1/T2 until countdown
To change output deactivate press T1.
Press T1/T2 until »End« is shown. Press T1/T2 until »End« is shown. passed from »8 « to »0«
characteristic press T1/T2.
and »End« is displayed.

Don´t press any

Press T1 and T2 simultaneously push-button for 20 s.
until »End« is displayed.

Normal operating mode

Normal operating mode

Diagram 4: Useful additional functions in Add-on menu (for experienced users only, settings not required for standard applications)

Start here
T1 + T2

Press T1 and T2 simultaneously for about 13 s

until »Add« is shown in the LED-display.

T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2

T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2

T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2

T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2

T2 T1

T1 + T2 »C01«: Display Minimum value: Minimum value: »F00«: no filter Defines the strength Delay in seconds Minimum value: »00«: synchronisati- To optimize multi- Minimum value: Put plane reflector Affects the size of
bright »001« »001« »F01«: standard of the chosen filter. between the detec- blind zone on plex speed the hig- sensor-distant vertically disposed in the detection zone.
tion of an object hest sensor address window limit front of sensor: in
Ready »C02«: Display
dimmed
Maximum value:
difference between
Maximum value:
difference between
filter
»F02«: averaging
»P00«: weak filter
up to
and the output of
Maximum value: ne-
arwindow limit - 1
»01« to »10«: sensor
address for multi- may be set. Maximum value: an exact distance of
»E01«: high
»E02«: standard
maximum range and maximum range and the measured dis- plex mode Setting range »01« 999 mm for 250 mm for
»C03«: Display off filter »P09«: strong filter tance in case of ob- mic+ 25... and »E03«: slight
switching point - 1 switching point - 1 »oFF«: synchronisati- to »10« mic+25/...,
»F03«: foreground ject approach (beha- mic+35/..., mic+35... and
During window During window filter ves as on-delay). on deactivated 900 mm for all other
mode operation mode operation 999 cm for types.
hysteresis influences hysteresis influences »F04«: background "00": 0 s (no delay) mic+130/...,
both switching both switching filter up to mic+340/..., Adjust display to
points. points. mic+600/... 250 mm or 900 mm.
Note "20": 20 s response Confirm calibration
Changes in the Add-on menu time with T1+T2.
may impair the sensor func-
tion.
A6, A7, A8, A10, A11, A12
have influence on the res-
ponse time of the sensor. Low power mode Hysteresis switching Hysteresis switching Measurement filter Filter strength Response time Foreground Multiplex mode Multiplex mode Measurement range Calibration Detection zone
output D1 output D2 suppression device addressing highest address display sensitivity
 Technical data
1
+UB mic+25... mic+35... mic+130... mic+340... mic+600...
2
U 4
D1 TouchControl TouchControl TouchControl TouchControl TouchControl
36 width A/F 36 width A/F 36 width A/F 36 width A/F 36 width A/F
5
D2 LED-Display LED-Display LED-Display LED-Display LED-Display
Sync/Com 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5
3 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs
–UB
2 pnp switching outputs

Ø47.5

Ø65
1
+UB

M12x1

M12x1

M12x1

M12x1

M12x1
2
U 4
E1
5
E2 19.5
Sync/Com 33
22.5
3
–UB 51 51 51 69
36
72
2 npn switching outputs 84 84 84 102 105

blind zone 0 to 30 mm 0 to 65 mm 0 to 200 mm 0 to 350 mm 0 to 600 mm

operating range 250 mm 350 mm 1,300 mm 3,400 mm 6,000 mm
maximum range 350 mm 600 mm 2,000 mm 5,000 mm 8,000 mm
angle of beam spread see detection zone see detection zone see detection zone see detection zone see detection zone
transducer frequency 320 kHz 400 kHz 200 kHz 120 kHz 80 kHz
resolution 0.025 mm 0.025 mm 0.18 mm 0.18 mm 0.18 mm

detection zones
10 cm

10 cm

2.4 m

1.2 m

1.2 m

2.4 m
0.8 m

0.4 m

0.4 m

0.8 m

1.6 m

0.8 m

0.8 m

1.6 m
20 cm

10 cm

10 cm

20 cm
5 cm

0 cm

5 cm

0 cm
for different objects:

0m
0m

0m
The dark grey areas represent the 0 cm 0 cm 0m 0m 0m
zone where it is easy to recognise
the normal reflector (round bar).
This indicates the typical operating 5 cm
10 cm 0.8 m 1.2 m
range of the sensors. The light Plate 0.4 m Plate Plate
Plate
grey areas represent the zone Plate
where a very large reflector – for 10 cm 1.6 m 2.4 m
20 cm Round bar ø 27 mm
instance a plate – can still be re- Round bar ø 10 mm Round bar ø 27 mm
Round bar ø 10 mm 0.8 m
cognised. The requirement here is 15 cm Round bar ø 10 mm 2.4 m 3.6 m
for an optimum alignment to the 30 cm
sensor. It is not possible to evalua- 1.2 m
te ultrasonic reflections outside 35 cm
20 cm 1.3 m 3.2 m 4.8 m
this area. 40 cm 3.4 m

25 cm 1.6 m 4m 6m
50 cm
30 cm 4.8 m 7.2 m
2m
60 cm
35 cm 5.6 m 8.4 m

reproducibility ±0.15 % ±0.15 % ±0.15 % ±0.15 % ±0.15 %

accuracy ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may
be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation) be deactivated 3), 0.17%/K without compensation)
operating voltage UB 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2
voltage ripple ±10 % ±10 % ±10 % ±10 % ±10 %
no-load supply current ≤ 80 mA ≤ 80 mA ≤ 80 mA ≤ 80 mA ≤ 80 mA
housing Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU;
Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam,
epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content
class of protection to EN 60529 IP 67 IP 67 IP 67 IP 67 IP 67
norm conformity EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2
type of connection 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT
controls 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl)
indicators 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs
programmable with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl
operating temperature –25 to +70 °C –25 to +70 °C –25 to +70 °C –25 to +70 °C –25 to +70 °C
storage temperature –40 to +85 °C –40 to +85 °C –40 to +85 °C –40 to +85 °C –40 to +85 °C
weight 150 g 150 g 150 g 210 g 270 g
switching hysteresis 1) 3 mm 5 mm 20 mm 50 mm 100 mm
switching frequency 2) 25 Hz 12 Hz 8 Hz 4 Hz 3 Hz
response time 2) 32 ms 64 ms 92 ms 172 ms 240 ms
time delay before availability <300 ms <300 ms <300 ms <380 ms <450 ms

order No. mic+25/DD/TC mic+35/DD/TC mic+130/DD/TC mic+340/DD/TC mic+600/DD/TC

switching output 2 x pnp, UB – 2 V, Imax = 2 x 200 mA 2 x pnp, UB – 2 V, Imax = 2 x 200 mA 2 x pnp, UB – 2 V, Imax = 2 x 200 mA 2 x pnp, UB – 2 V, Imax = 2 x 200 mA 2 x pnp, UB – 2 V, Imax = 2 x 200 mA
switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof

order No. mic+25/EE/TC mic+35/EE/TC mic+130/EE/TC mic+340/EE/TC mic+600/EE/TC

switching output 2 x npn, –UB + 2 V, Imax = 2 x 200 mA 2 x npn, –UB + 2 V, Imax = 2 x 200 mA 2 x npn, –UB + 2 V, Imax = 2 x 200 mA 2 x npn, –UB + 2 V, Imax = 2 x 200 mA 2 x npn, –UB + 2 V, Imax = 2 x 200 mA
switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof switchable NOC/NCC, short-circuit-proof
1) Can be programmed via TouchControl and LinkControl.
2) With TouchControl and LinkControl, the selected filter setting and the maximum range influence the switching frequency and the response time.
3) Can be deactivated via LinkControl.

Registration
Enclosure Type 1 The proximity switches shall be used with a
For use only in industrial Listed (CYJV/7) cable/connector assembly ra- no. 75330-19

microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E info@microsonic.de / W microsonic.de
The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features.
machinery NFPA 79 applications. ted minimum 32 Vdc, minimum 290 mA, in
the final installation.
Approved on
June 25th, 2019
*B5396*
MV-DO-041943-859287