Product description Ԏ Useful additional functions are set Safety Notes Installation Notes

Ԏ The mic+ sensor with one analogue in the Add-on menu. Ԏ Read the operating instructions Î Assemble the sensor at the installa- Ԏ mic+ sensors have internal tempe-
output measures the distance to an Ԏ Using the LinkControl adapter (op- prior to start-up. tion location. rature compensation. Because the
object within the detection zone tional accessory) and the LinkCon- Ԏ Connection, installation and ad- Î Plug in the connector cable to the sensors heat up on their own, the
contactless. A signal proportional to trol software for Windows®, all justment works may only be car- M12 connector, see Fig. 2. temperature compensation reaches
distance is created according to the Teach-in and additional sensor pa- ried out by expert personnel. its optimum working point after
adjusted window limits of the ana- rameter settings can be optionally Ԏ No safety component in ac- 2 1 approx. 30 minutes of operation.
logue characteristic curve. undertaken. cordance with the EU Machine 3 5 4 Ԏ If an object is within the set window
Ԏ The sensor automatically detects The mic+ sensors have a blind zone in Directive, use in the area of per- colour limits of the analogue output, then
1 +UB brown
the load put to the analogue output which distance measurement is not sonal and machine protection 3 –UB blue
LED D1 lights up green, if the object
and switches to current output or possible. The operating range indica- not permitted 4 – black is outside the window limits, then
voltage output respectively. tes the distance of the sensor that can Proper Use 2 I/U white LED D1 lights up red.
Ԏ All settings are done with two push- be applied with normal reflectors with 5 Sync/Com grey Ԏ The load put to the analogue out-
mic+ ultrasonic sensors are used for
buttons and a three-digit LED dis- sufficient function reserve. When non-contact detection of objects. Fig. 2: Pin assignment with view onto sensor put is detected automatically when
Operating Manual play (TouchControl). using good reflectors, such as a calm plug and colour coding of the microso- turning supply voltage on.
Ԏ Three-colour LEDs indicate all ope- water surface, the sensor can also be Synchronisation nic connection cable
Ԏ During normal operating mode, the
mic+ Ultrasonic Sensors ration conditions. used up to its maximum range. Ob- If the assembly distance of multiple Start-up measured distance value is dis-
with one analogue output Ԏ Choosing between rising and falling jects that strongly absorb (e.g. plastic sensors falls below the values shown Î Connect the power supply. played on the LED-indicator in mm
output characteristic is possible. foam) or diffusely reflect sound (e.g. in Fig. 1 the integrated synchronisati- Î Set the parameters of the sensor (up to 999 mm) or cm (from
mic+25/IU/TC on should be used. Connect Sync/
mic+35/IU/TC Ԏ The sensors are adjustable manually pebble stones) can also reduce the manually via TouchControl (see 100 cm). Scale switches automati-
mic+130/IU/TC via TouchControl or via Teach-in defined operating range. Com-channels (pin 5 at the units re- Fig. 3 and Diagram 1) cally and is indicated by a point on
mic+340/IU/TC procedure. ceptable) of all sensors (10 maximum). Î or use the Teach-in procedure to top of the digits. Alternatively a
mic+600/IU/TC adjust the detect points (see Dia- percentage scale may be set in the
Diagram 1: Set sensor parameters numerically using LED display gram 2). add-on menu. In this connection
cm mm % Measuring Range 0 % and 100 % correspond to the
mic+25... ≥0.35 m ≥2.50 m 3-digit set window limits of the analogue
Start here mic+35... ≥0.40 m ≥2.50 m
LED-display output.
T1 + T2
LED D1 and D2 Ԏ If no objects are placed within the
mic+130... ≥1.10 m ≥8.00 m Push-buttons T1 and T2 detection zone the LED-indicator
T1 D1D2 T2
Press T1 and T2 simultaneously for about mic+340... ≥2.00 m ≥18.00 m shows »– – –«.
3 s until welcome message has passed. Fig. 3: TouchControl/LED display Ԏ The sensor can be set to its factory
mic+600... ≥4.00 m ≥30.00 m
Factory setting setting, see Diagram 3.
Fig. 1: Assembly distances, indicating synchro- Ԏ If no push-buttons are pressed for
Set analogue output nisation/multiplex mic+ sensors are delivered factory
T1 T2 made with the following settings: 20 seconds during parameter set-
Multiplex mode Ԏ Rising analogue characteristic ting mode the made changes are
T1 + T2 The Add-on-menu allows to assign an Ԏ Window limits for the analogue stored and the sensor returns to
individual address »01« to »10« to output set to blind zone and opera- normal operating mode.
Set sensor-close window each sensor connected via the Sync/ ting range Show parameters
T1 T2 limit in mm or cm.
Com-channel (Pin5). The sensors per- Ԏ Measurement range set to maxi- Î In normal operating mode shortly
T1 + T2
form the ultrasonic measurement se- mum range push T1. The LED display shows
quentially from low to high address. »PAr.«
Therefore any influence between the Maintenance
T1
Set sensor-distant window
T2 limit in mm or cm. mic+ sensors work maintenance free. Each time you tap push-button T1 the
sensors is rejected. actual settings of the analogue output
The address »00« is reserved to syn- Small amounts of dirt on the surface
T1 + T2 do not influence function. Thick layers are shown.
chronisation mode and deactivates the
multiplex mode. To use synchronised of dirt and caked-on dirt affect sensor
T1
Choose rising ( ) / falling (
T2 output characetistic curve.
)
mode all sensors must be set to function and therefore must be remo-
address »00«. ved.
T1 + T2

T1 T2

T1 + T2

Ready
Diagram 2: Set sensor parameters via Teach-in procedure Diagram 3: Key lock and factory setting

Teach-in analogue output Activate/deactivate

Reset to factory setting
TouchControl
1 2

Turn supply voltage OFF. Turn supply voltage OFF.

Set window limits Set rising/falling output
characteristic curve

Place object at position 1 . While pressing T1 turn While pressing T1 turn

supply voltage ON. supply voltage ON.

Press T1 until countdown passed

Press T1 until »IU« is shown. from »8 « to »0« and symbol for
rising/falling characteristicis
Keep T1 pressed for about Keep T1 pressed for about
displayed.
3 s until »on« or »off« 13 s until »rESEt« has
Current measuring rising/falling is displayed . passed through the display.
value characteristis
»on« or »off«
Place object at position 2 .
/
Current measuring falling/rising »off« or »on«
value characteristis
To activate or
To change output characteristic
Press T1 until »End« is shown. deactivate press T1.
press T1.

Don´t press any

Press T1 and T2 simultaneously push-button for 20 s.
until »End« is displayed.

Normal operating mode

Normal operating mode

Diagram 4: Useful additional functions in Add-on menu (for experienced users only, settings not required for standard applications)

Start here
T1 + T2

Press T1 and T2 simultaneously for about 13 s

until »Add« is shown in the LED-display.

T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2

T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2

T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2 T1 T2

T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2 T1 + T2

T2 T1

T1 + T2 »C01«: Display »– – –«: Display in »Aut«: automatic »F00«: no filter Defines the strength Delay in seconds Minimum value: »00«: synchronisati- To optimize multi- Minimum value: Put plane reflector Affects the size of
bright mm or cm detection of the »F01«: standard of the chosen filter. between the detec- blind zone on plex speed the hig- sensor-distant vertically disposed in the detection zone.
load tion of an object hest sensor address window limit front of sensor: in
Ready »C02«: Display
dimmed
» «: Display in
%, 100 % at mini- »U«: voltage output
filter
»F02«: averaging
»P00«: weak filter
up to
and the output of
Maximum value: ne-
arwindow limit - 1
»01« to »10«: sensor
address for multi- may be set. Maximum value: an exact distance of
»E01«: high
»E02«: standard
the measured dis- plex mode Setting range »01« 999 mm for 250 mm for
»C03«: Display off mum measured val- »I«: current output filter »P09«: strong filter tance in case of ob- to »10« mic+25/..., mic+ 25... and »E03«: slight
ue »oFF«: synchronisati-
»F03«: foreground ject approach (beha- mic+35/..., mic+35... and
» «: Display in filter ves as on-delay). on deactivated 900 mm for all other
%, 100% at maxi- 999 cm for types.
»F04«: background "00": 0 s (no delay) mic+130/...,
mum measured val-
filter up to mic+340/..., Adjust display to
ue
mic+600/... 250 mm or 900 mm.
Note "20": 20 s response Confirm calibration
Changes in the Add-on menu time with T1+T2.
may impair the sensor func-
tion.
A6, A7, A8, A10, A11, A12
have influence on the res-
ponse time of the sensor. Lower power mode Display mode Choose current/ Measurement filter Filter strength Response time Foreground Multiplex mode Multiplex mode Measurement range Calibration Detection zone
voltage output suppression device addressing highest address display sensitivity
 Technical data
mic+25... mic+35... mic+130... mic+340... mic+600...
TouchControl 36 width A/F TouchControl 36 width A/F TouchControl 36 width A/F TouchControl 36 width A/F TouchControl 36 width A/F
LED-Display LED-Display LED-Display LED-Display LED-Display
2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5 2 Buttons M30x1.5 5
1
+UB 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs 2 Duo-LEDs
2
U 4
I/U

Ø47.5

Ø65
5
Sync/Com
3
–UB

M12x1

M12x1

M12x1

M12x1

M12x1
1 analogue output
19.5
22.5
33
36
51 51 51 69 72
84 84 84 102 105

blind zone 0 to 30 mm 0 bis 65 mm 0 to 200 mm 0 to 350 mm 0 to 600 mm

operating range 250 mm 350 mm 1,300 mm 3,400 mm 6,000 mm
maximum range 350 mm 600 mm 2,000 mm 5,000 mm 8,000 mm
angle of beam spread see detection zone see detection zone see detection zone see detection zone see detection zone
transducer frequency 320 kHz 400 kHz 200 kHz 120 kHz 80 kHz
resolution 0.025 to 0.10 mm, depending on the 0.025 to 0.17 mm, depending on the 0.18 to 0.57 mm, depending on the 0.18 to 1.5 mm, depending on the 0.18 to 2.4 mm, depending on the
window limits window limits window limits window limits window limits
detection zones
10 cm

10 cm

2.4 m

1.2 m

1.2 m

2.4 m
0.8 m

0.4 m

0.4 m

0.8 m

1.6 m

0.8 m

0.8 m

1.6 m
20 cm

10 cm

10 cm

20 cm
5 cm

0 cm

5 cm

0 cm
for different objects:

0m
0m

0m
The dark grey areas represent the 0 cm 0 cm 0m 0m 0m
zone where it is easy to recognise
the normal reflector (round bar).
This indicates the typical operating 5 cm
10 cm 0.8 m 1.2 m
range of the sensors. The light Plate 0.4 m Plate Plate
Plate
grey areas represent the zone Plate
where a very large reflector – for 10 cm 1.6 m 2.4 m
20 cm Round bar ø 27 mm
instance a plate – can still be re- Round bar ø 10 mm Round bar ø 27 mm
Round bar ø 10 mm 0.8 m
cognised. The requirement here is 15 cm Round bar ø 10 mm 2.4 m 3.6 m
for an optimum alignment to the 30 cm
sensor. It is not possible to evalua- 1.2 m
te ultrasonic reflections outside 35 cm
20 cm 1.3 m 3.2 m 4.8 m
this area. 40 cm 3.4 m

25 cm 1.6 m 4m 6m
50 cm
30 cm 4.8 m 7.2 m
2m
60 cm
35 cm 5.6 m 8.4 m

reproducibility ±0.15 % ±0.15 % ±0.15 % ±0.15 % ±0.15 %

accuracy ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may ±1 % (Temperature drift internal compensated, may
be deactivated 2), 0.17%/K without compensation) be deactivated 2), 0.17%/K without compensation) be deactivated 2), 0.17%/K without compensation) be deactivated 2), 0.17%/K without compensation) be deactivated 2), 0.17%/K without compensation)
operating voltage UB 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2 9 to 30 V DC, short-circuit-proof, Class 2
voltage ripple ±10 % ±10 % ±10 % ±10 % ±10 %
no-load supply current ≤ 80 mA ≤ 80 mA ≤ 80 mA ≤ 80 mA ≤ 80 mA
housing Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU; Brass sleeve, nickel-plated, plastic parts: PBT, TPU;
Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam, Ultrasonic transducer: polyurethane foam,
epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content epoxy resin with glass content
class of protection to EN 60529 IP 67 IP 67 IP 67 IP 67 IP 67
norm conformity EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2 EN 60947-5-2
type of connection 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT 5-pin initiator plug, PBT
controls 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl) 2 push-buttons (TouchControl)
indicators 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs 3-digit LED display, 2 three-colour LEDs
programmable with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl with TouchControl and LinkControl
operating temperature –25 to +70 °C –25 to +70 °C –25 to +70 °C –25 to +70 °C –25 to +70 °C
storage temperature –40 to +85 °C –40 to +85 °C –40 to +85 °C –40 to +85 °C –40 to +85 °C
weight 150 g 150 g 150 g 210 g 270 g
response time 1) 32 ms 64 ms 92 ms 172 ms 240 ms
time delay before availability <300 ms <300 ms <300 ms <380 ms <450 ms

order No. mic+25/IU/TC mic+35/IU/TC mic+130/IU/TC mic+340/IU/TC mic+600/IU/TC

current output 4 to 20 mA RL ≤ 100 Ω at 9 V ≤ UB ≤ 20 V RL ≤ 100 Ω at 9 V ≤ UB ≤ 20 V RL ≤ 100 Ω at 9 V ≤ UB ≤ 20 V RL ≤ 100 Ω at 9 V ≤ UB ≤ 20 V RL ≤ 100 Ω at 9 V ≤ UB ≤ 20 V
RL ≤ 500 Ω at UB ≥ 20 V RL ≤ 500 Ω at UB ≥ 20 V RL ≤ 500 Ω at UB ≥ 20 V RL ≤ 500 Ω at UB ≥ 20 V RL ≤ 500 Ω at UB ≥ 20 V
Rising/falling output characteristic Rising/falling output characteristic Rising/falling output characteristic Rising/falling output characteristic Rising/falling output characteristic
voltage output 0 to 10 V RL ≥ 100 kΩ at UB ≥ 15 V, short-circuit-proof RL ≥ 100 kΩ at UB ≥ 15 V, short-circuit-proof RL ≥ 100 kΩ at UB ≥ 15 V, short-circuit-proof RL ≥ 100 kΩ at UB ≥ 15 V, short-circuit-proof RL ≥ 100 kΩ at UB ≥ 15 V, short-circuit-proof
Rising/falling output characteristic Rising/falling output characteristic Rising/falling output characteristic Rising/falling output characteristic Rising/falling output characteristic
1) Can be programmed via TouchControl and LinkControl.
2) Can be deactivated via LinkControl.

Registration
Enclosure Type 1 The proximity switches shall be used with a
For use only in industrial Listed (CYJV/7) cable/connector assembly ra- no. 75330-19

microsonic GmbH / Phoenixseestraße 7 / 44263 Dortmund / Germany / T +49 231 975151-0 / F +49 231 975151-51 / E info@microsonic.de / W microsonic.de
The content of this document is subject to technical changes. Specifications in this document are presented in a descriptive way only. They do not warrant any product features.
machinery NFPA 79 applications. ted minimum 32 Vdc, minimum 290 mA, in
the final installation.
Approved on
June 25th, 2019
*B5398*
MV-DO-041945-859292