SPECIAL SPECIFICATION SECTION 08710S FINISH HARDWARE MicroFab/CUB-1

Page PART 1 - GENERAL 1.01 1.02 1.03 1.04 1.05 Description of Work ............................................................................................................2 References............................................................................................................................2 Submittals ............................................................................................................................3 Quality Assurance................................................................................................................3 Delivery, Storage, and Handling..........................................................................................3

PART 2 - PRODUCTS 2.01 2.02 Manufacturers ......................................................................................................................3 General Hardware Schedule ................................................................................................4

PART 3 - EXECUTION 3.01 3.02 3.03 3.04 Examination .......................................................................................................................10 Preparation .........................................................................................................................10 Installation..........................................................................................................................10 Adjustments .......................................................................................................................11

CONSTRUCTION STANDARD SPECIFICATION SECTION 08710S FINISH HARDWARE MICROFAB/CUB-1 PART 1 - GENERAL 1.01 DESCRIPTION OF WORK Section includes furnishing and installing finish hardware as scheduled and/or as called for on Contract Documents. It does not include hardware for aluminum entrance doors. 1.02 REFERENCES A. American National Standards Institute (ANSI) ANSI ANSI ANSI ANSI ANSI ANSI B. A115 SET STEEL A115 SETWOOD A156.19 A156.21 A156.22 A250.6 Steel Door and Frame Preparation for Hardware Wood Door Hardware Standards

Specification for Power Assist and Low Energy Power Operated Doors Specification for Thresholds Specification for Door Gasketing Systems Hardware on Steel Doors (Reinforcement-Application) Institute/Builders Hardware Manufacturer's

American National Standards Association (ANSI/BHMA) ANSI A156.2

Bored and Preassembles Locks and Latches, same as BHMA 601.

C. D. E. F. G.

Department of Defense (DOD) Defense Supply Center Philadelphia (DSCP) Factory Mutual (FM) International Building Code (IBC) National Fire Protection Association (NFPA) NFPA 72 NFPA 80 National Fire Alarm Code Fire Doors, Fire Windows Finish Hardware MicroFab/CUB-1

Revised: July 10, 2003

08710S-1

July 10, 2003 NFPA 101 H. 1.03 Life Safety Code

Underwriter's Laboratory, Inc. (UL)

SUBMITTALS General: Submit the following items in accordance with Conditions of Contract and Division 1, Section "Descriptive Submittals." A. Product Data: Submit manufacturer's catalog data for each item of finish hardware, include function descriptions, materials, finishes, dimensions installation and (interface requirements when necessary). Include evidence of UL listing for fire rated hardware. Quality Certification: Submit manufacturer's written certification that hardware to be used on project is Grade One quality.

B. 1.04

QUALITY ASSURANCE A. B. C. Qualifications: Finish hardware manufacturer shall have minimum of ten (10) years experience in manufacturing of hardware. Product Quality: Provide products that have been tested and are in compliance with references listed in Section 1.02 of this specification for required assemblies. Dial Combination Locks shall be installed by safe and lock companies with minimum of five (5) years experience in installation and service of combination locks. Warranties: Provide ten (10) year warranty on closers, seven (7) year warranty on cylindrical locks and latchsets and a one (1) year warranty on all other hardware.

D. 1.05

DELIVERY, STORAGE, AND HANDLING A. B. Packing and Shipping: Finish hardware shall be packed and shipped to job site in unopened boxes, clearly labeled with manufacturer's name and item description. Storage and Protection: Store finish hardware in manner to prevent damage until needed for installation.

PART 2 - PRODUCTS 2.01 MANUFACTURERS A. General: Manufacturers with capability to meet this specification include the following: 1. Kaba Mas: Spin dial combination locks. (www.kaba-mas.com) 2. Infographics: Electrical pushbutton combination locks. (www.infographics.com) 3. Honeywell: Electro-magnetic door holders. (www.honeywell.com)

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-2

July 10, 2003 4. Horton Automatics or LCN: openers. Horton: (www.hortondoors.com) LCN: (www.lcnclosers.com) 5. National Guard Products (NGP): Thresholds, door sweeps and door bottoms, weather-stripping, smoke seals, astragals. (www.ngpinc.com) 6. Precision Hardware Inc: Exit devices and key removable mullions (Precision exit devices recommended for use with Securitech electrified trim products.) (www.precisionhardware.com) 7. Sargent: Locksets, cylinders, padlocks, door closers, mullions, and latchsets. (No substitutions allowed except in the case of door closers.) (www.sargentlock.com) 8. Securitech: High security locks, electric exit device trim and electric locking hardware. (www.securitech.com) 9. Simplex: Mechanical push button combination locks. 10. Stanley: Butt hinges. (www.stanleyworks.com) 11. Trimco: Silencers, door bumpers, mop plates, kick plates, stops/holders, flush bolts, push/pull latches. (www.trimcobbw.com) 12. Von Duprin: Exit Devices, electrified exit devices and electrical power transfers. (www.vonduprin.com) B. 2.02 Substitutes: Only approved products may be substituted, except when noted. Low energy, power-operated interior door

GENERAL HARDWARE SCHEDULE A. General: Hardware shall be identified by ANSI as Grade One hardware where applicable. Where applicable, function shall be as noted on Contract Documents, or as chosen at time of Submittals. Opening Force: Maximum force for pushing or pulling open door shall be 8.5 pounds (3.9 kg) for exterior and 5 pounds (2.3 kg) for interior doors. Manufactured Units: Unless otherwise indicated in FINISH HARDWARE SCHEDULE or elsewhere in Contract Documents, provide the following hardware: 1. Butt Hinges: 4-1/2 inches (114 mm) x 4-1/2 inches (114 mm), steel, full mortise, five knuckle, ball bearing, flat tip hinges with polished and plated finish. No electric hinges will be allowed. a. Provide heavy weight hinges on exterior doors, airlock entry doors, doors with closers, and toilet room entry doors. Use Stanley FBB 168.

B. C.

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-3

July 10, 2003 b. Provide standard weight hinges on all other doors. Use Stanley FBB 179 or equal. c. Provide manufacturer's heavy-duty non-removable pins at exterior doors, designated vault type room doors, and other doors as designated on Contract Documents. 2. Electrical Power Transfer: Provide one each electrical power transfer on doors where electrified exit devices or other electrified locking hardware is specified elsewhere in Contract Documents. Use only Von Duprin EPT-10. 3. Cylindrical Lever Locksets: Keyed function locksets and non-keyed function latchsets shall exceed ANSI Grade 1 specifications. Keyed function locksets shall remain secure after withstanding 2400 inch pounds of torque applied to the locked lever. All locksets shall maintain horizontal lever position after two million cycles per ANSI A156.2. All locksets shall be mountable without the use of through bolts and shall fit in a standard 2-1/8 (55MM) bore. Locksets shall fit a minimum door stile width of 4-1/4 (108mm). Lockset levers shall not contain any plastic fillers and shall be made of solid material. Locksets shall have 2-3/4 (70mm) backset, standard. Latchbolt heads shall be one-piece stainless steel, 7/8 (22mm) diameter x (13mm) throw, (19mm) throw for pairs of doors. All keyed locksets shall be provided with six-pin lock cylinders manufactured by Sargent Manufacturing Company, New Haven, CT with no substitutions. Lock cylinders shall be provided in the Sargent LA keyway and shall be 1 bitted. SNL-NM locksmiths will provide proper restricted lock cylinder plugs and keying into the SNL-NM master key system. a. Keyed locksets shall be Sargent 11 Line Series in the following functions: (1) 28-11G04-LL Storeroom Function-for equipment and mechanical chase doors and in electronic access control applications with jamb mounted electric strikes. 28-11G05-LL Entrance Function-provide only when indicated elsewhere in Contract Documents. 28-11G37-LL Classroom Function-provide only when indicated elsewhere in Contract Documents. 28-11G71-LL Electromechanically (fail secure) Function-for use in electronic access control application using through door circuit in conjunction with electrical power transfer. 28-11G17-LL Asylum Function-for roof access doors.

(2) (3) (4)

(5)

b. Latchsets shall be Sargent 11 Line Series with the following functions: (1) 28-11U15LL Passage Function-for all doors, including utility rooms, where keyed locksets, exit devices or other auxiliary locking devices are not specified. 28-11G65-LL Privacy Bathroom Function-for single occupant bathrooms Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-4

(2)

July 10, 2003 c. Multi-Occupant Toilet Room doors, provide auxiliary latchsets. (1) Use Sargent 24-114P x 808 strike.

4. Exit Devices: Provide exit device only where specified on Contract Documents. Exit device latch bolts shall be released by depressing actuating push pad. a. For single doors and double doors with removable or fixed center mullion, exit device shall be Sargent 80 Series or Precision 1100 Series reversible rim device. The device shall have, appropriate strike and lever handle trim for application and function. (1) For Hollow Metal or Extruded Aluminum Storefront Non-Fire Rated Doors with a minimum stile width of 4 , provide Sargent Model 888 x ETL with Model 641 strike. Doors with vision lite frames or moldings protruding at device mounting location provide Precision Model 1108 x 39LA with Model 1200-06 strike. At double doors add Precision Model 822 steel removable mullions. Where contract specifies key removable mullion provide Precision Model A-KR822 head cap. For Fire Rated Doors, provide Sargent Model 12-8888 with Model 649 strike. Doors with vision lite frames or moldings protruding at device mounting location provide Precision Model FL-1108 x 39LA with Model 100-78 strike. At double doors add Precision Model FL-822 fire rated steel removable mullions. Where contract specifies key removable mullion provide Precision Model A-FL-KR822 head cap. For Extruded Aluminum Narrow Stile Storefront Doors with a minimum stile width of 1 provide Sargent 8513 x ETL or Precision 1408 x 29L rim device. For double doors use Precision 815 mullion or Sargent 650A mullion.

(2)

(3)

b. For pair of active doors without center mullion, exit devices on each leaf shall be Sargent 8700 Series or Precision 1200 Series surface vertical rod exit devices. The device shall have appropriate strikes and lever handle trim for application and function. (1) For Hollow Metal or Extruded Aluminum Storefront Non-Fire Rated Doors with a minimum stile width of 4 , provide Sargent Model 8713 x 713-8 ETL with Model 629 top strike and 624 bottom strike. Doors with vision lite frames or molding protruding at device mounting location provide Precision Model 1208 x 39LA with Model 1200-06 top strike and 020-97 bottom strike. For fire rated doors, provide Sargent Model 12-8713 x ETL with Model 629 top strike and 624 bottom strike. Doors with vision lite frames or moldings protruding at device mounting location provide Precision Model FL-1208 x 39LA with Model 1200-06 top strike and 020-97 bottom strike. For Extruded Aluminum Narrow Storefront Doors with a minimum stile width of 1 provide Sargent 8413 x ETL or Precision 1608 x Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-5

(2)

(3)

July 10, 2003 29LA concealed vertical rod device. For double doors use Sargent 650A mullion or Precision 815 mullion. c. For Single Doors and Double Doors with removable or fixed center mullion, and which are indicated to be unlocked via electric actuation device (e.g., badge reader, key pad), provide VonDuprin EL99 Series or Precision EL 1100 Series exit device with electric latch retraction. The device must be provided with the manufacturers specified power supply, appropriate strike and lever handle trim. All electrical actuated devices actuated via electronic access control systems shall have outside lever trim, which remains in a constant locked position at all times. Key override retracts latch bolt but does not unlock lever. (1) For Hollow Metal or Extruded Aluminum Storefront Non-Fire Rated Doors with a minimum stile width of 4 , provide Von Duprin Model EL99NL x 992L-NL. Doors with vision lite frames or moldings protruding at device mounting location provide Precision Model ELR1103 x 39L with Model 1200-06 strike. At double doors add Precision Model 822 steel removable mullions. Where contract specifies key removable mullion provide Precision Model A-KR822 head cap. Use device manufacturers specified power supplies and Von Duprin Electric Power Transfer Model EPT-10. At fire rated doors, provide Von Duprin Model 99-F-EL99NL x 992LNL. At double doors provide Precision Model FL-822 fire rated steel removable mullions. Where contract specifies key removable mullion provide Precision Model A-FL-KR822 head cap. Use device manufacturers specified power supplies and Von Duprin Electric Power Transfer Model EPT-10. For Extruded Aluminum Narrow Storefront Doors with a minimum stile width of 1 provide Von Duprin EL33NL x 370L rim device. For double doors use Precision 815 mullion or Sargent 650A mullion. Use device manufacturers specified power supplies and Von Duprin Electric Power Transfer Model EPT-10.

(2)

(3)

d. Vault Type Rooms (VTR): Provide Kaba Mas Model CDX-08 pedestrian door deadbolt with appropriate strike for door and jamb. Provide appropriate signage for concerns with life safety. (1) Refer to requirements for spin dial combination lock specified below.

5. Closers: Closers shall be surface mount type with parallel arms, back check, key control valves, and 50% power adjustments and shall facilitate automatic closure of door. a. Provide Sargent Model EB350 Series closers or equal on exterior doors, interior fire rated doors, doors with electro-magnetic door holders, interior doors with exit devices, push-pull devices, auxiliary latchsets and additional doors indicated on Contract Documents. 6. Spin Dial Combination Locks: Provide spin dial combination locks only when noted in Contract Documents. Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-6

July 10, 2003 a. Provide Kaba Mas Model CDX-08 pedestrian door deadbolt with strike type 1,2,3, or 9. Procure from Defense Supply Center Philadelphia (DSCP), 700 Robbins Avenue, Philadelphia, PA 19111. Ph. 215-737-2218. National Stock Number (NSN) 5340-01-469-5906. If other than #1 strike is needed, call DOD Lock Program Hotline at 800-290-7607. 7. Mechanical Push-Button Combination Locks: Provide mechanical push-button combination locks only when noted in Contract Documents. Provide Simplex Unican L1000-2B with key bypass. Provide uncombinated Falcon core 12607A. 8. Electrical Push-Button Combination Locks: Provide electrical push-button combination locks only when noted elsewhere in Contract Documents. Unless otherwise indicated, provide Infographics keypads, controllers, etc. per Contract Documents. 9. Architectural Door Trim: Kick plates shall be of heavy-duty 16-gauge (2 mm) smooth surface metal. 10. Provide Trimco 1024- 12" x 2" (305 mm x 51 mm) LDW on push side of doors scheduled for exit devices, on both sides of doors with push/pull devices or auxiliary latchsets. Electro-Magnetic Door Holder: Provide electro-magnetic door holder device only when specified in Contract Documents. The device shall be Underwriters Laboratory (UL) listed and Factory Mutual (FM) approved and shall be fail safe, conforming to NFPA 72, NFPA 80, and NFPA 101. Release device shall be so designed that it may be automatically released by power interruption and manually released by some simple and readily obvious operation. a. Provide Honeywell Series S4003 or equal for 120 VAC. Provide appropriate floor mount pedestal where needed for floor mount installation. (1) (2) In new construction, where indicated to be installed on walls, door holder shall be flush mounted. In renovation work, where indicated to be installed on walls, door holder may be surface mounted.

11. Auxiliary Hardware: Auxiliary hardware shall be provided only where specified herein and/or elsewhere on Contract Documents. a. Combination stop and holder device shall be Trimco Model 1224-5 manually operated device. b. Concave wall mount door bumpers shall be provided at doors opening onto adjacent walls. Provide Trimco Model W1276-CCS Series with appropriate fasteners. c. Floor mount door bumpers shall be provided on doors where wall type door bumpers are not provided. Provide Trimco Model W1210ES Series.

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-7

July 10, 2003 d. Provide Trimco Model 1229A neoprene door silencers on non-fire rated doors. Provide three per each door. e. Provide flexible silicone rubber smoke seal on fire rated doors in compliance with ANSI/BHMA A156.22. Use Zero 8144 Series x Door Size. f. Manual flush bolts shall be Trimco 3917 top and bottom. g. Provide weather-stripping, door sweep(s), and threshold at exterior doors in compliance with ANSI/BHMA A156.21 and A156.22. (1) (2) (3) Provide NGP 160 weather-stripping at all non-fire rated exterior doors. Provide NGP 200 NA door sweep at exterior doors. Provide NGP 424E Stainless Steel threshold at exterior doors.

h. Door Coordinators: Provide coordinator at all pairs of active doors without center mullion. Use Sargent Model 3487 with Model 3497 carry open bar. i. Astragal: (1) Provide NGP 125 NGA astragal for all other fire rated and non-fire rated double doors without center mullion where security astragal is not specified. Provide security astragal on exterior pairs of doors without center mullions and exit devices. Provide NGP 139SP.

(2)

j. Automatic door bottoms for both fire rated and non-fire rated doors shall be NGP 420NA. Comply with ANSI/BHMA A156.22. 12. Low Energy Power Operated Door Openers: On specified doors only, provide power operated door opener(s). The power opener shall be low energy, selfcontained electric operating mechanism. It shall be powered open with DC motor working through reduction gears. Provide Tormax TTX Series or equal. a. The motor shall be off when door is in closing mode. b. The door shall be capable of being manually opened or closed with power on or off without damage to mechanism. c. The opener shall include the following variable adjustments in compliance with ANSI/BHMA A156.19. (1) (2) (3) Opening Speed - three to five seconds Closing Speed - three to five seconds Time Delay Before Closing - five to twenty-five seconds

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-8

July 10, 2003 d. Opening and closing force, measured 2" (51 mm) out from lock stile of door, shall not exceed 15 pounds (6.8 kg) of force to stop door when operating in either direction. e. The opener shall include means of turning off opening force when door is stopped for one second. After stopping door, it should then close and opener shall reset itself to accept another signal. f. The opener shall be mounted in extruded aluminum cover. g. Provide two (2) 6" (152 mm) round stainless steel push plate control switches marked "Handicapped" on each side of opening, unless otherwise indicated in Contract Documents. h. Furnish 120 VAC, 60 cycle, single phase, 15-amp service to the operator. 13. Electric Strikes: When noted elsewhere in Contract Documents, provide heavyduty electric strikes fully compatible with door, frame, and hardware specified for intended application. Strike shall have latchbolt monitoring capability. D. Fire Rated Door Hardware: Fire rated door hardware shall be listed and labeled by Underwriter's Laboratories (UL) and Factory Mutual (FM) as "Fire Exit Hardware." Exit devices on fire rated doors shall not have dog down capability. Finishes: Finish for all hardware shall be US26D, plated, Satin Chrome, unless otherwise specified in Contract Documents. Fabrication: Manufacturer's hardware shall conform to published templates prepared for screw installation. Fasteners: Furnish screws for installations with each hardware item. Provide concealed fasteners for hardware units which are exposed when door is closed.

E. F. G.

PART 3 - EXECUTION 3.01 EXAMINATION A. B. 3.02 Examine materials on which hardware is to be installed to check for surface defects including warpage, which might impede performance of hardware. Proceed with installation only after unsatisfactory conditions have been corrected.

PREPARATION A. Steel Doors and Frames: Comply with ANSI/DHI A115-SET STEEL series. 1. Surface-Applied Door Hardware: Drill and tap doors and frames according to ANSI A250.6. B. Wood Doors: Comply with ANSI/DHI A115-SET WOOD series.

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-9

July 10, 2003 3.03 INSTALLATION Install hardware per manufacturer's installation instructions, being careful not to damage finish on hardware. A. B. C. D. Butt Hinges: Install minimum of 1-1/2 pair per door on doors no taller than 7 feet 2 inches (2.18 m), otherwise install two (2) pair butt hinges per door. Lock and Latches: Install locks and latches at 36 inches (914 mm) above bottom of door. Dial and Push Button Combination Locks: Install per manufacturer's installation instructions at 42 inches (1.07 m) above finish floor. Push Plate Control Switches: Install 6" (152 mm) round push plate control switches at 9" (229 mm) and 39" (991 mm) above finish floor to center line of round plates. Two (2) plates are required on each side of opening. . Thresholds: Set thresholds for exterior doors in full bed of sealant complying with requirements specified in Division 7 Section Joint Sealants.

E. 3.04

ADJUSTMENTS Hardware shall be adjusted and demonstrated to function properly. Damaged or defective hardware shall be replaced at no cost to Sandia National Laboratories (SNL).

3.05

SCHEDULE A. MicroFab:
Manufacturer Designations: ABH ABH Manufacturing Inc. NGP National Guard Products, Inc. PHI Precision Hardware Inc. ROC Rockwood Mfg. Co. RYO Ryobi SAR Sargent Manufacturing Co. SDC Security Door Controls SEL Select Products Limited SSS Security & Safety Systems UNK UNKNOWN ZER Zero International Inc. Finishes: --600 626 628 630 652 689 BLK GRY 847.437.9901 800.647.7874 734.326.7500 800.458.2424 734.595.7200 203.562.2151 805.494.0622 800.423.1174 972.713.8501 800.635.5335

NOT FINISHED Primed For Paint Satin Chromium Plated Satin Aluminum, Clear Anodized Satin Stainless Steel, 300 Series Satin Chromium Plated Aluminum Painted Black Grey

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-10

July 10, 2003

HW1 3 1 1 1 1 1 1 1 1 1 EA. EA. EA. EA. EA. EA. EA. EA. SET EA.

65 68 85 88 65B L1500 L1540 EACH OPENING TO RECEIVE: HINGE EXIT DEVICE MORTISE CYLINDER POWER SUPPLY CARD READER POWER SUPPLY CLOSER KICK PLATE GASKETING AUTOMATIC DOOR BOTTOM B809 EACH OPENING TO RECEIVE: HINGE MANUAL FLUSH BOLTS DUST PROOF STRIKE STOREROOM LOCKSET CLOSER GASKETING AUTOMATIC DOOR BOTTOM B813 1975B EACH OPENING TO RECEIVE: PADLOCK DOOR POSITION SWITCH 1972 1998A 1998B 1990 1999 EACH OPENING TO RECEIVE: CONTINUOUS HINGE MANUAL FLUSH BOLTS DUST PROOF STRIKE DEADLOCK - DOUBLE CYLINDER FLUSH PULL CLOSER THRESHOLD ASTRAGAL GASKETING DOOR POSITION SWITCH

ZBB 961 4.5 x 4.5 FL-ELR-DSS-1308 x V39L AS REQUIRED ELR-151 BY OTHERS BY OTHERS 350 8x2 LDW FH-CSK .050 2525B 522N

652 630 626 600 ----689 630 BLK 628

ZER PHI SAR PHI UNK UNK SAR ROC NGP NGP

HW2 6 1 1 1 2 1 2 EA. EA. EA. EA. EA. SET EA.

ZBB 961 4.5 x 4.5 555 570 11-04-LL 350 2525B 522N

652 626 626 626 689 BLK 628

ZER ROC ROC SAR SAR NGP NGP

HW3 1 1 EA. EA.

AS REQUIRED BY OTHERS

-----

UNK UNK

HW4 2 1 1 1 2 2 1 1 1 2 EA. EA. EA. EA. EA. EA. EA. EA. SET EA.

SL24 555 570 4874 94C 350DA 513S 158NA 172NA BY OTHERS 81B 61B 61E

628 626 626 626 626 689 630 628 628 ---

SEL ROC ROC SAR ROC SAR NGP NGP NGP UNK

HW5 1 1 1 1 1 1 EA. EA. EA. EA. EA. EA. EACH OPENING TO RECEIVE: CONTINUOUS HINGE EXIT DEVICE RIM CYLINDER POWER SUPPLY CARD READER POWER SUPPLY

SL24 ETW ELR-1403 x DSS AS REQUIRED ELR-151 BY OTHERS BY OTHERS

628 630 626 600 -----

SEL PHI SAR PHI UNK UNK

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-11

July 10, 2003

1 1 1 1 1 1 1 1 EA. EA. EA. EA. SET EA. EA. EA. PULL CLOSER OVERHEAD STOP THRESHOLD GASKETING SWEEP DOOR POSITION SWITCH TERMINAL INTERFACE BOX 628 689 630 630 BY DOOR MANUFACTURER --101VA 628 BY OTHERS --TIE1000 --BF157 350TJ 1000 513S ROC SAR ABH NGP UNK NGP UNK SSS

HW6 1 1 1 1 1 1 1 1 1 1 1 1 1 1 EA. EA. EA. EA. EA. EA. EA. EA. EA. EA. EA. SET EA. EA.

82B 85B 88C 81G 65C 68C L154 L1040 L1500A EACH OPENING TO RECEIVE: CONTINUOUS HINGE SL24 ETW EXIT DEVICE ELR-1303 x DSS RIM CYLINDER AS REQUIRED POWER SUPPLY ELR-151 CARD READER BY OTHERS POWER SUPPLY BY OTHERS PULL BF157 CLOSER 350TJ OVERHEAD STOP 1000 THRESHOLD 513S SWEEP 101VA GASKETING 172NA DOOR POSITION SWITCH BY OTHERS TERMINAL INTERFACE BOX TIE1000 1971 1983 1984 1981 1982 EACH OPENING TO RECEIVE: CONTINUOUS HINGE MANUAL FLUSH BOLTS DUST PROOF STRIKE EXIT DEVICE MORTISE CYLINDER FLUSH PULL CLOSER THRESHOLD GASKETING SWEEP ASTRAGAL DOOR POSITION SWITCH DOORS TO SWING OUT. 82 88B 68B 85D EACH OPENING TO RECEIVE: HINGE EXIT DEVICE MORTISE CYLINDER CLOSER KICK PLATE WALL STOP

628 630 626 600 ----628 689 630 630 628 628 -----

SEL PHI SAR PHI UNK UNK ROC SAR ABH NGP NGP NGP UNK SSS

HW7 2 EA. 1 EA. 1 EA. 1 EA. 1 EA. 2 EA. 2 EA. 1 EA. 1 SET 2 EA. 1 EA. 2 EA. NOTE: HW8 3 1 1 1 1 1 EA. EA. EA. EA. EA. EA.

SL24 555 570 1303 AS REQUIRED 94C 350-DA 513S 172NA 101VA 158NA BY OTHERS

628 626 626 630 626 626 689 630 628 628 628 ---

SEL ROC ROC PHI SAR ROC SAR NGP NGP NGP NGP UNK

ZBB 961 4.5 x 4.5 FL1308 x V39L AS REQUIRED 350 8x2 LDW FH-CSK .050 409

652 630 626 689 630 630

ZER PHI SAR SAR ROC ROC

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-12

July 10, 2003

1 1 SET EA. GASKETING AUTOMATIC DOOR BOTTOM 2525B 522N BLK 628 NGP NGP

HW9 3 1 1 1 1 1 1 EA. EA. EA. EA. SET EA. EA.

85C 1997C 1997D 81F 61C 61D L1500B EACH OPENING TO RECEIVE: HINGE ZBB 961 4.5 x 4.5 CLASSROOM LOCKSET 11G-37-LL CLOSER 350 KICK PLATE 8x2 LDW FH-CSK .050 GASKETING 2525B AUTOMATIC DOOR BOTTOM 522N DOOR POSITION SWITCH BY OTHERS 1976 1995 1997B 81H L1513 EACH OPENING TO RECEIVE: HINGE STOREROOM LOCKSET CLOSER WALL STOP GASKETING AUTOMATIC DOOR BOTTOM 1971B EACH OPENING TO RECEIVE: HINGE PASSAGE LATCHSET CLOSER KICK PLATE GASKETING AUTOMATIC DOOR BOTTOM 1970 1996 EACH OPENING TO RECEIVE: CONTINUOUS HINGE DEADLOCK - DOUBLE CYLINDER FLUSH PULL CLOSER THRESHOLD GASKETING SWEEP DOOR POSITION SWITCH 81C 81D 81E EACH OPENING TO RECEIVE: CONTINUOUS HINGE COORDINATOR AUTOMATIC FLUSH BOLTS DUST PROOF STRIKE STOREROOM LOCKSET CLOSER

652 626 689 630 BLK 628 ---

ZER SAR SAR ROC NGP NGP UNK

HW10 3 1 1 1 1 1 EA. EA. EA. EA. SET EA.

ZBB 961 4.5 x 4.5 11-04-LL 350 409 2525B 522N

652 626 689 630 BLK 628

ZER SAR SAR ROC NGP NGP

HW11 3 1 1 1 1 1 EA. EA. EA. EA. SET EA.

ZBB 961 4.5 x 4.5 11U-15-LL 350 8x2 LDW FH-CSK .050 2525B 522N

652 626 689 630 BLK 628

ZER SAR SAR ROC NGP NGP

HW12 1 1 1 1 1 1 1 1 EA. EA. EA. EA. EA. SET EA. EA.

SL24 4874 94C 350 DA 513S 172NA 101VA BY OTHERS

628 626 626 689 630 628 628 ---

SEL SAR ROC SAR NGP NGP NGP UNK

HW13 2 1 1 1 1 2 EA. EA. SET EA. EA. EA.

SL24FR 1600 1942 570 11-04-LL 350

628 600 626 626 626 689

SEL ROC ROC ROC SAR SAR

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-13

July 10, 2003

2 1 1 1 2 EA. SET EA. EA. EA. KICK PLATE GASKETING CLOSER BRACKET ASTRAGAL AUTOMATIC DOOR BOTTOM 8x2 LDW FH-CSK .050 30-38NA 158NA 320N 630 628 600 628 628 ROC NGP NGP NGP NGP

HW14 2 1 1 1 1 2 2 2 2 1 1 1 1 2 2 EA. EA. SET EA. EA. EA. EA. EA. EA. EA. SET EA. EA. EA. EA.

1977 1975 EACH OPENING TO RECEIVE: CONTINUOUS HINGE SL24FR 628 SEL COORDINATOR 1600 600 ROC AUTOMATIC FLUSH BOLTS 1942 626 ROC DUST PROOF STRIKE 570 626 ROC CLASSROOM LOCKSET 11G-37-LL 626 SAR CLOSER 260 689 SAR MAGNETIC LOCK 1570 628 SDC KICK PLATE 15x2 LDW FH-CSK .050 630 ROC WALL STOP 409 630 ROC THRESHOLD 513S 630 NGP GASKETING 3038NA 628 NGP CLOSER BRACKET 600 NGP ASTRAGAL 158NA 628 NGP AUTOMATIC DOOR BOTTOM 320N 628 NGP DOOR POSITION SWITCH BY OTHERS --UNK NOTE: SECURITY CONTRACTOR TO CONFIGURE MAGNETIC LOCKS FOR AN INTERLOCK SYSTEM. 1991 1992 1993 1994 L1510 L1508 L1506 L1504 L1502 EACH OPENING TO RECEIVE: HINGE ZBB 961 4.5 x 4.5 CLASSROOM LOCKSET 11G-37-LL WALL STOP 409 SILENCERS 608 62 EACH OPENING TO RECEIVE: CONTINUOUS HINGE KEYED MULLION MORTISE CYLINDER EXIT DEVICE RIM CYLINDER POWER SUPPLY CARD READER POWER SUPPLY PULL CLOSER OVERHEAD STOP THRESHOLD GASKETING SWEEP TERMINAL INTERFACE BOX

HW15 3 1 1 3 EA. EA. EA. EA.

652 626 630 GRY

ZER SAR ROC ROC

HW16 2 1 1 2 2 1 1 1 2 2 2 1 1 2 1 EA. EA. EA. EA. EA. EA. EA. EA. EA. EA. EA. EA. SET EA. EA.

SL24 KR822 AS REQUIRED ELR-1103 x DSS AS REQUIRED ELR-152 BY OTHERS BY OTHERS BF157 350TJ 1000 513S
BY DOOR MANUFACTURER

628 600 626 630 626 600 ----628 689 630 630
---

101VA TIE1000

628 ---

SEL PHI SAR PHI SAR PHI UNK UNK ROC SAR ABH NGP UNK NGP SSS

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-14

July 10, 2003

2 EA. DOOR POSITION SWITCH L1538 L1039 EACH OPENING TO RECEIVE: HINGE PASSAGE LATCHSET WALL MAGNET CLOSER GASKETING AUTOMATIC DOOR BOTTOM 85E EACH OPENING TO RECEIVE: CONTINUOUS HINGE DOUBLE CYLINDER LOCK CLOSER THRESHOLD GASKETING SWEEP DRIP STRIP DOOR POSITION SWITCH 88D 2803 2803B 2804 2804B 65D 68D EACH OPENING TO RECEIVE: CONTINUOUS HINGE STOREROOM LOCKSET CLOSER GASKETING AUTOMATIC DOOR BOTTOM L1520 EACH OPENING TO RECEIVE: HINGE W/ KEYPAD CLOSER WALL STOP GASKETING AUTOMATIC DOOR BOTTOM 1821A EACH OPENING TO RECEIVE: CONTINUOUS HINGE AUTOMATIC FLUSH BOLTS DUST PROOF STRIKE COORDINATOR INSTITUTIONAL LOCKSET CLOSER GASKETING ASTRAGAL BY OTHERS --UNK

HW17 3 1 1 1 1 1 EA. EA. EA. EA. SET EA.

ZBB 961 4.5 x 4.5 11U-15-LL 2110 350 2525B 522N

652 626 630 689 BLK 628

ZER SAR ABH SAR NGP NGP

HW18 1 1 1 1 1 1 1 1 EA. EA. EA. EA. SET EA. EA. EA.

SL24 11G-17 LL 350 8139 X 8146 172NA 101VA 16A BY OTHERS

628 626 689 628 628 628 628 ---

SEL SAR SAR NGP NGP NGP NGP UNK

HW19 1 1 1 1 1 EA. EA. EA. SET EA.

SL24 11-04-LL 350 2525B 320N

628 626 689 BLK 628

SEL SAR SAR NGP NGP

HW20 3 1 1 1 1 1 EA. EA. EA. EA. SET EA.

ZBB 961 4.5 x 4.5

ELECTRONIC LOCKSET STAND-ALONE 4213 LL

652 626 689 630 BLK 628

ZER SAR SAR ROC NGP NGP

350 409 2525B 522N

HW21 2 1 1 1 1 2 1 1 EA. SET EA. EA. EA. EA. SET EA.

SL24FR 1942 570

1600 x FILLER x BRACKETS

11G17 LL 350 DA 2525B 158NA

628 626 626 600 626 689 BLK 628

SEL ROC ROC ROC SAR SAR NGP NGP

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-15

July 10, 2003

2 EA.
AUTOMATIC DOOR BOTTOM

320N

628

NGP

HW22 1 1 1 1 1 1 EA. EA. EA. EA. SET EA.

1821B 1621 EACH OPENING TO RECEIVE: CONTINUOUS HINGE W/ KEYPAD CLOSER KICK PLATE GASKETING AUTOMATIC DOOR BOTTOM 1821 1831 EACH OPENING TO RECEIVE: CONTINUOUS HINGE CLASSROOM LOCKSET WALL MAGNET CLOSER GASKETING AUTOMATIC DOOR BOTTOM 1818B 1820A 1618B 1620 1621B EACH OPENING TO RECEIVE: CONTINUOUS HINGE CLASSROOM LOCKSET CLOSER KICK PLATE MOP PLATE GASKETING CLOSER BRACKET AUTOMATIC DOOR BOTTOM 1818 1817 1617 1618 EACH OPENING TO RECEIVE: HINGE PUSH-PULL CLOSER KICK PLATE MOP PLATE SILENCERS 1820B EACH OPENING TO RECEIVE: CYLINDER 64E 64D 60 61 80 81 EACH OPENING TO RECEIVE: CONTINUOUS HINGE COORDINATOR EXIT DEVICE

SL24FR x ETW8

ELECTRONIC LOCKSET STAND-ALONE 4213 LL

628 626 689 630 BLK 628

SEL SAR SAR ROC NGP NGP

350 8x2 LDW FH-CSK .050 2525B 320N

HW23 1 1 1 1 1 1 EA. EA. EA. EA. SET EA.

SL24FR 11G-37-LL 2110 350 2525B 320N

628 626 630 689 BLK 628

SEL SAR ABH SAR NGP NGP

HW24 1 1 1 1 1 1 1 1 EA. EA. EA. EA. EA. SET EA. EA.

SL24 11G-37-LL 350 8x2 LDW FH-CSK .050 4x2 LDW FH-CSK .050 3038NA 320N

628 626 689 630 630 628 600 628

SEL SAR SAR ROC ROC NGP NGP NGP

HW25 3 1 1 1 1 3 EA. EA. EA. EA. EA. EA.

ZBB 961 4.5 x 4.5 111 x 73 x 73L 350 8x2 LDW FH-CSK .050 4x2 LDW FH-CSK .050 608

652 630 689 630 630 GRY

ZER ROC SAR ROC ROC ROC

HW26 1 EA.

TO MATCH SYSTEM

626

SAR

HW27 2 1 1 EA. EA. EA.

SL24FR 1600 FL1801

628 600 630

SEL ROC PHI

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-16

July 10, 2003

1 1 2 2 1 1 2 EA. EA. EA. EA. SET EA. EA. D. EXIT DEVICE MORTISE CYLINDER CLOSER WALL MAGNET GASKETING ASTRAGAL AUTOMATIC DOOR BOTTOM CUB 1 Manufacturer Designations: PHI Precision Hardware Inc. NGP National Guard Products, Inc. ROC Rockwood Mfg. Co. RYO Ryobi SAR Sargent Manufacturing Co. SEL Select Products Limited ZER Zero International Inc. Finishes: --626 628 630 652 689 BLK DUR GRY HW1 1 EA. NOT FINISHED Satin Chromium Plated Satin Aluminum, Clear Anodized Satin Stainless Steel, 300 Series Satin Chromium Plated Aluminum Painted Black Dark Bronze Anodized Grey 734.326.7500 800.647.7874 800.458.2424 734.595.7200 203.562.2151 800.423.1174 800.635.5335 FL1308 x 39L AS REQUIRED 350 2110 2525B 630 626 689 630 BLK BY DOOR MANUFACTURER --320N 628 PHI SAR SAR ABH NGP UNK NGP

1850 1850D EACH OPENING TO RECEIVE: MORTISE CYLINDER

TO MATCH SYSTEM

---

SAR

HW2 1 1 1 1 1 1 1 1 EA. EA. EA. EA. EA. SET EA. EA.

1850B 1850C 1850E 1853B EXTERIOR EACH OPENING TO RECEIVE: CONTINUOUS HINGE SL24 EXIT DEVICE 1108 x V39L RIM CYLINDER TO MATCH SYSTEM CLOSER 350 THRESHOLD 513S GASKETING 172NA SWEEP 101VA DRIP STRIP 1851 1851B EACH OPENING TO RECEIVE: HINGE CLASSROOM LOCKSET CLOSER GASKETING AUTOMATIC DOOR BOTTOM

628 630 --689 630 628 628 DUR

SEL PHI SAR SAR NGP NGP NGP NGP

HW3 3 1 1 1 1 EA. EA. EA. SET EA.

ZBB 961 4.5 x 4.5 11G-37-LL 350HS 2525B 522N

652 626 689 628 628

ZER SAR SAR NGP NGP

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-17

July 10, 2003

HW4 3 1 1 3 EA. EA. EA. EA.

1852 EACH OPENING TO RECEIVE: HINGE PRIVACY LATCHSET WALL STOP SILENCERS 1853 EACH OPENING TO RECEIVE: HINGE EXIT DEVICE RIM CYLINDER CLOSER GASKETING

ZBB 961 4.5 x 4.5 11U-65-LL 409 608

652 626 630 GRY

ZER SAR ROC ROC

HW5 3 1 1 1 1 EA. EA. EA. EA. SET

ZBB 961 4.5 x 4.5 FL1108 x V39L TO MATCH SYSTEM 350 2525B

652 630 --689 BLK

ZER PHI SAR SAR NGP

END OF SECTION

Finish Hardware MicroFab/CUB-1 Revised: July 10, 2003 08710S-18