B550M DS3H AC

B550M DS3H

User's Manual
Rev. 1701

GIGABYTE will reduce paper use in order to fulfill the responsibilities of a global citizen.
Also, to reduce the impacts on global warming, the packaging materials of this product
are recyclable and reusable. GIGABYTE works with you to protect the environment.
For more product details, please visit GIGABYTE's website.
Copyright
© 2023 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.

Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE without
prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
„„ For detailed product information, carefully read the User's Manual.
„„ For quick set-up of the product, refer to the Quick Installation Guide on GIGABYTE's
website.
https://download.gigabyte.com/FileList/Manual/mb_manual_installation-guide_103.pdf?m=sw

For product-related information, check on our website at: https://www.gigabyte.com

Identifying Your Motherboard Revision

The revision number on your motherboard looks like this: "REV: X.X." For example, "REV: 1.0"
means the revision of the motherboard is 1.0. Check your motherboard revision before updating
motherboard BIOS, drivers, or when looking for technical information.

Example:
 Table of Contents

Chapter 1 Product Introduction........................................................................................4

1-1 Motherboard Layout.......................................................................................... 4

Chapter 2 Hardware Installation......................................................................................5

2-1 Installation Precautions..................................................................................... 5
2-2 Product Specifications....................................................................................... 6
2-3 Installing the CPU............................................................................................. 9
2-4 Installing the Memory...................................................................................... 10
2-5 Installing an Expansion Card.......................................................................... 11
2-6 Back Panel Connectors................................................................................... 12
2-7 Internal Connectors......................................................................................... 14

Chapter 3 BIOS Setup...................................................................................................24

Chapter 4 Installing the Operating System and Drivers.................................................26

4-1 Operating System Installation......................................................................... 26
4-2 Drivers Installation........................................................................................... 27

Chapter 5 Appendix.......................................................................................................28
5-1 Configuring a RAID Set................................................................................... 28

Regulatory Notices..................................................................................................... 29
Contact Us................................................................................................................. 32

-3-
Chapter 1 Product Introduction
1-1 Motherboard Layout

CPU_FAN
ATX_12V
KB_MS_USB

LED_C2
D_LED2
Socket AM4

DVI

ATX
DP_HDMI

U32X4

M2_WIFI (Note)
BAT

USB_LAN SYS_FAN1

LED_CPU
M_BIOS
AUDIO
DDR4_A1

DDR4_A2

DDR4_B1

DDR4_B2
M2A_CPU

110 80

PCIEX16

Realtek®
PCIEX1
B550M DS3H (AC)
GbE LAN AMD
M2B_SB

0 1 2 3

80 B550
SATA3

iTE ®
CODEC PCIEX4 Super I/O

CLR_CMOS
QFLED

D_LED1 COM F_U32 SYS_FAN2

F_AUDIO LED_C1 TPM F_USB1 F_PANEL QFLASH_PLUS

Temperature sensor

(Note) Only for B550M DS3H AC.

-4-
Chapter 2 Hardware Installation
2-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can become
damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read the user's
manual and follow these procedures:
•• Prior to installation, make sure the chassis is suitable for the motherboard.
•• Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
•• Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
•• When connecting hardware components to the internal connectors on the motherboard, make
sure they are connected tightly and securely.
•• When handling the motherboard, avoid touching any metal leads or connectors.
•• It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist strap,
keep your hands dry and first touch a metal object to eliminate static electricity.
•• Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
•• Before connecting or unplugging the power supply cable from the motherboard, make sure
the power supply has been turned off.
•• Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
•• Before using the product, please verify that all cables and power connectors of your hardware
components are connected.
•• To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
•• Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
•• Do not place the computer system on an uneven surface.
•• Do not place the computer system in a high-temperature or wet environment.
•• Turning on the computer power during the installation process can lead to damage to system
components as well as physical harm to the user.
•• If you are uncertain about any installation steps or have a problem related to the use of the
product, please consult a certified computer technician.
•• If you use an adapter, extension power cable, or power strip, ensure to consult with its installation
and/or grounding instructions.

-5-
2-2 Product Specifications
CPU ŠŠ AMD Socket AM4, support for:
AMD Ryzen™ 5000 G-Series Processors/
AMD Ryzen™ 5000 Series Processors/
AMD Ryzen™ 4000 G-Series Processors/
AMD Ryzen™ 3000 Series Processors
(Go to GIGABYTE's website for the latest CPU support list.)
Chipset ŠŠ AMD B550
Memory ŠŠ 4 x DDR4 DIMM sockets supporting up to 128 GB (32 GB single DIMM capacity)
of system memory
ŠŠ Support for DDR4 3200/2933/2667/2400/2133 MT/s memory modules
ŠŠ Dual channel memory architecture
ŠŠ Support for ECC Un-buffered DIMM 1Rx8/2Rx8 memory modules
ŠŠ Support for non-ECC Un-buffered DIMM 1Rx8/2Rx8/1Rx16 memory modules
ŠŠ Support for Extreme Memory Profile (XMP) memory modules
(Go to GIGABYTE's website for the latest supported memory speeds and memory modules.)
Onboard ŠŠ Integrated Graphics Processor:
Graphics - 1 x DVI-D port, supporting a maximum resolution of 1920x1200@60 Hz
* The DVI-D port does not support D-Sub connection by adapter.
- 1 x DisplayPort, supporting a maximum resolution of 5120x2880@60 Hz
* Support for DisplayPort 1.4 version, HDCP 2.3, and HDR.
- 1 x HDMI port, supporting a maximum resolution of 4096x2160@60 Hz
* Support for HDMI 2.1 version, HDCP 2.3, and HDR.
ŠŠ Support for up to 3 displays at the same time
ŠŠ Maximum shared memory of 16 GB
Audio ŠŠ Realtek® ALC1220-VB CODEC
* The back panel line out jack supports DSD audio.
ŠŠ High Definition Audio
ŠŠ 2/4/5.1/7.1-channel
* You can change the functionality of an audio jack using the audio software. To
configure 7.1-channel audio, access the audio software for audio settings.

LAN ŠŠ Realtek® GbE LAN chip (1 Gbps/100 Mbps/10 Mbps)

Wireless ŠŠ AzureWave Wi-Fi AW-CB304NF (Realtek® RTL8821CE) (PCB rev. 1.7)
Communication - WIFI 802.11a, b, g, n, ac, supporting 2.4/5 GHz Dual-Band
Module (Note) - BLUETOOTH 4.2
- Support for 11ac wireless standard and up to 433 Gbps data rate
(Actual data rate may vary depending on environment and equipment.)
Expansion Slots ŠŠ 1 x PCI Express x16 slot (PCIEX16), integrated in the CPU:
- AMD Ryzen™ 5000 Series/3000 Series Processors support PCIe 4.0 x16 mode
- AMD Ryzen™ 5000 G-Series/4000 G-Series Processors support PCIe 3.0
x16 mode
* For optimum performance, if only one PCI Express graphics card is to be installed,
be sure to install it in the PCIEX16 slot.
ŠŠ 1 x PCI Express x16 slot (PCIEX4), integrated in the Chipset:
- Supporting PCIe 3.0 x4 mode
ŠŠ 1 x PCI Express x1 slot (PCIEX1), integrated in the Chipset:
- Supporting PCIe 3.0 x1 mode

(Note) Only for B550M DS3H AC.

-6-
 Storage Interface ŠŠ 1 x M.2 connector (M2A_CPU), integrated in the CPU, supporting Socket 3, M key,
type 2280/22110 SSDs:
- AMD Ryzen™ 5000 Series/3000 Series Processors support SATA and PCIe 4.0
x4/x2 SSDs
- AMD Ryzen™ 5000 G-Series/4000 G-Series Processors support SATA and
PCIe 3.0 x4/x2 SSDs
ŠŠ 1 x M.2 connector (M2B_SB), integrated in the Chipset, supporting Socket 3,
M key, type 2280 SSDs:
- Supporting SATA and PCIe 3.0 x2 SSDs
ŠŠ 4 x SATA 6Gb/s connectors, integrated in the Chipset
ŠŠ Support for RAID 0, RAID 1, and RAID 10
USB ŠŠ CPU:
- 4 x USB 3.2 Gen 1 ports on the back panel
ŠŠ Chipset:
- 2 x USB 3.2 Gen 1 ports available through the internal USB header
- 6 x USB 2.0/1.1 ports (4 ports on the back panel, 2 ports available through
the internal USB header)
Internal ŠŠ 1 x 24-pin ATX main power connector
Connectors ŠŠ 1 x 8-pin ATX 12V power connector
ŠŠ 1 x CPU fan header
ŠŠ 2 x system fan headers
ŠŠ 2 x addressable LED strip headers
ŠŠ 2 x RGB LED strip headers
ŠŠ 1 x CPU cooler LED strip/RGB LED strip header
ŠŠ 2 x M.2 Socket 3 connectors
ŠŠ 4 x SATA 6Gb/s connectors
ŠŠ 1 x front panel header
ŠŠ 1 x front panel audio header
ŠŠ 1 x USB 3.2 Gen 1 header
ŠŠ 1 x USB 2.0/1.1 header
ŠŠ 1 x Trusted Platform Module (TPM) header (2x6 pin, for the GC-TPM2.0_S
module only)
ŠŠ 1 x serial port header
ŠŠ 1 x Clear CMOS jumper
ŠŠ 1 x Q-Flash Plus button
Back Panel ŠŠ 1 x PS/2 keyboard/mouse port
Connectors ŠŠ 1 x DVI-D port
ŠŠ 1 x DisplayPort
ŠŠ 1 x HDMI port
ŠŠ 2 x SMA antenna connectors (Note)
ŠŠ 4 x USB 3.2 Gen 1 ports
ŠŠ 4 x USB 2.0/1.1 ports
ŠŠ 1 x RJ-45 port
ŠŠ 3 x audio jacks
I/O Controller ŠŠ iTE® I/O Controller Chip

(Note) Only for B550M DS3H AC.

-7-
 Hardware ŠŠ Voltage detection
Monitor ŠŠ Temperature detection
ŠŠ Fan speed detection
ŠŠ Overheating warning
ŠŠ Fan fail warning
ŠŠ Fan speed control
* Whether the fan speed control function is supported will depend on the fan you install.
BIOS ŠŠ 1 x 128 Mbit flash
ŠŠ Use of licensed AMI UEFI BIOS
ŠŠ PnP 1.0a, DMI 2.7, WfM 2.0, SM BIOS 2.7, ACPI 5.0
Unique Features ŠŠ Support for APP Center
* Available applications in APP Center may vary by motherboard model. Supported
functions of each application may also vary depending on motherboard specifications.
- @BIOS
- EasyTune
- RGB Fusion
- Smart Backup
- System Information Viewer
ŠŠ Support for Q-Flash Plus
ŠŠ Support for Q-Flash
ŠŠ Support for Xpress Install
Bundled ŠŠ Norton® Internet Security (OEM version)
Software ŠŠ LAN bandwidth management software
Operating ŠŠ Support for Windows 11 64-bit
System ŠŠ Support for Windows 10 64-bit
Form Factor ŠŠ Micro ATX Form Factor; 24.4cm x 24.4cm

* GIGABYTE reserves the right to make any changes to the product specifications and product-related information without
prior notice.

&& Please visit the SERVICE/SUPPORT\Utility page on GIGABYTE's website to download the latest version
of apps.
https://www.gigabyte.com/Support/Utility/Motherboard?m=ut

-8-
2-3 Installing the CPU
Read the following guidelines before you begin to install the CPU:
•• Make sure that the motherboard supports the CPU.
(Go to GIGABYTE's website for the latest CPU support list.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
CPU to prevent hardware damage.
•• Locate the pin one of the CPU. The CPU cannot be inserted if oriented incorrectly.
•• Apply an even and thin layer of thermal grease on the surface of the CPU.
•• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage
of the CPU may occur.
•• Set the CPU host frequency in accordance with the CPU specifications. It is not recommended
that the system bus frequency be set beyond hardware specifications since it does not meet the
standard requirements for the peripherals. If you wish to set the frequency beyond the standard
specifications, please do so according to your hardware specifications including the CPU, graphics
card, memory, hard drive, etc.

Installing the CPU

Completely lift up the CPU socket locking lever. Locate the pin one (denoted by a small triangle) of the CPU
socket and the CPU. Once the CPU is positioned into its socket, place one finger down on the middle of the
CPU, lowering the locking lever and latching it into the fully locked position.

A Small Triangle
Marking Denotes Pin
One of the Socket AM4 CPU Socket

Completely lift up the

CPU socket locking lever

A Small Triangle
Marking Denotes CPU AM4 CPU
Pin One

Do not force the CPU into the CPU socket before the CPU socket locking lever is lifted up,
or damage to the CPU and CPU socket may occur.

&& Please visit GIGABYTE's website for details on hardware installation.

http://www.gigabyte.com/WebPage/210/quick-guide.html?m=sw

-9-
2-4 Installing the Memory
Read the following guidelines before you begin to install the memory:
•• Make sure that the motherboard supports the memory. It is recommended that memory of the same
capacity, brand, speed, and chips be used. (Go to GIGABYTE's website for the latest supported
memory speeds and memory modules.)
•• Always turn off the computer and unplug the power cord from the power outlet before installing the
memory to prevent hardware damage.
•• Memory modules have a foolproof design. A memory module can be installed in only one direction.
If you are unable to insert the memory, switch the direction.
Dual Channel Memory Configuration
This motherboard provides four memory sockets and supports Dual Channel Technology. After the memory
is installed, the BIOS will automatically detect the specifications and capacity of the memory. Enabling Dual
Channel memory mode will double the original memory bandwidth.
The four memory sockets are divided into two channels and each channel has two memory sockets as following:

Channel A: DDR4_A1, DDR4_A2

Channel B: DDR4_B1, DDR4_B2

* Recommended Dual Channel Memory Configuration:

DDR4_A1 DDR4_A2 DDR4_B1 DDR4_B2
2 Modules -- DS/SS -- DS/SS
4 Modules DS/SS DS/SS DS/SS DS/SS
(SS=Single-Sided, DS=Double-Sided, "- -"=No Memory)

Due to CPU limitations, read the following guidelines before installing the memory in Dual Channel mode.
1. Dual Channel mode cannot be enabled if only one memory module is installed.
2. When enabling Dual Channel mode with two or four memory modules, it is recommended that memory of
the same capacity, brand, speed, and chips be used.

DDR4_A1
DDR4_A2
DDR4_B1
DDR4_B2

When installing a single memory module, we recommend that you install it in the DDR4_A2
or DDR4_B2 socket.

- 10 -
2-5 Installing an Expansion Card
Read the following guidelines before you begin to install an expansion card:
•• Make sure the motherboard supports the expansion card. Carefully read the manual that came
with your expansion card.
•• Always turn off the computer and unplug the power cord from the power outlet before installing an
expansion card to prevent hardware damage.

Follow the steps below to correctly install your expansion card in the expansion slot.
1. Locate an expansion slot that supports your card. Remove the metal slot cover from the chassis back panel.
2. Align the card with the slot, and press down on the card until it is fully seated in the slot.
3. Make sure that the expansion card is fully seated in its slot.
4. Secure the card's metal bracket to the chassis back panel with a screw.
5. After installing all expansion cards, replace the chassis cover(s).
6. Turn on your computer. If necessary, go to BIOS Setup to make any required BIOS changes for your
expansion card(s).
7. Install the driver provided with the expansion card in your operating system.

PCIEX16 Slot

- 11 -
2-6 Back Panel Connectors
(Note 4)

(Note 3)

USB 2.0/1.1 Port

The USB port supports the USB 2.0/1.1 specification. Use this port for USB devices.
PS/2 Keyboard/Mouse Port
Use this port to connect a PS/2 mouse or keyboard.
DVI-D Port (Note 1)(Note 2)
The DVI-D port conforms to the DVI-D specification and supports a maximum resolution of 1920x1200@60 Hz
(the actual resolutions supported depend on the monitor being used). Connect a monitor that supports
DVI-D connection to this port.
DisplayPort (Note 2)
DisplayPort delivers high quality digital imaging and audio, supporting bi-directional audio transmission.
DisplayPort can support both DPCP and HDCP 2.3 content protection mechanisms. It provides improved
visuals supporting Rec. 2020 (Wide Color Gamut) and High Dynamic Range (HDR) for Blu-ray UHD
playback. You can use this port to connect your DisplayPort-supported monitor. Note: The DisplayPort
Technology can support a maximum resolution of 5120x2880@60 Hz but the actual resolutions supported
depend on the monitor being used.
HDMI Port (Note 2)
The HDMI port is HDCP 2.3 compliant and supports Dolby TrueHD and DTS HD
Master Audio formats. It also supports up to 192KHz/24bit 7.1-channel LPCM audio
output. You can use this port to connect your HDMI-supported monitor. The maximum supported resolution is
4096x2160@60 Hz, but the actual resolutions supported are dependent on the monitor being used.
After installing the DisplayPort/HDMI device, make sure to set the default sound playback device
to DisplayPort/HDMI. (The item name may differ depending on your operating system.)
Triple-Display Configurations for the Onboard Graphics:
Triple-display configurations are supported after you install motherboard drivers in OS.
USB 3.2 Gen 1 Port
The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0
specification. Use this port for USB devices.
USB 3.2 Gen 1 Port (Q-Flash Plus Port)
The USB 3.2 Gen 1 port supports the USB 3.2 Gen 1 specification and is compatible to the USB 2.0
specification. Use this port for USB devices. Before using Q-Flash Plus (Note 3), make sure to insert the
USB flash drive into this port first.

(Note 1) The DVI-D port does not support D-Sub connection by adapter.
(Note 2) For AMD Ryzen™ 5000 G-Series/4000 G-Series Processors only.
(Note 3) To enable the Q-Flash Plus function please visit the "Unique Features" webpage of GIGABYTE's website.
(Note 4) Only for B550M DS3H AC.

- 12 -
SMA Antenna Connectors (Note 4)
Use this connector to connect an antenna.
Tighten the antennas to the antenna connectors and then aim the antennas correctly for better
signal reception.

RJ-45 LAN Port

The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. The following
describes the states of the LAN port LEDs.
Connection/
Connection/Speed LED: Activity LED:
Speed LED Activity LED
State Description State Description
Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring
Green 100 Mbps data rate Off No data transmission or receiving is occurring

LAN Port
Off 10 Mbps data rate

Line In/Rear Speaker Out (Blue)

The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line Out/Front Speaker Out (Green)
The line out jack.
Mic In/Center/Subwoofer Speaker Out (Pink)
The Mic in jack.

Audio Jack Configurations:

Headphone/
Jack 4-channel 5.1-channel 7.1-channel
2-channel
Line In/Rear Speaker Out a a a

Line Out/Front Speaker Out a a a a

Mic In/Center/Subwoofer a a
Speaker Out
Front Panel Line Out/ a
Side Speaker Out

You can change the functionality of an audio jack using the audio software. To configure
7.1-channel audio, access the audio software for audio settings.
&& Please visit GIGABYTE's website for details on configuring the audio software.
https://www.gigabyte.com/WebPage/698/realtek1220-audio.html

•• When removing the cable connected to a back panel connector, first remove the cable from
your device and then remove it from the motherboard.
•• When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
- 13 -
2-7 Internal Connectors

1 3 7

10
4

6
9

9
8

11 7 5 16 15 14 13 17 12 4 18

1) ATX_12V 10) BAT

2) ATX 11) F_AUDIO
3) CPU_FAN 12) F_PANEL
4) SYS_FAN1/SYS_FAN2 13) F_U32
5) D_LED1/D_LED2 14) F_USB1
6) LED_CPU 15) COM
7) LED_C1/LED_C2 16) TPM
8) SATA3 0/1/2/3 17) CLR_CMOS
9) M2A_CPU/M2B_SB 18) QFLASH_PLUS

Read the following guidelines before connecting external devices:

•• First make sure your devices are compliant with the connectors you wish to connect.
•• Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
•• After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
- 14 -
1/2) ATX_12V/ATX (2x4 12V Power Connector and 2x12 Main Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
on the motherboard. Before connecting the power connector, first make sure the power supply is turned
off and all devices are properly installed. The power connector possesses a foolproof design. Connect the
power supply cable to the power connector in the correct orientation.
The 12V power connector mainly supplies power to the CPU. If the 12V power connector is not connected,
the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.

ATX_12V:
Pin No. Definition Pin No. Definition
5 8 1 GND (Only for 2x4-pin 12V) 5 +12V (Only for 2x4-pin 12V)
1 4 2 GND (Only for 2x4-pin 12V) 6 +12V (Only for 2x4-pin 12V)
ATX_12V 3 GND 7 +12V
4 GND 8 +12V

ATX:
12 24 Pin No. Definition Pin No. Definition
1 3.3V 13 3.3V
2 3.3V 14 -12V
3 GND 15 GND
4 +5V 16 PS_ON (soft On/Off)
5 GND 17 GND
6 +5V 18 GND
7 GND 19 GND
8 Power Good 20 NC
9 5VSB (stand by +5V) 21 +5V
10 +12V 22 +5V
11 +12V (Only for 2x12-pin 23 +5V (Only for 2x12-pin ATX)
1 13 ATX)
12 3.3V (Only for 2x12-pin 24 GND (Only for 2x12-pin ATX)
ATX)
ATX

- 15 -
 B

3/4) CPU_FAN/SYS_FAN1/SYS_FAN2 (Fan Headers)

_ S
All fan headers on this motherboard are 4-pin. Most fan headers possess a foolproof insertion design.
When connecting a fan cable, be sure to connectS_it in the correct orientation (the black connector wire
is the ground wire). The motherboard supports CPU_ fan speed control, which requires the use of a CPU
B
fan with fan speed control design. For optimum heat dissipation, it is recommended that a system fan be
installed inside the chassis.
_ U
U _ F
_ _ 3 B 1
Pin No. Definition
1 1 GND
F_USB3 F 2 Voltage Speed Control
CPU_FAN
SYS_FAN1 3 Sense
4 PWM Speed Control
_ _0
1

SYS_FAN2
F

_ _B _ S _

U
_ F
_0

_0

_ F
_

_3
•• Be sure to connect fan cables to the fan headers to prevent your CPU and system from
overheating. Overheating may result in damage to the CPU or the system may hang.
•• These fan headers are not configuration jumper blocks. Do not place a jumper cap on the headers.

_
_0 F
5) D_LED1/D_LED2 (Addressable LED Strip Headers)
The headers can be used to connect a standard 5050 addressable LED strip, with maximum power rating
of 5A (5V) and maximum number of 1000 LEDs.

Pin No. Definition

1
_ S F_ 1 V (5V)
S _

1 2 Data
D_LED1 D_LED2 3 No Pin
4 GND
B S S_F B_
Connect your addressable LED
strip to the header. The power pin
_

F_USB30 3

(marked with a triangle on the plug)

B_
_

Addressable
of the LED strip must be connected
to Pin 1 of the addressable LED_3
S S_F

F LED Strip
_ U
S F_

strip header. Incorrect connection

1 may lead to the damage of the
_
_B

LED strip.
B

F_USB3
_

For how to turn on/off the lights of the LED strip please visit the "Unique Features" webpage of
GIGABYTE's website.

Before installing
F_USB3 the devices, be sure
F_USB30 3 to turn off the devices and your computer. Unplug the power
B_
cord from the power outlet to prevent damage to the devices.
B

- 16 -
B_
_
_

_
6) LED_CPU (CPU Cooler LED Strip/RGB LED Strip Header)
The header can be used to connect a CPU cooler LED strip or a standard 5050 RGB LED strip (12V/G/R/B),
with maximum power rating of 2A (12V) and maximum length of 2m.

Pin No. Definition

1 12V
2 G
1
3 R
4 B
DEBUG
PORT Connect the CPU cooler LED strip/
RGB LED strip to the header. The
power pin (marked with a triangle on
RGB LED
Strip
the plug) of the LED strip must be
connected to Pin 1 (12V) of this header.
Incorrect connection may lead to the
1
12V
damage of the LED strip.

7) LED_C1/LED_C2 (RGB LED Strip Headers)

DEBUG
The headers can be used to connect
PORT a standard 5050 RGB LED strip (12V/G/R/B), with maximum power
rating of 2A (12V) and maximum length of 2m.

1
Pin No. Definition
1 12V
1 2 G
LED_C1 LED_C2 3 R
DEBUG

4 B
PORT

Connect your RGB LED strip to the

header. The power pin (marked with
a triangle on the plug) of the LED strip
RGB
LED Strip must be connected to Pin 1 (12V) of
this header. Incorrect connection may
1
lead to the damage of the LED strip.
12V

For how to turn on/off the lights of the LED strip please visit the "Unique Features" webpage of
GIGABYTE's website.

Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.

- 17 -
B3 F
S _

_0
_ F
8) SATA3 0/1/2/3 (SATA 6Gb/s Connectors)
The SATA connectors conform to SATA 6Gb/s standard and are compatible with SATA 3Gb/s and SATA
1.5Gb/s standard. Each SATA connector supports a single SATA device. The SATA connectors support
S _ RAID 0, RAID 1, and RAID 10. Refer to Chapter 3, "Configuring a RAID Set," for instructions on configuring
a RAID array.
_ F
_0 F
SATA3

Pin No. Definition

1 7 3
1 GND
2 TXP
_0 F 3 TXN
1 7 4 GND
2
1
5 RXN
1 7
0 6 RXP
1 7 7 GND

_3 U
PORT
DEBUG

9) M2A_CPU/M2B_SB (M.2 Socket 3 Connectors)

PORT
_3 U
The M.2 connectors support M.2 SATA SSDs or M.2 PCIe SSDs and support RAID configuration. Please
DEBUG

note that an M.2 PCIe SSD cannot be used to create a RAID set either with an M.2 SATA SSD or a SATA
PORT

hard drive. Please navigate to the "Configuring a RAID Set" page of GIGABYTE's website for instructions
DEBUG

on configuring a RAID array.

PORT
DEBUG

M2A_CPU
110 80

M2B_SB
80

Follow the steps below to correctly install an M.2 SSD in the M.2 connector.
Step 1:
Locate the proper mounting hole for the M.2 SSD to be installed and then install the mounting clip first.
Step 2:
Pull the clip's tab up and out of the mounting hole. Slide the M.2 SSD into the connector at an angle.
Step 3:
Press the M.2 SSD down and then secure it by pressing the clip's tab into the mounting hole.

- 18 -
10) BAT (Battery)
The battery provides power to keep the values (such as BIOS configurations, date, and time information)
in the CMOS when the computer is turned off. Replace the battery when the battery voltage drops to a low
level, or the CMOS values may not be accurate or may be lost.

You may clear the CMOS values by removing the battery:

1. Turn off your computer and unplug the power cord.
2. Gently remove the battery from the battery holder and wait for one
minute. (Or use a metal object like a screwdriver to touch the positive
and negative terminals of the battery holder, making them short for
5 seconds.)
3. Replace the battery.
4. Plug in the power cord and restart your computer.
•• Always turn off your computer and unplug the power cord before replacing the battery.
•• Replace the battery with an equivalent one. Damage to your devices may occur if the battery is
replaced with an incorrect model.
•• Contact the place of purchase or local dealer if you are not able to replace the battery by yourself
or uncertain about the battery model.
•• When installing the battery, note the orientation of the positive side (+) and the negative side (-)
of the battery (the positive side should face up).
•• Used batteries must be handled in accordance with local environmental regulations.

11) F_AUDIO (Front Panel Audio Header)

The front panel audio header supports High Definition audio (HD). You may connect your chassis front
panel audio module to this header. Make sure the wire assignments of the module connector match the
pin assignments of the motherboard header. Incorrect connection between the module connector and the
motherboard header will make the device unable to work or even damage it.

Pin No. Definition

1 MIC L
9 1 2 GND
10 2 3 MIC R
4 NC
5 Head Phone R
6 MIC Detection
7 SENSE_SEND
8 No Pin
9 Head Phone L
Head Phone
10
Detection

Some chassis provide a front panel audio module that has separated connectors on each wire
instead of a single plug. For information about connecting the front panel audio module that has
different wire assignments, please contact the chassis manufacturer.

- 19 -
 12) F_PANEL (Front Panel Header)
Connect the power switch, reset switch, speaker, chassis intrusion switch/sensor and system status indicator
on the chassis to this header according to the pin assignments below. Note the positive and negative pins
before connecting the cables.

Power LED Power Switch Speaker

PLED+

PW+

SPEAK+

SPEAK-
PLED-

PW-

NC
NC
F_ U F_ 2 20 F_
1 19

CI+
HD-

RES+

PWR_LED+
PWR_LED-
PWR_LED-
CI-
HD+

RES-
Hard Drive Reset Power LED
Activity LED Switch
Chassis Intrusion
Header

•• PLED/PWR_LED (Power LED):

B_ System Status LED Connects

B SS to the power status indicator on the chassis front panel. The LED
S0 On is on when the system is operating. The LED is off when the system is in S3/
1

S3/S4/S5 Off S4 sleep state or powered off (S5).

_S
1
1

•• PW (Power Switch):
Connects to the power switch on the chassis front panel. You may configure the way to turn off your _
system using the power switch (please navigate to the "BIOS Setup" page of GIGABYTE's website and B
search for "Settings\Platform Power"
S for more information).
•• SPEAK (Speaker):
1 2 3
1 2 3

Connects to the speaker on the chassis front panel. The system reports system startup status by issuing
a beep code. One single short beep will be heard if no problem is detected at system startup.
1 2 3

S B_
•• HD (Hard Drive Activity LED): 1 2 3

B
Connects
S to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive
is reading or writing data.
•• RES (Reset Switch):
Connects to the reset switch on the chassis front panel. Press the reset switch to restart the computer
if the computer freezes and fails to perform a normal restart. _ S
•• CI (Chassis Intrusion Header):
S_
Connects to the chassis intrusion switch/sensor on the chassis that can detect if the chassis cover has
_
been removed. This function requires a chassis with a chassis intrusion switch/sensor. B
•• NC: No connection.
_ U
B SS S U _
3
_ _ 3 B

F_USB3 F
The front panel design may differ by chassis. A front panel module mainly consists of power switch,
reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis
S F
front panel module to this header,
_ make sure the wire assignments and the pin assignments are
matched correctly.

- 20 -
_ _B _ S _
13) F_U32 (USB 3.2 Gen 1 Header)
The header conforms to USB 3.2 Gen 1 and USB 2.0 specification and can provide two USB ports. For
purchasing the optional 3.5" front panel that provides two USB 3.2 Gen 1 ports, please contact the local
dealer.
1 10

F_USB30 F_ U

20 11

Pin No. Definition Pin No. Definition

1 VBUS 11 D2+
2 SSRX1- 12 D2-
3 SSRX1+ 13 GND
4 GND 14 SSTX2+
5 SSTX1- 15 SSTX2-
6 SSTX1+ 16 GND
B_
7 GND 17 SSRX2+
8 D1- 18 SSRX2-
9 D1+ 19 VBUS
10 NC 20 No Pin

14) F_USB1 (USB 2.0/1.1 Header)

The header conforms to USB 2.0/1.1 specification. Each USB header can provide two USB ports via an
optional USB bracket. For purchasing the optional USB bracket, please contact the local dealer. S

9 1
10 2

Pin No. Definition Pin No. Definition

1 Power (5V) 6 USB DY+
2 Power (5V) 7 GND
3 USB DX- 8 GND
4 USB DY- S 93 No Pin B SS
5 USB DX+ 10 NC

S _
S F

Prior to installing the USB bracket, be sure to turn off your computer and unplug the power cord
from the power outlet to prevent damage to the USB bracket.

B_
- 21 -
 1

15) COM (Serial Port Header)

_S
The COM header can provide one serial port via an optional COM port cable. For purchasing the optional
1

COM port cable, please contact the local dealer.

_ B S_
B B

1 2 3
1 2 3

Pin No. Definition Pin No. Definition

1 2 3

S B_ 1 NDCD- 6 NDSR-
2 3
9 1
B 2 NSIN 7 NRTS-
10 2
3 NSOUT 8 NCTS-
4 NDTR- 9 NRI-
5 GND 10 No Pin
_ S

S_
_
B

_ U
U _ F
_ _ 3 B

F_USB3 F

16) TPM (Trusted Platform Module Header)

_ _0
You may connect a TPM (Trusted Platform Module) to this header.

_ _B _ S _

Pin No. Definition Pin No. Definition _ F

_
1 LAD0 7 LAD3
11 1 2 VCC3 8 GND
12 2 3 9
LAD1 LFRAME
4 No Pin 10 NC
_ 5 LAD2 11 SERIRQ
_0 F
6 LCLK 12 LRESET

_ S F_

B S S_F B_

- 22 -

_ F _3 U
17) CLR_CMOS (Clear CMOS Jumper)
Use this jumper to clear the BIOS configuration and reset the CMOS values to factory defaults. To clear
the CMOS values, use a metal object like a screwdriver to touch the two pins for a few seconds.

Open: Normal

Short: Clear CMOS Values

•• Always turn off your computer before clearing the CMOS values.
•• After system restart, go to BIOS Setup to load factory defaults (select Load Optimized Defaults) or
manually configure the BIOS settings (please navigate to the "BIOS Setup" page of GIGABYTE's
website for more information).

18) QFLASH_PLUS (Q-Flash Plus Button)

Q-Flash Plus allows you to update the BIOS when your system is off (S5 shutdown state). Save the latest
BIOS on a USB thumb drive and plug it into the Q-Flash Plus port, and then you can now flash the BIOS
automatically by simply pressing the Q-Flash Plus button. The QFLED will flash when the BIOS matching
and flashing activities start and will stop flashing when the main BIOS flashing is complete.

QFLED

QFLASH_PLUS

For how to use Q-Flash Plus please visit the "Unique Features" webpage of GIGABYTE's
website.

- 23 -
 Chapter 3 BIOS Setup
BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the
motherboard. Its major functions include conducting the Power-On Self-Test (POST) during system startup,
saving system parameters and loading operating system, etc. BIOS includes a BIOS Setup program that allows
the user to modify basic system configuration settings or to activate certain system features.

When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to
keep the configuration values in the CMOS.

To access the BIOS Setup program, press the <Delete> key during the POST when the power is turned on.

To upgrade the BIOS, use either the GIGABYTE Q-Flash or @BIOS utility.
•• Q-Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system.
•• @BIOS is a Windows-based utility that searches and downloads the latest version of BIOS from the Internet
and updates the BIOS.
For instructions on using the Q-Flash and @BIOS utilities, please navigate to the "Unique Features" page of
GIGABYTE's website and search for "BIOS Update Utilities."

•• Because BIOS flashing is potentially risky, if you do not encounter problems using the current
version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with
caution. Inadequate BIOS flashing may result in system malfunction.
•• It is recommended that you not alter the default settings (unless you need to) to prevent system
instability or other unexpected results. Inadequately altering the settings may result in system's
failure to boot. If this occurs, try to clear the CMOS values and reset the board to default values.
•• Refer to the introductions of the battery/clear CMOS jumper in Chapter 2 or navigate to the "BIOS
Setup" page of GIGABYTE's website and search for "Load Optimized Defaults" for how to clear
the CMOS values.

&& Please visit GIGABYTE's website for details on configuring BIOS Setup.
https://www.gigabyte.com/WebPage/954/amd500-bios.html

- 24 -
Startup Screen:

The following startup Logo screen will appear when the computer boots.

Function Keys

Function Keys:
<DEL>: BIOS SETUP\Q-FLASH
Press the <Delete> key to enter BIOS Setup or to access the Q-Flash utility in BIOS Setup.

<F12>: BOOT MENU

Boot Menu allows you to set the first boot device without entering BIOS Setup. In Boot Menu, use the up
arrow key <h> or the down arrow key <i> to select the first boot device, then press <Enter> to accept.
The system will boot from the device immediately.
Note: The setting in Boot Menu is effective for one time only. After system restart, the device boot order
will still be based on BIOS Setup settings.

<END>: Q-FLASH
Press the <End> key to access the Q-Flash utility directly without having to enter BIOS Setup first.

- 25 -
Chapter 4 Installing the Operating System and Drivers
4-1 Operating System Installation
With the correct BIOS settings, you are ready to install the operating system.

As some operating systems already include RAID driver, you do not need to install separate RAID driver
during the Windows installation process. After the operating system is installed, we recommend that you install
all required drivers from the GIGABYTE APP Center to ensure system performance and compatibility. If the
operating system to be installed requires that you provide additional RAID driver during the OS installation
process, please refer to the steps below:

Step 1:
Go to GIGABYTE's website, browse to the motherboard model's web page, download the AMD RAID Preinstall
Driver file on the Support\Download\SATA RAID/AHCI page, unzip the file and copy the files to your USB
thumb drive.

Step 2:
Boot from the Windows setup disc and perform standard OS installation steps. When the screen requesting you
to load the driver appears, select Browse.

Step 3:
Insert the USB thumb drive and then browse to the location of the driver. Select AMD-RAID Bottom Device first
and click Next to load the driver. Then select AMD-RAID Controller and click Next to load the driver. Finally,
continue the OS installation.

- 26 -
4-2 Drivers Installation
After you install the operating system, a dialog box will appear on the bottom-right corner of the desktop asking
if you want to download and install the drivers and GIGABYTE applications via APP Center. Click Install to
proceed with the installation. (In BIOS Setup, make sure Settings\IO Ports\APP Center Download & Install
Configuration\APP Center Download & Install is set to Enabled.)

When the End User License Agreement dialog box appears, press <Accept> to install APP Center. On the APP
Center screen, select the drivers and applications you want to install and click Install.

Before the installation, make sure the system is connected to the Internet.

&& Please visit GIGABYTE's website for more software information.

https://www.gigabyte.com/WebPage/320/am4-app-center.html?m=sw

&& Please visit GIGABYTE's website for more troubleshooting information.

https://www.gigabyte.com/WebPage/351/faq.html

- 27 -
Chapter 5 Appendix
5-1 Configuring a RAID Set
RAID Levels
RAID 0 RAID 1 RAID 10
Minimum Number of
≥2 2 4
Hard Drives
Number of hard drives * (Number of hard drives/2) *
Array Capacity Size of the smallest drive
Size of the smallest drive Size of the smallest drive
Fault Tolerance No Yes Yes

Before you begin, please prepare the following items:

This motherboard supports RAID 0, RAID 1, and RAID 10. Prepare the correct number of hard drives as indicated
in the table above before configuring a RAID array.
•• SATA hard drives or SSDs. To ensure optimal performance, it is recommended that you use two hard drives
with identical model and capacity.
•• Windows setup disc.
•• An Internet connected computer.
•• A USB thumb drive.

An M.2 PCIe SSD cannot be used to set up a RAID set with a SATA hard drive.

&& Please visit GIGABYTE's website for details on configuring a RAID array.
https://www.gigabyte.com/WebPage/313/am4-raid.html?m=sw

- 28 -
Regulatory Notices
United States of America, Federal Communications Commission Statement

Supplier's Declaration of Conformity

47 CFR § 2.1077 Compliance Information

Product Name: Motherboard

Trade Name: GIGABYTE
Model Number: B550M DS3H AC/B550M DS3H

Responsible Party – U.S. Contact Information: G.B.T. Inc.

Address: 17358 Railroad street, City Of Industry, CA91748
Tel.: 1-626-854-9338
Internet contact information: https://www.gigabyte.com

FCC Compliance Statement:

This device complies with Part 15 of the FCC Rules, Subpart B, Unintentional Radiators.
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.

The FCC with its action in ET Docket 96-8 has adopted a safety standard for human exposure to radio frequency (RF) electromagnetic energy emitted
by FCC certified equipment. The Intel PRO/Wireless 5000 LAN products meet the Human Exposure limits found in OET Bulletin 65, 2001, and ANSI/
IEEE C95.1, 1992. Proper operation of this radio according to the instructions found in this manual will result in exposure substantially below the FCC's
recommended limits.

The following safety precautions should be observed:

•• Do not touch or move antenna while the unit is transmitting or receiving.
•• Do not hold any component containing the radio such that the antenna is very close or touching any exposed parts of the body, especially the face
or eyes, while transmitting.
•• Do not operate the radio or attempt to transmit data unless the antenna is connected; if not, the radio may be damaged.
•• Use in specific environments:
- The use of wireless devices in hazardous locations is limited by the constraints posed by the safety directors of such environments.
- The use of wireless devices on airplanes is governed by the Federal Aviation Administration (FAA).
- The use of wireless devices in hospitals is restricted to the limits set forth by each hospital.

Antenna use: damage to this device. The maximum allowed antenna gain for use with
In order to comply with FCC RF exposure limits, low gain integrated this device is 6dBi in order tocomply with the E.I.R.P limit for the 5.25-to
antennas should be located at a minimum distance of 7.9 inches (20 cm) 5.35 and 5.725 to 5.85 GHz frequency range in point-to-point operation. To
or more from the body of all persons. comply with RF exposure requirements all antennas should be located at a
Explosive Device Proximity Warning minimum distance of 20cm, or the minimum separation distance allowed
Warning: Do not operate a portable transmitter (such as a wireless network by the module approval, from the body of all persons.
device) near unshielded blasting caps or in an explosive environment Attention: l'utilisation d'un réseau sans fil IEEE802.11a est restreinte à
unless the device has been modified to be qualified for such use. une utilisation en intérieur à cause du fonctionnement dansla bande de
Antenna Warning fréquence 5.15-5.25 GHz. Industry Canada requiert que ce produit soit
The wireless adapter is not designed for use with high-gain antennas. utilisé à l'intérieur des bâtiments pour la bande de fréquence 5.15-5.25 GHz
afin de réduire les possibilités d'interférences nuisibles aux canaux
Use On Aircraft Caution co-existants des systèmes de transmission satellites. Les radars de
Caution: Regulations of the FCC and FAA prohibit airborne operation of puissances ont fait l'objet d'une allocation primaire de fréquences dans
radio-frequency wireless devices because their signals could interfere with les bandes 5.25-5.35 GHz et 5.65-5.85 GHz. Ces stations radar peuvent
critical aircraft instruments. créer des interférences avec ce produit et/ou lui être nuisible. Le gain
Other Wireless Devices d'antenne maximum permissible pour une utilisation avec ce produit
Safety Notices for Other Devices in the Wireless Network: Refer to the est de 6 dBi afin d'être conforme aux limites de puissance isotropique
documentation supplied with wireless Ethernet adapters or other devices rayonnée équivalente (P.I.R.E.) applicable dans les bandes 5.25-5.35 GHz
in the wireless network. et 5.725-5.85 GHz en fonctionnement point-à-point. Pour se conformer aux
conditions d'exposition de RF toutes les antennes devraient être localisées
Canada, Canada-Industry Notice: à une distance minimum de 20 cm, ou la distance de séparation minimum
This device complies with Industry Canada license-exempt RSS permise par l'approbation du module, du corps de toutes les personnes.
standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and Under Industry Canada regulations, this radio transmitter may only operate
(2) this device must accept any interference, including interference that using an antenna of a type and maximum (or lesser) gain approved for
may cause undesired operation of the device. the transmitter by Industry Canada. To reduce potential radio interference
Cet appareil est conforme aux normes Canada d'Industrie de RSS to other users, the antenna type and its gain should be chosen so that
permis-exempt. L'utilisation est assujetti aux deux conditions suivantes: the equivalent isotropically radiated power (e.i.r.p.) is not more than that
(1) le dispositif ne doit pas produire de brouillage préjudiciable, et necessary for successful communication.
(2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage Conformément à la réglementation d'Industrie Canada, le présent émetteur
susceptible de provoquer un fonctionnement indésirable. radio peut fonctionner avec une antenne d'un type et d'un gain maximal
Caution: When using IEEE 802.11a wireless LAN, this product is restricted (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le
to indoor use due to its operation in the 5.15-to 5.25-GHz frequency but de réduire les risques de brouillage radio électrique à l'intention des
range. Industry Canada requires this product to be used indoors for the autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte
frequency range of 5.15 GHz to 5.25 GHz to reduce the potential for que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
harmful interference to co-channel mobile satellite systems. High power l'intensité nécessaire à l'établissement d'une communication satisfaisante.
radar is allocated as the primary user of the 5.25-to 5.35-GHz and 5.65 to
5.85-GHz bands. These radar stations can cause interference with and/or

- 29 -
European Union (EU) CE Declaration of Conformity CE Declaración de conformidad
This device complies with the following directives: Electromagnetic Este producto que llevan la marca CE cumplen con las siguientes
Compatibility Directive 2014/30/EU, Low-voltage Directive 2014/35/EU, Directivas de la Unión Europea: Directiva EMC 2014/30/EU, Directiva de
Radio Equipment Directive 2014/53/EU, ErP Directive 2009/125/EC, RoHS bajo voltaje 2014/35/EU, Directiva de equipamentos de rádio 2014/53/EU,
directive (recast) 2011/65/EU & the 2015/863 Statement. Directiva RoHS 2011/65/EU y la Declaración 2015/863.
This product has been tested and found to comply with all essential El cumplimiento de estas directivas se evalúa mediante las normas
requirements of the Directives. europeas armonizadas.
European Union (EU) RoHS (recast) Directive 2011/65/EU & the CE Dichiarazione di conformità
European Commission Delegated Directive (EU) 2015/863 Statement I prodotti con il marchio CE sono conformi con una o più delle seguenti
GIGABYTE products have not intended to add and safe from hazardous Direttive UE, come applicabile: Direttiva EMC 2014/30/UE, Direttiva sulla
substances (Cd, Pb, Hg, Cr+6, PBDE, PBB, DEHP, BBP, DBP and DIBP). bassa tensione 2014/35/UE, Direttiva di apparecchiature radio 2014/53/
The parts and components have been carefully selected to meet RoHS UE, Direttiva RoHS 2011/65/EU e Dichiarazione 2015/863.
requirement. Moreover, we at GIGABYTE are continuing our efforts to La conformità con tali direttive viene valutata utilizzando gli Standard
develop products that do not use internationally banned toxic chemicals. europei armonizzati applicabili.
European Union (EU) Community Waste Electrical & Electronic Deklaracja zgodności UE Unii Europejskiej
Equipment (WEEE) Directive Statement Urządzenie jest zgodne z następującymi dyrektywami: Dyrektywa
GIGABYTE will fulfill the national laws as interpreted from the 2012/19/ kompatybilności elektromagnetycznej 2014/30/UE, Dyrektywa
EU WEEE (Waste Electrical and Electronic Equipment) (recast) directive. niskonapięciowej 2014/35/UE, Dyrektywa urządzeń radiowych 2014/53/
The WEEE Directive specifies the treatment, collection, recycling and UE, Dyrektywa RoHS 2011/65/UE i dyrektywa2015/863.
disposal of electric and electronic devices and their components. Under Niniejsze urządzenie zostało poddane testom i stwierdzono jego zgodność
the Directive, used equipment must be marked, collected separately, and z wymaganiami dyrektywy.
disposed of properly.
ES Prohlášení o shodě
WEEE Symbol Statement Toto zařízení splňuje požadavky Směrnice o Elektromagnetické
The symbol shown below is on the product or on its kompatibilitě 2014/30/EU, Směrnice o Nízkém napětí 2014/35/EU,
packaging, which indicates that this product must not be Směrnice o rádiových zařízeních 2014/53/EU, Směrnice RoHS 2011/65/
disposed of with other waste. Instead, the device should be EU a 2015/863.
taken to the waste collection centers for activation of the Tento produkt byl testován a bylo shledáno, že splňuje všechny základní
treatment, collection, recycling and disposal procedure. požadavky směrnic.

For more information about where you can drop off your waste equipment EK megfelelőségi nyilatkozata
for recycling, please contact your local government office, your household A termék megfelelnek az alábbi irányelvek és szabványok
waste disposal service or where you purchased the product for details of követelményeinek, azok a kiállításidőpontjában érvényes, aktuális
environmentally safe recycling. változatában: EMC irányelv 2014/30/EU, Kisfeszültségű villamos
berendezésekre vonatkozó irányelv 2014/35/EU, rádióberendezések
Battery Information irányelv 2014/53/EU, RoHS irányelv 2011/65/EU és 2015/863.
European Union—Disposal and recycling information
GIGABYTE Recycling Program (available in some regions) Δήλωση συμμόρφωσης ΕΕ
Είναι σε συμμόρφωση με τις διατάξεις των παρακάτω Οδηγιών
της Ευρωπαϊκής Κοινότητας: Οδηγία 2014/30/ΕΕ σχετικά με την
ηλεκτρομαγνητική συμβατότητα, Οοδηγία χαμηλή τάση 2014/35/EU,
Οδηγία 2014/53/ΕΕ σε ραδιοεξοπλισμό, Οδηγία RoHS 2011/65/ΕΕ
και 2015/863.
This symbol indicates that this product and/or battery should not be Η συμμόρφωση με αυτές τις οδηγίες αξιολογείται χρησιμοποιώντας τα
disposed of with household waste. You must use the public collection ισχύοντα εναρμονισμένα ευρωπαϊκά πρότυπα.
system to return, recycle, or treat them in compliance with the local
regulations.
End of Life Directives-Recycling
The symbol shown below is on the product or on its packaging, D33006
RoHS
which indicates that this product must not be disposed of with
other waste. Instead, the device should be taken to the waste
collection centers for activation of the treatment, collection,
recycling and disposal procedure.
Déclaration de Conformité aux Directives de l'Union européenne (UE)
Cet appareil portant la marque CE est conforme aux directives de l'UE
suivantes: directive Compatibilité Electromagnétique 2014/30/UE, directive
Basse Tension 2014/35/UE, directive équipements radioélectriques
2014/53/UE, la directive RoHS II 2011/65/UE & la déclaration 2015/863.
La conformité à ces directives est évaluée sur la base des normes
européennes harmonisées applicables.
European Union (EU) CE-Konformitätserklärung
Dieses Produkte mit CE-Kennzeichnung erfüllen folgenden EU-Richtlinien:
EMV-Richtlinie 2014/30/EU, Niederspannungsrichtlinie 2014/35/EU,
Funkanlagen Richtlinie 2014/53/EU, RoHS-Richtlinie 2011/65/EU erfüllt
und die 2015/863 Erklärung.
Die Konformität mit diesen Richtlinien wird unter Verwendung der
entsprechenden Standards zurEuropäischen Normierung beurteilt.
CE declaração de conformidade
Este produto com a marcação CE estão em conformidade com das
seguintes Diretivas UE: Diretiva Baixa Tensão 2014/35/EU; Diretiva
CEM 2014/30/EU; Diretiva RSP 2011/65/UE e a declaração 2015/863.
A conformidade com estas diretivas é verificada utilizando as normas
europeias harmonizadas.

- 30 -
European Community Radio Equipment Directive Compliance Statement:

This equipment complies with all the requirements and other relevant provisions of Radio Equipment Directive 2014/53/EU.
This equipment is suitable for home and office use in all the European Community Member States and EFTA Member States.
The low band 5.15 -5.35 GHz is for indoor use only.
AT BE BG CH CY CZ DE
DK EE EL ES FI FR HR
HU IE IS IT LI LT LU
LV MT NL PL PT RO SE
SI SK TR UK

NCC Wireless Statements / 無線設備警告聲明：

低功率電波輻射性電機管理辦法
(1) 取得審驗證明之低功率射頻器材，非經核准，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特
性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至
無干擾時方得繼續使用。前述合法通信，指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或
工業、科學及醫療用電波輻射性電機設備之干擾。
(2) 應避免影響附近雷達系統之操作。

Korea KCC NCC Wireless Statement:

5,25GHz - 5,35 GHz 대역을 사용하는 무선 장치는 실내에서만 사용하도록 제한됩니다 .

Japan Wireless Statement:

5.15 GHz 帯 ~ 5.35 GHz 帯 : 屋内のみの使用。

Wireless module approvals:

Wireless module manufacturer: Realtek Semiconductor Corp.
Wireless module model name: RTL8821CE

- 31 -
 Contact Us

GIGA-BYTE TECHNOLOGY CO., LTD.

Address: No.6, Baoqiang Rd., Xindian Dist., New Taipei City 231
TEL: +886-2-8912-4000, FAX: +886-2-8912-4005
Tech. and Non-Tech. Support (Sales/Marketing) : https://esupport.gigabyte.com
WEB address (English): https://www.gigabyte.com
WEB address (Chinese): https://www.gigabyte.com/tw

•• GIGABYTE eSupport
To submit a technical or non-technical (Sales/Marketing) question, please link to:
https://esupport.gigabyte.com

- 32 -