ENGLISH

Unidirectional opening sensor

for automatic sliding doors
User’s Guide for product version 0100 and higher
See product label for serial number
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOUR PRINTING

DESCRIPTION

1. radar antenna
2. potentiometer
3. cover
4. main connector 3
5. DIP-switch

4
1
5

2
©BEA | Original instructions | 42.7808 / V1 - 06.13

TECHNICAL SPECIFICATIONS
Technology: microwave doppler radar
Transmitter frequency: 24.150 GHz
Transmitter radiated power: < 20 dBm EIRP
Transmitter power density: < 5 mW/cm²
Detection mode: motion
Min. detection speed: 5 cm/s (measured in sensor axis)
Supply voltage: 12 V to 24 V AC ±10%; 12 V to 24 V DC +30% / -10%
Mains frequency: 50 to 60 Hz
Max power consumption: <2W
Output: relay (free of potential change-over contact)
Max. contact voltage: 42 V AC/DC
Max. contact current: 1 A (resistive)
Max. switching power: 30 W (DC) / 60 VA (AC)
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | INFO@BEA.BE | WWW.BEA.BE
Mounting height: from 1.8 m to 3 m
Degree of protection: IP54
BEA hereby declares that the VIO-M1 is in conformity with the basic requirements and the other relevant provisions Temperature range: from -20 °C to + 55 °C
of the directive 1999/5/EC.
Angleur, June 2013 Pierre Gardier, Authorized representative and responsible for technical documentation Dimensions: 180 mm (L) x 58 mm (H) x 50 mm (W)
The complete declaration of conformity is available on our website: www.bea-pedestrian.be Tilt angles: 15° to 45° vertical; -15° to +15° lateral
Applicable directives: R&TTE 1999/5/EC
For EC countries: according to the directive 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE)
Specifications are subject to changes without prior notice. Measured in specific conditions.
 TROUBLESHOOTING
1 MOUNTING & WIRING

1 2 12-24 V
COM
The door remains The sensor power is off. 1 Check the wiring and the power supply.
closed.
NO-NC
The LED is OFF.

The door does not Improper output 1 Change the output configuration setting on
react as expected. configuration on the sensor. each sensor connected to the door operator.

The door closes and The sensor is disturbed by 1 Make sure the sensor is fixed properly.
Apply the mounting template. Fix the sensor firmly and
opens constantly. the closing of the door or 2 Make sure the detection mode is unidirectional.
Drill 1 hole for the cable and connect the cable.
vibrations caused by the 3 Increase the antenna angle.
pull it through.
door motion. 4 Increase the immunity filter.
Drill 2 holes for the screws.
5 Reduce the field size.

The door opens for It rains and the sensor 1 Make sure the detection mode is unidirectional.
no apparent reason. detects the motion of the 2 Increase the immunity filter.
2 ADJUSTMENTS rain drops. 3 Use a rain accessory.

In highly reflective 1 Change the antenna angle.

environments, the sensor 2 Decrease the field size.
DIP 4
DIP-SWITCH

DIP 1 DIP 2 DIP 3

detects objects outside of its 3 Increase the immunity filter.
DETECTION MODE OUTPUT CONFIG. PRM-MODE IMMUNITY FILTER
detection field.

In airlock vestibules, 1 Change the antenna angle.

ON unidirectional NC for PRM* high
the sensor detects the 2 Increase the immunity filter.
movement of
OFF bidirectional NO normal normal the opposite door.

*PRM= persons with reduced mobility

DIP 1 needs to be ON for this function
FIELD SIZE

MIN MAX
2.2 m 2.2 m

vertical angle: 30°

SAFETY INSTRUCTIONS
ANGLE

- Test the good functioning of the installation before leaving the premises.
- The device cannot be used for purposes other than its intended use. All other uses cannot be guaranteed by the manufacturer
2.2 m 2.2 m of the sensor.
- The manufacturer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system
in compliance with applicable national and international regulations and standards on door safety.
- The manufacturer of the sensor cannot be held responsible for incorrect installations or inappropriate adjustments of the sensor.
- Only trained and qualified personnel may install and setup the sensor.
- The warranty is void if unauthorized repairs are made or attempted by unauthorized personnel.
- Avoid touching any electronic components, avoid vibrations, do not cover the sensor and avoid proximity to neon lamps or moving
objects.
field size: max - The door control unit and the door cover profile must be correctly earthed.

VIO-M1 VIO-M1