HCD-MD1EX

SERVICE MANUAL US Model

Canadian Model
AEP Model
UK Model
Ver 1.1 2001.02 E Model

HCD-MD1EX is the Amplifier, CD player,

Mini disc Deck and Tuner section in
CMT-MD1.

U.S. and foreign patents licensed form Dolby Laboratories Model Name Using Similar Mechanism HCD-MD333
Licensing Corporation. CD
Base Unit Name BU-22BD19
Section
Optical Pick-up Name KSS-213B/K-N
Model Name Using Similar Mechanism HCD-MD333
MD
Mechanism Name MDM-3J
Section
Optical Pick-up Name KMS-260A/J1N

SPECIFICATIONS

– Continued on next page –

COMPACT Hi-Fi COMPONENT SYSTEM

9-922-950-12 Sony Corporation
2001B0500-1 Audio Entertainment Group
C 2001.2 General Engineering Dept.
–2–
SELF-DIAGNOSIS FUNCTION
The self-diagnosis function consists of error codes for users which are displayed automatically when errors occur, and error codes which
show the error history in the test mode during servicing. For details on how to view error codes for users, refer to the following box in the
instruction manual. For details on how to perform checks during servicing, refer to the following “Procedure for Using the Self-Diagnosis
Function (Error History Display Mode)”.

Procedure for Using the Self-Diagnosis Function (Error History Display Mode)
Note: Perform the self-diagnosis function in the “error history display mode” in the test mode. The following describes the least required steps. Be careful
not to enter other modes by mistake. If other modes are set accidentally, press the ^ (CD) button to exit that mode.

1. With the power off, press the =0 button while pressing the [VOLUME–] button.
2. Press the [VOLUME+/–] button to display “ERR DP MODE”.
3. Pressing the p (CD) button sets the error history mode and displays “total rec”.
4. Select the contents to be displayed or executed with pressing the [VOLUME+/–] button.
5. Pressing the 6 (CD) button displays or executes the contents selected.
6. Pressing the 6 (CD) button another time returns to step 4.
7. Pressing the ^ (CD) button displays “ERR DP MODE” and exits the error history mode.
8. To exit the test mode, press the p (MD) button while pressing the [FUNCTION] button.
The unit sets into the STANDBY state, and the test mode ends.

–3–
ITEM OF ERROR HISTORY MODE ITEMS AND CONTENTS
Selecting the Test Mode

Display Details of History

total rec Displays the recording time in the form of “rππππππh”.
The displayed time is the total number of hours the laser is high power, which is about one-fourth of the actual
recording time. The time is displayed in decimal digits between 0h to 65535h.
total play Displays the playback time in the form of “pππππππh”.
The displayed time is the total actual play time. The paused time is not counted. The time is displayed in
decimal digits between 0h to 65535h.
retry err Displays the total number of retries during recording and retry errors during playback in the form of “rππpππ”.
“r” indicates the retries during recording while “p” indicates the retry errors during playback. The number of
retries is displayed in hexadecimal digits between 00 to FF.
total err Displays the total number of errors in the form of “total ππ”.
The number of errors is displayed in hexadecimal digits between 00 to FF.
err history Displays the 10 latest errors in the form of “0π E@@”.
The π indicates the history number. The smaller the number, the newer is the error. (00 is the latest error.)
The @@ indicates the error code. Refer to the following table for details. Press the [VOLUME+/–] button to
switch the error history.
er refresh? Mode which erases all the error histories.
The error history serves as a reference for when to replace the optical pick-up. Perform this procedure when the
optical pick-up has been replaced in order to erase past error histories and not at other times. Press the p (CD)
button when “er refresh??” is displayed. The history will be erased and “Complete!” will be displayed momen-
tarily. Be sure to check the following when this mode has been executed.
• Check that the data has been erased.
• Perform recording and playback, and check that the mechanism operates normally.

Table of Error Codes

Error Code Details of Error Error Code Details of Error
E00 No error E05 FOK has deviated
E01 Disc error. Cannot read PTOC E06 Unfocused (Servo has deviated)
(Disc is ejected out) E07 Recording retry
E02 Disc error. UTOC error E08 Recording retry error
(Disc is not ejected out) E09 Play retry error
E03 Loading error (Access error)
E04 Cannot read address (Servo has deviated) E0A Playback retry error (C2 error)

–4–
 TABLE OF CONTENTS

SELF-DIAGNOSIS FUNCTION ................................... 3

1. SERVICING NOTES .............................................. 6

2. GENERAL .................................................................. 9

3. DISASSEMBLY ......................................................... 12

4. SERVICE MODE ...................................................... 19

5. TEST MODE .............................................................. 20

6. ELECTRICAL ADJUSTMENTS
MD Section ..................................................................... 26
CD Section ...................................................................... 31

7. DIAGRAMS
7-1. Block Diagram – CD Section – ..................................... 33
7-2. Block Diagram – MD Section – .................................... 35
7-3. Block Diagram – MAIN Section – ................................ 37
7-4. Block Diagram
– DISPLAY/POWER SUPPLY Section – ..................... 39
7-5 Note for Printed Wiring Boards and
Schematic Diagrams ....................................................... 42
7-6. Printed Wiring Board – BD (CD) Section – .................. 43
7-7. Schematic Diagram – BD (CD) Section – ...................... 45
7-8. Printed Wiring Board – BD (MD) Section – ................. 47
7-9. Schematic Diagram – BD (MD) Section (1/3) – ............ 49
7-10. Schematic Diagram – BD (MD) Section (2/3) – ............ 51
7-11. Schematic Diagram – BD (MD) Section (3/3) – ............ 53
7-12. Printed Wiring Board – MAIN Board (side A) – .......... 55
7-13. Printed Wiring Board – MAIN Board (side B) – .......... 57
7-14. Schematic Diagram – MAIN Section (1/2) – ................ 59
7-15. Schematic Diagram – MAIN Section (2/2) – ................ 61
7-16. Printed Wiring Boards – PANEL Section – .................. 63
7-17. Schematic Diagram – PANEL Section – ........................ 65
7-18. Printed Wiring Boards
– AMP/TRANSFORMER Section – .............................. 67
7-19. Schematic Diagram
– AMP/TRANSFORMER Section – .............................. 69
7-20. Printed Wiring Board – POWER Section – ................... 71
7-21. Schematic Diagram – POWER Section – ...................... 73
7-22. Printed Wiring Boards – MOTOR/SW Section – ......... 75
7-23. Schematic Diagram – MOTOR/SW Section – ............... 76
7-24. IC Pin Function Description ........................................... 86

8. EXPLODED VIEWS ................................................ 96

9. ELECTRICAL PARTS LIST ............................. 103

–5–
 SECTION 1
SERVICING NOTES
Flexible Circuit Board Repairing NOTES ON HANDLING THE OPTICAL PICK-UP
• Keep the temperature of the soldering iron around 270 ˚C dur- BLOCK OR BASE UNIT
ing repairing.
• Do not touch the soldering iron on the same conductor of the The laser diode in the optical pick-up block may suffer electro-
circuit board (within 3 times). static break-down because of the potential difference generated
• Be careful not to apply force on the conductor when soldering by the charged electrostatic load, etc. on clothing and the human
or unsoldering. body.
During repair, pay attention to electrostatic break-down and also
Notes on chip component replacement use the procedure in the printed matter which is included in the
• Never reuse a disconnected chip component. repair parts.
• Notice that the minus side of a tantalum capacitor may be dam- The flexible board is easily damaged and should be handled with
aged by heat. care.

NOTES ON LASER DIODE EMISSION CHECK

CAUTION
The laser beam on this model is concentrated so as to be focused
Danger of explosion if battery is incorrectly replaced.
on the disc reflective surface by the objective lens in the optical
Replace only with the same or equivalent type recommended by
pick-up block. Therefore, when checking the laser diode emis-
the manufacturer.
sion, observe from more than 30 cm away from the objective lens.
Discard used batteries according to the manufacturer’s instructions.
LASER DIODE AND FOCUS SEARCH OPERATION
ADVARSEL! CHECK
Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri Carry out the “S curve check” in “CD section adjustment” and
af samme fabrikat og type. check that the S curve waveforms is output three times.
Levér det brugte batteri tilbage til leverandøren.
Notes on chip component replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
ADVARSEL aged by heat.
Eksplosjonsfare ved feilaktig skifte av batteri.
Benytt samme batteritype eller en tilsvarende type Flexible Circuit Board Repairing
anbefalt av apparatfabrikanten. • Keep the temperature of the soldering iron around 270 ˚C dur-
Brukte batterier kasseres i henhold til fabrikantens ing repairing.
instruksjoner. • Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
VARNING • Be careful not to apply force on the conductor when soldering
Explosionsfara vid felaktigt batteribyte. or unsoldering.
Använd samma batterityp eller en likvärdig typ som
rekommenderas av apparattillverkaren.
Kassera använt batteri enligt gällande föreskrifter. Note:
Be sure to connect all wires (including FFC) in the MD
VAROITUS section before applying power or ICs may be damaged.
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan tyyppiin.
Hävitä käytetty paristo valmistajan ohjeiden mukaisesti.

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AUX COMPOSANTS RELATIFS ÀLA

SÉCURITÉ!
COMPONENTS IDENTIFIED BY A ! MARK ON THE SCHEMATIC
DIAGRAMS, EXPLODED VIEWS AND IN THE PARTS LIST ARE LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE ! SUR LES
CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO- SCHÉMAS DE PRINCIPE, LES VUES EXPLOSÉES ET LES
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR LISTES DE PIECES
AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB- SONT D'UNE IMPORTANCE CRITIQUE POUR LA SÉCURITÉ DU
LISHED BY SONY. FONCTIONNEMENT. NE LES REMPLACER QUE PAR DES
COMPOSANTS SONY DONT LE NUMÉRO DE PIÉCE EST
INDIQUÉ DANS LE PRÉSENT MANUEL OU DANS LES
SUPPLÉMENTS PUBLIÉS PAR SONY.

–6–
 CAUTION SAFETY CHECK-OUT
Use of controls or adjustments or performance of procedures After correcting the original service problem, perform the follow-
other than those specified herein may result in hazardous ra- ing safety check before releasing the set to the customer:
diation exposure. Check the antenna terminals, metal trim, “metallized” knobs,
screws, and all other exposed metal parts for AC leakage.
Check leakage as described below.

LEAKAGE TEST
This appliance is classified as a CLASS 1 LASER product. The AC leakage from any exposed metal part to earth ground and
The CLASS 1 LASER PRODUCT MARKING is located on from all exposed metal parts to any exposed metal part having a
the rear exterior. return to chassis, must not exceed 0.5 mA (500 microampers.).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’ instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
Laser component in this product is capable of emitting radiation VOM or battery-operated AC voltmeter. The “limit” indica-
exceeding the limit for Class 1. tion is 0.75 V, so analog meters must have an accurate low-
voltage scale. The Simpson 250 and Sanwa SH-63Trd are ex-
The following caution label is located inside the unit. amples of a passive VOM that is suitable. Nearly all battery
operated digital multimeters that have a 2 V AC range are suit-
able. (See Fig. A)

To Exposed Metal
Parts on Set

AC
0.15 µF 1.5 k Ω voltmeter
(0.75 V)

Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.

–7–
MODEL IDENTIFICATION HOW TO OPEN THE CD LID
— Bottom view —
1. Remove Side panel (L), (R). (Refer to page 12)
2. Rotate the Worm gear ass’y to direction of the arrow A.

CD lid

PART No.

Front Panel

Worm gear ass’y

MODEL PART No.
AEP and UK models 4-212-516-0π
Singapore and Hong Kong models 4-212-516-1π
US and Canadian models 4-212-516-3π
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK

1. Open the CD lid.

2. Turn on S104 and S916 as following figure.
3. Confirm that the laser diode emission while observing the ob-
jecting lens. When there is no emission, Auto Power Control
circuit or Optical Pick-up is broken.
Objective lens moves up and down once for the focus search.

Insert a precision
screwdriver and
push S916.

S104: ON

–8–
 SECTION 2
GENERAL
LOCATION OF CONTROLS
• Front view

1(Upper panel) 1 CD lid

2 6 (CD) button
2(Upper panel)
3 Display window
4 Remote sensor
5 MD ^ button and indicator
6 MD p button
3 7 VOLUME +/– buttons
4 8 6 (MD) button
9 5
9 CD p button
!º 6
0 CD ^ button and indicator
!¡ 7 !¡ 1/u button
!™ !™ FUNCTION button
8 !£ TUNER/BAND button
!£
!¢ PHONES jack
!∞ =0 button
!§ )+ button
!¶ MD disc slot
!• CD-MD SYNC button
!¢ !∞ !§ !¶ !• !ª !ª REC button and indicator

• Rear view

1 2 1 TAPE OUT jacks

2 TAPE IN jacks
3 SPEAKER terminals
4 VOLTAGE SELECTOR switch
(Singapore and Hong Kong models)
5 5 FM ANTENNA terminal
6 AM ANTENNA terminals
3
6

–9–
• REMOTE CONTROLLER

1 2 3 4 1 FUNCTION button
2 SLEEP button
3 CD, OPEN/CLOSE button
4 1/u button
5 MODE, PLAY/TUNING button
6 REPEAT, STEREO/MONO button
9 !º !¡ 5 7 VOL +/– buttons
!™ !£ !¢ 6 8 DBFB button
9 BAND, TUNER button
!∞ !§ !¶
0 –, PRESET button
!• !ª @º 7 !¡ +, PRESET button
@¡ @™ @£ !™ MD ( button
!£ MD P button
@¢ @∞ @§
!¢ MD p button
@¶ @• @ª 8 !∞ MD = button
!§ MD + button
!¶ MD SCROLL button
!• CD ( button
!ª CD P button
@º CD p button
@¡ CD = button
#º #¡ #™ #£
@™ CD + button
@£ DISPLAY, CHARACTER button
@¢ EDIT button
@∞ – button
@§ + button
@¶ SELECT, CLOCK/TIMER button
@• N, CURSOR button
@ª n, CURSOR button
#º SET, CLOCK/TIMER button
#¡ YES, ENTER button
#™ NO, CANCEL button
#£ MUSIC MENU button

– 10 –
 This section is extracted from
instruction manual.

– 11 –
 SECTION 3
DISASSEMBLY
Note: Follow the disassembly procedure in the numerical order given.

PANEL, COVER 1 two screws

(case 3 TP2) 5 two claws

2 two screws

6 rear cover

4 two claws

1 two screws 1 two screws

(case 3 TP2) (case 3 TP2)

3 side panel (L)

2 two screws

8 bottom cover
3 side panel (R)

7 six screws 1 two screws

(BVTT 3 × 6) (case 3 TP2)

2 two screws
(BVTP 3 × 8)
CD SECTION 4 CD section

1 Open the CD lid.

C 6 Remove the reinfocement (L)

to direction of arrow C – D.

8 connector
(CN902)

7 flat wire (19 core)

(CN102) D

A
3 two claws

2 three screws
(BVTP 3 × 8)

8 two connectors
(CN702, 707) B

5 Remove the reinfocement (R)

to direction of arrow A – B.

– 12 –
CD LID OPEN/CLOSE MOTOR

3 CD lid open/close
motor

2 two screws 1 belt

(B 2.6 × 3)

FRONT PANEL SECTION

1 connector
(CN104)

3 connector
(CN705)

4 front panel section

2 two screws
(BV/ring)

– 13 –
CD BASE UNIT

3 screw
(PTT 2.6 × 5)
5 two screws
(PTPWHM 2.6)

4 earth lug

5 two screws
(PTPWHM 2.6)

6 CD base unit
A

2 Remove the CD base unit

section to direction of
the arrow A.

1 two screws
1 two screws (BVTP 2.6)
(BVTP 2.6)

TUNER, MAIN BOARD

5 Remove the MAIN board

to direction of the arrow B.
3 flat wire (31 core)
(CN706)

B
3 flat wire (15 core)
(CN703)

4 two screws
(BVTP 3 × 8)

1 two screws
(BVTP 3 × 8)

3 flat wire (25 core)

(CN704)

2 Remove the tuner to

direction of the arrow A.

– 14 –
POWER BOARD 3 two screws
(BVTP 3 × 8)
5 connector
1 connector (CN503)
(CN501) 2 screw
(BVTT 3 × 6)

6 Remove the POWER board

to direction of the arrow A. A

1 connector
(CN501)

4 PC board holder

MD MECHANISM DECK 3 Remove the MD mechanism

deck section to direction
2 two screws
of the arrow A.
(BVTT 3 × 6)
2 two screws
(BVTT 3 × 6)
A

4 two screws
(BVTT 2 × 3)
4 two screws
(BVTT 2 × 3)

1 two screws
(BVTP 3 × 8)

5 MD mechanism deck

– 15 –
BD BOARD

1 flat wire (25 core)

(CN107)

5 BD (MD) board

3 screw
(BVTT 2 × 4)
2 flexible board
(CN104)

2 flexible board
(CN101)
1 flat wire (25 core)
(CN106)

4 two claws

SUB CHASSIS

1 two step screws 1 two step screws

2 insulator

2 insulator

part A
NG

part A
OK
part A
3 sub chassis

Take care so that the part A

may be right position when installing.

– 16 –
OVER WRITE HEAD

1 screw (P 1.7 × 6)

2 over write head

SHUTTER ASS’Y

1 stopper washer

2 shaft (shutter) A shutter ass’y

shaft (shutter) B

shaft (shutter) A
3 shutter ass’y
hole B

hole A

When installing, install the shaft (shutter) A

into the hole as show in the figune before
installing the shaft (shutter) B into the hole B.

– 17 –
SLIDER COMPLETE ASS’Y

claw
3 Set the shaft of gear (LB) to be at the
position in the figure.

claw

1 special screw
4 Remove the slider complete ass’y (M 1.7 × 1.4) 2 retainer (gear)
in the direction of arrow with putting
out of two claws.

NOTE FOR INSTALLATION

• SLIDER COMPLETE ASS’Y

slider ass’y

Install the part A of lever (head up)

to pass over the slider complete ass’y.

OK

part A

NG

Take care no to damage

the detective switch.

– 18 –
 SECTION 4
SERVICE MODE
Change-over of AM (MW) Tuner Step between 9 kHz and 10 kHz
• A step of AM (MW) channels can be changed over between 9 kHz and 10 kHz.

Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “TUNER”, and press [TUNER/BAND] button to select the BAND “AM (MW)”.
3. Press 1/u button to turn the set OFF.
4. Press [FUNCTION] and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “AM (MW) 9 kHz
STEP” or “AM (MW) 10 kHz STEP”, and thus the channel step is changed over.

Change-over of LW Tuner Step between 1 kHz and 3 kHz

• A step of LW channels can be changed over between 1 kHz and 3 kHz.

Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “TUNER”, and press [TUNER/BAND] button to select the BAND “LW”.
3. Press 1/u button to turn the set OFF.
4. Press [FUNCTION] and 1/u buttons simultaneously, and the display of fluorescent indicator tube changes to “LW 1 kHz STEP” or
“LW 3 kHz STEP”, and thus the channel step is changed over.

ATT Change-over of TAPE input

Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “TAPE”.
3. Press 1/u button to turn the set OFF.
4. Press 1/u button while pressing [FUNCTION] button. The power is turned on and the display of fluorescent indicator tube changes
to “Attenuator ON” or “Attenuator OFF”, then ATT change-over of TAPE input is completed.

CD tracking balance display

Procedure:
1. Press 1/u button to turn the set ON.
2. Select the function “CD”.
3. Press [TUNER/BAND] button while pressing p (CD) button.
4. The display of fluorescent indicator tube shows you the following message.
CD TR. BAL. ππ

LED and Fluorescent Indicator Tube All Lit, Key Check Mode

Procedure:
1. Press two buttons [VOLUME–] and [TUNER/BAND] simultaneously.
2. LEDs and fluorescent indicator tube are all turned on.
3. When the [FUNCTION] button is pressed, the fluorescent indicator tube lights up in the order of; partial lighting 1 n partial lighting
2 n all lit n partial lighting 1 n.
When the [VOLUME+/–] button is pressed, the LED lighting pattern changes.
To end without switching to the key check mode, press the 1/u button to turn off the power.
4. Press p (CD) button, and the key check mode is activated.
5. In the key check mode, the fluorescent indicator tube displays “KEY=0 JOG=0”. Each time a button is pressed, “KEY=” value
increases. However, once a button is pressed, it is no longer taken into account.
“JOG=” Value increases like 1, 2, 3 ... if press [VOLUME+] button, or it decreases like 99, 98, 97 ... if press [VOLUME–] button.
6. To exit from this mode, press order all buttons (13 buttons), and press any button, or disconnect the power cord.

SUB CLOCK CHECK

Procedure:
1. Connect an oscilloscope to IC707 pin (¡ and ground of the MAIN board.
2. Press two buttons [VOLUME–] and [REC] simultaneously, and the fluorescent indicator tube displays “32.768 kHz (91)”.
3. To check the signal on oscilloscope becomes 32 kHz square wave.
4. Press 1/u button to exit.

– 19 –
 SECTION 5
TEST MODE
5-1. PRECAUTIONS FOR USE OF TEST MODE

Recording Laser Emission Mode

• Continuous recording mode (CREC MODE)
• Traverse adjustment mode (EFBAL ADJUST)
• Laser power adjustment mode (LDPWR ADJUST)
• Laser power check mode (LDPWR CHECK)
• Traverse (MO) check (EF MO CHECK)
• Traverse (MO) adjustment (EF MO ADJUST)

5-2. SETTING THE TEST MODE

With the power off, press the =0 button while pressing the [VOLUME–] button.

5-3. EXITING THE TEST MODE

Press the p (MD) button while pressing the [FUNCTION] button. The STANDBY state will be set and the test mode will be cleared.

5-4. BASIC OPERATIONS OF THE TEST MODE

All operations are performed using the [VOLUME+/–] button, p (CD) button, and ^ (CD) button.
The functions of these buttons are as follows.

Function name Function

VOLUME +/– button Changes parameters and modes
p (CD) button Proceeds onto the next step. Finalizes input.
^ (CD) button Returns to previous step. Stops operations.

– 20 –
5-5. SELECTING THE TEST MODE
There are altogether 26 test modes, shown in the following table. Press the [VOLUME+] button to the mode below the current mode in the
table while press the [VOLUME–] button to the mode above. Each time the ^ (CD) button is pressed, the display changes in the
following order;
“TEMP CHECK” n “TEMP ADJUST” n “SLED MOVE” n “CPLAY 2 MODE” n “TEMP CHECK”…

Display Contents Mark

TEMP CHECK Temperature compensation offset check
LDPWR CHECK Laser power check
EF MO CHECK Traverse (MO) check
EF CD CHECK Traverse (CD) check
FBIAS CHECK Focus bias check
CPLAY MODE Continuous playback mode
CREC MODE Continuous recording mode
Scurve CHECK S curve check (X)
VERIFY MODE Non-volatile memory check (X)
DETRK CHECK Detrack check (X)
TEMP ADJUST Temperature compensation offset adjustment
LDPWR ADJUST Laser power adjustment
EF MO ADJUST Traverse (MO) adjustment
EF CD ADJUST Traverse (CD) adjustment
FBIAS ADJUST Focus bias adjustment
EEP MODE Nonvolatile memory control (X) (!)
MANUAL CMD Command transfer (X)
SVDATA READ Status display (X)
ERR DP MODE Error history display, clear
SLED MOVE Sled check (X)
ACCESS MODE Access check (X)
0920 CHECK Outermost circumference check (X)
WRITE sure? Non-volatile memory Initialize (X) (!)
HEAD ADJUST Head position check (X)
CPLAY2 MODE Continuous playback mode (X)
CREC2 MODE Continuous recording mode (X)

• For details of each adjustment mode, refer to the items in “6. Electrical Adjustments”. For details of “ERR DP MODE”, refer to the self-
diagnosis function on page 2.
• If other modes are set accidentally, press the ^ (CD) button to exit that mode.
• As items marked (X) in the “Mark” column are not used during servicing, they are not described here. If these modes are set acciden-
tally, press the ^ (CD) button to exit the mode. Be especially careful with items marked (!) as they will overwrite the non-volatile
memory, and as a result, the unit will not operate normally.

5-5-1. Operating the Continuous Playback Mode

1. Entering the continuous playback mode
1 Set the disc in the unit. (Recordable discs or discs for playback only.)
2 Press the [VOLUME+/–] button and display “CPLAY MODE”.
3 Press the p (CD) button to change the display to “CPLAY MID”.
4 When access completes, the display changes to “C = AD = ”.
Note: The numbers “ ” displayed indicate the error rates and “ADER”.

2. Changing the part to be played back

1 When the p (CD) button is pressed during continuous playback, the display changes as below, and the played back part can be
changed.
“CPLAY MID” n “CPLAY OUT” n “CPLAY IN”

2 When access completes, the display changes to “C = AD = ”.

Note: The numbers “ ” displayed indicate the error rate and “ADER”.

– 21 –
3. Ending the continuous playback mode
1 Press the ^ (CD) button. The display changes to “CPLAY MODE”.
2 Press the 6 (MD) button to remove the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows. To display the playback position address on the display, press the 1/u
button to display “CPLAY ( )”.
IN: 40h cluster
MID: 300h cluster
OUT: 700h cluster

5-5-2. Operating the Continuous Recording Mode

1. Entering the continuous recording mode
1 Set a recordable disc in the unit. (Refer to Note 3.)
2 Press the [VOLUME+/–] button and display “CREC MODE”.
3 Press the p (CD) button to change the display to “CREC MID”.
4 When access completes, the display changes to “CREC ( )” and the REC display lights up.
Note: The numbers “ ” displayed indicate the recording position address.

2. Changing the part to be recorded

1 When the p (CD) button is pressed during continuous recording, the display changes as below and the recorded part can be
changed. The REC display is off while changing.
“CPLAY MID” n “CPLAY OUT” n “CPLAY IN”

2 When access completes, the display changes to “CREC ( )” and the REC display lights up.
Note: The numbers “ ” displayed indicate the recording position address.

3. Ending the continuous recording mode

1 Press the ^ (CD) button. The display changes to “CREC MODE”, and the REC goes off.
2 Press the 6 (MD) button to remove the disc.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN: 40h cluster
MID: 300h cluster
OUT: 700h cluster
Note 2: The ^ (CD) button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.

5-5-3. Non-Volatile Memory Mode (EEP MODE)

This mode reads and writes the contents of the non-volatile memory.
It is not used in servicing. If set accidentally, press the ^ (CD) button immediately to exit it.

5-6. FUNCTIONS OF OTHER BUTTONS

Function Contents
(P (MD) Sets continuous playback when pressed in the STOP state. Turns ON/OFF the tracking servo when pressed
during continuous playback.
p (MD) Stops the continuous playback and recording.
)+ Moves the sled to the external circumference only while the button is pressed.
=0 Moves the sled to the internal circumference only while the button is pressed.
CD-MD SYNC Switches between pit and groove when pressed.
1/u Switches the displayed contents when pressed.
6 (MD) Ejects the disc.

– 22 –
5-7. DISPLAYS DURING TEST MODE
The display changes according to the following sequence each time the 1/u button is pressed.

1. Mode display
“TEMP ADJUST” and “CPLAYMODE” are displayed.
Mode display
2. Error rate display
The error rate is displayed as follows. Error rate display
C= AD =
C = :Indicates the C1 error. Address display
AD = :Indicates ADER.
Auto gain display (Not used in servicing)
3. Address display
The address is displayed as follows. (MO: Recordable disc, CD: Disc for palyback only) Detrack check display (Not used in servicing)
When the [CD-MD SYNC] button is pressed, the display will switch between groove
and pit. IVR display (Not used in servicing)
h= s= (MO pit and CD)
h= a= (MO groove)
h = Indicates the header address.
s = Indicates the SUBQ address.
a = Indicates the ADIP address.

Note: Displayed as “–” when servo is operated.

4. Auto gain display (Not used in servicing)

The auto gain is displayed as follows.
AG = / [ ]

5. Detrack check display (Not used in servicing)

The detrack is displayed as follows.
ADR =

6. IVR display (Not used in servicing)

IVR is displayed as follows.
[ ][ ][

Meanings of other displays

Contents
Display
When Lit When Off
REC Recording mode ON Recording mode OFF
ATT ABCD adjustment completed
SHUFFLE Focus auto gain OK
TRACK Pit Groove
DISC High reflection rate Low reflection
LEVEL-SYNC CLV-S CLV-A
SYNC CLV LOCK CLV UNLOCK

– 23 –
5-8. AGING MODE
This unit is provided with an aging mode.
In this mode, MD and CD operations are performed alternately according to the following sequence.
Aging will be carried out continuously unless an error occurs.
If an error occurs, the status and number of cycles are displayed alternately, and operations stop. (Refer to Table 1.)

Aging Mode Sequence

Start

Turn ON Power using function MD

Cannot read
MD TOC READ Message 6

Can read
Above 20
MD all erase MD last track
Less than 20
NO
Blank disc
Message 1
YES
CD function is set and CD TOC is read

NO
CD TOC OK? Message 7

YES
CD synchro standby

NO
OK? Message 2 or 8
YES
CD last track search pause state

NO
OK? Message 9
YES
CD synchro starts

NO
OK? Message 3 or 0
YES

Synchro ends?

OK
Playing CD?
MD function is set
NG
CD tray opens Message !º

NO
OK? Message !¡
YES
CD tray closes

NO
OK? Message !™
YES
MD last track (for 3 sec.) play

NO
OK? Message 4
YES
Power goes off and MD TOC is written

Aging cycle number is displayed

Power turns ON and MD TOC is read

NO
OK? Message 5 or Message 6
YES

– 24 –
Procedure:
1. Load a recordable disc (MD) and CD test disc (YEDS-18). (*Note 1)
2. While pressing the [VOLUME–] button, press the )+ button.
3. Aging is executed in the above sequence.
4. To end, press the p (CD or MD) button.
*Note 1: Any CD can be used, but one with a short last track is recommended. The time of one aging cycle will be longer if the last track is long.
Also use a CD in which the length of the last track x 20 does not exceed the recording time of the recording MD.

Table 1. Messages and Main Causes When Aging Stops

No. Error Messages Details of Error Main Causes

1 MD A Erase NG Cannot MD all erase. A disc for playback only was used. The rec-proof tab is set to
protect. Disc error, etc.
2 MD R-Pause NG Cannot set MD Rec Pause. Disc is full, etc.
3 MD D-input NG Cannot lock MD digital in.
4 MD Play NG Cannot play last track. Access error, etc.
5 MD TOC NG MD TOC are different. No. of total tracks does not match logic value.
6 MD No Disc NG Cannot read MD TOC. Disc error, etc.
7 CD No Disc NG Cannot read CD TOC. Optical defect, spindle defect (including motor), cannot read Q
data, disc defect (scratches, etc.), bad focus, bad GFS, etc.
8 CD Pause NG Cannot set CD pause in Disc defect (scratches, etc.), cannot read Q data, etc.
CD synchro mode.
9 CD Search NG Cannot search last track on CD. Optical defect, sled, tracking defect (including motor), cannot
read Q data, disc defect (scratches, etc.).
0 CD Play NG Cannot play last track on CD. Optical defect, cannot read Q data, disc defect (scratches, etc.),
etc.
!¡ CD Open NG Cannot open CD tray. LOAD OUT SW defect
!™ CD Close NG Cannot close CD tray. LOAD IN SW defect

– 25 –
 SECTION 6
ELECTRICAL ADJUSTMENTS
Note: When performing laser power checks and adjustment (electrical
MD SECTION adjustment), use of the new MD laser power meter 8010S (J-2501-
145-A) instead of the conventional laser power meter is convenient.
6-1. PRECAUTIONS FOR CHECKING LASER It sharply reduces the time and trouble to set the laser power meter
DIODE EMISSINON sensor onto the objective lens of the pick-up.
When checking the emission of the laser diode during adjustments,
never view directly from the top as this may cause blindness. 6-4. CREATING THE CONTINUOUSLY
RECORDED DISC
6-2. PRECAUTIONS FOR USE OF OPTICAL • The disc is used for the focus bias adjustment and error rate
PICK-UP (KMS-260A) check.
As the laser diode in the optical pick-up is easily damaged by static The following describes how to create a continuously recorded
electricity, solder the laser tap of the flexible board when using it. disc.
Before disconnecting the connector, solder first. Before connect- 1. Insert a disc (blank disc) commercially available.
ing the connector, be careful not to remove the solder. Also take 2. Press the [VOLUME+/–] button to display “CREC MODE”.
adequate measures to prevent damage by static electricity. Handle 3. Press the p (CD) button to display “CREC MID”.
the flexible board with care as it breaks easily. “CREC (0300)” will be momentarily displayed and recording
pick-up flexible board
started.
4. Complete recording within 5 minutes.
5. Press the ^ (CD) button and stop recording .
6. Press the 6 (MD) button and remove the disc.

Create the continuous recorded disc for adjusting the focus bias
and checking the error rate as described above.
Note:
• Be careful not to apply vibrations during continuous recording.

6-5. TEMPERATURE COMPENSATION OFFSET

laser tap ADJUSTMENT
Optical pick-up flexible board Save the current temperature data in the non-volatile memory as
the 25 °C standard data.
6-3. PRECAUTIONS FOR ADJUSTMENTS Notes:
1) When replacing the following parts, perform adjustments and 1. Normally, this adjustment should not be preformed.
checks marked ¬ in the order shown in the following table. 2. Set the surrounding temperature to 22 to 28 °C when performing this
adjustment.
Optical BD (MD) Board Also perform this adjustment immediately after the power is turned
Pick-up IC171 D101 IC101, IC121, IC192 on when the internal temperature of the unit is the same as the sur-
rounding temperature (22 to 28 °C).
1. Temperature 3. After replacing D101, perform this adjustment after the temperature
compensation G ¬ ¬ ¬ of parts reach the surrounding temperature.
offset adjustment
Adjusting Procedure:
2. Laser power \
¬ ¬ G ¬ 1. Press the [VOLUME+/–] button, to display “TEMP ADJUST”.
adjustment 2. Press the p (CD) button and select the “TEMP ADJUST”
3. Traverse mode.
¬ ¬ G ¬
adjustment 3. “TEMP= ” and the current temperature data are displayed.
4. Focus bias 4. To save the data: Press the p (CD) button.
¬ ¬ G ¬ If not saving the data: Press the ^ (CD) button.
adjustment
5. When the p (CD) button is pressed, “TEMP= SAVE” is
5. Error rate check ¬ ¬ G ¬ displayed, and then “TEMP ADJUST” is displayed again.
“TEMP ADJUST” is displayed again immediately after the
^ (CD) button is pressed.
2) Perform the adjustment in the test mode.
After completing the adjustments, exit the test mode. Specifications:
3) Perform the adjustments in the order shown. TEMP= should be E0 to EF. F0 to FF, 00 to 0F, 10 to 1F and 20
4) Use the following tools and measuring devices. to 2F.
• Check disc (MD) TDYS-1
(Parts No. 4-963-646-01)
• Laser power meter LPM-8001 (Parts No. J-2501-046-A)
or
MD Laser power meter 8010S (Parts No. J-2501-145-A)
• Oscilloscope (Measure after calibration of the probe).
• Digital voltmeter
• Thermometer
5) When observing several signals on the oscilloscope, etc., make
sure that VC and ground do not connect inside the oscilloscope.
(The VC and ground will short-circuit.)

– 26 –
6-6. LASER POWER ADJUSTMENT 6-7. TRAVERSE ADJUSTMENT

Connection : Laser power Connection :

Oscilloscope
meter

BD (MD) board
TP69 (TEO)
Optical pick-up TP1003 (VC)
objective lens
V: 0.5 v/div H: 10 ms/div
Input: DC mode
Digital volt meter
Adjusting Procedure:
1. Connect an oscilloscope to TP69 (TEO) and TP1003 (VC) of
BD (MD) board the BD (MD) board.
TP (I+3V) 2. Load a recordable disc (any available on the market). (Refer
TP (IOP)
to Note 1.)
3. Press the =0 or )+ button to move the optical
Adjusting Procedure: pick-up outside the pit.
1. Set the laser power meter on the objective lens of the optical pick- 4. Press the [VOLUME+/–] button to display “EFBAL ADJUST”.
up from the disc slot. (If it cannot be set properly, press the 5. Press the p (CD) button to display “EFB = MO-R”.
=0 or )+ button to move the optical pick-up). (Laser power READ power/Focus servo ON/tracking servo
Connect the digital voltmeter to TP (I+3V) and TP (IOP) of OFF/spindle (S) servo ON)
the BD (MD) board. 6. Press the [VOLUME+/–] button so that the oscilloscope wave-
2. Press the [VOLUME+/–] button to display “LDPWR ADJUST”. form becomes the specified value. (Press the [VOLUME+/–]
(Laser power: For adjustment) button changes the “EFB= ” value and the waveform.) The
3. Press the p (CD) button once to display “LD 0.9 mW $ ”. waveform changes by about 2% everytime when adjusted.
4. Press the [VOLUME+/–] button so that the laser power meter Adjust as close as possible to the specified value.
reads 0.86 to 0.92 mW. Set the range knob of the laser power (Read power traverse adjustment)
meter to 10 mW, press the p (CD) button, and save the ad-
justment results in the non-volatile memory. (“LD SAVE $ (Traverse Waveform)
” is displayed momentarily.)
5. “LD 7.0 mW $ ” is next displayed.
A
6. Press the [VOLUME+/–] button so that the laser power meter
reads 6.9 to 7.1 mW, press the p (CD) button, and save the VC
adjustment results in the non-volatile memory. (“LD SAVE $ B
” is displayed momentarily.)
Note: Do not emit 7.0 mW continuously for more than 15 seconds.
7. Press the [VOLUME+/–] button to display “LDPWR CHECK”. Specified value : A = B
8. Press the p (CD) button once to display “LD 0.9 mW $ ”.
Check that the laser power meter reading is 0.85 to 0.91 mW. 7. Press the p (CD) button and save the adjustment results in
9. Press the p (CD) button another time to diaplay “LD 7.0 the non-volatile memory (displayed as “EFB = SAVE”
mW $ ”. momentarliy and then displayed as “EFB = MO-W”).
Check that the readings of the laser power meter and digital 8. Press the [VOLUME+/–] button so that the oscilloscope wave-
voltmeter become the specified value. form becomes the specified value.
(Pressing the [VOLUME+/–] button changes the “EFB= ”
Specified Value : value and the waveform.) The waveform changes by about 2%
Laser power meter reading : 7.0 ± 0.1 mW everytime when adjusted. Adjust as close as possible to the
Digital voltmeter reading : Value displayed on optical pick-up la- specified value.
bel ± 10% (Write Power Traverse Adjustment)

(Optical pick-up label) (Traverse Waveform)

KMS
260A
27X40 A
B0825
VC
N

Iop = 82.5 mA in this case B

Iop (mA) = Digital voltmeter reading (mV)/1 (Ω)

10. Press the ^ (CD) button to display “LDPWR CHECK” and Specified value : A = B
stop the laser emission.
(The ^ (CD) button is effective at all times to stop the laser 9. Press the p (CD) button to save the adjustment results in the
emission.) non-volatile memory (displayed as “EFB = SAVE”
momentarliy).

– 27 –
10. Next “EFB = MO-P” is displaed, the optical pick-up moves 6-8. FOCUS BIAS ADJUSTMENT
to the internal circumference of the pit and servo is imposed. Adjusting Procedure :
11. Press the [VOLUME+/–] button so that the oscilloscope wave- 1. Load a continuously recorded disc (Refer to 6-4. Creating the
form becomes the specified value. Continuously Recorded Disc”).
The waveform changes by about 2% everytime when adjusted. 2. Press the [VOLUME+/–] button and display “CPLAY MODE”.
Adjust as close as possible to the specified value. 3. Press the p (CD) button to display “CPLAY MID”.
4. When “C = AD = ” is displayed, press the ^ (CD)
(Traverse Waveform) button.
5. Press the [VOLUME+/–] button to display “FBIAS ADJUST”.
6. Press the p (CD) button to display “ / a = ”.
A
The first four digits indicate the C1 error rate, the two digits
VC after the “/” indicate ADER and the two digits after “a =” indi-
B cate the focus bias value.
7. Press the [VOLUME+/–] button, and look for the focus bias
value at which the C1 error rate becomes approximately about
Specified value : A = B 200. (Refer to Note 2).
8. Press the p (CD) button to display “ / b = ”.
12. Press the p (CD) button and save the adjustment results in
9. Press the [VOLUME+/–] button, and look for the focus bias
the non-volatile memory (displayed as “EFB = SAVE”
value at which the C1 error rate becomes about 200.
momentarliy).
The C1 error rate at this time should be almost same as the
“EFBAL: CD is next displayed and the disc stops rotating au-
value set in step 7.
tomatically.
10. Press the p (CD) button to display “ / c = ”.
13. Press the 6 (MD) button and remove the disc.
11. Check that the C1 error rate is below 50 and that ADER is 00.
14. Load the check disc (MD) TDYS-1.
and press the p (CD) button.
15. Press the p (CD) button to display “EFB = CD”. The
12. If the value of “( )” in the “ - - ( )” displayed is
servo is imposed automatically.
above 20, press the p (CD) button.
16. Press the [VOLUME+/–] button so that the oscilloscope wave-
If below, press the ^ (CD) button and start from step 2
form becomes the specified value.
again.
The waveform changes by about 2% everytime when adjusted.
13. Press the 6 (MD) button and remove the continuously re-
Adjust as close as possible to the specified value.
corded disc.
Note 1: The following figure shows the relation between the C1 error
(Traverse Waveform) and focus bias value. Look for points a and b in the following
figure by the adjustment avove. The focus position (point c) is
A automatically calculated from points a and b.
Note 2: As the C1 error rate changes, use the average value in the ad-
VC justment.
B
C1 error

Specified value : A = B about

200
17. Press the p (CD) button and save the adjustment results in
the non-volatile memory after “EFB = SAVE” is
momentarliy displayed.
Focus bias value
“EFBAL ADJUST” is next displayed. (F. BIAS)
18. Press the 6 (MD) button and remove the check disc (MD)
b c a
TDYS-1.

Note 1: The data will be overwritten on the MO and erased when a re-
corded disc is used in this adjustment.
Note 2: If the traverse waveform is not clear, connect the oscilloscope as
shown in the following figure so that it can be seen more clearly.

Oscilloscope

BD (MD) board 330 k Ω

TP69 (TEO)
TP1003 (VC)
10 pF

– 28 –
6-9. ERROR RATE CHECK
6-9-1. CD Error Rate Check

Checking Procedure :
1. Load a check disc (MD) TDYS-1.
2. Press the [VOLUME+/–] button to display “CPLAY MODE”.
3. Press the p (CD) button to display “CPLAY MID”.
4. “C = AD = ” is displayed.
5. Check that the C1 error rate is below 20.
6. Press the ^ (CD) button to stop playback. Then press the
6 (MD) button, and remove the check disc (MD).

6-9-2. MO Error Rate Checking

Checking Procedure :
1. Load a continuously recorded disc (Refer to 6-4. Creating the
Continuously Recorded Disc”).
2. Press the [VOLUME+/–] button to display “CPLAY MODE”.
3. Press the p (CD) button to display “CPLAY MID”.
4. “C = AD = ” is displayed.
5. Check that the C1 error rate is below 50 and ADER is 00.
6. Press the ^ (CD) button to stop playback. Then press the
6 (MD) button, and remove the disc.

6-10. FOCUS BIAS CHECK

Change the focus bias value and check the focus tolerance amount.

Checking Procedure :
1. Load a continuously recorded disc (Refer to 6-4. Creating the
Continuously Recorded Disc”).
2. Press the [VOLUME+/–] button to display “CPLAY MODE”.
3. Press the p (CD) button to display “CPLAY MID”.
4. When “C = AD = ” is displayed, press the ^ (CD)
button.
5. Press the [VOLUME+/–] button to display “FBIAS CHECK”.
6. Press the p (CD) button to display “ / c = ”.
The first four digits indicate the C1 error, the two digits after
the “/” indicate ADER and the two digits after “c =” indicate
the focus bias value.
Check that the C1 error is below 50 and ADER is 00.
7. Press the p (CD) button to change the display to “ / b
= ”.
Check that the C1 error does not drop below about 200 and
ADER does not remain above 00.
8. Press the p (CD) button to change the display to “ / a
= ”.
Check that the C1 error does not drop below about 200 and
ADER does not remain above 00.
9. Press the ^ (CD) button, press the 6 (MD) button next,
and remove the continuously recorded disc.

Note 1: If the C1 error is above about 200 or ADER is above 00 only for
point a (step 8 above) and point b (step 7 above), the focus bias
may not adjusted properly. In this case, adjust again.

– 29 –
6-11. ADJUSTING POINTS AND CONNECTING POINTS

[BD (MD) Board] (Side A)

D101

IC192

[BD (MD) Board] (Side B)

TP (IOP) TP (I + 3V)

Q163

IC316 IC171

TP1003
(VC)

TP69 IC101
(TEO)
Q102

IC121

– 30 –
 S Curve Check
CD SECTION
oscilloscope
Note: BD (CD) board
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given. TP (FEO) +
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated. TP (VC) –
3. Use an oscilloscope with more than 10 MΩ impedance.
4. Clean the object lens by an applicator with lens cleaning liq-
uid when the signal level is low than specified value with the Procedure :
following checks. 1. Connect oscilloscope to test point TP (FEO).
5. Adjust the focus bias adjustment when optical block is replaced. 2. Connect between test point TP (FOK) and Ground by lead
wire.
Focus Bias Adjustment 3. Turn Power switch on.
Perform this adjustment when the optical pick-up has been re- 4. Put disc (YEDS-18) in and turned Power switch on again and
placed or repaired. actuate the focus search. (actuate the focus search when disc
table is moving in and out.)
oscilloscope 5. Check the oscilloscope waveform (S-curve) is symmetrical be-
BD (CD) board tween A and B. And confirm peak to peak level within 2.4 ±
0.7 Vp-p.
TP (RF) +
TP (VC) –
S-curve waveform
symmetry
Procedure:
1. Connect oscilloscope to test point TP (RF).
A
2. Turn Power switch on.
3. Put disc (YEDS-18) in and playback. within 2.4 ± 0.7 Vp-p
4. Adjust RV101 so that the waveform is clear. B
(Clear RF signal waveform means that the shape “≈” can be
clearly distinguished at the center of the waveform.)
5. After adjustment, check the RF signal level. 6. After check, remove the lead wire connected in step 2.
Note: • Try to measure several times to make sure than the ratio of A : B
• RF signal or B : A is more than 10 : 7.
VOLT/DIV: 200 mV • Take sweep time as long as possible and light up the brightness to
TIME/DIV: 500 nS obtain best waveform.

RF Level Check
oscilloscope
BD (CD) board
level : 1.3 ± 0.3 Vp-p
TP (RF) +
TP (VC) –

Procedure :
1. Connect oscilloscope to test point TP (RF) on BD (CD) board.
2. Turn Power switch on.
3. Put disc (YEDS-18) in and playback.
4. Confirm that oscilloscope waveform is clear and check RF
signal level is correct or not.
Note: Clear RF signal waveform means that the shape “≈” can be clearly
distinguished at the center of the waveform.

RF signal waveform
VOLT/DIV : 200 mV
TIME/DIV : 500 nS

level : 1.3 ± 0.3 Vp-p

– 31 –
E-F Balance (1 Track Jump) Check Adjustment Location:
(Without remote commander)
[BD (CD) Board] (Side B)
oscilloscope
BD (CD) board RF
FOK
TP (TEO) +
TP (VC) – RV101
(Focus Bias

IC102
Adjustment) IC101
TEI
Procedure : RV103
1. Connect oscilloscpe to test point TP (TEO) on BD (CD) board. FEO
2. Turn Power switch on. TEO FEI
3. Put disc (YEDS-18) in to play the number five track. RV102
4. Press the “ ^ (CD) (Pause)” button. (Becomes the 1 track VC
jump mode)
5. Confirm that the oscilloscope waveform is symmetrical on the
top and bottom in relation to 0Vdc, and check this level. (Focus/Tracking Gain Adjustment)

1 track jump waveform

IC104
PCK
A
0V GND
B

LEVEL : 300 ± 100 mVp-p

A–B
Specified level: • x 100 = less than ± 7%
2 (A + B)
• A + B = 300 ± 100 mVp-p

6. Remove the lead wire connected in step 1.

Focus/Tracking Gain Adjustment (RV102, RV103)

This gain has a margin, so even if it is slightly off.

There is no problem.
Therfore, do not perform this adjustment.
Please note that it should be fixed to mechanical center position
when you moved and do not know original position.

– 32 –
 HCD-MD1EX
SECTION 7
DIAGRAMS
7-1. BLOCK DIAGRAM – CD Section –
DIGITAL FILTER,
D/A CONVERTER,
RF AMP, FILTER LOW-PASS FILTER
FOCUS/TRACKING/SLED SERVO IC104
IC101 DIGITAL SIGNAL
PROCESSOR, CLV SERVO
IC103 CLOCK XTAI XTI 5
RF AMP 7 12 9 8 34 4 CKO
GENERATOR X101

CLTV
A PD1

FILO

PCO
16.9344MHz

FILI
4 35
PCMD XTO 6
RF 21 2 DATA
DETECTOR RFO RF ASYMMETRY EFM D/A BCLK
+ SUMMING 31 14 DIGITAL PLL 22 3 BCLK
RF AMP CORRECTION DEMODULATOR INTER- LRCK CD-L
A D AMP FACE 20 1 LRCK LOUT 16 A
D PD2 RFI
5 36 30 (Page 37)

INTERNAL BUS
C ROUT 13 R-CH
1
B C
I-V AMP

16k
B
2 FOCUS OK FOK FOK RAM

MLAT
DATA
CLOK
25 1
COMPARATOR
FE BIAS FOCUS OK
37
AMP SUB-CODE ERROR 26 27 28
RV101 PROCESSOR CORRECTOR
DATA DATO

SERVO AUTO
F MIRR

SEQUENCER
FOCUS BIAS 21 56

DATA
F

CLK
LAT
10 AMP TTL TTL CLK CLKO
19 59

I2L DATA REGISTER

E XLT XLTO
E 20 57 DIGITAL
6 DEFECT IIL IIL XRST
22 OUT
AMP
DOUT DOUT
SENS SEIN
39 B
IIL 24 54 (Page 36)
C.OUT CNIN
TTL 23 55
WFCK
41
GFS
27
OPTICAL PICK-UP
(KSS-213B/K-N) FOCUS 50 XRST DIGITAL CPU
FEO FEI FOCUS PHASE FEO CLV INTERFACE
ERROR 1 2 6 FOCUS
COMPENSATION SWITCH
AMP

SQSO

SCOR

SPOD
XLON

SQCK

SBSO
Q103

SENS
DATA
CLOK
XLAT
MON
MDP
MDS
RV102 FGD
4
FOCUS GAIN
2 3 4 64 46 47 49 51 53 52 43 44 63

S101
F (LIMIT)
38 TRACKING TEO TEI
I-V TRACKING PHASE TAO ON: When the optical pick-up is
E ERROR 42 44 13
LASER DIODE 39 AMP COMPENSATION inner position.
AMP
RV103
AUTOMATIC TRACKING DATA
LD LD PD
POWER CONTROL 33 GAIN CLK
AMP AMP
PD LD Q101, 102 PD
SLO SLED SL+
34 16 14

LAT
AMP

FOCUS/TRACKING COIL DRIVE,

SPINDLE/SLED MOTOR DRIVE
IC102
46 48 53 50 49 51 22 52
2-AXIS IC102 (1/2)

PRGL (DF-LAT)
SUBQ
SQCLK
SENSE
DATA
CLOCK
XLT
SCOR
DEVICE TRK+ OUT3B 59 FOCUS-SW
18 TRACKING IN3A
(TRACKING)

OUT3A 19
COIL DRIVE
(FOCUS)

17 60 BD-REST
MASTER CONTROLLER
(CD MECHANISM CONTROL)

LOAD-OUT
TRK– IC707 (1/3)

LOAD-IN
OUT-SW
OUT2B

IN-SW
FCS+ OP+
11 FOCUS IN2B OPOUT + 16
FCS– OUT2A 9 14
12 COIL DRIVE –
55 56 58 57
IC102 (2/2)

OUT4A
M102 27 SLED MOTOR IN4A
(SLED)
M 26
OUT4B 25
DRIVE S916
05 (CD LID OPEN/CLOSE DETECT) 6 5
(ON: CD lid is closed.)

IN1
IN2
CD LID OPEN/CLOSE
MOTOR DRIVE

OUT2

OUT1
OUT1A IC702
M101 1 SPINDLE IN1B
(SPINDLE)
M 2
OUT1B
MOTOR DRIVE
4
S104 10 2
XRST 7 (DISC DETECT)

M • SIGNAL PATH
DISC IN DISC OUT : CD PLAY (ANALOG OUT)
M103
(CD LID OPEN/CLOSE)
: CD PLAY (DIGITAL OUT)

– 33 – – 34 –
HCD-MD1EX

7-2. BLOCK DIAGRAM – MD Section – DIGITAL SIGNAL PROCESSOR,

EFM/ACIRC ENCODER/DECODER, 15
SHOCK PROOF MEMORY CONTROLLER, IC121 (1/2) TX
ATRAC ENCODER/DECODER, 2M BIT D-RAM (Page 37)
OVER WRITE IC121 (1/2) EFMO ADDT ADDT
HEAD DRIVE 100 23 C
IC181, Q181, 182
HR901
OVER WRITE HEAD FILI
59
PCO

FILTER
58
CLTV PLL

MEMORY CONTROLLER
61 SAMPLING

ENCODER/DECODER

ENCODER/DECODER
FILO

SHOCK PROOF
60 RATE

EFM/ACIRC
CONVERTER

ATRAC
RF AMP,
FOCUS/TRACKING ERROR AMP
IC101 DIGITAL DIN WAVE SHAPER DOUT
48 47
ASYO AUDIO DOUT
21
IC401 B
51 INTERFACE 22 (Page 34)

MORFO
MORFI
ASYI
I I 52 COMPA- DADT DADT, BCK, LRCK, FS256
1
RF AMP
RFO
46 40
AGCI RF AGC RF
38 55
RFI RATOR
24 D
J J & EQ
2 (Page 37)

EQ 26 25 27
AUX

XBCK
LRCK
FS256
B.P.F.
33
WBL D-RAM OSCI
3T CLOCK 16
F TEMP PEAK OSCO X101
PEAK & 37 GENERATOR 17
B BOTM 22.5792MHz
BOTTOM 36
WBL

D0 – D3
C B SUBCODE

ADFG
INTERNAL BUS
I J ADFM ADIN ADIP PROCESSOR

47, 46, 48, 49

D A AT ADFG

1, 2, 18, 19
DQ1 – DQ4
B.P.F. 29 30 32 78 DEMODULATOR/
A A AMP
4 DECODER
B
5 I-V ABCD
E C ABCD
6 AMP 35
DETECTOR D AMP
CPU MONITOR D-RAM

A00 – A09
7 FE
C FOCUS F0CNT SPINDLE INTERFACE CONTROL IC124

32 – 29, 34 – 38, 43
34 79
ERROR AMP

6 – 9, 11 – 15, 5
D SERVO

A0 – A9
SWDT
TE

MNT0
MNT1
MNT2
MNT3
SPRD

DQSY
E

SQSY

SRDT
E

SENS
SPFD

SCLK
XLAT
XINT
XRST
8 I-V TRACKING 26
F F SE
9 AMP ERROR AMP 28
LASER DIODE 94 93 10 12 11 14 9 8 5 6 7 1 2 3 4
COMMAND
WBL

SHOCK
AUTOMATIC

XBUSY
SLOCK
EQ
3T

FOK
ILCC APC LD/PD XOE
POWER 41 16 XOE
11 XWE
CONTROL AMP 45 3 XWE
Q162, 163 SERIAL/
PD LD XRAS
PARALLEL 44 4 XRAS
V-I CONVERTER, XCAS
42 17 XCAS
CONVERTER DECODER
PD LASER ON
PD
APCREF

F0CNT

SWITCH 10
SWDT
SCLK
XLAT

Q101

12 20 16 17 18
OPTICAL PICK-UP
(KMS-260A/J1N)

20 5 23 41 36 35 37 38 48 47 46 45
FOCUS/TRACKING COIL DRIVE,

SWDT
SCLK
XLAT

MNT0
MNT1
MNT2
MNT3
DQSY

XINT
SQSY

SENS
SRDT
SPINDLE/SLED MOTOR DRIVE 49 LDON
IC152
SCTX 42

MD MECHANISM CONTROLLER
PSB 16 40 DIG-RST IC316 (1/2)

LDOUT
44 WRPWR

LDIN
S681
50 MOD LIMIT-IN 59
(LIMIT IN)
+3.3V
51 52
SPFD S687
M901 6 OUT4F IN4R 3 PB-P 61
(SPINDLE) M 8 OUT4R IN4F 4
SPRD
13 75 66 64 65 74 73 62 63
(PB POSITION)

RECP
BOTM
ABCD
AUX2
AUX1

PEAK

S688
SE
TE
FE

9 10 REC-P 60
APCREF AUTOMATIC (REC POSITION)
83 IN1 IN2
POWER
CONTROL LOADING VREF 7 REFLECT 55 S682
SFDR ANALOG MUX
M902 27 OUT2F IN2F 29 92 MOTOR DRIVE (REFLECT)
(SLED) M 25 OUT2R IN2R 30 91
SRDR
IC153 VC1 6
S683
A/D CONVERTER OUT1 OUT2 PROTECT 54
53 LD-LOW (PROTECT)
PWM GENERATOR

DIGITAL 4 2
SERVO
2-AXIS CHUCK-IN 58 S685
SIGNAL
DEVICE FROM CPU (CHUCKING IN)
FCS+ FFDR PROCESS
21 OUT1F IN1F 19 88 INTERFACE M REFERENCE
FRDR VOLTAGE SWITCH S686
(TRACKING)

23 OUT1R IN1R 18 89 PACK-OUT 57

M903
(FOCUS)

Q350 (PACK OUT)

XLRF XLAT (LOADING)
80
AUTO CKRF SCLK
81
SEQUENCER
FCS– DTRF
82
SWDT • SIGNAL PATH
TRK+ TFDR
12 OUT3F IN3F 14 86
TRDR DIGITAL SERVO : MD PLAY
TRK– 10 OUT3R IN3R 15 85 HF MODULE
SIGNAL PROCESSOR : MD REC
IC121 (2/2) SWITCH
IC103, Q102 – 104 : CD PLAY (DIGITAL OUT)

HF MODULE MOD

05
– 35 – – 36 –
 HCD-MD1EX

7-3. BLOCK DIAGRAM – MAIN Section –

A/D, D/A CONVERTER • SIGNAL PATH
IC201
: MD PLAY
AINL
DECIMATION ∆Σ 5
: MD REC
ADDT SDTO FILTER MODULATOR AINR
3 R-CH
(Page 36) C 14
: CD PLAY
DADT,BCK,
×8
∆Σ AOUTL : FM/AM
LRCK, FS256 DADT SDTI SERIAL MODULATOR & 26
(Page 36) D 13 I/O INTER-
LOW-PASS AOUTR
27 R-CH : TAPE PLAY
INTERFACE POLATOR
FILTER
XBCK
12
SCLK : TAPE REC
LRCK LRCK
11 MODE
CONTROL
INPUT SELECT SWITCH, R-CH

DEMO
PDAD

PDDA
FS256 MCLK CLOCK TONE CONTROL, ELECTRICAL VOLUME POWER AMP
15 J101
DIVIDER IC705 IC506
35 PHONES
24 23 16

REC
OUT
TONE VOL VOL BB BB
TONE VOLUME BASS BOOST OUT

AD-EN
DA-EN
MD OUT IN OUT IN

EMP
36 CONTROL 30 29 CONTROL 28 27 CONTROL 25 8 3
CIRCUIT CIRCUIT CIRCUIT
BUFFER
INPUT AMP
CD-L CD
(Page 34) A 37 SELECT
TC SWITCH
38
CPU INTERFACE R-CH R-CH
J501 ST

MUTE-B
MUTE-A
39

STBY-A
STBY-B
BB-SW
CLOCK
LATCH
+

DATA
L
TAPE
OUT
+ + L
R R-CH REC OUT MUTING 21 22 20 26 6 11 9 14 –
MUTING CONTROL SWITCH

DATA
Q702 Q705
+

CLK
LAT
J502
R-CH R
FEED BACK
TAPE
L
SWITCH D523 D522 –
IN Q709 TM101
R R-CH ATTENUATOR ATTENUATOR EEPROM SPEAKER
(–6dB) CONTROL SWITCH IC171 DC DETECT IMPEDANCE
Q704 Q706 D521 USE 4 – 16Ω
Q510, 511
R-CH
FAN MOTOR
M

SDA
SCL
DRIVE
R-CH Q518, 519

AD-EN
DA-EN
EMP
5 6 M501
STANDBY (FAN)
D710 SWITCH
AEP, UK models Q514, 520
25 24 7 79 80
MUTING CONTROL

SCL
DA-EN

SDA
AD-EN

EMP
FM 75Ω SWITCH
COAXIAL Q516

XOUT 13
FM/AM TUNER UNIT POWER SWITCH
X302
FM Q512
7MHz
AEP, UK models RELAY
FM ANT L-OUT
MD MECHANISM
XIN 15 + E
CONTROLLER (Page 40)
FM ANT R-OUT R-CH
IC316 (2/2)
POWER DOWN PWR-DWN
AM ANT SC PWR-DWN 19
BACK UP
DETECT F
RDS SIGNAL MUX 57 kHz OUT CIN CONTANS LOOP Q504, 505
FM-DET CLOCKED +3.3V (Page 40)
BUFFER 4 BAND-PASS 8 7 VARIABLE &
AM ANT OUT COMPARATOR RESET SIGNAL
Q713 FILTER FIXED DIVIDER BIPHASE
SYSTEM-RST 12 GENERATOR
SYMBOL
IC706 POWER OFF
AM LOOP DECODER

MAS-BUSY

MEC-BUSY
ANTENNA ANTENNA MUTE DRIVER
Q711, 712
CLOCK

RXD
MUTE

CLK
TXD
RDS DECODER OSCILLATOR
STEREO REGENERATION
IC710 & CLOCK
Except AEP, UK models & SYNC
TUNED 31 32 33 34 26
DIFFERENTIAL D707 RESET SIGNAL
DECODER
DI GENERATOR D+5V
OSCO

RDCL
OSCI

DO IC708
RDDA
CLK Q707
13 14 16 2 LEVEL LEVEL
CE
SHIFT SHIFT
X703
IC704 (1/3) IC704 (2/3)
4.332MHz RESET
SWITCH

DATA
Q710

CLK
LAT
87 86 84 85 83 82 88 20 21 77 75 37 38 39 31 41 35 78 79 80 74 76 34 100 15

POWER-ON
CLOCK

RDS/DATA

MUTE

RESET
CE

DATA-IN

RTS

MD-REST

DATA
CLOCK
LAT
DBFB

BACKUP
RDS/CLK
DATA-OUT

ATT/6DB
RECOUT-MUTE

TXD
MD-CLK

CTS
RXD
ST-MUTE
TUNED
STEREO

AU-BUS OUT
AU-BUS IN

MASTER CONTROLLER
(SYSTEM CONTROL)

XT1

XT2

X1

X2
IC707 (2/3)
05
16 17 14 13 11 10

LEVEL SHIFT X701 X702

IC704 (3/3) 32kHz 5MHz

– 37 – – 38 –
HCD-MD1EX

7-4. BLOCK DIAGRAM – DISPLAY/POWER SUPPLY Section –

FLUORESCENT
INDICATOR TUBE
FL901

59 – 33, 31 – 24
SEG0 – SEG34
DATA 42 16 SDATA
REMOTE CONTROL CLOCK 43 15 SCK
RECEIVER 90 SIRCS CS 44 14 CS
IC902 RESET 45 13 RST
GRID DRIVE
DIG15 61
Q902

10 – 1, 64 – 62
DIG2 – DIG14
FL/LED DRIVER
IC901
S901 – 915
KEY0 – KEY2
25 – 27

GRID DRIVE
DIG1 11
Q901

RY501
MASTER CONTROLLER ST +12V RELAY DRIVE RELAY
(SYSTEM CONTROL) LED DRIVE D902 FM/AM TUNER UNIT B+ Q506 E
IC707 (3/3) P1 17 (Page 38)
Q903 (FOR ILLUMINATION)
XIN XOUT
+7.5V +12V
A+7.5V RECT
21 20 REGULATOR REGULATOR T901
M62428AFP (IC705) B+ D524, 525
Q509 IC505 POWER
OSC TRANSFORMER

C910, R906
POWER AMP B+ RECT
D903 (IC506) D509
B–
D715
+5V
LED DRIVE RDS DECODER (IC710) B+ FAN MOTOR
LED-MD PLAY 73 MD ( D714
Q904 (M501) B–
(GREEN) D+5V
–27V
–27V RECT
REGULATOR
FL DRIVER (IC901) B– D503 – 505
D719 Q503
LED DRIVE
LED-MD PAUSE 72 MD P
Q905
(AMBER) D713
+5V
MASTER CONTROLLER (IC707) B+
BACK UP +3.3V
D716 MD MECHANISM
D905 +3.3V CONTROLLER (IC316) B+ BA701
LED-MD REC 68 LED DRIVE +3.3V
REGULATOR LITHIUM
Q906 REC MD SERVO SECTION B+
IC192 BATTERY
D718

D907
MOTOR +5V D717 +3.3V
SYS +3.3V
MD MOTOR/COIL DRIVER (IC152), REGULATOR
MD SERVO SECTION B+
OVER WRITE HEAD DRIVE CIRCUIT B+ IC502
LED DRIVE
LED-CD PLAY 70 CD ( Except Singapore,
Q908
(GREEN) D709 +5.7V Hong Kong models
CD +5V B+ SWITCH VF
REGULATOR AC
CD SERVO SECTION B+ Q507, 508
IC503 (TO FL901) VF

LED DRIVE AC IN
LED-CD PAUSE 69 CD P MOTOR +7V
Q909 +7V
(AMBER) CD MOTOR/COIL DRIVER (IC102),
REGULATOR
CD LOADING MOTOR DRIVER (IC702), VOLTAGE
IC504
MD LOADING MOTOR DRIVER (IC153) B+ SELECTOR
S101
+5V RECT
LED DRIVE D906 AD/DA +5V Singapore, Hong Kong models
LED-MD DISC 67 REGULATOR
Q907 (MD DISC SLOT INDICATOR) A/D, D/A CONVERTER (IC201) B+ D510 – 513
IC501

D507 D506

PWR-DWN
CD-POWER 61 F
(Page 38)
05

– 39 – – 40 –
• Circuit Boards Location 7-5. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
Note on Schematic Diagram: Note on Printed Wiring Board:
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
AMP board 50 WV or less are not indicated except for electrolytics • ® : Through hole.
and tantalums. • b : Pattern from the side which enables seeing.
SENSOR board JOINT board • All resistors are in Ω and 1/4 W or less unless otherwise (The other layers' patterns are not indicated.)
specified.
• ¢ : internal component. Caution:
MOTOR board BD (CD) board • 2 : nonflammable resistor. Pattern face side: Parts on the pattern face side seen from
• C : panel designation. (Side B) the pattern face are indicated.
Parts face side: Parts on the parts face side seen from
Note: Note: (Side A) the parts face are indicated.
EJECT board The components identi- Les composants identifiés par
fied by mark ! or dotted une marque ! sont critiques • Indication of transistor.
line with mark ! are criti- pour la sécurité.
cal for safety. Ne les remplacer que par une C
Replace only with part piéce por tant le numéro
number specified. spécifié. Q These are omitted.
B E
• U : B+ Line.
• V : B– Line.
• H : adjustment for repair.
Q
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances. B C E
MAIN board • Waveforms are taken with a oscilloscope. These are omitted.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
PANEL board F : FM/AM
E : MD PLAY
q : MD REC
J : CD PLAY (ANALOG OUT)
POWER board c : CD PLAY (DEGITAL OUT)
d : TAPE PLAY
G : TAPE REC
• Abbreviation
CND : Canadian model.
SW board HK : Hong Kong model.
SP : Singapore model.
HP board
BD (MD) board

– 41 – – 42 –
HCD-MD1EX

7-6. PRINTED WIRING BOARD – BD (CD) Section – • See page 41 Circuit Boards Location.

(Page 57)

• Semiconductor • Semiconductor
Location Location
Ref. No. Location Ref. No. Location
IC103 C-1 IC101 B-1
IC102 B-1
Q101 B-3 IC104 C-3
Q103 C-3
Q102 B-1

– 43 – – 44 –
 HCD-MD1EX

7-7. SCHEMATIC DIAGRAM – BD (CD) Section – • See page 77 for Waveforms. • See page 79 for IC Block Diagrams.

(Page 59)

• Voltages and waveforms are dc with respect to ground

under no-signal conditions.
no mark : STOP
( ) : CD PLAY
∗ : Impossible to measure

The components identified by mark ! or dotted Les composants identifiés par une marque ! sont
line with mark ! are critical for safety. critiques pour la sécurité. Ne les remplacer que
Replace only with part number specified. par une piéce portant le numéro spécifié.

– 45 – – 46 –
HCD-MD1EX

7-8. PRINTED WIRING BOARD – BD (MD) Section – • See page 41 Circuit Boards Location.

(Page 75)

• Semiconductor (Page 57) • Semiconductor

Location Location
Ref. No. Location Ref. No. Location
D101 B-2 D181 B-1
D183 B-1
IC192 C-4
IC401 D-4 IC101 B-3
IC103 B-4
IC121 C-4
IC124 D-4
IC152 A-4
IC153 A-1
IC171 A-3
IC181 B-1
IC201 D-3
IC316 A-2

Q101 B-3
Q102 B-4
Q103 B-4
Q104 B-4
Q162 B-4
Q163 A-3
Q181 B-1
Q182 B-1
Q350 A-1

– 47 – – 48 –
 HCD-MD1EX
7-9. SCHEMATIC DIAGRAM – BD (MD) Section (1/3) – • See page 77 for Waveforms. • See page 82 for IC Block Diagrams.

(Page 51) (Page 51) (Page 52) (Page 52)

• Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : STOP
( ) : MD PLAY The components identified by mark ! or dotted Les composants identifiés par une marque ! sont
[ ] : MD REC line with mark ! are critical for safety. critiques pour la sécurité. Ne les remplacer que
∗ : Impossible to measure Replace only with part number specified. par une piéce portant le numéro spécifié.

– 49 – – 50 –
HCD-MD1EX • Voltages and waveforms are dc with respect to ground
under no-signal conditions.
no mark : STOP
( ) : MD PLAY
[ ] : MD REC
7-10. SCHEMATIC DIAGRAM – BD (MD) Section (2/3) – • See page 77 for Waveforms. • See page 82 for IC Block Diagrams. ∗ : Impossible to measure

(Page 49) (Page 49) (Page 50) (Page 50)

(Page
59)

(Page 53) (Page 53) (Page 54)

– 51 – – 52 –
 HCD-MD1EX

7-11. SCHEMATIC DIAGRAM – BD (MD) Section (3/3) – • See page 77 for Waveforms. • See page 82 for IC Block Diagrams.

(Page 51) (Page 51) (Page 52)

(Page 76)

• Voltages and waveforms are dc with respect to ground

under no-signal conditions.
no mark : STOP
( ) : MD PLAY
[ ] : MD REC
– 53 – – 54 – ∗ : Impossible to measure
HCD-MD1EX

7-12. PRINTED WIRING BOARD – MAIN Board (side A) – • See page 41 Circuit Boards Location.

– 55 – – 56 –
 HCD-MD1EX

7-13. PRINTED WIRING BOARD – MAIN Board (side B) – • See page 41 Circuit Boards Location.

(Page 72)
• Semiconductor
Location
Ref. No. Location
D701 D-4
D702 D-3
D703 C-2
D704 D-7
D705 B-6
D707 B-6
D708 C-7
D709 A-4
D710 A-3
D711 A-3
D712 B-3
D713 A-5
(Page 64) D714 A-4
D715 A-4
D716 A-5
D717 B-5
D718 A-7
D719 C-6
D720 A-4
D721 D-7

IC702 D-7
IC704 D-6
IC705 C-4
R831
IC706 C-6
IC707 B-7
IC708 B-6
IC710 A-2

Q701 C-1
Q702 B-1
Q703 B-1
Q704 A-1
Q705 A-2
Q706 A-1
Q707 D-6
Q708 D-3
Q709 B-2
Q710 B-6
Q711 C-7
Q712 C-7
Q713 C-2

(Page 75) (Page 75) (Page 48) (Page 44)

– 57 – – 58 –
HCD-MD1EX
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
7-14. SCHEMATIC DIAGRAM – MAIN Section (1/2) – • See page 78 for Waveforms. • See page 84 for IC Block Diagrams. ∗ : Impossible to measure

(Page 46)

(Page 61)

(Page 76)

(Page 76)
(Page 51)

(Page 61)

– 59 – – 60 –
 HCD-MD1EX

7-15. SCHEMATIC DIAGRAM – MAIN Section (2/2) – • See page 78 for Waveforms. • See page 84 for IC Block Diagrams.

(Page (Page 74)

60)

(Page 60)

(Page 65)

• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
no mark : FM
〈〈 〉〉 : AM
[ ] : CD PLAY
– 61 – – 62 – ( ) : MD PLAY
HCD-MD1EX

7-16. PRINTED WIRING BOARDS – PANEL Section – • See page 41 Circuit Boards Location.

(Page 57)
(Page 64)

(Page 63)

(Page 68)

• Semiconductor Location
Ref. No. Location Ref. No. Location
D901 C-4 Q901 B-3
D902 B-3 Q902 A-3
D903 D-3 Q903 C-3
D905 E-4 Q904 D-3
D907 D-2 Q905 D-3
Q906 E-4
IC901 B-2 Q907 D-3
IC902 C-4 Q908 D-1
Q909 D-1

– 63 – – 64 –
 HCD-MD1EX

7-17. SCHEMATIC DIAGRAM – PANEL Section – • See page 85 for IC Block Diagrams.

(Page 70)

(Page 62)

• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
no mark : FM

– 65 – – 66 –
HCD-MD1EX

7-18. PRINTED WIRING BOARDS – AMP/TRANSFORMER Section – • See page 41 Circuit Boards Location.

(Page 72)

(Page 64)

(Page 68)

(Page 68)

(Page 72)

(Page 72)

– 67 – – 68 –
 HCD-MD1EX

7-19. SCHEMATIC DIAGRAM – AMP/TRANSFORMER Section –

(Page 74)

(Page 73) (Page 74)

(Page 66)

• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
no mark : FM

The components identified by mark ! or dotted Les composants identifiés par une marque ! sont
line with mark ! are critical for safety. critiques pour la sécurité. Ne les remplacer que
Replace only with part number specified. par une piéce portant le numéro spécifié.

– 69 – – 70 –
HCD-MD1EX

7-20. PRINTED WIRING BOARD – POWER Section – • See page 41 Circuit Boards Location.

(Page 68)

(Page
67)

• Semiconductor Location
(Page 57) (Page 68)
Ref. No. Location Ref. No. Location
D501 B-4 IC501 C-5
D502 C-5 IC502 C-5
D503 D-5 IC503 B-1
D504 D-5 IC504 B-1
D505 D-5 IC505 B-4
D506 A-4
D507 A-4 Q503 D-5
D508 D-5 Q504 B-4
D509 A-4 Q505 A-4
D510 B-5 Q506 B-5
D511 B-5 Q507 C-5
D512 B-5 Q508 C-5
D513 B-5 Q509 C-4
D518 C-3 Q510 C-4
D519 C-5 Q511 C-4
D520 D-3 Q512 C-5
D521 D-3 Q514 C-5
D524 A-3 Q516 C-5
D525 A-3 Q518 D-3
D526 D-3 Q519 D-3
D527 D-3 Q520 B-5

– 71 – – 72 –
 HCD-MD1EX

7-21. SCHEMATIC DIAGRAM – POWER Section –

(Page 62)

(Page 69)

(Page 69)

(Page 69)

• Voltages and waveforms are dc with respect to ground

under no-signal (detuned) conditions.
no mark : FM The components identified by mark ! or dotted Les composants identifiés par une marque ! sont
[ ] : CD PLAY line with mark ! are critical for safety. critiques pour la sécurité. Ne les remplacer que
( ) : MD PLAY Replace only with part number specified. par une piéce portant le numéro spécifié.

– 73 – – 74 –
HCD-MD1EX

7-22. PRINTED WIRING BOARDS – MOTOR/SW Section – 7-23. SCHEMATIC DIAGRAM – MOTOR/SW Section –

(Page 57)

(Page 57)

(Page 60)

(Page 60)

(Page 48)

(Page 54)

– 75 – – 76 –
• Waveforms
– BD (CD) Board – – BD (MD) Board –

1 IC101 #¡ (RFO) (CD Play Mode) 6 IC103 @∞ (XPCK) 1 IC101 1, 2 (I, J) (MD Play Mode)
500 mV/DIV, 500 ns/DIV

5.3 Vp-p Approx.

500 mVp-p
1.3 ± 0.3 Vp-p

14 ns
2 IC101 $¢ (TEI) (CD Play Mode) 7 IC103 @™ (BCLK) 2 IC101 4 (A) (MD Play Mode)
50 mV/DIV, 1 µs/DIV

5 Vp-p Approx.
Approx. 200 mVp-p
100 mVp-p

474 ns
3 IC101 2 (FEI) (CD Play Mode) 8 IC103 @º (LRCK) 3 IC101 8, 9 (E, F) (MD Play Mode)
50 mV/DIV, 1 µs/DIV

Approx.
Approx. 5.1 Vp-p 150 mVp-p
150 mVp-p

44.1 kHz

4 IC103 3 (MDP) (CD Play Mode) 9 IC104 6 (XTO) 4 IC101 #• (RF) (MD Play Mode)

2.6 Vp-p
Approx.
4.6 Vp-p 1.2 ± 0.2 Vp-p

16.9344 MHz
7.6 µs

5 IC103 @• (RFCK) 5 IC152 #™ (CAPA–) (MD Play Mode)

5.1 Vp-p 4.6 Vp-p

7.35 kHz
1.5 µsec

– 77 –
 – MAIN Board –

6 IC152 #¡ (CAPA+) (MD Play Mode) !¡ IC121 @¶ (FS256) 1 IC707 !¡ (X1)

4.6 Vp-p 3.4 Vp-p 3.8 Vp-p

11.2896 MHz 5 MHz

1.5 µsec

7 IC121 (º (FS4) !™ IC316 !£ (XOUT) 2 IC707 !¢ (XT1)

3.4 Vp-p 3.3 Vp-p 2.4 Vp-p

7 MHz 32 kHz
5.7 µsec

8 IC121 !¶ (OSCO) 3 IC710 !£

3.1 Vp-p 2.7 Vp-p

22.5792 MHz 4.332 MHz

– PANEL Board –
9 IC121 @∞ (LRCK)
1 IC901 @º (XOUT)

3.4 Vp-p
4.7 Vp-p

44.1 kHz

2.6 µs
!º IC121 @§ (XBCK)
2 IC901 @¡ (XIN)

3.5 Vp-p
0.8 Vp-p

2.8224 MHz

2.6 µs

– 78 –
• IC Block Diagrams
– BD (CD) Board –
IC101 CXA1782BQ

RF M
PHD2

PHD1

RF O

RF I
PHD

CC1

CC2

FOK
LD

CP

CB
36 35 34 33 32 31 30 29 28 27 26 25

+
–

–
+

–
+

+
+
–
+
–

–
APC LEVELS

+
–
+ +

–
+ 24 SENS
–

IIL
–
FOK

–
MIRR
+

RF IV AMP1 DFCT
TTL 23 C. OUT

– 22 XRST
+

TTL
RF IV AMP2 21 DATA
FE BIAS 37 TTL • IIL DATA RESISTOR • INPUT SHIFT RESISTOR
• ADDRESS DECODER 20 XLT
+ IIL
–
FE AMP

IIL • OUTPUT DECODER 19 CLK

F 38 –
+

–
F IV AMP TOG1-3 FS1-4 TG1-2 TM1-7 PS1-4
+

BAL1-3
18 VCC
E 39 – FZC COMP
+

+
–

E IV AMP + +
–

EI 40

TE AMP
–
BAL1

BAL2

BAL3

• TRACKING
• ISET 17 ISET
• PHASE
HPF COMP LPF COMP
COMPENSATION
VEE 41
– TM6
TEO 42 TG1
–
+

+ 16 SL 0

TM5
TOG1

TOG2

TOG3

+
TM4 15 SL M
–
TZC COMP • FCS PHASE
LPFI 43 COMPENSATION
TM3 TM2 14 SL P
TEI 44
DFCT
ATSC 45 • WINDOW COMP FS1
TM1
+

TM7
ATSC 13 TA O
TZC 46 FS2 –

TDFCT 47
DFCT
TG2
+

• F SET

–
–
VC 48 FS4
+

1 2 3 4 5 6 7 8 9 10 11 12
FEO

FEI

FDFCT

FGD

FLB

FE O

FE M

SRCH

TGU

TG2

FSET

TA M

– 79 –
IC102 BA6397FP

27 OUT4A

26 OUT4B

18 OUT3B

17 OUT3A
25 IN4A

24 IN4B

20 IN3B

19 IN3A
28 GND

16 OP+

15 OP–
22 VCC

21 VCC
23 VC
VCC VCC

DRIVE
DRIVE DRIVE
BUFFER
BUFFER BUFFER
DRIVE
BUFFER
LEVEL

LEVEL
SHIFT

SHIFT
SHUT DOWN
THERMAL

REGULATOR
DRIVER MUTE
LEVEL

LEVEL
SHIFT

SHIFT

DRIVE DRIVE DRIVE

DRIVE BUFFER BUFFER
BUFFER
BUFFER
IN2B 10

OUT2A 11

OUT2B 12

GND 13

OP-OUT 14
1

9
OUT1A

OUT1B

IN1A

IN1B

TR-B

REG 0

XRST

GND

IN2A

IC103 CXD2507AQ
SPOD
XLON

SPOC
SPOB
SPOA

DATO
CLKO

CLOK
XLTO

XLAT
CNIN
SEIN
VDD

64 63 62 61 60 59 58 57 56 55 54 53 52

SERVO AUTO
FOK 1 5 51 DATA
SEQUENCER
MON 2 50 XRST
MDP 3 49 SENS
CPU SUB CODE
MDS 4 14 INTERFACE PROCESSOR 48 MUTE
DIGITAL
LOCK 5 4 CLV 47 SQCK
TEST 6 46 SQSO
FILO 7 45 EXCK
DIGITAL EFM
FILI 8 44 SBSO
PLL DEMODULATOR
PCO 9 43 SCOR
VSS 10 3 42 VSS
AVSS 11 41 WFCK
ASYMMETRY
CLTV 12 CORRECTOR 40 EMPH
D/A DIGITAL
AVDD 13 5 39 DOUT
INTERFACE OUT
RF 14 38 C4M
6
GENERATOR

BIAS 15 37 FSTT
CLOCK

ASYI 16 36 XTSL
16K ERROR
ASYO 17 RAM CORRECTOR 35 XTAO
ASYE 18 3 34 XTAI
WDCK 19 33 MNTO

20 21 22 23 24 25 26 27 28 29 30 31 32
LRCK
PCMD
BCLK
GTOP
XUGF
XPCK
VDD
GFS
RFCK
CZPO
XROF
MNT3
MNT1

– 80 –
IC104 PCM1710U-B

LRCIN 1 28 ML/DSD

INPUT
DIN 2 27 MC/DM2
INTERFACE DIGITAL MODE
FILTER CONTROL
BCKIN 3 26 MD/DM1

CLKO 4 TIMING 25 MUTE

CONTROL

XTI 5 24 MODE

XTO 6 23 CKSL
NOISE
SHAPER
DGND 7 22 DGND

VDD 8 21 VDD
5-LEVEL DAC 5-LEVEL DAC
RIGHT LEFT
VCC2R 9 20 VCC2L

GND2R 10 LOW-PASS FILTER LOW-PASS FILTER 19 GND2L

RIGHT LEFT

EXT1R 11 18 EXT1L

3-STAGE AMP 3-STAGE AMP

EXT2R 12 LEFT 17 EXT2L
RIGHT

VOUTR 13 16 VOUTL

GND1 14 15 VCC1

– 81 –
– BD (MD) Board –
IC101 CXA2523AR

COMPO
COMPP
MORFO

RF AGC
MORFI

ADDC

PEAK
AGCI
OPN

OPO
RFO

RF
48 47 46 45 44 43 42 41 40 39 38 37
USROP
–
+ RF AGC EQ
+
– USRC
RFA1
DET EQ
+
–

BPF3T
RFA2 RFA3 AUX
I 1 –1 HLPT PEAK3T
–1 3T SW
– P-P
–2
J 2 – –2

OFST 3T WBL
PTGR TEMP
– PEAK
1
– –2
CVB + –2 BOTTOM 36 BOTM
–1 PBH
VC 3 – GRV
GRVA PBSW WBL
35 ABCD
34 FE
+ –
A 4 – 33 AUX
– AA –
IVR – ABCDA BPFC

32 ADFG

B 5 + 31 ADAGC
IVR – BB +
+ 30 ADIN
–
– FEA

C 6 +
IVR – CC DET
BPF22
–
– ADIP
+ WBL 29 ADFM
AGC
D 7 + + ATA
IVR – DD
WBL
–1 TG
28 SE
– PTGR –2
E 8 + SEA
+ EE' +
IVR – EE – 27 CSLED
– +
EFB TESW –1 TG
26 TE
EBAL –2
TEA
ESW
F 9 +
+
IVR – FF WBL
– FF'
3T VI CONV 25 WBLADJ
IV
GSW FBAL EQ

PD 10 AUXSW
COMMAND BGR
+ –

+ – VREF
SCRI - PARA
APC 11 DECODE
APCREF 12

13 14 15 16 17 18 19 20 21 22 23 24
GND

TEMPI

TEMPR

SWDT

SCLK

XLAT

XSTBY

F0CNT

VREF

EQADJ
3TADJ

VCC

– 82 –
IC121 CXD2652AR

APCREF

F0CNT
TEST3
TEST2
TEST1

SRDR

DVDD

DCHG
EFMO

SPRD

TRDR
LDDR
DVSS

FRDR
SFDR

ADFG
SPFD

TFDR

DTRF
CKRF
FFDR

XLRF
FGIN

APC
FS4
100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76

SEQUENCER
SPINDLE PWM 75 AUX2

AUTO
SERVO GENERATOR 74 TE
MNT0 1
73 SE
MNT1 2 MONITOR EACH
CONTROL BLOCK 72 AVSS
MNT2 3
MNT3 4 71 ADRB
ADIP 70 ADRT
DECODER
69 AVDD
SWDT 5
SCLK 6 68 ADIO

XLAT 7 CPU I/F EACH

67 VC
BLOCK SERVO A/D
SRDT 8 66 AUX1
DSP CONVERTER
SENS 9 ANALOG 65 FE
MUX 64 ABCD
XRST 10
63 BOTM
SQSY 11 SUBCODE 62 PEAK
DQSY 12 PROCESSOR

61 CLTV
RECP 13
60 FILO

PLL
59 FILI

EFM/ACIRC
ENCODER/
DECODER
58 PCO

SHOCK RESISTANT
XINT 14 57 PDO
MEMORY CONTROLLER
TX 15 56 AVSS
OSCI 16
CLOCK EACH
OSCO 17
GENERATOR BLOCK
XTSL 18 55 RFI
COMP
NC 19 DIGITAL SAMPLING 54 BIAS
AUDIO RATE
DVSS 20 53 AVDD
I/F CONVERTER
DIN 21 52 ASYI
DOUT 22 51 ASYO

ADDT 23 ATRAC
ENCODER/DECODER
DADT 24

LRCK 25

ADDRESS/DATA BUS A00 - A11, D0 - D3

26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50
XBCK
FS256
DVDD

A03
A02
A01
A00
A10
A04
A05
A06
A07
A08
A11
DVSS
XOE
XCAS
A09
XRAS
XWE
D1
D0
D2
D3

MVCI

IC152 BH6511FS-E2
PGND2

PGND1
OUT2R

OUT1R
CAPA–

CAPA+

OUT2F

OUT1F
VM12
IN2R

IN1R
IN2F

VM2

VM1

IN1F

VDD

32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17

INTERFACE AMP AMP AMP AMP INTERFACE VDD

CHARGE PREDRIVE PREDRIVE

PUMP.
OSC

PREDRIVE PREDRIVE

INTERFACE AMP AMP AMP AMP INTERFACE PSB

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
GND

VG

IN4R

IN4F

VM4

OUT4F

PGND4

OUT4R

VM34

OUT3R

PGND3

OUT3F

VM3

IN3F

IN3R

PSB

– 83 –
IC153 LB1830M-S-TE-L IC201 AK4520A-VF-E2

CMODE
IN2 IN1 VM VREF VCONT

AOUTR
AOUTL

PWAD

PWDA
VCOM

DGND

DEM1

DEM0

MCLK
TST1

TST2

TST3
10 9 8 7 6

VD
VREF 28 27 26 25 24 23 22 21 20 19 18 17 16 15

LOGIC ∆Σ 8× CLOCK
PREDRIVER LPF
MODULATOR INTERPOLATOR DIVIDER

∆Σ 8×
LPF
MODULATOR INTERPOLATOR

COMMON SERIAL I/O

VOLTAGE INTERFACE

∆Σ DECIMATION
MODULATOR FILTER

∆Σ DECIMATION
MODULATOR FILTER
1 2 3 4 5
VCC OUT2 GND OUT1 VS
1 2 3 4 5 6 7 8 9 10 11 12 13 14

VREFH
VREFL

AINR+
AINR–
AINL+
AINL–

VA

AGND

DIF0
DIF1
LRCK
SCLK

SDTI
SDTO
– MAIN Board –
IC702 LB1641 IC706 M62016L

T.S.D O.C.P COM

+ INTERRUPT SIGNAL
MOTOR MOTOR – GENERATING BLOCK
DRIVE DRIVE

COM
+ RESET SIGNAL
– GENERATING BLOCK

FWD/REV/STOP
CONTROL LOGIC 1 2 3 4 5
GND INT RESET CD VCC
1 2 3 4 5 6 7 8 9 10
FILTER
MOTOR
GND

FILTER

CLAMP

FWD.IN

REV.IN

VCC 1

VCC 2

MOTOR
NOISE
NOISE
DRIVE

DRIVE

– 84 –
IC710 BU1922-E2 (AEP, UK)

TSTLD
OSCO
RDCL

VDDD

TEST
OSCI

VSSD
TS7
16 15 14 13 12 11 10 9

TEST LOGIC AND OUTPUT

SELECTOR SWITCH

OSCILLATOR 57kHz ANTI-

QUALITY BIT RECONSTRUCTION
AND BANDPASS ALIASING
GENERATOR FILTER
DIVIDER (8th ORDER) FILTER

BIPHASE CONTAS LOOP

DEFFERENTIAL CLOCKED
SYMBOL VARIABLE AND
DECODER COMPARATOR
DECODER FIXED DIVIDER

CLOCK REGENERATION
AND SYNC

VP1

REFERENCE
VOLTAGE

1 2 3 4 5 6 7 8
QUAL

RDDA

Vref

MUX

VDDA

VSSA

CIN

SCOUT

– PANEL Board –
IC901 M66004M8FP

DIG11 1 DIGITAL 64 DIG12

| | OUTPUT | |
DIG0 12 CIRCUIT 61 DIG15

RES 13

INDICATION
CS 14 SERIAL CONTROLLER
CLK 15 RECEIVE
DATA 16 CIRCUIT
CODE SELECT

OUTPUT INDICATION
P1 17 PORT CONTROL
(2BIT) RESISTOR
P0 18
VCC1 19

XOUT 20 CLOCK CODE/COMMAND

GENERATOR CONTROL
XIN 21
CIRCUIT CIRCUIT
VSS 22
RAM WRITE
CODE
WRITE
(35BIT x 16)

(35BIT x 16)
DECODER

DECODER

INDICATION
CODE
RESISTOR
(8BIT x 16)
60 VCC2

SEG35 23 59 SEG0
| | SEGMENT OUTPUT CIRCUIT | |
SEG27 31 33 SEG26

VP 32

– 85 –
7-24. IC PIN FUNCTION DESCRIPTION
• BD (MD) BOARD IC101 CXA2523AR (RF AMP, FOCUS/TRACKING ERROR AMP)
Pin No. Pin Name I/O Function
1 I I I-V converted RF signal I input from the optical pick-up block detector
2 J I I-V converted RF signal J input from the optical pick-up block detector
3 VC O Middle point voltage (+1.65V) generation output terminal
4 to 9 A to F I Signal input from the optical pick-up detector
10 PD I Light amount monitor input from the optical pick-up block laser diode
11 APC O Laser amplifier output terminal to the automatic power control circuit
12 APCREF I Reference voltage input terminal for setting laser power
13 GND — Ground terminal
14 TEMPI I Connected to the temperature sensor
15 TEMPR O Output terminal for a temperature sensor reference voltage
16 SWDT I Writing serial data input from the CXD2652AR (IC121)
17 SCLK I Serial data transfer clock signal input from the CXD2652AR (IC121)
18 XLAT I Serial data latch pulse signal input from the CXD2652AR (IC121)
19 XSTBY I Standby signal input terminal “L”: standby (fixed at “H” in this set)
Center frequency control voltage input terminal of internal circuit (BPF22, BPF3T, EQ) input
20 F0CNT I
from the CXD2652AR (IC121)
21 VREF O Reference voltage output terminal Not used (open)
22 EQADJ I Center frequency setting terminal for the internal circuit (EQ)
23 3TADJ I Center frequency setting terminal for the internal circuit (BPF3T)
24 VCC — Power supply terminal (+3.3V)
25 WBLADJ I Center frequency setting terminal for the internal circuit (BPF22)
26 TE O Tracking error signal output to the CXD2652AR (IC121)
27 CSLED I Connected to the external capacitor for low-pass filter of the sled error signal
28 SE O Sled error signal output to the CXD2652AR (IC121)
29 ADFM O FM signal output of the ADIP
30 ADIN I Receives a ADIP FM signal in AC coupling
31 ADAGC I Connected to the external capacitor for ADIP AGC
32 ADFG O ADIP duplex signal (22.05 kHz ± 1 kHz) output to the CXD2652AR (IC121)
33 AUX O Auxiliary signal (I3 signal/temperature signal) output to the CXD2652AR (IC121)
34 FE O Focus error signal output to the CXD2652AR (IC121)
35 ABCD O Light amount signal (ABCD) output to the CXD2652AR (IC121)
36 BOTM O Light amount signal (RF/ABCD) bottom hold output to the CXD2652AR (IC121)
37 PEAK O Light amount signal (RF/ABCD) peak hold output to the CXD2652AR (IC121)
38 RF O Playback EFM RF signal output to the CXD2652AR (IC121)
39 RFAGC I Connected to the external capacitor for RF auto gain control circuit
40 AGCI I Receives a RF signal in AC coupling
41 COMPO O User comparator output terminal Not used (open)
42 COMPP I User comparator input terminal Not used (fixed at “L”)
43 ADDC I Connected to the external capacitor for cutting the low band of the ADIP amplifier
44 OPO O User operational amplifier output terminal Not used (open)
45 OPN I User operational amplifier inversion input terminal Not used (fixed at “L”)
46 RFO O RF signal output terminal
47 MORFI I Receives a MO RF signal in AC coupling
48 MORFO O MO RF signal output terminal

– 86 –
• BD (MD) BOARD IC121 CXD2652AR
(DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, EFM/ACIRC ENCODER/DECODER,
SHOCK PROOF MEMORY CONTROLLER, ATRAC ENCODER/DECODER, 2M BIT D-RAM)

Pin No. Pin Name I/O Function

Focus OK signal output to the MD mechanism controller (IC316)
1 MNT0 (FOK) O
“H” is output when focus is on (“L”: NG)
2 MNT1 (SHCK) O Track jump detection signal output to the MD mechanism controller (IC316)
3 MNT2 (XBUSY) O Busy signal output to the MD mechanism controller (IC316)
4 MNT3 (SLOC) O Spindle servo lock status monitor signal output to the MD mechanism controller (IC316)
5 SWDT I Writing serial data signal input from the MD mechanism controller (IC316)
6 SCLK I Serial data transfer clock signal input from the MD mechanism controller (IC316)
7 XLAT I Serial data latch pulse signal input from the MD mechanism controller (IC316)
8 SRDT O (3) Reading serial data signal output to the MD mechanism controller (IC316)
9 SENS O (3) Internal status (SENSE) output to the MD mechanism controller (IC316)
10 XRST I Reset signal input from the MD mechanism controller (IC316) “L”: reset
Subcode Q sync (SCOR) output to the MD mechanism controller (IC316)
11 SQSY O
“L” is output every 13.3 msec Almost all, “H” is output

12 Digital In U-bit CD format subcode Q sync (SCOR) output to the MD mechanism controller
DQSY O
(IC316) “L” is output every 13.3 msec Almost all, “H” is output
Laser power selection signal input from the MD mechanism controller (IC316)
13 RECP I
“H”: recording mode, “L”: playback mode
14 XINT O Interrupt status output to the MD mechanism controller (IC316)

15 TX I Recording data output enable signal input from the MD mechanism controller (IC316)
Writing data transmission timing input (Also serves as the magnetic head on/off output)
16 OSCI I System clock signal (512Fs=22.5792 MHz) input terminal
17 OSCO O System clock signal (512Fs=22.5792 MHz) output terminal
Input terminal for the system clock frequency setting
18 XTSL I
“L”: 45.1584 MHz, “H”: 22.5792 MHz (fixed at “H” in this set)
19 RVDD — Power supply terminal (+3.3V) (digital system)
20 RVSS — Ground terminal (digital system)
21 DIN I Digital audio signal input terminal when recording mode (for digital in)
22 DOUT O Digital audio signal output terminal when playback mode (for digital out) Not used
23 ADDT I Recording data input from the A/D, D/A converter (IC201)
24 DADT O Playback data output to the A/D, D/A converter (IC201)
25 LRCK O L/R sampling clock signal (44.1 kHz) output to the A/D, D/A converter (IC201)
26 XBCK O Bit clock signal (2.8224 MHz) output to the A/D, D/A converter (IC201)
27 FS256 O Clock signal (11.2896 MHz) output to the A/D, D/A converter (IC201)
28 DVDD — Power supply terminal (+3.3V) (digital system)
29 to 32 A03 to A00 O Address signal output to the D-RAM (IC124)
33 A10 O Address signal output to the external D-RAM Not used (open)
34 to 38 A04 to A08 O Address signal output to the D-RAM (IC124)
39 A11 O Address signal output to the external D-RAM Not used (open)
40 DVSS — Ground terminal (digital system)
41 XOE O Output enable signal output to the D-RAM (IC124) “L” active
42 XCAS O Column address strobe signal output to the D-RAM (IC124) “L” active
43 A09 O Address signal output to the D-RAM (IC124)
44 XRAS O Row address strobe signal output to the D-RAM (IC124) “L” active
45 XWE O Write enable signal output to the D-RAM (IC124) “L” active
46 D1 I/O Two-way data bus with the D-RAM (IC124)
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.

– 87 –
 Pin No. Pin Name I/O Function
47 D0 I/O
48 D2 I/O Two-way data bus with the D-RAM (IC124)
49 D3 I/O
50 MVCI I Digital in PLL oscillation input from the external VCO Not used (fixed at “L”)
51 ASYO O Playback EFM full-swing output terminal
52 ASYI I (A) Playback EFM asymmetry comparator voltage input terminal
53 AVDD — Power supply terminal (+3.3V) (analog system)
54 BIAS I (A) Playback EFM asymmetry circuit constant current input terminal
55 RFI I (A) Playback EFM RF signal input from the CXA2523AR (IC101)
56 AVSS — Ground terminal (analog system)
57 PDO O (3) Phase comparison output for clock playback analog PLL of the playback EFM Not used (open)
58 PCO O (3) Phase comparison output for master clock of the recording/playback EFM master PLL
59 FILI I (A) Filter input for master clock of the recording/playback master PLL
60 FILO O (A) Filter output for master clock of the recording/playback master PLL
61 CLTV I (A) Internal VCO control voltage input of the recording/playback master PLL
62 PEAK I (A) Light amount signal (RF/ABCD) peak hold input from the CXA2523AR (IC101)
63 BOTM I (A) Light amount signal (RF/ABCD) bottom hold input from the CXA2523AR (IC101)
64 ABCD I (A) Light amount signal (ABCD) input from the CXA2523AR (IC101)
65 FE I (A) Focus error signal input from the CXA2523AR (IC101)
66 AUX1 I (A) Auxiliary signal (I3 signal/temperature signal) input from the CXA2523AR (IC101)
67 VC I (A) Middle point voltage (+1.65V) input from the CXA2523AR (IC101)
68 ADIO O (A) Monitor output of the A/D converter input signal Not used (open)
69 AVDD — Power supply terminal (+3.3V) (analog system)
70 ADRT I (A) A/D converter operational range upper limit voltage input terminal (fixed at “H” in this set)
71 ADRB I (A) A/D converter operational range lower limit voltage input terminal (fixed at “L” in this set)
72 AVSS — Ground terminal (analog system)
73 SE I (A) Sled error signal input from the CXA2523AR (IC101)
74 TE I (A) Tracking error signal input from the CXA2523AR (IC101)
75 AUX2 I (A) Auxiliary signal input terminal Not used (fixed at “H”)
76 DCHG I (A) Connected to the +3.3V power supply
77 APC I (A) Error signal input for the laser automatic power control Not used (fixed at “H”)
78 ADFG I ADIP duplex FM signal (22.05 kHz ± 1 kHz) input from the CXA2523AR (IC101)
79 F0CNT O Filter f0 control signal output to the CXA2523AR (IC101)
80 XLRF O Serial data latch pulse signal output to the CXA2523AR (IC101)
81 CKRF O Serial data transfer clock signal output to the CXA2523AR (IC101)
82 DTRF O Writing serial data output to the CXA2523AR (IC101)
Control signal output to the reference voltage generator circuit for the laser automatic power
83 APCREF O
control
84 LDDR O PWM signal output for the laser automatic power control Not used (open)
85 TRDR O Tracking servo drive PWM signal (–) output to the BH6511FS (IC152)
86 TFDR O Tracking servo drive PWM signal (+) output to the BH6511FS (IC152)
87 DVDD — Power supply terminal (+3.3V) (digital system)
88 FFDR O Focus servo drive PWM signal (+) output to the BH6511FS (IC152)
89 FRDR O Focus servo drive PWM signal (–) output to the BH6511FS (IC152)
90 FS4 O Clock signal (176.4 kHz) output terminal (X’tal system) Not used (open)
91 SRDR O Sled servo drive PWM signal (–) output to the BH6511FS (IC152)
92 SFDR O Sled servo drive PWM signal (+) output to the BH6511FS (IC152)
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.

– 88 –
 Pin No. Pin Name I/O Function
93 SPRD O Spindle servo drive PWM signal (–) output to the BH6511FS (IC152)
94 SPFD O Spindle servo drive PWM signal (+) output to the BH6511FS (IC152)
95 FGIN I
96 TEST1 I
Input terminal for the test (fixed at “L”)
97 TEST2 I
98 TEST3 I
99 DVSS — Ground terminal (digital system)
100 EFMO O EFM signal output terminal when recording mode
* I (A) for analog input, O (3) for 3-state output, and O (A) for analog output in the column I/O.

– 89 –
• BD (MD) BOARD IC316 M30610MCA-272FP (MD MECHANISM CONTROLLER)
Pin No. Pin Name I/O Function
1 JOG0 I Rotary encoder jog dial pulse input terminal Not used (fixed at “H”)
2 JOG1 I Rotary encoder jog dial pulse input terminal Not used (fixed at “H”)
3 DAOUT0 O Monitor output terminal for the test C1 error rate is output when test mode
4 DAOUT1 O Monitor output terminal for the test ADER is output when test mode
Subcode Q sync (SCOR) input from the CXD2652AR (IC121)
5 SQSY I
“L” is input every 13.3 msec Almost all, “H” is input
6 REMCON I Remote control signal input terminal Not used (fixed at “H”)
7 EMP O Emphasis control signal output to the A/D, D/A converter (IC201)
8 BYTE I External data bus line byte selection signal input “L”: 16 bit, “H”: 8 bit (fixed at “L”)
9 CNVSS — Ground terminal
10 XT-IN I Sub system clock input terminal Not used (fixed at “L”)
11 XT-OUT O Sub system clock output terminal Not used (pull down)
System reset signal input from the reset signal generator (IC706) and master controller (IC707)
12 SYSTEM-RST I “L”: reset
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
13 XOUT O Main system clock output terminal (7 MHz)
14 GND — Ground terminal
15 XIN I Main system clock input terminal (7 MHz)
16 +3.3V — Power supply terminal (+3.3V)
17 NMI I Non-maskable interrupt input terminal (fixed at “H” in this set)
Audio line muting on/off control signal output terminal “L”: line muting on
18 AMUTE O
Not used (pull down)
19 PWR-DWN I Power down detection signal input terminal “L”: power down, normally: “H”
Digital In U-bit CD format subcode Q sync (SCOR) input from the CXD2652AR (IC121)
20 DQSY I
“L” is input every 13.3 msec Almost all, “H” is input
Strobe signal output to the power supply circuit “H”: power on, “L”: standby mode
21 STB O
Not used (pull down)
22 DARST O Reset signal output terminal “L”: reset Not used (pull down)
23 XINT I Interrupt status input from the CXD2652AR (IC121)

24 DA-EN Enable signal output to the A/D, D/A converter (IC201) (for D/A converter block)
O
“L”: enable

25 AD-EN Enable signal output to the A/D, D/A converter (IC201) (for A/D converter block)
O
“L”: enable
26 MEC-BUSY O MD mechanism controller busy status monitor output to the master controller (IC707)
27 FLCS O Chip select signal output terminal Not used (pull down)
28 FLCLK O Display serial data transfer clock signal output terminal Not used (pull down)
29 — I Not used (fixed at “L”)
30 FLDATA O Display serial data output terminal Not used (pull down)
31 TXD O UART communication data output to the master controller (IC707)
32 RXD I UART communication data input from the master controller (IC707)
33 CLK I Serial clock signal input from the master controller (IC707)
34 MAS-BUSY I Master controller busy status monitor input from the master controller (IC707)
35 SWDT O Writing data output to the CXD2652AR (IC121)
36 SRDT I Reading data input from the CXD2652AR (IC121)
37 SCLK O Serial clock signal output to the CXD2652AR (IC121)
38 XLAT O Serial data latch pulse signal output to the CXD2652AR (IC121)
39 — I Not used (fixed at “L”)
40 DIG-RST O Reset signal output to the CXD2652AR (IC121) and BH6511FS (IC152) “L”: reset

– 90 –
 Pin No. Pin Name I/O Function
41 SENS I Internal status (SENSE) input from the CXD2652AR (IC121)
Recording data output enable signal output to the CXD2652AR (IC121) and overwrite head
42 SCTX O driver (IC181) Writing data transmission timing output (Also serves as the magnetic head
on/off output)
43 XINT O Not used (pull down)

44 WRPWR Laser power select signal output to the CXD2652AR (IC121) and HF module switch circuit
O
“L”: playback mode, “H”: recording mode
45 MNT3 I Spindle servo lock status monitor signal input from the CXD2652AR (IC121)
46 MNT2 I Busy signal input from the CXD2652AR (IC121)
47 MNT1 I Track jump detection signal input from the CXD2652AR (IC121)

48 I Focus OK signal input from the CXD2652AR (IC121)

MNT0
“H” is input when focus is on (“L”: NG)
49 LDON O Laser diode on/off control signal output to the automatic power control circuit “H”: laser on
Laser modulation select signal output to the HF module switch circuit
Playback power: “H”, Stop: “L”,
Recording power:
0.5 sec
50 MOD O

2 sec

51 LDIN O Motor control signal output to the loading motor driver (IC153) “L” active *1
52 LDOUT O Motor control signal output to the loading motor driver (IC153) “L” active *1
Loading motor drive voltage control signal output for the loading motor driver (IC153)
53 LD-LOW O
“H” active
54 PROTECT I Rec-proof claw detect input from the protect detect switch (S683) “H”: write protect
Detection input from the disc reflection rate detect switch (S682)
55 REFLECT I
“L”: high reflection rate disc, “H”: low reflection rate disc
56 PACK-IN I Detection input from the disc detect switch Not used (fixed at “H”)
Detection input from the loading-out detect switch (S686)
57 PACK-OUT I
“L” at a load-out position, others: “H”
58 CHUCK-IN I Detection input from the disc chucking-in detect switch (S685) “L”: chucking

59 LIMIT-IN Detection input from the sled limit-in detect switch (S681)
I
The optical pick-up is inner position when “L”
60 REC-P I Detection input from the recording position detect switch (S688) “L” active
61 PB-P I Detection input from the playback position detect switch (S687) “L” active
62 +3.3V — Power supply terminal (+3.3V)
63 — I Not used (fixed at “L”)
64 GND — Ground terminal
65 to 78 — I Not used (fixed at “L”)
79 SDA I/O Two-way data bus with the EEPROM (IC171)
80 SCL O Serial clock signal output to the EEPROM (IC171)

*1 Loading motor (M903) control

Mode
LOADING EJECT BRAKE RUN IDLE
Terminal
LDIN (pin %¡) “L” “H” “L” “H”
LDOUT (pin %™) “H” “L” “L” “H”

– 91 –
Pin No. Pin Name I/O Function
81, 82 — I Not used (fixed at “L”)
83 POWER O Power on/off control signal output terminal Not used (pull down)
84 to 90 — I Not used (fixed at “L”)
91 to 93 KEY0 to KEY2 I Key input terminal (A/D input) Not used (fixed at “H”)
94 — I Not used (fixed at “L”)
95 SOURCE I Not used (fixed at “L”)
96 AVSS — Ground terminal (for A/D converter)
97 — I Not used (fixed at “L”)
98 VREF3.3V I Reference voltage (+3.3V) input terminal (for A/D converter)
99 +3.3V — Power supply terminal (+3.3V) (for analog system )
100 — I Not used (fixed at “L”)

– 92 –
• MAN BOARD IC707 µPD78078GF-083-3BA
(MASTER CONTROLLER (CD MECHANISM CONTROL/SYSTEM CONTROL))

Pin No. Pin Name I/O Function

1 VER I Destination setting terminal Not used (open)
2 VER I Destination setting terminal US, Canadian models: fixed at “L”, Other models: open
Destination setting terminal
3 VER I
US, Canadian, Singapore, Hong Kong models: fixed at “L”, Other models: open
4 VER I Destination setting terminal Not used (open)
5 to 7 NC O Not used (open)
8 — O Not used (open)
9 IC — Connected to ground
10 X2 O Main system clock output terminal (5 MHz)
11 X1 I Main system clock input terminal (5 MHz)
12 VDD — Power supply terminal (+5V)
13 XT2 O Sub system clock output terminal (32 kHz)
14 XT1 I Sub system clock input terminal (32 kHz)

15 RESET System reset signal input from the reset signal generator (IC708) “L”: reset
I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”
16 AU-BUS IN I Audio bus signal input terminal
17 AU-BUS OUT O Audio bus signal output terminal
18 ENC/A I Rotary encoder jog dial pulse input terminal (A phase input) Not used (fixed at “L”)
19 ENC/B I Rotary encoder jog dial pulse input terminal (B phase input) Not used (fixed at “L”)

20 RDS/CLK RDS serial data transfer clock signal input from the RDS decoder (IC710)
I
Used for the AEP, UK models
RDS serial data input from the RDS decoder (IC710)
21 RDS/DATA I
Used for the AEP, UK models
22 SCOR I Subcode sync (S0+S1) detection signal input from the CXD2507AQ (IC103)
23 AVDD — Power supply terminal (+5V) (for A/D converter)
24 AVREF0 I Reference voltage (+5V) input terminal (for A/D converter)
25 KEY0 I Key input terminal (A/D input) I/u (power) key input (S903)

26 KEY1 Key input terminal (A/D input) CD p, CD ^, CD §, MD p, MD ^, MD §, VOLUME +/

I
– keys input (S902, 905, 907, 909, 911, 913 to 915)

27 KEY2 Key input terminal (A/D input) FUNCTION, CD/MD ) + TUNING +, TUNER/BAND,
I
CD/MD = 0 TUNING –, REC, CD-MD SYNC keys input (S901, 904, 906, 908, 910, 912)
28 to 30 — O Not used (open)
31 RTS O Master controller busy status monitor output to the MD mechanism controller (IC316)
32 MD-POWER O MD system power supply on/off control signal output terminal Not used (open)
33 AVSS — Ground terminal (for A/D converter)
34 POWER-ON O System power supply on/off control signal output terminal “L”: power on, “H”: standby
35 MD-REST O Reset signal output to the MD mechanism controller (IC316) “H”: reset
36 AVREF1 I Reference voltage (+5V) input terminal (for A/D converter)
37 RXD I UART communication data input from the MD mechanism controller (IC316)
38 TXD O UART communication data output to the MD mechanism controller (IC316)
39 MD-CLK O Serial clock signal output to the MD mechanism controller (IC316)
40 VSS — Ground terminal
41 CTS I MD mechanism controller busy status monitor input from the MD mechanism controller (IC316)
42 DATA O Display serial data output to the FL driver (IC901)
43 CLOCK O Display serial data transfer clock signal output to the FL driver (IC901)
44 CS O Chip select signal output to the FL driver (IC901) “L”: data output

– 93 –
 Pin No. Pin Name I/O Function
45 RESET O Reset signal output to the FL driver (IC901) “L”: reset
46 SUBQ I Subcode Q data input from the CXD2507AQ (IC103)
47 NC O Not used (open)
48 SQCLK O Subcode Q data reading clock signal output to the CXD2507AQ (IC103)
49 CLOCK O Serial data transfer clock signal output to the CXD2507AQ (IC103) and PCM1710U (IC104)
50 DATA O Serial data output to the CXD2507AQ (IC103) and PCM1710U (IC104)
51 XLT O Serial data latch pulse signal output to the CXD2507AQ (IC103)
52 PRGL (DF-LAT) O Serial data latch pulse signal output to the PCM1710U (IC104)
53 SENSE I Internal status input from the CXD2507AQ (IC103)
54 ADJ I Setting terminal for the CD test mode “L”: CD test mode Normally: fixed at “H”
55 IN-SW I Detection input from the disc detect switch (S104) “L”: disc in
56 OUT-SW I Detection input from the disc detect (S104) “L”: disc out
57 LOAD-OUT O Motor control signal output to the CD lid open/close motor driver (IC702) “L” active *1
58 LOAD-IN O Motor control signal output to the CD lid open/close motor driver (IC702) “L” active *1
59 FOCUS-SW O Focus gain control signal output to the CXA1782BQ (IC101) “L”: normal, “H”: down

60 BD-REST O Reset signal output to the CXA1782BQ (IC101), BA6297FP (IC102) and CXD2507AQ (IC103)
“L”: reset
61 CD-POWER O CD servo system power supply on/off control signal output terminal “H”: power on
Tuner system power supply on/off control signal output terminal “H”: power on
62 ST-POWER O
Not used (open)
63 D.IN.SELECT O Digital input selection signal output terminal Not used (open)
64 to 66 — O Not used (open)
67 LED-MD DISC O LED drive signal output of the MD disc slot indicator (D906) “L”: LED on
68 LED-MD REC O LED drive signal output of the REC indicator (D905) “L”: LED on
69 LED-CD PAUSE O LED drive signal output of the CD P indicator (D907 amber) “L”: LED on
70 LED-CD PLAY O LED drive signal output of the CD ( indicator (D907 green) “L”: LED on
71 VSS — Ground terminal
72 LED-MD PAUSE O LED drive signal output of the MD P indicator (D903 amber) “L”: LED on
73 LED-MD PLAY O LED drive signal output of the MD ( indicator (D903 green) “L”: LED on
74 DBFB O DBFB on/off control signal output terminal “L”: DBFB on
75 RECOUT-MUTE O Muting on/off control signal output for the TAPE OUT signal “L”: muting on
76 MUTE O Audio muting on/off control signal output terminal
77 ATT/6DB O –6 dB attenuator control signal output for the TAPE IN signal “L”: attenuator on
78 DATA O Serial data output to the M62428AFP (IC705)
79 CLOCK O Serial data transfer clock signal output to the M62428AFP (IC705)
80 LAT O Serial data latch pulse signal output to the M62428AFP (IC705)
81 GND — Ground terminal
82 STEREO I FM stereo detection signal input from the FM/AM tuner unit “L”: stereo
83 TUNED I Tuning detection signal input from the FM/AM tuner unit “L”: tuned, “H”; detuned
84 DATA-IN I PLL serial data input from the FM/AM tuner unit
85 DATA-OUT O PLL serial data output to the FM/AM tuner unit
86 CLOCK O PLL serial data transfer clock signal output to the FM/AM tuner unit

*1 CD lid open/close motor (M103) control

Mode
OFF OPEN CLOSE BRAKE
Terminal
LOAD-OUT (pin %¶) “H” “L” “H” “L”
LOAD-IN (pin %•) “H” “H” “L” “L”

– 94 –
Pin No. Pin Name I/O Function
87 CE O PLL serial chip enable signal output to the FM/AM tuner unit
88 ST-MUTE O Tuner muting on/off control signal output to the FM/AM tuner unit “L”: muting on
89 FM/AM SELECT O FM/AM selection signal output terminal Not used (open)
90 SIRCS I Sircs signal input from the remote control receiver (IC902)
91 — O Not used (open)
92 — I Not used (fixed at “L”)
93 FAN SPEED O Fan motor speed control signal output terminal Not used (open)
94 FAN STOP O Fan motor on/off control signal output terminal Not used (open)
95 — O Not used (open)
96 MD1 I Setting terminal for the CPU operational mode (fixed at “H” in this set)
97 to 99 — I Not used (fixed at “L”)

100 BACKUP System reset signal input from the reset signal generator (IC708) “L”: reset
I
For several hundreds msec. after the power supply rises, “L” is input, then it changes to “H”

– 95 –
 SECTION 8
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by
may have some difference from the original are seldom required for routine service. Some mark ! or dotted line with mark
one. delay should be anticipated when ordering ! are critical for safety.
Replace only with part number
• Color Indication of Appearance Parts these items. specified.
Example: • The mechanical parts with no reference num-
KNOB, BALANCE (WHITE) . . . (RED) ber in the exploded views are not supplied. Les composants identifiés par une
marque ! sont critiquens pour la
↑ ↑ • Hardware (# mark) list is given in the last of sécurité.
Parts Color Cabinet's Color the electrical parts list. Ne les remplacer que par une pièce
• Abbreviation portant le numéro spécifié.
CND : Canadian
HK : Hong Kong
SP : Singapore

(1) PANEL, COVER SECTION

2 CD SECTION
3 #1
#1

6 4

#1

not supplied

CHASSIS
SECTION
not supplied

FRONT PANEL
SECTION
#4 6
1
7
#4 2

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 4-212-516-01 COVER (BOTTOM) (AEP, UK) 4 4-212-517-01 COVER (REAR)
1 4-212-516-11 COVER (BOTTOM) (SP, HK) 5 4-212-515-01 PANEL (R), SIDE
1 4-212-516-31 COVER (BOTTOM) (US, CND) 6 4-212-957-01 SCREW, SP FITTING ORNAMENTAL
2 3-363-099-01 SCREW (CASE 3 TP2) 7 3-704-515-11 SCREW (BV/RING)
3 4-212-514-01 PANEL (L), SIDE

– 96 –
(2) FRONT PANEL SECTION

57
56
55

54
62
53

62
52
58

61

59
60

52

51

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
51 4-212-503-01 PLATE (BUTTON), ORNAMENTAL * 57 A-4417-231-A PANEL BOARD, COMPLETE
52 4-212-531-01 SCREW * 58 1-671-424-11 HP BOARD
53 4-212-103-01 PLATE (GLASS), ORNAMENTAL 59 4-212-533-01 BUTTON (VOL)
54 4-212-502-01 PLATE (INDICATION WINDOW) 60 X-4950-365-1 PANEL ASSY, FRONT
55 4-212-532-01 BUTTON (POWER) (+, –, §) 61 4-212-528-01 WINDOW, INDICATION

56 4-212-507-01 BUTTON (EJECT) (§) 62 4-951-620-41 SCREW (2.6), +BVTP

– 97 –
(3) CD SECTION

114

113
115 not supplied

116 #2
112
111 108

110 108
not supplied
108
not supplied #2
103
not supplied 117
117
#3 122 not supplied
121
BU-22BD19
120
109 103
108
107 118
118
104
#10 M103
103
106 105
103 102
not supplied
101

103
103 119 103

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 101 1-671-426-11 EJECT BOARD 113 4-212-525-01 WINDOW (CD)
102 4-212-497-01 TABLE, DISC 114 4-212-504-01 PLATE (LID), ORNAMENTAL
103 4-951-620-41 SCREW (2.6), +BVTP 115 4-212-495-01 ARM, CHUCKING
* 104 1-671-428-11 MOTOR BOARD 116 4-212-500-01 PLATE (BU), ORNAMENTAL
105 X-4950-366-1 BRACKET (GEAR) ASSY 117 4-985-672-01 SCREW (+PTPWHM2.6), FLOATING

106 4-212-529-01 BELT 118 4-959-996-01 SPRING (932), COMPRESSION

107 4-212-492-01 GEAR (A) 119 4-212-499-01 HOLDER (BU)
108 3-325-697-01 WASHER 120 4-993-142-11 PULLEY (L), PRESS
109 X-4950-379-1 GEAR ASSY, WORM * 121 1-671-427-11 SENSOR BOARD
110 4-212-493-01 GEAR (B) 122 4-212-709-01 BRACKET (WORM)

111 4-212-494-01 GEAR (C) M103 A-4411-278-A MOTOR ASSY (CD LID OPEN/CLOSE)
112 4-212-708-01 GEAR (D)

– 98 –
(4) CHASSIS SECTION

154 156 158

A

#1 157
155 160
159
161
#1 #1
153 #1

156
152
#4 T901
A 162
#5 #1
151 #5

#1
B
#1
#4 #1 HK 163
#4
#3 not supplied M501
not supplied

#3 167
not
US/CND UK
supplied
#3 B B
not supplied

164 164
170 166
168 B 164 SP

#1
MDM-3J
169
168 AEP, SP, HK 165

not supplied

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 151 A-4417-232-A POWER BOARD, COMPLETE ! 163 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
* 152 1-671-772-11 AMP BOARD ! 164 1-575-651-21 CORD, POWER (AEP, SP, HK)
* 153 A-4417-230-A MAIN BOARD, COMPLETE (AEP, UK) ! 164 1-696-571-11 CORD, POWER (UK)
* 153 A-4417-310-A MAIN BOARD, COMPLETE (SP, HK) ! 164 1-783-531-31 CORD, POWER (US, CND)
* 153 A-4417-312-A MAIN BOARD, COMPLETE (US, CND) ! 165 1-569-008-21 ADAPTOR, CONVERSION 2P (SP)

154 1-790-106-11 WIRE (FLAT TYPE) (31 CORE) 166 1-773-009-11 WIRE (FLAT TYPE) (15 CORE)
155 1-775-170-11 WIRE (FLAT TYPE) (19 CORE) 167 1-693-407-21 TUNER (US, CND)
156 4-812-134-11 RIVET (DIA. 3.5), NYLON 167 1-693-409-21 TUNER (AEP, UK, SP, HK)
* 157 4-213-167-01 INSULATED PLATE 168 4-965-822-01 FOOT
* 158 1-671-425-11 JOINT BOARD 169 4-212-522-01 BRACKET (BOTTOM)

* 159 4-212-513-01 PANEL, BACK (US, CND, AEP, UK) 170 1-790-105-11 WIRE (FLAT TYPE) (25 CORE)
* 159 4-212-513-11 PANEL, BACK (SP, HK) M501 1-698-997-11 FAN, D.C.
* 160 4-212-527-01 COVER (FUSE) ! T901 1-433-472-11 TRANSFORMER, POWER (US, CND)
161 4-212-526-01 BRACKET (FAN) ! T901 1-433-473-11 TRANSFORMER, POWER (AEP, UK)
162 4-966-267-11 BUSHING (FBS001), CORD ! T901 1-433-474-11 TRANSFORMER, POWER (SP, HK)

– 99 –
(5) MD MECHANISM DECK SECTION-1
(MDM-3J)

208
208
207
207

not supplied
206

205 204
209

203

202

201 #6

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 201 A-4699-808-A BD (MD) BOARD, COMPLETE 206 4-986-959-01 WASHER, STOPPER
202 1-660-966-11 OP RELAY FLEXIBLE BOARD 207 4-987-327-01 INSULATOR
203 1-782-683-11 WIRE (FLAT TYPE) (14 CORE) 208 4-628-167-01 SCREW, STEP
204 X-4949-900-1 SHUTTER ASSY 209 4-997-962-01 SPRING (O/C), TENSION
205 4-997-456-02 SHAFT (SHUTTER) (A)

– 100 –
 HCD-MD1EX
Ver 1.1 2001.02

(6) MD MECHANISM DECK SECTION-2

(MDM-3J)
#3
255
261 264

260 263
not supplied
262
259 #3

265
267
266

#8 #9

258
#9

257
not supplied

255
268

M903

M902
269
M901
270
256
254
255
HR901
253
252

271
251 #7
The components identified by Les composants identifiés par une
mark 0 or dotted line with marque 0 sont critiques pour la
mark 0 are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
0 251 8-583-028-02 OPTICAL PICK-UP KMS-260A/J1N (for MD) 264 4-979-890-11 RETAINER (GEAR)
252 4-987-061-01 SPACER (RACK) 265 4-979-899-01 GEAR (LC)
253 4-963-914-02 RACK (INSERTER) 266 4-979-897-01 GEAR (LA)
254 3-366-890-11 SCREW (M1.4) 267 4-979-885-01 LEVER (HEAD UP)
255 3-342-375-11 SCREW (M1.7X1.4), SPECIAL 268 4-984-556-01 SHAFT (MAIN SHAFT)

* 256 1-667-719-11 SW BOARD 269 A-3304-200-A SCREW ASSY, LEAD

257 4-979-906-11 SPRING (LEAD SCREW) 270 4-988-560-01 SCREW (+P 1.7X6)
* 258 4-983-511-02 PIN (OUTSERT) 271 4-955-841-11 SCREW
259 A-4672-138-A SLIDER COMPLETE ASSY HR901 1-500-396-11 HEAD, OVER LIGHT (RF325-74A)
260 3-953-235-01 DAMPER, OIL M901 A-4672-135-A MOTOR ASSY, SPINDLE (for MD)

* 261 4-983-439-01 BRACKET (DAMPER) M902 A-4672-133-A MOTOR ASSY, SLED (for MD)
* 262 4-983-437-01 SLIDER (CAM) M903 A-4672-134-A MOTOR ASSY, LOADING (for MD)
263 4-979-898-01 GEAR (LB)

– 101 –
(7) CD BASE UNIT SECTION
(BU-22BD19)

305
306

307

M101

309
304

304 M102

303

308
302

301

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
301 4-951-620-01 SCREW (2.6X8), +BVTP 307 4-917-567-01 GEAR (M)
302 A-4673-402-A BD (CD) BOARD, COMPLETE 308 4-917-564-01 GEAR (P), FLATNESS
303 4-917-565-01 SHAFT, SLED 309 3-713-786-51 SCREW +P 2X3
304 4-951-940-01 INSULATOR (BU) M101 X-4942-405-1 BASE (OUTSART) ASSY (SPINDLE) (for CD)
! 305 8-848-379-31 OPTICAL PICK-UP KSS-213B/K-N (for CD) M102 X-4917-504-1 MOTOR ASSY (SLED) (for CD)

306 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)

– 102 –
 SECTION 9
ELECTRICAL PARTS LIST AMP BD (CD)
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by
parts list may be different from the parts speci- are seldom required for routine service. mark ! or dotted line with mark
fied in the diagrams or the components used Some delay should be anticipated when order- ! are critical for safety.
Replace only with part number
on the set. ing these items. specified.
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS
may have some difference from the original In each case, u: µ, for example: Les composants identifiés par une
marque ! sont critiquens pour la
one. uA. . : µA. . uPA. . : µPA. . sécurité.
• RESISTORS uPB. . : µPB. . uPC. . : µPC. . Ne les remplacer que par une pièce
All resistors are in ohms. uPD. . : µPD. . portant le numéro spécifié.
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF When indicating parts by reference
F: nonflammable • COILS number, please include the board.
• Abbreviation uH: µH
CND : Canadian
HK : Hong Kong
SP : Singapore

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
* 1-671-772-11 AMP BOARD C105 1-163-038-00 CERAMIC CHIP 0.1uF 25V
********** C106 1-164-690-91 CERAMIC CHIP 0.0022uF 5% 50V

< CAPACITOR > C107 1-164-690-91 CERAMIC CHIP 0.0022uF 5% 50V

C108 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C534 1-126-047-91 ELECT 4.7uF 20% 50V C109 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C535 1-126-047-91 ELECT 4.7uF 20% 50V C110 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C536 1-163-003-11 CERAMIC CHIP 330PF 10% 50V C111 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C537 1-163-003-11 CERAMIC CHIP 330PF 10% 50V
C539 1-126-022-11 ELECT 47uF 20% 25V C112 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C113 1-164-690-91 CERAMIC CHIP 0.0022uF 5% 50V
C540 1-126-022-11 ELECT 47uF 20% 25V C114 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C541 1-163-113-00 CERAMIC CHIP 68PF 5% 50V C115 1-126-607-11 ELECT CHIP 47uF 20% 4V
C542 1-163-113-00 CERAMIC CHIP 68PF 5% 50V C116 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
C543 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C546 1-126-964-11 ELECT 10uF 20% 50V C117 1-164-005-11 CERAMIC CHIP 0.47uF 25V
C118 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C547 1-126-964-11 ELECT 10uF 20% 50V C119 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C556 1-130-483-00 MYLAR 0.01uF 5% 50V C120 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
C557 1-130-483-00 MYLAR 0.01uF 5% 50V C121 1-163-038-00 CERAMIC CHIP 0.1uF 25V

< CONNECTOR > C122 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C123 1-163-038-00 CERAMIC CHIP 0.1uF 25V
* CN505 1-564-525-11 PLUG, CONNECTOR 10P C124 1-126-607-11 ELECT CHIP 47uF 20% 4V
C125 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
< IC > C126 1-163-038-00 CERAMIC CHIP 0.1uF 25V

IC506 8-759-333-24 IC LM1876TF C127 1-164-690-91 CERAMIC CHIP 0.0022uF 5% 50V

C128 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
< RESISTOR > C129 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C130 1-164-336-11 CERAMIC CHIP 0.33uF 25V
R520 1-216-049-11 RES, CHIP 1K 5% 1/10W C131 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R521 1-216-081-00 METAL CHIP 22K 5% 1/10W
R522 1-216-081-00 METAL CHIP 22K 5% 1/10W C132 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
R523 1-216-049-11 RES, CHIP 1K 5% 1/10W C133 1-163-145-00 CERAMIC CHIP 0.0015uF 5% 50V
R526 1-216-045-00 METAL CHIP 680 5% 1/10W C134 1-164-346-11 CERAMIC CHIP 1uF 16V
C135 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
R527 1-216-045-00 METAL CHIP 680 5% 1/10W C136 1-164-005-11 CERAMIC CHIP 0.47uF 25V
R528 1-216-081-00 METAL CHIP 22K 5% 1/10W
R529 1-216-081-00 METAL CHIP 22K 5% 1/10W C137 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
R550 1-216-069-00 METAL CHIP 6.8K 5% 1/10W C139 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R551 1-216-069-00 METAL CHIP 6.8K 5% 1/10W C140 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
************************************************************ C141 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C142 1-163-038-00 CERAMIC CHIP 0.1uF 25V
A-4673-402-A BD (CD) BOARD, COMPLETE
************************ C145 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
C146 1-135-201-11 TANTALUM CHIP 10uF 20% 4V
< CAPACITOR > C147 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C148 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C101 1-126-607-11 ELECT CHIP 47uF 20% 4V C149 1-164-346-11 CERAMIC CHIP 1uF 16V
C102 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C103 1-164-346-11 CERAMIC CHIP 1uF 16V C153 1-135-259-11 TANTALUM CHIP 10uF 20% 6.3V

– 103 –
 BD (CD) BD (MD)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C154 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
R144 1-216-073-00 METAL CHIP 10K 5% 1/10W
< CONNECTOR > R145 1-216-097-00 RES, CHIP 100K 5% 1/10W
R146 1-216-097-00 RES, CHIP 100K 5% 1/10W
CNU101 1-770-014-11 CONNECTOR, FFC/FPC 16P R147 1-216-049-11 RES, CHIP 1K 5% 1/10W
CNU102 1-770-013-11 CONNECTOR, FFC/FPC 19P R148 1-216-049-11 RES, CHIP 1K 5% 1/10W

< IC > R149 1-216-049-11 RES, CHIP 1K 5% 1/10W

R150 1-216-037-00 METAL CHIP 330 5% 1/10W
IC101 8-752-069-56 IC CXA1782BQ R151 1-216-037-00 METAL CHIP 330 5% 1/10W
IC102 8-759-291-06 IC BA6397FP R152 1-216-037-00 METAL CHIP 330 5% 1/10W
IC103 8-752-372-94 IC CXD2507AQ R153 1-216-082-00 RES, CHIP 24K 5% 1/10W
IC104 8-759-185-29 IC PCM1710U-B
R154 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
< TRANSISTOR > R156 1-216-085-00 METAL CHIP 33K 5% 1/10W
R157 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
Q101 8-729-010-08 TRANSISTOR MSB710-R R158 1-216-001-00 METAL CHIP 10 5% 1/10W
Q102 8-729-424-08 TRANSISTOR UN2111
Q103 8-729-421-22 TRANSISTOR UN2211 < VARIABLE RESISTOR >

< RESISTOR > RV101 1-223-587-11 RES, ADJ, CARBON 22K

RV102 1-223-587-11 RES, ADJ, CARBON 22K
R102 1-216-001-00 METAL CHIP 10 5% 1/10W RV103 1-223-587-11 RES, ADJ, CARBON 22K
R103 1-216-049-11 RES, CHIP 1K 5% 1/10W
R104 1-216-097-00 RES, CHIP 100K 5% 1/10W < SWITCH >
R105 1-216-093-00 METAL CHIP 68K 5% 1/10W
R106 1-216-093-00 METAL CHIP 68K 5% 1/10W S101 1-572-085-11 SWITCH, LEAF (LIMIT)

R107 1-216-093-00 METAL CHIP 68K 5% 1/10W < VIBRATOR >

R108 1-216-093-00 METAL CHIP 68K 5% 1/10W
R109 1-216-097-00 RES, CHIP 100K 5% 1/10W X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz)
R112 1-216-083-00 METAL CHIP 27K 5% 1/10W ************************************************************
R113 1-216-083-00 METAL CHIP 27K 5% 1/10W
* A-4699-808-A BD (MD) BOARD, COMPLETE
R114 1-216-101-00 METAL CHIP 150K 5% 1/10W ************************
R115 1-216-101-00 METAL CHIP 150K 5% 1/10W
R116 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < CAPACITOR >
R117 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R118 1-216-049-11 RES, CHIP 1K 5% 1/10W C101 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
C102 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R119 1-216-089-00 RES, CHIP 47K 5% 1/10W C103 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
R120 1-216-089-00 RES, CHIP 47K 5% 1/10W C104 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
R121 1-216-114-00 RES, CHIP 510K 5% 1/10W C105 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
R122 1-216-097-00 RES, CHIP 100K 5% 1/10W
R123 1-216-099-00 METAL CHIP 120K 5% 1/10W C106 1-163-275-11 CERAMIC CHIP 0.001uF 5% 50V
C107 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R124 1-216-091-00 METAL CHIP 56K 5% 1/10W C108 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R125 1-216-069-00 METAL CHIP 6.8K 5% 1/10W C109 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
R126 1-216-063-00 RES, CHIP 3.9K 5% 1/10W C110 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R127 1-216-089-00 RES, CHIP 47K 5% 1/10W
R128 1-216-105-00 RES, CHIP 220K 5% 1/10W C111 1-164-344-11 CERAMIC CHIP 0.068uF 10% 25V
C112 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
R129 1-216-049-11 RES, CHIP 1K 5% 1/10W C113 1-164-346-11 CERAMIC CHIP 1uF 16V
R130 1-216-079-00 METAL CHIP 18K 5% 1/10W C115 1-164-489-11 CERAMIC CHIP 0.22uF 10% 16V
R131 1-216-079-00 METAL CHIP 18K 5% 1/10W C116 1-163-037-11 CERAMIC CHIP 0.022uF 10% 25V
R132 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R133 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C117 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C118 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R134 1-216-065-00 RES, CHIP 4.7K 5% 1/10W C119 1-104-851-11 TANTALUM CHIP 10uF 20% 10V
R135 1-216-065-00 RES, CHIP 4.7K 5% 1/10W C121 1-126-206-11 ELECT CHIP 100uF 20% 6.3V
R136 1-216-073-00 METAL CHIP 10K 5% 1/10W C122 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
R137 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
R138 1-216-049-11 RES, CHIP 1K 5% 1/10W C123 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C124 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R139 1-216-033-00 METAL CHIP 220 5% 1/10W C127 1-163-038-00 CERAMIC CHIP 0.1uF 25V
R140 1-216-081-00 METAL CHIP 22K 5% 1/10W C128 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
R141 1-216-061-00 METAL CHIP 3.3K 5% 1/10W C129 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
R142 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R143 1-216-121-00 RES, CHIP 1M 5% 1/10W C130 1-163-251-11 CERAMIC CHIP 100PF 5% 50V

– 104 –
 BD (MD)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C131 1-163-023-00 CERAMIC CHIP 0.015uF 5% 50V C363 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C132 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C133 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C401 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C134 1-163-038-00 CERAMIC CHIP 0.1uF 25V C402 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C2001 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C135 1-163-038-00 CERAMIC CHIP 0.1uF 25V C2002 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C136 1-126-206-11 ELECT CHIP 100uF 20% 6.3V C2003 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C139 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C140 1-163-099-00 CERAMIC CHIP 18PF 5% 50V C2004 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C142 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
< CONNECTOR >
C143 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C144 1-163-251-11 CERAMIC CHIP 100PF 5% 50V CN101 1-766-508-11 CONNECTOR, FFC/FPC (ZIF) 22P
C151 1-126-206-11 ELECT CHIP 100uF 20% 6.3V CN104 1-778-283-11 CONNECTOR, FFC/FPC 4P
C152 1-163-038-00 CERAMIC CHIP 0.1uF 25V CN106 1-774-771-11 CONNECTOR, FFC/FPC 14P
C153 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V CN107 1-779-854-11 CONNECTOR, FFC/FPC 25P

C156 1-163-038-00 CERAMIC CHIP 0.1uF 25V < DIODE >

C158 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V
C160 1-104-601-11 ELECT CHIP 10uF 20% 10V D101 8-719-988-62 DIODE 1SS355
C161 1-104-601-11 ELECT CHIP 10uF 20% 10V D181 8-719-046-86 DIODE F1J6TP
C163 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V D183 8-719-046-86 DIODE F1J6TP

C164 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V < IC/TRANSISTOR >
C167 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C168 1-163-038-00 CERAMIC CHIP 0.1uF 25V IC101 8-752-080-95 IC CXA2523AR
C169 1-104-851-11 TANTALUM CHIP 10uF 20% 10V IC103 8-729-903-10 TRANSISTOR FMW1
C171 1-163-038-00 CERAMIC CHIP 0.1uF 25V IC121 8-752-384-47 IC CXD2652AR
IC124 8-759-536-21 IC MSM51V4400D-10TSK-FS
C181 1-126-206-11 ELECT CHIP 100uF 20% 6.3V IC152 8-759-430-25 IC BH6511FS-E2
C182 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C183 1-163-038-00 CERAMIC CHIP 0.1uF 25V IC153 8-759-481-19 IC LB1830M-S-TE-L
C184 1-117-970-11 ELECT CHIP 22uF 20% 10V IC171 8-759-484-73 IC BR24C01AF-E2
C185 1-164-611-11 CERAMIC CHIP 0.001uF 10% 500V IC181 8-759-481-17 IC MC74ACT08DTR2
IC192 8-759-460-72 IC BA033FP-E2
C188 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V IC201 8-759-471-38 IC AK4520A-VF-E2
C189 1-163-989-11 CERAMIC CHIP 0.033uF 10% 25V
C190 1-126-206-11 ELECT CHIP 100uF 20% 6.3V IC316 8-759-568-55 IC M30610MCA-272FP
C191 1-163-038-00 CERAMIC CHIP 0.1uF 25V IC401 8-759-242-70 IC TC7WU04F
C192 1-163-038-00 CERAMIC CHIP 0.1uF 25V
< COIL/RESISTOR >
C197 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C201 1-164-690-91 CERAMIC CHIP 0.0022uF 5% 50V L101 1-414-235-22 INDUCTOR CHIP 0uH
C202 1-164-690-91 CERAMIC CHIP 0.0022uF 5% 50V L102 1-414-235-22 INDUCTOR CHIP 0uH
C203 1-163-038-00 CERAMIC CHIP 0.1uF 25V L103 1-414-235-22 INDUCTOR CHIP 0uH
C205 1-126-206-11 ELECT CHIP 100uF 20% 6.3V L105 1-414-235-22 INDUCTOR CHIP 0uH
L106 1-414-235-22 INDUCTOR CHIP 0uH
C206 1-115-363-11 CERAMIC CHIP 10uF 10V
C207 1-163-038-00 CERAMIC CHIP 0.1uF 25V L121 1-414-235-22 INDUCTOR CHIP 0uH
C208 1-115-363-11 CERAMIC CHIP 10uF 10V L122 1-414-235-22 INDUCTOR CHIP 0uH
C209 1-163-038-00 CERAMIC CHIP 0.1uF 25V L151 1-412-622-51 INDUCTOR 10uH
C210 1-163-038-00 CERAMIC CHIP 0.1uF 25V L152 1-412-622-51 INDUCTOR 10uH
L153 1-412-039-51 INDUCTOR CHIP 100uH
C212 1-163-038-00 CERAMIC CHIP 0.1uF 25V
C213 1-115-363-11 CERAMIC CHIP 10uF 10V L154 1-412-039-51 INDUCTOR CHIP 100uH
C214 1-115-363-11 CERAMIC CHIP 10uF 10V L161 1-414-235-22 INDUCTOR CHIP 0uH
C216 1-124-779-00 ELECT CHIP 10uF 20% 16V L162 1-414-235-22 INDUCTOR CHIP 0uH
C350 1-163-038-00 CERAMIC CHIP 0.1uF 25V L181 1-424-675-11 INDUCTOR 0uH
L201 1-412-776-11 INDUCTOR 1uH
C352 1-124-779-00 ELECT CHIP 10uF 20% 16V
C353 1-163-038-00 CERAMIC CHIP 0.1uF 25V L301 1-414-235-22 INDUCTOR CHIP 0uH
C354 1-163-038-00 CERAMIC CHIP 0.1uF 25V L351 1-216-295-00 SHORT 0
C355 1-163-251-11 CERAMIC CHIP 100PF 5% 50V L401 1-216-025-00 RES, CHIP 100 5% 1/10W
C357 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V L1001 1-500-445-21 FERRITE 0uH

C358 1-163-251-11 CERAMIC CHIP 100PF 5% 50V < TRANSISTOR >

C359 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C361 1-163-038-00 CERAMIC CHIP 0.1uF 25V Q101 8-729-028-91 TRANSISTOR DTA144EUA-T106
C362 1-163-251-11 CERAMIC CHIP 100PF 5% 50V Q102 8-729-026-53 TRANSISTOR 2SA1576A-T106-QR

– 105 –
 BD (MD)
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q103 8-729-028-99 TRANSISTOR RT1N144M-TP-1 R189 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q104 8-729-028-99 TRANSISTOR RT1N144M-TP-1
Q162 8-729-101-07 TRANSISTOR 2SB798-DL R190 1-216-073-00 METAL CHIP 10K 5% 1/10W
R195 1-216-295-00 SHORT 0
Q163 8-729-028-91 TRANSISTOR DTA144EUA-T106 R196 1-216-295-00 SHORT 0
Q181 8-729-018-75 FET 2SJ278MY R197 1-216-295-00 SHORT 0
Q182 8-729-017-65 FET 2SK1764KY R198 1-216-295-00 SHORT 0
Q350 8-729-028-99 TRANSISTOR RT1N144M-TP-1
R199 1-216-295-00 SHORT 0
< RESISTOR > R200 1-216-295-00 SHORT 0
R202 1-216-041-00 METAL CHIP 470 5% 1/10W
R101 1-216-025-00 RES, CHIP 100 5% 1/10W R203 1-216-025-00 RES, CHIP 100 5% 1/10W
R103 1-216-049-11 RES, CHIP 1K 5% 1/10W R204 1-216-025-00 RES, CHIP 100 5% 1/10W
R104 1-216-073-00 METAL CHIP 10K 5% 1/10W
R105 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R210 1-216-041-00 METAL CHIP 470 5% 1/10W
R106 1-216-133-00 METAL CHIP 3.3M 5% 1/10W R330 1-216-073-00 METAL CHIP 10K 5% 1/10W
R331 1-216-073-00 METAL CHIP 10K 5% 1/10W
R107 1-216-113-00 METAL CHIP 470K 5% 1/10W R332 1-216-097-00 RES, CHIP 100K 5% 1/10W
R110 1-216-073-00 METAL CHIP 10K 5% 1/10W R333 1-216-073-00 METAL CHIP 10K 5% 1/10W
R112 1-216-089-00 RES, CHIP 47K 5% 1/10W
R113 1-216-049-11 RES, CHIP 1K 5% 1/10W R351 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R115 1-216-049-11 RES, CHIP 1K 5% 1/10W R352 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R356 1-216-025-00 RES, CHIP 100 5% 1/10W
R117 1-216-113-00 METAL CHIP 470K 5% 1/10W R361 1-216-073-00 METAL CHIP 10K 5% 1/10W
R121 1-216-097-00 RES, CHIP 100K 5% 1/10W R362 1-216-025-00 RES, CHIP 100 5% 1/10W
R125 1-216-025-00 RES, CHIP 100 5% 1/10W
R128 1-216-041-00 METAL CHIP 470 5% 1/10W R363 1-216-073-00 METAL CHIP 10K 5% 1/10W
R131 1-216-073-00 METAL CHIP 10K 5% 1/10W R366 1-216-097-00 RES, CHIP 100K 5% 1/10W
R367 1-216-097-00 RES, CHIP 100K 5% 1/10W
R132 1-216-097-00 RES, CHIP 100K 5% 1/10W R379 1-216-073-00 METAL CHIP 10K 5% 1/10W
R133 1-216-117-00 METAL CHIP 680K 5% 1/10W R380 1-216-073-00 METAL CHIP 10K 5% 1/10W
R134 1-216-049-11 RES, CHIP 1K 5% 1/10W
R135 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R381 1-216-073-00 METAL CHIP 10K 5% 1/10W
R136 1-216-049-11 RES, CHIP 1K 5% 1/10W R382 1-216-073-00 METAL CHIP 10K 5% 1/10W
R383 1-216-073-00 METAL CHIP 10K 5% 1/10W
R137 1-216-025-00 RES, CHIP 100 5% 1/10W R384 1-216-073-00 METAL CHIP 10K 5% 1/10W
R140 1-216-029-00 METAL CHIP 150 5% 1/10W R386 1-216-073-00 METAL CHIP 10K 5% 1/10W
R142 1-216-073-00 METAL CHIP 10K 5% 1/10W
R143 1-216-073-00 METAL CHIP 10K 5% 1/10W R387 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R144 1-216-025-00 RES, CHIP 100 5% 1/10W R388 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R389 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R146 1-216-037-00 METAL CHIP 330 5% 1/10W R391 1-216-073-00 METAL CHIP 10K 5% 1/10W
R147 1-216-025-00 RES, CHIP 100 5% 1/10W R393 1-216-073-00 METAL CHIP 10K 5% 1/10W
R148 1-216-045-00 METAL CHIP 680 5% 1/10W
R158 1-216-097-00 RES, CHIP 100K 5% 1/10W R400 1-216-073-00 METAL CHIP 10K 5% 1/10W
R159 1-216-097-00 RES, CHIP 100K 5% 1/10W R401 1-216-089-00 RES, CHIP 47K 5% 1/10W
R402 1-216-113-00 METAL CHIP 470K 5% 1/10W
R161 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R405 1-216-063-00 RES, CHIP 3.9K 5% 1/10W
R162 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R420 1-216-097-00 RES, CHIP 100K 5% 1/10W
R163 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R164 1-216-033-00 METAL CHIP 220 5% 1/10W R421 1-216-097-00 RES, CHIP 100K 5% 1/10W
R165 1-216-097-00 RES, CHIP 100K 5% 1/10W R422 1-216-097-00 RES, CHIP 100K 5% 1/10W
R423 1-216-097-00 RES, CHIP 100K 5% 1/10W
R166 1-220-149-11 REGISTER 2.2 10% 1/2W R424 1-216-097-00 RES, CHIP 100K 5% 1/10W
R167 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R425 1-216-097-00 RES, CHIP 100K 5% 1/10W
R169 1-219-724-11 METAL CHIP 1 1% 1/4W
R170 1-216-073-00 METAL CHIP 10K 5% 1/10W R429 1-216-097-00 RES, CHIP 100K 5% 1/10W
R171 1-216-073-00 METAL CHIP 10K 5% 1/10W R430 1-216-097-00 RES, CHIP 100K 5% 1/10W
R431 1-216-097-00 RES, CHIP 100K 5% 1/10W
R175 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R432 1-216-097-00 RES, CHIP 100K 5% 1/10W
R177 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R433 1-216-097-00 RES, CHIP 100K 5% 1/10W
R178 1-216-295-00 SHORT 0
R179 1-216-091-00 METAL CHIP 56K 5% 1/10W R434 1-216-097-00 RES, CHIP 100K 5% 1/10W
R180 1-216-073-00 METAL CHIP 10K 5% 1/10W R435 1-216-097-00 RES, CHIP 100K 5% 1/10W
R438 1-216-097-00 RES, CHIP 100K 5% 1/10W
R182 1-216-089-00 RES, CHIP 47K 5% 1/10W R439 1-216-097-00 RES, CHIP 100K 5% 1/10W
R183 1-216-089-00 RES, CHIP 47K 5% 1/10W R440 1-216-097-00 RES, CHIP 100K 5% 1/10W
R184 1-216-073-00 METAL CHIP 10K 5% 1/10W
R188 1-216-073-00 METAL CHIP 10K 5% 1/10W R441 1-216-097-00 RES, CHIP 100K 5% 1/10W

– 106 –
 BD (MD) EJECT HP JOINT
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R442 1-216-097-00 RES, CHIP 100K 5% 1/10W < DIODE >
R443 1-216-097-00 RES, CHIP 100K 5% 1/10W
R444 1-216-097-00 RES, CHIP 100K 5% 1/10W D906 8-719-069-45 LED SELU5E23C-TP15
R445 1-216-097-00 RES, CHIP 100K 5% 1/10W (MD DISC SLOT INDICATOR)

R448 1-216-097-00 RES, CHIP 100K 5% 1/10W < JACK >

R449 1-216-097-00 RES, CHIP 100K 5% 1/10W
R451 1-216-097-00 RES, CHIP 100K 5% 1/10W J101 1-691-293-51 JACK (PHONES)
R454 1-216-097-00 RES, CHIP 100K 5% 1/10W
R455 1-216-097-00 RES, CHIP 100K 5% 1/10W < RESISTOR >

R456 1-216-097-00 RES, CHIP 100K 5% 1/10W R104 1-202-997-11 RES, CHIP 270 5% 1/2W
R457 1-216-097-00 RES, CHIP 100K 5% 1/10W R105 1-202-997-11 RES, CHIP 270 5% 1/2W
R458 1-216-097-00 RES, CHIP 100K 5% 1/10W R935 1-216-025-00 RES, CHIP 100 5% 1/10W
R460 1-216-073-00 METAL CHIP 10K 5% 1/10W
R462 1-216-073-00 METAL CHIP 10K 5% 1/10W < SWITCH >

R502 1-216-295-00 SHORT 0 S906 1-762-875-21 SWITCH, KEYBOARD (TUNER/BAND)

R504 1-216-295-00 SHORT 0 ************************************************************
R600 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R602 1-216-025-00 RES, CHIP 100 5% 1/10W * 1-671-425-11 JOINT BOARD
R603 1-216-025-00 RES, CHIP 100 5% 1/10W ***********

R604 1-216-061-00 METAL CHIP 3.3K 5% 1/10W 1-533-293-11 FUSE HOLDER

R605 1-216-025-00 RES, CHIP 100 5% 1/10W
R606 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < CAPACITOR >
R607 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R608 1-216-025-00 RES, CHIP 100 5% 1/10W C101 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
(AEP, UK)
R2001 1-216-001-00 METAL CHIP 10 5% 1/10W C102 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
R2002 1-216-296-00 SHORT 0 (AEP, UK)
C103 1-164-222-11 CERAMIC CHIP 0.22uF 25V
< VIBRATOR > (AEP, UK)
C104 1-164-222-11 CERAMIC CHIP 0.22uF 25V
X101 1-767-286-11 VIBRATOR, CRYSTAL (22.5792MHz) (AEP, UK)
X302 1-767-670-11 VIBRATOR, CERAMIC (7MHz) C105 1-164-222-11 CERAMIC CHIP 0.22uF 25V
************************************************************ (AEP, UK)

* 1-671-426-11 EJECT BOARD C106 1-164-222-11 CERAMIC CHIP 0.22uF 25V

*********** (AEP, UK)

< CONNECTOR > < CONNECTOR >

* CN902 1-568-942-11 PIN, CONNECTOR 4P CN101 1-564-321-00 PIN, CONNECTOR 2P (US, CND, AEP, UK)
* CN101 1-564-687-11 PIN, CONNECTOR 3P (SP, HK)
< SWITCH > CN102 1-784-038-21 CONNECTOR, BOARD TO BOARD 9P
CN103 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P
S907 1-762-875-21 SWITCH, KEYBOARD (6 (CD)) * CN104 1-564-520-11 PLUG, CONNECTOR 5P
S916 1-570-953-11 SWITCH, PUSH
(CD LID OPEN/CLOSE DETECT) < DIODE >
************************************************************
D522 8-719-988-62 DIODE 1SS355
* 1-671-424-11 HP BOARD D523 8-719-988-62 DIODE 1SS355
*********
< FUSE >
< CAPACITOR >
! F101 1-532-388-51 FUSE (T2AL/250V) (SP, HK)
C107 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V ! F101 1-532-463-51 FUSE (T1AL/250V) (AEP, UK)
C108 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V ! F101 1-576-104-11 FUSE (2A/250V) (US, CND)
C109 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V
C932 1-163-141-00 CERAMIC CHIP 0.001uF 5% 50V < RESISTOR >

< CONNECTOR > ! R101 1-202-725-00 SOLID 3.3M 10% 1/2W

(US, CND)
CN903 1-506-468-11 PIN, CONNECTOR 3P R102 1-218-232-91 RES, CHIP 4.7 10% 1/2W
(AEP, UK)
R103 1-218-232-91 RES, CHIP 4.7 10% 1/2W
(AEP, UK)
R544 1-216-077-00 METAL CHIP 15K 5% 1/10W

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
– 107 – ber specified. portant le neméro spécifié.
 JOINT MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R547 1-216-077-00 METAL CHIP 15K 5% 1/10W C751 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C752 1-104-664-11 ELECT 47uF 20% 16V
< SWITCH > C753 1-130-477-00 MYLAR 0.0033uF 5% 50V

! S101 1-572-675-11 SWITCH, POWER VOLTAGE CHANGE C754 1-104-664-11 ELECT 47uF 20% 16V
(VOLTAGE SELECTOR) (SP, HK) C755 1-126-047-91 ELECT 4.7uF 20% 50V
C756 1-126-047-91 ELECT 4.7uF 20% 50V
< TERMINAL > C757 1-126-047-91 ELECT 4.7uF 20% 50V
C758 1-126-047-91 ELECT 4.7uF 20% 50V
TM101 1-694-471-11 TERMINAL BOARD (SPEAKER)
************************************************************ C759 1-126-047-91 ELECT 4.7uF 20% 50V
C760 1-126-047-91 ELECT 4.7uF 20% 50V
* A-4417-230-A MAIN BOARD, COMPLETE (AEP, UK) C761 1-126-047-91 ELECT 4.7uF 20% 50V
* A-4417-310-A MAIN BOARD, COMPLETE (SP, HK) C762 1-126-047-91 ELECT 4.7uF 20% 50V
* A-4417-312-A MAIN BOARD, COMPLETE (US, CND) C763 1-136-165-00 FILM 0.1uF 5% 50V
*********************
C764 1-136-165-00 FILM 0.1uF 5% 50V
< CAPACITOR > C766 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C768 1-126-960-11 ELECT 1uF 20% 50V
C702 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C769 1-126-957-11 ELECT 0.22uF 20% 50V
C703 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C770 1-126-957-11 ELECT 0.22uF 20% 50V
C704 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C705 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C772 1-130-473-00 MYLAR 0.0015uF 5% 50V
C709 1-126-925-11 ELECT 470uF 20% 10V C773 1-130-473-00 MYLAR 0.0015uF 5% 50V
C774 1-117-749-11 FILM CHIP 0.1uF 20% 50V
C710 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C775 1-117-749-11 FILM CHIP 0.1uF 20% 50V
C711 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C776 1-117-749-11 FILM CHIP 0.1uF 20% 50V
C712 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C713 1-104-664-11 ELECT 47uF 20% 16V C777 1-117-749-11 FILM CHIP 0.1uF 20% 50V
C714 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C779 1-126-964-11 ELECT 10uF 20% 50V
C780 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C715 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C781 1-104-664-11 ELECT 47uF 20% 16V
C716 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C782 1-104-664-11 ELECT 47uF 20% 16V
C717 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C718 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C783 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C719 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C784 1-163-235-11 CERAMIC CHIP 22PF 5% 50V
C785 1-163-234-11 CERAMIC CHIP 20PF 5% 50V
C720 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C787 1-104-664-11 ELECT 47uF 20% 16V
C721 1-126-964-11 ELECT 10uF 20% 50V C788 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C722 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C723 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V C789 1-126-059-11 ELECT 10uF 20% 50V
C724 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C790 1-126-059-11 ELECT 10uF 20% 50V
C791 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C726 1-104-664-11 ELECT 47uF 20% 16V C792 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C727 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C793 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C728 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C729 1-126-916-11 ELECT 1000uF 20% 6.3V C794 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C731 1-104-664-11 ELECT 47uF 20% 16V C795 1-104-664-11 ELECT 47uF 20% 16V
(AEP, UK)
C732 1-126-964-11 ELECT 10uF 20% 50V C796 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C733 1-126-964-11 ELECT 10uF 20% 50V (AEP, UK)
C734 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C797 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C735 1-163-005-11 CERAMIC CHIP 470PF 10% 50V C799 1-163-139-00 CERAMIC CHIP 820PF 5% 50V
C736 1-163-005-11 CERAMIC CHIP 470PF 10% 50V (AEP, UK)

C737 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C800 1-104-664-11 ELECT 47uF 20% 16V
C738 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C801 1-163-003-11 CERAMIC CHIP 330PF 10% 50V
C739 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V (AEP, UK)
C740 1-126-047-91 ELECT 4.7uF 20% 50V C802 1-163-011-11 CERAMIC CHIP 1500PF 10% 50V
C741 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V (AEP, UK)
C803 1-126-964-11 ELECT 10uF 20% 50V
C742 1-126-047-91 ELECT 4.7uF 20% 50V (AEP, UK)
C743 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V C804 1-163-017-00 CERAMIC CHIP 4700PF 10% 50V
C744 1-104-664-11 ELECT 47uF 20% 16V (AEP, UK)
C746 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C748 1-130-475-00 MYLAR 0.0022uF 5% 50V C805 1-126-961-11 ELECT 2.2uF 20% 50V
(AEP, UK)
C749 1-130-475-00 MYLAR 0.0022uF 5% 50V C806 1-163-239-11 CERAMIC CHIP 33PF 5% 50V
C750 1-104-664-11 ELECT 47uF 20% 16V (AEP, UK)

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
– 108 – ber specified. portant le numéro spécifié.
 MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
C807 1-163-239-11 CERAMIC CHIP 33PF 5% 50V IC704 8-759-269-09 IC SN74HCT04ANS
(AEP, UK) IC705 8-759-494-40 IC M62428AFP600C
C808 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V IC706 8-759-481-02 IC M62016L
(AEP, UK) IC707 8-759-545-08 IC uPD78078GF-083-3BA
C809 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
(AEP, UK) IC708 8-759-635-63 IC M51943BSL
IC710 8-759-450-88 IC BU1922-E2 (AEP, UK)
C810 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
(AEP, UK) < JACK >
C811 1-126-964-11 ELECT 10uF 20% 50V
(AEP, UK) J501 1-764-593-21 JACK 2P (TAPE, OUT)
C812 1-126-059-11 ELECT 10uF 20% 50V J502 1-764-593-21 JACK 2P (TAPE, IN)
C813 1-126-059-11 ELECT 10uF 20% 50V
C814 1-126-047-91 ELECT 4.7uF 20% 50V < SHORT >

C815 1-126-047-91 ELECT 4.7uF 20% 50V JW702 1-216-296-00 SHORT 0

C816 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V JW703 1-216-295-00 SHORT 0
JW704 1-216-295-00 SHORT 0 (US, CND, SP, HK)
< CONNECTOR > JW705 1-216-295-00 SHORT 0 (US, CND)
JW707 1-216-296-00 SHORT 0
CN701 1-770-167-11 CONNECTOR, FFC/FPC 19P
* CN702 1-568-941-11 PIN, CONNECTOR 3P < COIL >
CN703 1-784-776-11 CONNECTOR, FFC 15P
CN704 1-779-636-11 CONNECTOR, FFC/FPC 25P L701 1-412-029-11 INDUCTOR CHIP 10uH
CN705 1-779-967-12 SOCKET, CONNECTOR (PC BOARD) 24P L702 1-412-028-11 INDUCTOR CHIP 4.7uH
L703 1-412-032-11 INDUCTOR CHIP 100uH
CN706 1-779-568-11 CONNECTOR, FFC (LIF(NON-ZIF)) 31P L704 1-412-032-11 INDUCTOR CHIP 100uH
CN707 1-506-481-11 PIN, CONNECTOR 2P L705 1-412-032-11 INDUCTOR CHIP 100uH

< DIODE > L706 1-412-028-11 INDUCTOR CHIP 4.7uH

L707 1-412-029-11 INDUCTOR CHIP 10uH
D701 8-719-988-62 DIODE 1SS355 L708 1-412-032-11 INDUCTOR CHIP 100uH (AEP, UK)
D702 8-719-988-62 DIODE 1SS355
D703 8-719-977-03 DIODE DTZ5.6B < TRANSISTOR >
D704 8-719-422-31 DIODE MA8047-M
D705 8-719-988-62 DIODE 1SS355 Q701 8-729-202-38 TRANSISTOR 2SC3326N
Q702 8-729-202-38 TRANSISTOR 2SC3326N
D707 8-719-988-62 DIODE 1SS355 Q703 8-729-202-38 TRANSISTOR 2SC3326N
D708 8-719-988-62 DIODE 1SS355 Q704 8-729-202-38 TRANSISTOR 2SC3326N
D709 8-719-210-33 DIODE EC10DS2 Q705 8-729-424-08 TRANSISTOR UN2111
D710 8-719-988-62 DIODE 1SS355
D711 8-719-988-62 DIODE 1SS355 (AEP, UK) Q706 8-729-424-08 TRANSISTOR UN2111
Q707 8-729-421-22 TRANSISTOR UN2211
D712 8-719-988-62 DIODE 1SS355 (AEP, UK) Q708 8-729-202-38 TRANSISTOR 2SC3326N
D713 8-719-210-33 DIODE EC10DS2 Q709 8-729-202-38 TRANSISTOR 2SC3326N
D714 8-719-210-33 DIODE EC10DS2 Q710 8-729-120-28 TRANSISTOR 2SC1623-L5L6
D715 8-719-210-33 DIODE EC10DS2 (AEP, UK)
D716 8-719-210-33 DIODE EC10DS2 Q711 8-729-421-22 TRANSISTOR UN2211
Q712 8-729-421-22 TRANSISTOR UN2211
D717 8-719-210-33 DIODE EC10DS2 Q713 8-729-120-28 TRANSISTOR 2SC1623-L5L6 (AEP, UK)
D718 8-719-210-39 DIODE EC10QS-04
D719 8-719-210-39 DIODE EC10QS-04 < RESISTOR >
D720 8-719-422-49 DIODE MA8056-L
D721 8-719-210-33 DIODE EC10DS2 R701 1-216-049-11 RES, CHIP 1K 5% 1/10W
R702 1-216-049-11 RES, CHIP 1K 5% 1/10W
< FERRITE BEAD > R703 1-216-097-00 RES, CHIP 100K 5% 1/10W
R704 1-216-097-00 RES, CHIP 100K 5% 1/10W
FB702 1-500-445-21 FERRITE 0uH R705 1-216-097-00 RES, CHIP 100K 5% 1/10W
FB704 1-500-445-21 FERRITE 0uH
FB705 1-500-445-21 FERRITE 0uH R706 1-216-097-00 RES, CHIP 100K 5% 1/10W
FB706 1-500-445-21 FERRITE 0uH R707 1-216-073-00 METAL CHIP 10K 5% 1/10W
FB707 1-500-445-21 FERRITE 0uH R708 1-216-073-00 METAL CHIP 10K 5% 1/10W
R709 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
FB708 1-500-445-21 FERRITE 0uH (AEP, UK) R710 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
FB709 1-500-445-21 FERRITE 0uH
R711 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
< IC > R712 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R713 1-216-037-00 METAL CHIP 330 5% 1/10W
IC702 8-759-822-09 IC LB1641 R714 1-216-077-00 METAL CHIP 15K 5% 1/10W

– 109 –
 MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R715 1-216-077-00 METAL CHIP 15K 5% 1/10W R772 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
R773 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R716 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R774 1-216-041-00 METAL CHIP 470 5% 1/10W
R717 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R775 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
R718 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
R719 1-216-065-00 RES, CHIP 4.7K 5% 1/10W R776 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R720 1-216-073-00 METAL CHIP 10K 5% 1/10W R777 1-216-041-00 METAL CHIP 470 5% 1/10W
R778 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R721 1-216-073-00 METAL CHIP 10K 5% 1/10W R779 1-216-025-00 RES, CHIP 100 5% 1/10W
R722 1-216-097-00 RES, CHIP 100K 5% 1/10W R780 1-216-025-00 RES, CHIP 100 5% 1/10W
R723 1-216-097-00 RES, CHIP 100K 5% 1/10W
R724 1-216-049-11 RES, CHIP 1K 5% 1/10W R781 1-216-025-00 RES, CHIP 100 5% 1/10W
R725 1-216-049-11 RES, CHIP 1K 5% 1/10W R785 1-216-049-11 RES, CHIP 1K 5% 1/10W
R786 1-216-049-11 RES, CHIP 1K 5% 1/10W
R726 1-216-025-00 RES, CHIP 100 5% 1/10W R787 1-216-109-00 METAL CHIP 330K 5% 1/10W
R727 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R788 1-216-049-11 RES, CHIP 1K 5% 1/10W
R728 1-216-097-00 RES, CHIP 100K 5% 1/10W
R729 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R789 1-216-049-11 RES, CHIP 1K 5% 1/10W
R730 1-216-097-00 RES, CHIP 100K 5% 1/10W R790 1-216-049-11 RES, CHIP 1K 5% 1/10W
R791 1-216-049-11 RES, CHIP 1K 5% 1/10W
R731 1-216-121-00 RES, CHIP 1M 5% 1/10W R792 1-216-073-00 METAL CHIP 10K 5% 1/10W
R732 1-216-121-00 RES, CHIP 1M 5% 1/10W R793 1-216-081-00 METAL CHIP 22K 5% 1/10W
R733 1-216-055-00 METAL CHIP 1.8K 5% 1/10W
R734 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R794 1-216-113-00 METAL CHIP 470K 5% 1/10W
R735 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R795 1-216-113-00 METAL CHIP 470K 5% 1/10W
R796 1-216-089-00 RES, CHIP 47K 5% 1/10W
R736 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R797 1-216-089-00 RES, CHIP 47K 5% 1/10W
R737 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R798 1-216-025-00 RES, CHIP 100 5% 1/10W
R738 1-216-069-00 METAL CHIP 6.8K 5% 1/10W (AEP, UK)
R739 1-216-085-00 METAL CHIP 33K 5% 1/10W
R740 1-216-055-00 METAL CHIP 1.8K 5% 1/10W R799 1-216-073-00 METAL CHIP 10K 5% 1/10W
R800 1-216-025-00 RES, CHIP 100 5% 1/10W
R741 1-216-073-00 METAL CHIP 10K 5% 1/10W R801 1-216-025-00 RES, CHIP 100 5% 1/10W
R742 1-216-069-00 METAL CHIP 6.8K 5% 1/10W R802 1-216-025-00 RES, CHIP 100 5% 1/10W
R743 1-216-081-00 METAL CHIP 22K 5% 1/10W R803 1-216-025-00 RES, CHIP 100 5% 1/10W
R744 1-216-081-00 METAL CHIP 22K 5% 1/10W
R745 1-216-121-00 RES, CHIP 1M 5% 1/10W R804 1-216-025-00 RES, CHIP 100 5% 1/10W
R805 1-216-025-00 RES, CHIP 100 5% 1/10W
R746 1-216-101-00 METAL CHIP 150K 5% 1/10W R806 1-216-025-00 RES, CHIP 100 5% 1/10W
R747 1-216-101-00 METAL CHIP 150K 5% 1/10W R807 1-216-025-00 RES, CHIP 100 5% 1/10W
R748 1-216-121-00 RES, CHIP 1M 5% 1/10W R808 1-216-025-00 RES, CHIP 100 5% 1/10W
R749 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R750 1-216-059-00 METAL CHIP 2.7K 5% 1/10W R809 1-216-025-00 RES, CHIP 100 5% 1/10W
R810 1-216-025-00 RES, CHIP 100 5% 1/10W
R751 1-216-025-00 RES, CHIP 100 5% 1/10W R811 1-216-025-00 RES, CHIP 100 5% 1/10W
R752 1-216-025-00 RES, CHIP 100 5% 1/10W R813 1-216-073-00 METAL CHIP 10K 5% 1/10W
R753 1-216-073-00 METAL CHIP 10K 5% 1/10W R814 1-216-047-00 RES, CHIP 820 5% 1/10W
R754 1-216-025-00 RES, CHIP 100 5% 1/10W (AEP, UK)
R755 1-216-049-11 RES, CHIP 1K 5% 1/10W
R815 1-216-056-00 RES, CHIP 2K 5% 1/10W
R756 1-216-025-00 RES, CHIP 100 5% 1/10W (AEP, UK)
R757 1-216-025-00 RES, CHIP 100 5% 1/10W R816 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R758 1-216-025-00 RES, CHIP 100 5% 1/10W R817 1-216-073-00 METAL CHIP 10K 5% 1/10W
R759 1-216-073-00 METAL CHIP 10K 5% 1/10W R818 1-216-093-00 METAL CHIP 68K 5% 1/10W
R760 1-216-041-00 METAL CHIP 470 5% 1/10W (AEP, UK)
R819 1-216-100-00 RES, CHIP 130K 5% 1/10W
R761 1-216-073-00 METAL CHIP 10K 5% 1/10W (AEP, UK)
R762 1-216-041-00 METAL CHIP 470 5% 1/10W
R763 1-216-025-00 RES, CHIP 100 5% 1/10W R820 1-216-041-00 METAL CHIP 470 5% 1/10W
R764 1-216-025-00 RES, CHIP 100 5% 1/10W R821 1-216-073-00 RES, CHIP 10K 5% 1/10W
R765 1-216-025-00 RES, CHIP 100 5% 1/10W (AEP, UK)
R822 1-216-073-00 RES, CHIP 10K 5% 1/10W
R766 1-216-025-00 RES, CHIP 100 5% 1/10W (AEP, UK)
R767 1-216-041-00 METAL CHIP 470 5% 1/10W R823 1-216-049-11 RES, CHIP 1K 5% 1/10W
R768 1-216-073-00 METAL CHIP 10K 5% 1/10W (AEP, UK)
R769 1-216-025-00 RES, CHIP 100 5% 1/10W R824 1-218-282-11 RES, CHIP 22 5% 1/2W
R770 1-216-025-00 RES, CHIP 100 5% 1/10W (AEP, UK)

R771 1-216-025-00 RES, CHIP 100 5% 1/10W R825 1-216-061-00 METAL CHIP 3.3K 5% 1/10W

– 110 –
 MAIN MOTOR PANEL
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R826 1-216-049-11 RES, CHIP 1K 5% 1/10W < CONNECTOR >
R827 1-216-073-00 METAL CHIP 10K 5% 1/10W
R828 1-216-081-00 METAL CHIP 22K 5% 1/10W CN901 1-779-969-11 PLUG, CONNECTOR (PC BOARD) 24P
R829 1-216-049-11 RES, CHIP 1K 5% 1/10W
< DIODE >
R830 1-216-041-00 METAL CHIP 470 5% 1/10W
R831 1-216-121-00 METAL CHIP 1M 5% 1/10W D901 8-719-977-03 DIODE DTZ5.6B
D902 8-719-069-45 LED SELU5E23C-TP15 (FOR ILLUMINATION)
< VIBRATOR > D903 8-719-057-29 LED SML78423C-TP15 (MD, ^)
D905 8-719-058-04 LED SEL5223S-TP15 (REC)
X701 1-567-098-41 VIBRATOR, CRYSTAL (32.768kHz) D907 8-719-057-29 LED SML78423C-TP15 (CD, ^)
X702 1-760-489-11 VIBRATOR, CERAMIC (5MHz)
X703 1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz) (AEP, UK) < FLUORESCENT INDICATOR TUBE >
************************************************************
FL901 1-517-687-11 INDICATOR TUBE, FLUORESCENT
* 1-671-428-11 MOTOR BOARD
************* < IC >

< CAPACITOR > IC901 8-759-297-23 IC M66004M8FP

IC902 8-759-459-83 IC NJL55H400A
C110 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
************************************************************ < COIL >

* A-4417-231-A PANEL BOARD, COMPLETE L901 1-412-029-11 INDUCTOR CHIP 10uH

********************** L902 1-412-029-11 INDUCTOR CHIP 10uH

* 4-993-866-01 HOLDER (FL) < TRANSISTOR >

< CAPACITOR > Q901 8-729-120-28 TRANSISTOR 2SC1623-L5L6

Q902 8-729-120-28 TRANSISTOR 2SC1623-L5L6
C901 1-126-160-11 ELECT 1uF 20% 50V Q903 8-729-424-08 TRANSISTOR UN2111
C902 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V Q904 8-729-424-08 TRANSISTOR UN2111
C903 1-163-005-11 CERAMIC CHIP 470PF 10% 50V Q905 8-729-424-08 TRANSISTOR UN2111
C904 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C905 1-163-005-11 CERAMIC CHIP 470PF 10% 50V Q906 8-729-424-08 TRANSISTOR UN2111
Q907 8-729-424-08 TRANSISTOR UN2111
C906 1-124-261-00 ELECT 10uF 20% 50V Q908 8-729-424-08 TRANSISTOR UN2111
C907 1-124-234-00 ELECT 22uF 20% 16V Q909 8-729-424-08 TRANSISTOR UN2111
C908 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C909 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V < RESISTOR >
C910 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
R901 1-216-097-00 RES, CHIP 100K 5% 1/10W
C911 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R902 1-216-097-00 RES, CHIP 100K 5% 1/10W
C912 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R903 1-216-049-11 RES, CHIP 1K 5% 1/10W
C913 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R904 1-216-049-11 RES, CHIP 1K 5% 1/10W
C914 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R905 1-216-097-00 RES, CHIP 100K 5% 1/10W
C915 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
R906 1-216-085-00 METAL CHIP 33K 5% 1/10W
C916 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R907 1-216-049-11 RES, CHIP 1K 5% 1/10W
C917 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R908 1-216-049-11 RES, CHIP 1K 5% 1/10W
C918 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R909 1-216-049-11 RES, CHIP 1K 5% 1/10W
C919 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R910 1-216-049-11 RES, CHIP 1K 5% 1/10W
C920 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
R913 1-216-025-00 RES, CHIP 100 5% 1/10W
C921 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V R914 1-216-025-00 RES, CHIP 100 5% 1/10W
C922 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R915 1-216-025-00 RES, CHIP 100 5% 1/10W
C923 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R916 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
C924 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R917 1-216-033-00 METAL CHIP 220 5% 1/10W
C925 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
R918 1-216-033-00 METAL CHIP 220 5% 1/10W
C926 1-163-001-11 CERAMIC CHIP 220PF 10% 50V R919 1-216-025-00 RES, CHIP 100 5% 1/10W
C927 1-163-005-11 CERAMIC CHIP 470PF 10% 50V R920 1-216-025-00 RES, CHIP 100 5% 1/10W
C928 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V R922 1-216-025-00 RES, CHIP 100 5% 1/10W
C929 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V R924 1-216-025-00 RES, CHIP 100 5% 1/10W
C930 1-126-160-11 ELECT 1uF 20% 50V
R925 1-216-029-00 METAL CHIP 150 5% 1/10W
C931 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V R926 1-216-041-00 METAL CHIP 470 5% 1/10W
C933 1-124-589-11 ELECT 47uF 20% 16V R927 1-216-041-00 METAL CHIP 470 5% 1/10W
C934 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V R928 1-216-045-00 METAL CHIP 680 5% 1/10W

– 111 –
 PANEL POWER
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R929 1-216-045-00 METAL CHIP 680 5% 1/10W C522 1-126-916-11 ELECT 1000uF 20% 6.3V
C523 1-126-933-11 ELECT 100uF 20% 16V
R930 1-216-037-00 METAL CHIP 330 5% 1/10W C524 1-126-933-11 ELECT 100uF 20% 16V
R931 1-216-049-11 RES, CHIP 1K 5% 1/10W C525 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
R932 1-216-049-11 RES, CHIP 1K 5% 1/10W C527 1-126-933-11 ELECT 100uF 20% 16V
R933 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R934 1-216-053-00 METAL CHIP 1.5K 5% 1/10W C528 1-163-021-11 CERAMIC CHIP 0.01uF 10% 50V
C530 1-126-933-11 ELECT 100uF 20% 16V
R936 1-216-057-00 METAL CHIP 2.2K 5% 1/10W C531 1-126-934-11 ELECT 220uF 20% 16V
R937 1-216-057-00 METAL CHIP 2.2K 5% 1/10W C532 1-126-933-11 ELECT 100uF 20% 16V
R938 1-216-001-00 METAL CHIP 10 5% 1/10W C533 1-126-933-11 ELECT 100uF 20% 16V
R939 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
R940 1-216-029-00 METAL CHIP 150 5% 1/10W C538 1-126-965-11 ELECT 22uF 20% 50V
C544 1-126-963-11 ELECT 4.7uF 20% 50V
R941 1-216-075-00 METAL CHIP 12K 5% 1/10W C545 1-126-963-11 ELECT 4.7uF 20% 50V
R944 1-216-029-00 METAL CHIP 150 5% 1/10W C548 1-126-959-11 ELECT 0.47uF 20% 50V
R945 1-216-029-00 METAL CHIP 150 5% 1/10W C549 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V

< SWITCH > C550 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C551 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
S901 1-762-875-21 SWITCH, KEYBOARD (FUNCTION) C552 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
S902 1-762-875-21 SWITCH, KEYBOARD (CD, p) C553 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
S903 1-762-875-21 SWITCH, KEYBOARD (I/u) C554 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
S904 1-762-875-21 SWITCH, KEYBOARD (CD/MD, ) +)
S905 1-762-875-21 SWITCH, KEYBOARD (CD, ^) C555 1-126-964-11 ELECT 10uF 20% 50V

S908 1-762-875-21 SWITCH, KEYBOARD (CD/MD, = 0) < CONNECTOR >

S909 1-762-875-21 SWITCH, KEYBOARD (MD, p)
S910 1-762-875-21 SWITCH, KEYBOARD (REC) * CN501 1-564-915-11 PIN, CONNECTOR 7P
S911 1-762-875-21 SWITCH, KEYBOARD (MD, ^) CN502 1-779-568-11 CONNECTOR,FFC(LIF(NON-ZIF))31P
S912 1-762-875-21 SWITCH, KEYBOARD (CD-MD SYNC) CN503 1-784-041-41 CONNECTOR, BOARD TO BOARD 9P
* CN504 1-564-518-11 PLUG, CONNECTOR 3P
S913 1-762-875-21 SWITCH, KEYBOARD (6 (MD))
S914 1-762-875-21 SWITCH, KEYBOARD (VOLUME, +) < DIODE >
S915 1-762-875-21 SWITCH, KEYBOARD (VOLUME, –)
************************************************************ D501 8-719-988-62 DIODE 1SS355
D502 8-719-988-62 DIODE 1SS355
* A-4417-232-A POWER BOARD, COMPLETE D503 8-719-210-33 DIODE EC10DS2
*********************** D504 8-719-210-33 DIODE EC10DS2
D505 8-719-210-33 DIODE EC10DS2
1-533-293-11 FUSE HOLDER
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S D506 8-719-988-62 DIODE 1SS355
D507 8-719-988-62 DIODE 1SS355
< CAPACITOR > D508 8-719-018-12 DIODE MA8330-L-TX
D509 8-719-025-03 DIODE RBA-402-SL
C501 1-126-968-11 ELECT 100uF 20% 50V D510 8-719-210-33 DIODE EC10DS2
C502 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C503 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V D511 8-719-210-33 DIODE EC10DS2
C504 1-126-968-11 ELECT 100uF 20% 50V D512 8-719-210-33 DIODE EC10DS2
C505 1-126-968-11 ELECT 100uF 20% 50V D513 8-719-210-33 DIODE EC10DS2
D518 8-719-420-14 DIODE MA8082-M
C506 1-126-964-11 ELECT 10uF 20% 50V D519 8-719-988-62 DIODE 1SS355
C507 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V
C508 1-126-964-11 ELECT 10uF 20% 50V D520 8-719-017-86 DIODE MA8140-M-TX
C509 1-115-339-11 CERAMIC CHIP 0.1uF 10% 50V D521 8-719-988-62 DIODE 1SS355
C510 1-126-968-11 ELECT 100uF 20% 50V D524 8-719-210-33 DIODE EC10DS2
D525 8-719-210-33 DIODE EC10DS2
C511 1-117-850-11 ELECT 15000uF 20% 16V D526 8-719-422-76 DIODE MA8075-M
C512 1-126-042-11 ELECT 3300uF 20% 35V
C513 1-126-042-11 ELECT 3300uF 20% 35V D527 8-719-988-62 DIODE 1SS355
C514 1-126-964-11 ELECT 10uF 20% 50V
C515 1-126-964-11 ELECT 10uF 20% 50V < FUSE >

C516 1-126-960-11 ELECT 1uF 20% 50V ! F501 1-532-504-51 FUSE (T4AL/250V) (AEP, UK, SP, HK)
C517 1-126-964-11 ELECT 10uF 20% 50V ! F501 1-576-108-11 FUSE (4A/125V) (US, CND)
C518 1-126-964-11 ELECT 10uF 20% 50V ! F502 1-532-504-51 FUSE (T4AL/250V) (AEP, UK, SP, HK)
C519 1-126-933-11 ELECT 100uF 20% 16V ! F502 1-576-108-11 FUSE (4A/125V) (US, CND)
C520 1-126-952-11 ELECT 1000uF 20% 35V ! F503 1-532-464-51 FUSE (T2.5AL/250V) (AEP, UK, SP, HK)

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
– 112 – ber specified. portant le numéro spécifié.
 POWER SENSOR SW
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! F503 1-576-105-11 FUSE (2.5A/250V) (US, CND) ! R536 1-249-387-11 CARBON 3.3 5% 1/4W F

< GROUND TERMINAL > R537 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R538 1-216-091-00 METAL CHIP 56K 5% 1/10W
EPT501 1-537-771-21 TERMINAL BOARD, GROUND R539 1-216-089-00 RES, CHIP 47K 5% 1/10W
R540 1-216-077-00 METAL CHIP 15K 5% 1/10W
< IC > R541 1-216-071-00 METAL CHIP 8.2K 5% 1/10W

IC501 8-759-708-05 IC NJM78L05A R542 1-216-121-00 RES, CHIP 1M 5% 1/10W

IC502 8-759-445-59 IC BA033T R543 1-216-077-00 METAL CHIP 15K 5% 1/10W
IC503 8-759-158-62 IC TA78057S R545 1-218-232-91 RES, CHIP 4.7 10% 1/2W
IC504 8-759-604-86 IC M5F7807L R546 1-218-232-91 RES, CHIP 4.7 10% 1/2W
IC505 8-759-231-58 IC TA7812S R548 1-220-250-11 RES, CHIP 10 5% 1/2W

< COIL > R549 1-220-250-11 RES, CHIP 10 5% 1/2W

L501 1-420-872-00 COIL, AIR-CORE < RELAY >

L502 1-420-872-00 COIL, AIR-CORE
RY501 1-515-833-11 RELAY
< TRANSISTOR > ************************************************************

Q503 8-729-140-97 TRANSISTOR 2SB734-34 * 1-671-427-11 SENSOR BOARD

Q504 8-729-424-59 TRANSISTOR UN2212 *************
Q505 8-729-424-12 TRANSISTOR UN2112
Q506 8-729-120-28 TRANSISTOR 2SC1623-L5L6 < SWITCH >
Q507 8-729-118-01 TRANSISTOR 2SB1116
S104 1-571-300-21 SWITCH, ROTARY (DISC DETECT)
Q508 8-729-424-59 TRANSISTOR UN2212 ************************************************************
Q509 8-729-111-29 TRANSISTOR 2SD1616A-K
Q510 8-729-120-28 TRANSISTOR 2SC1623-L5L6 * 1-667-719-11 SW BOARD
Q511 8-729-120-28 TRANSISTOR 2SC1623-L5L6 *********
Q512 8-729-424-12 TRANSISTOR UN2112
< CONNECTOR >
Q514 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q516 8-729-120-28 TRANSISTOR 2SC1623-L5L6 CN601 1-770-697-11 CONNECTOR, FFC/FPC 14P
Q518 8-729-216-22 TRANSISTOR 2SA1162-G CN602 1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P
Q519 8-729-021-82 TRANSISTOR 2SD2396K CN603 1-778-638-21 PIN, CONNECTOR (PC BOARD) 2P
Q520 8-729-424-59 TRANSISTOR UN2212
< SWITCH >
< RESISTOR >
S681 1-572-467-61 SWITCH, PUSH (1 KEY) (LIMIT IN)
R458 1-216-061-00 METAL CHIP 3.3K 5% 1/10W S682 1-692-377-31 SWITCH, PUSH (1 KEY) (REFLECT)
! R504 1-249-394-11 CARBON 12 5% 1/4W F S683 1-692-847-21 SWITCH, PUSH (1 KEY) (PROTECT)
R505 1-216-065-00 RES, CHIP 4.7K 5% 1/10W S685 1-572-467-61 SWITCH, PUSH (1 KEY) (CHUCKING IN)
R506 1-216-065-00 RES, CHIP 4.7K 5% 1/10W S686 1-762-621-21 SWITCH, PUSH (1 KEY) (PACK OUT)
R507 1-216-065-00 RES, CHIP 4.7K 5% 1/10W
S687 1-572-688-11 SWITCH, PUSH (1 KEY) (PB POSITION)
R508 1-216-081-00 RES, CHIP 22K 5% 1/10W S688 1-762-621-21 SWITCH, PUSH (1 KEY) (REC POSITION)
R509 1-216-097-00 RES, CHIP 100K 5% 1/10W ************************************************************
R510 1-216-073-00 METAL CHIP 10K 5% 1/10W
R511 1-216-057-00 METAL CHIP 2.2K 5% 1/10W MISCELLANEOUS
R512 1-216-033-00 METAL CHIP 220 5% 1/10W **************

R513 1-216-047-00 RES, CHIP 820 5% 1/10W 154 1-790-106-11 WIRE (FLAT TYPE) (31 CORE)
! R514 1-249-397-11 CARBON 22 5% 1/4W F 155 1-775-170-11 WIRE (FLAT TYPE) (19 CORE)
R515 1-216-049-11 RES, CHIP 1K 5% 1/10W ! 163 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (HK)
R516 1-216-091-00 METAL CHIP 56K 5% 1/10W ! 164 1-575-651-21 CORD, POWER (AEP, SP, HK)
R517 1-216-049-11 RES, CHIP 1K 5% 1/10W ! 164 1-696-571-11 CORD, POWER (UK)

R518 1-216-057-00 METAL CHIP 2.2K 5% 1/10W ! 164 1-783-531-31 CORD, POWER (US, CND)
R519 1-216-081-00 METAL CHIP 22K 5% 1/10W ! 165 1-569-008-21 ADAPTOR, CONVERSION 2P (SP)
R524 1-216-081-00 METAL CHIP 22K 5% 1/10W 166 1-773-009-11 WIRE (FLAT TYPE) (15 CORE)
R525 1-216-073-00 METAL CHIP 10K 5% 1/10W 167 1-693-407-21 TUNER (US, CND)
R530 1-216-073-00 METAL CHIP 10K 5% 1/10W 167 1-693-409-21 TUNER (AEP, UK, SP, HK)

R531 1-216-073-00 METAL CHIP 10K 5% 1/10W 170 1-790-105-11 WIRE (FLAT TYPE) (25 CORE)
R532 1-216-093-00 RES, CHIP 68K 5% 1/10W 202 1-660-966-11 OP RELAY FLEXIBLE BOARD
R534 1-216-097-00 RES, CHIP 100K 5% 1/10W 203 1-782-683-11 WIRE (FLAT TYPE) (14 CORE)
R535 1-216-065-00 RES, CHIP 4.7K 5% 1/10W ! 251 8-583-028-02 OPTICAL PICK-UP KMS-260A/J1N (for MD)

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.
– 113 –
HCD-MD1EX

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
! 305 8-848-379-31 OPTICAL PICK-UP KSS-213B/K-N (for CD)

306 1-769-069-11 WIRE (FLAT TYPE) (16 CORE)

HR901 1-500-396-11 HEAD, OVER LIGHT (RF325-74A)
M101 X-4942-405-1 BASE (OUTSART) ASSY (SPINDLE) (for CD)
M102 X-4917-504-1 MOTOR ASSY (SLED) (for CD)
M103 A-4411-278-A MOTOR ASSY (CD LID OPEN/CLOSE)

M501 1-698-997-11 FAN, D.C.

M901 A-4672-135-A MOTOR ASSY, SPINDLE (for MD)
M902 A-4672-133-A MOTOR ASSY, SLED (for MD)
M903 A-4672-134-A MOTOR ASSY, LOADING (for MD)
! T901 1-433-472-11 TRANSFORMER, POWER (US, CND)

! T901 1-433-473-11 TRANSFORMER, POWER (AEP, UK)

! T901 1-433-474-11 TRANSFORMER, POWER (SP, HK)
************************************************************

**************
HARDWARE LIST
**************

#1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S

#2 7-685-791-09 SCREW +PTT 2.6X5 (S)
#3 7-685-850-04 SCREW +BVTT 2X3 (S)
#4 7-685-871-01 SCREW +BVTT 3X6 (S)
#5 7-685-880-09 SCREW +BVTT 4X6 (S)

#6 7-685-851-04 SCREW +BVTT 2X4 (S)

#7 7-627-552-27 SCREW,PRECISION +P 1.7X2
#8 7-627-852-28 +P 1.7X3
#9 7-627-553-17 PRECISION SCREW +P 2X2 TYPE 3
#10 7-621-775-00 SCREW +B 2.6X3

The components identified by Les composants identifiés par une

mark ! or dotted line with marque ! sont critiques pour la
mark ! are critical for safety. sécurité.
Replace only with part num- Ne les remplacer que par une pièce
ber specified. portant le numéro spécifié.

Sony Corporation 98H0586-1

Printed in Japan © 1998. 8
9-922-950-11 Home A&V Products Company Published by Quality Assurance Dept.
– 114 – (Shibaura)
 HCD-MD1EX

MEMO

115
HCD-MD1EX

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.1 2001.02 Correction of Motor (M902, M903) (SPM-01004)

1.0 1998.08 New