Nr.
0628
Rev 1.3
Data: 09/2020
PREPARATION OF THE DIAGPROG4 FOR WORK.
BEFORE STARTING OF THE WORK IT IS REQUIRED TO:
Update the DiagProg4 to the latest software version and download the SW_Files.
Use the Diagprog4 Manager program and perform the maintenance of your device.
Diagprog4 Manager Diagprog4 Manager Diagprog4 Manager
Software Update Download SW_Files
Check the integrity of SW_Files files on the SD card.
After starting the program, the DiagProg4 will automatically check the available SW_Files files which will be required
during the program
programming. The plugging to the programmed module is not required.
In case of appearing of the message:
Perform the download
downloading of the missing files. To make it, use the Diagprog4 Manager or connect the DiagProg4 to WiFi
and run the built-in
built in Maintenance
Maintenance-Service function.
function
For the verification of the completion of the above process, simply open the program again.
If the device does not inform us about the lack of files, the device is properly prepared for work.
Nr. 0628
Rev 1.3
Data: 09/2020
SOFTWARE CABLE
REPAIR
D3
PROGRAMMING
151 C21
TESTING
C12
FEATURES DESCRIPTIONS
Identification Module identification
(VIN
VIN number, part number, software number)
number
Display Test Display test of the odometer module
Sound Test Sound test of the odometer module
Indicator Test Indicator test of the odometer module
Check version - OBDII Checking the software version and part number by OBDII
Prepare FLASH - OBDII Prepare FLASH of odometer by OBDII
(DiagProg4
DiagProg4 performs a full EEPROM data backup – 95C128 – on SD card)
Read password from Flash by C21 Read security key from flash by C21 cable
Write odometer by C12* Writing of the KM values to the module by C12 cable*
cable
Flash – OBDII Software update in the odometer module
Reset Disconnecting the power supply from the module
* IN CASE OF PROGRAMMING MILEAGE OR HOURS OF OPERATION, THE SOFTWARE MAY BE USED SOLELY FOR REPAIR
REPAIR-RELATED
RELATED PURPOSES. HOWEVER, IN SOME COUNTRIES ANY
CHANGES TO ODOMETER (CLOCK) READING OR TAMPERING WITH THE MILEAGE ACCURACY SHALL BE FORBIDDEN UNDER PENALTY.
PURSUANT TO ART. 306a OF THE POLISH PENAL CODE, WHOEVER ALTERS ODOMETERS OF MOTOR VEHICLES OR TAMPERS WITH THE MILEAGE ACCURACY
ACCURA CY SHALL BE SUBJECT TO THE
PENALTY OF DEPRIVATION OF LIBERTY FROM 3 MONTHS UP TO 5 YEARS. WHOEVER COMMISSIONS A THIRD PARTY TO PE
PERFORM
RFORM THE ABOVE-MENTIONED
ABOVE MENTIONED ACT SHALL BE SUBJECT TO
THE SAME PENALTY.
Nr. 0628
Rev 1.3
Data: 09/2020
FEATURES DESCRIPTIONS
Erasing DTC’s Erasing DTC’s from all modules in a vehicle
Read EEPROM Reading EEPROM memory
Edit EEPROM Editing EEPROM memory
Load file to buffer Loading file to buffer from microSD card
Save buffer to file Saving buffer to file on microSD card
Nr. 0628
Rev 1.3
Data: 09/2020
THE CURRENT LIST OF SUPPORTED MODULES
LIST OF THE SUPPORTED VERSIONS
PART NUMBER PART NUMBER
3G0920640 5G0920851C
3G0920641 5G0920861
3G0920650 5G0920861A
3G0920651 5G0920861B
3G0920740 5G0920861C
3G0920741 5G0920871
3G0920750 5G0920871A
3G0920751 5G0920871B
3G0920940 5G0920871C
3G0920941 5G0920951
3G0920950 5G0920951A
3G0920951 5G0920961
510920850 5G0920961A
510920850A 5G0920971
510920950 5G0920971A
510920950A 5G0920971B
5E0920780 5G0920971C
5E0920781 5G1920640
5E0920851A 5G1920641
5E0920851E 5G1920650
5E0920861A 5G1920651
5E0920861E 5G1920740
5E0920951A 5G1920741
5E0920951E 5G1920750
5E0920961A 5G1920751
5E0920961E 5G1920940
5E0920980 5G1920941
5E0920981 5G1920950
5G0920640 5G1920951
5G0920851 5GG920640
5G0920851A
5G0920851B
Nr. 0628
Rev 1.3
Data: 09/2020
C21 Cable
MODULE CONNECTION
FIRST VERSION
Nr. 0628
Rev 1.3
Data: 09/2020
C21 Cable
MODULE CONNECTION
SECOND VERSION
Nr. 0628
Rev 1.3
Data: 09/2020
C21 Cable
MODULE CONNECTION
THIRD VERSION
Nr. 0628
Rev 1.3
Data: 09/2020
MODULE CONNECTION
C12 Cable
Nr. 0628
Rev 1.3
Data: 09/2020
Software update in the odometer module - Flash – OBDII
Upgrade to the latest version
Flash – OBDII Software update in the odometer module
It's
t's recommended to turn on the hazard lights
during the Software Update process
SOFTWARE UPDATE - OPTIONAL MODULE CONNECTION
DiagProg4 Settings
- TOOLS → EXTERNAL UNIT POWER→ ON
Nr. 0628
Rev 1.3
Data: 09/2020
LIST OF ERROR CODES
ERROR CODES CAUSE / DESCRIPTION
ERR_UNKNOWN_VERSION Unknown version – version not supported.
ERR_JTAG_DISABLED - Incorrect module connection,
- Incorrect FLASH preparation, repeat FLASH
preparation.
ERR_VAL_NOT_FOUND Incorrect reading security key from FLASH
This is not platform MQBAB - (Johnson This module is not an MQBAB platform
Controls) dashboard ! (Johnson Controls) – version not supported.
Ignition Key missing There’s no key in the ignition.
ERR_FILE_OPEN There's no SD card in DiagProg4 or the SD
card is damaged.
Nr. 0628
Rev 1.3
Data: 09/2020
LEGAL DISCLAIMER
It is forbidden to use DiagProg4 device, software for this device, information contained in this document and any other Elprosys
products for purposes which are illegal or prohibited in any other way. Elprosys and the company’s management board shall not be
liable for the results of the use of the DiagProg4 device, software, information contained in this document and any other Elprosys
products for purposes which are illegal or prohibited in any other way. Copying, redistribution, publishing, dissemination, sale,
giving access to or making use in any other way of the whole or part of the software and data contained in this document are
forbidden. Elprosys may introduce improvements or modifications of products on offer and their documentation as well instruction
manuals at any time without a prior notice. Any and all trademarks, product names and information set forth in the document are
the property of the Elprosys company and are protected by the law. A User is required to respect intellectual property rights of
resources contained in the document.
DIAGPROG4 TERMS OF USE
THE ELPROSYS COMPANY SHALL NOT BE HELD LIABLE FOR ANY ILLEGAL USE OF SOFTWARE AND HARDWARE. ANY
PURCHASED SOFTWARE AND HARDWARE SHALL BE USED FOR PURPOSES CONSISTENT WITH LEGAL PROVISIONS.
IN CASE OF PROGRAMMING MILEAGE OR HOURS OF OPERATION, THE SOFTWARE MAY BE USED SOLELY FOR REPAIR-
RELATED PURPOSES. HOWEVER, IN SOME COUNTRIES ANY CHANGES TO ODOMETER (CLOCK) READING OR TAMPERING
WITH THE MILEAGE ACCURACY SHALL BE FORBIDDEN UNDER PENALTY.
PURSUANT TO ART. 306a OF THE POLISH PENAL CODE, WHOEVER ALTERS ODOMETERS OF MOTOR VEHICLES OR
TAMPERS WITH THE MILEAGE ACCURACY SHALL BE SUBJECT TO THE PENALTY OF DEPRIVATION OF LIBERTY FROM 3
MONTHS UP TO 5 YEARS. WHOEVER COMMISSIONS A THIRD PARTY TO PERFORM THE ABOVE-MENTIONED ACT
SHALL BE SUBJECT TO THE SAME PENALTY.
IT SHALL BE FORBIDDEN, IN PARTICULAR, TO USE THE PURCHASED SOFTWARE OR PERFORM WITH ITS HELP ANY
CHANGES TO THE CAR CLOCKS, COMPUTERS, IMMOBILIZERS ETC., THAT MAY BE IN BREACH OF THE LAW OR BE
INDIRECTLY USED FOR CRIMINAL PURPOSES.
BY PURCHASING THE SOFTWARE, THE BUYER ACCEPTS PERSONAL LIABILITY FOR LEGAL USE OF THE SOFTWARE. THUS,
THE ELPROSYS COMPANY SHALL BE RELEASED FROM ANY LIABILITY FOR THE ILLEGAL USE OF THE SOFTWARE.
THE USER CONFIRMS TO HAVE READ THE PROVISIONS OF THE SOFTWARE LICENCE AGREEMENT AVAILABLE AT
WWW.ELPROSYS.COM/AGREEMENT/INDEX.HTML, AND TO HAVE ACCEPTED IT IN FULL.
