DRRM 31
DRRM 31
SERVICE MANUAL
MODEL DRR-M31
STEREO CASSETTE DECK
Some illustrations using in this service manual are slightly different from the actual set.
SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
2
DRR-M31 3
DISASSEMBLY
(Follow the procedure below in reverse order when reassembling)
1. TOP COVER
(1) Remove 2 screws ① fixing from the both
sides.
(2) Remove 5 screws ② fixing to the Rear Plate,
then detach the Top Cover in the arrow di-
rection .
2. FRONT PANEL
(1) Disconnect 1 HCU joiner coming from the
front P.W.B.
(2) Remove 4 screws ③ fixing the Front Panel at
the bottom.
(3) Whil releasing 2 hooks, detach the Front
Panel.
3
DRR-M31 4
4. REAR PLATE
(1) Pull up the Power Cord together with the cord
bush to disengage from the Rear Plate.
(2) Remove 3 screws ⑤ fixing the 4P pin jack and
AC outlet respectively.
(3) Remove 1 screw ⑥ , and detach the Rear Plate.
5. MAIN P.W.B.
(1) Remove 1 screw ⑦ fixing the AMP P.W.B.
(2) Pull up the AMP P.W.B. as shown in the arrow
direction, and disconnect 2 connectors.
Connector
(3) Remove 4 screws ⑧ fixing the Main P.W.B.
(4) Release 3 pieces of P.W.B. spacers.
(5) Disconnect the connector from the Trans Unit.
(6) Take off the Main P.W.B.
AMP
6. DISPLAY P.W.B.
(1) Pull out the knob (E).
(2) Remove the nut and washer ⑨ for the rotary
switch.
(3) Remove 9 screws ⑩ .
(4) Take off the Display P.W.B.
4
DRR-M31 5
ADJUSTMENTS
ADJUSTMENTS
Adjusting and Checking the Mechanism Section
A-BEX TCC-153
2.45 3.92N
(250 400g)
REC/PB HEAD
5
DRR-M31 6
6
DRR-M31 7
3. Azimuth Adjustment
(1) Connect an electronic voltmeter to the Line Out
terminal, and set Test tape MTT-114N into the Unit.
(2) Playback FWD side,and adjust the azimuth screw A
so as to get maximum indication on the voltmeter, PB Amp
then make the same adjustment with the screw B for LINE OUT
V. V
REV side.
(3) Readjust if the output level difference exceeds 2dB
after adjustment, and also confirm that the phase
difference in the both channels is within ±45 . MTT-114N
Note: In order to prevent the backlash of the azimuth
screw, end in the clockwise rotation.
A B
MTT-150
7
DRR-M31 8
ADJUSTMENT POINTS
LINE IN LINE OUT
JK301
Rch
R/P Level Adjust
VR304
Lch
VR303
Lch
PB GAIN Adjust
VR301
Rch
VR302
MAIN P.W.B
(Deck Mecha.)
Lch
VR306
Rch
VR305
8
DRR-M31 9
BLOCK DIAGRAM
PLAYBACK
PLAY BACK LEVEL ADJ.
TU201,202 AMP
PB IN IC203 PB OUT ( Lch )
R/P HEAD
LINE OUT
VR203,204 REC OUT DOLBY IC REC IN IC204
IC201 LEVEL DETECT AMP ( A/D ) TP215,216
+7V TR206,207 TR208,209
LINE MUTE
R/P
SWITCHING
MPX TR317
FILTER IC205 μCOM ( LINE MUTE OUT )
TR203 NOR μCOM A/D INPUT
R/P TR201 LINE IN
+7V
μCOM L201,202 AUTO LEVEL CONTROL
-7V R/P TR212
TR213,214
-7V TR211
D.RP
TR509 ( μCOM )
BIAS ADJ.
VR201,202 μCOM
R. MUTE
+B
L203
DOLBY IC
TR204 -7V PB OUT ( Rch )
E. HEAD
TR205
+5V P. OFF
TR303 μCOM. SCK JK301
CrO2 μCOM
μCOM NOR BIAS
TR304
R. MUTE +12V
+5V
IC304
+7V
CAPSTAN
MOTOR TR502 TR326
M +12V KEY
TR501
SOL & LED TR324
TR323
+5V P. ON
IC501 AC PLUG
CrO2 SW
+5V
TR506 NOR
TR504 TR505
μCOM -7V
( LD405
Green (
NOR SW
TR507 CrO2 TR325
F. REC
R. REC T101
μCOM TR510
HALF POWER TRANS
TR327
RESET P. OFF
MODE SOLENOID MOTOR
μCOM. REEL PULSE μCOM μCOM
TR328
HALL IC DISTLAY PWB
9
DRR-M31 10
SEMICONDUCTORS
IC's
µ
µPD78044FGF (IC203)
P114 / FIP22
P115 / FIP23
P116 / FIP24
P117 / FIP25
P120 / FIP26
P121 / FIP27
P122 / FIP28
P123 / FIP29
P124 / FIP30
P125 / FIP31
P126 / FIP32
P127 / FIP33
P00 / INTP0
P01 / INTP1
P02 / INTP2
P03 / INTP3
P30 / TO0
P31 / TO1
P32 / TO2
IC (VPP)
VDD
P70
P71
P72
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
P23 / STB
VDD
P24 / BUSY
AVSS
P27 / SCK0
P26 / SO0
P25 / SI0
P22 / SCK1
P20 / SI1
P94 / FIP6
P93 / FIP5
P92 / FIP4
P91 / FIP3
P90 / FIP2
P81 / FIP1
P80 / FIP0
P21 / SO1
RESET
P17 / ANI7
P16 / ANI6
P15 / ANI5
P14 / ANI4
P74
P73
10
DRR-M31 11
Pin
Port Name Symbol I/O Ini Function
No.
26 P12/ANI2 TEST I Hi-z Board check mode input terminal
27 P11/ANI1 AD-L I Hi-z Audio signal L-ch
28 P10/ANI0 AD-R I Hi-z Audio signal R-ch
29 AVDD AVDD Analog power (+5v)
30 AVREF AVREF Analog refernce voltage
31 P04/XT1 I Hi-z Not used: either pull up/down
32 XT2 XT2 O Not used: open
33 VSS VSS GND
34 X1 X1 I Main systemclock input
35 X2 X2 O Main systemclock output
36 P37 O Hi-z Not used open
37 P36/BUZ O Hi-z Not used open
38 P35/PCL O Hi-z Not used open
39 P34/TI2 SOL O Hi-z Solenoid control signal
40 P33/TI1 MOT O Hi-z Motor control signal
41 P32/TO2 MODESW I Hi-z Deck mecka mode SW input signal (H: stop)
42 P31/TO1 LOADOUT I Hi-z Loader open input signal
43 P30/TO0 LOADIN I Hi-z Loader close input signal
44 P03/INTP3 STANBY I Hi-z Power shut off detection signal (H: normal,L: shut off)
45 P02/INTP2 REEL I Hi-z Supply reel pulse input signal
46 P01/INTP1 I Hi-z Not used
47 P00/INTP0 SERINT I Hi-z DENON BUS communicate intervention signal
48 IC IC Internal connection terminal,connect to Vss
49 P72 O Hi-z Not used: open
50 P71 O Hi-z Not used: open
51 P70 O Hi-z Not used: open
52 VDD VDD Hi-z 5V power
53 P127/FIP33 L MUTE O Hi-z Line mute control signal (L: mute)
54 P126/FIP32 DOLBY O Hi-z Not used: DOLBY switching signal (H: off)
55 P125/FIP31 DOLB/C O Hi-z Not used: DOLBY B/C switching signal (H: B)
56 P124/FIP30 DOLR/P O Hi-z DOLBY REC /PB switching signal (L: PB)
57 P123/FIP29 MPXFIL O Hi-z Not used : MPX filter control signal
58 P122/FIP28 O Hi-z Not used: open
59 P121/FIP27 BIAS O Hi-z Bias control signal (H: OSC)
60 P120/FIP26 O Hi-z Not used: open
61 P117/FIP25 O Hi-z Not used: open
62 P116/FIP24 O Hi-z Not used: open
63 P115/FIP23 O Hi-z Not used: open
64 P114/FIP22 O Hi-z Not used: open
65 P113/FIP21 O Hi-z Not used: open
66 P112/FIP20 O Hi-z Not used: open
67 P111/FIP19 O Hi-z Not used: open
68 P110/FIP18 O Hi-z Not used: open
69 P107/FIP17 O Hi-z Not used: open
70 P106/FIP16 O Hi-z Not used: open
71 VLOAD VLOAD connect to GND
72 P105/FIP15 O Hi-z connect to GND
73 P104/FIP14 O Hi-z connect to GND
74 P103/FIP13 O Hi-z connect to GND
75 P102/FIP12 O Hi-z connect to GND
76 P101/FIP11 O Hi-z connect to GND
77 P100/FIP10 O Hi-z connect to GND
78 P97/FIP9 O Hi-z connect to GND
79 P96/FIP8 LED-PR O Hi-z POWER OFF:H
80 P95/FIP7 LED-PG O Hi-z POWER ON:H
11
DRR-M31 12
HA12136AF (IC302)
REC OUT
REC/PB
PB OUT
REC IN
PB IN
BIAS
GND
DET
16 15 14 13 12 11 10 9
BUF SIDE
SW AMP CHAIN
BIAS
SW BUF SIDE
AMP CHAIN
1 2 3 4 5 6 7 8
DET
PB OUT
REC OUT
NR ON/OFF
VREF
PB IN
REC IN
VCC
TRANSISTOR
12
DRR-M31 13
COMPONENT SIDE
13
DRR-M31 14
FOIL SIDE
14
DRR-M31 15
l Resistors l Capacitors
t t t t t t t t
RD : Carbon 2B : 1/8W F : ±1% P : Pulse-resistant type CE : Aluminum foil 0J : 6.3V F : ±1% HS : High stability type
RC : Composition 2E : 1/4W G : ±2% NL : Low noise type electrolytic
RS : Metal oxide film 2H : 1/2W J : ±5% NB : Non-burning type CA : Aluminum solid 1A : 10V G : ±2% BP : Non-polar type
RW : Winding 3A : 1W K : ±10% FR : Fuse-resistor electrolytic
RN : Metal film 3D : 2W M : ±20% F : Lead wire forming CS : Tantalum electrolytic 1C : 16V J : ±5% HR : Ripple-resistant type
CQ : Film 1E : 25V K : ±10% DL : For change and discharge
RK : Metal mixture 3F : 3W
CK : Ceramic 1V : 35V M : ±20% HF : For assuring high
3H : 5W
requency
CC : Ceramic 1H : 50V Z : +80% U : UL part
Resistance
CP : Oil 2A : 100V –20% C : CSA part
1 8 2 ⇒ 1800 ohm = 1.8 kohm CM : Mica 2B : 125V P : +100% W : UL-CSA type
s s
Indicates number of zeros after effective number. CF : Metallized 2C : 160V –0% F : Lead wire forming
2-digit effective number. CH : Metallized 2D : 200V C : ±0.25pF
• Units: ohm 2E : 250V D : ±0.5pF
2H : 500V = : Others
1 R 2 ⇒ 1.2 ohm 2J : 630V
s s
1-digit effective number.
Capacity (electrolyte only)
2-digit effective number, decimal point indicated by R.
• Units: ohm 2 2 2 ⇒ 2200µF
s s
Indicates number of zeros after effective number.
2-digit effective number.
• Units: µF.
2 R 2 ⇒ 2.2µF
s s
1-digit effective number.
2-digit effective number, decimal point indicated by R.
• Units: µF.
2 2 1 ⇒ 220pF
s s
(0 or 1) Indicates number of zeros after effective number.
2-digit effective number.
• Units: pF.
• When the dielectric strength is indicated in AC, "AC" is included after the dieelectric
strength value.
15
DRR-M31 16
16
DRR-M31 17
RESISTORS GROUP
17
DRR-M31 18
18
DRR-M31 19
CAPACITORS GROUP
19
DRR-M31 20
20
DRR-M31 21
21
DRR-M31 22
EXPLODED VIEW
45 WARNING:
Parts marked with this symbol have critical
characteristics.
43 Use ONLY replacement parts recommended by the
manufacturer.
46
40
41
27
42
26
35
34
39
37 29
23 38
14 24
4
9 22
2
1 30
25
28
21
33
15
13 16
11
10 32
12 31
7
8 20
6 36
3 17
18
19
22
DRR-M31 23
SCREWS
23
DRR-M31 24
24
DRR-M31 25
25
DRR-M31 26
26
DRR-M31 27
27
DRR-M31 28
PACKING VIEW
201 ~ 205
207
206
208
209
28
AC CORD
AC OUTLET
4P-PINJACK
CX021
H203
CX022
WIRING DIAGRAM
CW082
CX031
MAIN P.W.B.
CX082 CW081
HEAD
CY062
CX081
AMP P.W.B.
29
H301
POWER TRANS
CY131 CASSETTE MECHA.
CN303
CX151
CN401
DISP P.W.B.
DRR-M31
29
DRR-M31 30
WARNING:
DO NOT return the unit to the customer until the problem
is located and corrected.
NOTICE
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM
M=1,000,000 OHM
ALL CAPACITANCE VALUES IN MICRO FARAD.
P=MICRO-MICRO FARAD
EACH VOLTAGE AND CURRENT ARE MEASURED AT
NO SIGNAL INPUT CONDITION.
CIRCUIT AND PARTS ARE SUBJECT TO CHANGE
WITHOUT PRIOR NOTICE.
30
DRR-M31 31
1 2 3 4 5 6 7 8
DRR-M31
E3
T5A
POWER TRANS (E3)
223 6453 002
AC CORD (E3)
206 2160 009
AC OUTLET (E3/J)
203 3990 004
OPEN : +7.2 V
C
CLOSE : +7.4 V
1 2 3 4 5 6 7 8
PLAY: +6V
STOP, REC PLAY: -7.4V
NORMAL : +9V
HIGH : +14V
STOP : +5V
D