SPECIFICATIONS

IMPORTANT INFORMATION 1
Section 1A - Specifications A
Table of Contents
Master Specifications . . . . . . . . . . . . . . . . . . . . 1A-1 Mercury/Quicksilver Lubricants and Sealants 1A-8
Propeller Information Charts . . . . . . . . . . . . . . 1A-4

Master Specifications

Model 135/150 DFI

HORSEPOWER Model 135 135 (100.7 kw)
(KW) Model 150 150 (111.8 kw)
Full Throttle RPM (135/150) 5000 - 5600
Idle RPM (In Gear) (135/150) 550 ± 25
RPM Limiter
1998 Model 135/150 5750
1999 Model 135 5750
1999 Model 150 5950
OUTBOARD Model 135/150
WEIGHT – 20 in. (50.8cm) Shaft 440.0 lbs. (200.0 kg)
– 25 in. (63.5cm) Shaft 452.0 lbs. (206.0 kg)
CYLINDER Type V-6 Cylinder, Two Cycle, Direct Injected
BLOCK Displacement 153 cu. in. (2508 cc) 60° Vee
STROKE Length (All Models) 2.65 in. (67.3 mm)
CYLINDER Diameter (Standard) 3.501 in. (88.925 mm)
BORE Diameter 0.015 in. Oversize 3.516 in. (89.306 mm)
Taper/Out of Round/Wear Maximum 0.003 in. (0.076 mm)
Bore Type Cast Iron
CRANKSHAFT Maximum Runout 0.006 in. (0.152 mm)
PISTON Piston Type Aluminum
Diameter Standard 3.4925 in. ± .0005 in. (88.7095 mm ±
0.0127 mm)
Diameter 0.015 in. Oversize 3.5075 in. ± 0.0005 in.
(89.0905 mm ± 0.0127 mm)
PISTON 3.4925 in. ± .0005 in.
DIAMETER (88.7095 mm ± .0127 mm)
Using a micrometer, measure dimension
“A” at location shown. Dimension “A”
Dimension should be 3.4925 in. ± .0005 for a STAN-
“A” at Right
DARD size piston (new) Dimension “A”
Angle (90°)
to Piston will be 0.001 – 0.0015 less if coating is
Pin worn off piston (used)
.700
17.78mm

90-855347R02 NOVEMBER 2002 Page 1A-1

SPECIFICATIONS

Model 135/150 DFI

REEDS Reed Stand 0pen (Max.) 0.020 in. (0.50 mm)
MID Power Trim (Total Tilt Range) 73°
SECTION Power Trim (Tilt Range) 19°
Steering Pivot Range 60°
Tilt Pin Adjustment Positions 4
Allowable Transom Thickness 2-3/8 in. (6.03 cm)
GEAR Gear Ratio
HOUSING Standard Ratio – 135 2.00:1 12/24 Teeth
Standard Ratio – 150 1.87:1 15/28 Teeth
Optional High Altitude Ratio
– 135 2.30:1 13/30 Teeth
– 150 2.00:1 12/24 Teeth

Gearcase Capacity 22.5 fl. oz. (665.4 ml)

Pinion Height 0.025 in. (0.635 mm)

.
Forward Gear Backlash
– 1.87:1 0.017 in. – 0.028 in.
(0.431 mm – 0.711 mm)
– 2.00:1 0.015 in. – 0.022 in.
(0.381 mm – 0.558 mm)
– 2.30:1 0.018 in. – 0.023 in.
(0.460 mm – 0.584 mm)
Reverse Gear Backlash
– Standard/Counter Rotation 0.030 in. to 0.050 in.
(0.076 mm to 0.127 mm)
Water Pressure @ RPM 12 PSI Minimum @ 5500 RPM
DIRECT Injectors
INJECTION – Quantity 6
– Injectors are Crank Angle Driven
by ECM
– #2 Cylinder WHT/RED + RED/WHT Leads
– #4 Cylinder WHT/YEL + YEL/WHT Leads
– #6 Cylinder WHT/PPL + PPL/WHT Leads
– #1 Cylinder WHT/BRN + BRN/WHT Leads
– #3 Cylinder WHT/ORG + ORG/WHT Leads
– #5 Cylinder WHT/DRK BLU + DRK BLU/WHT
Leads
Fuel Line Pressure @ Injectors 89 ± 2 psi (613.5 ± 13.8 kPa)
Air Pressure 79 ± 2 psi (544.0 ± 13.8 kPa)
High Pressure Electric Fuel Pump
Amperage Draw 5 – 9 Amperes
Low Pressure Electric Fuel Pump
Amperage Draw 1 – 2 Amperes
Low Pressure Electric Fuel Pump
Output 6 – 9 psi (41.37 – 62.04 kPa)
Fuel Injector Ohm Resistance 1.8 ± 0.1 Ω
Direct Injector Ohm Resistance 1.3 ± 0.3 Ω
Fuel/Air Differential 10 psi (68.5 kPa)

Page 1A-2 90-855347R02 NOVEMBER 2002

 SPECIFICATIONS

Model 135/150 DFI

FUEL Fuel Gasoline with Oil Injection
SYSTEM Recommended Gasoline Unleaded 87 Octane Minimum
Recommended Oil TC-W3 Premium Plus 2 Cycle Outboard
Oil
Gasoline/Oil Ratio
– @ Idle 300 – 400:1
– @ WOT 60:1
Fuel Pressure
Crankcase Pump
– @ Idle 2 psi (13.8 kPa)
– @ WOT 8 psi (55.2 kPa)
STARTING Electric Start – All Models
SYSTEM Starter Draw (Under Load) 165 Amperes
Starter Draw (No Load) 30 Amperes
Minimum Brush Length 0.25 in. (6.35 mm)
Battery Rating 1000 (Minimum) Marine Cranking Amps
(MCA)
750 (Minimum) Cold Cranking Amps
(CCA)
IGNITION Type Digital Inductive
SYSTEM Spark Plug Type NGK PZFR5F-11
NGK ZFR5F-11 or

Spark Plug Gap 0.040 in. (1.0 mm)

Maximum Timing Not Adjustable; Controlled by ECM
Idle Timing Not Adjustable; Controlled by ECM
Throttle Position Sensor 1 (Inner
TPS)
@ Idle 3.70 – 4.90 VDC
@ W.O.T 0.30 – 1.80 VDC
Throttle Position Sensor 2 (Outer
TPS)
@ Idle 0.10 – 1.50 VDC
@ W.O.T 3.20 – 4.90 VDC
Crank Position Sensor
Air Gap 0.025 in. – 0.040 in.
(0.635 mm – 1.01 mm)
CHARGING Alternator Output (Regulated) 32 - 38 Amperes @ 2000 RPM
SYSTEM @ Battery*
52 - 60 Amperes @ 2000 RPM
@ Alternator
Brush Length Std Exposed Length:
0.413 in. (10.5 mm)
Min. Exposed Length:
0.059 in. (1.5 mm)
Voltage Output 13.5 to 15.1 Volts
Regulator Current Draw 0.15 mA (Ign. Switch Off)
30.0 mA (Ign. Switch On)

*Amperage listed is when battery is in a discharged state. If battery is fully charged, amperage readings will
be less.

90-855347R02 NOVEMBER 2002 Page 1A-3

SPECIFICATIONS

Propeller Information Charts

Optimax 115
• Wide Open Throttle RPM: 5000-5500 • Gear Reduction: 2.00:1
No. of Gross Boat Boat Speed Propeller
Diameter Pitch Blades Model Wgt. (lbs) Length (mph) Part Number
13.75″ 26 4 Trophy+ Up to 1600 Up to 18′ 56-63 48-825944A47
13.75″ 25 3 Laser II 1500 – 1700 16 – 18′ 54-60 48-16550A46
13.75″ 25 4 Trophy+ 1500 – 1700 16 – 18′ 54-60 48-825942A47
13.25″ 25 5 Hi-Five 1500 – 1700 16 – 18′ 54-60 48-816374A46
13.38″ 25 3 Vengeance 1500 – 1700 16 – 18′ 54-60 48-16322A45
13.38″ 25 3 Aluminum 1500 – 1700 16 – 18′ 54-60 48-78126A45
13.75″ 24 4 Trophy+ 1600 – 1800 16 – 18′ 51-58 48-825940A47
13.75″ 23 3 Laser II 1700 – 2000 17 – 19′ 49-55 48-16548A46
13.75″ 23 4 Trophy+ 1700 – 2000 17 – 19′ 49-55 48-825938A47
13.25″ 23 5 Hi-Five 1700 – 2000 17 – 19′ 49-55 48-815762A46
13.5″ 23 3 Vengeance 1700 – 2000 17 – 19′ 49-55 48-16320A45
14″ 23 3 Aluminum 1700 – 2000 17 – 19′ 49-55 48-832834A45
13.88″ 21 3 Laser II 1900 – 2300 18 – 20′ 43-50 48-16546A46
13.75″ 21 4 Trophy+ 1900 – 2300 18 – 20′ 43-50 48-825936A47
13.25″ 21 5 Hi-Five 1900 – 2300 18 – 20′ 43-50 48-815760A46
13.75″ 21 3 Vengeance 1900 – 2300 18 – 20′ 43-50 48-16318A45
14.25″ 21 3 Aluminum 1900 – 2300 18 – 20′ 43-50 48-832832A45
14″ 19 3 Laser II 2100 – 2500 18 – 21′ 38-45 48-16544A46
13.75″ 19 4 Trophy+ 2100 – 2500 18 – 21′ 38-45 48-825932A46
13.25″ 19 5 Hi-Five 2100 – 2500 18 – 21′ 38-45 48-815758A46
14″ 19 3 Vengeance 2100 – 2500 18 – 21′ 38-45 48-16316A45
14.5″ 19 3 Aluminum 2100 – 2500 18 – 21′ 38-45 48-832830A45
13.75″ 17 4 Trophy+ 2300 – 3100 19 – 22′ 32-40 48-825930A46
13.5″ 17 5 Hi-Five 2300 – 3100 19 – 22′ 32-40 48-821154A46
14.5″ 17 3 Vengeance 2300 – 3100 19 – 22′ 32-40 48-16314A45
15″ 17 3 Aluminum 2300 – 3100 19 – 22′ 32-40 48-832828A45
14.5″ 15 3 Vengeance 2900 – 4100 20 – 24′ 25-34 48-16312A45
15.5″ 15 3 Aluminum 2900 – 4100 20 – 24′ 25-34 48-78116A45
16″ 13 3 Aluminum 4000+ Pontoon 19-28 48-78114A45
16″ 12 3 Aluminum 4500+ Pontoon/Work 16-25 48-16436A45
16″ 11 3 Aluminum 5500+ House/Work 1-20 48-78112A45

Page 1A-4 90-855347R02 NOVEMBER 2002

 SPECIFICATIONS

Optimax 135
• Wide Open Throttle RPM: 5000-5500 • Gear Reduction: 2.00:1
No. of Gross Boat Boat Speed Propeller
Diameter Pitch Blades Model Wgt. (lbs) Length (mph) Part Number
13.75″ 26 4 Trophy+ Up to 1900 Up to 18′ 56-63 48-825944A47
13.75″ 25 3 Laser II 1800 – 2000 16 – 18′ 54-60 48-16550A46
13.75″ 25 4 Trophy+ 1800 – 2000 16 – 18′ 54-60 48-825942A47
13.25″ 25 5 Hi-Five 1800 – 2000 16 – 18′ 54-60 48-816374A46
13.38″ 25 3 Vengeance 1800 – 2000 16 – 18′ 54-60 48-16322A45
13.38″ 25 3 Aluminum 1800 – 2000 16 – 18′ 54-60 48-78126A45
13.75″ 24 4 Trophy+ 1900 – 2100 16 – 18′ 51-58 48-825940A47
13.75″ 23 3 Laser II 2000 – 2300 17 – 19′ 49-55 48-16548A46
13.75″ 23 4 Trophy+ 2000 – 2300 17 – 19′ 49-55 48-825938A47
13.25″ 23 5 Hi-Five 2000 – 2300 17 – 19′ 49-55 48-815762A46
13.5″ 23 3 Vengeance 2000 – 2300 17 – 19′ 49-55 48-16320A45
14″ 23 3 Aluminum 2000 – 2300 17 – 19′ 49-55 48-832834A45
13.88″ 21 3 Laser II 2200 – 2600 18 – 20′ 43-50 48-16546A46
13.75″ 21 4 Trophy+ 2200 – 2600 18 – 20′ 43-50 48-825936A47
13.25″ 21 5 Hi-Five 2200 – 2600 18 – 20′ 43-50 48-815760A46
13.75″ 21 3 Vengeance 2200 – 2600 18 – 20′ 43-50 48-16318A45
14.25″ 21 3 Aluminum 2200 – 2600 18 – 20′ 43-50 48-832832A45
14″ 19 3 Laser II 2500 – 3000 18 – 21′ 38-45 48-16544A46
13.75″ 19 4 Trophy+ 2500 – 3000 18 – 21′ 38-45 48-825932A46
13.25″ 19 5 Hi-Five 2500 – 3000 18 – 21′ 38-45 48-815758A46
14″ 19 3 Vengeance 2500 – 3000 18 – 21′ 38-45 48-16316A45
14.5″ 19 3 Aluminum 2500 – 3000 18 – 21′ 38-45 48-832830A45
13.75″ 17 4 Trophy+ 2800 – 3600 19 – 22′ 32-40 48-825930A46
13.5″ 17 5 Hi-Five 2800 – 3600 19 – 22′ 32-40 48-821154A46
14.5″ 17 3 Vengeance 2800 – 3600 19 – 22′ 32-40 48-16314A45
15″ 17 3 Aluminum 2800 – 3600 19 – 22′ 32-40 48-832828A45
14.5″ 15 3 Vengeance 3400 – 4800 20 – 24′ 25-34 48-16312A45
15.5″ 15 3 Aluminum 3400 – 4800 20 – 24′ 25-34 48-78116A45
16″ 13 3 Aluminum 4500+ Pontoon 19-28 48-78114A45
16″ 12 3 Aluminum 5500+ Pontoon/Work 16-25 48-16436A45
16″ 11 3 Aluminum 6500+ House/Work 1-20 48-78112A45

90-855347R02 NOVEMBER 2002 Page 1A-5

SPECIFICATIONS

Optimax 150
• Wide Open Throttle RPM: 5250-5750 • Gear Reduction: 1.87:1
No. of Gross Boat Boat Speed Propeller
Diameter Pitch Blades Model Wgt. (lbs) Length (mph) Part Number
14.62″ 27 3 Tempest+ Up to 1800 Up to 18′ 66-74 48-825868A47
13.75″ 26 4 Trophy+ Up to 1900 Up to 19′ 64-71 48-825944A47
14.62″ 26 3 Tempest+ Up to 1900 Up to 19′ 64-71 48-825874A47
13.75″ 25 3 Laser II 1700 – 2000 17 – 19′ 61-68 48-16550A46
13.75″ 25 4 Trophy+ 1700 – 2000 17 – 19′ 61-68 48-825942A47
14.62″ 25 3 Tempest+ 1700 – 2000 17 – 19′ 61-68 48-825866A47
13.25″ 25 5 Hi-Five 1700 – 2000 17 – 19′ 61-68 48-816374A46
13.38″ 25 3 Aluminum 1700 – 2000 17 – 19′ 61-68 48-78126A45
13.75″ 24 4 Trophy+ 1800 – 2100 18 – 20′ 58-65 48-825940A47
14.62″ 24 3 Tempest+ 1800 – 2100 18 – 20′ 58-65 48-825872A47
13.75″ 23 3 Laser II 1900 – 2200 18 – 20′ 55-62 48-16548A46
13.75″ 23 4 Trophy+ 1900 – 2200 18 – 20′ 55-62 48-825938A47
14.62″ 23 3 Tempest+ 1900 – 2200 18 – 20′ 55-62 48-825864A47
13.25″ 23 5 Hi-Five 1900 – 2200 18 – 20′ 55-62 48-815762A46
13.5″ 23 3 Vengeance 1900 – 2200 18 – 20′ 55-62 48-16320A46
14″ 23 3 Aluminum 1900 – 2200 18 – 20′ 55-62 48-832834A45
13.88″ 21 3 Laser II 2000 – 2500 18 – 21′ 50-57 48-16546A46
13.75″ 21 4 Trophy+ 2000 – 2500 18 – 21′ 50-57 48-825934A47
14.62″ 21 3 Tempest+ 2000 – 2500 18 – 21′ 50-57 48-825862A47
13.25″ 21 5 Hi-Five 2000 – 2500 18 – 21′ 50-57 48-815760A46
13.75″ 21 3 Vengeance 2000 – 2500 18 – 21′ 50-57 48-16318A46
14.25″ 21 3 Aluminum 2000 – 2500 18 – 21′ 50-57 48-832832A45
14″ 19 3 Laser II 2300 – 2900 19 – 22′ 44-52 48-16544A46
13.75″ 19 4 Trophy+ 2300 – 2900 19 – 22′ 44-52 48-825932A46
14.62″ 19 3 Tempest+ 2300 – 2900 19 – 22′ 44-52 48-825860A47
13.25″ 19 5 Hi-Five 2300 – 2900 19 – 22′ 44-52 48-815758A46
14″ 19 3 Vengeance 2300 – 2900 19 – 22′ 44-52 48-16316A46
14.5″ 19 3 Aluminum 2300 – 2900 19 – 22′ 44-52 48-832830A45
13.5″ 17 5 Hi-Five 2700 – 3500 19 – 23′ 38-46 48-821154A46
14.5″ 17 3 Vengeance 2700 – 3500 19 – 23′ 38-46 48-16314A46
15″ 17 3 Aluminum 2700 – 3500 19 – 23′ 38-46 48-832828A45
14.5″ 15 3 Vengeance 3200 – 4500 21 – 25′ 31-40 48-16312A46
15.25″ 15 3 Aluminum 3200 – 4500 21 – 25′ 31-40 48-78116A45
16″ 13 3 Aluminum 4000+ Pontoon 23-33 48-78114A45
16″ 12 3 Aluminum 5500+ Pontoon/Work 16-27 48-16436A45
16″ 11 3 Aluminum 7500+ House/Work 1-23 48-78112A45

Page 1A-6 90-855347R02 NOVEMBER 2002

 SPECIFICATIONS

Optimax 175
• Wide Open Throttle RPM: 5250-5750 • Gear Reduction: 1.87:1
No. of Gross Boat Boat Speed Propeller
Diameter Pitch Blades Model Wgt. (lbs) Length (mph) Part Number
14.62″ 27 3 Tempest+ Up to 2100 Up to 18′ 66-74 48-825868A47
13.75″ 26 4 Trophy+ Up to 2300 Up to 19′ 64-71 48-825944A47
14.62″ 26 3 Tempest+ Up to 2300 Up to 19′ 64-71 48-825874A47
13.75″ 25 3 Laser II 2000 – 2400 17 – 19′ 61-68 48-16550A46
13.75″ 25 4 Trophy+ 2000 – 2400 17 – 19′ 61-68 48-825942A47
14.62″ 25 3 Tempest+ 2000 – 2400 17 – 19′ 61-68 48-825866A47
13.25″ 25 5 Hi-Five 2000 – 2400 17 – 19′ 61-68 48-816374A46
13.38″ 25 3 Aluminum 2000 – 2400 17 – 19′ 61-68 48-78126A45
13.75″ 24 4 Trophy+ 2100 – 2500 18 – 20′ 58-65 48-825940A47
14.62″ 24 3 Tempest+ 2100 – 2500 18 – 20′ 58-65 48-825872A47
13.75″ 23 3 Laser II 2200 – 2600 18 – 20′ 55-62 48-16548A46
13.75″ 23 4 Trophy+ 2200 – 2600 18 – 20′ 55-62 48-825938A47
14.62″ 23 3 Tempest+ 2200 – 2600 18 – 20′ 55-62 48-825864A47
13.25″ 23 5 Hi-Five 2200 – 2600 18 – 20′ 55-62 48-815762A46
13.5″ 23 3 Vengeance 2200 – 2600 18 – 20′ 55-62 48-16320A46
14″ 23 3 Aluminum 2200 – 2600 18 – 20′ 55-62 48-832834A45
13.88″ 21 3 Laser II 2400 – 2900 18 – 21′ 50-57 48-16546A46
13.75″ 21 4 Trophy+ 2400 – 2900 18 – 21′ 50-57 48-825934A47
14.62″ 21 3 Tempest+ 2400 – 2900 18 – 21′ 50-57 48-825862A47
13.25″ 21 5 Hi-Five 2400 – 2900 18 – 21′ 50-57 48-815760A46
13.75″ 21 3 Vengeance 2400 – 2900 18 – 21′ 50-57 48-16318A46
14.25″ 21 3 Aluminum 2400 – 2900 18 – 21′ 50-57 48-832832A45
14″ 19 3 Laser II 2700 – 3300 19 – 22′ 44-52 48-16544A46
13.75″ 19 4 Trophy+ 2700 – 3300 19 – 22′ 44-52 48-825932A46
14.62″ 19 3 Tempest+ 2700 – 3300 19 – 22′ 44-52 48-825860A47
13.25″ 19 5 Hi-Five 2700 – 3300 19 – 22′ 44-52 48-815758A46
14″ 19 3 Vengeance 2700 – 3300 19 – 22′ 44-52 48-16316A46
14.5″ 19 3 Aluminum 2700 – 3300 19 – 22′ 44-52 48-832830A45
13.5″ 17 5 Hi-Five 3100 – 3900 19 – 23′ 38-46 48-821154A46
14.5″ 17 3 Vengeance 3100 – 3900 19 – 23′ 38-46 48-16314A46
15″ 17 3 Aluminum 3100 – 3900 19 – 23′ 38-46 48-832828A45
14.5″ 15 3 Vengeance 3700 – 4900 21 – 25′ 31-40 48-16312A46
15.25″ 15 3 Aluminum 3700 – 4900 21 – 25′ 31-40 48-78116A45
16″ 13 3 Aluminum 4500+ Pontoon 23-33 48-78114A45
16″ 12 3 Aluminum 6000+ Pontoon/Work 16-27 48-16436A45
16″ 11 3 Aluminum 8000+ House/Work 1-23 48-78112A45

90-855347R02 NOVEMBER 2002 Page 1A-7

SPECIFICATIONS

Mercury/Quicksilver Lubricants and Sealants

Tube Mercury Part Quicksilver Part
Description Container Size
Ref. # Number Number
Needle Bearing Assy.
4 8 oz (226.8 g) tube 92-802868A1 N/A
Lubricant
Dielectric Grease
6 8 oz (226.8 g) can 92-823506-1 92-823506-1

Loctite 271 – Thread

7 10 ml tube 92-809819 92-809819
Locker
Loctite 567 PST Pipe
9 50 ml tube 92-809822 92-809822
Sealant
Loctite Master Gas-
12 92-12564-2 92-12564-2
ket Kit
2 Cycle Premium
14 1 US qt (0.94 L) 92-802813A1 92-802813Q1
Outboard Oil
19 Perfect Seal 16 oz (0.45 kg) can 92-34227-1 92-34227-1

25 Liquid Neoprene 8 oz (226.8 g) can 92-25711-3 92-25711-3

27 Bellows Adhesive 1.5 oz (42.5 g) tube N/A 92-86166Q1

Loctite 680 Retaining
33 10 ml tube 92-809833 92-809833
Compound
34 Special Lubricant 101 8 oz (226.8 g) tube 92-802865A1 92-802865Q1
U-Joint and Gimbal 92-802870A1 92-802870Q1
42
Bearing Grease
Loctite 222 Thread
51 10 ml tube 92-809818 92-809818
Locker
Loctite 242 Thread
66 10 ml tube 92-809821 92-809821
Locker
4 Cycle 25W40 En-
79 92-802837A1 92-802837Q1
gine Oil
Premium Gear Lubri-
82 1 US qt (0.94 L) 92-802846A1 92-802846Q1
cant
High Performance 1 US qt (0.94 L) 92-802854A1 92-802854Q1
87
Gear Lube
Engine Coupler 14 oz (0.39 kg) car-
91 92-802869A1 92-802869Q1
Spline Grease tridge
Anti-Corrosion
94 8 oz (226.8 g) tube 92-802867A1 92-802867Q1
Grease
95 2-4-C with Teflon 8 oz (226.8 g) tube 92-802859A1 92-802859Q1
4 Stroke 10W30 Out-
110 1 US qt (0.94 L) 92-802833A1 92-802833Q1
board Oil
Power Trim & Steer-
114 8 oz (226.8 g) 92-802880A1 92-802880Q1
ing Fluid

Page 1A-8 90-855347R02 NOVEMBER 2002

 SPECIFICATIONS

Tube Mercury Part Quicksilver Part

Description Container Size
Ref. # Number Number
Premium Plus 2
115 Cycle TC-W3 Out- 1 US qt (0.94 L) 92-802824A1 92-802824Q1
board Oil
RTV 587 Silicone
116 3 oz (85.05 g) 92-809825 92-809825
Sealer
117 Loctite 7649 Primer N 4.5 oz (127.57 g) 92-809824 92-809824
Storage Seal Rust In- 12 oz (325 ml) spray 92-802878-56 92-802878Q56
119
hibitor can
Corrosion Guard 12 oz (325 ml) spray 92-802878 55 92-802878Q55
120
can
121
15W40 4-cycle Diesel 1.06 US gal.(4 L) 92-877695K1 92-877695Q1
Engine Oil
Extended Life Anti- 1 US gal. (3.78 L) 92-877770K1 92-877770K1
122
freeze/Coolant
Marine Engine Cool- 1.33 US gal. (5 L) NA 92-813054A2
123
ant
Fuel System Treat-
124 ment and Stabilizer 16 oz (437 ml) 92-802876A1 92-802876Q1
Concentrate
Heat Transfer Com- 1.5 oz (42.5 g) tube 92-805701 1
125
pound
126 Liquid Gasket 92-808137 NA

127 T442 Sealant 92-862258 NA

Loctite 5900 Ultra 13 oz (371 g) tube 92-809826 NA
128 Black RTV Silicone
Sealant
Loctite Gasket Re- 18 oz (532 ml) spray 92-809828 1 NA
129
mover can
Sealer Kit, Two Part NA 92-65150 1
130
Epoxy
Dexron III Automatic Obtain Locally Obtain Locally
Transmission Fluid
Loctite 592 Obtain Locally Obtain Locally
Loctite Quick Tite Obtain Locally Obtain Locally
Isopropyl Alcohol Obtain Locally Obtain Locally
Hot Glue Obtain Locally Obtain Locally
Loctite 609 Obtain Locally Obtain Locally
Loctite 405 Obtain Locally Obtain Locally

90-855347R02 NOVEMBER 2002 Page 1A-9

SPECIFICATIONS

Tube Mercury Part Quicksilver Part

Description Container Size
Ref. # Number Number
Cyanacrylate Adhe-
Obtain Locally Obtain Locally
sive
3M Permabond
Obtain Locally Obtain Locally
#3M08155
Loctite 262 Obtain Locally Obtain Locally
Loctite 290 Obtain Locally Obtain Locally

Page 1A-10 90-855347R02 NOVEMBER 2002