Page 1 of 4
Electronic Service Tool 2016C v1.0
Cylinder Cutout Results - LHX08120_CYLCUT_2024-07-
06_12.21.08.CCR
7/7/2024 10:11 AM
Comments:
C15 980H LHX08120 AUSTRALIA
Test Summary
Parameter Value
Dealer Name: 980H
Dealer Code:
Engine Serial Number: LHX08120
Engine Model: C15 980H (LHX08120)
Total Time: 20182 hours
Total Fuel: 162353 gal
General
Parameter Value
Site Name:
Site Location:
Operator:
Dealer Name: 980H
Dealer Code:
Date/Time Test Completed: 7/6/2024 12:20:16 PM
Service Tool Serial Number: ET012345
Service Tool Version: 2019C v1.0
Cylinder Status
Cylinder Status
Cylinder 1 OK
Cylinder 2 OK
Cylinder 3 OK
Cylinder 4 OK
Cylinder 5 OK
Cylinder 6 OK
file:///C:/ProgramData/Perkins/Electronic%20Service%20Tool/temp/STPLReport1.HTM 7/7/2024
Page 2 of 4
Injector Serial Number
Injector ECM Injector Serial Number Stamped Serial Number on Injector
Injector 1 5A50974779EE **********
Injector 2 5A5097478707 **********
Injector 3 5A50974756E9 **********
Injector 4 5A50974742E0 **********
Injector 5 5A50974749D1 **********
Injector 6 5A50974775CA **********
Warranty claim will be invalid if the injector serial number entered does not match the
serial number stamped on the physical injector.
Fuel Delivery
Cylinder Fuel Delivery
Cylinder 1 2.3
Cylinder 2 2.3
Cylinder 3 2.3
Cylinder 4 2.4
Cylinder 5 2.3
Cylinder 6 2.3
All Firing Fuel Delivery: 0.0
Symptoms
Symptom Value
Low Power No
High Power No
Rough Idle (Engine Lope) No
Rough Running Under Load No
Hard Starting No
Stumble/Miss on Acceleration No
Excessive Smoke No
Engine Information
Parameter Value
Engine Model: C15 980H (LHX08120)
Engine Serial Number: LHX08120
Equipment ID: NOT PROGRAMMED
file:///C:/ProgramData/Perkins/Electronic%20Service%20Tool/temp/STPLReport1.HTM 7/7/2024
Page 3 of 4
Rated Peak Torque: Unavailable
Rated Power: Unavailable
Total Time: 20182 hours
Total Fuel: 162353 gal
Total Distance: Unavailable
Personality Module Part Number: 3154121-00
Personality Module Release Date: JUL07
Personality Module Description: C15-980H
ECM Serial Number: 16766452JL
Active Diagnostics and Events
Active Codes
267- 2 Remote Shutdown Input : Erratic, Intermittent, or Incorrect
Active Events
No Active Events
Test Conditions
The following conditions must be met for the automatic Cylinder Cutout Test:
1) Engine Speed must be between 980 rpm and 1020 rpm (engine speed will be
automatically adjusted)
2) Engine Coolant Temperature must be 170 Deg F or higher
3) No engine performance related active diagnostic codes are allowed
4) No default injector serial numbers (000000000000) allowed.
5) Throttle position must not vary by +/- 5 %
If at any time any of these conditions are not met, the test will automatically be aborted.
Note: Ensure transmission is in neutral or electrical load is removed from generator set.
Note: Fan cycling, A/C compressor cycling, or changes in engine load will invalidate this
test. 1) If the fan is not controlled by the engine ECM, please enable the fan if possible.
2) WARNING: If the ECM controls the fan, the fan will be turned ON automatically upon
starting this test.
WARNING: Please make sure the compression brake is in the off position. During the test,
compression brake operation will cause the engine to surge.
file:///C:/ProgramData/Perkins/Electronic%20Service%20Tool/temp/STPLReport1.HTM 7/7/2024
Page 4 of 4
Comments
Run this test before and after repairing a cylinder to confirm a successful repair. Include
printed or electronic copies of the test results with any injectors that are returned to the
factory. Mark injectors with the cylinder number from which they were removed.
file:///C:/ProgramData/Perkins/Electronic%20Service%20Tool/temp/STPLReport1.HTM 7/7/2024
