Hardware Maintenance Manual

Lenovo 3000 J Series

Types 7387, 7388, 7389, 7390, 7391, 7392,

7393, 7394, 7395, 7396, 7397, 7398

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Note: Before using this information and the product it supports, be sure to read the
information under “Notices,” on page 211.

Seventh Edition (August 2007)

© Copyright Lenovo 2006.
Portions © Copyright International Business Machines Corporation 2005, 2006.
All rights reserved.
LENOVO products, data, computer software, and services have been developed exclusively at private expense and
are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted
rights to use, reproduction and disclosure.
LIMITED AND RESTRICTED RIGHTS NOTICE: If products, data, computer software, or services are delivered
pursuant a General Services Administration ″GSA″ contract, use, reproduction, or disclosure is subject to restrictions
set forth in Contract No. GS-35F-05925.

Downloaded from www.Manualslib.com manuals search engine

 Contents
Chapter 1. About this manual . . . . . 1 Chapter 7. Symptom-to-FRU Index . . . 55
Important Safety Information . . . . . . . . . 1 Hard disk drive boot error . . . . . . . . . 55
Important information about replacing RoHS Power Supply Problems . . . . . . . . . . 55
compliant FRUs . . . . . . . . . . . . . 2 Diagnostic error codes . . . . . . . . . . . 56
Beep symptoms . . . . . . . . . . . . . 77
Chapter 2. Safety information . . . . . 3 POST error codes . . . . . . . . . . . . 78
General safety . . . . . . . . . . . . . . 3 Miscellaneous error messages . . . . . . . . 80
Electrical safety . . . . . . . . . . . . . 3 Undetermined problems . . . . . . . . . . 81
Safety inspection guide . . . . . . . . . . . 5
Handling electrostatic discharge-sensitive devices . . 6 Chapter 8. Replacing FRUs (Types
Grounding requirements . . . . . . . . . . 6 7387, 7388, 7389, 7393, 7394, and 7395) 83
Safety notices (multi-lingual translations) . . . . . 7 Rear connectors . . . . . . . . . . . . . 84
Removing the covers . . . . . . . . . . . 84
Chapter 3. General information . . . . 37 Locations . . . . . . . . . . . . . . . 86
The Lenovo Care program . . . . . . . . . 37 Identifying parts on the system board . . . . . 87
Additional information resources . . . . . . . 37 Machine Types 7387, 7388, and 7389 . . . . . 87
Specifications . . . . . . . . . . . . . . 38 Machine Types 7393, 7394, and 7395 . . . . . 88
Machine types 7387, 7388, 7389, 7393, 7394, and Removing and replacing the front bezel . . . . . 89
7395 . . . . . . . . . . . . . . . . 38 Replacing a memory module . . . . . . . . 90
Machine types 7390, 7391, 7392, 7396, 7397, and Replacing a PCI adapter . . . . . . . . . . 91
7398 . . . . . . . . . . . . . . . . 39 Replacing the CMOS battery. . . . . . . . . 92
Replacing the power supply . . . . . . . . . 93
Chapter 4. General Checkout . . . . . 41 Replacing the system board (Types 7393, 7394, and
Problem determination tips . . . . . . . . . 41 7395) . . . . . . . . . . . . . . . . 94
Replacing the system board (Types 7387, 7388, and
7389) . . . . . . . . . . . . . . . . 97
Chapter 5. Diagnostics . . . . . . . . 43 Replacing the microprocessor (Types 7393, 7394,
PC-Doctor for Windows . . . . . . . . . . 43 and 7395) . . . . . . . . . . . . . . . 100
PC-Doctor for DOS . . . . . . . . . . . . 43 Replacing the microprocessor (Types 7387, 7388,
Creating a diagnostic CD image . . . . . . 44 and 7389) . . . . . . . . . . . . . . . 104
Creating diagnostic diskettes . . . . . . . 44 Replacing the primary hard disk drive . . . . . 107
Running diagnostics from the CD or diskettes . . 44 Replacing an optical drive . . . . . . . . . 108
Running diagnostics from the Rescue and Replacing the diskette drive . . . . . . . . 109
Recovery workspace . . . . . . . . . . 45 Replacing the power switch/ LED assembly . . . 110
PC-Doctor for Windows PE . . . . . . . . . 45 Replacing the front panel card assembly . . . . 111
Running diagnostics from the Rescue and Completing the FRU replacement . . . . . . . 112
Recovery workspace . . . . . . . . . . 45
Navigating through the diagnostics programs . . . 46
Running tests . . . . . . . . . . . . . . 46
Chapter 9. Replacing FRUs (Types
Test results . . . . . . . . . . . . . 46 7390, 7391, 7392, 7396, 7397, and
Fixed disk advanced test (FDAT) . . . . . . 47 7398) . . . . . . . . . . . . . . . 113
Quick and Full erase - hard drive . . . . . . 48 Rear connectors . . . . . . . . . . . . 114
Viewing the test log . . . . . . . . . . . 49 Removing the cover . . . . . . . . . . . 114
Locations . . . . . . . . . . . . . . . 115
Chapter 6. Using the Setup Utility . . . 51 Identifying parts on the system board . . . . . 116
Starting the Setup Utility program . . . . . . . 51 Machine Types 7390, 7391, and 7392 . . . . . 116
Viewing and changing settings . . . . . . . . 51 Machine Types 7396, 7397, and 7398 . . . . . 117
Using passwords . . . . . . . . . . . . 51 Removing and replacing the drive bay assembly 118
User Password . . . . . . . . . . . . 51 Replacing a memory module . . . . . . . . 120
Administrator or Supervisor Password . . . . 52 Replacing a PCI adapter . . . . . . . . . . 121
Selecting a startup device . . . . . . . . . . 53 Replacing the CMOS battery . . . . . . . . 122
Selecting a temporary startup device . . . . . 53 Replacing the power supply . . . . . . . . 123
Changing the startup device sequence . . . . 53 Replacing the system board (Types 7396, 7397, and
Exiting from the Setup Utility program . . . . . 53 7398) . . . . . . . . . . . . . . . . 125

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. iii

Downloaded from www.Manualslib.com manuals search engine

 Replacing the system board (Types 7390, 7391, and Machine Type 7397 . . . . . . . . . . . 198
7392) . . . . . . . . . . . . . . . . 129 Machine Type 7398 . . . . . . . . . . . 203
Replacing the microprocessor (Types 7396, 7397,
and 7398) . . . . . . . . . . . . . . . 132 Chapter 11. Additional Service
Replacing the microprocessor (Types 7390, 7391, Information . . . . . . . . . . . . 207
and 7392) . . . . . . . . . . . . . . . 136
Security features . . . . . . . . . . . . 207
Replacing the hard disk drive . . . . . . . . 140
Hardware controlled Passwords . . . . . . 207
Replacing an optical drive . . . . . . . . . 141
Operating system password . . . . . . . 207
Replacing the diskette drive . . . . . . . . 142
Vital product data . . . . . . . . . . . 207
Replacing the power switch/ LED assembly . . . 143
BIOS levels . . . . . . . . . . . . . . 207
Replacing the front panel card . . . . . . . . 144
Flash update procedures. . . . . . . . . . 207
Completing the FRU replacement . . . . . . 144
Updating (flashing) BIOS from a diskette . . . 208
Recovering from a POST/BIOS update failure . . 208
Chapter 10. FRU lists . . . . . . . . 147 Power management . . . . . . . . . . . 209
Machine Type 7387 . . . . . . . . . . . 148 Automatic configuration and power interface
Machine Type 7388 . . . . . . . . . . . 156 (ACPI) BIOS . . . . . . . . . . . . . 209
Machine Type 7389 . . . . . . . . . . . 161 Automatic Power-On features . . . . . . . 209
Machine Type 7390 . . . . . . . . . . . 165 Recovering software . . . . . . . . . . . 210
Machine Type 7392 . . . . . . . . . . . 169
Machine Type 7393 . . . . . . . . . . . 173 Appendix. Notices . . . . . . . . . 211
Machine Type 7394 . . . . . . . . . . . 181
Television output notice . . . . . . . . . . 212
Machine Type 7395 . . . . . . . . . . . 186
Trademarks . . . . . . . . . . . . . . 212
Machine Type 7396 . . . . . . . . . . . 190

iv Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 1. About this manual
This manual contains service and reference information for Lenovo™ computers
listed on the cover. It is intended only for trained servicers who are familiar with
Lenovo computer products.

Before servicing a Lenovo product, be sure to read the Safety Information. See
Chapter 2, “Safety information,” on page 3.

The Symptom-to-FRU Index and Additional Service Information chapters are not
specific to any machine type and are applicable to all Lenovo computers.

This manual includes a complete FRU part number listing for each machine type
and model listed on the cover. If you have internet access, FRU part numbers are
also available at:
http:/www.lenovo.com/support

Important Safety Information

Be sure to read all caution and danger statements in this book before performing
any of the instructions.

Veuillez lire toutes les consignes de type DANGER et ATTENTION du présent

document avant d’exécuter les instructions.

Lesen Sie unbedingt alle Hinweise vom Typ ″ACHTUNG″ oder ″VORSICHT″ in
dieser Dokumentation, bevor Sie irgendwelche Vorgänge durchführen

Leggere le istruzioni introdotte da ATTENZIONE e PERICOLO presenti nel

manuale prima di eseguire una qualsiasi delle istruzioni

Certifique-se de ler todas as instruções de cuidado e perigo neste manual antes de

executar qualquer uma das instruções

Es importante que lea todas las declaraciones de precaución y de peligro de este

manual antes de seguir las instrucciones.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 1

Downloaded from www.Manualslib.com manuals search engine

 Important information about replacing RoHS compliant FRUs
RoHS, The Restriction of Hazardous Substances in Electrical and Electronic
Equipment Directive (2002/95/EC) is a European Union legal requirement
affecting the global electronics industry. RoHS requirements must be
implemented on Lenovo products placed on the market after June 2006. Products
on the market before June 2006 are not required to have RoHS compliant parts.
So, if the parts are not compliant originally, replacement parts can also be
noncompliant, but in all cases, if the parts are compliant, the replacement parts
must also be compliant.

Lenovo plans to transition to RoHS compliance well before the implementation

date and expects its suppliers to be ready to support Lenovo’s requirements and
schedule. Products sold in 2005, will contain some RoHS compliant FRUs. The
following statement pertains to these products and any product Lenovo produces
containing RoHS compliant parts.

RoHS compliant Lenovo parts have unique FRU part numbers. Before or after
June, 2006, failed RoHS compliant parts must always be replaced using RoHS
compliant FRUs, so only the FRUs identified as compliant in the system HMM or
direct substitutions for those FRUs can be used.

Products marketed before June 2006 Products marketed after June 2006
Current or original Replacement FRU Current or original Replacement FRU
part part
Non-RoHS Can be Non-RoHS Must be RoHS Must be RoHS
Non-RoHS Can be RoHS
Non-RoHS Can sub to RoHS
RoHS Must be RoHS

Note: A direct substitution is a part with a different FRU part number that is
automatically shipped by the distribution center at the time of order.

Related Web URLs are:

v Lenovo information for Suppliers website:
http://www-03.ibm.com/procurement/proweb.nsf/ContentDocsByTitle/
United+States~Information+for+suppliers
v RoHS Directive:
http://europa.eu.int/eur-lex/pri/en/oj/dat/2003/l_037/
l_03720030213en00190023.pdf
v California Senate Bills 20, 50:
http://www.ciwmb.ca.gov/HHW/Events/AnnualConf/2004/
presentation/MPaparian.pdf

2 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2. Safety information
This chapter contains the safety information that you need to be familiar with
before servicing a computer.

General safety
Follow these rules to ensure general safety:
v Observe good housekeeping in the area of the machines during and after
maintenance.
v When lifting any heavy object:
1. Ensure you can stand safely without slipping.
2. Distribute the weight of the object equally between your feet.
3. Use a slow lifting force. Never move suddenly or twist when you attempt to
lift.
4. Lift by standing or by pushing up with your leg muscles; this action removes
the strain from the muscles in your back. Do not attempt to lift any objects that
weigh more than 16 kg (35 lb) or objects that you think are too heavy for you.
v Do not perform any action that causes hazards to the customer, or that makes
the equipment unsafe.
v Before you start the machine, ensure that other service representatives and the
customer’s personnel are not in a hazardous position.
v Place removed covers and other parts in a safe place, away from all personnel,
while you are servicing the machine.
v Keep your tool case away from walk areas so that other people will not trip over
it.
v Do not wear loose clothing that can be trapped in the moving parts of a
machine. Ensure that your sleeves are fastened or rolled up above your elbows.
If your hair is long, fasten it.
v Insert the ends of your necktie or scarf inside clothing or fasten it with a
nonconductive clip, approximately 8 centimeters (3 inches) from the end.
v Do not wear jewelry, chains, metal-frame eyeglasses, or metal fasteners for your
clothing.
Remember: Metal objects are good electrical conductors.
v Wear safety glasses when you are: hammering, drilling soldering, cutting wire,
attaching springs, using solvents, or working in any other conditions that might
be hazardous to your eyes.
v After service, reinstall all safety shields, guards, labels, and ground wires.
Replace any safety device that is worn or defective.
v Reinstall all covers correctly before returning the machine to the customer.

Electrical safety

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 3

Downloaded from www.Manualslib.com manuals search engine

 CAUTION:
Electrical current from power, telephone, and communication cables can be
hazardous. To avoid personal injury or equipment damage, disconnect the
attached power cords, telecommunication systems, networks, and modems before
you open the server/workstation covers, unless instructed otherwise in the
installation and configuration procedures.

Observe the following rules when working on electrical equipment.

Important: Use only approved tools and test equipment. Some hand tools have
handles covered with a soft material that does not insulate you when
working with live electrical currents.

Many customers have, near their equipment, rubber floor mats that
contain small conductive fibers to decrease electrostatic discharges. Do
not use this type of mat to protect yourself from electrical shock.
v Find the room emergency power-off (EPO) switch, disconnecting switch, or
electrical outlet. If an electrical accident occurs, you can then operate the switch
or unplug the power cord quickly.
v Do not work alone under hazardous conditions or near equipment that has
hazardous voltages.
v Disconnect all power before:
– Performing a mechanical inspection
– Working near power supplies
– Removing or installing main units
v Before you start to work on the machine, unplug the power cord. If you cannot
unplug it, ask the customer to power-off the wall box that supplies power to the
machine and to lock the wall box in the off position.
v If you need to work on a machine that has exposed electrical circuits, observe
the following precautions:
– Ensure that another person, familiar with the power-off controls, is near you.
Remember: Another person must be there to switch off the power, if
necessary.
– Use only one hand when working with powered-on electrical equipment;
keep the other hand in your pocket or behind your back.
Remember: There must be a complete circuit to cause electrical shock. By
observing the above rule, you may prevent a current from passing through
your body.
– When using testers, set the controls correctly and use the approved probe
leads and accessories for that tester.
– Stand on suitable rubber mats (obtained locally, if necessary) to insulate you
from grounds such as metal floor strips and machine frames.
Observe the special safety precautions when you work with very high voltages;
these instructions are in the safety sections of maintenance information. Use
extreme care when measuring high voltages.
v Regularly inspect and maintain your electrical hand tools for safe operational
condition.
v Do not use worn or broken tools and testers.
v Never assume that power has been disconnected from a circuit. First, check that it
has been powered-off.

4 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 v Always look carefully for possible hazards in your work area. Examples of these
hazards are moist floors, nongrounded power extension cables, power surges,
and missing safety grounds.
v Do not touch live electrical circuits with the reflective surface of a plastic dental
mirror. The surface is conductive; such touching can cause personal injury and
machine damage.
v Do not service the following parts with the power on when they are removed
from their normal operating places in a machine:
– Power supply units
– Pumps
– Blowers and fans
– Motor generators
and similar units. (This practice ensures correct grounding of the units.)
v If an electrical accident occurs:
– Use caution; do not become a victim yourself.
– Switch off power.
– Send another person to get medical aid.

Safety inspection guide

The intent of this inspection guide is to assist you in identifying potentially unsafe
conditions on these products. Each machine, as it was designed and built, had
required safety items installed to protect users and service personnel from injury.
This guide addresses only those items. However, good judgment should be used to
identify potential safety hazards due to attachment of features or options not
covered by this inspection guide.

If any unsafe conditions are present, you must determine how serious the apparent
hazard could be and whether you can continue without first correcting the
problem.

Consider these conditions and the safety hazards they present:

v Electrical hazards, especially primary power (primary voltage on the frame can
cause serious or fatal electrical shock).
v Explosive hazards, such as a damaged CRT face or bulging capacitor
v Mechanical hazards, such as loose or missing hardware

The guide consists of a series of steps presented in a checklist. Begin the checks
with the power off, and the power cord disconnected.

Checklist:
1. Check exterior covers for damage (loose, broken, or sharp edges).
2. Power-off the computer. Disconnect the power cord.
3. Check the power cord for:
a. A third-wire ground connector in good condition. Use a meter to measure
third-wire ground continuity for 0.1 ohm or less between the external
ground pin and frame ground.
b. The power cord should be the appropriate type as specified in the parts
listings.
c. Insulation must not be frayed or worn.
4. Remove the cover.

Chapter 2. Safety information 5

Downloaded from www.Manualslib.com manuals search engine

 5. Check for any obvious alterations. Use good judgment as to the safety of any
alterations.
6. Check inside the unit for any obvious unsafe conditions, such as metal filings,
contamination, water or other liquids, or signs of fire or smoke damage.
7. Check for worn, frayed, or pinched cables.
8. Check that the power-supply cover fasteners (screws or rivets) have not been
removed or tampered with.

Handling electrostatic discharge-sensitive devices

Any computer part containing transistors or integrated circuits (ICs) should be
considered sensitive to electrostatic discharge (ESD). ESD damage can occur when
there is a difference in charge between objects. Protect against ESD damage by
equalizing the charge so that the machine, the part, the work mat, and the person
handling the part are all at the same charge.
Notes:
1. Use product-specific ESD procedures when they exceed the requirements noted
here.
2. Make sure that the ESD protective devices you use have been certified (ISO
9000) as fully effective.

When handling ESD-sensitive parts:

v Keep the parts in protective packages until they are inserted into the product.
v Avoid contact with other people.
v Wear a grounded wrist strap against your skin to eliminate static on your body.
v Prevent the part from touching your clothing. Most clothing is insulative and
retains a charge even when you are wearing a wrist strap.
v Use the black side of a grounded work mat to provide a static-free work surface.
The mat is especially useful when handling ESD-sensitive devices.
v Select a grounding system, such as those listed below, to provide protection that
meets the specific service requirement.

Note: The use of a grounding system is desirable but not required to protect
against ESD damage.
– Attach the ESD ground clip to any frame ground, ground braid, or green-wire
ground.
– Use an ESD common ground or reference point when working on a
double-insulated or battery-operated system. You can use coax or
connector-outside shells on these systems.
– Use the round ground-prong of the ac plug on ac-operated computers.

Grounding requirements
Electrical grounding of the computer is required for operator safety and correct
system function. Proper grounding of the electrical outlet can be verified by a
certified electrician.

6 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Safety notices (multi-lingual translations)
The caution and danger safety notices in this section are provided in the following
languages:
v English
v Arabic
v Brazilian/Portuguese
v Chinese (simplified)
v Chinese (traditional)
v French
v German
v Hebrew
v Italian
v Korean
v Spanish

DANGER

Electrical current from power, telephone and communication cables is hazardous.

To avoid a shock hazard:

v Do not connect or disconnect any cables or perform installation, maintenance,
or reconfiguration of this product during an electrical storm.
v Connect all power cords to a properly wired and grounded electrical outlet.
v Connect to properly wired outlets any equipment that will be attached to this
product.
v When possible, use one hand only to connect or disconnect signal cables.
v Never turn on any equipment when there is evidence of fire, water, or
structural damage.
v Disconnect the attached power cords, telecommunications systems, networks,
and modems before you open the device covers, unless instructed otherwise
in the installation and configuration procedures.
v Connect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.

To Connect To Disconnect

1. Turn everything OFF. 1. Turn everything OFF.

2. First, attach all cables to devices. 2. First, remove power cords from outlet.
3. Attach signal cables to connectors. 3. Remove signal cables from connectors.
4. Attach power cords to outlet. 4. Remove all cables from devices.
5. Turn device ON.

Chapter 2. Safety information 7

Downloaded from www.Manualslib.com manuals search engine

 CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode if
not properly used, handled, or disposed of.

Do not:
v Throw or immerse into water
v Heat to more than 100°C (212°F)
v Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

CAUTION:
When laser products (such as CD-ROMs, DVD-ROM drives, fiber optic devices,
or transmitters) are installed, note the following:
v Do not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable parts
inside the device.
v Use of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.

DANGER: Some laser products contain an embedded Class 3A or Class 3B laser

diode. Note the following:

Laser radiation when open. Do not stare into the beam, do not view
directly with optical instruments, and avoid direct exposure to the
beam.

≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)

CAUTION:
Use safe practices when lifting.

8 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current from
the device, ensure that all power cords are disconnected from the power source.

2
1

Chapter 2. Safety information 9

Downloaded from www.Manualslib.com manuals search engine

 10 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2. Safety information 11

Downloaded from www.Manualslib.com manuals search engine

 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)

2
1

12 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 PERIGO

A corrente elétrica proveniente de cabos de alimentação, de telefone e de

comunicações é perigosa.

Para evitar risco de choque elétrico:

v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção
ou reconfiguração deste produto durante uma tempestade com raios.
v Conecte todos os cabos de alimentação a tomadas elétricas corretamente
instaladas e aterradas.
v Todo equipamento que for conectado a este produto deve ser conectado a
tomadas corretamente instaladas.
v Quando possível, utilize apenas uma das mãos para conectar ou desconectar
cabos de sinal.
v Nunca ligue nenhum equipamento quando houver evidência de fogo, água ou
danos estruturais.
v Antes de abrir tampas de dispositivos, desconecte cabos de alimentação,
sistemas de telecomunicação, redes e modems conectados, a menos que
especificado de maneira diferente nos procedimentos de instalação e
configuração.
v Conecte e desconecte os cabos conforme descrito na tabela apresentada a seguir
ao instalar, mover ou abrir tampas deste produto ou de dispositivos conectados.

Para Conectar: Para Desconectar:

1. DESLIGUE Tudo. 1. DESLIGUE Tudo.

2. Primeiramente, conecte todos os cabos 2. Primeiramente, remova os cabos de
aos dispositivos. alimentação das tomadas.
3. Conecte os cabos de sinal aos 3. Remova os cabos de sinal dos conectores.
conectores. 4. Remova todos os cabos dos dispositivos.
4. Conecte os cabos de alimentação às
tomadas.
5. LIGUE os dispositivos.

Chapter 2. Safety information 13

Downloaded from www.Manualslib.com manuals search engine

 CUIDADO:

Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça
33F8354 ou um tipo de bateria equivalente recomendado pelo Se o seu sistema
possui um módulo com uma bateria de lítio, substitua-o apenas por um módulo
do mesmo tipo e do mesmo fabricante. A bateria contém lítio e pode explodir se
não for utilizada, manuseada ou descartada de maneira correta.

Não:
v Jogue ou coloque na água
v Aqueça a mais de 100°C (212°F)
v Conserte nem desmonte

Descarte a bateria conforme requerido pelas leis ou regulamentos locais.

PRECAUCIÓN:

Quando produtos a laser (como unidades de CD-ROMs, unidades de DVD-ROM,

dispositivos de fibra ótica ou transmissores) estiverem instalados, observe o
seguinte:
v Não remova as tampas. A remoção das tampas de um produto a laser pode
resultar em exposição prejudicial à radiação de laser. Não existem peças que
podem ser consertadas no interior do dispositivo.
v A utilização de controles ou ajustes ou a execução de procedimentos diferentes
dos especificados aqui pode resultar em exposição prejudicial à radiação.

PERIGO

Alguns produtos a laser contêm diodo de laser integrado da Classe 3A ou da

Classe 3B. Observe o seguinte:

Radiação a laser quando aberto. Não olhe diretamente para o feixe a olho nu ou
com instrumentos ópticos e evite exposição direta ao feixe.

≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)

CUIDADO:

Utilize procedimentos de segurança para levantar equipamentos.

14 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CUIDADO:

O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da

fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O
dispositivo também pode ter mais de um cabo de alimentação. Para remover toda
a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação
estejam desconectados da fonte de alimentação.

2
1

Chapter 2. Safety information 15

Downloaded from www.Manualslib.com manuals search engine

 16 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 2
1

Chapter 2. Safety information 17

Downloaded from www.Manualslib.com manuals search engine

 18 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 2
1

Chapter 2. Safety information 19

Downloaded from www.Manualslib.com manuals search engine

 DANGER

Le courant électrique provenant de l’alimentation, du téléphone et des câbles de

transmission peut présenter un danger.

Pour éviter tout risque de choc électrique :

v Ne manipulez aucun câble et n’effectuez aucune opération d’installation,
d’entretien ou de reconfiguration de ce produit au cours d’un orage.
v Branchez tous les cordons d’alimentation sur un socle de prise de courant
correctement câblé et mis à la terre.
v Branchez sur des socles de prise de courant correctement câblés tout équipement
connecté à ce produit.
v Lorsque cela est possible, n’utilisez qu’une seule main pour connecter ou
déconnecter les câbles d’interface.
v Ne mettez jamais un équipement sous tension en cas d’incendie ou d’inondation,
ou en présence de dommages matériels.
v Avant de retirer les carters de l’unité, mettez celle-ci hors tension et déconnectez
ses cordons d’alimentation, ainsi que les câbles qui la relient aux réseaux, aux
systèmes de télécommunication et aux modems (sauf instruction contraire
mentionnée dans les procédures d’installation et de configuration).
v Lorsque vous installez, que vous déplacez, ou que vous manipulez le présent
produit ou des périphériques qui lui sont raccordés, reportez-vous aux
instructions ci-dessous pour connecter et déconnecter les différents cordons.

Connexion Déconnexion

1. Mettez les unités HORS TENSION. 1. Mettez les unités HORS TENSION.
2. Commencez par brancher tous les 2. Débranchez les cordons d’alimentation
cordons sur les unités. des prises.
3. Branchez les câbles d’interface sur des 3. Débranchez les câbles d’interface des
connecteurs. connecteurs.
4. Branchez les cordons d’alimentation sur 4. Débranchez tous les câbles des unités.
des prises.
5. Mettez les unités SOUS TENSION.

20 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 ATTENTION:

Remplacer la pile au lithium usagée par une pile de référence identique

exclusivement, (référence 33F8354), ou suivre les instructions du fabricant qui en
définit les équivalences. Si votre système est doté d’un module contenant une
pile au lithium, vous devez le remplacer uniquement par un module identique,
produit par le même fabricant. La pile contient du lithium et peut exploser en
cas de mauvaise utilisation, de mauvaise manipulation ou de mise au rebut
inappropriée.

Ne pas :
v la jeter à l’eau,
v l’exposer à des températures supérieures à 100°C,
v chercher à la réparer ou à la démonter.

Ne pas mettre la pile à la poubelle. Pour la mise au rebut, se reporter à la

réglementation en vigueur.

ATTENTION:

Si des produits à laser (tels que des unités de CD-ROM, de DVD-ROM, des
unités à fibres optiques, ou des émetteurs) sont installés, prenez connaissance
des informations suivantes :
v Ne retirez pas le carter. En ouvrant l’unité de CD-ROM ou de DVD-ROM,
vous vous exposez au rayonnement dangereux du laser. Aucune pièce de
l’unité n’est réparable.
v Pour éviter tout risque d’exposition au rayon laser, respectez les consignes de
réglage et d’utilisation des commandes, ainsi que les procédures décrites dans
le présent manuel.

DANGER

Certains produits à laser contiennent une diode à laser intégrée de classe 3A ou

3B. Prenez connaissance des informations suivantes:

Rayonnement laser lorsque le carter est ouvert. Evitez toute expositiondirecte au

rayon laser. Evitez de regarder fixement le faisceau ou del’observer à l’aide
d’instruments optiques.

Chapter 2. Safety information 21

Downloaded from www.Manualslib.com manuals search engine

 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs)

ATTENTION:

Soulevez la machine avec précaution.

ATTENTION:

L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc

d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre,
le système peut être équipé de plusieurs cordonsd’alimentation. Pour mettre
l’unité hors tension, vous devez déconnectertous les cordons de la source
d’alimentation.

2
1

22 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 VORSICHT

An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen.

Aus Sicherheitsgründen:
v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner
keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen.
v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem
Schutzkontakt anschließen.
v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit
ordnungsgemäß geerdetem Schutzkontakt anschließen.
v Die Signalkabel nach Möglichkeit einhändig anschließen oder lösen, um
einen Stromschlag durch Berühren von Oberflächen mit unterschiedlichem
elektrischem Potenzial zu vermeiden.
v Geräte niemals einschalten, wenn Hinweise auf Feuer, Wasser oder
Gebäudeschäden vorliegen.
v Die Verbindung zu den angeschlossenen Netzkabeln,
Telekommunikationssystemen, Netzwerken und Modems ist vor dem Öffnen
des Gehäuses zu unterbrechen, sofern in den Installations- und
Konfigurationsprozeduren keine anders lautenden Anweisungen enthalten
sind.
v Zum Installieren, Transportieren und Öffnen der Abdeckungen des
Computers oder der angeschlossenen Einheiten die Kabel gemäß der
folgenden Tabelle anschließen und abziehen.

Zum Anschließen der Kabel gehen Sie Zum Abziehen der Kabel gehen Sie wie
wie folgt vor folgt vor

1. Schalten Sie alle Einheiten AUS. 1. Schalten Sie alle Einheiten AUS.
2. Schließen Sie erst alle Kabel an die 2. Ziehen Sie zuerst alle Netzkabel aus den
Einheiten an. Netzsteckdosen.
3. Schließen Sie die Signalkabel an die 3. Ziehen Sie die Signalkabel aus den
Buchsen an. Buchsen.
4. Schließen Sie die Netzkabel an die 4. Ziehen Sie alle Kabel von den Einheiten
Steckdose an. ab.
5. Schalten Sie die Einheit EIN.

Chapter 2. Safety information 23

Downloaded from www.Manualslib.com manuals search engine

 CAUTION:

Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer
33F8354 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen.
Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein
Modul desselben Typs und von demselben Hersteller ersetzen. Die Batterie enthält
Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung
explodieren.

Die Batterie nicht:

v mit Wasser in Berührung bringen.
v über 100 C erhitzen.
v reparieren oder zerlegen.

Die örtlichen Bestimmungen für die Entsorgung von Sondermüll beachten.

ACHTUNG:

Bei der Installation von Lasergeräten (wie CD-ROM-Laufwerken, DVD-

aufwerken, Einheiten mit Lichtwellenleitertechnik oder Sendern) Folgendes
beachten:
v Die Abdeckungen nicht entfernen. Durch Entfernen der Abdeckungen des
Lasergeräts können gefährliche Laserstrahlungen freigesetzt werden. Das
Gerät enthält keine zu wartenden Teile.
v Werden Steuerelemente, Einstellungen oder Durchführungen von Prozeduren
anders als hier angegeben verwendet, kann gefährliche Laserstrahlung
auftreten.

VORSICHT

Einige Lasergeräte enthalten eine Laserdiode der Klasse 3A oder 3B. Beachten
Sie Folgendes:

Laserstrahlung bei geöffneter Verkleidung. Nicht in den Strahl blicken. Keine

Lupen oder Spiegel verwenden. Strahlungsbereich meiden.

24 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 ≥18 kg ≥32 kg ≥55 kg

ACHTUNG:

Arbeitsschutzrichtlinien beim Anheben der Maschine beachten.

ACHTUNG:

Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung
für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren
Netzkabeln ausgestattet sein. Um die Stromversorgung für die Einheit
vollständig zu unterbrechen, müssen alle zum Gerät führenden Netzkabel vom
Netz getrennt werden.

2
1

Chapter 2. Safety information 25

Downloaded from www.Manualslib.com manuals search engine

 26 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 2. Safety information 27

Downloaded from www.Manualslib.com manuals search engine

 2
1

28 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 PERICOLO

La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di

comunicazione può essere pericolosa.

Per evitare il rischio di scosse elettriche:

v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la
manutenzione o la riconfigurazione del prodotto durante un temporale.
v Collegare tutti i fili elettrici a una presa di alimentazione correttamente
cablata e dotata di messa a terra.
v Collegare alle prese elettriche appropriate tutte le apparecchiature che
verranno utilizzate per questo prodotto.
v Se possibile, utilizzare solo una mano per collegare o scollegare i cavi di
segnale.
v Non accendere assolutamente apparecchiature in presenza di incendi, perdite
d’acqua o danno strutturale.
v Scollegare i cavi di alimentazione, i sistemi di telecomunicazione, le reti e il
modem prima di aprire i coperchi del dispositivo, salvo istruzioni contrarie
relative alle procedure di installazione e configurazione.
v Collegare e scollegare i cavi come descritto nella seguente tabella quando
vengono effettuate operazioni di installazione, spostamento o apertura dei
coperchi di questo prodotto o delle unità collegate.

Per collegarsi Per scollegarsi

1. SPEGNERE le apparecchiature. 1. SPEGNERE le apparecchiature.

2. Innanzitutto, collegare tutti i cavi alle 2. Innanzitutto, rimuovere i cavi di
unità. alimentazione dalla presa.
3. Collegare i cavi di segnale ai connettori. 3. Rimuovere i cavi di segnale dai
4. Collegare i cavi di alimentazione alla connettori.
presa. 4. Rimuovere tutti i cavi dalle unità.
5. Accendere l’unità.

Chapter 2. Safety information 29

Downloaded from www.Manualslib.com manuals search engine

 ATTENZIONE:

Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 33F8354

o un tipo di batteria equivalente consigliato dal produttore. Se sul sistema è
presente un modulo che contiene una batteria al litio, sostituirlo solo con un
tipo di modulo dello stesso tipo della stessa casa di produzione. La batteria
contiene litio e può esplodere se usata, maneggiata o smaltita in modo non
corretto.

Non:
v Gettare o immergere la batteria nell’acqua
v Riscaldarla ad una temperatura superiore ai 100 gradi C (212 gradi F)
v Smontarla, ricaricarla o tentare di ripararla

Le batterie usate vanno smaltite in accordo alla normativa in vigore (DPR 915/82
e successive disposizioni e disposizioni locali).

ATTENZIONE:

Quando vengono installati prodotti laser (quali CD-ROM, unità DVD-ROM,

unità a fibre ottiche o trasmittenti), tener presente quanto segue:
v Non rimuovere gli sportelli. L’apertura di un’unità laser può determinare
l’esposizione a radiazioni laser pericolose. All’interno dell’unità non vi sono
parti su cui effettuare l’assistenza tecnica.
v L’utilizzo di controlli, regolazioni o l’esecuzione di procedure non descritti nel
presente manuale possono provocare l’esposizione a radiazioni pericolose.

PERICOLO

Alcune unità laser contengono un diodo laser di Classe 3A o Classe 3B. Tener
presente quanto segue:

Aprendo l’unità vengono emesse radiazioni laser. Non fissare il fascio, non
guardarlo direttamente con strumenti ottici ed evitare l’esposizione al fascio.

30 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 ≥18 kg ≥32 kg ≥55 kg

ATTENZIONE:

Prestare attenzione nel sollevare l’apparecchiatura.

ATTENZIONE:

Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore

dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’
possibile che l’unità disponga di più cavi di alimentazione. Per disattivare
l’alimentazione dall’unità, accertarsi che tutti i cavi di alimentazione siano
scollegati dalla fonte di alimentazione.

2
1

Chapter 2. Safety information 31

Downloaded from www.Manualslib.com manuals search engine

 32 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 2
1

Chapter 2. Safety information 33

Downloaded from www.Manualslib.com manuals search engine

 PELIGRO

La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de

comunicación puede ser peligrosa.

Para evitar el riesgo de descarga eléctrica:

v No conecte ni desconecte los cables ni realice ninguna tarea de instalación,
mantenimiento o reconfiguración de este producto durante una tormenta
eléctrica.
v Conecte todos los cables de alimentación a tomas de corriente debidamente
cableadas y conectadas a tierra.
v Cualquier equipo que se conecte a este producto también debe conectarse a
tomas de corriente debidamente cableadas.
v Siempre que sea posible, utilice una sola mano para conectar o desconectar los
cables de señal.
v No encienda nunca un equipo cuando hay señales de fuego, agua o daños
estructurales.
v Desconecte los cables de alimentación, los sistemas de telecomunicaciones, las
redes y los módems conectados antes de abrir las cubiertas de los dispositivos,
a menos que se indique lo contrario en los procedimientos de instalación y
configuración.
v Conecte y desconecte los cables, como se describe en la tabla siguiente,
cuando instale, mueva o abra las cubiertas de este producto o de los
dispositivos conectados.

Para conectar Para desconectar

1. APÁGUELO todo. 1. APÁGUELO todo.

2. En primer lugar, conecte todos los 2. En primer lugar, desenchufe los cables de
cables a los dispositivos. alimentación de las tomas de corriente.
3. Conecte los cables de señal a los 3. Desconecte los cables de señal de los
conectores. conectores.
4. Enchufe los cables de alimentación a las 4. Desconecte todos los cables de los
tomas de corriente. dispositivos.
5. Encienda el dispositivo.

34 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 PRECAUCIÓN:

Cuando sustituya una batería de litio, utilice solamente una batería número de
pieza 33F8354 u otra de tipo equivalente recomendada por el fabricante. Si su
sistema dispone de un módulo que contiene una batería de litio, reemplácelo
sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene
litio y puede explotar si no se utiliza, manipula o desecha correctamente.

No debe:
v Arrojarla al agua o sumergirla en ella
v Exponerla a temperaturas superiores a 100°C (212°F)
v Repararla o desmontarla

Deshágase de la batería según especifiquen las leyes o normas locales.

PRECAUCIÓN:

Cuando haya productos láser (como unidades de CD-ROM, unidades de DVD,

dispositivos de fibra óptica o transmisores) instalados, tenga en cuenta lo
siguiente:
v No quite las cubiertas. Si quita las cubiertas del producto láser, podría quedar
expuesto a radiación láser peligrosa. Dentro del dispositivo no existe ninguna
pieza que requiera servicio técnico.
v Si usa controles o ajustes o realiza procedimientos que no sean los
especificados aquí, podría exponerse a radiaciones peligrosas.

PELIGRO

Algunos productos láser tienen incorporado un diodo láser de clase 3A o clase

3B. Tenga en cuenta lo siguiente:

Cuando se abre, queda expuesto a radiación láser. No mire directamente al rayo

láser, ni siquiera con instrumentos ópticos, y evite exponerse directamente al
rayo láser.

Chapter 2. Safety information 35

Downloaded from www.Manualslib.com manuals search engine

 ≥18 kg ≥32 kg ≥55 kg

PRECAUCIÓN:

Adopte procedimientos seguros al levantar el equipo.

PRECAUCIÓN:

El botón de control de alimentación del dispositivo y el interruptor de

alimentación de la fuente de alimentación no desconectan la corriente eléctrica
suministrada al dispositivo. Además, el dispositivo podría tener más de un cable
de alimentación. Para suprimir toda la corriente eléctrica del dispositivo,
asegúrese de que todos los cables de alimentación estén desconectados de la
toma de corriente.

2
1

36 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 3. General information
This chapter provides general information that applies to all machine types
supported by this publication.

The Lenovo Care program

Use the Lenovo Care program for general information about the use, operation,
and maintenance of the computer. The Lenovo Care program also contains
information to help solve problems and get repair service or other technical
assistance. The Lenovo Care program is preinstalled on most Lenovo 3000 J Series
products.

Additional information resources

If you have Internet access, the most up-to-date information for the computer is
available from the World Wide Web.

You can find the following information:

v CRU removal and installation instructions
v Publications
v Troubleshooting information
v Parts information
v Downloads and drivers
v Links to other useful sources of information

To access this information, point your browser to http://www.lenovo.com/

support/.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 37

Downloaded from www.Manualslib.com manuals search engine

 Specifications
This section lists the physical specifications for the computer.

Machine types 7387, 7388, 7389, 7393, 7394, and 7395

Dimensions
Width: 180 mm (7.09 in.)
Height: 392 mm (15.43 in.)
Depth: 445 mm (17.52 in.)
Weight
Minimum configuration as shipped: 9.1kg (20.06 lbs)
Maximum configuration: 10.2 kg (22.5 lbs)
Environment
Air temperature:
System on: 10° to 35°C (50° to 95°F)
System off: 10° to 60°C (50° to 140°F)
Maximum altitude: 914 m (3000 ft)
Note: The maximum altitude, 914 m (3000 ft), is the maximum altitude at which the specified air
temperatures apply. At higher altitudes, the maximum air temperatures are lower than those specified.
Humidity:
System on: 10% to 80%
System off: 10% to 90%
Electrical input
Input voltage:
Low range:
Minimum: 100V ac
Maximum: 127V ac
Input frequency: 50-60 Hz
Voltage switch setting: 115V ac
High range:
Minimum: 200V ac
Maximum: 240V ac
Input frequency: 50-60 Hz
Voltage switch setting: 230V ac
Input kilovolt-amperes (kVA) (approximate):
Minimum configuration as shipped: 0.158 kVA
Maximum configuration: 0.213 kVA

38 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Machine types 7390, 7391, 7392, 7396, 7397, and 7398
This section lists the physical specifications for the computer.

Dimensions
Width: 331 mm (13.0 in.)
Height: 108 mm (4.3 in.)
Depth: 405 mm (15.9 in.)
Weight
Minimum configuration as shipped: 8.2 kg (18.0 lbs)
Maximum configuration: 8.3 kg (18.2 lbs)
Environment
Air temperature:
Operating at 0 - 3000 ft (914.4 m): 10° to 35°C (50° to 95°F)
Operating at 3000 ft - 7000 ft (2134 m): 10° to 32°C (50° to 89.6°F)
Non-operating: 10° to 43°C (50° to 110°F)
Humidity:
Operating: 10% to 80%
Non-operating: 10% to 90%
Transit: 8% to 90%
Maximum altitude: 7000 ft (2133.6 m)
Electrical input
Input voltage:
Low range:
Minimum: 100V ac
Maximum: 127V ac
Input frequency: 50/60 Hz
Voltage switch setting: 115V ac
High range:
Minimum: 200V ac
Maximum: 240V ac
Input frequency: 50/60 Hz
Voltage switch setting: 230V ac
Input kilovolt-amperes (kVA) (approximate):
Minimum configuration as shipped: 0.09 kVA
Maximum configuration: 0.23 kVA

Chapter 3. General information 39

Downloaded from www.Manualslib.com manuals search engine

 40 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 4. General Checkout
Attention
The drives in the computer you are servicing might have been rearranged or
the drive startup sequence changed. Be extremely careful during write
operations such as copying, saving, or formatting. Data or programs can be
overwritten if you select an incorrect drive.

General error messages appear if a problem or conflict is found by an application

program, the operating system, or both. For an explanation of these messages, refer
to the information supplied with that software package.

Before replacing any FRUs, ensure that the latest level of BIOS is installed on the
system. A down-level BIOS might cause false errors and unnecessary replacement
of the system board. For more information on how to determine and obtain the
latest level BIOS, see “BIOS levels” on page 207.

Use the following procedure to help determine the cause of the problem:
1. Power-off the computer and all external devices.
2. Check all cables and power cords.
3. Set all display controls to the middle position.
4. Power-on all external devices.
5. Power-on the computer.
v Look for displayed error codes
v Listen for beep codes
v Look for readable instructions or a main menu on the display.
If you did not receive the correct response, proceed to step 6.
If you do receive the correct response, proceed to step 7.
6. Look at the following conditions and follow the instructions:
v If you hear beep codes during POST, go to “Beep symptoms” on page 77.
v If the computer displays a POST error, go to “POST error codes” on page 78.
v If the computer hangs and no error is displayed, continue at step 7.
7. Run the Diagnostic programs. See Chapter 5, “Diagnostics,” on page 43.
v If you receive an error, replace the part that the diagnostic program calls out
or go to “Diagnostic error codes” on page 56.
v If the test stops and you cannot continue, replace the last device tested.

Problem determination tips

Due to the variety of hardware and software combinations that can be
encountered, use the following information to assist you in problem determination.
If possible, have this information available when requesting assistance from Service
Support and Engineering functions.
v Machine type and model
v Processor or hard disk upgrades
v Failure symptom
– Do diagnostics indicate a failure?

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 41

Downloaded from www.Manualslib.com manuals search engine

 – What, when, where, single, or multiple systems?
– Is the failure repeatable?
– Has this configuration ever worked?
– If it has been working, what changes were made prior to it failing?
– Is this the original reported failure?
v Diagnostics version
– Type and version level
v Hardware configuration
– Print (print screen) configuration currently in use
– BIOS level
v Operating system software
– Type and version level

Note: To eliminate confusion, identical systems are considered identical only if

they:
1. Are the exact machine type and models
2. Have the same BIOS level
3. Have the same adapters/attachments in the same locations
4. Have the same address jumpers/terminators/cabling
5. Have the same software versions and levels
6. Have the same Diagnostic Diskettes (version)
7. Have the same configuration options set in the system
8. Have the same setup for the operating system control files

Comparing the configuration and software set-up between “working and

non-working” systems will often lead to problem resolution.

42 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 5. Diagnostics
Diagnostic programs are used to test hardware components of the computer and
report operating-system-controlled settings that can cause hardware failures. There
are two diagnostic programs preinstalled on the computer to help diagnose
problems:
v PC-Doctor for Windows (used when diagnosing problems while running the
Windows operating system)
v PC-Doctor for DOS or PC-Doctor for Windows PE, depending upon your
machine type and model (used when your Windows operating system will not
start)
Notes:
1. You can download the latest version of the PC-Doctor for Windows and
PC-Doctor for DOS diagnostic programs from http://www.lenovo.com/
support/. Type your machine type into the Use Quick Path field and click Go
to find the downloadable files that are specific to the computer.
2. Log files are created when you run PC-Doctor for Windows and depending
upon your machine type and model, PC-Doctor for DOS or PC-Doctor for
Windows PE. Save and print the log files created by both diagnostic programs.
The log file created by PC-Doctor for Windows is automatically saved in
C:\PCDR\DETAILED.TXT.

PC-Doctor for Windows

PC-Doctor for Windows is a diagnostic program that works through the Windows
operating system. The PC-Doctor for Windows diagnostic program enables you to
view symptoms and solutions for computer problems, access the Lenovo
troubleshooting center, update system drivers, and review system information.

To run PC-Doctor for Windows, open the Start menu from the Windows desktop,
select All Programs, select PC-Doctor for Windows, and click PC-Doctor for
Windows. Follow the instructions on the screen. For additional information about
running the diagnostic program, refer to the PC-Doctor for Windows help system.

If you still suspect a problem after PC-Doctor for Windows runs successfully, run
PC-Doctor for DOS or PC-Doctor for Windows PE to help you diagnose the
computer problem.

PC-Doctor for DOS

Depending upon your machine type and model, you either have
PC-Doctor for DOS or PC-Doctor for Windows PE on each Lenovo computer. The
PC-Doctor for DOS diagnostic program is part of the Rescue and Recovery
workspace and runs independently of the Windows operating system. Use
PC-Doctor for DOS, if you are unable to start the Windows operating system or if
PC-Doctor for Windows has not been successful in isolating a possible problem.
You can run PC-Doctor for DOS from a diagnostic CD image or diagnostic
diskettes that have been created. You can also run PC-Doctor for DOS from the
Rescue and Recovery workspace.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 43

Downloaded from www.Manualslib.com manuals search engine

 Note: It is important to create a diagnostic CD image or diagnostic diskettes in
case PC-Doctor for DOS cannot be run from the Rescue and Recovery
workspace.

Creating a diagnostic CD image

To create a diagnostic CD image, download a self-starting bootable CD image
(known as an .iso image) of the diagnostic program from http://
www.lenovo.com/support/. After you download the image, you can create the CD
using any CD burning software.

If the computer does not have a CD burner or you do not have Internet access, see
“Creating diagnostic diskettes.”

Creating diagnostic diskettes

To create diagnostic diskettes, download the PC-Doctor for DOS diagnostic
program from http://www.lenovo.com/support/ onto two blank, formatted
diskettes.

If you do not have Internet access, create the diagnostic diskettes using the
following procedure:

Note: You will need a diskette drive on the computer or a USB diskette drive to
complete this procedure.
1. Shut down the operating system and turn off the computer.
2. If you are using a USB diskette drive, plug it into the computer.
3. Repeatedly press and release the F11 key as you turn on the computer.
4. When you hear beeps or see a logo screen, stop pressing the F11 key. The
Rescue and Recovery workspace opens.

Note: For some models, press the Esc key to enter Rescue and Recovery.
5. From the Rescue and Recovery workspace, select Create diagnostic disks.
6. Follow the instructions on the screen.
7. When prompted, insert a blank, formatted diskette into the diskette drive and
continue to follow the instructions on the screen.
8. When the operation is complete, remove the diskette and click Quit.
9. Insert another blank, formatted diskette into the diskette drive and continue to
follow the instructions on the screen.
10. When the operation is complete, remove the diskette and click Quit.

Running diagnostics from the CD or diskettes

1. If you are running diagnostics from diskettes using a USB diskette drive, plug
in the USB drive.

Note: The optical drive or diskette drive must be selected in the startup
sequence. See“Changing the startup device sequence” on page 53 for
instructions on how to select the startup device.
2. Insert the CD or diskette.
3. Restart the computer.
4. When the diagnostics program opens, follow the instructions on the screen.

44 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Note: If you are running diagnostics from a diskette, when prompted, remove
the first diskette and insert the second diskette.
5. Select the diagnostic test you want to run. Press the F1 key for additional help.
6. Remove the CD or diskette when the program finishes.

Running diagnostics from the Rescue and Recovery

workspace
If you do not have a diagnostic CD image or diagnostic diskette, you can run the
PC-Doctor for DOS diagnostic program from the Rescue and Recovery workspace.
To run diagnostics from the Rescue and Recovery workspace, use the following
procedure:
1. Shut down the operating system and turn off the computer.
2. Repeatedly press and release the F11 key as you turn on the computer.
3. When you hear beeps or see a logo screen, stop pressing the F11 key. The
Rescue and Recovery workspace opens.

Note: For some models, press the Esc key to enter Rescue and Recovery.
4. From the Rescue and Recovery workspace, select Diagnose hardware.
5. Follow the prompts on the screen. The computer will reboot.
6. When the computer restarts, the diagnostic program opens automatically. Select
the diagnostic test you want to run. Press the F1 key for additional help.

PC-Doctor for Windows PE

Depending upon your machine type and model, you either have PC-Doctor for
DOS or PC-Doctor for Windows PE on each Lenovo computer. The PC-Doctor for
Windows PE diagnostic program is part of the Rescue and Recovery workspace.
Use PC-Doctor for Windows PE, if you are unable to start the Windows operating
system or if PC-Doctor for Windows has not been successful in isolating a possible
problem.

Running diagnostics from the Rescue and Recovery

workspace
You can run the PC-Doctor for Windows PE diagnostic program from the Rescue
and Recovery workspace. To run diagnostics from the Rescue and Recovery
workspace, use the following procedure:
1. Shut down the operating system and turn off the computer.
2. Repeatedly press and release the F11 key as you turn on the computer.
3. When you hear beeps or see a logo screen, stop pressing the F11 key. The
Rescue and Recovery workspace opens.
4. From the Rescue and Recovery workspace, select Diagnose hardware.
5. The diagnostic program opens automatically. Select the diagnostic test you
want to run. Press the F1 key for additional help.
6. Follow the instructions on the screen.

Note: Rescue media includes PC-Doctor for Windows PE. For more information
about rescue media, see the User Guide for the computer.

Chapter 5. Diagnostics 45

Downloaded from www.Manualslib.com manuals search engine

 Navigating through the diagnostics programs
Use the cursor movement keys to navigate within the menus.
v The Enter key is used to select a menu item.
v The Esc key is used to back up to the previous menu.
v For online help select F1.

Running tests
There are four ways to run the diagnostic tests.
v Using the cursor movement keys, highlight Run Normal Test or Run Quick Test
from the Diagnostics menu and then press Enter.
This automatically runs a pre-defined group of tests from each test category.
Run Normal Test runs a more extensive set of tests than does Run Quick Test
and takes longer to complete.
v Press F5 to automatically run all selected tests in all categories.
v From within a test category, press Ctrl-Enter to automatically run only the
selected tests in that category.
v Using the cursor movement keys, highlight a single test within a test category,
and then press Enter. This runs only that test.

Press Esc at any time to stop the testing process.

Test results (N/A, PASSED, FAILED, ABORTED) are displayed in the field beside
the test description and in the test log. See “Viewing the test log” on page 49.

To select one or more tests, use the following procedure.

1. Open the corresponding test category.
2. Using the cursor movement keys, highlight the desired test.
3. Press the space bar.
A selected test is marked by >>. Pressing the space bar again de-selects a test
and removes the >>.
4. Repeat steps 2 and 3 above to select all desired tests.

Test results
Diagnostics test results produce the following error code format:

Function Failure Type DeviceID Date ChkDigits Text

Code

v Function Code:
Represents the feature or function within the PC.
v Failure Type:
Represents the type of error encountered.
v DeviceID:
Contains the component’s unit-ID which corresponds to either a fixed disk
drive, removable media drive, serial or parallel port, processor, specific RIMM,
or a device on the PCI bus.
v Date:

46 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Contains the date when the diagnostic test was run. The date is retrieved from
CMOS and displayed using the YYYYMMDD format.
v ChkDigits:
Contains a 2-digit check-digit value to ensure the following:
– Diagnostics were run on the specified date.
– Diagnostics were run on the specified computer.
– The diagnostic error code is recorded correctly.
v Text:
Description of the error.

Note: See “Diagnostic error codes” on page 56 for error code listings.

Fixed disk advanced test (FDAT)

PC-Doctor Fixed-Disk1 Advanced Test module (FDAT) is a full-featured highly
configurable fixed-disk test suite. The configurable capabilities of FDAT allow
users to enable or disable specific tests, enable or disable testing features, control
the test log detail, alter testing parameters, and so on. FDAT tests for and reports
most commonly found errors on a fixed-disk drive and is able to test up to 128
SCSI and 4 IDE drives (up to 132 total drives).

Drive information is gathered through FDAT’s enumeration of available devices

and user specific configuration parameters located in the FDAT.INI. FDAT uses
information supplied by these features to indicate specifically what devices are
available for test, what tests are available for the device, device properties, and so
on. To change testing parameters, you modify the FDAT.INI file in PC Doctor for
DOS.

FDAT consists of the following subtests and features.

Fixed-Disk Tests:
v Seek Tests: - checks the physical operation of the drive head.
– Linear Seek
– Random Seek
– Min-Max Seek
– Butterfly Seek
v Verify Tests: - checks the integrity of the data present on the media.
– Linear Verify
– Random Verify
v Surface Scan Tests: - checks the drive media for defects.
– Surface Scan (Linear)
– Surface Scan (Aggressive) - this is disabled for normal customer use.
– Surface Scan (Random)
v Self-monitoring, Analysis and Reporting Technology (SMART) - checks the
SMART functionality for drives that support SMART.
– Start SMART Self-Test

Other Test Features:

1. The terms fixed disk and hard disk are used interchangeably.

Chapter 5. Diagnostics 47

Downloaded from www.Manualslib.com manuals search engine

 v Write-Splice Repair - detects and corrects Error Correction Code errors during
Verify tests.
v Auto Spin Down - a gradual spin down of the drive platters to avoid damaging
the media.
v Manufacturer Log - an in-depth manufacturer supported log of errors on the
drive.

Multitasking:

To allow simultaneous testing of multiple hard drives whenever possible, the

FDAT module is written as a set of multitasking functions. Each drive under test
can run the same test or run a different test at the same time. Each subtest is
written to handle a single test pass and all test variables are kept track of in a
structure unique for each drive.

However, when testing IDE drives, FDAT will not perform simultaneous testing of
IDE drives that are attached to the same IDE cable. For example, if FDAT is testing
four IDE drives on a PC, it will perform simultaneous testing on drives 1 and 3
first (master drives), then perform tests on 2 and 4 (slave drives). FDAT will also
perform simultaneous testing on a master and slave that are on separate IDE
cables, but will not perform simultaneous tests on a master and slave on the same
IDE cable. This generally increases the amount of time needed to test multiple IDE
drives.

Another limitation of FDAT’S multitasking capability is the use of Ultra DMA

(UDMA). Only one drive at a time can access the UDMA channel and the UDMA
channel buffer must be kept high in order to maintain a speed advantage over
other data transfer modes. In order to use the UDMA channel during testing, users
must disable the multitasking feature.

Destructive versus non-destructive testing:

Most of the tests found in FDAT are non-destructive. This means that PC-Doctor
program will preserve any data that is present on the tested media prior to
beginning any destructive operations (such as write operations). However, users
can run certain tests in destructive mode (i.e. surface scan tests). Destructive tests
will speed up testing because FDAT does not preserve the data on the media prior
to the test beginning. Unlike non-destructive tests, any data present on the media
prior to the test beginning is lost.

FDAT allows for enabling or disabling destructive tests, as well as specifying a

range of destructive and non-destructive sectors on the tested drive. This is done
through the configuration of the FDAT.INI. If destructive and non-destructive
ranges somehow overlap, then the overlapped area is considered non-destructive.
For example, if users specify both destructive and non-destructive ranges as the
same, then the entire drive is tested as non-destructive.

Quick and Full erase - hard drive

The diagnostics program offers two hard drive format utilities:
v Quick Erase Hard Drive
v Full Erase Hard Drive

The Quick Erase Hard Drive provides a DOS utility that performs the following:
v Destroys the Master Boot Record (MBR) on the hard drive.

48 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 v Destroys all copies of the FAT Table on all partitions (both the master and
backup).
v Destroys the partition table.
v Provides messages that warn the user that this is a non-recoverable process.

The Full Erase Hard Drive provides a DOS utility that performs the following:
v Performs all the steps in Quick Erase.
v Provides a DOS utility that writes random data to all sectors of the hard drive.
v Provides an estimate of time to completion along with a visual representation of
completion status.
v Provides messages that warn the user about non-recoverable process.

Important: Make sure that all data is backed up before using the Quick or Full Erase
functions.

To select the Quick Erase or Full Erase Hard Drive utility, use the following
procedure:
1. Select the UTILITY option on the toolbar and press Enter.
2. Select either the QUICK ERASE or FULL ERASE HARD DISK option and
follow the instructions.

Viewing the test log

Errors reported by the diagnostic test will be displayed by the program as a failed
test.

To view details of a failure or to view a list of test results, use the following
procedure from any test category screen:
1. Press F3 to activate the log file.
2. Press F3 again to save the file to diskette or press F2 to print the file.

Chapter 5. Diagnostics 49

Downloaded from www.Manualslib.com manuals search engine

 50 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 6. Using the Setup Utility
The Setup Utility program is stored in the electrically erasable programmable
read-only memory (EEPROM) of the computer. The Setup Utility program is used
to view and change the configuration settings of the computer, regardless of which
operating system you are using. However, the operating-system settings might
override any similar settings in the Setup Utility program.

Starting the Setup Utility program

To start the Setup Utility program, do the following:
1. If the computer is already on when you start this procedure, shut down the
operating system and turn off the computer.
2. Press and hold the F1 key then turn on the computer. When you hear multiple
beeps, release the F1 key.
Notes:
a. If you are using a USB keyboard and the Setup Utility program does not
display using this method, repeatedly press and release the F1 key rather
than leaving it pressed when turning on the computer.
b. If a user password or an administrator/supervisor password has been set,
the Setup Utility program menu is not displayed until you type the
password. See “Using passwords” for more information.

The Setup Utility might start automatically when POST detects that hardware has
been removed or new hardware has been installed in the computer.

Viewing and changing settings

The Setup Utility program menu lists items that identify system configuration
topics.

When working with the Setup Utility program menu, you must use the keyboard.
The keys used to perform various tasks are displayed at the bottom of each screen.

Using passwords
Passwords might be set to provide security for the computer and data. There are
two types of passwords: a user password and an administrator or supervisor
password. A password of either type does not have to be set to use the computer.
If either password is set, read the following sections.

User Password
The user password feature deters unauthorized persons from gaining access to the
computer.

Setting, changing, and deleting a user password

To set, change, or delete a user password, do the following:

Note: A password can be any combination of up to eight characters (A- Z, a-z, and
0-9).

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 51

Downloaded from www.Manualslib.com manuals search engine

 1. Start the Setup Utility program (see “Starting the Setup Utility program” on
page 51).
2. From the Setup Utility program menu, select Set User Password and press
Enter.
3. The password dialog box will be displayed. Type the new password, and press
Enter.
4. When prompted to confirm the password, type the password again. If you type
the password in correctly, the password will be installed.

To delete a previously set user password, do the following:

Note: When prompted for a password, you can type either your user or
administrator/supervisor password.
1. From the Setup Utility program menu, select Set User Password and press
Enter. A message will display that indicates the password has been disabled.
2. Press any key to continue.

Administrator or Supervisor Password

Setting an Administrator or Supervisor Password deters unauthorized persons
from changing configuration settings.

After an Administrator or Supervisor Password is set, a password prompt is

displayed each time you try to access the Setup Utility program. If the wrong
password is typed, an error message is displayed. If the wrong password is typed
three times, you must turn the computer off and start again.

If both the user and administrator/supervisor passwords are set, either password
can be typed. However, to change any configuration settings, you must use the
administrator/supervisor password.

Setting, changing, and deleting an administrator/supervisor

password
To set, change, or delete an administrator/supervisor password, do the following:

Note: A password can be any combination of up to eight characters (A- Z, a-z, and
0-9).
1. Start the Setup Utility program (see “Starting the Setup Utility program” on
page 51).
2. From the Setup Utility program menu, select Set Administrator Password or
Set Supervisor Password and press Enter.
3. The password dialog box will be displayed. Type the new password, and press
Enter.
4. When prompted to confirm the password, type the password again. If you type
the password correctly, the password will be installed.

To delete a previously set administrator/supervisor password, do the following:

Note: When prompted for a password, you must type your administrator/
supervisor password.
1. From the Setup Utility program menu, select Set Administrator Password
orSet Supervisor Password and press Enter. A message will display that
indicates the password has been disabled.
2. Press any key to continue.

52 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Selecting a startup device
If the computer does not start up (boot) from a device such as the CD-ROM,
diskette, or hard disk as expected, use one of the following procedures to select a
startup device.

Selecting a temporary startup device

Use this procedure to startup from any boot device.

Note: Not all CDs, hard disks, and diskettes are startable (bootable).
1. Turn off the computer.
2. Press and hold the F12 key then turn on the computer. When the Startup
Device Menu (Boot Menu) appears, release the F12 key.

Note: If you are using a USB keyboard and the Startup Device Menu does not
display using this method, repeatedly press and release the F12 key
rather than leaving it pressed when turning on the computer.
3. Select the desired startup device from the Startup Device Menu and press Enter
to begin.

Note: Selecting a startup device from the Startup Device (Boot) menu does not
permanently change the startup sequence.

Changing the startup device sequence

To view or change the primary or automatic power-on startup sequence, do the
following:
1. Start the Setup Utility program (see “Starting the Setup Utility program” on
page 51).
2. Select Advanced BIOS features.
3. Select the sequence of devices for the First Boot Device, the Second Boot
Device, and the Third Boot Device.
4. Press Esc to return to the Setup Utility program menu.
5. Select Save & Exit Setup.

If you have changed these settings and want to return to the default settings, press
(N) when the Save and Exit dialog box is displayed.

Exiting from the Setup Utility program

When you finish viewing or changing settings, press Esc to return to the Setup
Utility program menu (you might have to press Esc several times). If you want to
save the new settings, select Save & Exit Setup before you exit. Otherwise, your
changes will not be saved.

Chapter 6. Using the Setup Utility 53

Downloaded from www.Manualslib.com manuals search engine

 54 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 7. Symptom-to-FRU Index
The Symptom-to-FRU index lists error symptoms and possible causes. The most
likely cause is listed first. Always begin with Chapter 4, “General Checkout,” on
page 41. This index can also be used to help you decide which FRUs to have
available when servicing a computer. If you are unable to correct the problem
using this index, go to “Undetermined problems” on page 81.

Notes:
v If you have both an error message and an incorrect audio response, diagnose the error
message first.
v If you cannot run the diagnostic tests or you get a diagnostic error code when running a
test, but did receive a POST error message, diagnose the POST error message first.
v If you did not receive any error message, look for a description of your error symptoms
in the first part of this index.

Hard disk drive boot error

A hard disk drive boot error (error codes 1962 and I999030X) can have the
following causes.

Error FRU/Action
The start-up drive is not in the boot Check the configuration and ensure the
sequence in configuration. start-up drive is in the boot sequence.
No operating system installed on the boot Install an operating system on the boot
drive. drive.
The boot sector on the start-up drive is The drive must be formatted, do the
corrupted. following:
1. Attempt to back-up the data on the
failing hard disk drive.
2. Using the operating systems programs,
format the hard disk drive.
The drive is defective. Replace the hard disk drive.

Power Supply Problems

If you suspect a power problem, use the following procedures.

Check/Verify FRU/Action
Check the following for proper installation. Reseat connectors
v Power Cord
v On/Off Switch connector
v On/Off Switch Power Supply connector
v System Board Power Supply connectors
v Microprocessor(s) connection
Check the power cord for continuity. Power Cord
Check the power-on switch for continuity. Power-on Switch

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 55

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic error codes
Refer to the following diagnostic error codes when using the diagnostic tests. See
“Running tests” on page 46 for the specific type for information about the
Diagnostic programs.

In the following index, X can represent any number.

Diagnostic Error Code FRU/Action

000-000-XXX No action
BIOS Test Passed
000-002-XXX 1. Flash the system. See “Flash update
BIOS Timeout procedures” on page 207
2. System board
000-024-XXX 1. Flash the system. See “Flash update
BIOS Addressing test failure procedures” on page 207
2. System board
000-025-XXX 1. Flash the system. See “Flash update
BIOS Checksum Value error procedures” on page 207
2. System board
000-026-XXX 1. Flash the system. See “Flash update
FLASH data error procedures” on page 207
2. System board
000-027-XXX 1. Run Setup
BIOS Configuration/Setup error
2. Flash the system. See “Flash update
procedures” on page 207
3. System board
000-034-XXX 1. Reboot the system
BIOS Buffer Allocation failure
2. Flash the system. See “Flash update
procedures” on page 207
3. Run memory test
4. System board
000-035-XXX 1. Flash the system. See “Flash update
BIOS Reset Condition detected procedures” on page 207
2. System board
000-036-XXX 1. Flash the system. See “Flash update
BIOS Register error procedures” on page 207
2. System board
000-038-XXX 1. Flash the system. See “Flash update
BIOS Extension failure procedures” on page 207
2. Adapter card
3. System board
000-039-XXX 1. Flash the system. See “Flash update
BIOS DMI data error procedures” on page 207
2. System board
000-195-XXX Information only
BIOS Test aborted by user Re-start the test, if necessary

56 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
000-196-XXX 1. Press F3 to review the log file
BIOS test halt, error threshold exceeded
2. Re-start the test to reset the log file
000-197-XXX 1. Make sure the component that is called
BIOS test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
000-198-XXX 1. Make sure the component that is called
BIOS test aborted out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and retest. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
000-199-XXX 1. Go to “Undetermined problems” on page
BIOS test failed, cause unknown 81
2. Flash the system and re-test
3. Replace component under function test
000-250-XXX 1. Flash the system. See “Flash update
BIOS APM failure procedures” on page 207
2. System board
000-270-XXX 1. Flash the system. See “Flash update
BIOS ACPI failure procedures” on page 207
2. System board
001-000-XXX No action
System Test Passed
001-00X-XXX System board
System Error
001-01X-XXX System board
System Error
001-024-XXX System board
System Addressing test failure
001-025-XXX 1. Flash the system. See “Flash update
System Checksum Value error procedures” on page 207
2. System board
001-026-XXX 1. Flash the system. See “Flash update
System FLASH data error procedures” on page 207
2. System board
001-027-XXX 1. Run Setup
System Configuration/Setup error
2. Flash the system. See “Flash update
procedures” on page 207
3. System board

Chapter 7. Symptom-to-FRU Index 57

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
001-032-XXX System board
System Device Controller failure
001-034-XXX 1. Reboot the system
System Device Buffer Allocation failure
2. Flash the system. See “Flash update
procedures” on page 207
3. Run memory test
4. System board
001-035-XXX System board
System Device Reset condition detected
001-036-XXX System board
System Register error
001-038-XXX 1. Adapter card
System Extension failure
2. System board
001-039-XXX 1. Flash the system. See “Flash update
System DMI data structure error procedures” on page 207
2. System board
001-040-XXX 1. Power-off/on system and re-test
System IRQ failure
2. System board
001-041-XXX 1. Power-off/on system and re-test
System DMA failure
2. System board
001-195-XXX Information only
System Test aborted by user Re-start the test, if necessary
001-196-XXX 1. Press F3 to review the log file
System test halt, error threshold exceeded
2. Re-start the test to reset the log file
001-197-XXX 1. Make sure the component that is called
System test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
001-198-XXX 1. If a component is called out, make sure
System test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and retest. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
001-199-XXX 1. Go to “Undetermined problems” on page
System test failed, cause unknown 81
2. Flash the system and re-test
3. Replace component under function test
001-250-XXX System board
System ECC error

58 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
001-254-XXX System board
001-255-XXX
001-256-XXX
001-257-XXX
System DMA error
001-260-XXX System board
001-264-XXX
System IRQ error
001-268-XXX 1. Device on IRQ1
System IRQ1 failure
2. System board
001-269-XXX 1. Device on IRQ2
System IRQ2 failure
2. System board
001-270-XXX 1. Device on IRQ3
System IRQ3 failure
2. System board
001-271-XXX 1. Device on IRQ4
System IRQ4 failure
2. System board
001-272-XXX 1. Device on IRQ5
System IRQ5 failure
2. System board
001-273-XXX 1. Diskette Cable
System IRQ6
2. Diskette drive
(diskette drive) failure
3. System board
001-274-XXX 1. Device on IRQ7
System IRQ7 failure
2. System board
001-275-XXX 1. Device on IRQ8
System IRQ8 failure
2. System board
001-276-XXX 1. Device on IRQ9
System IRQ9 failure
2. System board
001-277-XXX 1. Device on IRQ10
System IRQ10 failure
2. System board
001-278-XXX 1. Device on IRQ11
System IRQ11 failure
2. System board
001-279-XXX 1. Device on IRQ12
System IRQ12 failure
2. System board
001-280-XXX 1. Device on IRQ13
System IRQ13 failure
2. System board
001-281-XXX 1. Hard disk drive cable
System IRQ14
2. Hard disk drive
(hard disk drive) failure
3. System board
001-282-XXX 1. Device on IRQ15
System IRQ15 failure
2. System board

Chapter 7. Symptom-to-FRU Index 59

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
001-286-XXX System board
001-287-XXX
001-288-XXX
System Timer failure
001-292-XXX 1. Run Setup and re-test
System CMOS
2. System board
RAM error
001-293-XXX 1. CMOS Battery
System CMOS Battery
2. System board
001-298-XXX 1. Flash the system. See “Flash update
System RTC date/time update failure procedures” on page 207
2. System board
001-299-XXX System board
System RTC periodic interrupt failure
001-300-XXX System board
System RTC Alarm failure
001-301-XXX 1. Flash the system. See “Flash update
System RTC Century byte error procedures” on page 207
2. System board
005-000-XXX No action
Video Test Passed
005-00X-XXX 1. Video card, if installed
Video error
2. System board
005-010-XXX 1. Video card, if installed
005-011-XXX
2. System board
005-012-XXX
005-013-XXX
Video Signal failure
005-016-XXX 1. Video Ram
Video Simple Pattern
2. Video card, if installed
test failure
3. System board
005-024-XXX 1. Video card, if installed
Video Addressing test failure
2. System board
005-025-XXX 1. Video card, if installed
Video Checksum Value error
2. System board
005-027-XXX 1. Run Setup
Video Configuration/Setup error
2. Video drivers update
3. Video card, if installed
4. System board
005-031-XXX 1. Video cable
Video Device Cable failure
2. Monitor
3. Video card, if installed
4. System board
005-032-XXX 1. Video card, if installed
Video Device Controller failure
2. System board

60 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
005-036-XXX 1. Video card, if installed
Video Register error
2. System board
005-038-XXX 1. Video card, if installed
System BIOS extension failure
2. System board
005-040-XXX 1. Video card, if installed
Video IRQ failure
2. System board
005-195-XXX Information only
Video Test aborted by user Re-start the test, if necessary
005-196-XXX 1. Press F3 to review the log file
Video test halt, error threshold exceeded
2. Re-start the test to reset the log file
005-197-XXX 1. Make sure the component that is called
Video test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component called out in
warning statement
4. Replace the component under test
005-198-XXX 1. If a component is called out, make sure
Video test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
005-199-XXX 1. Go to “Undetermined problems” on page
Video test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
005-2XX-XXX 1. Video card, if installed
005-3XX-XXX
2. System board
Video subsystem error
006-000-XXX No action
Diskette interface Test Passed
006-0XX-XXX 1. Diskette drive Cable
Diskette interface error
2. Diskette drive
3. System board
006-195-XXX Information only
Diskette interface Test aborted by user Re-start the test, if necessary
006-196-XXX 1. Press F3 to review the log file
Diskette interface test halt, error threshold
2. Re-start the test to reset the log file
exceeded

Chapter 7. Symptom-to-FRU Index 61

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
006-197-XXX 1. If a component is called out, make sure
Diskette interface test warning it is connected and/or enabled
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
006-198-XXX 1. If a component is called out, make sure
Diskette interface test aborted it is connected and/or enabled
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
006-199-XXX 1. Go to “Undetermined problems” on page
Diskette interface test failed, cause unknown 81
2. Flash the system and re-test
3. Replace component under function test
006-25X-XXX 1. Diskette drive cable
Diskette interface Error
2. Diskette drive
3. System board
011-000-XXX No action
Serial port Interface Test Passed
011-001-XXX 1. Remove external serial device, if
Serial port Presence present
2. Run setup, enable port
3. System board
011-002-XXX System board
011-003-XXX
Serial port Timeout/Parity error
011-013-XXX System board
011-014-XXX
Serial port Control Signal/Loopback test
failure
011-015-XXX 1. Wrap plug
Serial port External Loopback failure
2. System board
011-027-XXX 1. Run Setup, enable port
Serial port Configuration/Setup error
2. Flash the system. See “Flash update
procedures” on page 207
3. System board
011-03X-XXX System board
011-04X-XXX
Serial port failure
011-195-XXX Information only
Serial port Test aborted by user Re-start the test, if necessary
011-196-XXX 1. Press F3 to review the log file
Serial port test halt, error threshold exceeded
2. Re-start the test to reset the log file

62 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
011-197-XXX 1. Make sure the component that is called
Serial port test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
011-198-XXX 1. If a component is called out, make sure
Serial port test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
011-199-XXX 1. Go to “Undetermined problems” on page
Serial port test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
011-2XX-XXX 1. External serial device
Serial port signal failure
2. System board
014-000-XXX No action
Parallel port Interface Test Passed
014-001-XXX 1. Remove external parallel device, if
Parallel port Presence present
2. Run setup, enable port
3. System board
014-002-XXX System board
014-003-XXX
Parallel port Timeout/Parity error
014-013-XXX System board
014-014-XXX
Parallel port Control Signal/Loopback test
failure
014-015-XXX 1. Wrap plug
Parallel port External Loopback failure
2. System board
014-027-XXX 1. Run Setup, enable port
Parallel port Configuration/Setup error
2. Flash the system. See “Flash update
procedures” on page 207
3. System board
014-03X-XXX System board
014-04X-XXX
Parallel port failure
014-195-XXX Information only
Parallel port Test aborted by user Re-start the test, if necessary

Chapter 7. Symptom-to-FRU Index 63

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
014-196-XXX 1. Press F3 to review the log file
Parallel port test halt, error threshold
2. Re-start the test to reset the log file
exceeded
014-197-XXX 1. Make sure the component that is called
Parallel port test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
014-198-XXX 1. If a component is called out, make sure
Parallel port test aborted it is connected and/or enabled
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
014-199-XXX 1. Go to “Undetermined problems” on page
Parallel port test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
014-2XX-XXX 1. External parallel device
014-3XX-XXX
2. System board
Parallel port failure
015-000-XXX No action
USB port Interface Test Passed
015-001-XXX 1. Remove USB device(s) and re-test
USB port Presence
2. System board
015-002-XXX 1. Remove USB device(s) and re-test
USB port Timeout
2. System board
015-015-XXX 1. Remove USB device(s) and re-test
USB port External Loopback failure
2. System board
015-027-XXX 1. Flash the system. See “Flash update
USB port Configuration/Setup error procedures” on page 207
2. System board
015-032-XXX System board
USB port Device Controller failure
015-034-XXX 1. Reboot the system
USB port buffer
2. Flash the system and re-test. See “Flash
allocation failure
update procedures” on page 207
3. Run memory test
4. System board
015-035-XXX 1. Remove USB device(s) and re-test
USB port Reset condition detected
2. System board

64 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
015-036-XXX System board
USB port Register error
015-040-XXX 1. Run setup and check for conflicts
USB port IRQ failure
2. Flash the system. See “Flash update
procedures” on page 207
3. System board
015-195-XXX Information only
USB port Test aborted by user Re-start the test, if necessary
015-196-XXX 1. Press F3 to review the log file
USB port test halt, error threshold exceeded
2. Re-start the test to reset the log file
015-197-XXX 1. Make sure the component that is called
USB port test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
015-198-XXX 1. If a component is called out, make sure
USB port test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
015-199-XXX 1. Go to “Undetermined problems” on page
USB port test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
018-000-XXX No action
PCI Card Test Passed
018-0XX-XXX 1. Riser card, if installed
PCI Card Failure
2. System board
018-195-XXX 1. PCI card
PCI Card Test aborted by user
2. Information only
Re-start the test, if necessary
018-196-XXX 1. Press F3 to review the log file
PCI Card test halt, error threshold exceeded
2. Re-start the test to reset the log file

Chapter 7. Symptom-to-FRU Index 65

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
018-197-XXX 1. Make sure the component that is called
PCI Card test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
018-198-XXX 1. If a component is called out, make sure
PCI Card test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
018-199-XXX 1. Go to “Undetermined problems” on page
PCI Card test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
018-250-XXX 1. PCI card
PCI Card Services error
2. Riser card, if installed
3. System board
020-000-XXX No action
PCI Interface Test Passed
020-0XX-XXX 1. PCI card
PCI Interface error
2. Riser card, if installed
3. System board
020-195-XXX Information only
PCI Test aborted by user Re-start the test, if necessary
020-196-XXX 1. Press F3 to review the log file
PCI test halt, error threshold exceeded
2. Re-start the test to reset the log file
020-197-XXX 1. Make sure the component that is called
PCI test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test

66 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
020-198-XXX 1. If a component is called out, make sure
PCI test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
020-199-XXX 1. Go to “Undetermined problems” on page
PCI test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
020-262-XXX 1. PCI card
PCI system error
2. Riser card, if installed
3. System board
025-000-XXX No action
IDE interface Test Passed
025-00X-XXX 1. IDE signal cable
025-01X-XXX
2. Check power supply voltages
IDE interface failure
3. Reseat IDE signal cable
4. IDE device
5. System board
025-027-XXX 1. IDE signal cable
IDE interface Configuration/Setup error
2. Flash the system. See “Flash update
procedures” on page 207
3. Reseat IDE signal cable
4. IDE device
5. System board
025-02X-XXX 1. IDE signal cable
025-03X-XXX
2. Check power supply
025-04X-XXX
IDE Interface failure 3. Reseat IDE signal cable
4. IDE device
5. System board
025-195-XXX Information only
IDE interface Test aborted by user Re-start the test, if necessary
025-196-XXX 1. Press F3 to review the log file
IDE interface test halt, error threshold
2. Re-start the test to reset the log file
exceeded
025-197-XXX 1. Make sure the component that is called
IDE interface test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test

Chapter 7. Symptom-to-FRU Index 67

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
025-198-XXX 1. If a component is called out, make sure
IDE interface test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
025-199-XXX 1. Go to “Undetermined problems” on page
IDE interface test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
030-000-XXX No action
SCSI interface Test Passed
030-00X-XXX 1. SCSI signal cable
030-01X-XXX
2. Check power supply
SCSI interface failure
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-027-XXX 1. SCSI signal cable
SCSI interface Configuration/Setup error
2. Flash the system. See “Flash update
procedures” on page 207
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-03X-XXX 1. SCSI signal cable
030-04X-XXX
2. Check power supply
SCSI interface error
3. SCSI device
4. SCSI adapter card, if installed
5. System board
030-195-XXX Information only
SCSI interface Test aborted by user Re-start the test, if necessary
030-196-XXX 1. Press F3 to review the log file
SCSI interface test halt, error threshold
2. Re-start the test to reset the log file
exceeded
030-197-XXX 1. Make sure the component that is called
SCSI interface test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test

68 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
030-198-XXX 1. If a component is called out, make sure
SCSI interface test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
030-199-XXX 1. Go to “Undetermined problems” on page
SCSI interface test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
035-000-XXX No action
RAID interface Test Passed
035-0XX-XXX 1. RAID signal cable
RAID interface Failure
2. RAID device
3. RAID adapter card, if installed
4. System board
035-195-XXX Information only
RAID interface Test aborted by user Re-start the test, if necessary
035-196-XXX 1. Press F3 to review the log file
RAID interface test halt, error threshold
2. Re-start the test to reset the log file
exceeded
035-197-XXX 1. Make sure the component that is called
RAID interface test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
035-198-XXX 1. If a component is called out, make sure
RAID interface test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
035-199-XXX 1. See “Undetermined problems” on page
RAID interface test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
071-000-XXX No action
Audio port Interface Test Passed

Chapter 7. Symptom-to-FRU Index 69

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
071-00X-XXX 1. Run Setup
071-01X-XXX
2. Flash the system. See “Flash update
071-02X-XXX
procedures” on page 207
Audio port error
3. System board
071-03X-XXX 1. Speakers
Audio port failure
2. Microphone
3. Audio card, if installed
4. System board
071-04X-XXX 1. Run Setup
Audio port failure
2. Audio card, if installed
3. System board
071-195-XXX Information only
Audio port Test aborted by user Re-start the test, if necessary
071-196-XXX 1. Press F3 to review the log file
Audio port test halt, error threshold
2. Re-start the test to reset the log file
exceeded
071-197-XXX 1. Make sure the component that is called
Audio port test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
071-198-XXX 1. If a component is called out, make sure
Audio port test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
071-199-XXX 1. See “Undetermined problems” on page
Audio port test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
071-25X-XXX 1. Speakers
Audio port failure
2. Audio card, if installed
3. System board
080-000-XXX No action
Game Port interface Test Passed
080-XXX-XXX 1. Remove the game port device and
Game Port interface Error re-test the system
080-195-XXX Information only
Game Port interface Test aborted by user Re-start the test, if necessary

70 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
080-196-XXX 1. Press F3 to review the log file
Game Port interface test halt, error threshold
2. Re-start the test to reset the log file
exceeded
080-197-XXX 1. Make sure the component that is called
Game Port interface test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
080-198-XXX 1. If a component is called out, make sure
Game Port interface test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
080-199-XXX 1. See “Undetermined problems” on page
Game Port interface test failed, cause 81
unknown
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
086-000-XXX No action
Mouse Port interface Test Passed
086-001-XXX 1. Mouse
Mouse Port interface Presence
2. System board
086-032-XXX 1. Mouse
Mouse Port interface Device controller
2. System board
failure
086-035-XXX 1. Mouse
Mouse Port interface Reset
2. System board
086-040-XXX 1. Run Setup
Mouse Port interface IRQ failure
2. Mouse
3. System board
086-195-XXX Information only
Mouse Port interface Test aborted by user Re-start the test, if necessary
086-196-XXX 1. Press F3 to review the log file
Mouse Port interface test halt, error
2. Re-start the test to reset the log file
threshold exceeded

Chapter 7. Symptom-to-FRU Index 71

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
086-197-XXX 1. Make sure the component that is called
Mouse Port interface test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
086-198-XXX 1. If a component is called out, make sure
Mouse Port interface test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
086-199-XXX 1. See “Undetermined problems” on page
Mouse Port interface test failed, cause 81
unknown
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
089-000-XXX No action
Microprocessor Test Passed
089-XXX-XXX 1. Microprocessor(s)
Microprocessor failure
2. System board
089-195-XXX Information only
Microprocessor Test aborted by user Re-start the test, if necessary
089-196-XXX 1. Press F3 to review the log file
Microprocessor test halt, error threshold
2. Re-start the test to reset the log file
exceeded
089-197-XXX 1. Make sure the component that is called
Microprocessor test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
089-198-XXX 1. Flash the system. See “Flash update
Microprocessor test aborted procedures” on page 207
2. Go to “Undetermined problems” on page
81
089-199-XXX 1. See “Undetermined problems” on page
Microprocessor test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
170-000-XXX No action
Voltage Sensor(s) Test Passed

72 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
170-0XX-XXX 1. Flash system
Voltage Sensor(s) failure
2. System board
170-195-XXX Information only
Voltage Sensor(s) Test aborted by user Re-start the test, if necessary
170-196-XXX 1. Press F3 to review the log file
Voltage Sensor(s) test halt, error threshold
2. Re-start the test to reset the log file
exceeded
170-197-XXX 1. Make sure the component that is called
Voltage Sensor(s) test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
170-198-XXX 1. If a component is called out, make sure
Voltage Sensor(s) test aborted it is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
170-199-XXX 1. See “Undetermined problems” on page
Voltage Sensor(s) test failed, cause unknown 81
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
170-250-XXX 1. Power supply
170-251-XXX
2. System board
Voltage Sensor(s) Voltage limit error
170-254-XXX 1. Voltage Regulator Module (VRM)
Voltage Sensor(s) Voltage Regulator Module
2. Microprocessor
error
3. System board
175-000-XXX No action
Thermal Sensor(s) Test Passed
175-0XX-XXX 1. Flash system
Thermal Sensor(s) failure
2. System board
175-195-XXX Information only
Thermal Sensor(s) Test aborted by user Re-start the test, if necessary
175-196-XXX 1. Press F3 to review the log file
Thermal Sensor(s) test halt, error threshold
2. Re-start the test to reset the log file
exceeded

Chapter 7. Symptom-to-FRU Index 73

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
175-197-XXX 1. Make sure the component that is called
Thermal Sensor(s) test warning out is connected and/or enabled. See
Chapter 6, “Using the Setup Utility,” on
page 51
2. Re-run test
3. Replace the component that is called out
in warning statement
4. Replace the component under test
175-198-XXX 1. If a component is called out, make sure
Thermal Sensor(s) test aborted it is connected and/or enabled
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Go to “Undetermined problems” on page
81
175-199-XXX 1. See “Undetermined problems” on page
Thermal Sensor(s) test failed, cause 81
unknown
2. Flash the system and re-test. See “Flash
update procedures” on page 207
3. Replace component under function test
175-250-XXX 1. Check fans
175-251-XXX
2. Check Power supply voltages
Thermal Sensor(s) limit error
3. Microprocessor
4. System board
185-000-XXX No action
Asset Security Test Passed
185-XXX-XXX 1. Flash system
Asset Security failure
2. System board
185-278-XXX 1. Assure Asset Security Enabled
Asset Security Chassis Intrusion
2. C2 Cover Switch
3. System board
201-000-XXX No action
System Memory Test Passed
201-XXX-XXX 1. Replace the memory module called out
System Memory error by the test
2. System board
202-000-XXX No action
System Cache Test Passed
202-XXX-XXX 1. Cache, if removable
System Cache error
2. System board
3. Microprocessor
206-000-XXX No action
Diskette Drive Test Passed
206-XXX-XXX 1. Diskette Drive Cable
Diskette Drive error
2. Check power supply voltages
3. Diskette drive
4. System board

74 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
215-000-XXX No action
CD-ROM Drive Test Passed
215-XXX-XXX 1. CD-ROM Drive Cable
CD-ROM Drive error
2. Check power supply voltages
3. CD-ROM drive
4. System board
217-000-XXX No action
Hard Disk Drive Test Passed
217-25X-XXX 1. Hard Disk Drive Cable
217-26X-XXX
2. Check power supply voltages
Hard Disk Drive (IDE) error
3. Reseat the hard disk drive cable
4. Hard Disk drive (IDE)
5. System board
217-28X-XXX 1. Hard Disk Drive Cable
217-29X-XXX
2. Check power supply voltages
Hard Disk Drive (SCSI) error
3. Reseat the hard disk drive cable
4. Hard Disk drive (SCSI)
5. SCSI adapter card
6. System board
220-000-XXX No action
Hi-Capacity Cartridge Drive Test Passed
220-XXX-XXX 1. Remove the Hi-Capacity Cartridge
Hi-Capacity Cartridge Drive error Drive and re-test the system
301-XXX-XXX 1. Keyboard
Keyboard error
2. Check and test mouse
3. System board
301-000-XXX No action
Keyboard Test Passed
302-000-XXX No action
Mouse Test Passed
302-XXX-XXX 1. Mouse
Mouse error
2. Check and test Keyboard
3. System board
303-000-XXX No action
Joystick Test Passed
303-XXX-XXX Remove the Joystick and re-test the system
Joystick error
305-000-XXX No action
Monitor DDC Test Passed
305-250-XXX 1. Run Setup to enable DDC
Monitor DDC self test failure
2. Cable
3. Monitor
4. Video card
5. System board

Chapter 7. Symptom-to-FRU Index 75

Downloaded from www.Manualslib.com manuals search engine

 Diagnostic Error Code FRU/Action
415-000-XXX No action
Modem Test Passed
415-XXX-XXX Remove the Modem and re-test the system
Modem error

76 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Beep symptoms
Beep symptoms are tones or a series of tones separated by pauses (intervals
without sound) during POST.

The following table describes beep symptoms.

Beep Symptom FRU/Action

2 short beeps Perform the following actions in order.
CMOS setting error 1. Start the Setup Utility program and press
F10 to Save and exit. See Chapter 6,
“Using the Setup Utility,” on page 51.
2. Start the Setup Utility program and press
F7 to load defaults and then press F10 to
Save and exit.
3. Perform a Boot block recovery. See
“Recovering from a POST/BIOS update
failure” on page 208.
1 long and 2 short beeps Perform the following actions in order.
Monitor or video adapter card error 1. Make sure the monitor is properly
connected to the computer.
2. Replace the video adapter card (if
present).
3. Replace the system board.
1 long and 3 short beeps Perform the following actions in order.
Keyboard error 1. Make sure the keyboard is properly
connected to the keyboard connector.
2. Replace the keyboard.
3. Replace the system board.
1 long and 9 short beeps BIOS ROM error Perform the following actions in order.
1. Start the Setup Utility program and press
F7 to load defaults and then press F10 to
Save and exit. See Chapter 6, “Using the
Setup Utility,” on page 51.
2. Perform a Boot block recovery. See
“Recovering from a POST/BIOS update
failure” on page 208.
3. Replace the system board.
Continuos long beeps Perform the following actions in order.
DRAM memory error 1. Make sure the memory module(s) are
properly seated in the connector(s).
2. Replace the memory module(s).
3. Replace the system board.

Chapter 7. Symptom-to-FRU Index 77

Downloaded from www.Manualslib.com manuals search engine

 POST error codes
Each time you power-on the system, it performs a series of tests that check the
operation of the system and some options. This series of tests is called the
Power-On Self-Test, or POST. POST does the following operations.
v Checks some basic system-board operations
v Checks the memory operation
v Starts the video operation
v Verifies that the boot drive is working

If the POST detects a problem, an error message appears on the screen. A single
problem can cause several error messages to appear. When you correct the cause of
the first error message, the other error messages probably will not appear on the
screen the next time you turn on the system.

POST Error Message Description/Action

CMOS battery failed The CMOS battery is no longer functional.

Replace the battery.

CMOS checksum error - defaults loaded Checksum of CMOS is incorrect.

The computer loads the default

configuration settings. This error might
indicate that CMOS has become corrupt due
to a weak CMOS battery.
CPU at nnnn nnnn is the running speed of the
microprocessor.
Press Esc to skip memory test Pressing Esc skips the full memory test
HARD DISK INSTALL FAILURE Cannot find or initialize the hard disk drive
controller or the drive.

Make sure the hard disk drive is correctly

installed.

If no hard disk drives are installed, make

sure the hard disk drive selection in Setup is
set to NONE.
Keyboard error or no keyboard present Cannot initialize the keyboard.

Make sure the keyboard is properly

connected to the computer and that no keys
are held pressed during POST.

To purposely configure the computer

without a keyboard, set the error halt
condition in Setup to HALT ON ALL, BUT
KEYBOARD. The BIOS then ignores the
missing keyboard during POST.
Memory Test: This message displays during a full memory
test, counting down the memory areas being
tested.
Memory test fail If POST detects an error during memory
testing, additional information appears. This
information gives specifics about the type
and location of the memory error.

78 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 POST Error Message Description/Action
Press TAB to show POST screen Pressing the TAB key permits the user to
toggle between the default POST display
screen and a custom POST display screen.
Error: Non-System disk or disk error The BIOS was unable to find a suitable boot
Replace and press any key when ready device.

Make sure the boot drive is properly

connected to the computer.

Make sure you have bootable media.

Chapter 7. Symptom-to-FRU Index 79

Downloaded from www.Manualslib.com manuals search engine

 Miscellaneous error messages
Message/Symptom FRU/Action
Changing display colors Display/Monitor
Computer will not power-off. See “Power 1. Power Switch
Supply Problems” on page 55.
2. System Board
3. Riser card, if installed
Computer will not RPL from server 1. Ensure that network is in startup
sequence as first device or first device
after diskette
2. Ensure that network adapter is enabled
for RPL
3. Network adapter (Advise network
administrator of new MAC address)
Computer will not perform a Wake On 1. Check power supply and signal cable
LAN® (if applicable) connections to network adapter
2. Ensure that the operating system settings
are set to enable Wake on LAN®
3. Ensure Wake On LAN feature is enabled
in Setup/Configuration (see “Starting the
Setup Utility program” on page 51)
4. Ensure network administrator is using
correct MAC address
5. Ensure no interrupt or I/O address
conflicts
6. Network adapter (advise network
administrator of new MAC address)
Dead computer. See “Power Supply 1. Power Supply
Problems” on page 55.
2. System Board
Diskette drive in-use light remains on or 1. Diskette Drive
does not light when drive is active.
2. System Board
3. Diskette Drive Cable
Flashing cursor with an otherwise blank 1. System Board
display.
2. Primary Hard Disk Drive
3. Hard Disk Drive Cable
Incorrect memory size during POST 1. Run the Memory tests
2. Memory Module
3. System Board
″Insert a Diskette″ icon appears with a 1. System Board
known-good diagnostics diskette in the first
2. Diskette Drive Cable
3.5-inch diskette drive.
3. Network Adapter
Intensity or color varies from left to right of 1. Display
characters and color bars
2. Video adapter (if present)
3. System Board
No power or fan not running 1. See “Power Supply Problems” on page
55.

80 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Message/Symptom FRU/Action
Non-system disk or disk error-type message 1. Diskette Drive
with a known-good diagnostic diskette.
2. System Board
3. Diskette Drive Cable
Other display symptoms not listed above 1. Display
(including blank or illegible display)
2. System Board
Power-on indicator or hard disk drive in-use 1. Power switch/LED assembly
light not on, but computer works correctly
2. System Board
Printer problems 1. Printer
2. System Board
Program loads from the hard disk with a 1. Run Setup and check Startup sequence.
known-good diagnostics diskette in the first
2. Diskette Drive
3.5-inch diskette drive
3. Diskette Drive Cable
4. System Board
5. Power Supply
RPL computer cannot access programs from 1. If network administrator is using
its own hard disk. LCCM Hybrid RPL, check startup
sequence:
a. First device - network
b. Second device - hard disk
2. Hard disk drive
RPL computer does not RPL from server 1. Check startup sequence
2. Check the network adapter LED status
Serial or parallel port device failure (system 1. External Device Self-Test OK?
board port)
2. External Device
3. Cable
4. System Board
Serial or parallel port device failure (adapter 1. External Device Self-Test OK?
port)
2. External Device
3. Cable
4. Alternate Adapter
5. System Board
Some or all keys on the keyboard do not 1. Keyboard
work
2. Keyboard Cable
3. System Board

Undetermined problems
If this computer has a parallel ATA hard disk drive, make sure that the hard disk
drive is jumpered as a master and the optical drive is jumpered as a slave.
1. Power-off the computer.
2. Remove or disconnect the following components (if installed) one at a time.
a. External devices (modem, printer, or mouse)
b. Any adapters

Chapter 7. Symptom-to-FRU Index 81

Downloaded from www.Manualslib.com manuals search engine

 c. Memory modules
d. Extended video memory
e. External Cache
f. External Cache RAM
g. Hard disk drive
h. Diskette drive
3. Power-on the computer to re-test the system.
4. Repeat steps 1 through 3 until you find the failing device or adapter.

If all devices and adapters have been removed, and the problem continues, replace
the system board.

82 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393,
7394, and 7395)
Important
Before you replace any FRU, read Chapter 2, “Safety information,” on page 3.
These precautions and guidelines will help you work safely.

FRU replacements are to be done by trained service technicians only.

This chapter does not contain a remove and replace procedure for all FRUs. Only
the major FRUs are documented.

Note: The computer might look slightly different than the illustrations in this
chapter.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 83

Downloaded from www.Manualslib.com manuals search engine

 Rear connectors
The following illustration shows the locations of the connectors on the rear of the
computer.

1 Power connector
9 Ethernet connector

2 Voltage selection switch
10 USB connectors
(some models)

3 Mouse connector
11 Microphone connector

4 Keyboard connector
12 Audio line out connector

5 Serial connector
13 Audio line in connector

6 Parallel connector
14 PCI Express x1 or PCI Express x16 adapter
connector (some models)

7 VGA monitor connector
15 PCI Express x1 or PCI Express x16 adapter
connector (some models)

8 USB connectors
16 PCI adapter connectors

Removing the covers

Important
Read Chapter 2, “Safety information,” on page 3 and “Handling electrostatic
discharge-sensitive devices” on page 6 before opening the cover.

Some FRU replacements require the removal of only the left-side cover. Others
require removal of both the left-side and the right-side covers.
1. Shut down the operating system, remove any media (DVDs, CDs, or tapes)
from the drives, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.

84 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer.
4. Remove the two thumb screws at the rear of the left-side cover and slide the
cover to the rear to remove.

5. If necessary, remove the right-side cover in the same manner.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 85

Downloaded from www.Manualslib.com manuals search engine

 Locations
The following illustration will help you locate the major FRUs in the computer.

1 Heat sink and fan
6 Front panel card

2 Microprocessor
7 Hard disk drive

3 Memory modules
8 System board

4 Optical drive
9 System fan

5 Diskette drive
10 Power supply

86 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Identifying parts on the system board
There are different system boards depending on the machine type.

Machine Types 7387, 7388, and 7389

1 Microprocessor fan
11 Front panel (power switch/LED) connector

connector

2 Microprocessor and heat
12 SATA IDE connectors (2)
sink

3 Memory connector 1
13 Front USB connectors (2)

4 Memory connector 2
14 Serial (COM2 connector)

5 Clear CMOS/Recovery
15 PCI adapter connectors
jumper

6 Power supply connector
16 Front audio connector

7 Diskette drive connector
17 PCI Express x16 graphics adapter connector

8 IDE connector 1
18 PCI Express x1 graphics adapter connector

9 IDE connector 2
19 System fan connector

10 CMOS battery
20 12V power connector

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 87

Downloaded from www.Manualslib.com manuals search engine

 Machine Types 7393, 7394, and 7395

1 Microprocessor and heat
11 Front USB connectors (2)

sink

2 Microprocessor fan
12 Serial (COM2) connector
connector

3 Memory connector 1
13 Front audio connectors

4 Memory connector 2
14 PCI adapter connectors (2)

5 Power connector
15 PCI Express x1 graphics adapter connector

6 Diskette drive connector
16 CMOS battery

7 IDE connector
17 PCI Express x16 graphics adapter connector

8 SATA IDE connectors (2)
18 System fan connector

9 Front panel (power
19 12V power connector
switch/LED) connector

10 Clear CMOS/Recovery
jumper

88 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Removing and replacing the front bezel
The front bezel must be removed to replace some FRUs.
1. Remove both the left-side and right-side covers. See “Removing the covers” on
page 84.
2. Disconnect the cable for the power switch/LED assembly from the system
board. See “Identifying parts on the system board” on page 87 for the
connector location.
3. Remove the screws that secure the bezel. There are two on each side.

4. There are three plastic tabs on each side of the bezel. While applying pressure
on the top of the bezel, release each tab starting with the tabs at the top.

Note: The power switch/LED assembly cable is connected inside the bezel. Be
careful to not damage the cable and connectors when removing the bezel
from the chassis.
5. When the tabs are all released, remove the bezel from the chassis.
To replace the bezel:
6. Route the power switch/LED cable through the hole in the chassis and to the
system board.
7. Align the tabs in the chassis and snap it into position. Install the two screws on
each side to secure the bezel.
8. Reconnect the power switch/LED cable to the system board.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 89

Downloaded from www.Manualslib.com manuals search engine

 Replacing a memory module
1. Remove the left-side cover. See “Removing the covers” on page 84.
2. Locate the memory connectors. See “Identifying parts on the system board” on
page 87.
3. Open the retaining clips and remove the failing memory module.

4. Make sure the notch
1 on the new memory module is aligned correctly with
the connector key
2 on the socket. Insert the memory module straight down
into the connector until it snaps into position and the retaining clips are closed.

5. Go to “Completing the FRU replacement” on page 112.

90 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing a PCI adapter
1. Remove the left-side cover. See “Removing the covers” on page 84.
2. Remove the screw securing the adapter being replaced.
3. Pull the adapter straight out of the PCI connector.
4. Remove the new adapter from its static-protective package.
5. Install the new adapter into the appropriate PCI connector.

6. Install the screw to secure the new adapter.

7. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 91

Downloaded from www.Manualslib.com manuals search engine

 Replacing the CMOS battery
If the CMOS battery fails, the date, time, and configuration information (including
passwords) are lost. An error message is displayed when you turn on the
computer.
1. Refer to “Safety notices (multi-lingual translations)” on page 7 for information
about replacing and disposing of the battery.
2. Turn off the computer and all attached devices.
3. Remove the left-side cover. See “Removing the covers” on page 84.
4. Locate the battery. See “Identifying parts on the system board” on page 87.
5. If necessary, remove any adapters that impede access to the battery. See
“Replacing a PCI adapter” on page 91 for more information.
6. Remove the old battery.

7. Install the new battery.

8. Replace any adapters that were removed to gain access to the battery. See
“Replacing a PCI adapter” on page 91 for instructions for replacing adapters.

Note: When the computer is turned on for the first time after battery
replacement, an error message might be displayed. This is normal after
replacing the battery.
9. Go to “Completing the FRU replacement” on page 112.

92 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the power supply
Attention
Never remove the cover on a power supply or any part that has the
following label attached.

Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no servicable parts inside
these components.

1. Remove the left-side cover. See “Removing the covers” on page 84.
2. Disconnect all power supply cables from the drives.
3. Disconnect all power supply cables from the system board. See “Identifying
parts on the system board” on page 87.
4. At the rear of the chassis, remove the four screws that secure the power supply.

5. Lift the power supply out of the chassis.

6. Install the new power supply and insert the four screws that hold the power
supply in place.
7. Reconnect all power supply cables to the system board and the drives. See
“Identifying parts on the system board” on page 87. Make sure the cables are
correctly routed.
8. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 93

Downloaded from www.Manualslib.com manuals search engine

 Replacing the system board (Types 7393, 7394, and 7395)
Note: When replacing the system board a new retention module for the
microprocessor heat sink is required. Make sure you have a new retention
module before beginning this procedure.
1. Remove both side covers. See “Removing the covers” on page 84.
2. Lay the computer on the right side to make the system board accessible.
3. Remove any adapter cards installed in the PCI connectors. See “Replacing a
PCI adapter” on page 91.
4. Carefully take note of the location of all cable connections on the system
board and disconnect all cables. See “Identifying parts on the system board”
on page 87.
5. Remove the screws that secure the system board to the chassis.
6. Lift the system board out of the chassis.
7. Remove the memory modules from the failing system board and install them
in the same location on the new system board.
8. Remove the four screws
1 securing the heat sink and fan assembly to the
system board.

9. Lift the heat sink and fan assembly off the failing system board. Lay the heat
sink on its side so that the thermal grease does not come in contact with
anything.

94 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 10. Lift the small handle
3 and open the retainer
1.

11. Lift the microprocessor
2 straight up and out of the system board socket.

Notes:
a. Your microprocessor and socket might look different than the one
illustrated.
b. Note the orientation of the notches on the microprocessor. This is
important when reinstalling the microprocessor on the new system board.
This is important when reinstalling the microprocessor on the new system
board.
c. Do not drop anything onto the microprocessor socket while it is exposed.
The socket pins must be kept as clean as possible.
12. On the new system board, release the lever securing the microprocessor
retainer and then pivot the retainer until it is fully open.

Note: There will be a black plastic cover on the microprocessor retainer to

protect the socket on the new system board. Remove the black plastic

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 95

Downloaded from www.Manualslib.com manuals search engine

 cover and place it on the microprocessor socket of the failing system
board when you complete this procedure.
13. Holding the microprocessor with your fingers, position the microprocessor so
that the notches on the microprocessor are aligned with the tabs in the
microprocessor socket on the new system board.

Important
To avoid damaging the microprocessor contacts, do not tilt the
microprocessor when installing it into the socket.

14. Lower the microprocessor straight down into the system board socket of the
new system board.

15. Lower the microprocessor retainer.

16. Lock the retainer with the small handle to secure the microprocessor in the
socket.
17. The new retention bracket has plastic one-way rings on the posts that insert
into the rear of the new system board. Install the new retention bracket by
aligning the posts on the module with the holes in the system board and
pushing the posts through the holes until the retention bracket is secure.
18. Install the heat sink and fan assembly on the new system board.
19. Install the new system board into the chassis and align the screw holes with
those in the chassis. Insert and tighten the screws that secure the system
board.
20. Connect all the cables to the system board. See “Identifying parts on the
system board” on page 87.
21. Go to “Completing the FRU replacement” on page 112.

96 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the system board (Types 7387, 7388, and 7389)
1. Remove only the left-side cover. See “Removing the covers” on page 84.
2. Lay the computer on the right side to make the system board accessible.
3. Remove any adapter cards installed in the PCI connectors. See “Replacing a
PCI adapter” on page 91.
4. Carefully take note of the location of all cable connections on the system
board and disconnect all cables. See “Identifying parts on the system board”
on page 87.
5. Remove the screws that secure the system board to the chassis.
6. Lift the system board out of the chassis.
7. Remove the retention module from the rear of the failing system board.
8. Remove the memory modules from the failing system board and install them
in the same location on the new system board.
9. Rotate handle
1 to release the heat sink clamp and then disengage the
clamp from the heat sink and fan assembly.

10. Lift the heat sink and fan assembly off the failing system board. Lay the heat
sink on its side so that the thermal grease does not come in contact with
anything.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 97

Downloaded from www.Manualslib.com manuals search engine

 11. Lift the small handle
1.

12. Lift the microprocessor
2 straight up and out of the socket.

Notes:
a. Your microprocessor and socket might look different than the one
illustrated.
b. Note the orientation of the microprocessor in the socket. Look for the small
triangle on one corner of the microprocessor. This is important when
reinstalling the microprocessor on the new system board.
c. Do not drop anything onto the microprocessor socket while it is exposed.
The socket pins must be kept as clean as possible.

98 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 13. Holding the microprocessor with your fingers, position the microprocessor so
that the small triangle
1 is aligned with the corresponding triangle on the
socket.

14. Lower the microprocessor straight down into the socket.

15. Lower and latch the handle to secure the microprocessor in the socket.
16. Install the retention module that was removed from the rear of the failing
system board on the new system board.
17. Install the heat sink and fan assembly on the system board.
18. Install the new system board into the chassis and align the screw holes with
those in the chassis. Insert and tighten the screws that secure the system
board.
19. Connect all the cables to the system board. See “Identifying parts on the
system board” on page 87.
20. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 99

Downloaded from www.Manualslib.com manuals search engine

 Replacing the microprocessor (Types 7393, 7394, and 7395)
Note: A thermal grease syringe is required to complete the microprocessor
installation. Make sure the grease syringe is available before beginning the
procedure. The FRU number for the thermal grease is 91P8835.
1. Remove the left-side cover. See “Removing the covers” on page 84.
2. Lay the computer on the right side to make the system board and
microprocessor accessible.
3. Disconnect the heat sink and fan assembly cable from the system board. See
“Identifying parts on the system board” on page 87.
4. Remove the four
1 screws securing the heat sink and fan assembly to the
system board. Notice that there is a retention bracket on the back side of the
system board.

5. Lift the heat sink and fan assembly off the failing system board. Lay the heat
sink on its side so that the thermal grease does not touch anything.

100 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 6. Lift the small handle
3 and open the retainer
1.

Important
Touch only the sides of the microprocessor. Do not touch the gold
contacts on the bottom.

7. Lift the microprocessor
2 straight up and out of the socket.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 101

Downloaded from www.Manualslib.com manuals search engine

 Notes:
a. Note the orientation of the notches
1 on the microprocessor. This is
important when reinstalling the microprocessor on the new system board.

b. Do not drop anything onto the microprocessor socket while it is exposed.

The socket pins must be kept as clean as possible.
8. Holding the microprocessor with your fingers, remove the protective cover

2 that protects the gold contacts on the new microprocessor
1 .

9. Make sure that the microprocessor retainer is fully open.

10. Lower the microprocessor straight down into the socket.

11. Lock the retainer with the small handle to secure the microprocessor in the
socket.

102 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 12. Use the thermal grease syringe to place five drops of grease on the top of the
microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the
grease syringe).

13. Install the heat sink and fan assembly on the system board.
14. Connect the heat sink and fan assembly cable to the system board. See
“Identifying parts on the system board” on page 87.
15. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 103

Downloaded from www.Manualslib.com manuals search engine

 Replacing the microprocessor (Types 7387, 7388, and 7389)
1. Remove the left-side cover. See “Removing the covers” on page 84.
2. Lay the computer on the right side to make the system board and
microprocessor accessible.
3. Disconnect the heat sink and fan assembly cable from the system board. See
“Identifying parts on the system board” on page 87.
4. Rotate handle
1 to release the heat sink clamp and then disengage the
clamp from the plastic retention bracket.

5. Lift the heat sink and fan assembly off the failing system board. Lay the heat
sink on its side so that the thermal grease does not touch anything.
6. Lift the small handle
1.

104 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7. Lift the microprocessor
2 straight up and out of the socket.

Notes:
a. Your microprocessor and socket might look different than the one
illustrated.
b. Note the orientation of the microprocessor in the socket. Look for the small
triangle on one corner of the microprocessor. This is important when
reinstalling the microprocessor on the new system board.
c. Do not drop anything onto the microprocessor socket while it is exposed.
The socket pins must be kept as clean as possible.
8. Make sure that the microprocessor retainer is fully open.
9. Holding the microprocessor with your fingers, remove the protective cover

2 that protects the gold contacts on the new microprocessor
1.

10. Holding the microprocessor with your fingers, position the microprocessor so
that the triangle
1 is aligned with the corresponding triangle on the socket.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 105

Downloaded from www.Manualslib.com manuals search engine

 11. Lower the microprocessor straight down into the socket.

Note: Install the black protective cover that was removed from the new
microprocessor onto the defective microprocessor after the installation is
complete.
12. Lower the small handle to secure the microprocessor in the socket.
13. Use the thermal grease syringe to place five drops of grease on the top of the
microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the
grease syringe).

14. Install the heat sink and fan assembly on the system board.
15. Connect the heat sink and fan assembly cable to the system board. See
“Identifying parts on the system board” on page 87.
16. Go to “Completing the FRU replacement” on page 112.

106 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the primary hard disk drive
Important
When you install a new hard disk drive, you also need a set of Product
Recovery discs. The set of Product Recovery discs will enable the contents of the
hard disk to be restored to the same state as when the computer was
originally shipped from the factory. For more information on recovering
factory-installed software, refer to “Recovering software” in the User Guide.

1. Remove the left-side and right-side covers. See “Removing the covers” on page
84.
2. Disconnect the signal and power cables from the rear of the hard disk drive.
3. Remove the two screws that secure the drive on each side.

4. Slide the drive toward the rear of the chassis until it can be removed.
5. If the drive you are replacing has jumpers on the rear, make sure the jumpers
on the new drive are in the same exact position as the drive being replaced.
6. Slide the new drive into the bay until the screws holes on each side are aligned
and install two screws in each side of the drive.
7. Reconnect the signal and power cables to the rear of the hard disk drive.
8. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 107

Downloaded from www.Manualslib.com manuals search engine

 Replacing an optical drive
1. Remove the left-side and right-side covers. See “Removing the covers” on page
84.
2. Disconnect the power cable and signal cable from the optical drive.
3. Remove the two screws that secure the drive on each side.

4. Slide the drive being replaced out the front of the computer.
5. If the drive you are replacing has jumpers on the rear, make sure the jumpers
on the new drive are in the same exact position as the drive being replaced.
6. Slide the new drive into the bay until the screws holes on each side are aligned
and install two screws in each side of the drive.
7. Reconnect the power cable and signal cable to the new optical drive.
8. Go to “Completing the FRU replacement” on page 112.

108 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the diskette drive
1. Remove the left-side and right-side covers. See “Removing the covers” on page
84.
2. Disconnect the signal and power cables from the rear of the hard disk drive.

Note: You will probably have to disconnect cables that are connected to the
system board and other drives to allow the diskette drive to be removed
from inside the chassis.
3. Remove the two screws that secure the drive on each side.

4. Slide the drive toward the rear of the chassis until it can be removed.
5. Slide the new drive into the bay until the screws holes on each side are aligned
and install two screws in each side of the drive.
6. Reconnect all signal and power cables that were disconnected. See “Identifying
parts on the system board” on page 87.
7. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 109

Downloaded from www.Manualslib.com manuals search engine

 Replacing the power switch/ LED assembly
1. Disconnect the power switch/LED assembly cable from the system board. See
“Identifying parts on the system board” on page 87.
2. Remove the front bezel. See “Removing and replacing the front bezel” on page
89.
3. Remove the power switch/LED assembly by disconnecting it from the inside of
the bezel.
4. Install the new power switch/LED assembly into the bezel.
5. Route the cable for the new power switch/LED assembly through the hole in
the chassis and to the system board.
6. Reinstall the bezel. See “Removing and replacing the front bezel” on page 89.
7. Reconnect the power switch/LED cable to the system board.
8. Go to “Completing the FRU replacement” on page 112.

110 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the front panel card assembly
1. Remove the left-side and right-side covers. See “Removing the covers” on page
84.
2. Remove the front bezel. See “Removing and replacing the front bezel” on page
89.
3. Disconnect the front USB cable and the front audio cable from the system
board. See “Identifying parts on the system board” on page 87.
4. Remove the screw on the front of the chassis that secures the front panel
assembly.

5. Route the new front panel cable through the front of the chassis and Install the
screw secures the front panel assembly.
6. Reinstall the bezel. See “Removing and replacing the front bezel” on page 89.
7. Connect the front USB cable and the front audio cable to the system board. See
“Identifying parts on the system board” on page 87.
8. Go to “Completing the FRU replacement” on page 112.

Chapter 8. Replacing FRUs (Types 7387, 7388, 7389, 7393, 7394, and 7395) 111

Downloaded from www.Manualslib.com manuals search engine

 Completing the FRU replacement
After replacing FRUs, you need to install any removed parts, replace the cover, and
reconnect any cables, including telephone lines and power cords. Also, depending
on the FRU that is replaced, you might need to confirm the updated information in
the Setup Utility program.

Note: When the power cord is first plugged in, the computer might appear to turn
on for a few seconds and then turn off. This is a normal sequence to enable
the computer to initialize.
1. Ensure that all components have been reassembled correctly and that no tools
or loose screws are left inside the computer.
2. Replace the covers that were removed and secure them with the thumb screws.
3. Reconnect the external cables and power cords to the computer. See “Rear
connectors” on page 84.
4. If you have replaced the system board, you must update (flash) the BIOS. See
“Flash update procedures” on page 207.
5. Some FRU replacements require the configuration to be updated. See Chapter 6,
“Using the Setup Utility,” on page 51.

112 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396,
7397, and 7398)
Important
Before you replace any FRU, read Chapter 2, “Safety information,” on page 3.
These precautions and guidelines will help you work safely.

FRU replacements are to be done by trained service technicians only.

This chapter does not contain a remove and replace procedure for all FRUs. Only
the major FRUs are documented.

Note: The computer might look slightly different than the illustrations in this
chapter.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 113

Downloaded from www.Manualslib.com manuals search engine

 Rear connectors
The following illustration shows the locations of the connectors on the rear of the
computer.

1 Standard mouse connector
9 PCI Express x1 adapter or Express x16
graphics adapter connector (some
models)

2 Parallel connector
10 Audio line out connector

3 Ethernet connector
11 Microphone connector

4 Audio line in connector
12 USB connectors

5 Power cord connector
13 USB connectors

6 Voltage selection switch (some
14 VGA monitor connector
models)

7 PCI adapter connectors
15 Serial connector

8 PCI Express x1 adapter or Express
16 Standard keyboard connector
x16 graphics adapter connector
(some models)

Removing the cover

Important
Read Chapter 2, “Safety information,” on page 3 and “Handling electrostatic
discharge-sensitive devices” on page 6 before opening the cover.

To remove the computer cover:

1. Remove any media (diskettes, CDs, or tapes) from the drives, shut down the
operating system, and turn off all attached devices.
2. Unplug all power cords from electrical outlets.

114 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 3. Disconnect all cables attached to the computer. This includes power cords,
input/output (I/O) cables, and any other cables that are connected to the
computer.
4. Remove any locking devices such as a padlock that secure the cover.
5. Remove the two screws at the rear of the computer cover and slide the cover to
the rear.

Locations
The following illustration will help you locate the major FRUs in the computer.

1 Fan plenum, fan,
6 Diskette drive

and heat sink

2 Microprocessor
7 Front panel card

3 Optical drive
8 Memory modules

4 Power switch/LED
9 System board
assembly

5 Hard disk drive
10 Power supply

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 115

Downloaded from www.Manualslib.com manuals search engine

 Identifying parts on the system board
System board locations are different depending on the machine type.

Machine Types 7390, 7391, and 7392

1 Microprocessor fan
11 Front panel (power switch/LED) connector

connector

2 Microprocessor and heat
12 SATA IDE connectors (2)
sink

3 Memory connector 1
13 Front USB connectors (2)

4 Memory connector 2
14 Serial (COM2 connector)

5 Clear CMOS/Recovery
15 PCI adapter connectors
jumper

6 Power supply connector
16 Front audio connector

7 Diskette drive connector
17 PCI Express x16 graphics adapter connector

8 IDE connector 1
18 PCI Express x1 graphics adapter connector

9 IDE connector 2
19 System fan connector

10 CMOS battery
20 12V power connector

116 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Machine Types 7396, 7397, and 7398

1 Microprocessor and heat
11 Front USB connectors (2)

sink

2 Microprocessor fan
12 Serial (COM2) connector
connector

3 Memory connector 1
13 Front audio connectors

4 Memory connector 2
14 PCI adapter connectors (2)

5 Power connector
15 PCI Express x1 graphics adapter connector

6 Diskette drive connector
16 CMOS battery

7 IDE connector
17 PCI Express x16 graphics adapter connector

8 SATA IDE connectors (2)
18 System fan connector

9 Front panel (power
19 12V power connector
switch/LED) connector

10 Clear CMOS/Recovery
jumper

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 117

Downloaded from www.Manualslib.com manuals search engine

 Removing and replacing the drive bay assembly
You will need to remove the drive bay assembly to access some FRUs.
1. Remove the computer cover. See “Removing the cover” on page 114.
2. Remove the front bezel by releasing the three tabs and pivoting the top of the
bezel outward.

3. Remove the two screws at the front of the chassis securing the drive bay
assembly.

118 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 4. Slide the drive bay assembly forward until it stops. Disconnect the power
supply and signal cables from the drives. Pivot the rear of the drive bay
assembly upward to remove it completely from the computer.

Note: To allow easier access to the cables, lift the fan plenum off the heat sink.
See “Locations” on page 115.
5. Reverse this procedure to replace the drive bay assembly and bezel.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 119

Downloaded from www.Manualslib.com manuals search engine

 Replacing a memory module
1. Remove the cover. See “Removing the cover” on page 114.
2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Locate the memory connectors. See “Identifying parts on the system board” on
page 116.
4. Open the retaining clips and remove the failing memory module.

5. Make sure the notch
1 on the new memory module is aligned correctly with
the connector key
2 on the socket. Insert the memory module straight down
into the connector until it snaps into position and the retaining clips are closed.

6. Replace the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
7. Go to “Completing the FRU replacement” on page 144.

120 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing a PCI adapter
1. Remove the computer cover. See “Removing the cover” on page 114.
2. Remove the screw that secures the adapter retainer and remove the retainer.

3. Remove the failing adapter.

4. Remove the new adapter from its static-protective package.
5. Install the new adapter into the appropriate connector on the system board.

6. Reinstall the adapter retainer and screw that secures the retainer.
7. Go to “Completing the FRU replacement” on page 144.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 121

Downloaded from www.Manualslib.com manuals search engine

 Replacing the CMOS battery
If the CMOS battery fails, the date, time, and configuration information (including
passwords) are lost. An error message is displayed when you turn on the
computer.

Important
Refer to “Safety notices (multi-lingual translations)” on page 7 for information
about replacing and disposing of the battery.

1. Remove the cover. See “Removing the cover” on page 114.

2. Locate the battery. See “Identifying parts on the system board” on page 116.
3. Depending on the location of the CMOS battery in the computer, you might
have to remove the drive bay assembly to access the battery. If necessary, see
“Removing and replacing the drive bay assembly” on page 118.
4. If necessary, remove any adapters that impede access to the battery. See
“Replacing a PCI adapter” on page 121 for more information.
5. Remove the old battery.

6. Install the new battery.

7. Replace the drive bay assembly if it was removed. See “Removing and
replacing the drive bay assembly” on page 118.
8. Replace any adapters that were removed to gain access to the battery. See
“Replacing a PCI adapter” on page 121 for more information.

Note: When the computer is turned on for the first time after battery
replacement, an error message might be displayed. This is normal after
replacing the battery.
9. Go to “Completing the FRU replacement” on page 144.

122 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the power supply
Attention
Never remove the cover on a power supply or any part that has the
following label attached.

Hazardous voltage, current, and energy levels are present inside any
component that has this label attached. There are no servicable parts inside
these components.

1. Remove the cover. See “Removing the cover” on page 114.

2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Disconnect all power supply cables from the drives.
4. Disconnect all power supply cables from the system board. See “Identifying
parts on the system board” on page 116.
5. Remove the hard disk drive. See “Replacing the hard disk drive” on page 140.
6. The system board must be moved out of the way to remove the power supply.
Remove the screws that secure the system board to the chassis and slide the
system board away from the power supply.

Note: You do not have to remove the system board from the chassis to
remove the power supply.
7. At the rear of the chassis, remove the three screws that secure the power
supply. Also remove the screw that secures the power supply at the front.

8. Lift the power supply out of the chassis.

9. Install the new power supply and install the three screws that secure the
power supply at the rear of the chassis and install the screw that secures the
power supply at the front.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 123

Downloaded from www.Manualslib.com manuals search engine

 10. Position the system board so that the screws holes are aligned and install the
system board screws.
11. Install the hard disk drive. Make sure to route the power supply cable for the
system board underneath the hard disk drive. See “Replacing the hard disk
drive” on page 140.
12. Reconnect all other power supply cables to the system board and the drives.
See “Identifying parts on the system board” on page 116. Make sure the cables
are correctly routed.
13. Replace the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
14. Go to “Completing the FRU replacement” on page 144.

124 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the system board (Types 7396, 7397, and 7398)
Note: When replacing the system board, a new retention bracket for the
microprocessor heat sink is required. Make sure you have a new retention
bracket before beginning this procedure.
1. Remove the cover. See “Removing the cover” on page 114
2. Lift the fan duct off the heat sink fan.
3. Remove any adapter cards installed in the PCI connectors. See “Replacing a
PCI adapter” on page 121.
4. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
5. Take note of the location of all cable connections on the system board and
disconnect all cables. See “Identifying parts on the system board” on page 116.
6. Remove the hard disk drive. See “Replacing the hard disk drive” on page 140.
7. Remove the screws that secure the system board to the chassis.
8. Lift the system board out of the chassis.
9. Remove the memory modules from the failing system board and install them
in the same location on the new system board.
10. Disconnect the heat sink and fan assembly cable from the system board. See
“Identifying parts on the system board” on page 116.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 125

Downloaded from www.Manualslib.com manuals search engine

 11. Remove the four screws
1 securing the heat sink and fan assembly to the
system board.

12. Lift the heat sink and fan assembly off the failing system board. Lay the heat
sink on its side so that the thermal grease does not come in contact with
anything.
13. Lift the small handle
3 and open the retainer
1.

126 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Important
Touch only the sides of the microprocessor. Do not touch the gold
contacts on the bottom.

14. Lift the microprocessor
2 straight up and out of the socket.

Notes:
a. Note the orientation of the notches
1 on the microprocessor. This is
important when reinstalling the microprocessor on the new system board.

b. Do not drop anything onto the microprocessor socket while it is exposed.

The socket pins must be kept as clean as possible.
15. On the new system board, release the lever securing the microprocessor
retainer and then pivot the retainer until it is fully open.

Note: There will be a black plastic cover on the microprocessor retainer to

protect the socket on the new system board. Remove the black plastic
cover and place it on the microprocessor socket of the failing system
board.
16. Holding the microprocessor with your fingers, position the microprocessor so
that the notches on the microprocessor are aligned with the tabs in the
microprocessor socket.

Important
To avoid damaging the microprocessor contacts, do not tilt the
microprocessor when installing it into the socket.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 127

Downloaded from www.Manualslib.com manuals search engine

 17. Lower the microprocessor straight down into the system board socket of the
new system board.

18. Lower the microprocessor retainer.

19. Lock the retainer with the small handle to secure the microprocessor in the
socket.
20. The new retention bracket has plastic one-way rings on the posts that insert
into the rear of the new system board. Install the new retention bracket by
aligning the posts on the module with the holes in the system board and
pushing the posts through the holes until the retention bracket is secure.
21. Install the heat sink and fan assembly on the new system board.
22. Install the new system board into the chassis and align the screw holes with
those in the chassis. Insert and tighten the screws that secure the system
board.
23. Connect all cables to the system board. See “Identifying parts on the system
board” on page 116.
24. Replace the hard disk drive. See “Replacing the hard disk drive” on page 140.
25. Install the drive bay assembly and connect the power and signal cables to the
drives.
26. Reinstall any PCI adapter cards that were removed. See “Replacing a PCI
adapter” on page 121.
27. Position the fan duct on the heat sink fan.
28. Go to “Completing the FRU replacement” on page 144.

128 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the system board (Types 7390, 7391, and 7392)
1. Remove the cover. See “Removing the cover” on page 114.
2. Lift the fan duct off the heat sink fan.
3. Remove any adapter cards installed in the PCI connectors. See “Replacing a
PCI adapter” on page 121.
4. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
5. Take note of the location of all cable connections on the system board and
disconnect all cables. See “Identifying parts on the system board” on page 116.
6. Remove the hard disk drive. See “Replacing the hard disk drive” on page 140.
7. Remove the screws that secure the system board to the chassis.
8. Lift the system board out of the chassis.
9. Remove the retention module from the rear of the failing system board.
10. Remove the memory modules from the failing system board and install them
in the same location on the new system board.
11. Disconnect the heat sink and fan assembly cable from the system board. See
“Identifying parts on the system board” on page 116.
12. Rotate handle
1 to release the heat sink clamp and then disengage the
clamp from the plastic retention bracket.

13. Lift the heat sink and fan assembly off the failing system board.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 129

Downloaded from www.Manualslib.com manuals search engine

 14. Lift the small handle
1.

Important
Touch only the sides of the microprocessor. Do not touch the gold
contacts on the bottom.

15. Lift the microprocessor
2 straight up and out of the socket.

Notes:
a. Your microprocessor and socket might look different than the one
illustrated.
b. Note the orientation of the microprocessor in the socket. Look for the small
triangle on one corner of the microprocessor. This is important when
reinstalling the microprocessor on the new system board.
c. Do not drop anything onto the microprocessor socket while it is exposed.
The socket pins must be kept as clean as possible.

130 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 16. Holding the microprocessor with your fingers, position the microprocessor so
that the small triangle
1 on one corner is aligned with the corresponding
triangle on the socket.

17. Make sure that the small handle is in the raised position.
18. Lower the microprocessor straight down into the system board socket of the
new system board.

19. Lower and latch the handle to secure the microprocessor in the socket.
20. Install the retention module that was removed from the rear of the failing
system board on the new system board.
21. Install the heat sink and fan assembly on the new system board.
22. Install the new system board into the chassis and align the screw holes with
those in the chassis. Insert and tighten the screws that secure the system
board.
23. Connect all cables to the system board. See “Identifying parts on the system
board” on page 116.
24. Replace the hard disk drive. See “Replacing the hard disk drive” on page 140.
25. Install the drive bay assembly and connect the power and signal cables to the
drives.
26. Reinstall any PCI adapter cards that were removed. See “Replacing a PCI
adapter” on page 121.
27. Position the fan duct on the heat sink fan.
28. Go to “Completing the FRU replacement” on page 144.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 131

Downloaded from www.Manualslib.com manuals search engine

 Replacing the microprocessor (Types 7396, 7397, and 7398)
Note: A thermal grease syringe is required to complete the microprocessor
installation. Make sure the grease syringe is available before beginning the
procedure. The FRU number for the thermal grease is 91P8835.
1. Remove the cover. See “Removing the cover” on page 114.
2. Lay the computer on the right side to make the system board and
microprocessor accessible.
3. Disconnect the heat sink and fan assembly cable from the system board. See
“Identifying parts on the system board” on page 87.
4. Remove the four screws securing the heat sink and fan assembly to the system
board. Notice that there is a retention bracket on the back side of the system
board.

5. Lift the heat sink and fan assembly off the failing system board.

132 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 6. Lift the small handle
3 and open the retainer
1.

Important
Touch only the sides of the microprocessor. Do not touch the gold
contacts on the bottom.

7. Lift the microprocessor
2 straight up and out of the socket.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 133

Downloaded from www.Manualslib.com manuals search engine

 Notes:
a. Note the orientation of the notches
1 on the microprocessor. This is
important when reinstalling the microprocessor on the system board.

b. Do not drop anything onto the microprocessor socket while it is exposed.

The socket pins must be kept as clean as possible.
8. Make sure that the microprocessor retainer is fully open.
9. Holding the microprocessor with your fingers, remove the protective cover

2 that protects the gold contacts on the new microprocessor
1.

10. Holding the microprocessor with your fingers, position the microprocessor so
that the notches on the microprocessor are aligned with the tabs in the
microprocessor socket.

Important
To avoid damaging the microprocessor contacts, do not tilt the
microprocessor when installing it into the socket.

134 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 11. Lower the microprocessor straight down into the system board socket of the
system board.

12. Lower the microprocessor retainer.

13. Lock the retainer with the small handle to secure the microprocessor in the
socket.
14. Use the thermal grease syringe to place five drops of grease on the top of the
microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the
grease syringe).

15. Install the heat sink and fan assembly on the system board.
16. Connect the heat sink and fan assembly cable to the system board. See
“Identifying parts on the system board” on page 87.
17. Go to “Completing the FRU replacement” on page 112.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 135

Downloaded from www.Manualslib.com manuals search engine

 Replacing the microprocessor (Types 7390, 7391, and 7392)
Note: A thermal grease syringe is required to complete the microprocessor
installation. Make sure the grease syringe is available before beginning the
procedure. The FRU number for the thermal grease is 91P8835.
1. Remove the cover. See “Removing the cover” on page 114.
2. Lift the fan duct off the heat sink fan.
3. Disconnect the heat sink and fan assembly cable from the system board. See
“Identifying parts on the system board” on page 116.
4. Rotate handle
1 to release the heat sink clamp and then disengage the
clamp from the plastic retention bracket.

5. Lift the heat sink and fan assembly off the system board.

136 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 6. Lift the small handle
1.

Important
Do not touch the gold contacts on the bottom of the microprocessor. If
you must touch the microprocessor, touch only the sides.

7. Lift the microprocessor
2 straight up and out of the socket.

Notes:
a. Your microprocessor and socket might look different than the one
illustrated.
b. Note the orientation of the microprocessor in the socket. Look for the small
triangle on one corner of the microprocessor. This is important when
reinstalling the microprocessor on the system board.
c. Do not drop anything onto the microprocessor socket while it is exposed.
The socket pins must be kept as clean as possible.
8. Make sure that the small handle is in the raised position.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 137

Downloaded from www.Manualslib.com manuals search engine

 9. Holding the microprocessor with your fingers, position the microprocessor so
that the small triangle on one corner is aligned with the corresponding
triangle on the microprocessor socket.

10. Holding the microprocessor with your fingers, remove the protective cover

2 that protects the gold contacts on the new microprocessor
1.

11. Lower the microprocessor straight down into the system board socket of the
new system board.

12. Lower and latch the handle to secure the microprocessor in the socket.

138 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 13. Use the thermal grease syringe to place five drops of grease on the top of the
microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the
grease syringe).

14. Install the heat sink and fan assembly on the system board.
15. Connect the heat sink and fan assembly to the system board. See “Identifying
parts on the system board” on page 87.
16. Position the fan duct on the heat sink fan.
17. Go to “Completing the FRU replacement” on page 144.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 139

Downloaded from www.Manualslib.com manuals search engine

 Replacing the hard disk drive
1. Remove the cover.See “Removing the cover” on page 114.
2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Remove the two screws that secure the hard disk drive bracket.

4. From the front of the chassis, slide the drive bracket to the left until it is free
of the retaining clips in the bottom of the chassis. It can now be can be
removed from the chassis.
5. Disconnect the signal and power cables from the rear of the hard disk drive.
6. Remove the four screws that secure the hard disk drive to the bracket and
remove the drive from the bracket.
7. Position the new drive into the hard disk drive bracket so that the screw holes
on each side are aligned and install two screws into each side of the drive.
8. Reconnect the signal and power cables to the rear of the hard disk drive.
9. Position the hard disk drive bracket so that it engages the retaining clips in
the bottom of the chassis when you slide the bracket to the right.
10. Slide the hard disk drive bracket to the right until the screw holes are aligned
and install the screws.
11. Reinstall the drive bay assembly and connect the power and signal cables to
the drives.
12. Go to “Completing the FRU replacement” on page 144.

140 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing an optical drive
1. Remove the cover. See “Removing the cover” on page 114.
2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Remove the screws that secure the drive in the drive bay assembly.

4. Slide the drive being replaced out the front of the drive bay assembly.
5. Slide the new drive into the bay until the screws holes on each side are aligned
and install the screws that secure the drive to the drive bay assembly.
6. Reinstall the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
7. Go to “Completing the FRU replacement” on page 144.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 141

Downloaded from www.Manualslib.com manuals search engine

 Replacing the diskette drive
1. Remove the cover. See “Removing the cover” on page 114.
2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Remove the screws at the bottom of the diskette drive that secure the drive to
the drive bay assembly.

4. Slide the diskette drive out of the drive bay assembly.

5. Slide the new drive into the bay until the screws holes at the bottom of the
drive are aligned and install the screws that secure the drive to the drive bay
assembly.
6. Reinstall the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
7. Go to “Completing the FRU replacement” on page 144.

142 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Replacing the power switch/ LED assembly
1. Remove cover. See “Removing the cover” on page 114.
2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Remove the hard disk drive. See “Replacing the hard disk drive” on page 140.
4. Disconnect the power switch/LED assembly cable from the system board. See
“Identifying parts on the system board” on page 116.
5. Remove the screw that secures the power switch/LED assembly to the chassis.

6. Note the power switch/LED assembly cable routing and remove the assembly
from the chassis.
7. Route the cable for the new power switch/LED assembly through the hole in
the chassis and to the system board.
8. Install the power switch/LED assembly into the chassis and secure the
assembly with the screw.
9. Connect the power switch/LED cable to the system board.
10. Reinstall the hard disk drive. See “Replacing the hard disk drive” on page
140.
11. Reinstall the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
12. Go to “Completing the FRU replacement” on page 144.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 143

Downloaded from www.Manualslib.com manuals search engine

 Replacing the front panel card
1. Remove cover. See “Removing the cover” on page 114.
2. Remove the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
3. Disconnect the front panel assembly cables from the system board. See
“Identifying parts on the system board” on page 116.
4. Remove the screw that secures the front panel card assembly to the chassis.

5. Note the front panel assembly cable routing and remove the assembly from
the chassis.
6. Route the cable for the new front panel card assembly through the hole in the
chassis and to the system board.
7. Install the front panel card assembly into the chassis and secure it with the
screw.
8. Connect the front panel assembly cables to the system board.
9. Reinstall the drive bay assembly. See “Removing and replacing the drive bay
assembly” on page 118.
10. Go to “Completing the FRU replacement.”

Completing the FRU replacement

After replacing FRUs, you need to install any removed parts, replace the cover, and
reconnect any cables, including telephone lines and power cords. Also, depending
on the FRU that is replaced, you might need to confirm the updated information in
the Setup Utility program.

Note: When the power cord is first plugged in, the computer might appear to turn
on for a few seconds and then turn off. This is a normal sequence to enable
the computer to initialize.
1. Ensure that all components have been reassembled correctly and that no tools
or loose screws are left inside the computer.
2. Replace the cover and secure it with two screws.

144 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 3. Reconnect the external cables and power cords to the computer. See “Rear
connectors” on page 114.
4. If you have replaced the system board, you must update (flash) the BIOS. See
“Flash update procedures” on page 207.
5. Some FRU replacements require the configuration to be updated. See Chapter 6,
“Using the Setup Utility,” on page 51.

Chapter 9. Replacing FRUs (Types 7390, 7391, 7392, 7396, 7397, and 7398) 145

Downloaded from www.Manualslib.com manuals search engine

 146 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 10. FRU lists
Notes:
1. In the following tables, A CRU (Customer Replaceable Unit) is identified by
either a 1, 2, or N in the CRU Tier column. A ″1″ means that the part is a Tier 1
CRU, A ″2″ means that the part is a Tier 2 CRU, and an ″N″ means that the
part is not a CRU.
2. For some machine types, there is a column with a heading of RoHS?. This
column contains a “Y“ if the FRU is RoHS compliant or an “N“ if the FRU is
not RoHS compliant. Please read “Important information about replacing RoHS
compliant FRUs” on page 2 before replacing any FRUs.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 147

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7387

Item CRU
# 7387 FRUs FRU# Tier RoHS?
1 FRU, Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y
2 Microprocessor, 3800+ Athlon64 AM2 X2 (2.0 GHz processor, 89W) (models 41X4241 N Y
21G 21B 22U 22S 22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 25G 26U 26F
27U 27F 28G 21Q 26S 26Y 27S 27Y)
2 Microprocessor, 4200+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) (models 41X1421 N Y
41U 41F 41S 41P 41Y 42M 42A 42T 43V 44U 44F 45G 44S 44Y)
3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
21G 21B 22U 22S 22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 25G 26U 26F
27U 27F 41U 41F 41S 41P 41Y 42M 42A 42T 43V 21Q 26S 26Y 27S 27Y)
3 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 28G 41X4252 2 Y
44U 44F 45G 44S 44Y)
4 DVD-ROM 16x -48x (models 9FU 9FF 9GU 9GF) 41X3544 N Y
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21G 21B 22U 22S 41X3547 N Y
22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9JS
9JP 9JY 9KD 8HS 8HP 8HY 8JD 8KS 8KP 8KY 8SD)
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21G 21B 22U 22S 41X3548 N Y
22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9JS
9JP 9JY 9KD 8HS 8HP 8HY 8JD 8KS 8KP 8KY 8SD)
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21G 21B 22U 22S 41X3549 N Y
22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9JS
9JP 9JY 9KD 8HS 8HP 8HY 8JD 8KS 8KP 8KY 8SD)
4 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 21G 21B 22U 22S 42Y9368 N Y
22P 22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9AG
8AG 2BU 2BF 2CS 2CY 2HP 2DS 2DY 4CP 2GB 2GH 48U 48F 9HU 9HF
9JS 9JP 9JY 9KD 9PS 9PY 9QP 9SD 8DG 8ES 8EY 8FP 8GD 8HS 8HP 8HY
8JD 8NS 8NY 8PP 8QD 8KS 8KP 8KY 8SD 2JU 2JF 2NS 2NY 2RP 2SD 9BG)

148 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7387 FRUs FRU# Tier RoHS?
4 PATA Combo RoHS TS-H492C (VISTA FW) (models 21G 21B 22U 22S 22P 42Y9369 N Y
22M 23S 23P 23Y 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q 9AG 8AG
2BU 2BF 2CS 2CY 2HP 2DS 2DY 4CP 2GB 2GH 48U 48F 9HU 9HF 9JS 9JP
9JY 9KD 9PS 9PY 9QP 9SD 8DG 8ES 8EY 8FP 8GD 8HS 8HP 8HY 8JD 8NS
8NY 8PP 8QD 8KS 8KP 8KY 8SD 2JU 2JF 2NS 2NY 2RP 2SD 9BG)
4 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 25G 26U 41X3550 N Y
26F 27U 27F 28G 42M 42A 42T 43V 44U 44F 45G 26S 26Y 27S 27Y 44S 44Y
8KS 8KP 8KY 8MD 29G)
4 HLDS RoHS RAMBO-8 drive (models 25G 26U 26F 27U 27F 28G 42M 42A 42Y9371 N Y
42T 43V 44U 44F 45G 26S 26Y 27S 27Y 44S 44Y 5AP 2FV 2EM 46S 46Y 4DP
47S 47Y 4EP 49U 49F 4AU 4AF 4BA 4BT 8KS 8KP 8KY 8MD 2MU 2MF
2PS 2PY 2TP 2UD 2QS 2QY 2YP 4BQ 4FV 4FK 4GM 29G)
4 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 25G 26U 26F 27U 27F 28G 43C0144 N Y
42M 42A 42T 43V 44U 44F 45G 26S 26Y 27S 27Y 44S 44Y 5AP 2FV 2EM
46S 46Y 4DP 47S 47Y 4EP 49U 49F 4AU 4AF 4BA 4BT 8KS 8KP 8KY 8MD
2MU 2MF 2PS 2PY 2TP 2UD 2QS 2QY 2YP 4BQ 4FV 4FK 4GM 29G)
5 Diskette drive, w/bezel (models)
6 Front panel card (USB/Audio) assembly (all models) 41N5330 N Y
7 Hard disk drive, 80GB, 7200rpm, serial ATA (models 23S 23P 23Y) 40Y9034 N Y
7 Hard disk drive, 160GB, 7200rpm, serial ATA (models 21G 21B 22U 22S 40Y9035 N Y
22P 22M 24U 24F 24S 24P 24Y 41U 41F 41S 41P 41Y 21Q)
7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 25G 26U 26F 27U 40Y9036 N Y
27F 28G 42M 42A 42T 43V 44U 44F 45G 26S 26Y 27S 27Y 44S 44Y)
8 System board, nVidia C51g (models 21G 21B 22U 22S 22P 22M 23S 23P 23Y 45C3619 N Y
24U 24F 24S 24P 24Y 25G 26U 26F 27U 27F 41U 41F 41S 41P 41Y 42M 42A
42T 43V 44U 44F 21Q 26S 26Y 27S 27Y 44S 44Y 9AG 8AG 2BU 2BF 2CS
2CY 5AP 2HP 2DS 2DY 4CP 2FV 2EM 2GB 2GH 46S 46Y 4DP 47S 47Y 4EP
48U 48F 49U 49F 4AU 4AF 4BA 4BT 9FU 9FF 9GU 9GF 9HU 9HF 9JS 9JP
9JY 9KD 9MS 9MP 9MY 9PS 9PY 9SD 8DG 8ES 8EY 8FP 8GD 8HS 8HP
8HY 8JD 8KS 8KP 8KY 8MD 8NS 8NY 8PP 8QD 8RS 8RP 8RY 8SD 2JU 2JF
2MU 2MF 2NS 2NY 2RP 2SD 2PS 2PY 2TP 2UD 2QS 2QY 2YP 2ND 4BQ
4FV 4FK 4GM 9BG 9MD)
9 System Fan, rear w/grill (all models) 41N5339 N Y
10 Power supply, 280W ATX , Standard (models 21G 22U 22M 24U 24F 25G 41N3479 N Y
26U 26F 27U 27F 28G 41U 41F 42M 42A 42T 44U 44F 45G 26S 26Y 27S 27Y
44S 44Y)
10 Power supply, 280W, Robust (models 21B 22S 22P 23S 23P 23Y 24S 24P 24Y 41N3482 N Y
41S 41P 41Y 43V 21Q)

The FRUs listed in the following table are not illustrated.

CRU
7387 FRUs FRU# Tier RoHS?
Cable, SATA 250mm (all models) 41A7145 2 Y
Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 2 Y
IDE cable for Tower (2-drop) (all models) 41A7140 2 Y
Modem Phone Cable (all models) 39K5120 2 Y
Cable, diskette drive (RoHs) (all models) 41A7130 2 Y
Mechanical kit, side cover (all models) 41N5333 2 Y

Chapter 10. FRU lists 149

Downloaded from www.Manualslib.com manuals search engine

 CRU
7387 FRUs FRU# Tier RoHS?
Mechanical kit (all models) 41N5331 N Y
Main bezel kit (all models) 41N5283 N Y
Power switch/LED assembly (all models) 41N5284 N Y
Shield, system board (all models) 41N5329 N Y
Miscellaneous hardware kit (all models) 41N5334 N Y
Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 N Y
Card Reader Bezel (all models) 41N5340 2 Y

CRU
7387 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS?
US English (models 24U 26U 27U 41U 44U) 41A5289 1 Y
Brazilian (models 23P 24P 41P) 41A5294 1 Y
French Canadian 445 (models 24F 26F 27F 41F 44F) 41A5301 1 Y
French Canadian 58 (models 24F 26F 27F 41F 44F) 41A5302 1 Y
LA Spanish (models 23S 23Y 24S 24Y 41S 41Y 26S 26Y 27S 27Y 44S 44Y) 41A5312 1 Y

CRU
7387 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 21G 22U 22M 25G 28G 42M 42A 45G 21Q) 41A4961 1 Y
Arabic (models 21G 25G 28G 45G) 41A4962 1 Y
Arabic/French (models 21G 25G 28G 45G) 41A4963 1 Y
Belgian/French (models 21G 25G 28G 45G) 41A4964 1 Y
Belgian/UK (models 21G 25G 28G 45G) 41A4965 1 Y
Brazilian (models 22P) 41A4966 1 Y
Bulgarian (models 21G 25G 28G 45G) 41A4967 1 Y
Hong Kong/Taiwan (models 21B 43V) 41A4968 1 Y
Czech (models 21G 25G 28G 45G) 41A4969 1 Y
Danish (models 21G 25G 28G 45G) 41A4970 1 Y
Dutch (models 21G 25G 28G 45G) 41A4971 1 Y
French (models 21G 25G 28G 45G) 41A4972 1 Y
German (models 21G 25G 28G 45G) 41A4975 1 Y
Greek (models 21G 25G 28G 45G) 41A4976 1 Y
Hebrew (models 21G 25G 28G 45G) 41A4977 1 Y
Hungarian (models 21G 25G 28G 45G) 41A4978 1 Y
Iceland (models 21G 25G 28G 45G) 41A4979 1 Y
Italian (models 21G 25G 28G 45G) 41A4980 1 Y
LA Spanish (models 22S) 41A4983 1 Y
Norwegian (models 21G 25G 28G 45G) 41A4984 1 Y
Polish (models 21G 25G 28G 45G) 41A4985 1 Y
Portuguese (models 21G 25G 28G 45G) 41A4986 1 Y
Romanian (models 21G 25G 28G 45G) 41A4987 1 Y

150 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7387 Keyboards (USB, Productivity) FRU# Tier RoHS?
Russian/Cy (models 21G 25G 28G 45G) 41A4988 1 Y
Serbian/Cyrillic (models 21G 25G 28G 45G) 41A4989 1 Y
Slovak (models 21G 25G 28G 45G) 41A4990 1 Y
Spanish (models 21G 25G 28G 45G) 41A4991 1 Y
Swedish/Finn (models 21G 25G 28G 45G) 41A4992 1 Y
Swiss F/G (models 21G 25G 28G 45G) 41A4993 1 Y
Thailand (models 42T) 41A4994 1 Y
Turkish 440 (models 21G 25G 28G 45G) 41A4995 1 Y
Turkish 179 (models 21G 25G 28G 45G) 41A4996 1 Y
UK English (models 21G 25G 28G 45G) 41A4997 1 Y
US Euro (models 21G 25G 28G 45G) 41A4998 1 Y
Slovenian (models 21G 25G 28G 45G) 41A4999 1 Y

CRU
7387 mice FRU# Tier RoHS?
Mouse, USB Optical Wheel (all models) 41A5085 1 Y
Mouse, USB Optical Wheel - Logitec (all models) 41A5089 1 Y

CRU
7387 Adapters and miscellaneous FRUs FRU# Tier RoHS?
PCI Modem Card (Soft) (models 24U 24F 24S 24Y 26U 26F 26S 26P) 29R9729 2 Y
56KBPS Soft Modem - ATX (models 24U 24F 24S 24Y 26U 26F) 41X5334 2 Y
L1 IEEE 1394 PCI Adapter (models 45G) 41D2781 2 Y
ATI X300SE 128MB (models 28G 42M 42A 42T 43V) 39J9635 2 Y
ATI X700 PRO 128MB (models 45G) 39J6203 2 Y
Internal USB Memory Card Reader (models 24U 24F 24S 24P 24Y 25G 26U 26F 41X2089 2 Y
28G 42M 42A 42T 43V 44U 44F 45G 26S 26Y 27S 27Y 44S 44Y)
Speakers (2-piece) (Lenovo logo) (models 24U 24F 24S 24P 24Y 26U 26F 44U 44F 41A5331 1 Y
26S 26Y 44S 44Y)
Speakers (2-piece) (Lenovo logo) (models 24U 24F 24S 24P 24Y 26U 26F 44U 44F 41A5334 1 Y
26S 26Y 44S 44Y)
Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 24U 24F 24S 89P8571 1 Y
24Y 26U 26F 44U 44F)
Speaker Power brick - Brazil (models 24P) 89P8583 1 Y
Speaker Power brick - Argentina (models 24S 24Y) 41A4901 1 Y

CRU
7387 Power Cords FRU# Tier RoHS?
Power Cord (US) (models 22U 22S 23S 24U 24F 24S 26U 26F 27U 27F 41U 41F 41S 39M5080 1 Y
42A 42T 44U 44F 26S 27S 28S)
Power Cord (Brazil) (models 22P 23P 24P 41P) 39M5232 1 Y
Power Cord (LA High Volt (APU) (models 23Y 24Y 41Y 26Y 27Y 44Y) 39M5067 1 Y

Chapter 10. FRU lists 151

Downloaded from www.Manualslib.com manuals search engine

 CRU
7387 Power Cords FRU# Tier RoHS?
Power Cord (Australia, New Zealand) (models 22M 42M) 39M5102 1 Y
Power Cord (Hong Kong) (models 21B) 39M5151 1 Y
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 21G 25G 28G 42A 39M5150 1 Y
45G)
Power Cord (Taiwan) (models 43V) 39M5246 1 Y
Power Cord (Italy) (models 21G 22S 23S 23Y 24S 24Y 25G 28G 41S 41Y 45G 26S 39M5164 1 Y
26Y 27S 27Y 44S 44Y)
Power Cord (G models) (models 21G 25G 28G 42A 45G) 39M5122 1 Y
Power Cord (Denmark) (models 21G 25G 28G 45G) 39M5129 1 Y
Power Cord (Switzerland) (models 21G 25G 28G 45G) 39M5157 1 Y
Power Cord (Israel) (models 21G 25G 28G 45G) 39M5171 1 Y
Power Cord (South Africa) (models 21G 22M 25G 28G 42M 42A 45G) 39M5143 1 Y
Power Cord (India) (models 21Q) 41R3175 1 Y

7387 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 24U 25G 26U 44U 45G) 42Y3480 1
RE (models 25G 45G) 42Y3486 1
FR/CF (models 24F 25G 26F 44F 45G) 42Y3413 1
GR (models 25G 45G) 42Y4314 1
SP/LA (models 24S 24Y 25G 45G 26S 26Y 44S 44Y) 42Y4315 1
IT (models 25G 45G) 42Y4316 1
BR (models 24P) 42Y4317 1
AE (models 25G 45G) 42Y4318 1
RU (models 25G 45G) 42Y4319 1
SV (models 25G 45G) 42Y4320 1
DK (models 25G 45G) 42Y4321 1
FI (models 25G 45G) 42Y4322 1
NO (models 25G 45G) 42Y4323 1
NL (models 25G 45G) 42Y4324 1
CZ (models 25G 45G) 42Y4325 1
HE (models 25G 45G) 42Y4326 1
PL (models 25G 45G) 42Y4327 1
TR (models 25G 45G) 42Y4328 1
HU (models 25G 45G) 42Y4329 1
PO (models 25G 45G) 42Y4330 1
GK (models 25G 45G) 42Y4331 1

7387 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 21G 22U 22M 27U 28G 41U 42M 42A 42T 21Q 9GU 8DG 2EM 42Y3466 1
2JU 2MU 48U 49U 4BA 4BQ 4GM)
RE (models 21G 28G 8DG) 42Y3473 1

152 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7387 Windows XP Pro Recovery CDs FRU# CRU Tier
FR/CF (models 21G 27F 28G 41F 9GF 8DG 2JF 2MF 48F 49F) 42Y4193 1
GR (models 21G 28G 8DG) 42Y4194 1
SP/LA (models 21G 22S 23S 23Y 28G 41S 41Y 27S 27Y 9PS 9PY 9SD 8ES 8EY 8GD 2DS 42Y4195 1
2DY 2NS 2NY 2SD 2PS 2PY 2UD 47S 47Y 9BG)
IT (models 21G 28G 8DG) 42Y4196 1
BR (models 21G 28G 8DG 41P 9QP 8FP 4CP 2RP 2TP 4EP) 42Y4197 1
AE (models 21G 28G 8DG) 42Y4198 1
RU (models 21G 28G 8DG) 42Y4199 1
SV (models 21G 28G 8DG) 42Y4200 1
DK (models 21G 28G 8DG) 42Y4201 1
FI (models 21G 28G 8DG) 42Y4202 1
NO (models 21G 28G 8DG) 42Y4203 1
NL (models 21G 28G 8DG) 42Y4204 1
CZ (models 21G 28G 8DG) 42Y4205 1
HE (models 21G 28G 8DG) 42Y4206 1
PL (models 21G 28G 8DG) 42Y4207 1
TR (models 21G 28G 8DG) 42Y4208 1
HU (models 21G 28G 8DG) 42Y4209 1
PO (models 21G 28G 8DG) 42Y4210 1
GK (models 21G 28G 8DG) 42Y4211 1
SL (models 21G 28G 8DG) 42Y4212 1
Taiwan - TC (models 43V 2FV 4FV) 42T8695 1
Hong Kong - TC (models 21B) 42T8702 1
Korea (models 4FK) 42T8688 1
Multilingual 1 (models 21G 28G 8DG) 42Y4427 1
Multilingual 2 (models 21G 28G 8DG) 42Y4428 1

7387 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier

US (models 9FU 9HU 2BU 4AU 9BG) 87H4730 1
FR/CF (models 9FF 9HF 2BF 4AF 9BG) 87H4731 1
GR (models 9BG ) 87H4732 1
SP/LA (models 9PS 9PY 9SD 8ES 8EY 8GD 2DS 2DY 2NS 2NY 2SD 2PS 2PY 2UD 47S 47Y 87H4733 1
9BG)
BR (models 9QP 8FP 4CP 2RP 2TP 4EP) 87H4734 1
IT (models 9BG) 87H4735 1
RE (models 9BG) 43C0611 1
NO (models 9BG) 87H4737 1
SV (models 9BG) 87H4738 1
DK (models 9BG) 87H4739 1
NL (models 9BG) 87H4740 1
CZ (models 9BG) 87H4741 1

Chapter 10. FRU lists 153

Downloaded from www.Manualslib.com manuals search engine

 7387 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier
FI (models 9BG) 87H4742 1
PL (models 9BG) 87H4743 1
RU (models 9BG) 87H4744 1
TR (models 9BG) 87H4745 1
HU (models 9BG) 87H4746 1
GK (models 9BG) 87H4747 1
PO (models 9BG) 87H4748 1
SL (models 9BG) 87H4752 1

7387 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 2GH) 87H4753 1
HK (models 2GB) 87H4773 1

7387 Vista Business 32 Recovery DVDs FRU# CRU Tier

US (models 9GU 8DG 2EM 2JU 2MU 48U 49U 4BA 4BQ 4GM) 87H4776 1
FR/CF (models 9GF 8DG 2JF 2MF 48F 49F) 87H4777 1
GR (Models 8DG) 87H4778 1
SP/LA (models 8DG 8NS 8NY 8QD 2CS 2CY 2QS 2QY 2VD 46S 46Y) 87H4779 1
BR (models 8PP 2HP 2YP 4DP) 87H4780 1
IT (Models 8DG) 87H4781 1
RE (Models 8DG) 43C0615 1
NO (Models 8DG) 87H4783 1
SV (Models 8DG) 87H4784 1
DK (Models 8DG) 87H4785 1
NL (Models 8DG) 87H4786 1
CZ (Models 8DG) 87H4787 1
FI (Models 8DG) 87H4788 1
PL (Models 8DG) 87H4789 1
RU (Models 8DG) 87H4790 1
TR (Models 8DG) 87H4791 1
HU (Models 8DG) 87H4792 1
GK (Models 8DG) 87H4793 1
PO (Models 8DG) 87H4794 1
TW (models 2FV 4FV) 87H4795 1
KR (models 4FK) 87H4797 1
SL (models 8DG) 87H4798 1

7387 Corel Education CDs FRU# CRU Tier

US (models 22U 22M 24U 26U 27U 41U 42M 42A 42T 44U) 41X0440 1
CF (models 24F 26F 27F 41F 44F) 41X0443 1
LA (models 22S 23S 23Y 24S 24Y 41S 41Y 26S 26Y 27S 27Y 44S 44Y) 41X0446 1

154 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7387 Corel Education CDs FRU# CRU Tier
BR (models 22P 23P 24P 41P) 41X0449 1

Chapter 10. FRU lists 155

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7388

Item CRU
# 7388 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y
2 Microprocessor, 3800+ Athlon64 AM2 X2 (2.0 GHz processor, 89W) 41X4241 N Y
(models 21G 22G)
2 Microprocessor, 4200+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) 41X1421 N Y
(models 41G)
3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
21G)
3 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 22G 41X4252 2 Y
41G)
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 5AG 6AG) 41X3547 N Y
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 5AG 6AG) 41X3548 N Y
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 5AG 6AG 5BG 41X3549 N Y
6BG)
4 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 5AG 6AG 5BG 42Y9368 N Y
6BG)
4 PATA Combo RoHS TS-H492C (VISTA FW) (models 5AG 6AG 5BG 6BG) 42Y9369 N Y
4 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 21G 22G 41X3550 N Y
23G)
4 HLDS RoHS RAMBO-8 drive (models 21G 22G 23G) 42Y9371 N Y
4 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 21G 22G 23G) 43C0144 N Y
5 Diskette drive, w/bezel (models)
6 Front panel card (USB/Audio) assembly (all models) 41N5330 N Y
7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 21G 22G 41G) 40Y9036 N Y
8 System board, nVidia C51g (models 21G 22G 5AG 6AG 5BG 6BG) 45C3619 N Y

156 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7388 FRUs FRU# Tier RoHS?
9 System Fan, rear w/grill (all models) 41N5339 N Y
10 Power supply, 280W, ATX, Standard (models 21G 22G 41G) 41N3479 N Y

The FRUs listed in the following table are not illustrated.

CRU
7388 FRUs FRU# Tier RoHS?
Cable, SATA 250mm (all models) 41A7145 2 Y
Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 2 Y
IDE cable for Tower (2-drop) (all models) 41A7140 2 Y
Modem Phone Cable (all models) 39K5120 2 Y
Cable, diskette drive (RoHs) (all models) 41A7130 2 Y
Mechanical kit, side cover (all models) 41N5333 2 Y
Mechanical kit (all models) 41N5331 N Y
Main bezel kit (all models) 41N5283 N Y
Power switch/LED assembly (all models) 41N5284 N Y
Shield, system board (all models) 41N5329 N Y
Miscellaneous hardware kit (all models) 41N5334 N Y
Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 N Y
Card Reader Bezel (all models) 41N5340 2 Y

CRU
7388 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 21G 22G 41G) 41A4961 1 Y
Arabic (models 21G 22G 41G) 41A4962 1 Y
Arabic/French (models 21G 22G 41G) 41A4963 1 Y
Belgian/French (models 21G 22G 41G) 41A4964 1 Y
Belgian/UK (models 21G 22G 41G) 41A4965 1 Y
Bulgarian (models 21G 22G 41G) 41A4967 1 Y
Czech (models 21G 22G 41G) 41A4969 1 Y
Danish (models 21G 22G 41G) 41A4970 1 Y
Dutch (models 21G 22G 41G) 41A4971 1 Y
French (models 21G 22G 41G) 41A4972 1 Y
German (models 21G 22G 41G) 41A4975 1 Y
Greek (models 21G 22G 41G) 41A4976 1 Y
Hebrew (models 21G 22G 41G) 41A4977 1 Y
Hungarian (models 21G 22G 41G) 41A4978 1 Y
Iceland (models 21G 22G 41G) 41A4979 1 Y
Italian (models 21G 22G 41G) 41A4980 1 Y
Norwegian (models 21G 22G 41G) 41A4984 1 Y
Polish (models 21G 22G 41G) 41A4985 1 Y

Chapter 10. FRU lists 157

Downloaded from www.Manualslib.com manuals search engine

 CRU
7388 Keyboards (USB, Productivity) FRU# Tier RoHS?
Portuguese (models 21G 22G 41G) 41A4986 1 Y
Romanian (models 21G 22G 41G) 41A4987 1 Y
Russian/Cy (models 21G 22G 41G) 41A4988 1 Y
Serbian/Cyrillic (models 21G 22G 41G) 41A4989 1 Y
Slovak (models 21G 22G 41G) 41A4990 1 Y
Spanish (models 21G 22G 41G) 41A4991 1 Y
Swedish/Finn (models 21G 22G 41G) 41A4992 1 Y
Swiss F/G (models 21G 22G 41G) 41A4993 1 Y
Turkish 440 (models 21G 22G 41G) 41A4995 1 Y
Turkish 179 (models 21G 22G 41G) 41A4996 1 Y
UK English (models 21G 22G 41G) 41A4997 1 Y
US Euro (models 21G 22G 41G) 41A4998 1 Y
Slovenian (models 21G 22G 41G) 41A4999 1 Y

CRU
7388 mice FRU# Tier RoHS?
Mouse, USB Optical Wheel (all models) 41A5085 1 Y
Mouse, USB Optical Wheel - Logitec (all models) 41A5089 1 Y

CRU
7388 Adapters and miscellaneous FRUs FRU# Tier RoHS?
L1 IEEE 1394 PCI Adapter (models 41G) 41D2781 2 Y
ATI X300SE 128MB (models 22G) 39J9635 2 Y
ATI X700 PRO 128MB (models 41G) 39J6203 2 Y
Internal USB Memory Card Reader (models 21G 22G 41G) 41X2089 2 Y

CRU
7388 Power Cords FRU# Tier RoHS?
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 21G 22G41G) 39M5150 1 Y
Power Cord (Italy) (models 21G 22G41G) 39M5164 1 Y
Power Cord (G models) (models 21G 22G41G) 39M5122 1 Y
Power Cord (Denmark) (models 21G 22G41G) 39M5129 1 Y
Power Cord (Switzerland) (models 21G 22G41G) 39M5157 1 Y
Power Cord (Israel) (models 21G 22G41G) 39M5171 1 Y
Power Cord (South Africa) (models 21G 22G41G) 39M5143 1 Y

7388 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 21G 41G) 42Y3480 1
RE (models 21G 41G) 42Y3486 1
FR/CF (models 21G 41G) 42Y3413 1
GR (models 21G 41G) 42Y4314 1

158 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7388 Windows XP Home Recovery CDs FRU# CRU Tier
SP/LA (models 21G 41G) 42Y4315 1
IT (models 21G 41G) 42Y4316 1
AE (models 21G 41G) 42Y4318 1
RU (models 21G 41G) 42Y4319 1
SV (models 21G 41G) 42Y4320 1
DK (models 21G 41G) 42Y4321 1
FI (models 21G 41G) 42Y4322 1
NO (models 21G 41G) 42Y4323 1
NL (models 21G 41G) 42Y4324 1
CZ (models 21G 41G) 42Y4325 1
HE (models 21G 41G) 42Y4326 1
PL (models 21G 41G) 42Y4327 1
TR (models 21G 41G) 42Y4328 1
HU (models 21G 41G) 42Y4329 1
PO (models 21G 41G) 42Y4330 1
GK (models 21G 41G) 42Y4331 1

7388 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 22G 6BG) 42Y3466 1
RE (models 22G 6BG) 42Y3473 1
FR/CF (models 22G 6BG) 42Y4193 1
GR (models 22G 6BG) 42Y4194 1
SP/LA (models 22G 6BG) 42Y4195 1
IT (models 22G 6BG) 42Y4196 1
AE (models 22G 6BG) 42Y4198 1
RU (models 22G 6BG) 42Y4199 1
SV (models 22G 6BG) 42Y4200 1
DK (models 22G 6BG) 42Y4201 1
FI (models 22G 6BG) 42Y4202 1
NO (models 22G 6BG) 42Y4203 1
NL (models 22G 6BG) 42Y4204 1
CZ (models 22G 6BG) 42Y4205 1
HE (models 22G 6BG) 42Y4206 1
PL (models 22G 6BG) 42Y4207 1
TR (models 22G 6BG) 42Y4208 1
HU (models 22G 6BG) 42Y4209 1
PO (models 22G 6BG) 42Y4210 1
GK (models 22G 6BG) 42Y4211 1
SL (models 22G 6BG) 42Y4212 1
Multilingual 1 (models 22G 6BG) 42Y4427 1
Multilingual 2 (models 22G 6BG) 42Y4428 1

Chapter 10. FRU lists 159

Downloaded from www.Manualslib.com manuals search engine

 7388 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier
US/UK/AP/TH (models 5BG) 87H4730 1
FR/CF (models 5BG) 87H4731 1
GR (models 5BG) 87H4732 1
SP/LA (models 5BG) 87H4733 1
IT (models 5BG) 87H4735 1
RE (models 5BG) 43C0611 1
NO (models 5BG) 87H4737 1
SV (models 5BG) 87H4738 1
DK (models 5BG) 87H4739 1
NL (models 5BG) 87H4740 1
CZ (models 5BG) 87H4741 1
FI (models 5BG) 87H4742 1
PL (models 5BG) 87H4743 1
RU (models 5BG) 87H4744 1
TR (models 5BG) 87H4745 1
HU (models 5BG) 87H4746 1
GK (models 5BG) 87H4747 1
PO (models 5BG) 87H4748 1
SL (models 5BG) 87H4752 1

7388 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 6BG) 87H4776 1
FR/CF (models 6BG) 87H4777 1
GR (models 6BG) 87H4778 1
SP/LA (models 6BG) 87H4779 1
IT (models 6BG) 87H4781 1
RE (models 6BG) 43C0615 1
JP (models 6BG) 87H4782 1
NO (models 6BG) 87H4783 1
SV (models 6BG) 87H4784 1
DK (models 6BG) 87H4785 1
NL (models 6BG) 87H4786 1
CZ (models 6BG) 87H4787 1
FI (models 6BG) 87H4788 1
PL (models 6BG) 87H4789 1
RU (models 6BG) 87H4790 1
TR (models 6BG) 87H4791 1
HU (models 6BG) 87H4792 1
GK (models 6BG) 87H4793 1
PO (models 6BG) 87H4794 1

160 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7388 Vista Business 32 Recovery DVDs FRU# CRU Tier
SL (models 6BG) 87H4798 1

CRU
7388 Corel Education CDs FRU# Tier RoHS?
US (models 22U 22M 24U 26U 27U 41U 42M 42A 42T 44U) 41X0440 1 Y
CF (models 24F 26F 27F 41F 44F) 41X0443 1 Y
LA (models 22S 23S 23Y 24S 24Y 41S 41Y) 41X0446 1 Y
BR (models 22P 23P 24P 41P) 41X0449 1 Y

Machine Type 7389

Item CRU
# 7389 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y
2 Microprocessor, 4200+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) 41X1421 N Y
(models 41M 41A 42V)
3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
41M 41A 42V)
4 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 41M 41A 41X3550 N Y
42V 6AG 43G)
4 HLDS RoHS RAMBO-8 drive (models 41M 41A 42V 6AG 43G 44A 44T 42Y9371 N Y
6BG 4AG 4BG)
4 PBDS/Lite-ON Rambo 8 (models 41M 41A 42V 6AG 43G 44A 44T 6BG 42Y6017 N Y
4AG 4BG)
5 Diskette drive, w/bezel (models)
6 Front panel card (USB/Audio) assembly (all models) 41N5330 N Y

Chapter 10. FRU lists 161

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7389 FRUs FRU# Tier RoHS?
7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 41M 41A 42V) 40Y9036 N Y
8 System board, nVidia C51g (models 41M 41A 42V 6AG 43G 44A 44T 6BG 45C3619 N Y
4AG 4BG)
9 System Fan, rear w/grill (all models) 41N5339 N Y
10 Power supply, 280W, ATX, Standard (models 41M 41A) 41N3479 N Y
10 Power supply, 280W, Robust (models 42V) 41N3482 N Y

The FRUs listed in the following table are not illustrated.

CRU
7389 FRUs FRU# Tier RoHS?
Cable, SATA 250mm (all models) 41A7145 2 Y
Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 2 Y
IDE cable for Tower (2-drop) (all models) 41A7140 2 Y
Modem Phone Cable (all models) 39K5120 2 Y
Cable, diskette drive (RoHs) (all models) 41A7130 2 Y
Mechanical kit, side cover (all models) 41N5333 2 Y
Mechanical kit (all models) 41N5331 N Y
Main bezel kit (all models) 41N5283 N Y
Power switch/LED assembly (all models) 41N5284 N Y
Shield, system board (all models) 41N5329 N Y
Miscellaneous hardware kit (all models) 41N5334 N Y
Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 N Y
Card Reader Bezel (all models) 41N5340 2 Y

CRU
7389 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 41M 41A) 41A4961 1 Y
Hong Kong/Taiwan (models 42V) 41A4968 1 Y

CRU
7389 mice FRU# Tier RoHS?
Mouse, USB Optical Wheel (all models) 41A5085 1 Y
Mouse, USB Optical Wheel - Logitec (all models) 41A5089 1 Y

CRU
7389 Adapters and miscellaneous FRUs FRU# Tier RoHS?
ATI X300SE 128MB (models 41M 41A 42V) 39J9635 2 Y
Internal USB Memory Card Reader (models 41M 41A 42V) 41X2089 2 Y

162 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7389 Power Cords FRU# Tier RoHS?
Power Cord (US) (models 41A) 39M5080 1 Y
Power Cord (Australia/New Zealand) (models 41M) 39M5102 1 Y
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 41A) 39M5150 1 Y
Power Cord (Taiwan) (models 42V) 39M5246 1 Y
Power Cord (G models) (models 41A) 39M5122 1 Y
Power Cord (South Africa) (models 41M 41A) 39M5143 1 Y

7389 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 41M 41A 6BG 44A) 42Y3466 1
RE (models 6BG) 42Y3473 1
FR/CF (models 6BG) 42Y4193 1
GR (models 6BG) 42Y4194 1
SP/LA (models 6BG) 42Y4195 1
IT (models 6BG) 42Y4196 1
AE (models 6BG) 42Y4198 1
RU (models 6BG) 42Y4199 1
SV (models 6BG) 42Y4200 1
DK (models 6BG) 42Y4201 1
FI (models 6BG) 42Y4202 1
NO (models 6BG) 42Y4203 1
NL (models 6BG) 42Y4204 1
CZ (models 6BG) 42Y4205 1
HE (models 6BG) 42Y4206 1
PL (models 6BG) 42Y4207 1
TR (models 6BG) 42Y4208 1
HU (models 6BG) 42Y4209 1
PO (models 6BG) 42Y4210 1
GK (models 6BG) 42Y4211 1
SL (models 6BG) 42Y4212 1
Multilingual 1 (models 6BG) 42Y4427 1
Multilingual 2 (models 6BG) 42Y4428 1

7389 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 4AG 4BG) 87H4730 1
FR/CF (models 4AG 4BG) 87H4731 1
GR (models 4AG 4BG) 87H4732 1
SP/LA (models 4AG 4BG) 87H4733 1
IT (models 4AG 4BG) 87H4735 1
RE (models 4AG 4BG) 43C0611 1
NO (models 4AG 4BG) 87H4737 1

Chapter 10. FRU lists 163

Downloaded from www.Manualslib.com manuals search engine

 7389 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier
SV (models 4AG 4BG) 87H4738 1
DK (models 4AG 4BG) 87H4739 1
NL (models 4AG 4BG) 87H4740 1
CZ (models 4AG 4BG) 87H4741 1
FI (models 4AG 4BG) 87H4742 1
PL (models 4AG 4BG) 87H4743 1
RU (models 4AG 4BG) 87H4744 1
TR (models 4AG 4BG) 87H4745 1
HU (models 4AG 4BG) 87H4746 1
GK (models 4AG 4BG) 87H4747 1
PO (models 4AG 4BG) 87H4748 1
SL (models 4AG 4BG) 87H4752 1

7389 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 6BG 44A) 87H4776 1
FR/CF (models 6BG) 87H4777 1
GR (models 6BG) 87H4778 1
SP/LA (models 6BG) 87H4779 1
IT (models 6BG) 87H4781 1
RE (models 6BG) 43C0615 1
NO (models 6BG) 87H4783 1
SV (models 6BG) 87H4784 1
DK (models 6BG) 87H4785 1
NL (models 6BG) 87H4786 1
CZ (models 6BG) 87H4787 1
FI (models 6BG) 87H4788 1
PL (models 6BG) 87H4789 1
RU (models 6BG) 87H4790 1
TR (models 6BG) 87H4791 1
HU (models 6BG) 87H4792 1
GK (models 6BG) 87H4793 1
PO (models 6BG) 87H4794 1
SL (models 6BG) 87H4798 1

7389 Corel Education CDs FRU# CRU Tier

US (models 41M 41A) 41X0440 1

164 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7390

Item CRU
# 7390 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y
2 Microprocessor, 3800+ Athlon64 AM2 X2 (2.0 GHz processor, 89W) (models 41X4241 N Y
21B 21V 21J 22M 22Q 22H)
2 Microprocessor, 4000+ Athlon64 AM2 X2 (2.0GHz processor, 89W) (models 41X1419 N Y
45S 45D 45Y )
2 Microprocessor, 4200+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) (models 41X1421 N Y
41B 42H)
2 Microprocessor, 4400+ Athlon64 AM2 X2 (2.2 GHz processor, 89W) (models 43C3507 N Y
63S 63D 63Y)
3 DVD-ROM 16x -48x --XP and Vista (models 45S 45D 45Y ) 41X3544 N Y
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 21V 21J 22M 41X3547 N Y
22Q 22H)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 21V 21J 22M 41X3548 N Y
22Q 22H)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 21V 21J 22M 41X3549 N Y
22Q 22H)
3 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 21B 21V 21J 22M 42Y9368 N Y
22H)
3 PATA Combo RoHS TS-H492C (VISTA FW) (models 21B 21V 21J 22M 22H) 42Y9369 N Y
3 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 41B 42H) 41X3550 N Y
3 HLDS RoHS RAMBO-8 drive (models 41B 42H 24V 23M 53H 51B 51H) 42Y9371 N Y
3 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 41B 42H 24V 23M 53H 43C0144 N Y
51B 51H 63S 63D 63Y )
4 Power switch/LED assembly (all models) 41N5269 N Y
5 Hard disk drive, 80GB, 7200rpm Serial ATA (models 45S 45D 45Y ) 40Y9034 N Y
5 Hard disk drive, 160GB, 7200rpm Serial ATA (models 21B 21V 21J 22M 40Y9035 N Y
22Q 22H 63S 63D 63Y)

Chapter 10. FRU lists 165

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7390 FRUs FRU# Tier RoHS?
5 Hard disk drive, 250GB, 7200rpm Serial ATA (models 41B 42H) 40Y9036 N Y
6 Diskette drive, wo/bezel (models)
7 Front I/O (USB/Audio) Cable Assembly (all models) 41N5270 N Y
8 Memory module, 512MB PC2-4200 -533MHz - DDR2 SDRAM (models 21B 41X4251 2 Y
21V 21J 22M 22Q 22H)
8 Memory module, 1GB PC2-4200 -533MHz - DDR2 SDRAM (models 41B 41X 4252 2 Y
42H)
8 Memory module, 512MB DDR2 SDRAM NP Memory (PC 5300) (models 41X4255 2 Y
45S 45D 45Y )
8 Memory module, 1024MB DDR2 SDRAM NP Memory (PC 5300) (models 41X4256 2 Y
63S 63D 63Y )
9 System board, nVidia C51g (models 21B 21V 21J 22M 22Q 22H 41B 42H 45C3619 N Y
24V 23M 53H 51B 51H)
10 Power supply, 220W TFX ; Robust (models 21B 21V 22Q 22H 41B 42H) 41N3493 N Y
10 Power supply, 220W TFX ; Standard (models 22M 45S 45D 45Y 63S 63D 41N3109 N Y
63Y )
10 Power supply, 220W TFX ; Japan (models 21J) 41N3119 N Y

The FRUs listed in the following table are not illustrated.

CRU
7390 FRUs FRU# Tier RoHS?
Modem Phone Cable (all models) 39K5120 N Y
Shield, EMC, 5.25in. drive bay (all models) 41A7162 N Y
Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 N Y
Shield, EMC, diskette drive bay (all models) 41A7146 N Y
Cable, diskette drive (all models) 41A7147 N Y
Cover (all models) 41A7148 2 Y
Chassis Kit Assembly with bezels (all models) 41N5251 N Y
Bezel Assembly kit (all models) 41N5268 2 Y
Fan duct assembly (all models) 41A7151 N Y
Fan Duct assembly (all models) 41R4808 N Y
AMD AM2 Retention Module (all models) 41R2507 N Y
Shield, EMC, system board (all models) 41N5347 N Y
Miscellaneous hardware kit (all models) 41A7155 N Y
Cable, optical drive signal (all models) 41A7158 N Y
Fan assembly, Front (all models) 41A7198 N Y

CRU
7390 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS?
Chinese/US (models 21B 21V) 41A5296 1 Y
Japanese (models 21J) 41A5310 1 Y
LA Spanish (models 63S 63D 63Y 45S 45D 45Y ) 41A5312 1 Y

166 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7390 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 22M 22Q 22H 42H) 41A4961 1 Y
Hong Kong/Taiwan (models 41B) 41A4968 1 Y

CRU
7390 mice FRU# Tier RoHS?
Mouse, USB optical wheel (models B1G 21G D1J D2J D3G E1J D4J 33J D5J 61G 41A5085 1 Y
F1J F2J F3J F4J F5J F6J)

CRU
7390 Adapters and miscellaneous FRUs FRU# Tier RoHS?
L1 IEEE 1394 PCI Adapter (models 41B 42H) 41D2781 1 Y
Internal USB Memory Card Reader (models 21B 21V 21J 22M 22Q 22H 41B 42H) 41X2089 1 Y
Speakers (2-piece) (Lenovo logo) (models 21B 21V 21J 22M 22Q 22H) 41A5334 1 Y
Speakers (2-piece) (Lenovo logo) (models 21B 21V 21J 22M 22Q 22H) 41A5331 1 Y
Speakers (2-piece) (Lenovo logo) (models 21B 21V 21J 22M 22Q 22H) 41A5334 1 Y
Speaker Power brick - China, Thailand (models 21B 22H) 89P8581 1 Y
Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 45S 63S) 89P8571 1 Y
Speaker Power brick - LA high voltage (non-APU) (models 45D 63D) 89P8575 1 Y
Speaker Power brick - Japan (models 21J) 89P8577 1 Y
Speaker Power brick - ANZ (models 22M) 89P8579 1 Y
Speaker Power brick - Hong Kong, EMEA (models 21B 22H) 89P8573 1 Y
Speaker Power brick - Taiwan (models 21V) 41A4905 1 Y
Speaker Power brick - India, South Africa (models 22Q) 89P8585 1 Y

CRU
7390 Power Cords FRU# Tier RoHS?
Power Cord (US) (models 45S 45D 63S 63D) 39M5080 1 Y
Power Cord (Japan) (models 21J) 39M5193 1 Y
Power Cord (Line Cord - LA High Volt (APU)) (models 45Y 63Y ) 39M5067 1 Y
Power Cord (Australia / New Zealand) (models 22M) 39M5102 1 Y
Power Cord (Hong Kong) (models 21B 22H 41B) 39M5151 1 Y
Power Cord (Taiwan) (models 21V) 39M5246 1 Y
Power Cord (Italy) (models 45S 63S 45Y 63Y ) 39M5164 1 Y
Power Cord (South Africa) (models 22M) 39M5143 1 Y

7390 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 42H) 42Y3480 1
Hong Kong - TC (models 41B) 42T8727 1

7390 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 21G) 42Y3466 1

Chapter 10. FRU lists 167

Downloaded from www.Manualslib.com manuals search engine

 7390 Windows XP Pro Recovery CDs FRU# CRU Tier
SP/LA (models 45S 45D 45Y 63S 63D 63Y ) 42Y4195 1
Japanese (models 21J) 42T8681 1
Taiwan -TC (models 21V) 42T8695 1
Hong Kong - TC (models 21B) 42T8702 1

7390 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 23M 53H) 87H4730 1
TW (models 24V) 87H4749 1

7390 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 51H) 87H4753 1
HK (models 51B) 87H4773 1

7390 Vista Business 32 Recovery DVDs FRU# CRU Tier

Spanish (models 63S 63D 63Y) 87H4779 1

CRU
7390 Corel Education CDs FRU# Tier RoHS?
US (models 22M 22Q 22H 42H) 41X0440 1 Y

168 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7392

Item CRU
# 7392 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, AMD Athlon/Sempron (all models) 41R4802 N Y
2 Microprocessor, 3800+ Athlon64 AM2 X2 (2.0 GHz processor, 89W) 41X4241 N Y
(models 21B 22H)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 22H) 41X3547 N Y
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 22H) 41X3548 N Y
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21B 22H) 41X3549 N Y
3 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 21B 22H) 42Y9368 N Y
3 PATA Combo RoHS TS-H492C (VISTA FW) (models 21B 22H) 42Y9369 N Y
3 HLDS RoHS RAMBO-8 drive (models CTO) 42Y9371 N Y
3 HLDS RAMBO-8 GSA-H10N F/W JX07 (models CTO) 43C0144 N Y
4 Power switch/LED assembly (all models) 41N5269 N Y
5 Hard disk drive, 160GB, 7200rpm Serial ATA (models 21B 22H) 40Y9035 N Y
6 Diskette drive, wo/bezel (models)
7 Front I/O (USB/Audio) Cable Assembly (all models) 41N5270 N Y
8 Memory module, 512MB PC2-4200 -533MHz - DDR2 SDRAM (models 21B 41X4251 2 Y
22H)
9 System board, nVidia C51g (models 21B 22H) 45C3619 N Y
10 Power supply, 220W TFX ; Robust (models 21B 22H) 41N3493 N Y

The FRUs listed in the following table are not illustrated.

CRU
7392 FRUs FRU# Tier RoHS?
Modem Phone Cable (all models) 39K5120 N Y
Shield, EMC, 5.25in. drive bay (all models) 41A7162 N Y
Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 N Y

Chapter 10. FRU lists 169

Downloaded from www.Manualslib.com manuals search engine

 CRU
7392 FRUs FRU# Tier RoHS?
Shield, EMC, diskette drive bay (all models) 41A7146 N Y
Cable, diskette drive (all models) 41A7147 N Y
Cover (all models) 41A7148 2 Y
Chassis Kit Assembly with bezels (all models) 41N5251 N Y
Bezel Assembly kit (all models) 41N5268 2 Y
Fan duct assembly (all models) 41A7151 N Y
Fan duct assembly (all models) 41R4808 N Y
Shield, EMC, system board (all models) 41N5347 N Y
Miscellaneous hardware kit (all models) 41A7155 N Y
Cable, optical drive signal (all models) 41A7158 N Y
Fan assembly, Front (all models) 41A7198 N Y

CRU
7392 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 22H) 41A4961 1 Y
Hong Kong/Taiwan (models 21B) 41A4968 1 Y

CRU
7392 mice FRU# Tier RoHS?
Mouse, USB optical wheel (models B1G 21G D1J D2J D3G E1J D4J 33J D5J 61G 41A5085 1 Y
F1J F2J F3J F4J F5J F6J)

CRU
7392 Adapters and miscellaneous FRUs FRU# Tier RoHS?
Internal USB Memory Card Reader (models 21B 22H) 41X2089 1 Y
Speakers (2-piece) (Lenovo logo) (models 21B 22H) 41A5334 1 Y
Speakers (2-piece) (Lenovo logo) (models 21B 22H) 41A5331 1 Y
Speaker Power brick - China, Thailand (models 21B 22H) 89P8581 1 Y
Speaker Power brick - Hong Kong, EMEA (models 21B 22H) 89P8573 1 Y

CRU
7392 Power Cords FRU# Tier RoHS?
Power Cord (Hong Kong) (models 21B 22H) 39M5151 1 Y

7392 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 22H) 42Y3466 1
Hong Kong (models 21B) 42T8702 1

7392 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models) 87H4730 1
FR/CF (models) 87H4731 1

170 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7392 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier
GR (models) 87H4732 1
SP/LA (models) 87H4733 1
BR (models) 87H4734 1
IT (models) 87H4735 1
RE (models) 43C0611 1
JP (models) 87H4736 1
NO (models) 87H4737 1
SV (models) 87H4738 1
DK (models) 87H4739 1
NL (models) 87H4740 1
CZ (models) 87H4741 1
FI (models) 87H4742 1
PL (models) 87H4743 1
RU (models) 87H4744 1
TR (models) 87H4745 1
HU (models) 87H4746 1
GK (models) 87H4747 1
PO (models) 87H4748 1
TW (models) 87H4749 1
HK (models) 87H4750 1
KR (models) 87H4751 1
SL (models) 87H4752 1

7392 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models) 87H4753 1
FR/CF (models) 87H4754 1
GR (models) 87H4755 1
SP/LA (models) 87H4756 1
BR (models) 87H4757 1
IT (models) 87H4758 1
RE (models) 43C0613 1
JP (models) 87H4759 1
NO (models) 87H4760 1
SV (models) 87H4761 1
DK (models) 87H4762 1
NL (models) 87H4763 1
CZ (models) 87H4764 1
FI (models) 87H4765 1
PL (models) 87H4766 1
RU (models) 87H4767 1
TR (models) 87H4768 1

Chapter 10. FRU lists 171

Downloaded from www.Manualslib.com manuals search engine

 7392 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier
HU (models) 87H4769 1
GK (models) 87H4770 1
PO (models) 87H4771 1
TW (models) 87H4772 1
HK (models) 87H4773 1
KR (models) 87H4774 1
SL (models) 87H4775 1

7392 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models) 87H4776 1
FR/CF (models) 87H4777 1
GR (models) 87H4778 1
SP/LA (models) 87H4779 1
BR (models) 87H4780 1
IT (models) 87H4781 1
RE (models) 43C0615 1
JP (models) 87H4782 1
NO (models) 87H4783 1
SV (models) 87H4784 1
DK (models) 87H4785 1
NL (models) 87H4786 1
CZ (models) 87H4787 1
FI (models) 87H4788 1
PL (models) 87H4789 1
RU (models) 87H4790 1
TR (models) 87H4791 1
HU (models) 87H4792 1
GK (models) 87H4793 1
PO (models) 87H4794 1
TW (models) 87H4795 1
HK (models) 87H4796 1
KR (models) 87H4797 1
SL (models) 87H4798 1

CRU
7392 Corel Education CDs FRU# Tier RoHS?
US (models 22H) 41X0440 1 Y

172 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7393

Item CRU
# 7393 FRUs FRU# Tier RoHS?
1 FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 N Y
models)
2 Microprocessor, Pentium E2140 CONROE-L 800/1600MHZ-1M, LGA, 43C1967 N Y
EM64T (models M7S M8S M9S MAS)
2 Microprocessor, Intel 820 - A0 Smithfield (models 21U 21F 21S 21P 21Y 22U 41T1704 N Y
22F 22S 22P 22Y 23V 24U 24F 24S 24P 24Y 25G 26U 26F 27F 22Q 26S 26Y
27S 27Y)
2 Microprocessor, Intel 925 (models 51U 51F 51M 51A 51T 52G 53B 54H 55U 41X2413 N Y
55F 55S 55P 55Y 56U 56F 57G 57V 58G 51S 51Y 56S 56Y 3KA)
2 Microprocessor, CONROE E6300 1066/1860MHZ-2M (models 91G 92M 93V 41X2495 N Y
94B 94H)
3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 21U 41X4251 2 Y
21F 21S 21P 21Y 22U 22F 22S 22P 22Y 23V 24U 24F 24S 24P 24Y 25G 26U
26F 27F 52G 53B 54H 55U 55F 55S 55P 55Y 22Q 26S 26Y 27S 27Y)
3 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 51U 41X4252 2 Y
51F 51M 51A 51T 56U 56F 57G 57V 58G 51S 51Y 56S 56Y 91G 92M 93V 94B
94H)
3 Memory module, 512MB DDR2 SDRAM NP Memory (PC 5300) (models 41X4255 2 Y
M7S M8S M9S MAS)
3 Memory module, 1024MB DDR2 SDRAM NP Memory (PC 5300) (models 41X4256 2 Y
3KA)
4 DVD-ROM 16x -48x (models 42Q 2CQ 5HB 5HH E1S E1P E1Y E2D E6P 41X3544 N Y
E7S E7Y E8D F1U F1F F5S F5P F5Y H6D GHS GHP GHY GTD GRP GJS
GJY GUD MAS)
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 22U 22F 23V 24U 41X3547 N Y
24F 55U 55F 55S 55P 55Y 22Q 94H 95B EAS EAP EAY F7D F8S F8P F8Y
G4S G4P G4Y G5D H6S H6P H6Y H7D 5JS 5JP 5JY HAD 3KA M7S M9S)

Chapter 10. FRU lists 173

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7393 FRUs FRU# Tier RoHS?
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 22U 22F 23V 24U 41X3548 N Y
24F 55U 55F 55S 55P 55Y 22Q 94H 95B EAS EAP EAY F7D F8S F8P F8Y
G4S G4P G4Y G5D H6S H6P H6Y H7D 5JS 5JP 5JY HAD 3KA M7S M9S)
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 22U 22F 23V 24U 41X3549 N Y
24F 55U 55F 55S 55P 55Y 22Q 94H 95B EAS EAP EAY F7D F8S F8P F8Y
G4S G4P G4Y G5D H6S H6P H6Y H7D 5JS 5JP 5JY HAD 3KA M7S M9S)
4 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 22U 22F 23V 24U 42Y9368 N Y
24F 55U 55F 55S 55P 55Y 22Q 94H 95B 2BS 2BP 2BY 2DS 2DP 2DY 5BU
5BF 5CU 5CF 5FH 5GB E3S E3Y E4P E5D EAS EAP EAY F2S F2Y F3P F4D
F7D F8S F8P F8Y G1U G1F G4S G4P G4Y G5D G6P G7S G7Y H1D H2D
H6S H6P H6Y H7D H8P H9S H9Y GNP GAS HAY GPD GCU GCF GFS
GFY GQP GSD GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY
HAD 6GU 6GF 8JU 8JF 3KA M7S M9S)
4 PATA Combo RoHS TS-H492C (VISTA FW) (models 22U 22F 23V 24U 24F 42Y9369 N Y
55U 55F 55S 55P 55Y 22Q 94H 95B 2BS 2BP 2BY 2DS 2DP 2DY 5BU 5BF
5CU 5CF 5FH 5GB E3S E3Y E4P E5D EAS EAP EAY F2S F2Y F3P F4D F7D
F8S F8P F8Y G1U G1F G4S G4P G4Y G5D G6P G7S G7Y H1D H2D H6S
H6P H6Y H7D H8P H9S H9Y GNP GAS HAY GPD GCU GCF GFS GFY
GQP GSD GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY HAD
6GU 6GF 8JU 8JF 3KA M7S M9S)
4 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 26U 26F 27F 41X3550 N Y
51U 51F 51M 51A 51T 56U 56F 57G 57V 51S 51Y 56S 56Y 92M 93V 28G
61G G2V G2K GBM GBA GBQ GBT M8S)
4 HLDS RoHS RAMBO-8 drive (models 26U 26F 27U 27F 51U 51F 51M 51A 42Y9371 N Y
51T 52G 56U 56F 57G 57V 58G 51S 51Y 56S 56Y 92M 93V 28G 61G 59S 59Y
59P 5AS 5AY 5DU 5DF 5KA 5KQ 5KT 5KV 6AU 6AF 8AU 8AF 99V 97M
98B 98H G2U G2F G3H G8B H3S H3Y H4P H5D G2V G2K GBM GBA
GBQ GBT GDU GDF GEU GEF HBY HCD HDS HDP HDY HFS 6HU 6HF
8MV 8MK 8A 8AQ 8KU 8KF HDS HDY HFD M8S)
4 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 26U 26F 27U 27F 51U 51F 43C0144 N Y
51M 51A 51T 52G 56U 56F 57G 57V 58G 51S 51Y 56S 56Y 92M 93V 28G
61G 59S 59Y 59P 5AS 5AY 5DU 5DF 5KA 5KQ 5KT 5KV 6AU 6AF 8AU
8AF 99V 97M 98B 98H G2U G2F G3H G8B H3S H3Y H4P H5D G2V G2K
GBM GBA GBQ GBT GDU GDF GEU GEF HBY HCD HDS HDP HDY
HFS 6HU 6HF 8MV 8MK 8A 8AQ 8KU 8KF HDS HDY HFD M8S)
5 Diskette drive, w/bezel (models)
6 Front panel card (USB/Audio) assembly (all models) 41N5330 N Y
7 Hard disk drive, 80GB, 7200rpm, serial ATA (models 21U 21F 21S 21P 21Y 40Y9034 N Y
53B 54H M9S MAS)
7 Hard disk drive, 160GB, 7200rpm, serial ATA (models 22U 22F 22S 22P 22Y 40Y9035 N Y
23V 24U 24F 24S 24P 24Y 25G 55U 55F 55S 55P 55Y 22Q 94B 94H 3KA M7S
M8S)
7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 26U 26F 27F 51U 51F 40Y9036 N Y
51M 51A 51T 52G 56U 56F 57G 57V 58G 26S 26Y 27S 27Y 51S 51Y 56S 56Y
91G 92M 93V)

174 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7393 FRUs FRU# Tier RoHS?
8 System board, 946GZ D (models 21U 21F 22U 22F 23V 24U 24F 26U 26F 87H4655 N Y
27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G
57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B
2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5AY 5BU 5BF 5CU 5CF
5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA 8AT 99V
97M 98B 98H 3KA M7S M8S M9S MAS E1S E1P E1Y E2D E3S E3Y E4P
E5D E6P E7S E7Y E8D EAS EAP EAD EAY F1U F1F F2S F2Y F3P F4D F5S
F5P F5Y F6D F7D F8S F8P F8Y G1U G1F G2U G2F G3H G8B G4S G4P G4Y
G5D G6P G7S G7Y H1D H2D H3S H3Y H4P H5D H6Y H7D H8P H9S H9Y
GNP GAS GAY GFD G2V G2K GBM GBA GBQ GBT GCU GCF GDU GDF
GEU GEF GFS GFY GQP GSD GHS GHP GHY GTD GRP GJS GJP GUD
GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY HAD HBY HCD
HDS HDP HES 6GU 6GF 6HU 6HF 8MV 8MK 8AM 8AQ 8JU 8JF 8KU
8KF HDS HDY HFD)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ D (models21U 21F 22U 22F 23V 24U 24F 26U 26F 87H4656 N Y
27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G
57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B
2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5AY 5BU 5BF 5CU 5CF
5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA 8AT 99V
97M 98B 98H 3KA M7S M8S M9S MAS E1S E1P E1Y E2D E3S E3Y E4P
E5D E6P E7S E7Y E8D EAS EAP EAD EAY F1U F1F F2S F2Y F3P F4D F5S
F5P F5Y F6D F7D F8S F8P F8Y G1U G1F G2U G2F G3H G8B G4S G4P G4Y
G5D G6P G7S G7Y H1D H2D H3S H3Y H4P H5D H6Y H7D H8P H9S H9Y
GNP GAS GAY GFD G2V G2K GBM GBA GBQ GBT GCU GCF GDU GDF
GEU GEF GFS GFY GQP GSD GHS GHP GHY GTD GRP GJS GJP GUD
GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY HAD HBY HCD
HDS HDP HES 6GU 6GF 6HU 6HF 8MV 8MK 8AM 8AQ 8JU 8JF 8KU
8KF HDS HDY HFD)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ B (models 21U 21F 22U 22F 23V 24U 24F 26U 26F 43C3504 N Y
27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G
57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B
2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5AY 5BU 5BF 5CU 5CF
5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA 8AT 99V
97M 98B 98H 3KA M7S M8S M9S MAS E1S E1P E1Y E2D E3S E3Y E4P
E5D E6P E7S E7Y E8D EAS EAP EAD EAY F1U F1F F2S F2Y F3P F4D F5S
F5P F5Y F6D F7D F8S F8P F8Y G1U G1F G2U G2F G3H G8B G4S G4P G4Y
G5D G6P G7S G7Y H1D H2D H3S H3Y H4P H5D H6Y H7D H8P H9S H9Y
GNP GAS GAY GFD G2V G2K GBM GBA GBQ GBT GCU GCF GDU GDF
GEU GEF GFS GFY GQP GSD GHS GHP GHY GTD GRP GJS GJP GUD
GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY HAD HBY HCD
HDS HDP HES 6GU 6GF 6HU 6HF 8MV 8MK 8AM 8AQ 8JU 8JF 8KU
8KF HDS HDY HFD)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.

Chapter 10. FRU lists 175

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7393 FRUs FRU# Tier RoHS?
8 System board, 946GZ D (models 21U 21F 22U 22F 23V 24U 24F 26U 26F 43C3505 N Y
27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G
57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B
2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5AY 5BU 5BF 5CU 5CF
5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA 8AT 99V
97M 98B 98H 3KA M7S M8S M9S MAS E1S E1P E1Y E2D E3S E3Y E4P
E5D E6P E7S E7Y E8D EAS EAP EAD EAY F1U F1F F2S F2Y F3P F4D F5S
F5P F5Y F6D F7D F8S F8P F8Y G1U G1F G2U G2F G3H G8B G4S G4P G4Y
G5D G6P G7S G7Y H1D H2D H3S H3Y H4P H5D H6Y H7D H8P H9S H9Y
GNP GAS GAY GFD G2V G2K GBM GBA GBQ GBT GCU GCF GDU GDF
GEU GEF GFS GFY GQP GSD GHS GHP GHY GTD GRP GJS GJP GUD
GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY HAD HBY HCD
HDS HDP HES 6GU 6GF 6HU 6HF 8MV 8MK 8AM 8AQ 8JU 8JF 8KU
8KF HDS HDY HFD)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ (models 3KA 21U 21F 22U 22F 23V 24U 24F 26U 26F 45C3282 N Y
27U 27F 51U 51F 51M 51A 51T 53B 54H 55U 55F 55S 55P 55Y 56U 56F 57G
57V 22Q 26S 26Y 27S 27Y 51S 51Y 56S 56Y 92M 93V 94H 28G 61G 95B
2AA 42Q 2BS 2BY 2CQ 2BP 2DS 2DY 2DP 5AS 5AY 5BU 5BF 5CU 5CF
5DU 5DF 5KA 5KQ 5KT 5KV 5FH 5GB 5HB 5HH 6AU 6AF 8AA 8AT 99V
97M 98B 98H M7S M8S M9S MAS E1S E1P E1Y E2D E3S E3Y E4P E5D
E6P E7S E7Y E8D EAS EAP EAD EAY F1U F1F F2S F2Y F3P F4D F5S F5P
F5Y F6D F7D F8S F8P F8Y G1U G1F G2U G2F G3H G8B G4S G4P G4Y
G5D G6P G7S G7Y H1D H2D H3S H3Y H4P H5D H6Y H7D H8P H9S H9Y
GNP GAS GAY GFD G2V G2K GBM GBA GBQ GBT GCU GCF GDU GDF
GEU GEF GFS GFY GQP GSD GHS GHP GHY GTD GRP GJS GJP GUD
GKS GKY GVP GWD GYP GLS GLY 5MD 5JS 5JP 5JY HAD HBY HCD
HDS HDP HES 6GU 6GF 6HU 6HF 8MV 8MK 8AM 8AQ 8JU 8JF 8KU
8KF HDS HDY HFD)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System Fan, rear w/grill (all models) 41N5339 N Y
10 Power supply, 280W, ATX, Standard (models 21U 21F 22U 22F 24U 24F 41N3479 Y Y
25G 26U 26F 27F 51U 51F 51M 51A 51T 52G 55U 55F 56U 56F 57G 58G 26S
26Y 27S 27Y 51S 51Y 56S 56Y 91G 92M 3KA M7S M8S M9S MAS)
10 Power supply, 280W, Robust (models 21S 21P 21Y 22S 22P 22Y 23V 24S 24P 41N3482 N Y
24Y 53B 54H 55S 55P 55Y 57V 22Q 93V 94B 94H)

The FRUs listed in the following table are not illustrated.

CRU
7393 FRUs FRU# Tier RoHS?
Cable, SATA 250mm (all models) 41A7145 2 Y
Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 2 Y
IDE cable for Tower (2-drop) (all models) 41A7140 2 Y
Modem Phone Cable (all models) 39K5120 2 Y
Cable, diskette drive (RoHs) (all models) 41A7130 2 Y
Mechanical kit, side cover (all models) 41N5333 2 Y
Mechanical kit (all models) 41N5331 N Y
Main bezel kit (all models) 41N5283 N Y

176 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7393 FRUs FRU# Tier RoHS?
Power switch/LED assembly (all models) 41N5284 N Y
Shield, system board (945GZ) (all models) 41N5286 N Y
Miscellaneous hardware kit (all models) 41N5334 N Y
Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 N Y
Card Reader Bezel (all models) 41N5340 2 Y

CRU
7393 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS?
US English (models 21U 24U 26U 54H 55U 56U 94H) 41A5289 1 Y
Brazilian (models 21P 24P 55P) 41A5294 1 Y
Chinese/US (models 53B 94B) 41A5296 1 Y
French Canadian 445 (models 21F 24F 26F 27F 55F 56F) 41A5301 1 Y
French Canadian 58 (models 21F 24F 26F 27F 55F 56F) 41A5302 1 Y
LA Spanish (models 21S 21Y 24S 24Y 55S 55Y 26S 26Y 27S 27Y 56S 56Y MAS) 41A5312 1 Y

CRU
7393 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 22U 25G 51U 51M 51A 52G 57G 58G 22Q 91G 92M) 41A4961 1 Y
Arabic (models 25G 52G 57G 58G 91G) 41A4962 1 Y
Arabic/French (models 25G 52G 57G 58G 91G) 41A4963 1 Y
Belgian/French (models 25G 52G 57G 58G 91G) 41A4964 1 Y
Belgian/UK (models 25G 52G 57G 58G 91G) 41A4965 1 Y
Brazilian (models 22P) 41A4966 1 Y
Bulgarian (models 25G 52G 57G 58G 91G) 41A4967 1 Y
Hong Kong/Taiwan (models 23V 57V 93V) 41A4968 1 Y
Czech (models 25G 52G 57G 58G 91G) 41A4969 1 Y
Danish (models 25G 52G 57G 58G 91G) 41A4970 1 Y
Dutch (models 25G 52G 57G 58G 91G) 41A4971 1 Y
French (models 25G 52G 57G 58G 91G) 41A4972 1 Y
French Canadian 445 (models 22F 51F) 41A4973 1 Y
French Canadian 58 (models 22F 51F) 41A4974 1 Y
German (models 25G 52G 57G 58G 91G) 41A4975 1 Y
Greek (models 25G 52G 57G 58G 91G) 41A4976 1 Y
Hebrew (models 25G 52G 57G 58G 91G) 41A4977 1 Y
Hungarian (models 25G 52G 57G 58G 91G) 41A4978 1 Y
Iceland (models 25G 52G 57G 58G 91G) 41A4979 1 Y
Italian (models 25G 52G 57G 58G 91G) 41A4980 1 Y
LA Spanish (models 22S 22Y 51S 51Y 91G 92M 93V) 41A4983 1 Y
Norwegian (models 25G 52G 57G 58G 91G) 41A4984 1 Y
Polish (models 25G 52G 57G 58G 91G) 41A4985 1 Y
Portuguese (models 25G 52G 57G 58G 91G) 41A4986 1 Y

Chapter 10. FRU lists 177

Downloaded from www.Manualslib.com manuals search engine

 CRU
7393 Keyboards (USB, Productivity) FRU# Tier RoHS?
Romanian (models 25G 52G 57G 58G 91G) 41A4987 1 Y
Russian/Cy (models 25G 52G 57G 58G 91G) 41A4988 1 Y
Serbian/Cyrillic (models 25G 52G 57G 58G 91G) 41A4989 1 Y
Slovak (models 25G 52G 57G 58G 91G) 41A4990 1 Y
Spanish (models 25G 52G 57G 58G 91G) 41A4991 1 Y
Swedish/Finn (models 25G 52G 57G 58G 91G) 41A4992 1 Y
Swiss F/G (models 25G 52G 57G 58G 91G) 41A4993 1 Y
Thailand (models 51T) 41A4994 1 Y
Turkish 440 (models 25G 52G 57G 58G 91G) 41A4995 1 Y
Turkish 179 (models 25G 52G 57G 58G 91G) 41A4996 1 Y
UK English (models 25G 52G 57G 58G 91G) 41A4997 1 Y
US Euro (models 25G 52G 57G 58G 91G) 41A4998 1 Y
Slovenian (models 25G 52G 57G 58G 91G) 41A4999 1 Y

CRU
7393 mice FRU# Tier RoHS?
Mouse, USB Optical Wheel (all models) 41A5085 1 Y
Mouse, USB Optical Wheel - Logitec (all models) 41A5089 1 Y

CRU
7393 Adapters and miscellaneous FRUs FRU# Tier RoHS?
PCI Modem Card (Soft) (models 24U 24F 24S 24Y 27F 56U 56F 27S 27Y 56S 56Y ) 29R9729 2 Y
56KBPS Soft Modem - ATX (models 24P) 41X5334 2 Y
L1 IEEE 1394 PCI Adapter (models 58G) 41D2781 2 Y
ATI X300SE 128MB (models 51U 51F 51M 51A 51T 52G 57G 57V 51S 51Y 91G 39J9635 2 Y
92M 93V)
ATI X700 PRO 128MB (models 58G) 39J6203 2 Y
Internal USB Memory Card Reader (models 22U 22F 22S 22P 22Y 23V 24U 24F 41X2089 2 Y
24S 24P 24Y 25G 27F 51U 51F 51M 51A 51T 52G 56U 56F 57G 57V 58G 22Q 27S
27Y 51S 51Y 56S 56Y 91G 92M 93V)
Speakers (2-piece) (Lenovo logo) (models 24U 24F 24S 24P 24Y 27F 56U 56F 27S 41A5331 1 Y
27Y 56S 56Y )
Speakers (2-piece) (Lenovo logo) (models 24U 24F 24S 24P 24Y 27F 56U 56F 27S 41A5334 1 Y
27Y 56S 56Y )
Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 24U 24F 24S 89P8571 1 Y
24Y 27F 56U 56F 3KA MAS M7S M8S M9S)
Speaker Power brick - Brazil (models 24P) 89P8583 1 Y
Speaker Power brick - Argentina (models 24S 24Y) 41A4901 1 Y

CRU
7393 Power Cords FRU# Tier RoHS?
Power Cord (US) (models 21U 21F 21S 22U 22F 22S 24U 24F 24S 26U 26F 27F 51U 39M5080 1 Y
51F 51A 51T 55U 55F 55S 56U 56F 26S 27S 51S 56S 3KA MAS M7S M8S M9S)

178 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7393 Power Cords FRU# Tier RoHS?
Power Cord (Brazil) (models 21P 22P 24P 55P) 39M5232 1 Y
Power Cord (LA High Volt (APU) (models 21Y 22Y 24Y 55Y 26Y 27Y 51Y 56Y) 39M5067 1 Y
Power Cord (Australia, New Zealand) (models 51M 92M) 39M5102 1 Y
Power Cord (Hong Kong) (models 53B 54H 94B 94H) 39M5151 1 Y
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 25G 51A 52G 57G 39M5150 1 Y
58G 91G 3KA)
Power Cord (Taiwan) (models 23V 57V 93V) 39M5246 1 Y
Power Cord (Italy) (models 21S 21Y 22S 22Y 24S 24Y 25G 52G 55S 55Y 57G 58G 39M5164 1 Y
26Y 27Y 51Y 56Y 26S 27S 51S 56S MAS M7S M8S M9S)
Power Cord (G models) (models 25G 51A 52G 57G 58G 3KA) 39M5122 1 Y
Power Cord (Denmark) (models 25G 52G 57G 58G 91G) 39M5129 1 Y
Power Cord (Switzerland) (models 25G 52G 57G 58G 91G) 39M5157 1 Y
Power Cord (Israel) (models 25G 52G 57G 58G 91G) 39M5171 1 Y
Power Cord (South Africa) (models 25G 51M 51A 52G 57G 58G 91G 92M 3KA) 39M5143 1 Y
Power Cord (India) (models 22Q) 41R3175 1 Y

7393 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 24U 25G 56U 58G 94H) 42Y3480 1
RE (models 25G 58G) 42Y3486 1
FR/CF (models 24F 25G 27F 56F 58G) 42Y3413 1
GR (models 25G 58G) 42Y4314 1
SP/LA (models 24S 24Y 25G 58G) 42Y4315 1
IT (models 25G 58G) 42Y4316 1
BR (models 24P) 42Y4317 1
AE (models 25G 58G) 42Y4318 1
RU (models 25G 58G) 42Y4319 1
SV (models 25G 58G) 42Y4320 1
DK (models 25G 58G) 42Y4321 1
FI (models 25G 58G) 42Y4322 1
NO (models 25G 58G) 42Y4323 1
NL (models 25G 58G) 42Y4324 1
CZ (models 25G 58G) 42Y4325 1
HE (models 25G 58G) 42Y4326 1
PL (models 25G 58G) 42Y4327 1
TR (models 25G 58G) 42Y4328 1
HU (models 25G 58G) 42Y4329 1
PO (models 25G 58G) 42Y4330 1
GK (models 25G 58G) 42Y4331 1
Taiwan - TC (models 93V) TBD 1
Hong Kong - TC (models 94B) TBD 1

Chapter 10. FRU lists 179

Downloaded from www.Manualslib.com manuals search engine

 7393 Windows XP Pro Recovery CDs FRU# CRU Tier
US/UK/AP/TH (models 21U 22U 26U 51U 51M 51A 51T 52G 54H 55U 57G 22Q 91G 92M 42Y3466 1
3KA 42Q F1U G1U G2U 2CQ GCU GDU 5BU 5DU 5FH 5HH 6GU 8AM 8AA 8AQ 97M)
RE (models 52G 57G 91G) 42Y3473 1
FR/CF (models 21F 22F 26F 51F 52G 55F 57G 91G F1F G1F G2F GCF GDF 5BF 5DF 6GF) 42Y4193 1
GR (models 52G 57G 91G) 42Y4194 1
SP/LA (models 21S 21Y 22S 22Y 52G 55S 55Y 57G 26S 26Y 51S 51Y 91G M7S M9S E7S E7Y 42Y4195 1
E8D G7S G7Y H2D 2DS 2DY GJS GJY GUD GLS GLY 5MD HBY HCD HDS HES HDY
HFD )
IT (models 52G 57G 91G) 42Y4196 1
BR (models E6P G6P 2EP GRP GYP HDP) 42Y4197 1
AE (models 52G 57G 91G) 42Y4198 1
RU (models 52G 57G 91G) 42Y4199 1
SV (models 52G 57G 91G) 42Y4200 1
DK (models 52G 57G 91G) 42Y4201 1
FI (models 52G 57G 91G) 42Y4202 1
NO (models 52G 57G 91G) 42Y4203 1
NL (models 52G 57G 91G) 42Y4204 1
CZ (models 52G 57G 91G) 42Y4205 1
HE (models 52G 57G 91G) 42Y4206 1
PL (models 52G 57G 91G) 42Y4207 1
TR (models 52G 57G 91G) 42Y4208 1
HU (models 52G 57G 91G) 42Y4209 1
PO (models 52G 57G 91G) 42Y4210 1
GK (models 52G 57G 91G) 42Y4211 1
SL (models 52G 57G 91G) 42Y4212 1
Taiwan - TC (models 23V 8MV 99V) 42T8695 1
Hong Kong - TC (models 53B 5GB 5HB ) 42T8702 1
Korea (models 8MK) 42T8688 1
Multilingual 1 (models 52G 57G 91G) 42Y4427 1
Multilingual 2 (models 52G 57G 91G) 42Y4428 1

7393 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models G3H GEU 5CU 5KA 5KQ 6AU) 87H4730 1
FR/CF (models GEF 5CF 6AF) 87H4731 1
SP/LA (models E3S E3Y E5D F2S F2Y F4D H1D H3S H3Y H5D H9S H9Y GAS GAY GPD 87H4733 1
GFS GFY GSD GKS GKY GWD 5AS 5AY MAS)
BR (models E4P F3P H4P H8P GNP GQP GVP) 87H4734 1
TW (models 5KV) 87H4749 1
HK (models G8B) 87H4750 1

7393 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 6HU 8KU 98H) 87H4753 1

180 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7393 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier
FR/CF (models GHF 8KF) 87H4754 1
HK (models 98B) 87H4773 1

7393 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 42Q F1U G1U G2U 2CQ GCU GDU 5BU 5DU 5FH 5HH 6GU 87H4776 1
8AM 8AA 8AQ 97M)
FR/CF (models F1F G1F G2F GCF GDF 5BF 5DF 6GF) 87H4777 1
SP/LA (models E7S E7Y E8D G7S G7Y H2D 2DS 2DY GJS GJY GUD GLS GLY 5MD HBY 87H4779 1
HCD HDS HES HDY HFD)
BR (models E6P G6P 2EP GRP GYP HDP) 87H4780 1
TW (models 8MV 99V) 87H4795 1
HK (models 5GB 5HB) 87H4796 1
KR (models 8MK) 87H4797 1

7393 Corel Education CDs FRU# CRU Tier

US (models 21U 22U 24U 26U 51U 51M 51A 51T 54H 55U 56U) 41X0440 1
CF (models 21F 22F 24F 26F 27F 51F 55F 56F) 41X0443 1
LA (models 21S 21Y 22S 22Y 24S 24Y 55S 55Y 27S 27Y 26S 26Y 51S 51Y 56S 56Y ) 41X0446 1
BR (models 21P 22P 24P 55P) 41X0449 1

Machine Type 7394

Chapter 10. FRU lists 181

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7394 FRUs FRU# Tier RoHS?
1 FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 N Y
models)
2 Microprocessor, Intel 820 - A0 Smithfield (models 21G) 41T1704 N Y
2 Microprocessor, Intel 925 (models 41G 42G) 41X2413 N Y
3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
21G)
3 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 41G 41X4252 2 Y
42G 91G)
4 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 21G 42G) 41X3550 N Y
4 PATA RAMBO-8 RoHS SW-9587 (VISTA FW) (models 21G 42G 94A 94T 42Y9370 N Y
22G 51G)
4 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 21G 42G 94A 94T 22G 43C0144 N Y
51G)
5 Diskette drive, w/bezel (models)
6 Front panel card (USB/Audio) assembly (all models) 41N5330 N Y
7 Hard disk drive, 160GB, 7200rpm, serial ATA (models 21G) 40Y9035 N Y
7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 41G 42G 91G) 40Y9036 N Y
8 System board, 946GZ D (models 21G 42G 94A 94T 22G 51G) 87H4655 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ D (models 21G 42G 94A 94T 22G 51G) 87H4656 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ B (models 21G 42G 94A 94T 22G 51G) 43C3504 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ D (models 21G 42G 94A 94T 22G 51G) 43C3505 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ D (models 21G 42G 94A 94T 22G 51G) 43C3505 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ (models 21G 42G 94A 94T 22G 51G) 45C3282 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System Fan, rear w/grill (all models) 41N5339 N Y
10 Power supply, 280W, ATX, Standard (models 21G 41G 42G 91G) 41N3479 Y Y

The FRUs listed in the following table are not illustrated.

CRU
7394 FRUs FRU# Tier RoHS?
Cable, SATA 250mm (all models) 41A7145 2 Y
Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 2 Y
IDE cable for Tower (2-drop) (all models) 41A7140 2 Y
Modem Phone Cable (all models) 39K5120 2 Y

182 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7394 FRUs FRU# Tier RoHS?
Cable, diskette drive (RoHs) (all models) 41A7130 2 Y
Mechanical kit, side cover (all models) 41N5333 2 Y
Mechanical kit (all models) 41N5331 N Y
Main bezel kit (all models) 41N5283 N Y
Power switch/LED assembly (all models) 41N5284 N Y
Shield, system board (945GZ) (all models) 41N5286 N Y
Miscellaneous hardware kit (all models) 41N5334 N Y
Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 N Y
Card Reader Bezel (all models) 41N5340 2 Y

CRU
7394 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 21G 41G 42G 91G) 41A4961 1 Y
Arabic (models 21G 41G 42G 91G) 41A4962 1 Y
Arabic/French (models 21G 41G 42G 91G) 41A4963 1 Y
Belgian/French (models 21G 41G 42G 91G) 41A4964 1 Y
Belgian/UK (models 21G 41G 42G 91G) 41A4965 1 Y
Bulgarian (models 21G 41G 42G 91G) 41A4967 1 Y
Czech (models 21G 41G 42G 91G) 41A4969 1 Y
Danish (models 21G 41G 42G 91G) 41A4970 1 Y
Dutch (models 21G 41G 42G 91G) 41A4971 1 Y
French (models 21G 41G 42G 91G) 41A4972 1 Y
German (models 21G 41G 42G 91G) 41A4975 1 Y
Greek (models 21G 41G 42G 91G) 41A4976 1 Y
Hebrew (models 21G 41G 42G 91G) 41A4977 1 Y
Hungarian (models 21G 41G 42G 91G) 41A4978 1 Y
Iceland (models 21G 41G 42G 91G) 41A4979 1 Y
Italian (models 21G 41G 42G 91G) 41A4980 1 Y
Norwegian (models 21G 41G 42G 91G) 41A4984 1 Y
Polish (models 21G 41G 42G 91G) 41A4985 1 Y
Portuguese (models 21G 41G 42G 91G) 41A4986 1 Y
Romanian (models 21G 41G 42G 91G) 41A4987 1 Y
Russian/Cy (models 21G 41G 42G 91G) 41A4988 1 Y
Serbian/Cyrillic (models 21G 41G 42G 91G) 41A4989 1 Y
Slovak (models 21G 41G 42G 91G) 41A4990 1 Y
Spanish (models 21G 41G 42G 91G) 41A4991 1 Y
Swedish/Finn (models 21G 41G 42G 91G) 41A4992 1 Y
Swiss F/G (models 21G 41G 42G 91G) 41A4993 1 Y
Turkish 440 (models 21G 41G 42G 91G) 41A4995 1 Y
Turkish 179 (models 21G 41G 42G 91G) 41A4996 1 Y

Chapter 10. FRU lists 183

Downloaded from www.Manualslib.com manuals search engine

 CRU
7394 Keyboards (USB, Productivity) FRU# Tier RoHS?
UK English (models 21G 41G 42G 91G) 41A4997 1 Y
US Euro (models 21G 41G 42G 91G) 41A4998 1 Y
Slovenian (models 21G 41G 42G 91G) 41A4999 1 Y

CRU
7394 mice FRU# Tier RoHS?
Mouse, USB Optical Wheel (all models) 41A5085 1 Y
Mouse, USB Optical Wheel - Logitec (all models) 41A5089 1 Y

CRU
7394 Adapters and miscellaneous FRUs FRU# Tier RoHS?
L1 IEEE 1394 PCI Adapter (models 21G 41G) 41D2781 2 Y
ATI X300SE 128MB (models 42G 91G) 39J9635 2 Y
ATI X700 PRO 128MB (models 41G) 39J6203 2 Y
Internal USB Memory Card Reader (models 21G 41G 42G 91G) 41X2089 2 Y

CRU
7394 Power Cords FRU# Tier RoHS?
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 21G 41G 42G 39M5150 1 Y
91G)
Power Cord (Italy) (models 21G 41G 42G 91G) 39M5164 1 Y
Power Cord (G models) (models 21G 41G 42G 91G) 39M5122 1 Y
Power Cord (Denmark) (models 21G 41G 42G 91G) 39M5129 1 Y
Power Cord (Switzerland) (models 21G 41G 42G 91G) 39M5157 1 Y
Power Cord (Israel) (models 21G 41G 42G 91G) 39M5171 1 Y
Power Cord (South Africa) (models 21G 41G 42G 91G) 39M5143 1 Y

7394 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 21G 41G) 42Y3480 1
RE (models 21G 41G) 42Y3486 1
FR/CF (models 21G 41G) 42Y3413 1
GR (models 21G 41G) 42Y4314 1
SP/LA (models 21G 41G) 42Y4315 1
IT (models 21G 41G) 42Y4316 1
AE (models 21G 41G) 42Y4318 1
RU (models 21G 41G) 42Y4319 1
SV (models 21G 41G) 42Y4320 1
DK (models 21G 41G) 42Y4321 1
FI (models 21G 41G) 42Y4322 1
NO (models 21G 41G) 42Y4323 1
NL (models 21G 41G) 42Y4324 1

184 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7394 Windows XP Home Recovery CDs FRU# CRU Tier
CZ (models 21G 41G) 42Y4325 1
HE (models 21G 41G) 42Y4326 1
PL (models 21G 41G) 42Y4327 1
TR (models 21G 41G) 42Y4328 1
HU (models 21G 41G) 42Y4329 1
PO (models 21G 41G) 42Y4330 1
GK (models 21G 41G) 42Y4331 1

7394 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 42G 91G 94A) 42Y3466 1
RE (models 42G 91G) 42Y3473 1
FR/CF (models 42G 91G) 42Y4193 1
GR (models 42G 91G) 42Y4194 1
SP/LA (models 42G 91G) 42Y4195 1
IT (models 42G 91G) 42Y4196 1
AE (models 42G 91G) 42Y4198 1
RU (models 42G 91G) 42Y4199 1
SV (models 42G 91G) 42Y4200 1
DK (models 42G 91G) 42Y4201 1
FI (models 42G 91G) 42Y4202 1
NO (models 42G 91G) 42Y4203 1
NL (models 42G 91G) 42Y4204 1
CZ (models 42G 91G) 42Y4205 1
HE (models 42G 91G) 42Y4206 1
PL (models 42G 91G) 42Y4207 1
TR (models 42G 91G) 42Y4208 1
HU (models 42G 91G) 42Y4209 1
PO (models 42G 91G) 42Y4210 1
GK (models 42G 91G) 42Y4211 1
SL (models 42G 91G) 42Y4212 1
Multilingual 1 (models 42G 91G) 42Y4427 1
Multilingual 2 (models 42G 91G) 42Y4428 1

7394 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 94A) 87H4776 1

Chapter 10. FRU lists 185

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7395

Item CRU
# 7395 FRUs FRU# Tier RoHS?
1 FRU, Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 N Y
models)
2 Microprocessor, Intel 820 - A0 Smithfield (models 21M 21A 22V) 41T1704 N Y
2 Microprocessor, Intel 925 (models 41B 42H 43M 43A 44V) 41X2413 N Y
2 Microprocessor, CONROE E6300 1066/1860MHZ-2M (models 91S 91P 91Y 41X2495 N Y
91M 91B 91H)
3 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
21M 21A 22V 41B 42H)
3 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 43M 41X4252 2 Y
43A 44V 91S 91P 91Y 91M 91B 91H)
4 DVD-ROM 16x -48x (models 25M 23A 23Q 46Q 46B 96B 9AH) 41X3544 N Y
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21M 21A 22V) 41X3547 N Y
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21M 21A 22V) 41X3548 N Y
4 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21M 21A 22V) 41X3549 N Y
4 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 21M 21A 22V 24A 42Y9368 N Y
24T)
4 PATA Combo RoHS TS-H492C (VISTA FW) (models 21M 21A 22V 24A 24T) 42Y9369 N Y
4 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 43M 43A 41X3550 N Y
44V 91M 91H 94B 92A 92T 93Q)
4 HLDS RoHS RAMBO-8 drive (models 43M 43A 44V 91M 91H 94B 45G 42Y9371 N Y
98M 95A 95T 49G 99G 92A 92T 93Q)
4 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 43M 43A 44V 91M 91H 43C0144 N Y
94B 45G 98M 95A 95T 49G 99G 92A 92T 93Q)
5 Diskette drive, w/bezel (models)

186 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7395 FRUs FRU# Tier RoHS?
6 Front panel card (USB/Audio) assembly (all models) 41N5330 N Y
7 Hard disk drive, 80GB, 7200rpm, serial ATA (models 41B 42H) 40Y9034 N Y
7 Hard disk drive, 160GB, 7200rpm, serial ATA (models 21M 21A 22V) 40Y9035 N Y
7 Hard disk drive, 250GB, 7200rpm, serial ATA (models 43M 43A 44V 91S 40Y9036 N Y
91P 91Y 91M 91B 91H)
8 System board, 946GZ D (models 21M 21A 22V 41B 42H 43M 43A 44V 91M 87H4655 N Y
91H 94B 25M 23A 23Q 24A 24T 45G 46Q 46B 98M 95A 95T 96B 49G 9AH
99G 27G 92A 92T 93Q)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ D (models 21M 21A 22V 41B 42H 43M 43A 44V 91M 87H4656 N Y
91H 94B 25M 23A 23Q 24A 24T 45G 46Q 46B 98M 95A 95T 96B 49G 9AH
99G 27G 92A 92T 93Q)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ B (models 21M 21A 22V 41B 42H 43M 43A 44V 91M 43C3504 N Y
91H 94B 25M 23A 23Q 24A 24T 45G 46Q 46B 98M 95A 95T 96B 49G 9AH
99G 27G 92A 92T 93Q)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ D (models 21M 21A 22V 41B 42H 43M 43A 44V 91M 43C3505 N Y
91H 94B 25M 23A 23Q 24A 24T 45G 46Q 46B 98M 95A 95T 96B 49G 9AH
99G 27G 92A 92T 93Q)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
8 System board, 946GZ (models 21M 21A 22V 41B 42H 43M 43A 44V 91M 45C3282 N Y
91H 94B 25M 23A 23Q 24A 24T 45G 46Q 46B 98M 95A 95T 96B 49G 9AH
99G 27G 92A 92T 93Q)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System Fan, rear w/grill (all models) 41N5339 N Y
10 Power supply, 280W, ATX, Standard (models 21M 21A 43M 43A 91S 91P 41N3479 Y Y
91Y 91M)
10 Power supply, 280W, Robust (models 22V 41B 42H 44V 91B 91H) 41N3482 N Y

The FRUs listed in the following table are not illustrated.

CRU
7395 FRUs FRU# Tier RoHS?
Cable, SATA 250mm (all models) 41A7145 2 Y
Luxshare SATA cable, 457mm, 1 latching for Device, RoHS (all models) 26K1186 2 Y
IDE cable for Tower (2-drop) (all models) 41A7140 2 Y
Modem Phone Cable (all models) 39K5120 2 Y
Cable, diskette drive (RoHs) (all models) 41A7130 2 Y
Mechanical kit, side cover (all models) 41N5333 2 Y
Mechanical kit (all models) 41N5331 N Y
Main bezel kit (all models) 41N5283 N Y
Power switch/LED assembly (all models) 41N5284 N Y

Chapter 10. FRU lists 187

Downloaded from www.Manualslib.com manuals search engine

 CRU
7395 FRUs FRU# Tier RoHS?
Shield, system board (945GZ) (all models) 41N5286 N Y
Miscellaneous hardware kit (all models) 41N5334 N Y
Cable, hard disk drive and optical drive signal (2-drop) (all models) 41A7875 N Y
Card Reader Bezel (all models) 41N5340 2 Y
Dongle Cable - DMS59 to dual VGA (all models) 41D2399 2 Y
Battery 3V-lithium (all models) 33F8354 2 Y

CRU
7395 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS?
US English (models 42H) 41A5289 1 Y
Chinese/US (models 41B) 41A5296 1 Y

CRU
7395 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 43M 43A 91M 91H) 41A4961 1 Y
Brazilian (models 91P) 41A4966 1 Y
Hong Kong/Taiwan (models 44V 91B) 41A4968 1 Y
LA Spanish (models 91S 91Y) 41A4983 1 Y

CRU
7395 Keyboards (Fingerprint Reader, USB) FRU# Tier RoHS?
US English (models 21M 21A) 41A5248 1 Y
Chinese/US (models 22V) 41A5255 1 Y

CRU
7395 mice FRU# Tier RoHS?
Mouse, USB Optical Wheel (all models) 41A5085 1 Y
Mouse, USB Optical Wheel - Logitec (all models) 41A5089 1 Y

CRU
7395 Adapters and miscellaneous FRUs FRU# Tier RoHS?
ATI X300SE 128MB (models 43M 43A 44V) 39J9635 2 Y
Boston - ATI X700 PRO 128MB (models 91S 91P 91Y 91M 91B 91H) 39J6203 2 Y
Internal USB Memory Card Reader (models 21M 21A 22V 43M 43A 44V 91S 91P 41X2089 2 Y
91Y 91M 91B 91H)

CRU
7395 Power Cords FRU# Tier RoHS?
Power Cord (US) (models 21A 43A 91S) 39M5080 1 Y
Power Cord (Brazil) (models 91P) 39M5232 1 Y
Power Cord (LA High Volt) (non-APU) (models 91Y) 39M5067 1 Y
Power Cord (Australia, New Zealand) (models 21M 43M 91M) 39M5102 1 Y

188 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7395 Power Cords FRU# Tier RoHS?
Power Cord (Hong Kong) (models 41B 42H 91B 91H) 39M5151 1 Y
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 21A 43A) 39M5150 1 Y
Power Cord (Taiwan) (models 22V 44V) 39M5246 1 Y
Power Cord (Italy) (models 91S 91Y) 39M5164 1 Y
Power Cord (G models) (models 21A 43A) 39M5122 1 Y
Power Cord (South Africa) (models 21M 21A 43M 43A 91M) 39M5143 1 Y

7395 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 21M 21A 42H 43M 43A 91M 91H 25M 23A 23Q 24A 46Q 49G 42Y3466 1
98M 95A 9AH 99G)
RE (models 49G 99G) 42Y3473 1
FR/CF (models 49G 99G) 42Y4193 1
GR (models 49G 99G) 42Y4194 1
SP/LA (models 91S 91Y) 42Y4195 1
IT (models 49G 99G) 42Y4196 1
AE (models 49G 99G) 42Y4198 1
RU (models 49G 99G) 42Y4199 1
SV (models 49G 99G) 42Y4200 1
DK (models 49G 99G) 42Y4201 1
FI (models 49G 99G) 42Y4202 1
NO (models 49G 99G) 42Y4203 1
NL (models 49G 99G) 42Y4204 1
CZ (models 49G 99G) 42Y4205 1
HE (models 49G 99G) 42Y4206 1
PL (models 49G 99G) 42Y4207 1
TR (models 49G 99G) 42Y4208 1
HU (models 49G 99G) 42Y4209 1
PO (models 49G 99G) 42Y4210 1
GK (models 49G 99G) 42Y4211 1
SL (models 49G 99G) 42Y4212 1
Multilingual 1 (models 49G 99G) 42Y4427 1
Multilingual 2 (models 49G 99G) 42Y4428 1

7395 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 25M 23A 23Q 24A 46Q 49G 98M 95A 9AH 99G) 87H4776 1
FR/CF (models 49G 99G) 87H4777 1
GR (models 49G 99G) 87H4778 1
SP/LA (models 49G 99G) 87H4779 1
IT (models 49G 99G) 87H4781 1
RE (models 49G 99G) 43C0615 1

Chapter 10. FRU lists 189

Downloaded from www.Manualslib.com manuals search engine

 7395 Vista Business 32 Recovery DVDs FRU# CRU Tier
NO (models 49G 99G) 87H4783 1
SV (models 49G 99G) 87H4784 1
DK (models 49G 99G) 87H4785 1
NL (models 49G 99G) 87H4786 1
CZ (models 49G 99G) 87H4787 1
FI (models 49G 99G) 87H4788 1
PL (models 49G 99G) 87H4789 1
RU (models 49G 99G) 87H4790 1
TR (models 49G 99G) 87H4791 1
HU (models 49G 99G) 87H4792 1
GK (models 49G 99G) 87H4793 1
PO (models 49G 99G) 87H4794 1
HK (models 49G 99G) 87H4796 1
SL (models 49G 99G) 87H4798 1

7395 Corel Education CDs FRU# CRU Tier

US (models 21M 21A 42H 43M 43A) 41X0440 1

Machine Type 7396

Item CRU
# 7396 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 N Y
models)
2 Microprocessor, Celeron 420 CONROE-L 800/1600MHZ-512K,LGA,EM64T 43C3835 N Y
(models 74B 74H)
2 Microprocessor, Pentium E2140 CONROE-L 800/1600MHZ-1M, LGA, 43C1967 N Y
EM64T (models D6S D7S D8S)

190 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7396 FRUs FRU# Tier RoHS?
2 Microprocessor, Pentium E2160 CONROE-L 800/1600MHZ-1M, LGA, 43C1968 N Y
EM64T (models F2B F2H)
2 Microprocessor, Intel 820 - A0 Smithfield (models 21M 21A 21Q 21T 21H 41T1704 N Y
22G 22V 23G 24B 25H)
2 Microprocessor, Intel 925 (models 41M 42G 4CS 4CD 4CY 4FS 4FD 4FY 41X2413 N Y
4GS 4GD 4GY 4JS 4JD 4JY 4KB 4KH )
2 Microprocessor ,CONROE E6300 1066/1860MHZ-2M (models 9DS 9DY 41X2495 N Y
9DD )
3 DVD-ROM 16x -48x --XP and Vista (models 4CS 4CD 4CY 4JS 4JD 4JY 41X3544 N Y
D6S)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21M 21A 21Q 21T 41X3547 N Y
21H 22G 22V)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21M 21A 21Q 21T 41X3548 N Y
21H 22G 22V)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (modIels 21M 21A 21Q 21T 41X3549 N Y
21H 22G 22V)
3 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 21M 21A 21Q 21T 42Y9368 N Y
21H 22G 22V 8AG 8BG 45G)
3 PATA Combo RoHS TS-H492C (VISTA FW) (models 21M 21A 21Q 21T 21H 42Y9369 N Y
22G 22V 8AG 8BG 45G)
3 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 23G 24B 41X3550 N Y
25H 41M 26B 6BV 6AM 6AA 6AT 4GS 4GD 4GY 5FS 5FD 5FY 9DS 9DD
9DY 4KB 4KH 74B 74H F2B F2H D8S)
3 HLDS RoHS RAMBO-8 drive (models 23G 24B 25H 41M 26B 6BV 6AM 42Y9371 N Y
6AA 6AT 4GS 4GD 4GY 5FS 5FD 5FY 9DS 9DD 9DY 4KB 4KH 74B 74H
F2B F2H D8S)
3 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 23G 24B 25H 41M 26B 43C0144 N Y
27M 29B 28H 43M 44B 44H 9AA 9AT 9AV 9BB 9BH 8CB 8CH 6BV 6AM
6AA 6AT 5BV 5CM 5AA 5AT 4GS 4GD 4GY 5FS 5FD 5FY 9DS 9DD 9DY
4KB 4KH 74B 74H F2B F2H D8S)
4 Power switch/LED assembly (all models) 41N5269 N Y
5 Hard disk drive, 80GB, 7200rpm Serial ATA (models 4CS 4CD 4CY 4FS 40Y9034 N Y
4FD 4FY 4JS 4JD 4JY D6S D7S)
5 Hard disk drive, 160GB, 7200rpm Serial ATA (models 21M 21A 21Q 21T 40Y9035 N Y
21H 22G 22V 23G 4GS 4GD 4GY 5FS 5FD 5FY 9DS 9DD 9DY 74B 74H D8S
)
5 Hard disk drive, 250GB, 7200rpm Serial ATA (models 24B 25H 41M 42G 40Y9036 N Y
4KB 4KH F2B F2H )
6 Diskette drive, wo/bezel (models)
7 Front I/O (USB/Audio) Cable Assembly (all models) 41N5270 N Y
8 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
21M 21A 21Q 21T 21H 22G 22V 23G 24B 25H)
8 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 41M 41X4252 2 Y
42G)
8 Memory module, 512MB DDR2 SDRAM NP Memory (PC 5300) (models 41X4255 2 Y
4CS 4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4KB 4KH D6S S7S)
8 Memory module, 1024MB DDR2 SDRAM NP Memory (PC 5300) (models 41X4256 2 Y
41M 42G 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY 74B 74H F2B F2H D8S)

Chapter 10. FRU lists 191

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7396 FRUs FRU# Tier RoHS?
9 System board, 945GZ D - Intel based (models 21M 21A 21Q 21T 21H 22G 87H4655 N Y
22V 23G 24B 25H 41M 8AG 27M 29B 28H 43M 44B 44H 9AA 9AT 9AV
9BB 9BH 8BG 8CB 8CH 6BV 6AM 6AT 6AT 45G 5BV 5CM 5AA 5AT ’4CS
4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD
9DY 4KB 4KH 74B 74H F2B F2H D6S D7S D8S)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 945GZ D - Intel based (models 21M 21A 21Q 21T 21H 22G 87H4656 N Y
22V 23G 24B 25H 41M 8AG 27M 29B 28H 43M 44B 44H 9AA 9AT 9AV
9BB 9BH 8BG 8CB 8CH 6BV 6AM 6AT 6AT 45G 5BV 5CM 5AA 5AT ’4CS
4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD
9DY 4KB 4KH 74B 74H F2B F2H D6S D7S D8S)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ B (models 21M 21A 21Q 21T 21H 22G 22V 23G 24B 43C3504 N Y
25H 41M 8AG 27M 29B 28H 43M 44B 44H 9AA 9AT 9AV 9BB 9BH 8BG
8CB 8CH 6BV 6AM 6AT 6AT 45G 5BV 5CM 5AA 5AT ’4CS 4CD 4CY 4FS
4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY 4KB 4KH
74B 74H F2B F2H D6S D7S D8S)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ D (models 21M 21A 21Q 21T 21H 22G 22V 23G 24B 43C3505 N Y
25H 41M 8AG 27M 29B 28H 43M 44B 44H 9AA 9AT 9AV 9BB 9BH 8BG
8CB 8CH 6BV 6AM 6AT 6AT 45G 5BV 5CM 5AA 5AT ’4CS 4CD 4CY 4FS
4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY 4KB 4KH
74B 74H F2B F2H D6S D7S D8S)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ (models 4CS 4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 45C3282 N Y
4JS 4JD 4JY 21M 21A 21Q 21T 21H 22G 22V 23G 24B 25H 41M 8AG 27M
29B 28H 43M 44B 44H 9AA 9AT 9AV 9BB 9BH 8BG 8CB 8CH 6BV 6AM
6AT 6AT 45G 5BV 5CM 5AA 5AT 9DS 9DD 9DY 4KB 4KH E2B E2H E3B
E3H 74B 74H F2B F2H D6S D7S D8S)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
10 Power supply, 220W TFX ; Robust (models 21Q 21H 22V 24B 25H 4KB 41N3493 N Y
4KH 74B 74H F2B F2H )
10 Power supply, 220W TFX ; Standard (models 21M 21A 21T 22G 23G 41M 41N3109 N Y
42G 4CS 4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 5FD 5FY
9DS 9DD 9DY D6S D7S S8S)

The FRUs listed in the following table are not illustrated.

CRU
7396 FRUs FRU# Tier RoHS?
Modem Phone Cable (all models) 39K5120 N Y
Shield, EMC, 5.25in. drive bay (all models) 41A7162 N Y
Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 N Y
Shield, EMC, diskette drive bay (all models) 41A7146 N Y
Cable, diskette drive (all models) 41A7147 N Y
Cover (all models) 41A7148 2 Y

192 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7396 FRUs FRU# Tier RoHS?
Chassis Kit Assembly with bezels (all models) 41N5251 N Y
Bezel Assembly kit (all models) 41N5268 2 Y
Fan duct assembly (all models) 41A7151 N Y
Fan duct assembly (all models) 41R4808 N Y
Shield, EMC, system board (all models) 41N5347 N Y
Miscellaneous hardware kit (all models) 41A7155 N Y
Cable, optical drive signal (all models) 41A7158 N Y
Fan assembly, Front (all models) 41A7198 N Y
Retention bracket kit, heat sink (for Intel microprocessor) (all models) 41A7139 N Y
Heat sink (all models) 41A7847 N Y
Desktop Card Reader Bezel (all models) 41N5337 N Y
Dongle Cable - DMS59 to dual VGA (all models) 41D2399 2 Y
Battery 3V-lithium (all models) 33F8354 2 Y

CRU
7396 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS?
US English (models 4KH 74H F2H ) 41A5289 1 Y
Chinese/US (models 4KB 74B F2B ) 41A5296 1 Y
LA Spanish (models 4CS 4CD 4CY 4FS 4FD 4FY 4GS 4GD 4GY 4JS 4JD 4JY 5FS 41A5312 1 Y
5FD 5FY 9DS 9DD 9DY D6S D7S D8S)

CRU
7396 Keyboards (USB, Productivity) FRU# Tier RoHS?
US English (models 21M 21A 21Q 21H 22G 23G 25H) 41A4961 1 Y
Arabic (models 22G 23G) 41A4962 1 Y
Arabic/French (models 22G 23G) 41A4963 1 Y
Belgian/French (models 22G 23G) 41A4964 1 Y
Belgian/UK (models 22G 23G) 41A4965 1 Y
Bulgarian (models 22G 23G) 41A4967 1 Y
Hong Kong/Taiwan (models 22V 24B) 41A4968 1 Y
Czech (models 22G 23G) 41A4969 1 Y
Danish (models 22G 23G) 41A4970 1 Y
Dutch (models 22G 23G) 41A4971 1 Y
French (models 22G 23G) 41A4972 1 Y
German (models 22G 23G) 41A4975 1 Y
Greek (models 22G 23G) 41A4976 1 Y
Hebrew (models 22G 23G) 41A4977 1 Y
Hungarian (models 22G 23G) 41A4978 1 Y
Iceland (models 22G 23G) 41A4979 1 Y
Italian (models 22G 23G) 41A4980 1 Y
Norwegian (models 22G 23G) 41A4984 1 Y

Chapter 10. FRU lists 193

Downloaded from www.Manualslib.com manuals search engine

 CRU
7396 Keyboards (USB, Productivity) FRU# Tier RoHS?
Polish (models 22G 23G) 41A4985 1 Y
Portuguese (models 22G 23G) 41A4986 1 Y
Romanian (models 22G 23G) 41A4987 1 Y
Russian/Cy (models 22G 23G) 41A4988 1 Y
Serbian/Cyrillic (models 22G 23G) 41A4989 1 Y
Slovak (models 22G 23G) 41A4990 1 Y
Spanish (models 22G 23G) 41A4991 1 Y
Swedish/Finn (models 22G 23G) 41A4992 1 Y
Swiss F/G (models 22G 23G) 41A4993 1 Y
Thailand (models 21T) 41A4994 1 Y
Turkish 440 (models 22G 23G) 41A4995 1 Y
Turkish 179 (models 22G 23G) 41A4996 1 Y
UK English (models 22G 23G) 41A4997 1 Y
US Euro (models 22G 23G) 41A4998 1 Y
Slovenian (models 22G 23G) 41A4999 1 Y

CRU
7396 Keyboards (Fingerprint Reader, USB) FRU# Tier RoHS?
US English (models 41M 42G) 41A5248 1 Y
Arabic (models 42G) 41A5249 1 Y
Arabic/French (models 42G) 41A5250 1 Y
Belgian/French (models 42G) 41A5251 1 Y
Belgian/UK (models 42G) 41A5252 1 Y
Brazil/Portuguese (models 42G) 41A5253 1 Y
Bulgarian (models 42G) 41A5254 1 Y
Chinese/US (models 42G) 41A5255 1 Y
Czech (models 42G) 41A5256 1 Y
Danish (models 42G) 41A5257 1 Y
Dutch (models 42G) 41A5258 1 Y
French (models 42G) 41A5259 1 Y
French Canadian 445 (models 42G) 41A5260 1 Y
French Canadian 58 (models 42G) 41A5261 1 Y
German (models 42G) 41A5262 1 Y
Greek (models 42G) 41A5263 1 Y
Greek/US (models 42G) 41A5264 1 Y
Hebrew (models 42G) 41A5265 1 Y
Hungarian (models 42G) 41A5266 1 Y
Iceland (models 42G) 41A5267 1 Y
Italian 141 (models 42G) 41A5268 1 Y
Norwegian (models 42G) 41A5272 1 Y

194 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7396 Keyboards (Fingerprint Reader, USB) FRU# Tier RoHS?
Polish (models 42G) 41A5273 1 Y
Portuguese (models 42G) 41A5274 1 Y
Romanian 446 (models 42G) 41A5275 1 Y
Romanian 96 (models 42G) 41A5276 1 Y
Russian/Cy (models 42G) 41A5277 1 Y
Serbian/Cyrillic (models 42G) 41A5278 1 Y
Slovak (models 42G) 41A5279 1 Y
Spanish (models 42G) 41A5280 1 Y
Swedish/Finn (models 42G) 41A5281 1 Y
Swiss F/G (models 42G) 41A5282 1 Y
Turkish 179 (models 42G) 41A5284 1 Y
Turkish 440 (models 42G) 41A5285 1 Y
UK English (models 42G) 41A5286 1 Y
US Euro (models 42G) 41A5287 1 Y
Slovenian (models 42G) 41A5288 1 Y

CRU
7396 mice FRU# Tier RoHS?
Mouse, USB optical wheel (all models) 41A5085 1 Y
Mouse, USB optical wheel - Logitec (all models) 41A5089 1 Y

CRU
7396 Adapters and miscellaneous FRUs FRU# Tier RoHS?
ATI X300SE 128MB (models 41M 42G) 39J9635 1 Y
Internal USB Memory Card Reader (models 21M 21A 21Q 21T 21H 22G 22V 23G 41X2089 1 Y
24B 25H 41M 42G)
Speaker Power brick - US, Canada, LA low voltage, ASEAN (models 4CS 4FS 4GS 89P8571 1 Y
4JS 5FS 9DS D6S D7S D8S)
Speaker Power brick - LA high voltage (non-APU) (models 4CD 4FD 4GD 4JD 89P8575 1 Y
5FD 9DD )
Speaker Brick - Hong Kong, EMEA (models 4KB 4KH 74B 74H F2B F2H ) 89P8573 1 Y

CRU
7396 Power Cords FRU# Tier RoHS?
Power Cord (US) (models 21A 21T 4CS 4FS 4GS 4JS 4CD 4FD 4GD 4JD 5FS 5FD 39M5080 1 Y
9DS 9DD D6S D7S D8S)
Power Cord - LA High Volt (APU) (models 4CY 4FY 4GY 4JY 5FY 9DY) 39M5067 1 Y
Power Cord (Australia, New Zealand) (models 21M 41M) 39M5102 1 Y
Power Cord (Hong Kong) (models 21H 24B 25H 4KB 4KH 74B 74H F2B F2H ) 39M5151 1 Y
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 21A 22G 23G 39M5150 1 Y
42G)
Power Cord (Taiwan) (models 22V) 39M5246 1 Y

Chapter 10. FRU lists 195

Downloaded from www.Manualslib.com manuals search engine

 CRU
7396 Power Cords FRU# Tier RoHS?
Power Cord (Italy) (models 22G 23G 42G 4CS 4FS 4GS 4JS 4CY 4FY 4GY 4JY 5FS 39M5164 1 Y
9DS 5FY 9DY D6S D7S D8S)
Power Cord (G models) (models 21A 22G 23G 42G) 39M5122 1 Y
Power Cord (Denmark) (models 21A 22G 23G 42G) 39M5129 1 Y
Power Cord (Switzerland) (models 21A 22G 23G 42G) 39M5157 1 Y
Power Cord (Israel) (models 21A 22G 23G 42G) 39M5171 1 Y
Power Cord (South Africa) (models 21M 21A 22G 23G 41M 42G) 39M5143 1 Y
Power Cord (India) (models 21Q) 41R3175 1 Y

7396 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 25H) 42Y3480 1
Hong Kong - TC (models 24B) 42T8727 1

7396 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 21M 21A 21Q 21T 21H 22G 23G 41M 42G ^8AG 8BG 27M 43M 42Y3466 1
5CM 5AA )
RE (models 22G 23G 42G 8AG 8BG ) 42Y3473 1
FR/CF (models 22G 23G 42G 8AG 8BG ) 42Y4193 1
GR (models 22G 23G 42G 8AG 8BG ) 42Y4194 1
SP/LA (models 22G 23G 42G 8AG 8BG 4CS 4CD 4CY 4GS 4GD 4GY D6S D8S 4JS 4JD 4JY 42Y4195 1
5FS 5FD 5FY 9DS 9DD 9DY )
IT (models 22G 23G 42G 8AG 8BG ) 42Y4196 1
AE (models 22G 23G 42G 8AG 8BG ) 42Y4198 1
RU (models 22G 23G 42G 8AG 8BG ) 42Y4199 1
SV (models 22G 23G 42G 8AG 8BG ) 42Y4200 1
DK (models 22G 23G 42G 8AG 8BG ) 42Y4201 1
FI (models 22G 23G 42G 8AG 8BG ) 42Y4202 1
NO (models 22G 23G 42G 8AG 8BG ) 42Y4203 1
NL (models 22G 23G 42G 8AG 8BG ) 42Y4204 1
CZ (models 22G 23G 42G 8AG 8BG ) 42Y4205 1
HE (models 22G 23G 42G 8AG 8BG ) 42Y4206 1
PL (models 22G 23G 42G 8AG 8BG ) 42Y4207 1
TR (models 22G 23G 42G 8AG 8BG ) 42Y4208 1
HU (models 22G 23G 42G 8AG 8BG ) 42Y4209 1
PO (models 22G 23G 42G 8AG 8BG ) 42Y4210 1
GK (models 22G 23G 42G 8AG 8BG ) 42Y4211 1
SL (models 22G 23G 42G 8AG 8BG ) 42Y4212 1
Taiwan - TC (models 22V 5BV ) 42T8695 1
Multilingual 1 (models 22G 23G 42G 8AG 8BG ) 42Y4427 1
Multilingual 2 (models 22G 23G 42G 8AG 8BG ) 42Y4428 1

196 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 7396 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier
US/UK/AP/TH (models 8CH 28H 9AA 4KH 74H) 87H4730 1
TW (models 9AV) 87H4749 1
HK (models 8CB 29B 74B) 87H4750 1

7396 Vista Home Premium 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 44H 9BH F2H) 87H4753 1
HK (models 44B 9BB F2B) 87H4773 1

7396 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 8AG 8BG 27M 43M 5CM 5AA) 87H4776 1
FR/CF (models 8AG 8BG) 87H4777 1
GR (models 8AG 8BG) 87H4778 1
SP/LA (models 8AG 8BG D8S 4JS 4JD 4JY 5FS 5FD 5FY 9DS 9DD 9DY ) 87H4779 1
IT (models 8AG 8BG) 87H4781 1
RE (models 8AG 8BG) 43C0615 1
NO (models 8AG 8BG) 87H4783 1
SV (models 8AG 8BG) 87H4784 1
DK (models 8AG 8BG) 87H4785 1
NL (models 8AG 8BG) 87H4786 1
CZ (models 8AG 8BG) 87H4787 1
FI (models 8AG 8BG) 87H4788 1
PL (models 8AG 8BG) 87H4789 1
RU (models 8AG 8BG) 87H4790 1
TR (models 8AG 8BG) 87H4791 1
HU (models 8AG 8BG) 87H4792 1
GK (models 8AG 8BG) 87H4793 1
PO (models 8AG 8BG) 87H4794 1
TW (models 5BV) 87H4795 1
SL (models 8AG 8BG) 87H4798 1

7396 Corel Education CDs FRU# CRU Tier

US (models 21M 21A 21Q 21T 21H 25H 41M) 41X0440 1

Chapter 10. FRU lists 197

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7397

Item CRU
# 7397 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 N Y
models)
2 Microprocessor, Intel 820 - A0 Smithfield (models 21J 22J 23G) 41T1704 N Y
2 Microprocessor, Intel 925 (models 41J 42J 45G) 41X2413 N Y
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21J 22J 8AG 43G 41X3547 N Y
45G)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21J 22J 8AG 43G 41X3548 N Y
45G)
3 Combo 48 -32 -48 -16 - - DVD - ROM - CDRW (models 21J 22J 8AG 43G 41X3549 N Y
45G)
3 PATA Combo RoHS SOHC-4836V (VISTA FW) (models 21J 22J 8AG 8BG 42Y9368 N Y
43G 45G)
3 PATA Combo RoHS TS-H492C (VISTA FW) (models 21J 22J 8AG 8BG 43G 42Y9369 N Y
45G)
3 DVD Recordable - Multi Burner Plus -DVD RAM VIII (models 23G 41J 42J 41X3550 N Y
6AJ 91J 92J)
3 HLDS RoHS RAMBO-8 drive (models 23G 41J 42J 93J 94J 6AJ 5AJ 91J 92J) 42Y9371 N Y
3 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 23G 41J 42J 93J 94J 6AJ 43C0144 N Y
5AJ 91J 92J)
4 Power switch/LED assembly (all models) 41N5269 N Y
5 Hard disk drive, 80GB, 7200rpm Serial ATA (models 45G) 40Y9034 N Y
5 Hard disk drive, 160GB, 7200rpm Serial ATA (models 21J 22J 23G) 40Y9035 N Y
5 Hard disk drive, 250GB, 7200rpm Serial ATA (models 41J 42J) 40Y9036 N Y
6 Diskette drive, wo/bezel (models)
7 Front I/O (USB/Audio) Cable Assembly (all models) 41N5270 N Y
8 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 21J 41X4251 2 Y
22J 23G 45G)

198 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7397 FRUs FRU# Tier RoHS?
8 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 41J 41X4252 2 Y
42J)
9 System board, 945GZ D - Intel based (models 21J 22J 23G 41J 42J 8AG 93J 87H4655 N Y
94J 8BG 6AJ 43G 5AJ 91J 92J)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 945GZ D - Intel based (models 21J 22J 23G 41J 42J 8AG 93J 87H4656 N Y
94J 8BG 6AJ 43G 5AJ 91J 92J)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ B (models 21J 22J 23G 41J 42J 8AG 93J 94J 8BG 6AJ 43C3504 N Y
43G 5AJ 91J 92J)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ D (models 21J 22J 23G 41J 42J 8AG 93J 94J 8BG 6AJ 43C3505 N Y
43G 5AJ 91J 92J)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ D (models 21J 22J 23G 41J 42J 8AG 93J 94J 8BG 6AJ 45C3282 N Y
43G 5AJ 91J 92J)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
10 Power supply, 220W TFX ; Standard (models 23G 45G) 41N3109 N Y
10 Power supply, 220W TFX ; Japan (models 21J 22J 41J 42J) 41N3119 N Y

CRU
7397 FRUs FRU# Tier RoHS?
Modem Phone Cable (all models) 39K5120 N Y
Shield, EMC, 5.25in. drive bay (all models) 41A7162 N Y
Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 N Y
Shield, EMC, diskette drive bay (all models) 41A7146 N Y
Cable, diskette drive (all models) 41A7147 N Y
Cover (all models) 41A7148 2 Y
Chassis Kit Assembly with bezels (all models) 41N5251 N Y
Bezel Assembly kit (all models) 41N5268 2 Y
Fan duct assembly (all models) 41A7151 N Y
Fan duct assembly (all models) 41R4808 N Y
Shield, EMC, system board (all models) 41N5347 N Y
Miscellaneous hardware kit (all models) 41A7155 N Y
Cable, optical drive signal (all models) 41A7158 N Y
Fan assembly, Front (all models) 41A7198 N Y
Retention bracket kit, heat sink (for Intel microprocessor) (all models) 41A7139 N Y
Heat sink (all models) 41A7847 N Y
Desktop Card Reader Bezel (all models) 41N5337 N Y
Dongle Cable - DMS59 to dual VGA (all models) 41D2399 2 Y

Chapter 10. FRU lists 199

Downloaded from www.Manualslib.com manuals search engine

 CRU
7397 FRUs FRU# Tier RoHS?
Battery 3V-lithium (all models) 33F8354 2 Y

CRU
7397 Keyboards (USB Preferred - Fullwidth) FRU# Tier RoHS?
Japanese (models 22J 42J) 41A5310 1 Y

CRU
7397 Keyboards (USB Productivity) FRU# Tier RoHS?
US English (models 23G 45G) 41A4961 1 Y
Arabic (models 23G 45G) 41A4962 1 Y
Arabic/French (models 23G 45G) 41A4963 1 Y
Belgian/French (models 23G 45G) 41A4964 1 Y
Belgian/UK (models 23G 45G) 41A4965 1 Y
Bulgarian (models 23G 45G) 41A4967 1 Y
Czech (models 23G 45G) 41A4969 1 Y
Danish (models 23G 45G) 41A4970 1 Y
Dutch (models 23G 45G) 41A4971 1 Y
French (models 23G 45G) 41A4972 1 Y
German (models 23G 45G) 41A4975 1 Y
Greek (models 23G 45G) 41A4976 1 Y
Hebrew (models 23G 45G) 41A4977 1 Y
Hungarian (models 23G 45G) 41A4978 1 Y
Iceland (models 23G 45G) 41A4979 1 Y
Italian (models 23G 45G) 41A4980 1 Y
Japanese (models 21J 41J) 41A4981 1 Y
Norwegian (models 23G 45G) 41A4984 1 Y
Polish (models 23G 45G) 41A4985 1 Y
Portuguese (models 23G 45G) 41A4986 1 Y
Romanian (models 23G 45G) 41A4987 1 Y
Russian/Cy (models 23G 45G) 41A4988 1 Y
Serbian/Cyrillic (models 23G 45G) 41A4989 1 Y
Slovak (models 23G 45G) 41A4990 1 Y
Spanish (models 23G 45G) 41A4991 1 Y
Swedish/Finn (models 23G 45G) 41A4992 1 Y
Swiss F/G (models 23G 45G) 41A4993 1 Y
Turkish 440 (models 23G 45G) 41A4995 1 Y
Turkish 179 (models 23G 45G) 41A4996 1 Y
UK English (models 23G 45G) 41A4997 1 Y
US Euro (models 23G 45G) 41A4998 1 Y
Slovenian (models 23G 45G) 41A4999 1 Y

200 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7397 mice FRU# Tier RoHS?
Mouse, USB optical wheel (all models) 41A5085 1 Y
Mouse, USB optical wheel - Logitec (all models) 41A5089 1 Y

CRU
7397 Adapters and miscellaneous FRUs FRU# Tier RoHS?
ATI X300SE 128MB (models 41J 42J) 39J9635 1 Y
Internal USB Memory Card Reader (models 21J 23G 41J) 41X2089 1 Y
Speaker Brick - Hong Kong, EMEA (models 45G) 89P8573 1 Y

CRU
7397 Power Cords FRU# Tier RoHS?
Power Cord (Japan) (models 21J 22J 41J 42J) 39M5193 1 Y
Power Cord (UK, Ireland, Singapore, Malaysia, Brunei) (models 23G 45G) 39M5150 1 Y
Power Cord (Italy) (models 23G 45G) 39M5164 1 Y
Power Cord (G models) (models 23G 45G) 39M5122 1 Y
Power Cord (Denmark) (models 23G 45G) 39M5129 1 Y
Power Cord (Switzerland) (models 23G 45G) 39M5157 1 Y
Power Cord (Israel) (models 23G 45G) 39M5171 1 Y
Power Cord (South Africa) (models 23G 45G) 39M5143 1 Y

7397 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 23G 8BG) 42Y3466 1
RE (models 23G 8BG) 42Y3473 1
FR/CF (models 23G 8BG) 42Y4193 1
GR (models 23G 8BG) 42Y4194 1
SP/LA (models 23G 8BG) 42Y4195 1
IT (models 23G 8BG) 42Y4196 1
AE (models 23G 8BG) 42Y4198 1
RU (models 23G 8BG) 42Y4199 1
SV (models 23G 8BG) 42Y4200 1
DK (models 23G 8BG) 42Y4201 1
FI (models 23G 8BG) 42Y4202 1
NO (models 23G 8BG) 42Y4203 1
NL (models 23G 8BG) 42Y4204 1
CZ (models 23G 8BG) 42Y4205 1
HE (models 23G 8BG) 42Y4206 1
PL (models 23G 8BG) 42Y4207 1
TR (models 23G 8BG) 42Y4208 1
HU (models 23G 8BG) 42Y4209 1
PO (models 23G 8BG) 42Y4210 1
GK (models 23G 8BG) 42Y4211 1

Chapter 10. FRU lists 201

Downloaded from www.Manualslib.com manuals search engine

 7397 Windows XP Pro Recovery CDs FRU# CRU Tier
SL (models 23G 8BG) 42Y4212 1
Japanese (models 21J 22J 41J 42J) 42T8681 1
Multilingual 1 (models 23G 8BG) 42Y4427 1
Multilingual 2 (models 23G 8BG) 42Y4428 1

7397 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 8BG) 87H4776 1
FR/CF (models 8BG) 87H4777 1
GR (models 8BG) 87H4778 1
SP/LA (models 8BG) 87H4779 1
IT (models 8BG) 87H4781 1
RE (models 8BG) 43C0615 1
JP (models 5AJ 93J 94J) 87H4782 1
NO (models 8BG) 87H4783 1
SV (models 8BG) 87H4784 1
DK (models 8BG) 87H4785 1
NL (models 8BG) 87H4786 1
CZ (models 8BG) 87H4787 1
FI (models 8BG) 87H4788 1
PL (models 8BG) 87H4789 1
RU (models 8BG) 87H4790 1
TR (models 8BG) 87H4791 1
HU (models 8BG) 87H4792 1
GK (models 8BG) 87H4793 1
PO (models 8BG) 87H4794 1
SL (models 8BG) 87H4798 1

7387 Corel Education CDs FRU# CRU Tier

US (models 22U 22M 24U 26U 27U 41U 42M 42A 42T 44U) 41X0440 1
CF (models 24F 26F 27F 41F 44F) 41X0443 1
LA (models 22S 23S 23Y 24S 24Y 41S 41Y 26S 26Y 27S 27Y 44S 44Y) 41X0446 1
BR (models 22P 23P 24P 41P) 41X0449 1

CRU
7397 Corel Education CDs FRU# Tier RoHS?
JP (models 21J 22J 41J 42J) 41X0484 1 Y

202 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Machine Type 7398

Item CRU
# 7398 FRUs FRU# Tier RoHS?
1 Heat Sink/RM Kit, Intel Prescott, Cedar Mill, Smithfield, Presler (all 41R4803 N Y
models)
2 Microprocessor, Intel 925 (models 41M 42V) 41X2413 N Y
2 Microprocessor, CONROE E6300 1066/1860MHZ-2M (models 91B 91H 92B 41X2495 N Y
92H)
3 DVD Recordable - Multi Burner Plus -DVD RAM VIII--XP (models 41M 41X3550 N Y
42V 91H 92H 93B 94B)
3 HLDS RoHS RAMBO-8 drive (models 41M 42V 91H 92H 93B 94B 97M 95A 42Y9371 N Y
95T 96B 96H)
3 HLDS RAMBO-8 GSA-H10N F/W JX07 (models 41M 42V 91H 92H 93B 43C0144 N Y
94B 97M 95A 95T 96B 96H)
4 Power switch/LED assembly (all models) 41N5269 N Y
5 Hard disk drive, 250GB, 7200rpm Serial ATA (models 41M 42V 91B 91H 40Y9036 N Y
92B 92H)
6 Diskette drive, wo/bezel (models)
7 Front I/O (USB/Audio) Cable Assembly (all models) 41N5270 N Y
8 Memory module, 512MB PC2-4200 - 533MHz - DDR2 SDRAM (models 41X4251 2 Y
41M 42V)
8 Memory module, 1GB PC2-4200 - 533MHz - DDR2 SDRAM (models 91B 41X4252 2 Y
91H 92B 92H)
9 System board, 945GZ D - Intel based (models 41M 42V 91H 92H 93B 94B) 87H6455 N Y
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 945GZ D - Intel based (models 41M 42V 91H 92H 93B 94B 87H6456 N Y
97M 95A 95T 96B 96H)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.

Chapter 10. FRU lists 203

Downloaded from www.Manualslib.com manuals search engine

 Item CRU
# 7398 FRUs FRU# Tier RoHS?
9 System board, 946GZ B (models 41M 42V 91H 92H 93B 94B 97M 95A 95T 43C3504 N Y
96B 96H)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ D (models 41M 42V 91H 92H 93B 94B 97M 95A 95T 43C3505 N Y
96B 96H)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
9 System board, 946GZ D (models 41M 42V 91H 92H 93B 94B 97M 95A 95T 45C3282 N Y
96B 96H)
Note: When you order a new system board you must also order a new
retention bracket for the heat sink.
10 Power supply, 220W TFX ; Robust (models 42V 91B 91H 92B 92H) 41N3493 N Y
10 Power supply, 220W TFX ; Standard (models 41M) 41N3109 N Y

The FRUs listed in the following table are not illustrated.

CRU
7398 FRUs FRU# Tier RoHS?
Modem Phone Cable (all models) 39K5120 N Y
Shield, EMC, 5.25in. drive bay (all models) 41A7162 N Y
Cable, Serial-ATA, (18in. RoHs) (all models) 41A7145 N Y
Shield, EMC, diskette drive bay (all models) 41A7146 N Y
Cable, diskette drive (all models) 41A7147 N Y
Cover (all models) 41A7148 2 Y
Chassis Kit Assembly with bezels (all models) 41N5251 N Y
Bezel Assembly kit (all models) 41N5268 2 Y
Fan duct assembly (all models) 41A7151 N Y
Fan duct assembly (all models) 41R4808 N Y
Shield, EMC, system board (all models) 41N5347 N Y
Miscellaneous hardware kit (all models) 41A7155 N Y
Cable, optical drive signal (all models) 41A7158 N Y
Fan assembly, Front (all models) 41A7198 N Y
Retention bracket kit, heat sink (for Intel microprocessor) (all models) 41A7139 N Y
Heat sink (all models) 41A7847 N Y
Desktop Card Reader Bezel (all models) 41N5337 N Y
Dongle Cable - DMS59 to dual VGA (all models) 41D2399 2 Y
Battery 3V-lithium (all models) 33F8354 2 Y

CRU
7398 Keyboards (USB Productivity) FRU# Tier RoHS?
US English (models 41M 91H 92H) 41A4961 1 Y
Hong Kong/Taiwan (models 42V 91B) 41A4968 1 Y

204 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 CRU
7398 mice FRU# Tier RoHS?
Mouse, USB optical wheel (all models) 41A5085 1 Y
Mouse, USB optical wheel - Logitec (all models) 41A5089 1 Y

CRU
7398 Adapters and miscellaneous FRUs FRU# Tier RoHS?
Internal USB Memory Card Reader (models 41M 42V 91B 91H 92B 92H) 41X2089 1 Y
Boston - ATI X700 PRO 128MB (models 91B 91H 92B 92H) 39J6203 1 Y

CRU
7398 Power Cords FRU# Tier RoHS?
Power Cord (Australia, New Zealand) (models 41M) 39M5102 1 Y
Power Cord (Hong Kong) (models 91B 91H 92B 92H) 39M5151 1 Y
Power Cord (Taiwan) (models 42V) 39M5246 1 Y
Power Cord (South Africa) (models 41M) 39M5143 1 Y

7398 Windows XP Home Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 91H) 42Y3480 1
Hong Kong - TC (models 91B) TBD 1

7398 Windows XP Pro Recovery CDs FRU# CRU Tier

US/UK/AP/TH (models 41M 92H 97M 95A ) 42Y3466 1
Taiwan - TC (models 42V) 42T8695 1
Hong Kong - TC (models 82B) TBD 1

7398 Vista Home Basic 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 96B) 87H4730 1
HK (models 96H) 87H4750 1

7398 Vista Business 32 Recovery DVDs FRU# CRU Tier

US/UK/AP/TH (models 97M 95A) 87H4776 1

7398 Corel Education CDs FRU# CRU Tier

US (models 41M) 41X0440 1

Chapter 10. FRU lists 205

Downloaded from www.Manualslib.com manuals search engine

 206 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Chapter 11. Additional Service Information
This chapter provides additional information that the service representative might
find helpful.

Security features
Security features in this section include the following:
v Passwords
v Vital Product Data
v Management Information Format (MIF)

Hardware controlled Passwords

Hardware controlled passwords are set using the Setup Utility program. For more
information about passwords, see “Using passwords” on page 51.

Operating system password

An operating system password is very similar to a power-on password and denies
access to the computer by an unauthorized user when the password is activated.
The computer is unusable until the password is entered and recognized by the
computer.

Vital product data

Each computer has a unique Vital Product Data (VPD) code stored in the
nonvolatile memory on the system board. After you replace the system board, the
VPD must be updated. To update the VPD, see “Flash update procedures.”

BIOS levels
An incorrect level of BIOS can cause false errors and unnecessary FRU
replacement. Use the following information to determine the current level of BIOS
installed in the computer, the latest BIOS available for the computer, and where to
obtain the latest level of BIOS.
v To determine the current Level of BIOS:
– Start the Setup Utility.
– Select Standard CMOS Features.
v Sources for obtaining the latest level BIOS available
1. Lenovo support web site:
http://www.lenovo.com/support/
2. Lenovo Customer Support Center
3. Levels 1 and 2 Support

To update (flash) the BIOS, see “Flash update procedures.”

Flash update procedures

This section details how to flash (update) the BIOS.

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 207

Downloaded from www.Manualslib.com manuals search engine

 Updating (flashing) BIOS from a diskette
1. Insert a system program update (flash) diskette into the diskette drive. system
program updates are available at http://www.lenovo.com/support on the
World Wide Web.
2. Turn on the computer. If it is already on, you must turn it off and back on. The
update begins.
3. Follow the instructions on the screen to complete the update.

Recovering from a POST/BIOS update failure

Attention: If an interruption occurs during a POST/BIOS update (flash update),
the computer might not restart correctly. If this occurs, perform the following
procedure (also known as a Boot-block recovery).

Note: If the computer has no internal diskette drive, an optional USB diskette
drive must be connected to use the BIOS flash diskette.
1. Turn the computer off and insert the special recovery BIOS flash diskette in the
diskette drive.
2. Turn the computer on.
3. The recovery session takes two to three minutes. During this time you will hear
a series of beeps. After the update session completes, the series of beeps ends
and the computer automatically turns off. There is no video during the
recovery session.
4. Remove the special recovery BIOS flash diskette from the diskette drive.

208 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Power management
Power management reduces the power consumption of certain components of the
computer such as the system power supply, processor, hard disk drives, and some
monitors.

Automatic configuration and power interface (ACPI) BIOS

Being an ACPI BIOS system, the operating system is allowed to control the power
management features of the computer and the setting for Advanced Power
Management (APM) BIOS mode is ignored. Not all operating systems support
ACPI BIOS mode.

Automatic Power-On features

The Automatic Power-On features within the Power Management menu allow you
to enable and disable features that turn on the computer automatically.
v Serial Port A Ring Detect: With this feature set to Enabled and an external
modem connected to serial port (COM1), the computer will turn on
automatically when a ring is detected on the modem.
v PCI Modem Ring Detect: With this feature set to Enabled, the computer will
turn on automatically when a ring is detected on the internal modem.
v PCI Wake Up: This feature allows PCI cards that support this capability to wake
the system.
v Wake Up on Alarm: You can specify a date and time at which the computer will
be turned on automatically. This can be either a single event or a daily event.
v Wake on LAN: If the computer has a properly configured token-ring or Ethernet
LAN adapter card that is Wake on LAN-enabled and there is remote network
management software, you can use the Wake on LAN feature. When you set
Wake on LAN to Enabled, the computer will turn on when it receives a specific
signal from another computer on the local area network (LAN).

Chapter 11. Additional Service Information 209

Downloaded from www.Manualslib.com manuals search engine

 Recovering software
When you install a new hard disk drive, you also need a set of Product Recovery
discs. The set of Product Recovery discs will enable the contents of the hard disk to
be restored to the same state as when the computer was originally shipped from
the factory. For more information on recovering factory-installed software, refer to
“Recovering software” in the User Guide.

210 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

 Appendix. Notices
Lenovo may not offer the products, services, or features discussed in this
document in all countries. Consult your local Lenovo representative for
information on the products and services currently available in your area. Any
reference to a Lenovo product, program, or service is not intended to state or
imply that only that Lenovo product, program, or service may be used. Any
functionally equivalent product, program, or service that does not infringe any
Lenovo intellectual property right may be used instead. However, it is the user’s
responsibility to evaluate and verify the operation of any other product, program,
or service.

Lenovo may have patents or pending patent applications covering subject matter
described in this document. The furnishing of this document does not give you
any license to these patents. You can send license inquiries, in writing, to:
Lenovo (United States), Inc.
500 Park Offices Drive, Hwy. 54
Research Triangle Park, NC 27709
U.S.A.
Attention: Lenovo Director of Licensing

LENOVO GROUP LTD. PROVIDES THIS PUBLICATION “AS IS” WITHOUT

WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT,
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Some
jurisdictions do not allow disclaimer of express or implied warranties in certain
transactions, therefore, this statement may not apply to you.

This information could include technical inaccuracies or typographical errors.

Changes are periodically made to the information herein; these changes will be
incorporated in new editions of the publication. Lenovo may make improvements
and/or changes in the product(s) and/or the program(s) described in this
publication at any time without notice.

The products described in this document are not intended for use in implantation
or other life support applications where malfunction may result in injury or death
to persons. The information contained in this document does not affect or change
Lenovo product specifications or warranties. Nothing in this document shall
operate as an express or implied license or indemnity under the intellectual
property rights of Lenovo or third parties. All information contained in this
document was obtained in specific environments and is presented as an
illustration. The result obtained in other operating environments may vary.

Lenovo may use or distribute any of the information you supply in any way it
believes appropriate without incurring any obligation to you.

Any references in this publication to non-Lenovo Web sites are provided for
convenience only and do not in any manner serve as an endorsement of those Web
sites. The materials at those Web sites are not part of the materials for this Lenovo
product, and use of those Web sites is at your own risk.

Any performance data contained herein was determined in a controlled

environment. Therefore, the result obtained in other operating environments may

© Lenovo 2006. Portions © IBM Corp. 2005, 2006. 211

Downloaded from www.Manualslib.com manuals search engine

 vary significantly. Some measurements may have been made on development-level
systems and there is no guarantee that these measurements will be the same on
generally available systems. Furthermore, some measurements may have been
estimated through extrapolation. Actual results may vary. Users of this document
should verify the applicable data for their specific environment.

Television output notice

The following notice applies to models that have the factory-installed
television-output feature.

This product incorporates copyright protection technology that is protected by

method claims of certain U.S. patents and other intellectual property rights owned
by Macrovision Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision Corporation, and is
intended for home and other limited viewing uses only unless otherwise
authorized by Macrovision Corporation. Reverse engineering or disassembly is
prohibited.

Trademarks
The following terms are trademarks of Lenovo in the United States, other
countries, or both:
Lenovo
Lenovo logo
PS/2
Rescue and Recovery

The following terms are trademarks of International Business Machines

Corporation in the United States, other countries, or both:
IBM (used under license)
Wake on LAN

Intel and Pentium are trademarks of Intel Corporation in the United States, other
countries, or both.

Microsoft and Windows are trademarks of Microsoft Corporation in the United

States, other countries, or both.

Other company, product, or service names may be trademarks or service marks of

others.

212 Lenovo 3000 J Series

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine
 Part Number: 41X8137

Printed in USA

(1P) P/N: 41X8137

Downloaded from www.Manualslib.com manuals search engine