TMS 880M

Product Guide

HYDRAULIC TRUCK CRANE

Features
n
MAX CAPACITY (Outriggers) - 80 Tonnes at n
MAX. ROAD SPEED - 49 km/hr
3m Radius (85% Rating) 360° Slew n
CARRIER - 8x4 Drive
n
BOOM - 5 Section formed full power boom 12.1m - 43.8m
- 10.1m Fixed lattice extension (optional)
- 17.1m Tele lattice extension (optional)
 Superstructure Specifications

BOOM HYDRAULIC SYSTEM

5-section, telescopic, formed, full power, sequenced Pump - 3 sec. gear pump driven through gearbox PTO.
synchronized boom. Fabricated from high strength low 2 sec. gear pump engine driven.
alloy steel plates. Telescopic sections slide on adjustable and Valves - Precision four way double acting control valves, four
replaceable low friction wear resistance pads. individual valve banks permit simultaneous control of multiple
Telescoping Range: 12.1m- 43.8m crane functions.
Maximum Tip Height: 46.0m for main boom Filter - Return line type, full flow with bypass protection and
- 56.0 m with 10.1m fixed lattice extension service indicator. Replaceable cartridge.
- 63.0 m with 17.1m tele lattice extension Reservoir - 900 liters capacity fitted with filter, external sight
BOOM NOSE gauge, clean out access, strap mounted to frame.
Five nylatron sheaves mounted on heavy duty tapered roller Oil Cooler - Remote mounted, thermostatically controlled
bearings with removable pin-type rope guards. electric motor driven fan.
BOOM ELEVATION Pressure Check Panel - System pressure test panel permits
Two double acting hydraulic cylinders with integral holding easy verification of circuit pressure.
valves.
LOAD MOMENT INDICATOR & ANTI-TWO BLOCK
BOOM ANGLE SYSTEM
Maximum 78°, Minimum -1.0°. Electronic load moment indicator system with audio-visual
SUPERSTRUCTURE FRAME warning & control lever lockout indicates electronic display of
Fabricated from high tensile steel plates and sections. boom angle, length, radius, relative load moment, permissible
load, load indication & warning of impending two block
SLEW SYSTEM condition. Motion cut off to ensure the safe operation with
Ball bearing swing circle with 360° continuous rotation. load for tele, derrick & hoist motions.
Planetary glide swing with foot applied multi-disc wet brake.
Spring applied hydraulically released parking brake, mechanical SAFETY SYSTEM
house lock operated from cab. Free slew facility provided. Pendant Limit Switch on boom head for over hoist. Third wrap
indicator on hoist barrel to ensure 3 turns of rope on hoist
SLEW SPEED drum. Hydraulic relief valves protect pumps and structures
Maximum 1.5 RPM (Unladen) from excessive pressure. Lock and counter balance valves
HOIST SYSTEM fitted on derrick, telescopic and outrigger cylinders to sustain
Power up and down, equal speed, planetary reduction with rams in the event of hydraulic failure.
integral automatic spring applied multidisc brake on grooved
OPERATOR’S CAB
hoist barrel. Hoist drum fitted with third wrap indicator.
Totally enclosed steel construction, full vision type, windows
Maximum Single Line Pull - Hoist Drum fitted with toughened safety glass including front windscreen.
1st Layer: 9200kg, 2nd Layer: 8400kg, 3rd Layer: 7727kg Adjustable operator’s seat, cab interior light, electric fan,
4th Layer: 7155kg, 5th Layer: 6664kg
electric horn, electric windshield wiper and lockable sliding
Maximum Single Line Pull - Hoist Rope door. Ergonomically designed cab and controller layout to give
7250kg with 18 x 19 class rope fatigue free comfort to the operator.
Maximum Single Line Speed:
130 m/min. (Unladen) - Top layer OPTIONAL EQUIPMENT
Non Spin Hoist Rope: Auxiliary Hoist Unit
Rope length 229 m and 19 mm (3/4”) dia. Air Conditioned super cabin
Air Conditioned carrier cabin
HOOK BLOCK
10.1m Fixed Lattice
80 MT, 6 sheaves
17.1m Tele Lattice
COUNTERWEIGHT 40T / 50T Hook Block (Loose Supply)
TMS 880M

6000 kg 15T Single Sheave Hook Block (Loose Supply)

CRANE CONTROLS 6.8T Headache Ball
Joystick controls are in operator’s cab for slewing, telescoping, Tie Down Rope
hoisting and derricking with independent or simultaneous Anemometer
operation of crane motions. 5 Kg Fire Extinguisher

Technical Specification TIL/TMS880M/1019

2
Height of Lift : 5 Section 12.1m-43.8m Full Power Boom
: 10.1m Fixed Lattice Extension
: 17.1m Tele Lattice Extension

WORKING RANGE DIAGRAM

(BOOM DEFLECTION NOT SHOWN)

BOOM & EXTENSION LENGTH IN METRES

HEIGHT FROM GROUND IN METRES

OPERATING RADIUS FROM AXIS OF ROTATION IN METRES

NOTE:
The above heights of lift and boom angles are based on a straight (unladen) boom and
allowance should be made for boom deflections obtained under laden conditions.
TMS 880M

1.716 m
2.644 m

Dimensions are for largest

furnished hook block with anti-
two block activated.

Technical Specification TIL/TMS880M/1019

3
 Lifting Capacities (Metric) 85% Rating
5 Section Boom Duties (in Kilograms)
Main Boom Duties On Outriggers Fully Extended - Full 360° Slew
Radius Main Boom Length in Meters
(in Meters) 12.1 15.5 18.3 21.4 24.4 27.4 30.5 33.5 36.6 39.0 41.4 43.8
3 80000 48200
3.5 66000 46600 44315
4 60000 45085 42025 38165
4.5 54000 43475 38940 36195 35435
5 48000 41455 36215 34060 33540 28210
6 38000 37080 32295 29550 29345 25215
7 31455 31455 29210 26080 24855 22290 21135 20000
8 26535 26535 25965 23605 21475 19820 19095 17980 13300
9 22475 21750 21340 21270 19615 17980 17620 16260 12775 9975 9750
10 17630 17250 17190 17420 16420 15920 14760 11675 9975 9500 9000
12 12160 11830 11780 11990 12150 12660 12425 10925 9975 9500 9000
14 8380 8340 8550 8700 9180 9640 9530 9170 8750 8500
16 5980 5970 6170 6320 6780 7220 7590 7840 7800 7800
18 4230 4430 4570 5020 5450 5810 6050 6260 6450
20 3100 3240 3680 4090 4450 4680 4890 5070
22 2180 2620 3030 3370 3600 3810 3980
24 1740 2150 2500 2730 2930 3100
26 1020 1420 1770 2000 2200 2370
28 810 1150 1380 1580 1750
30 860 1050 1220
32 770
Note: Minimum boom angle 0 degree for 43.8 meter boom length (no load) at over rear only.
WARNING - Do not derrick-up from 0 degree boom angle if boom length is more than 33.5 meter.

10.1m Fixed Offset Extension - 360° 17.1m Tele Offset Extension - 360°
Radius Radius
0° Offset 20° Offset 40° Offset 0° Offset 20° Offset 40° Offset
(in Meters) (in Meters)
3875
12.0 12.0
(75.03)
3875 2280
14.0 14.0
(72.82) (74.68)
3875 3375 2280
16.0 16.0
(70.57) (73.72) (72.72)
3780 3260 2965 2280
18.0 18.0
(68.30) (71.43) (74.01) (70.74)
3450 3005 2840 2280 2040
20.0 20.0
(65.99) (69.11) (71.63) (68.73) (73.73)
3225 2830 2690 2280 2035
22.0 22.0
(63.63) (66.74) (69.20) (66.70) (71.68)
2980 2640 2530 2190 1900 1685
24.0 24.0
(61.23) (64.33) (66.72) (64.63) (69.60) (73.72)
2190 2150 2130 2050 1780 1630
26.0 26.0
TMS 880M

(58.76) (61.85) (64.18) (62.53) (67.48) (71.52)

1570 1500 1500 1500 1500 1500
28.0 28.0
(56.24) (59.31) (61.56) (60.39) (65.32) (69.27)
1000 900 900 900 900 900
30.0 30.0
(53.63) (56.69) (58.85) (58.20) (63.11) (66.96)

NOTE: ( ) boom angles are in degrees for reference only. Boom deflections are not considered.

Technical Specification TIL/TMS880M/1019

4
Note
Weight Reductions for Load Handling Devices
Auxiliary Boom Head 60 kg. 10.1m Boom Extension
Hookblocks and Headache Ball Stowed (Boom Extension) *470 kg.

80 MT 6 Sheaves **650 kg. Erected (Boom Extension) *2195 kg.

40 MT /50 MT **426 kg. 17.1m Boom Extension

15 MT 1 Sheave **418 kg. Stowed (Boom Extension) *725 kg. *Reduction of main boom capacities.
** Refer to rating plate for actual
6.8 MT Headache Ball **140 kg. Erected (Boom Extension) *3680 kg. weight.

Hookblock Capacities and Weights- Tonnes

No of Falls 12 11 10 9 8 7 6 5 4 3 2 1

Permissible Load 80.0 73.5 67.0 60.5 54.0 48.5 42.5 35.5 26.7 19.7 12.7 6.5

Weight of Hook block 0.650 0.650 0.650 0.650 0.650 0.650 0.650 0.650 0.650 0.650 0.418 0.140

Notes for Lifting Capacities

WARNING: THIS CHART IS ONLY A GUIDE. The Notes below 9. 10.1m fixed length and 17.1m tele length boom extensions
are for illustration only and should not be relied upon to may be used for double or single line lifting service.
operate the crane. The individual crane’s load chart, operating
instructions and other instruction plates must be read and 10. Boom Extension Warning : For main boom length greater than
understood prior to operating the crane. 33.8m with 10.1m fixed length and 17.1m tele length boom
extensions in working position, the boom angle mustnot be
1. All rated loads have been tested to meet minimum less than 50°, since loss of stability will occur causing a tipping
requirements of IS: 4573-1982 Specification for Power Driven condition. The boom angle is not restricted for main boom
Mobile Cranes and do not exceed (85% of the tipping load length equal to or less than 33.8m. This warning applies for
on outriggers as well as on rubber) as determined by SAE boom extension erection prurposes also.
J765OCT 80 Crane Stability Test Code.
11. Lifting over-side on rubber is not permitted. Outrigger beams
2. The weight of hook-block, slings and all similarly used load must be fully extended and stabilizers properly set when
handling devices must be added to the weight of the load. rotating superstructure over the side.
When more than minimum required reeving is used the
additional rope weight shall be considered part of the load. 12. Load ratings are based on freely suspended loads. No attempt
shall be made to move a load horizontally on the ground in
3. Capacities appearing above the bold line are based on any direction.
structural strength and tipping should not be relied upon as a
capacity limitation. 13. Do not move the crane with boom extended or jib erected.

4. All capacities are for crane on firm, level surface. It may be 14. Handling of other equipment with the boom is not authorized
necessary to have structural supports under the outrigger except with equipment furnished and installed by TIL Ltd.
floats or tyres to spread the load to a larger bearing surface.
WARNING: Outrigger beams must be fully extended and
5. When either boom length or radius or both are between stabilizers properly set when rotating superstructure over
values listed, the smallest load shown at either the next larger side. Do not rotate superstructure while on rubber.
radius or boom length shall be used.

6. For outrigger operation, all outriggers shall be fully extended

& jacks properly set to raise tyres free of the ground & the slew
plinth becomes horizontal before raising the boom or lifting
1.716 mm

loads.
2.644 m
TMS 880M

7. The machine is equipped with front jack, the front jack cylinder
shall be set along with the four outriggers.

8. Tyres shall be inflated to the recommended pressure. Damaged

tyres are hazardous for safe operation of crane. Dimensions are for largest furnished hook block with
anti-two block activated

Technical Specification TIL/TMS880M/1019

5
 Carrier Specifications

CARRIER Parking - Flick-valve operated, spring actuated pneumatically

8x4 wheel right hand drive, purpose-built, heavy duty released brake on trailing and leading rear axles.
carrier frame of torsion box section with integral front &
FUEL TANK
rear outrigger housing fabricated from high strength steel Capacity - 300 litres
plates and sections.
WHEELS & TYRES
OUTRIGGERS Front Tyres 12.00 x 24-20PR. Rear tyres 12.00 x 20-18PR.
Hydraulically operated outrigger system comprising four Single on front axles and twins on rear axles.
independently controlled hydraulic telescopic horizontal Spare wheel (one) provided for front axle.
beams with vertical jacks for over side & over rear operation.
Plus one vertical hydraulic jack mounted under front of DRIVER’S CAB
carrier to permit 360° lifting duties. Outrigger hydraulic Two man design, steel construction full width cab with
jacks are fitted with positive lock valves. Easy fit outrigger electric fan, interior light, horn, operating windows
feet are provided with stowage facility on carrier. fitted with toughened glass. Two lockable doors, electric
windscreen wiper in front of windscreen. Upholstered and
OUTRIGGER CONTROLS adjustable operator’s seat. Automotive controls include
Located in the superstructure cab on front dash panel steering wheel, pedals for clutch, brake and accelerator.
as well as on both side of the chassis, requires two hand
INSTRUMENTATION
operation. Crane level indicator adjacent to controls.
Air pressure gauge, engine oil pressure gauge, fuel gauge,
ENGINE water temperature gauge, speedometer, voltmeter, tacho-
Volvo TAD852VE hourmeter, warning lights and switches for control.
286 HP (210 kW) @ 2200 RPM
ELECTRICAL EQUIPMENT
Max. Torque: 1237 Nm @ 1200-1600 RPM
24-Volt starting and lighting system includes two combined
Emission : BS III CEV
dipping head lamps, side, rear and stop lamp, flashing
CLUTCH direction indicators.
Dry single-plate air assisted, hydraulically operated.
MISC. STANDARD EQUIPMENT
GEAR BOX Beacon Lights
ZF, Synchromesh, 9 forward & 1 reverse speed obtained via 3 point seat belt in driver’s cab
a single lever control. Boom base light
Front and Rear Tow Hook
DRIVE CONFIGURATION
Mobile charging point in driver’s cabin
8x4
1 no. Fire Extinguisher
AXLES First-Aid box
Front Axle - 2 beam type non-drive steer axles, leaf spring Full Deck Platform
mounted in tandem. Lockable Tool Box
Rear Axle - 2 Heavy duty, fully floating type, twin axle. Air Tool Box with Tool Kit for normal maintenance
operated inter axle differential lock. Mounted on specially MAXIMUM SPEED
designed rocker beam to allow maximum articulation on 49 km/hr.
uneven ground.
GROSS VEHICLE WEIGHT AND AXLE LOADS (approx)
STEERING Front Axles - 19,750 kg
Front axles, mechanical with hydraulic power assist Rear Axles - 30,000 kg
controlled by steering wheel from driver’s cab. GVW - 49,750 kg
TMS 880M

Turning Circle Diameter - 23.8M

WEIGHTS FOR OPTIONAL ITEM (approx.)
BRAKES Auxiliary Hoist : 750 kg
Service - Air operated on all wheels by means of foot 10.1m Fixed Lattice : 800 kg
operated pedal in driver’s cab. 17.1m Tele Lattice : 1200 kg

Technical Specification TIL/TMS880M/1019

6
GA Drawing

TMS 880M

Lattice (Optional)

Dimensions in mm
TMS 880M

Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment and price changes without
notice. The photographs/drawings in this document are just for Illustrative purpose which may include optional equipment and accessories, which can be
provided at an additional cost on request.

Technical Specification TIL/TMS880M/1019

7
TIL Limited
CIN: L74999WB1974PLC041725
Registered & Corporate Office:
1, Taratolla Road, Garden Reach, Kolkata - 700024
Phone: + 91 33 2469 3732-6 / 6497 | 6633 2000 / 2845
Mobile: +91 9831839025 | +91 9831054573
Fax: + 91 33 2469 2143 / 3731
Email: Mhg.Er@tilindia.com | mktg-til@tilindia.com

CHENNAI
TIL Limited
Jhaver Plaza, 7th Floor 1-A Nungambakkam
High Road
Chennai 600 034, Tamil Nadu
Phone: +91 044 6670 3000 / 3010
Mobile: +91 9618562333 | +91 9790973502
Fax: +91 44 2827 9681
Email: chennai.til@tilindia.com

DELHI NCR
Plot 11, Site No.IV
Sahibabad Industrial Area
Ghaziabad 201 010 U.P.
Phone: +91 120 277 8735 / 8736 / 7468
Mobile: +91 9971091610 | 9903842544
Fax: +91 120 277 7467
Email: MHGMarketing.Sahibabad@tilindia.com | mhgcs.Sahibabad@tilindia.com

DELHI
TIL Limited
302 Ansal Bhawan
16, Kasturba Gandhi Marg, New Delhi 110 001
Phone: +91 11 2331 1607 / 8046 / 9248 | 2335 0250 / 0255
Fax: +91 11 2331 3263
Email: til.delhi@tilindia.com

KAMARHATTY
TIL Limited
517, Barrackpore Trunk Road
Kolkata 700 058
Phone: +91 33 2553 1352 / 1882 | 6633 4000
Fax: +91 33 2553 2546 / 5971
Email: MktDept.KMT@tilindia.com | til.kmt@tilindia.com

KHARAGPUR
TIL Limited
Vill. & P.O. Changual, Kharagpur
Dist: Paschim Medinipur 721 301, West Bengal
TIL has a pan-India network of offices with service
Phone: +91 32 2266 1101 engineers located in the close proximity of jobsites.
MUMBAI
TIL Limited
A - 606, A Wing, 6th Floor, Toll Free No:1800 266 1535
215 Atrium, Andheri - Kurla Road,
Andheri (East), Mumbai 400059, Maharashtra www.tilindia.in
Phone: + 91 22 4969 1169
Mobile: +91 8850971609
Email: Mumbai.TIL@tilindia.com | Mumbai.Custsupp@tilindia.com Technical Specification TIL/TMS880M/1019. This cancels Technical Specification TIL/TMS880M/0219

Copyright © 2019 TIL Limited. All Rights Reserved