INSTRUCTION MANUAL
GT1-EVO
VERSION 2.3
Last updated: 21-03-2022
BEFORE YOU START:
Thank you for purchasing this Sim-Lab product! On the following pages, you will find detailed instructions on
assembly. This requires only a set of simple tools and some of your time. Please check the bill of materials before
starting (page 22) and make sure all the parts are delivered.
Note:
Depending on your date of purchase, you may or may not have received a large bag of additional washers. If this
is the case, use one on every M8 bolt to install brackets. This was a temporary solution and will be phased out as
soon as possible and therefore is omitted from this instruction manual.
Inserting Slot-Nuts:
You got excited, finished the build, put the caps on, but forgot to install
one element. Do not worry. It happens to everyone. In this diagram, you
can see how to insert a Slot-Nut directly into the slot from the side.
You can also use one of your smaller Hex wrenches to help wiggle
the Slot-Nut in place.
Breaking tabs:
Sometimes tabs from corner brackets need to be broken off in
order to fit as instructed. Place a flathead screwdriver behind
the tab and tilt upwards.
Always make sure to point away from you while doing so.
To know when to do this, we will show the following
symbol next to the brackets.
Tools needed:
5/6MM - 22 | 25
1350MM Slot-Nut M8
1X 4X
BUILD 2X
P1
A26
33 | 25
500MM Slot-Nut M8
1X 4X
BUILD 2X
P3
A26
44 | 25
Corner M8 X 16
Bracket
8X 16X
A12
A17
500MM
or
20”
55 | 25
Profile 80x40 Corner Bracket Rubber M6 X 20 Slot-Nut M6
End-Cap Cap Feet (A19) (A27)
A19
4X 8X 4X 4X 4X
A11
A27
A13
120MM
or
A14 5”
66 | 25
500MM Corner M8 X 16 Slot-Nut M8
Bracket*
1X 2X 2X 2X
BUILD 2X
A26
P6
A12
A17
77 | 25
Profile 40X40 Corner Bracket M8 X 16 Slot-Nut M8
End-Cap Cap
A17
A13
4X 4X 4X 4X
A15
A26
88 | 25
580MM Corner M8 X 16 Slot-Nut M8
Bracket
A17
1X 2X 2X 2X A12
BUILD 2X
A26
P2
99 | 25
M8 X 16 Slot-Nut M8
4X 4X
A17
A26
430
430MM
or
17”
10
10 | 25
Profile 80X40 Corner Corner Bracket M8 X 16 Slot-Nut M8
End-Cap Bracket Cap
A12
2X 2X 4X 2X 8X
A14
A17
A26
A13
11
11 | 25
500MM Slot-Nut M8
1X 4X
A26
P3
12
12 | 25
Corner Bracket M8 X 16
Cap
2X 2X
A17
A13
13
13 | 25
Corner Corner Bracket M8 X 16
Bracket* Cap
2X 2X 4X
A13
A17
A12
14
14 | 25
Wheel Deck Wheel Deck Wheel Deck M8 X 20 Washer M8 Lock-Nut M8
Pivot Plate Pivot Plate
Left (A9) Right (A10)
1X 1X 1X 4X 8X 4X
A16
A23 A9
A22
A8
A10
15
15 | 25
M8 X 16 Washer M8 Slot-Nut M8
A17
A26
4X 4X 4X
A22
16
16 | 25
200MM Profile 80X40 Corner M8 X 16 Slot-Nut M8
End-Cap Bracket
A14
1X 1X 1X 1X 1X
BUILD 2X
A26
A12
P5
A17
17
17 | 25
Corner Bracket M8 X 16 Slot-Nut M8
Cap
2X 2X 4X
A13
A17
A26
18
18 | 25
Pedal Deck M8 X 16 Washer M8
1X 4X 4X
A22
A7
A17
19
19 | 25
400MM Profile 80X40 Corner M8 X 16 Slot-Nut M8
End-Cap Bracket
1X 1X 2X 2X 2X
A26
A14
A12
A17
P4
20 | 25
20
Corner Bracket M8 X 16
Cap
2X 2X
A13
A17
21
21 | 25
PROFILE KIT
# Part QTY Note
P1 80X40 Length=1350mm 2
P2 80X40 Length=580mm 2
P3 80X40 Length=500mm 3
P4 80X40 Length=400mm 1
P5 80X40 Length=200mm 2
P6 40X40 Length=500mm 2
HARDWARE KIT
A7 Pedal deck 1
A8 Wheel deck plate 1
A9 Wheel deck pivot plate LEFT 1
A10 Wheel deck pivot plate RIGHT 1
A11 Rubber Feet 4
A12 Corner bracket 40x40 28
A13 Corner bracket 40x40 cap 28
A14 Profile 80x40 end-cap 9
A15 Profile 40x40 end-cap 4
A16 Bolt M8 X 20 DIN 912 8 Bag HW 20.D
A17 Bolt M8 X 16 DIN 912 72 Bag HW 20.C
A18 Bolt M8 X 12 DIN 912 4 Bag HW 20.D
A19 Bolt M6 X 20 DIN 912 20 Bag HW 20.D
A20 Bolt M6 X 16 DIN 912 10 Bag HW 20.D
A21 Bolt M5 X 25 DIN 912 12 Bag HW 20.D
A22 Washer M8 DIN 125-A 12 Bag HW 20.D
A23 Lock-Nut M8 DIN 985 8 Bag HW 20.D
A24 Lock-Nut M6 DIN 985 12 Bag HW 20.D
A25 Lock-Nut M5 DIN 985 12 Bag HW 20.D
A26 Slot-Nut M8 75 Bag HW 20.B
A27 Slot-Nut M6 12 Bag HW 20.A
Disclaimer: for some entries on this list, we supply more than required as spare
materials. Don’t worry if you have some leftovers, this is intentional.
22
22 | 25
COMPATIBLE
PEDALS
BJ F1/GT
Heusinkveld Pro Heusinkveld Sprint
VRS DirectForce Pro
Thrustmaster T3PA Logitech GXXX Pedals
(only top row bolts)
23 | 25
23
Fanatec CSP V3
Thrustmaster T-LCM
Fanatec CSL
24 | 25
24
If you still have some questions regarding assembly of this product or about the manual itself,
please refer to our support department. They can be reached at
support@sim-lab.eu
Alternatively, we now have a Discord server where there are quite some experienced Sim-Lab
customers hanging out. They might just help you along if you ask them nicely ;)
www.sim-lab.eu/discord
If you feel like printing this manual, please consider the environment before doing so. For the best
results, make sure you print at 100% scale without borders.
Product page on the Sim-Lab website: Instruction video on YouTube:
25 | 25
25
