2

:: Introduction
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new Kit. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the
illustrations. New parts will be noted on supplementary sheets.
:: KIT Features
• Based on the 9-time R.O.A.R. National Champion short-course race truck platform
• Water-resistant enclosed receiver box
• Three position wheelie bar with optional large wheels
• Lightweight drag race inspired wheels
• Rear Anti-Roll Bar
• Silicone rear diff fluid
• Durable and lightweight aluminum top shaft
• Low center-of-gravity molded composite chassis with hook-and-loop battery straps fit both NiMH and 2/3s LiPo battery packs
• Metric hardware throughout
• 18 precision rubber-sealed ball bearings
• Durable front and rear wide body mounts
• Rear CVA drive shafts for more reliability
• Aluminum 12mm big bore coil-over shock absorbers
• 2.6:1 ratio gearbox with heavy-duty sealed gear differential and externally adjustable V2 slipper clutch
• Rugged steel turnbuckles for adjustable camber and front toe-in
• Adjustable suspension geometry
• Vertical ball ends for roll center adjustments, front and rear
• Many Factory Team options already available!

:: Additional
Your new DR10 Kit comes unassembled and requires the following items • Body and Polycarbonate specific spray paint
for completion (refer to catalog section for suggestions): • Cyanoacrylate glue (CA)(#1597)
• R/C two channel surface frequency radio system • Thread locking compound (#1596)
• AA-size batteries for transmitter (#302 alkaline) • 1:10 scale 2.2” / 3.0” rear tires & 2.2” front tires
• Electronic Speed Control, ESC - See Catalog Listings - See Catalog Listings
• Steering servo - See Catalog Listings
• R/C electric motor - See Catalog Listings
• Pinion gear (48P), size determined by type/wind of motor
• Battery charger (a peak detection charger, or LiPo compatible charger) Tools included:
• 2-3 cell 7.4V-11.1V LiPo or 6-7cell NiMH battery pack • Allen wrenches 1.5mm, 2.0mm
- See Catalog Listings • 12mm Shock Tool
:: Other Helpful Items
• Silicone Shock Fluid (Refer to catalog for complete listings) • Shock Pliers (#1675)
• Silicone Diff Fluid (Refer to catalog for complete listings) • Ride Height Gauge (AE #1449)
• Green Slime shock lube (AE Part #1105) • Body Scissors (AE Part #1737) • FT Body Reamer (#1499)
• FT Hex/Nut Wrenches (AE Part #1519, 1650) • FT Ballcup Wrench (#1579) • FT Universal Tire Balancer (#1498)
• FT Dual Turnbuckle Wrench (#1114) • Calipers or a Precision Ruler • Needle Nose Pliers
• Soldering Iron • Hobby Knife • Wire Cutters
Associated Electrics, Inc. Customer Service
21062 Bake Parkway. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
3
:: Hardware - 1:1 Scale View
Button Head (bhcs) Flat Head (fhcs) Ball Bearings

2x3mm (31509) 2.5x10mm (31530) 3x7x3mm (91475)

2x4mm (31510) 3x8mm (25201)

Aluminum (8545) Aluminum (8553) 5x10x3mm (31734)
Titanium (91592)
2.5x8mm (31521)
3x10mm (25202)
3x5mm (31530) Aluminum (8555) 5x10x4mm (25237)
Titanium (91593)
3x8mm (31532)
Aluminum (8552) 3x12mm (25203)
Titanium (91581) Aluminum (8556) 6x13x5 (91562)
Titanium (91594)
3x10mm (25211)
Aluminum (8554) 3x14mm (89208)
Titanium (91582) Aluminum (8567)
Titanium (91595) 10x15x4 (91563)
3x12mm (89202)
Titanium (91583) 3x16mm (25204)
Titanium (91596)
3x14mm (25187)
Titanium (91584)

3x16mm (89203) Set Screws Ballstuds

Titanium (91585)
3x3mm (25225) HD 6mm (91047)
3x22mm (25189) Titanium HD 6mm (91751)
Titanium (91588) 3x5mm (89219)
HD 8mm (91048)
3x24mm (89204) Titanium HD 8mm (91752)
Titanium (91589)
HD 10mm (91049)
3x26mm (89205) Shims and Washers
Titanium HD 10mm (91753)

3x30mm (91478) Servo Mount Washer (7337)

(.250 x .125 x .815)
Nuts (lock/plain)
Cap Head (shcs) FT Ballstud Washer, Aluminum
(0.5mm) (31381) M3 Nut (91477)
2x6mm (7186) M3 Alum. Locknut, Blue (31550)
FT Ballstud Washer, Aluminum M3 Locknut, Black (25215
2.5x14mm (71032) (1mm) (31382)
M3 Locknut w/Flange (25612)
3x24mm (89225) FT Ballstud Washer, Aluminum FT 3mm Locknuts, Blue(25392)
(2mm) (31383)
3x45mm (89279) M4 Serrated w/Flange (91738)
FT M4 Locknuts w/Flange,
Blue (31551)
Clips
E-clip 1/8 (6299)

Notes:
 4
:: Table of Contents
1....................Cover 11 - 12.........Rear Hub and CVA Build - Bag 8

2....................Introduction 12 - 13........ Turnbuckles Build - Bag 9

3....................1:1 Hardware “Fold Out” 13 - 14.........Shocks Build - Bag 10

4....................Table of Contents 15.................Anti-Roll Bar Build - Bag 11

5....................Front Top Plate and 16.................Servo and Motor Install

Steering Build - Bag 1 - Bag 12

6....................Steering Blocks Build - Bag 2 17..................Nerf Bars, Receiver, and

Battery Install - Bag 13

6 - 7...............Front Suspension Build - Bag 3

18.................Wheelie Bar Build - Bag 14

7 - 8..............Rear Suspension Build - Bag 4

19 - 20....... Tuning Tips

8 - 9..............Gear Differential Build - Bag 5

21 - 29........Catalog

9 - 11............Gearbox Build - Bag 6

30................ Back Cover

11..................Rear Body Mounts Build - Bag 7

:: Notes

This symbol indicates a special

! note or instruction in the manual.

There is a 1:1 hardware foldout page in the

front of the manual. To check the size of a part,
This symbol indicates a Racers Tip. line up your hardare with the correct drawing
until you find the exact size. Each part in the
foldout has a number assigned to it for ordering
replacement parts.

Associated Electrics, Inc. Customer Service

21062 Bake Parkway. Tel: 949.544.7500
Lake Forest, CA 92630 Fax: 949.544.7501
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebook.com/TeamAssociated/
6/20 5
:: Front Top Plate and Steering Build - Bag 1 - Step 1
91475 x4 91047
91047 x2
3x7x3 Heavy-duty
Heavy-duty
Ball Bearing Ballstud,
Ballstud, 91391
6mm Steering 6mm
Bellcrank
91391
Brace
Steering
Rack

!
Note orientation
89202 x2
M3 x 12mm
of steering rack.
91391 x2 BHCS
Steering
Rack Crush
Tube
! Do not overtighten steering bolts. Make sure
there is free movement in the steering rack.

:: Front Top Plate and Steering Build - Bag 1 - Step 2

!
Note orientation
of the brace.

91475 x4 91358
3x7x3 Chassis
Ball Bearing Brace Set
(Top Plate)

91391
Steering
25189 x2 Bellcrank
M3 x 22mm Brace
BHCS

:: Front Top Plate and Steering Build - Bag 1 - Step 3

25202 x2
71024
M3 x 10mm
Chassis
FHCS

91359
Bulkhead

25204 x2
M3 x 16mm
FHCS
 6
:: Steering Blocks Build - Bag 2 - Step 1
91047
31530 Heavy-duty 91048
96
M3 x 5mm #15 lock Ballstud, 91402 x2
e a d Heavy-duty
thr
BHCS 6mm Ballstud, Caster
8mm Block
91417 Bushing
Steering
25237 x2 Block
5 x 10 x 4
Bearing 91417
Caster
Block
25215
M3 Locknut, 71127
black Front 89202 x2
Axles M3 x 12mm
Build 2 (1 left, 1 right) BHCS

:: Front Suspension Build - Bag 3 - Step 1

31509 x2
71068 M2 x 3mm
Front Arms BHCS

6
59 ck
#1 lo
r e ad
th

91394
Hinge Pin
(front, outer)

31510 x2
M2 x 4mm
BHCS
25211 x2 71049 91394
M3 x 10mm Front Hinge Hinge Pin
Build 2 (1 left, 1 right) BHCS Pin Brace (front, Inner)

:: Front Suspension Build - Bag 3 - Step 2

31383 x2 91049 x2
Heavy-duty 71066 91477 x2
FT Ballstud
Ballstud, 10mm Front Body M3 Nut
Washer,
Mount (Black)
Aluminum
(2mm)

25201
89205 x2 M3 x 8mm
71003
M3 x 26mm FHCS
Front Shock
BHCS
Tower
 7
:: Front Suspension Build - Bag 3 - Step 3

Reakt
71066 x2
Body
Front Body Trim
Post Post

71032 x2
M2.5 x 14mm
SHCS
89202 x4
M3 x 12mm
BHCS

:: Rear Suspension Build - Bag 4 - Step 1

31521
M2.5 x 8mm 71068 x2
BHCS Rear Arms
91359
C Mount

91359
D Mount

91394
Hinge Pin
(rear, Inner)
91359 25187 x2
Rear Chassis M3 x 14mm
Plate BHCS

:: Rear Suspension Build - Bag 4 - Step 2

25211 x2
91049 x2 M3 x 10mm
Heavy-duty BHCS 91358
Ballstud, 10mm Rear Chassis
Brace

31383 x2
FT Ballstud
Washer,
Aluminum
(2mm)

25203 x2
89208 x2 M3 x 12mm
M3 x 14mm FHCS
FHCS
 8
Front Suspension
:: Rear Shock Tower and -Bumper
Build Bag 4 -Build - Bag C - Step 3
Step 3
25187 x2 25211 x2
M3 x 14mm M3 x 10mm
89204 x2 BHCS BHCS
M3 x 24mm
BHCS

91477 x2
M3 Nut
(Black)
71003
Rear Shock
Tower

:: Rear
Gear Shock
Diff Build
Tower- Bag
and5Bumper
- Step 1Build - Bag D - DD - Step 1
91463 x2
Gear Diff 91463 x4
Washer Gear Diff
91466
Planet
Gear Diff 91463 Washer
Gear Gear Diff
Sun Gear 91463 x4
91463 91463 Gear Diff
Gear Diff Gear Diff Planet
91463
O-Ring Outdrive Gear
Gear Diff
(Small) Pin
O-Ring
(Large)
91463 x2
Gear Diff
91465
Cross Pin
Gear Diff
Outdrive

:: Gear
Rear Shock
Diff Build
Tower- Bag
and5Bumper
- Step 2Build - Bag D - DD - Step 2
91463 x2
Gear Diff
91466 Washer
Gear Diff
Gear
91463
Gear Diff
91463
91463 Sun Gear 91463
Gear Diff
Gear Diff O-Ring Gear Diff
O-Ring (Small) Outdrive
(Large) Pin

91465
Gear Diff
Outdrive
 9
:: Gear Diff Build - Bag 5 - Step
Step 3

31350 x4
!
id
flu ,
ff
Di 546
# 00k
3
M2.5 x 10mm
5
FHCS
* Fill diffs to this level

91463
Gear Diff
Gasket
!
* Ensure free outdrive
rotation before
installation!

:: Gearbox Build - Bag 6 - Step 1

91430
Gearbox 91466
(right & left) Idler Gear

91563 x2
10 x 15 x 4,
Bearing
91132
25237 x2 Idler Gear
5 x 10 x 4, Shaft
Bearing
25237 x2
5 x 10 x 4,
Bearing

:: Gearbox Build - Bag 6 - Step 2

Add a drop of Diff
Lube (#5463) to

!
the teeth of the diff 31532 x2
gear, idler gears, d M3 x 8mm
ui
and top shaft. fl ,
i ff 463
D 5 0k
# 0
BHCS
5

91606
Top Shaft
Aluminum

89203 x5 91431
M3 x 16mm Motor
BHCS Guard
10
:: Gearbox Build - Bag 6 - Step 3
91478 x2 71038 x2
M3 x 30mm Body Mount
FHCS Brace
(Left & Right)

89225
M3 x 24mm
SHCS

91428
71070 x2 25215 Motor Plate, 25202 x3
Wheelie Bar M3 Blue M3 x 10mm
Mount Locknuts FHCS

:: Gearbox Build - Bag 6 - Step 4

9611 x2 9739
Slipper Slipper
Pad Spring

7485 x2
FT V2 91423 91738
Slipper Hub 9654 Slipper M4 Locknut,
Spur Gear Spring with flange
87T, 48P Adapter and knurl

:: Gearbox Build - Bag 6 - Step 5

!
The Locknut should
be flush with the
top shaft when
installed.

!
See page 23 for gear
mesh, and slipper clutch
setting instructions!
 11
:: Gearbox Build - Bag 6 - Step 6

25211 x2
M3 x 10mm
BHCS

25203 x2
M3 x 12mm
FHCS

:: Gearbox Build - Bag 7 - Step 1 :: Rear Body Mount Build - Bag 7 - Step 2
25202 x4 71066 x2
25204 x2 M3 x 10mm Rear Body
M3 x 16mm FHCS Pivot
FHCS
71066 x2
71038 Rear
Rear Body Body Post
Mount

REAKT
Body

71032 x4
M2.5 x 14mm
SHCS

:: Rear Hub and CVA Build - Bag 8 - Step 1

91563
10 x 15 x 4 91438
Bearing 91418 CVA
Rear Hub Coupler

#6588
e
greas
black
91439
CVA Bone,
65mm

91048 91562
Heavy-duty 6 x 13 x 5 91438
Ballstud, 8mm Bearing 71019 CVA
HD Pin
CVA Axle
Build x2 (right and left side) Build x2 (right and left side)
12
:: Rear Hub and CVA Build - Bag 8 - Step 2

91436
CVA Wheel
Hex Pin

91418
31510
Wheel 91394
M2 x 4mm
Hex (rear) Hinge Pin
BHCS
Build x2 (right and left side) (rear, outer)

:: Turnbuckles Build - Bag 9 - Step 1

91469 91469
91723
Ball Cup Ball Cup
Turnbuckles,
3x48mm

!
Orient the notch Racers Tip:
Steering Turnbuckle
27.00mm
to the left throughout the Use black grease
car. It indicates which end (#6588) on the
has the left hand threads! threads of the
turnbuckles for
easier ball cup
installation! Build x2 (right and left side)

:: Turnbuckles Build - Bag 9 - Step 2

91469 91469
91723
Ball Cup Ball Cup
Turnbuckles,
3x48mm

!
Orient the notch
Racers Tip:
Front Camber Turnbuckle
23.00mm
Use black grease
to the left throughout the
(#6588) on the
car. It indicates which end
threads of the
has the left hand threads!
turnbuckles for
easier ball cup
installation! Build x2 (right and left side)
 13
:: Turnbuckles Build - Bag 9 - Step 3

91469 91469
91723
Ball Cup Ball Cup
Turnbuckles,
3x48mm

!
Orient the notch Racers Tip:
Rear Camber Turnbuckle
23.50mm
to the left throughout the Use black grease
car. It indicates which end (#6588) on the
has the left hand threads! threads of the
turnbuckles for
easier ball cup
installation! Build x2 (right and left side)

:: Shocks Build - Bag 10 - Step 1

91444
6299 6299
12mm
1/8 E-Clip 1/8 E-Clip
Shock Piston

91489
3 x 27.5
Shock Shaft
(front, rear)
Racers Tip:

Use a marker over the

numbers on the pistons to
make them easily visible!

:: Shocks Build - Bag 10 - Step 2

71051 91491
Shock Body
12 x 27.5mm ! Shock Cap
O-Ring
(front, rear) Lightly rub shock oil
on the o-ring before
installation! 5
10 me
#1 sli
n
31327 gr
e e

Shock
Bottom Cap
O-Ring Racers Tip:

91444 #1105
Coating the o-rings
91469
green slime
Shock with green slime Shock
Internals (#1105) helps seal eyelet
& reduce o-ring
swell! Green slime 91469
91454 5407 x2 not included in kit!
Shock O-Ring Shock
Bottom Cap Pivot Ball
14
:: Shocks Build - Bag 10 - Step 3
k
flu
id
2
Sh
oc 91454 Shock Bleeding Steps:
oc 42 #5 k flu
h
S #5 42 id
2 Shock Cap 1. Pull shock shaft down.
(Molded) 2. Fill shock body 3/4 full with silicone
fluid. Free
Front/Rear 3. Slowly move the shock shaft up and
down to remove air from under piston.
Length
Shock: 30wt 4. Wait for bubbles to come to surface.
5. Fill shock body to top with silicone fluid.
6. Place a drop of oil in the cap and on Stroke
cap threads.
7. Install cap and tighten completely.
8. Slowly compress shaft all the way to
the top. If there is pressure at the top
of the stroke, there is too much oil or
air. You must bleed it out.
9. Slowly pull shaft out.
10. Unscrew the cap 3/4 turn and tilt the Stroke:
shock at a slight angle.
11. Slowly compress the shaft to push 26.0mm
out excess oil and air. You should see
bubbles coming out from under the
cap.
12. With the shaft compressed, tighten
the cap and re-check for pressure at Free Length:
the top of the stroke. If there is still
pressure, repeat steps 9 thru11.
86.25mm
Step 1-3 Step 3-4 Step 5-6 Step 7 Step 9-10

:: Shocks Build - Bag 10 - Step 4

71054
Pre Load
Spacers

71054
Spring Pre-Load
Collar Spacers
1mm
2mm
3mm 91454
91636 Spring
5mm
12mm Shock Cup
Front Rear
Spring (54mm),
Shocks Shocks
White (4.10lb) 5mm x1 3mm x2
2mm x1

Build x2 front and x2 rear shocks

:: Shocks Build - Bag 10 - Step 5

91444 25612

! Shock
Bushing 91444
M3 Locknut,
with flange
Use outside Shock (black)
hole in
front arm!
Bushing

25612 89202
M3 Locknut, M3 x 12mm
with flange BHCS
(black)

25189
!
Use outside
M3 x 22mm hole in
BHCS rear arm!
Build x2 (right and left side) Build x2 (right and left side)
 15
:: Anti-Roll Bar Build - Bag 11 - Step 1
71086 BUILD X2: Install X2:
6 x 12.5mm Anti-Roll Bar Links Anti-Roll Bar Links
Rod End

71091
3x28mm
Turnbuckle 15.00mm

71086
4.3 x 12.5mm
Rod End

:: Anti-Roll Bar Build - Bag 11 - Step 2

Anti-Roll Bar
Ball End
81150 x2
Anti-Roll
Bar Pivot 71086 x2
Anti-Roll
1mm
Bar Mount

25225 x2
71091
M3 x 3mm
Anti-Roll
Set Screw
Bar, Rear
7186 x2
M2 x 6mm
SHCS

:: Anti-Roll Bar Build - Bag 11 - Step 3

71086 x2
Anti-Roll Bar
Mount Cap

7186 x4
M2 x 6mm
SHCS

89219 x2
M3 x 5mm
Set Screw
Do not overtighten the set

! screws. Anti-Roll bar should

pivot freely.
16
:: Servo and Motor Install - Bag 12 - Step 1
Align the servo horn 90 degrees.
91047
!
Adjust steering trim once vehicle is
Heavy-duty complete.
Ballstud, 6mm

91469
Steering Servo
71047 25201 Link *Not
Servo M3 x 8mm Included
Saver FHCS

:: Servo and Motor Install - Bag 12 - Step 2

91391 x2
Servo
Mount

31532 x4
M3 x 8mm 7337 x4 25201 x2
BHCS Gold M3 x 8mm
Washer FHCS

:: Servo and Motor Install - Bag 12 - Step 3

Motor 31530 x2
*Not M3 x 5mm
Included 25225 BHCS
1336 M3 x 3mm
Pinion Gear, Set Screw

! 18T, 48P
7337 x2 31532 x2 91431 71023
See page 19 for
.250x.125x.015 M3 x 8mm Gear Belt Cover
gear mesh setting
Washer BHCS Cover Cap
instructions!
 17
:: Nerf Bars, Receiver, and Battery Install - Bag 13 - Step 1
71023
Receiver Box

!
Grommet

* Install the ESC wires

and the Servo wires
into the wire grommet
before installing the
grommet into the
receiver box!

71023
Wire * Receiver grommet

!
plug can be removed if
Grommet you use a personal
Plug transponder!

:: Nerf Bars, Receiver, and Battery Install - Bag 13 - Step 2

6727 Receiver 6338 25225
Servo Tape *Not Antenna M3 x 3mm
71023 Included Tube & Cap Set Screw
Receiver
25211 x2
Box Seal
M3 x 10mm
71023
BHCS
Receiver Box
Plug and
Grommet 71026
Receiver
Box Lid
25211
M3 x 10mm
BHCS
71026
Receiver
Box

:: Nerf Bars, Receiver, and Battery Install - Bag 13 - Step 3

Battery
71050 x2 not included!
Hook and ESC 71048
Loop Straps *Not Battery
Included Foam Spacer

25211 x4
M3 x 10mm
BHCS

6727
71067
Servo Tape
Nerf Bar
18
:: Front Bumper and Wheelie Bar Build - Bag 14 - Step 1
71067 25203 x2
Front M3 x 12mm
Bumper FHCS
Brace

71067
Front
Bumper

89202 x2 25204 x2
M3 x 12mm M3 x 16mm
BHCS FHCS

:: Front Bumper and Wheelie Bar Build - Bag 14 - Step 2

71071
Wheelie
Bar Arm
(Left)

25215
M3 Set the wheelie bar
Locknut 31734 x2 higher for more
M5x10x3mm wheelies, lower for
Bearing less wheelies!

71070 71070
Wheelie 22mm
Wheelie
Bar Flange Bar Wheel
Shaft (22mm)
89203
M3 x 16mm 26mm
BHCS Build x2 (right and left side)

:: Front Bumper and Wheelie Bar Build - Bag 14 - Step 3

89279 x2
M3 x 45mm
SHCS

25215 x2
M3
Locknuts
71071
Wheelie 89202 x4
Bar Cross M3 x 12mm
Member BHCS
 19
:: Tuning Tips
Painting:
Your Kit requires a clear polycarbonate body. You will need to prep the body before you can paint it.
Wash the INSIDE thoroughly with warm water and liquid detergent (do not use any detergents with scents or added
hand lotion ingredients!). Dry the body using a clean, soft, lint-free cloth. Use the supplied window masks to cover the
windows from the INSIDE of the body (RC cars get painted on the inside). Using high quality masking tape, apply tape
to the inside of the body to create a design. Spray (use either rattle can or airbrush) the paint on the inside of the body
(preferably dark colors first, lighter colors last). NOTE: ONLY use paint that is recommended for (polycarbonate)
plastics. If you do not, you can destroy the body! After the paint has completely dried (usually after 24 hours), cut the
body along the trim lines. Make sure to drill or use a body reamer to make the holes for the antenna if needed!

Tips for Beginners:

Before making any changes to the standard setup, make sure you can get down the drag strip without crashing.
Changes to your vehicle will not be beneficial if you can’t stay on track. Your goal is consistent passes.

Once you can make consistent passes, start tuning your vehicle. Make only ONE adjustment at a time, testing it before
making another change. If the result of your adjustment is a faster run, mark the change. If your adjustment results in a
slower run, revert back to the previous setup and try another change.

Peridicaly check all moving suspension parts. Suspension components must be kept clean and move freely without
binding to prevent poor and/or inconsistent handling.

Motor Gearing:
Proper motor gearing will result in maximum performance and run time while reducing the chance of overheating and
premature motor failure. The gear ratio chart lists recommended starting gear ratios for the most widely used
motor types. Gear ratios will vary depending upon motor brand, wind, and electronic speed control. Consult your
motor and electronic speed control manufacturers for more information.
Team Associated is not responsible for motor damage due to improper gearing.

Gear Ratio Chart (Internal Gear Ratio 2.60:1)

Motor Pinion Spur Final Drive Ratio
8.5 Reedy Sonic Brushless *18 *87 12.57:1

7.5 Reedy Sonic Brushless *17 *87 13.31:1

6.5 Reedy Sonic Brushless *16 *87 14.14:1

3300kV Brushless 18 87 12.57:1

* Optional spur gear / pinion used

Set The Gear Mesh:

You should be able to rock the spur gear back and forth in the teeth of the pinion gear without making the pinion gear
move. If the spur gear mesh is tight, then loosen the #31532 screws and move the motor away, then try again.
A gear mesh that is too tight or too loose will reduce power and damage the gear teeth.

Anti-Roll Bars:
The anti-roll bar kit (also called the “swaybar”) allows you to add roll resistance to the rear end with
minimal effect on handling over bumps and jumps. It is an especially helpful tuning item on high-grip tracks.
20
:: Tuning Tips (cont.)
Slipper Clutch:
The assembly instructions give you a base setting for your clutch. Turn the nut on the shaft so that the end of the top
shaft is flush with the nut. At the track, tighten or loosen the nut in 1/8 turn increments until you hear a faint slipping
sound for 1-2 feet on takeoffs. Another popular way to set the clutch is to hold both rear tires firmly in place and apply
short bursts of throttle. If the clutch is properly set, the front tires should lift slightly up off the surface.

Ride Height:
Ride height is the distance from the ground to the bottom of the chassis.
!
The standard front ride height setting is with the front arms level *Front arms inner
(reffered to as “arms level”) or 30mm (Ride Height Gauge #1449). and outer hinge pins
Check the ride height by lifting up the entire car about 8-12 inches off the should be in a
bench and drop it. After the suspension “settles” into place, measure imaginary horizontal
ride height (Ride Height Gauge #1449). Add or Remove pre-load spac- line when ride height
ers as necessary so that the left & right arms appear to be level. is set

The rear ride height setting you should use most often is with the
outdrive, driveshaft, and axles all on the same imaginary horizontal line !
(reffered to as “bones level”) or 28mm (Ride Height Gauge#1449). *CVA bones should
Check the ride height by lifting up the entire car about 8-12 inches off the be in a straight line
bench and drop it. After the suspension “settles” into place, measure when ride height is
ride height (Ride Height Gauge #1449). Add or Remove pre-load spac- set at “CVA bones
ers as necessary so that the left & right driveshafts appear to be level. level”

Front Camber:

!
Camber describes the angle at which the tire and wheel rides when
looked at from the front. Negative camber means that the tire leans
inward at the top. A good starting camber setting is -1°. Positive camber,
where the top of the tire is leaning out, is not recommended. *Testing camber
Optional #1719 camber gauge can be used to more accurately set camber. with camber gauge

Rear Camber:
Camber describes the angle at which the tire and wheel rides when looked at from the back. Negative camber means
that the tire leans inward at the top. A good starting camber setting is -1°. Adding a small amount of positive camber,
where the top of the tire is leaning out, will tend to improve straight-line acceleration on loose tracks.
Optional #1719 camber gauge can be used to more accurately set camber.

Front Camber Links:

Changing the length of the camber link is considered a bigger step than
adjusting the ball end height on the tower. Shortening the camber link
(or lowering the ball end) will give the front end less roll and quicken steering
!
*Raise or lower the
response. Lengthening the camber link (or raising the ball end) will give the
front more roll and slower steering response. Longer camber links are ball end by adding
typically used on high grip tracks and shorter links tend to work better on or subtracting
medium-grip loose tracks. washers here

Rear Camber Link:

Changing the length of the camber link is considered a bigger step than adjusting
the ball end height on the rear chassis brace. Shortening the camber link
(or lowering the ball end) will give the rear end less roll and the car will tend to
!
*Raise or lower
accelerate or “square up” better. Lengthening the camber link (or raising the ball
end) will give the rear more roll and more cornering grip. Longer camber links are the ball end by
typically used on high grip tracks, while shorter links tend to work better on adding or
medium grip loose tracks. The kit setting is the best compromise of cornering grip subtracting
and acceleration. washers here

Ackermann:
Ackermann is the angle difference between the front wheels when they are turned to steer the car. For minimal tire
slip, it is standard for the inside wheel to steer to a greater angle than the outside wheel. The DR10 allows ackermann
adjustments by changing the washer thickness used behind the steering rack ballstuds. The kit setup uses 2mm
washers and is most common for racing conditions. If corner entry steering is too aggressive, try increasing the
ackermann by removing shims from behind the steering rack ballstuds. Increasing the ackermann will increase the
angle difference of the front wheels when steered, resulting in a more stable car on corner entry.
 21
:: Shocks :: Shock Springs
5407 Red O-Rings 8 91635 12mm Front Spring (54mm) GRN 3.75 2
6299 E-Clip 12 91636 12mm Front Spring (54mm) WHT 4.10 2
31327 FT VCS3 Shock Bottom Caps 2 91637 12mm Front Spring (54mm) GRY 4.45 2
71051 Shock Body 12 x 27.5mm 2
71054 Spring Clips and Retainer 1
91444 Shock Accessories Set 1
91454 Shock Caps and Spring Cups 4 ea.
91469 Shock Pivot Ball and Rod End 4
91489 27.5 x 3MM Shock Shaft 2
91491 12MM V2 Shock Rebuild Kit 1

:: Shock Fluid
5420 10 Weight Silicone Shock Fluid 2oz.
5421 20 Weight Silicone Shock Fluid 2oz.
5422 30 Weight Silicone Shock Fluid 2oz.
5423 40 Weight Silicone Shock Fluid 2oz.
91454 5424 22.5 Weight Silicone Shock Fluid 2oz.
5425 80 Weight Silicone Shock Fluid 2oz.
91491 6299 5426 27.5 Weight Silicone Shock Fluid 2oz.
71054 5427 15 Weight Silicone Shock Fluid 2oz.
91444 5428 25 Weight Silicone Shock Fluid 2oz.
5429 35 Weight Silicone Shock Fluid 2oz.
6299 71054 5430 45 Weight Silicone Shock Fluid 2oz.
71051 5431 55 Weight Silicone Shock Fluid 2oz.
5432 32.5 Weight Silicone Shock Fluid 2oz.
5433 37.5 Weight Silicone Shock Fluid 2oz.
71054
5434 42.5 Weight Silicone Shock Fluid 2oz.
91489 5435 50 Weight Silicone Shock Fluid 2oz.
5436 60 Weight Silicone Shock Fluid 2oz.
91454 5437 70 Weight Silicone Shock Fluid 2oz.
5438 47.5 Weight Silicone Shock Fluid 2oz.
5407
91491

5407 91469
:: Lubes & Adhesives / Misc.
31327 91469 1105 FT Green Slime Shock Lube 1
1596 FT Locking Adhesive 1
91454
1597 FT Tire Adhesive 1
6588 Black Grease - 4cc 1
6591 Diff Lube - 4cc 1
6636 Silicone Grease - 4cc 1
1596
6727 Servo Tape 2

:: Gear Differential
31350 M2.5 x 10 FHCS 6
91463 Gear Diff Rebuild 1
91465 Gear Diff Outdrives, B5 2 91463
91463
91466 Diff and Idler Gears 1
31350 91466
91465 91466

:: Differential Fluids
91463
5444 Silicone Diff Fluid 4,000CST 1 91463
5446 Silicone Diff Fluid 6,000CST 1 91463
5447 Silicone Diff Fluid 15,000CST 1
5448 Silicone Diff Fluid 80,000CST 1 31350
5451 Silicone Diff Fluid 2,000CST 1
5452 Silicone Diff Fluid 3,000CST 1 91466
5453 Silicone Diff Fluid 5,000CST 1
5454 Silicone Diff Fluid 7,000CST 1
5455 Silicone Diff Fluid 10,000CST 1
5456 Silicone Diff Fluid 20,000CST 1 91463
5457 Silicone Diff Fluid 30,000CST 1 91463
5458 Silicone Diff Fluid 60,000CST 1
5459 Silicone Diff Fluid 100,000CST 1
5461 Silicone Diff Fluid 200,000CST 1
5463 Silicone Diff Fluid 500,000CST 1
5464 Silicone Diff Fluid 1,000,000CST 1 91463 91465
22
:: Transmission
7337 .250x.125x.015” Washer 10
25202 M3 x 10mm FHCS 10 31532
25203 M3 x 12mm FHCS 10
7337
25211 M3 x 10mm BHCS 10 31532
25237 Bearing, 5 x 10 x 4 2 25202
31532 M3 x 8mm BHCS 10 91428
89203 M3 x 16mm BHC 10
91132 4x4 Idler Gear Shaft 1
91428 Motor Plate (Blue), B5 1
91430 Gearbox Pr. 7337 25237
91431 Gear Cover / Motor Guard 1 91431
91466 Diff and Idler Gear 1
91563 FT Bearing, 10 x 15 x 4 4 25202 91606
91606 Aluminum Top Shaft V2 1

25237

25211
25203
91563
91430 91466

91132
91563

25211
89203

91430

:: Slipper Clutch
7485 FT V2 Slipper Hubs 2
9611 Slipper Pad 2 9654
9648 69T 48P Spur Gear 1 7485
9649 72T 48P Spur Gear 1
9650 75T 48P Spur Gear 1
9651 81T 48P Spur Gear 1
9652 78T 48P Spur Gear 1 7485 91423
9653 84T 48P Spur Gear 1
9654 87T 48P Spur Gear (Kit) 1
9739 Slipper Spring 1
91431
31530 M3 x 5 BHCS 10 9611
71023 Belt Cover Cap 2
91423 Slipper Spring Adapter 2
91431 Gear Cover (Black) 1
9611 31530
91738 M4 Serrated Nuts, Black 8
9739
91738
71023

31530

:: Pinion Gears
1335 17T 48P Aluminum Pinion Gear 1 1349 31T 48P Aluminum Pinion Gear 1
1336 18T 48P Aluminum Pinion Gear 1 1350 32T 48P Aluminum Pinion Gear 1
1337 19T 48P Aluminum Pinion Gear 1 1351 33T 48P Aluminum Pinion Gear 1
1338 20T 48P Aluminum Pinion Gear 1 1352 34T 48P Aluminum Pinion Gear 1
1339 21T 48P Aluminum Pinion Gear 1 25225 M3 x 3mm Set Screw 20
1340 22T 48P Aluminum Pinion Gear 1
1341 23T 48P Aluminum Pinion Gear 1
1342 24T 48P Aluminum Pinion Gear 1
1343 25T 48P Aluminum Pinion Gear 1
1344 26T 48P Aluminum Pinion Gear 1
1345 27T 48P Aluminum Pinion Gear 1
1346 28T 48P Aluminum Pinion Gear 1
1347 29T 48P Aluminum Pinion Gear 1
1348 30T 48P Aluminum Pinion Gear 1
 23
:: Optional Ball Differential
6573 Diff Thrust Washer & Bolt 2
6575 31400
6574 Precision Diff Thrust Balls, 5/64” 6
6575 Locking T-Nut, Diff Thrust Bolt, & Cover 1 6582
6581 3/32” Carbide Diff Balls 14 7666
6582 Diff Thrust Spring 1
7666 Diff Drive Rings, 2.60:1 2 91420
7677 Ball Diff Rebuild Kit 1
31400 Bearing, 5 x 8mm 2
91420
91419 Diff Gear, B5 1
91420 Ball Diff Outdrive, B5 1 ea.
7666
6573
6574
31400
6573

6581
6575

91419
6575

:: Turnbuckles and Servo Mounts

7337 .250 x .125 x .015” Washer 4
25201 M3 x 8MM FHCS 10 91469
31532 M3 x 8 BHCS 10
71047 Servo Saver 1
91047
91047 Heavy-duty Ballstud, 6mm 10
91391 Servo Mount and Steering Rack 1
91469 Ball Cups and Steering Link Set 1
91723 3x48mm Turnbuckles 2 91391

7337

91723 91469

31532

71047
25201
25201

:: Front Bulkhead / Steering

25189 M3 x 22mm BHCS 10 91475
91391
25202 M3 x 10mm FHCS 10
89202 M3 x 12mm BHCS 10 91475
91047 Heavy-duty Ballstud, 6mm 10 91391 91391
91358 Top Plate 1
91391 Steering Set, B5 1 91047 91047
91475
91475 3x7x3 Ball Bearing 8

91475 91391
91047
25202
91475 91391

25202 89202 91475

91391

91358

25189
24
Steering
:: FrontBlock,
Arm Hex
25189 M3 x 22mm BHCS 10
25215 M3 Locknut, Black 20
25237 Bearing, 5 x 10 x 4 2 91417
31510 M2 x 4mm BHCS 10 89202
31530 M3 x 5mm BHCS 10
71068 Suspension Arm Set 1
71127 Front Axle 2
89202 M3 x 12mm BHCS 10 91048
91047 Heavy-duty Ballstud, 6mm 10 91047
25237
91048 Heavy-duty Ballstud, 8mm 10
91394 Hinge Pin Set, B5 1 31530
91402 Caster Block Bushing, B5 4
91417 Caster and Steering Blocks Pr. 25237
91738 M4 Serrated Nuts, Black 8
91402
89202

91417 71127

25215

91738
91394

31510

25189

71068

31510
91394

:: Rear Arm
31510 M2 x 4mm BHCS 10
71019 RC10T5M HD CVA Axle 2
71068 Suspension Arm Set 1
89202 M3 x 12mm BHCS 10
91048 Heavy-duty Ballstud, 8mm 10
91394 Hinge Pin Set, B5 1 91438
91418 Rear Hubs and Wheel Hexes Pr.
91436 CVA/Wheel Hex Pin, B5 4
91438 CVA Rebuild Kit, B5 1 91439
91439 Rear CVA Bones, 65mm 2 71019 91048
91562 6x13x5 Ball Bearing 2
91563 10x15x4 Ball Bearing 2
91738 M4 Serrated Nuts, Black 8 91438
91418

91563
91562

91418

91436

71068 91738

89202

91394
31510
 25
:: Battery Strap
71048 Battery Foam 1
71050 Hook and Loop Straps 2

71050

71050

71048

:: Front Bumper
25203 M3 x 12mm FHCS 10
25204 M3 x 16mm FHCS 10 25203
71067 Front Bumper and Nerf Bars 1
89202 M3 x 12mm BHCS 10 71067 25203
71067

89202

89202

25204

25204

:: Wheelie Bar
25215 M3 Locknuts, Black 10 89202
31734 M5x10x3mm Bearings 4 25215
71070 Wheelie Bar Mount and Wheels 1 89202
71070
71071 Wheelie Bar Set 1
71070
89202 M3x12mm BHCS 10 25215
89203 M3x16mm BHCS 10 31734
89225 M3x24mm SHCS 10 89203
89279 M3x45mm SHCS 10 25215 31734 89203
71071 31734
71071
25215 71070
31734
25215
71070
71070

71070
89202
71071 89202

89279
89279 89225
26
:: Front Shock Tower
21173 Small Body Clips 12
25201 M3 x 8mm FHCS 20
25612 M3 Locknut, with flange 20
31383 Ballstud Washer, 5.5 x 2mm, 10
Blue Aluminum
71003 Pro SC10 Shock Tower Set 1 91477 91444
71032 M2.5 x 14MM SHCS 10
71066 Body Posts and Body Mount 1
89202 M3 x 12mm BHCS 10 25612
71003
89205 M3 x 26mm BHCS 10
91049 Heavy-Duty Ballstud, 10mm 10 25612
91444 Shock Rebuild Kit 1 91049
91477 M3 Nut, Black 6
31383

21173 71066 25201 91444

89202 91049 91477

31383
89202

21173
71066

71032

71066

71032

:: Rear Shock Tower

21173 Small Body Clips 12
25187 M3 x 14mm BHCS 10 21173
71066
25202 M3 x 10mm FHCS 10
25204 M3 x 16mm FHCS 10
25211 M3 x 10mm BHCS 10 71032
25612 M3 Locknut, with Flange 10
71003 Shock Tower Set 1 71032
71066
71032 M2.5 x 14MM SHCS 10 71066
71038 Rear Body Mounts 1
71066 Body Posts and Body Mount 1 71032
89204 M3 x 24mm BHCS 10
91444 Shock Bushing Composite 4 21173
25202
91477 M3 Nut, Black 6 71038
91478 M3 x 30mm BHCS 10
71038 71066
25187
25187 71032
25211
25612
91444
71038 91478

89204 91477 25211

91477
91478

91444

25612
89204

25204 71003
 27
:: Chassis
6338 Antenna Tube & Cap (black) 1
25187 M3 x 14mm BHCS 10
25203 M3 x 12mm FHCS 10 25225
25204 M3 x 16mm FHCS 10
25211 M3 x 10mm BHCS 10 6338
25225 M3 x 3mm Set Screw 10
31383 Ballstud Washer, 5.5 x 2mm, 10
Blue Aluminum 6338
31509 M2 x 3mm BHCS 10
31521 M2.5 x 8mm BHCS 10 25211
71015 Front and Rear Arms Set 1 25211 25211
71023 Receiver Box Seals 1
71024 Chassis 1 71026
71026 Receiver Box 1
71049 Hinge Pin Brace 1
71067 Front Bumper and Nerf Guards 1
89208 M3 x 14mm FHCS 10
91049 Heavy-Duty Ballstud, 10mm 10 71023
91358 Chassis Brace Set 1
91359 Arm Mounts, Braces, and Bulkhead 1
91394 Hinge Pin Set, B5 1 31383 91049
71026
71023
31383
25211

25211
25211
25211
71067
91358

25211 31521 71015 25187

91359
91394

91359
25211 91359

25211 91394 71015

71049
31509
91359
71024 89208
25203
71067 25203
25204 89208

:: Anti-Roll Bars
7186 M2x6mm SHCS 10
25225 M3x3mm Set Screws 10 71086
71086 Anti-Roll Bar Mounts and Steering Rod Ends 1 25225
71091 FT DR10 Anti-Roll Bar Set 1
81150 RC8B3 Anti-roll Bar Drop Link/Collet 1 81150
89219 M3x5mm Set Screws 10 71091

71091
71086
71086
25225
71086
71086
7186 71086
7186
89219 7186
7186
7186 81150 71091
89219 7186
71086
71086
28
:: Factory Team and Option Parts :: Reedy Batteries and Chargers
1408 FT Ti Turnbuckle, 2.65”/67mm (blue) Pr. 302 AA Alkaline 1.5V (4) 1
1409 FT Ti Turnbuckle, 1”/25.5mm (sway bar) (blue) Pr. 996 5.0mm 1S-2S Balance Charge lead w/SP Clip (4mm) 1
1736 FT Blue Body Clip, short 6 997 4.0mm 1S-2S Balance Charge lead w/SP Clip (4mm) 1
7495 Vented V2 Slipper Hubs 2 998 5.0mm 4S Balance Charge Lead (4mm) 1
21173 Body Clips 10 999 Saddle Pack Balance Charge Clip 1
25392 FT Locknuts, 3mm Aluminum, Blue 10 27200 1216-C2 Dual AC/DC Competition Battery Charger 1
27128 Servo Washers, Aluminum, Black 4 27201 324-S AC LiPo/LiFe Compact Balance Charger 1
31381 FT Ballstud Washer, Aluminum (0.5mm) 10 27201C2 324-S Charger w/3300mAh 7.4V LiPo Battery 1
31382 FT Ballstud Washer, Aluminum (1.0mm) 10 27201C2 324-S Charger w/4500mAh 11.1V LiPo Battery 1
31383 FT Ballstud Washer, Aluminum (2.0mm) 10 27201C3 324-S Charger w/4000mAh 14.8V LiPo Battery 1
71014 Clamping Wheel Hex (8.5mm) 2 27202 123-S AC LiPo Compact Balance Charger 1
71019 HD CVA Axle, T5M 2 27220 7-in-1 Universal Charge Lead (4mm) 1
71072 Rear Drag Slick Tires and Wheels, Mounted 2 27221 T-plug Charge Lead (4mm) 1
71073 Front Drag Slick Tires and Wheels, Mounted 2 27222 XH 2-6S Balance Board (4mm) 1
71078 Rear Drag Wheels, 2.2”/3.0” 12mm Hex, Black 2 27223 RX Charger Lead FUT (4mm) 1
71079 Front Drag Wheels, 2.2”, 12mm Hex, Black 2 27224 US to IEC 320 C5 angle 1M AC Power Cord 1
71082 Reakt Drag Body, Clear 1 27226 EU to IEC 320 C5 angle 1M AC Power Cord 1
71083 Reakt Drag Body, Painted (Orange) 1 27232 4mm/5mm Pro Charge Lead 1
71084 Reakt Drag Body, Painted (Green) 1 27313 LiPo Pro TX/RX 2400mAh 7.4V Flat 1
71091 FT DR10 Anti-Roll Bar Set 1 27315 LiFe Pro TX/RX 1600mAh 6.6V Flat 1
91177 VTS Slipper Pads 2 27317 Wolfpack HV LiPo 50C 5100mAh 7.6V Stick 1
91178 VTS Slipper Plate 1 27318 Wolfpack HV LiPo 50C 4200mAh 7.6V Shorty 1
91179 FT VTS Slipper Hub, outer 1 27319 Wolfpack HV LiPo 50C 3300mAh 7.6V LP Shorty 1
91197 LCF Slipper Pads 2 27343 Zappers SG3 9600mAh 85C 7.6V Stick 1
91304 FT 12 mm Threaded Collars - 2 27344 Zappers SG3 8200mAh 115C 7.6V Stick 1
Used with threaded shock bodies 27345 Zappers SG3 6000mAh 115C 7.6V LPStick 1
91383 FT Aluminum Arm Mount (C) 1 27346 Zappers SG3 5500mAh 85C 7.6V ULP Stick 1
91385 Arm Mount Inserts Set (C), B5 1 27347 Zappers SG3 6100mAh 85C 7.6V Shorty 1
91387 FT Aluminum Arm Mount (D) 1 27348 Zappers SG3 4800mAh 115C 7.6V Shorty 1
91389 Arm Mount Insert (D), B5 1 27349 Zappers SG3 4100mAh 85C 7.6V LP Shorty 1
91392 Aluminum Steering Set, B5 1 27350 Zappers SG3 3600mAh 115C 7.6V LP Shorty 1
91447 Shock Bushing Ball, B5 - Req. #91446 4
91464 FT Aluminum Gear Diff Cover 1
91492 12mm V2 Bleeder Gasket/Screw 1
91493 FT Low Friction X-Rings 8 :: Reedy Electronics
91495 12mm V2 X-Ring Rebuild Kit 1 27002 Blackbox 800Z 2S Zero-Timing Competition ESC 1
(4 clear x rings, 2 spacers, 4 hat bushings) 27004 Blackbox 510R Competition ESC 1
91548 RC10B5 Aluminum Rear Hubs (Blue) Pr. 27005 Blackbox 510R Competition ESC w/PROgrammer2 1
91550 RC10B5 Rear Hub Bearing Inserts 2 ea. 27006 Blackbox 600Z 2S Zero-Timing Competition ESC 1
91553 Factory Team Bearing Kit, B5, B5M, T5M, SC5M 1 27024 Blackbox Pro Capacitor Unit 1
91560 5x10x4mm Factory Team Bearings 4 27027 Blackbox PROgrammer2 1
91562 6x13x5mm Factory Team Bearings 4 27028 Blackbox 30x30x7mm Fan w/screws 1
91563 10x15x4mm Factory Team Bearings Titanium 4 27029 Blackbox Pro Modified Capacitor Unit 1
91577 FT 12 x 27.5 Shock Body (V2), threaded 2 27030 Blackbox ESC/Programmer2 Connection Wire 1
91579 FT 12 x 36 Shock Body (V2), threaded 2 27031 Blackbox 510R 30x30x10mm Fan w/screws 1
91580 Titanium Screws, 3x6mm BHCS 4 27033 Blackbox 1000Z+ Pro Competition ESC 1
91581 Titanium Screws, 3x8mm BHCS 4 27100 RS1206 Digital HV Hi-Speed Competition Servo 1
91582 Titanium Screws, 3x10mm BHCS 4 27101 RT1508 Digital HV Hi-Torque Competition Servo 1
91583 Titanium Screws, 3x12mm BHCS 4 27102 RS1206 Servo Case Set w/screws 1
91584 Titanium Screws, 3x14mm BHCS 4 27103 RS1206 Servo Gear Set 1
91585 Titanium Screws, 3x16mm BHCS 4 27105 RT1508 Servo Gear Set 1
91588 Titanium Screws, 3x22mm BHCS 4 27110 0712MG Digital RTR Servo 1
91589 Titanium Screws, 3x24mm BHCS 4 27111 1514MG Digital RTR Servo 1
91592 Titanium Screws, 3x8mm FHCS 4 27113 RT1709 Digital HV Low-Profile Brushless Comp.Servo 1
91593 Titanium Screws, 3x10mm FHCS 4 27114 RT2406 Digital HV Brushless Competition Servo 1
91594 Titanium Screws, 3x12mm FHCS 4 27129 0712MG Servo Gear Set 1
91595 Titanium Screws, 3x14mm FHCS 4 27130 1514MG Servo Gear Set 1
91596 Titanium Screws, 3x16mm FHCS 4 27133 RS1306 Gear Set 1
91597 Titanium Screws, 3x18mm FHCS 4 27134 RT1709 Gear Set 1
91609 Clamping Wheel Hex, (5.0mm offset) 2 27135 RT2406 Gear Set 1
91610 Clamping Wheel Hex, (7.0mm offset) 2 27136 RT2706A Gear Set 1
91619 3 x 27.5 Shock Shafts (V2), TiN 2 27137 RS1306 Case Set 1
91620 FT 3 x 27.5 Shock Shafts (V2), Chrome 2 27138 RT1709 Case Set 1
91623 3 x 35 Shock Shafts (V2), TiN 2 27139 RT2406 Case Set 1
91624 FT 3 x 35 Shock Shafts (V2), Chrome 2 27140 RC2312 Gear Set 1
91626 FT 12mm Pistons (V2), 2 x 1.6, flat 4 27141 RC2312 Case Set 1
91627 FT 12mm Pistons V2, 2 x 1.7, flat 4
91628 FT 12mm Pistons (V2), 3 x 1.4, flat 4
91630 FT 12mm Pistons (V2), Blank, flat 4
91631 FT 12mm Pistons (V2), 3 x 1.4, tapered 4
91633 FT 12mm Pistons (V2), Blank, tapered 4
91727 FT 3x48mm Titanium Turnbuckle Set 1
 29
:: Reedy Motors :: Tools
280 Sonic 540-M3/M4 Rotor Spacer Set 1 1111 FT Turnbuckle Wrench 1
281 Sonic 540-M3/M4 Case Screws w/Insulator 1 1112 FT 4mm Turnbuckle Wrench 1
293 Sonic 540 FT 17.5 Fixed Timing 1 1113 12mm Big Bore Shock Tool 1
294 Sonic 540 FT 13.5 Fixed Timing 1 1114 FT Dual Turnbuckle Wrench 1
295 Sonic 540-FT Spec Rotor 12.0 x 7.25 x 25.3 1 1449 Off Road Ride Height Gauge 1
297 Sonic 540 FT 21.5 Fixed Timing 1 1452 FT TC Ride Height Gauge 1
27400 S-Plus 25.5 Spec 1 1498 FT Universal Tire Balancer 1
27401 S-Plus 21.5 Spec 1 1499 FT Body Reamer 1
27402 S-Plus 17.5 Spec 1 1500 FT 1.5mm Hex Driver 1
27403 S-Plus 13.5 Spec 1 1501 FT 2.0mm Hex Driver 1
27404 S-Plus 10.5 Spec - Torque 1 1502 FT 2.0mm Ball Hex Driver 1
27414 540-M3/S-Plus Spec Rotor 12.5 x 7.15 x 24.2 1 1503 FT 2.5mm Hex Driver 1
27415 540-M3/S-Plus Spec Rotor 12.3 x 7.15 x 24.2 1 1504 FT 2.5mm Ball Hex Driver 1
27416 540-M3/S-Plus Spec Rotor 12.0 x 7.15 x 24.2 1 1505 FT 3.0mm Hex Driver 1
27417 S-Plus Screw Set 1 1506 FT 5.0mm Hex Driver 1
27418 540-M3/S-Plus Lightweight Sensor Board 1 1507 FT 5.5mm Nut Driver 1
27420 540-M3/M4/S-Plus Aluminum Case Screw Set 1 1508 FT 7.0mm Nut Driver 1
27421 540-M3/M4/S-Plus Aluminum Timing Screw Set 1 1510 FT 1.5mm Hex Replacement Tip 1
27428 S-Plus 21.5 Spec - Torque 1 1511 FT 2.0mm Hex Replacement Tip 1
27429 S-Plus 17.5 Spec - Torque 1 1512 FT 2.0mm Ball Replacement Tip 1
27435 Sonic 540-M4 Modified Motor 21.5 1 1513 FT 2.5mm Hex Replacement Tip 1
27436 Sonic 540-M4 Modified Motor 17.5 1 1514 FT 2.5mm Ball Replacement Tip 1
27437 Sonic 540-M4 Modified Motor 13.5 1 1515 FT 3.0mm Hex Replacement Tip 1
27438 Sonic 540-M4 Modified Motor 9.5 1 1518 FT Hex Driver Tool Set (3pcs) 1
27439 Sonic 540-M4 Modified Motor 8.5 1 1519 FT Hex/Nut Driver Tool Set (5pc) 1
27440 Sonic 540-M4 Modified Motor 8.0 1 1522 FT Digital Scale, 100/0.01g 1
27441 Sonic 540-M4 Modified Motor 7.5 1 1555 FT Clutch Gauge, 4 Shoe 1
27442 Sonic 540-M4 Modified Motor 7.0 1 1568 FT 5.5mm Short Nut Driver 1
27444 Sonic 540-M4 Modified Motor 6.5 1 1569 FT 7mm Nut Driver, T-Handle 1
27445 Sonic 540-M4 Modified Motor 6.0 1 1570 FT 5.5mm Short Nut Driver 1
27446 Sonic 540-M4 Modified Motor 5.5 1 1571 FT 1:8 Wheel Nut Wrench, 17mm Hex 1
27447 540-M4 Mod Rotor 12.5 x 7.25 x 25.3 1 1579 FT Ball Cup Wrench 1
27448 540-M4 Mod Rotor 12.5 x 5.0 x 25.3 1 1595 Chassis Weights, 1/4 oz 1
27449 540-M4 Mod Rotor 13.0 x 5.0 x 25.3 1 1650 7 Piece Hex Driver Set 1
27450 540-M4 Mod Rotor 12.0 x 5.0 x 25.3 1 1657 FT 1/4” Hex Drive .050” Tip 1
27451 Sonic 540-M4 Modified Motor 5.0 1 1659 FT 1/4” Hex Drive 5/64” - 2.0mm Tip 1
27452 Sonic 540-M4 Modified Motor 4.5 1 1661 FT 1/4” Hex Drive 1.5mm Tip 1
27453 Sonic 540-M4 Modified Motor 4.0 1 1662 FT 1/4” Hex Drive 2.5mm Tip 1
27454 Sonic 540-M4 Modified Motor 3.5 1 1666 FT 1/4” Hex Drive 5.5mm Nut Driver Tip 1
27455 540-M4 Sensor Board 1 1667 FT 1/4” Hex Drive 7.0mm Nut Driver Tip 1
27456 540-M4 Ball Bearing Set 1 1668 FT 1/4” Hex Drive 8.0mm Nut Driver Tip 1
27459 Sonic 540-M4 Modified Motor 10.5 1 1674 FT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1
27460 540-M4 Mod Rotor 12.3 x 5.0 x 25.3 1 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)
1675 FT Shock Shaft Pliers 1
1679 FT T-Handle Ratchet Driver 1
:: Reedy Accessories 1719 FT Camber + Track Width Tool 1
1737 FT Body Scissors 1
643 Low Profile Bullet Plug 4mm x 14mm (2) 1
3718 12 Inch Nylon Wire Ties 12
644 Low Profile Bullet Plug 4mm x 14mm (10) 1
3987 FT Droop Gauge 1
645 Low Profile Bullet Plug 5mm x 14mm (2) 1
89240 RC8 FT Turnbuckle Wrench 1
646 Low Profile Bullet Plug 5mm x 14mm (10) 1
647 Silicone Wire 12AWG-Black (1m) 1
648 Silicone Wire 14AWG-Black (1m) 1
650 Shrink Tubing - 15pcs 4.5mm x 20mm 1
747 Silicone Wire 12AWG-Black (30m) 1
790 Silicone Wire 13AWG-Black (1m) 1
791 Silicone Wire 13AWG-Black (30m) 1
792 Low Profile Caged Bullet Plug 4mm x 14mm (2) 1
794 Low Profile Caged Bullet Plug 5mm x 14mm (2) 1
:: Contact Information
978 Flat Sensor Wire 70mm 1 Check out the following web sites for all of our electric kits,
979 Flat Sensor Wire 110mm 1 current products, new releases, setup help, tips, and racing info!
980 Flat Sensor Wire 150mm 1
981 Flat Sensor Wire 200mm 1 Associated Electrics, Inc.
982 Flat Sensor Wire 270mm 1 21062 Bake Parkway
994 Flat Sensor Wire 125mm 1 Lake Forest, CA 92630-8853 USA
995 Flat Sensor Wire 175mm 1 http://www.TeamAssociated.com
27423 30mm Lightweight Motor Fan w/195mm ext. 1 http://www.RC10.com
27457 30mm Aluminum Motor Fan w/195mm extension 1 http://twitter/Team_Associated
27458 40mm Aluminum Motor Fan w/195mm extension 1 http://www.instagram.com/teamassociatedrc/
http://www.facebook.com/TeamAssociated/

:: XP Electronics call: (949) 544-7500

29203 AE XP120 2.4GHz Radio System 1 fax: (949) 544-7501
29204 AE XP-R4 2.4GHz 4CH Receiver 1