GPS Vehicle tracker

(GPS+GSM+SMS/GPRS)

GT02N User Manual

(Version 2.1)

Thank you for purchasing the tracker. This manual shows how to operate

the device smoothly and correctly. Please make sure to read this manual

carefully before using this product. Please note that specification and

information are subject to changes without prior notice in this manual.

Any change will be integrated in the latest release. The manufacturer

assumes no responsibility for any errors or omissions in this document.

1. Summary

Working Based on existing GSM/GPRS network and GPS

satellites, this product can locate and monitor any

remote targets by SMS or internet.

Overview of the characteristics:

1.GSM 850/900/1800/1900MHZ.

2.GPS position.

3.Auto set APN.

4.180Mah Battery inside, Power-Cut alarm.

5.Motion detect, save GPRS flow and power.

6.GEO-fence Alarm.

7.SOS Alarm.

8.Vibration Alarm.

9.ACC Alarm.

10.Speed Alarm

11.Voice Surveillance.

12.Voltage Range: DC 10V-40V.

13.Enginee Cut off.

2．Accessories：
Power line: Relay: Microphone:

SOS line: Manual

3. Specs
1）.GSM：850/900/1800/1900MHZ

2）.GPRS: Class12, TCP/IP

3）.Working Voltage：10V-40V DC

4）.Working current：≈22mA (12VDC)

5）.Working current：≈12mA (24VDC)

6）.GPS locating time：Cold start≈38s（Open sky）

Warm start≈32s

Hot start≈2s（Open sky）

7）.GPS Precision：10m（2D RM）

8）.Working temperature：-20℃～+70℃

9）.Working humidity：20%～80%RH

10）.Measurement：97（L）×50（W）×15（H）mm
4. Wire defined
The 2pins orange plug connect with SOS line

The 2pins blue and green plug connect with microphone.

The 4pins plug connect with power line.

For 4pins power line:

The red wire connect with power DC12V+

The black wire connect with power DC12V-

The white wire from tracker connect with yellow line from

relay,the white line from relay connect with power DC12V+.

Then cut the power + wire of pump to 2 sides.

Every side connect with relay green line.

5.Device status indicators

5.1 Connect DC 10-40V power supply, push the switch (switch beside

the SIM card holder), the red LED will light continuously.

5.2 The blue LED light continuously when searching the GPS signal.

Once GPS fixed, the blue LED will be flashing.

5.3 The intermediate green LED (GSM signal state) GSM signal is

normal, green LED flashing. No GSM signal, the green LED light

continuously.

6.Installation

6.1 Prepare for installation

6.11 Product Check. Open the packing box and check the device’s model
 and accessories. If the model is wrong or the accessories not

complete, please contact the dealer.

6.12 Choose SIM card. Please insert a SIM card which support GSM 2G

network to the device. Please take dealer’s advice as reference.

6.13 SIM card installation. Discharge the cover of the device and uncover

the SIM card holder. Then insert the SIM card and cover SIM card

holder (as follows).

6.14 Open the cover, Push the switch. Then Put back the front cover.

6.15 Connect the device to the 10V-40V power supply.

6.16 Install the device in the hidden place of the car；

The SIM card must be with GPRS function and enough deposit. If your

SIM card need input PIN when power on, please cancel it.

6.2 Installation

The GPS tracker must be installed under professional

personnel.

Note：

1) Please install the device in the hidden place as

followings：
 2) Avoid being placed with signal radiators like reverse

sensor ；

3) The device has GSM antenna and GPS antenna inside. Please

ensure the receiving side of the device is face up and

without metal cover.

Note: The metal cover will lessen the receiving of GPS

signals.

7. Device wiring requirements

7.1 The device power supply is DC 10V-40V. The red line is

positive pole while the black line is negative pole.

7.2 The negative pole of power supply connects with ground or

the metals. Please do not connect with other ground lines.

7.3 When finishing the power supply wire connection, please

make the plug of power supply to the device, the switch beside

sim card holder.

8.The Device Working

8.1 Power on: Connecting to the power. Then the three LED indicators will

light. The device will upload the data to the online platform

(the default interval of uploading data is 15seconds). When the

car is in static state for a long time, the device will be in

energy saving mode.

8.2 Power off：Pull off the power plug then power off the device.

9.User Settings

9.1 SMS Commands instruction

1)Center Number

Text
Parameter Sample
command

710#number# 710#13500135000#
CENTER Add
711#number# 711#13800138000#

CENTER Del D01# D01#

 D02# D02#

1)Center number can control the oil and

power and resume factory settings

2) Center number can receive the call and

text of vibration alarm and over speeding

Command alarm.

Description 3) SIM must display the income call number

to control oil and power.

4) Only 2 number can be center number.

5) Change center number must resend the

command.

Command
Successful Setting：Add admin account 1 OK!
Feedback

2) View Center Number

Text Parameter Sample

command

View 901# 901#

Command This directive is used to view Device

Description Manager number.

Command Successful Setting：Admin1:

Feedback Admin2:

3)Authorized Number Set

Text Parameter Sample

command

Authorized 101# number # 1：101#13800138000#

Add 102# number # 2：102#12345678912#

103# number # 3：103#12345678912#

Authorized D11# D11#

Del D12# D12#

D13# D13#

Command 1) Authorization number for SMS control

Description oil.

2) Only three numbers to set the

authorization number

3) Change the authorization number needs

to delete the previous number

Command Successful Setting： Add Authorization

Feedback account 1 OK!

4) View Authorized Number

 Text Parameter Sample

command

View C10# C10#

authorized

Command This directive is used to view the

Description equipment authorization number

Command Successful Setting：

Feedback Authorization 1：

Authorization 2：

Authorization 3：

5)APN Setting

Text
Parameter Sample
command

802#APN#username#passw 1：802#intenet#123#123#
APN Setting
ord# 2: 802#internet#

APN differs according to the local telecom

Command operators.

Description For example：APN request password，please refer to

Sample 1，and Sample 2 for no password.

Command Successful Setting：SET APN OK！

Feedback

6) Set Server

Text
Parameter Sample
command

SERVER 1.803#gps.dyegoo.net#6100#
803#SERVER#port#
Parameter 2: 803#47.90.39.27#6100#

View SERVER CIP# 1）CIP#

Change the IP and port when move to a new

Command server

Description port：10~65535

Command
Successful Setting：set IP OK!
Feedback

7)Moving Time Interval

Text
Parameter Sample
command

TIMEER

Parameter 730#upload interval# 730#20#

setting
 Scope ： 0 ， 10~60 seconds ； 0,no data

Command uploading；

Description 10~60,means time interval ； the default

value is 15 seconds.

Command
Successful Setting：SET TIMER OK！
Feedback

8)Static Time Interval

Text
Parameter Sample
command

STATIC SUP#time interval# SUP#5#

Command
Scope：1~60 minutes；

Description The default time interval is 5 minutes.

Command
Successful Setting：SET STATIC TIME OK！
Feedback

9) Cancel the continuous upload

Text
Parameter Sample
command

NUP NUP# NUP#

Command This command is used to cancel sending data

Description to the platform

If need again to restore the uploading,

need to send TIMEER Parameter setting.

Command
SET OK！
Feedback

10)Oil-Cut

Text
Parameter Sample
command

RELAY 222# Cut off oil and

222#
Parameter1 power

RELAY 333#
333#
Parameter2 Recover oil and power

1)RELAY control the start and closeness of

the relay

2) Only the center number can operate.

3）The device only cut off the oil circuit

on the condition of the driving speed below

Command
20KM/H or in static state.
Description
4)When send the command, the device will

reply ‘please waiting’When the vehicle

speed is over 20KM/H, the device will cut

off the oil or the power when the speed

 below 20KM/H.

Successful Setting：Fuel cut has already

Feedback been completed OK!

11)GMT

Text
Parameter Sample
command

801#E8#
GMT 801#location time Zone#
801#W4#

The default time zone is Beijing time.

Command
please operate according to the above
Description
command.

Command
Successful Setting：Set time zone ok!
Feedback

12)Vibration Alarm

Text command Parameter Sample

Open Vibration 911# 911#

Alarm

VIBRATION 123#sensitivity#alarming 1)

Parameter way# 123#2#3#

1)
Set into
V123#2#
vibration V123#2#
2)
alarm time
V123#1#

Cancel

vibration 456# 456#

alarm

The sensitivity value of the vibration

is from 1 to 5，1is the most sensitive

and o is close. Alarming ways: 1,

Command
calling 2, texting, 3 Calling and
Description
texting.

Need set the center number and receiving

number.

Command
Set vibration alarm level，OK!
Feedback

13)Speed Alarm
Text
Parameter Sample
command

SSA#speed#alarm
1) SSA#120#
way#
SPEEDING 2) SSA#150#3#
Or
Parameter 1) 667#120#
667#speed#alarm
way#
2) 667#150#3#

The speed scope is form 60-220, if the

speed isnot in this cope, the alarm is off.

Command Alarming ：1. calling, 2. texting,

Description 3.calling and texting.

Need set the center number and receiving

number.

Command
Successful Setting：set speeding alarm，OK!
Feedback

14)ACC Alarm

Text
Parameter Sample
command

Open ACC
840#1# 840#1#
Alarm
Close ACC
840#0#
ALARM

15)Reset

Text
Parameter Sample
command

RESET 930# 930#

Command
Reset the device
Description

Feedback Successful Setting：Reset system, ok!

16)Factory

Text
Parameter Sample
command

Parameter 940# 940#

Restore the factory setting

Only center number can initial this

Description function

Factory setting will recover to the

original setting

Feedback Successful Setting：FACTORY OK！

17)Language Setting

command Parameter Sample

LANG LANG1# LANG1# 1:CHINESE，

Parameter LANG0# LANG0#：ENGLISH

When check the location, it will reply the

Command Chinese location in Chinese language

Description setting; while reply the URL link when in

English language setting.

Feedback Successful Setting：SET LANG OK！

18) GEO-fence Setting

Text
Parameter Sample
command

Setting 920#radius#way# 920#1#2#

Cancel 921# 921#

Setting Geo-fence alarm, radius from 1-

100, Unit: 100 meter.

Command
Alarming ：1, calling 2, texting
Description
Out Geo-fence 1 time, the Geo-fence

canceled.
 Feedback Set Enclosure-2 OK / Cancel Enclosure OK

19)Position

Text Parameter Sample

command

command 988# 988#

Command Check the longitude and altitude and

Description other information of the device

Command Reply with longitude and altitude, speed

Feedback and IMEL.

20)Google Link

Text
Parameter Sample
command

command 666# 666#

Command

Descripti Check the location link of Google map

on

<Datetime:12-07-05 13:21:30>
Command
http://maps.google.com/maps?q=N22.540885,E113.
Feedback
95265
21)Version

Text
Parameter Sample
command

VERSION V00# V00#

Command The command is to check the software

Description version

Command VERSION:Xxxx

Feedback BUILD:2012-07-05 10:12

22)Param Check

Text
Parameter Sample
command

PARAM 886# 886#

Command The command is to check the settings and

Description the default parameter.

IMEI:351190012535936

APN : cmnet
Command
IP:IP and port
Feedback
TIMER: moving uploading interval

STATIC: static uploading interval

 CENTER: center number

LANG: language(CN/EN)

GMT: time zone (E/W8)

23)Status Check

Text
Parameter Sample
command

STATUS 902# 902#

Command The command is designed for checking the

Description device’s working status.

External power:ON/OFF

GSM Signal:HIGH/MIDDLE/LOW
Command
GPS:FIXED/UNFIXED
Feedback
RELAYER:DISABLE/ENABLE

Vibrate Warning:ON/OFF

24)Monitor(Voice Surveillance)-CALL BACK(default)

command Parameter Sample

SSS# SSS# SSS#

Using Command Send this command to

Description
the tracker’s number, the tracker
 will call back to admin number.

25) Monitor (Voice Surveillance)-CALL

command Parameter Sample

Open Calling mode SS1# SS1#

Return to Call SS0#

SS0#
back

26)Wire-cut Alarm; Low Battery Alarm

command Parameter Sample

Disable 555# 555#

Enable 666# 666#

9.2 Platform
Website: http://www.dyegoo.net
Please click English to change to English language.
Login as Account or ID,ID is 11bits numbers, it is in the label on
the tracker.

Enter ID
The default Password:123456
APP: Please search DYEGOO in Google store or Apple store.

In production, IP, port have been written in, normally the tracker
will be auto online, if the tracker offline, Please set APN by SMS
command.
Please get APN from sim card inserted mobile operator.
For example,if you are in Brazil, and the sim card in the tracker is
from Claro.
Please send below SMS command to set APN:
802#java.claro.com.br#claro#claro#

If you lost IP, port, please send below SMS command by admin
number to set them back：
803#gps.dyegoo.net#6100#
Or
803#47.90.39.27#6100#
10.Trouble shooting

10.1 The device is not online or offline on the web

platform.

10.1.1 First, please check the three LED working state.

If possible. You can call the device’s number to check.

● If not connected, the device is out of signal. If

the GSM signals cannot reach your location, please

drive to the open sky.

⚫ If reminding the device SIM card is out of deposit,

please make deposit by the telecom operator.

● If you can connect to the device when calling, the SIM

card has deposited and please check with your operator for
GPRS function. You also can check by searching the
internet on your mobile phone.

● If reminding the device is power off, please turn back

the device and proceed as followings:
a)Check if the red LED is in constant glow. If the LED is
dark, please check the power connecting. If fuse is
broken, please return the device to the seller.
 b)If the green GSM LED is not in constant glow, please

check the installation of SIM card.

10.1.2 Please check the offline area in order to judge if

the network problem of operators.

10.2 When GPS cannot receive the signals, please drive in

the open sky and ensure there is no metal thins on the

device.

10.3 When the device cannot receive the GSM signal, please
check the SIM card installation. If the GSM signals cannot
reach your location (such as the basement), please drive
to the open sky.