16-54 ELECTRICAL SYSTEM
Speedometer (Optional Part for U.S. Model)
Speedometer Circuit
1. Speedometer (except US Model) 2. Speed Sensor 3. Ignition Switch 4. Main Fuse 30 A 5. Battery
ELECTRICAL SYSTEM 16-55
LED Indicator
Drive Belt Failure Mode Memory Clearing Procedure
A flashing CHECK BELT warning LED (Light Emitting Diode) light means that the drive belt needs inspection. The belt warning light will activate every 100 key-on hours, or sooner if the belt becomes damaged or fails.
NOTE
Follow the instruction on pages 2-14 to 2-16 of this Service Manual to complete the necessary inspections. After completing the inspections, follow these instructions to clear the system memory and stop the flashing light. ignition Turn off the the beltswitch. at the 2 pin connector [A] Disconnect switch above the torque converter cover. pin connectors Disconnect both sets of 5converter cover. [B] which are located above the torque
pin connectors to their opposite gray Reconnect these 5to gray. to black and black
Turn on the ignition switch. [A]. belt warning light Observe theflashing at a 0.4 second interval. It should be
Let it flash for at least seven seconds.
NOTE
More than seven seconds is OK. The 4WD LED light [B] will also flash only if 4WD is selected. While observing the belt warning light, turn off the ignition switch.
16-56 ELECTRICAL SYSTEM
LED Indicator
mismatched 5 connector re Disconnect thenormally. (Blackpinblack, gray sets and [A] connect them to to gray) Connect the belt switch 2 pin connector [B].
Turn on the ignition switch. are flashing. warning Confirm that nogo on forlightssecond. The LED lights one Remove: (see Frame chapter) Front Fender
Handlebar Cover Disconnect: LED Indicator Lead Connector [A] Remove: Screws [B] and Collars LED Indicator [C] and Bracket
LED Indicator Removal
LED Indicator Installation
Install: [A] Bracket
LED Indicator [B] Screws [C] and Collars [D]
ELECTRICAL SYSTEM 16-57
LED Indicator
LED Indicator Inspection
Flashing Pattern Inspection LED BELT and 4WD Indication Pattern Condition Ignition Switch ON Normal Check
BELT and 4WD
Ignition Switch OFF Normal
BELT
Drive Failure Detecting Switch OFF (Belt Failure)
BELT
Total 100 hours of use
BELT and 4WD
Drive Belt Failure Mode Memory Clearing Procedure
BELT and 4WD
Ignition Switch OFF Memory Writing Failure
BELT
Memory Writing Time Limit (one hundred thousand)
BELT
Memory Reading Failure
4WD
2WD/4WD Actuator Failure
16-58 ELECTRICAL SYSTEM
LED Indicator
LED Indication Pattern Condition Engine Brake Actuator Failure Check
4WD
10
4WD
Both 2WD/4WD Actuator and Engine Brake Actuator Failure
11
Check 1 No Problem Check 2 No Problem Check 3 Check the drive belt (see Drive Belt Deflection Inspection and Drive Belt Inspection in Periodic Maintenance chapter). If it is flashed by abnormal belt, replace the belt and torque converter cover. After completing the inspections, do the drive belt failure mode memory clearing procedure (see Drive Belt Failure Mode Memory Clearing Procedure).
Check 4 Check the drive belt (see Drive Belt Deflection Inspection and Drive Belt Inspection in Periodic Maintenance chapter). After completing the inspections, do the drive belt failure mode memory clearing procedure (see Drive Belt Failure Mode Memory Clearing Procedure). Check 5 This flashing is the indication pattern for the drive belt failure mode memory clearing procedure.
Check 6 The LED indicator may be broken. Do the drive belt failure mode memory clearing procedure. If the same flashing appears, replace the LED indicator. Check 7 The writing memory in the LED indicator is a limit (one hundred thousand times). Replace the LED indicator. Check 8 The LED indicator may be broken. Do the drive belt failure mode memory clearing procedure. If the same flashing appears, replace the LED indicator. Check 9, 10, 11 See Actuator Control System Troubleshooting.
ELECTRICAL SYSTEM 16-59
LED Indicator
LED Indicator External Circuit 1. LED Indicator 2. CHECK BELT LED 3. 4WD LED 4. Reset Connector 5. Battery 6. Ignition Switch 7. Drive Belt Failure Detecting Switch 8. Igniter 9. Input (from Drive Belt Failure Detecting Switch) 10. Output (to LED Indicator) 11. Actuator Controller 12. 2WD/4WD Shift Switch
16-60 ELECTRICAL SYSTEM
LED Indicator
Led Indicator Circuit
1. LED Indicator 2. Drive Belt Failure Indicator LED (CHECK BELT) 3. 4WD Mode Indicator LED (4WD) 4. Drive Belt Failure Mode Reset Connector 5. Igniter 6. 2WD/4WD Shift Switch 7. Acturator Controller 8. Engine Brake Actuator
9. 2WD/4WD Actuator 10. Battery 11. Main Fuse 30 A 12. Ignition Switch 13. Drive Belt Failure Detecting Switch Fuse 5 A 14. Drive Belt Failure Detecting Switch
