Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve

Characteristics Series D1FB

The proportional directional valves D1FB (NG06) are

available with and without onboard electronics (OBE).
D1FB OBE:
The digital onboard electronics is situated in a robust
metal housing, which allows the usage under rough en-
vironmental conditions.
The nominal values are factory set. The cable connection
to a serial RS232 interface is available as accessory.

3
D1FB for external electronics:
D1FB D1FB OBE
The parameters can be saved, changed and duplicated in
combination with the digital power amplifier PWD00A-400.
The valve parameters can be edited with the common
ProPxD software for both versions. A B A B
The D1FB valves can be ordered with spool/sleeve design
(D1FB*0) for maximum precision as well as spool/body a 0 b a 0 b
design (D1FB*3) for high nominal flow - see functional P T P T
limit curves for maximum flow capability.
Valves with explosion proof solenoids Ex e mb ll see
catalogueMSG11-3343.
Download: www.parker.com/ISDE, see “Support” D1FB D1FB OBE

Features
• Spool/sleeve and spool/body
• 3 command options for D1FB OBE:
+/- 10 V, 4…20 mA, +/- 20 mA
• High repeatability from valve to valve
• Low hysteresis
• Manual override
• Digital onboard electronics

D1FB*0 OBE D1FB*3 OBE

Spool/sleeve design Spool/body design

Parametrizing connection

Main connection
(always on B-side)

Manual
override

A B A B

D1FB UK.indd 25.03.24

3-3 Parker Hannifin Corporation

 Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Ordering Code Series D1FB

D1FB

D 1 F B 0 N
Directional Size Proportional Standard Spool Spool Seals NBR Solenoid Connector Design Design
control DIN NG06 control dynamics type position (other seal series
valve CETOP 03 standard compounds (not required
on request) for ordering)
NFPA D03 repeatability

3 D1FB*0: Spool/sleeve design

Flow [l/min]
Code Design
Spool/sleeve
Code Spool type at Dp 5 bar 0
design
per metering edge Spool/body
Overlap 3
design
E01C A B 6
E01F 12
E01H P T 20
E02C 6 Code Connector
E02F 12 1) Connector as per
E02H 20 W
EN 175301-803
E03C 6 Connector
E03F 12 J 1) 2)
DT04-2P "Deutsch"
E03H 20
QB = QA /2
B31F 12 / 6
B31H 20 / 10
D1FB*0: Spool/sleeve design
QB = QA /2 Code Solenoid
B32F 12 / 6
B32H 20 / 10 M 9 V / 2.7 A
J 24 V / 0.8 A

D1FB*3: Spool/body design

D1FB*3: Spool/body design
Flow [l/min]
Code Spool type at Dp 5 bar Code Solenoid
per metering edge K 12 V / 2.2 A
Overlap J 24 V / 1.1 A
E01F A B 10
E01H 20
E01K P T 30
E02F 10 Code Design
E02H 20
E02K 30 C a 0 b
B31F QB = QA /2 10 / 5
B31H 20 / 10
B31K 30 / 15 E a 0
B32F QB = QA /2 10 / 5
B32H 20 / 10
B32K 30 / 15 K 0 b

Short delivery time

for all variations

1) Please order connector separately, see chapter 3 accessories.

2) Not for spool/sleeve design.

D1FB UK.indd 25.03.24

3-4 Parker Hannifin Corporation

Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Ordering Code Series D1FB OBE

D1FB OBE (with onboard electronics)

D 1 F B 0 N
Directional Size Proportional Standard Spool Spool Seals NBR Input Options Design Design
control DIN NG06 control dynamics type position (other seal signal series
valve CETOP 03 standard compounds (not required
on request) for ordering)
NFPA D03 repeatability

D1FB*0: Spool/sleeve design

Flow [l/min]
Code Design
Spool/sleeve
3
Code Spool type at Dp 5 bar 0
design
per metering edge 3 Spool/body design
Overlap
E01C A B 6
E01F 12
E01H P T 20 Code Input signal 2) Function Port Options
E02C 6 Potentiometer
E02F 12 F0 0...+/-10 V 0...+10 V > P-A 6 + PE
supply
E02H 20 G0 0...+/-20 mA 0...+20 mA > P-A 6 + PE —
E03C 6
S0 4...20 mA 12...20 mA > P-A 6 + PE —
E03F 12
E03H 20 Command
0...+/-10 V 0...+10 V > P-A channel &
QB = QA /2 W5 1) 11 + PE
B31F 12 / 6 4...20 mA 12...20 mA > P-A potentiometer
B31H 20 / 10 supply
QB = QA /2
B32F 12 / 6
B32H 20 / 10

D1FB*3: Spool/body design Code Design

Flow [l/min]
Code Spool type at Dp 5 bar C a 0 b
per metering edge
Overlap
E01F A B 10 E a 0
E01H 20
E01K P T 30
E02F 10 K 0 b
E02H 20
E02K 30
B31F QB = QA /2 10 / 5
B31H 20 / 10
B31K 30 / 15
B32F QB = QA /2 10 / 5 Please order connector separately, see chapter 3 ac-
B32H 20 / 10 cessories.
B32K 30 / 15
Parametrizing cable OBE® RS232: Item no. 40982923

Short delivery time

for all variations

1) Factory set ± 10 V on delivery.

2) Single solenoid always 0...+10 V respectively 4...20 mA.

D1FB UK.indd 25.03.24

3-5 Parker Hannifin Corporation

 Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Technical Data Series D1FB

General
Design Direct operated proportional DC valve
Actuation Proportional solenoid
Size NG06/CETOP 03/NFPA D03
Mounting interface DIN 24340 / ISO 4401 / CETOP RP121 / NFPA
Mounting position unrestricted
Ambient temperature [°C] -20...+60
MTTFD value 1) [years] 150
Weight (OBE) [kg] 2.2 (2.9)
Hydraulic
3 Max. operating pressure
Max. pressure drop PABT / PBAT
[bar] Ports P, A, B 350; Port T 210
[bar] 350
Fluid Hydraulic oil according to DIN 51524 ... 535, other on request
Fluid temperature [°C] -25...+60
Viscosity permitted [cSt] / [mm2/s] 20...400
recommended [cSt] / [mm2/s] 30...80
Filtration ISO 4406; 18/16/13
D1FB*0 (Spool/sleeve) D1FB*3 (Spool/body)
Nominal flow at ∆p = 5 bar
per control edge 2) [l/min] 6/12/20 10/20/30
Leakage at 100 bar [ml/min] <50 <60
Opening point (OBE) [%] see flow characteristics (set to 10 command signal)
Static / Dynamic
Step response at 100 % step [ms] 30 30
Hysteresis [%] <4 <6
Temperature drift solenoid current [%/K] <0.02
Electrical characteristics
Duty ratio [%] 100 ED; CAUTION: Coil temperature up to 150 °C possible
Standard (as per EN 175301-803) IP65 in accordance with EN 60529 (with correctly mounted
Protection class plug-in connector)
DT04-2P “Deutsch“ IP69K (with correctly mounted plug-in connector)
Code "J"
Solenoid Code "M" Code "K"
(Spool/sleeve)
Supply voltage [V] 9 12 24
Current consumption [A] 2.7 2.2 1.1 (0.8)
Resistance [Ohm] 2.7 4.4 18.6
Connector as per EN 175301-803 (code W), DT04-2P “Deutsch“ connector (code J).
Solenoid connection
Solenoid identification as per ISO 9461.
Wiring min. [mm²] 3x1.5 (AWG 16) overall braid shield (Code W), "Deutsch" connector DP4 2-Pin (Code J)
Wiring lenght max. [m] 50

1) If valves with onboard electronics are used in safety-related parts of control systems, in case the safety function is requested, the valve elec-
tronics voltage supply is to be switched off by a suitable switching element with sufficient reliability.

√
2)
Flow rate for different ∆p per control edge: Qx = QNom. · ∆px
∆pNom.

D1FB UK.indd 25.03.24

3-6 Parker Hannifin Corporation

Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Technical Data Series D1FB OBE

Electrical characteristics OBE

Vibration resistance [g] 10 Sinus 5...2000 Hz acc. IEC 68-2-6
10 (RMS) Random noise 20...2000 Hz acc. IEC 68-2-36
15 Shock acc. IEC 68-2-27
Duty ratio [%] 100 ED; CAUTION: Coil temperature up to 150 °C possible
Protection class IP65 in accordance with EN 60529 (with correctly mounted plug-in connector)
Supply voltage/ripple DC [V] 18...30, ripple < 5 % eff., surge free
Current consumption max. [A] 2.0
Pre fusing medium lag [A] 2.5
Input signal
Codes F0 & W5 voltage
Codes S0 & W5 current
[V] +10...0...-10, ripple < 0.01 % eff., surge free, Ri = 100 kOhm, 0...+10 V → P -> A
[mA] 4...12...20, ripple < 0.01 % eff., surge free, Ri = <250 Ohm, 12...20 mA → P -> A 3
< 3.6 mA = enable off,
> 3.8 mA = enable on (acc. to NAMUR NE43)
Code G0 [mA] +20...0...-20, ripple < 0.01 % eff., surge free, Ri = <250 Ohm, 0...+20 mA → P -> A
Differential input max.
Codes F0, G0 & S0 [V] 30 for terminal D and E against PE (terminal G)
11 for terminal D and E against 0V (terminal B)
Code W5 [V] 30 for terminal 4 and 5 against PE (terminal PE)
11 for terminal 4 and 5 against 0V (terminal 2)
Channel recall signal [V] 0...2.5: off / 5...30: on / Ri = 100 kOhm
Adjustment ranges Min [%] 0...50
Max [%] 50...100
Ramp [s] 0...32.5
Interface RS 232, parametrizing connection 5pole
EMC EN 61000-6-2, EN 61000-6-4
Central connection
Codes F0, G0 & S0 6 + PE acc. to EN 175201-804
Code W5 11 + PE acc. to EN 175201-804
Wiring min.
Codes F0, G0 & S0 [mm²] 7 x 1.0 (AWG16) overall braid shield
Code W5 [mm²] 11 x 1.0 (AWG16) overall braid shield
Wiring length max. 50

D1FB UK.indd 25.03.24

3-7 Parker Hannifin Corporation

 Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Characteristic Curves Series D1FB / D1FB OBE

Flow characteristics
D1FB*0 external electronics
at ∆p = 5 bar per metering edge
Spool type E01/02/03, B31/32
100 100
Flow Q [% of nominal flow]

Flow Q [% of nominal flow]

Spool type E* Spool type B*

75 75
A-T P-A

3
50 50

P-B P-A
A-T B-T P-B B-T
25 25

0 0
100 -80 -60 -40 -20 0 20 40 60 80 100 100 -80 -60 -40 -20 0 20 40 60 80 100
Command signal [%] Command signal [%]

D1FB*0 OBE
(set to opening point 10 %)
at ∆p = 5 bar per metering edge
Spool type E01/02/03, B31/32
100 100
Flow Q [% of nominal flow]

Flow Q [% of nominal flow]

Spool type E* Spool type B*

75 75
A-T P-A

50 50

P-B P-A
A-T B-T P-B B-T
25 25

0 0
100 -80 -60 -40 -20 0 20 40 60 80 100 100 -80 -60 -40 -20 0 20 40 60 80 100
Command signal [%] Command signal [%]

Functional limits
at 25 %, 50 %, 75 % and 100 % command signal At asymmetric flow a reduced flow limit has to be con-
(symmetric flow) sidered.
Spool type E01H
40
Flow Q [l/min]

A B

100 %
30 P T

75 %
20

10 50 %

25 %
0
0 50 100 150 200 250 300 350
Pressure drop p P–T [bar]

All characteristic curves measured with HLP46 at 50 °C.

D1FB UK.indd 25.03.24

3-8 Parker Hannifin Corporation

Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Characteristic Curves Series D1FB / D1FB OBE

Flow characteristics
D1FB*3 external electronics
at ∆p = 5 bar per metering edge
Spool type E01/02/03, B31/32
100 100
Flow Q [% of nominal flow]

Flow Q [% of nominal flow]

Spool type E* Spool type B*

75 75

A-T P-A
50
P-B
A-T
P-A
B-T
50
3
P-B B-T
25 25

0 0
100 -80 -60 -40 -20 0 20 40 60 80 100 100 -80 -60 -40 -20 0 20 40 60 80 100
Command signal [%] Command signal [%]

D1FB*3 OBE
(set to opening point 10 %)
at ∆p = 5 bar per metering edge
Spool type E01/02
100 100
Flow Q [% of nominal flow]

Flow Q [% of nominal flow]

Spool type E* Spool type B*

75 75

P-B P-A
A-T B-T A-T P-A
50 50

P-B B-T
25 25

0 0
-100 -80 -60 -40 -20 0 20 40 60 80 100 -100 -80 -60 -40 -20 0 20 40 60 80 100
Command signal [%] Command signal [%]

Functional limits
at 25 %, 50 %, 75 % and 100 % command signal At asymmetric flow a reduced flow limit has to be con-
(symmetric flow) sidered.
Spool type E01K
70
Flow Q [l/min]

A B
60

50 P T

40
100 %
30
75 %
20

10 50 %
25 %
0
0 50 100 150 200 250 300 350
Pressure drop p P–T [bar]

All characteristic curves measured with HLP46 at 50 °C.

D1FB UK.indd 25.03.24

3-9 Parker Hannifin Corporation

 Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Block Diagrams Series D1FB OBE

Code F0 Code G0, S0

6 + PE acc. to EN 175201-804 6 + PE acc. to EN 175201-804

Reference Reference
command E command E
F0: 0...+/-10 V µC G0: 0...±20 mA µC
D S0: 4...12...20 mA D
potentiometer-
supply

3
+10 V C
-10 V F

0V 0V
G A B G A B
supply supply
PE voltage PE voltage
18...30 V= 18...30 V=

Code W5
11 + PE acc. to EN 175201-804
preset
recall
S1 S2 S3 S4
6 7 8 11

Reference
command 5
W5: 0...+/-10 V µC
4
potentiometer-
supply
+10 V 9
-10 V 10

0V
4
5
3 10 6
1 2
2 9 11 7
supply
1 8 voltage
PE
18...30 V=

D1FB UK.indd 25.03.24

3-10 Parker Hannifin Corporation

Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Interface Program Series D1FB OBE

ProPxD interface program Features

The ProPxD software permits comfortable parameter • Comfortable editing of all parameters
setting for the module electronics. Via the clearly arranged • Depiction and documentation of parameter sets
entry mask the parameters can be noticed and modified. • Storage and loading of optimized parameter adjust-
Storage of complete parameter sets is possible as well ments
as printout or record as a text file for further documenta- • Executable with all actual Windows® operating
tion. Stored parameter sets may be loaded anytime and systems from Windows® XP upwards
transmitted to other valves. Inside the electronics a non-
• Plain communication between PC and electronics
volatile memory stores the data with the option for recall-
via serial interface RS232C
ing or modification.
The PC software can be downloaded free of charge at
The parametrizing cable may be ordered under 3
item no. 40982923.
www.parker.com/isde – see page “Support" or directly at
www.parker.com/propxd.

D1FB UK.indd 25.03.24

3-11 Parker Hannifin Corporation

 Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Dimensions Series D1FB

D1FB*C

15
79.5
Ø9.5

22
P
Ø5.5

3 P

46
A B
T

72.5 17
222

D1FB*E D1FB*K
15

15
79.5

79.5
Ø9.5 Ø9.5
~53

~53
22

22
P P
Ø5.5 Ø5.5

P P
46

46

A B A B
T T

72.5 17 17 132
158 158

D1FB*C*0 with DT04-2P "Deutsch" connector D1FB*C*3

(only C style shown)

Ø9.5
71.3
68

22

P
Ø5.5

P
46

A B
T

72.5 17
222

Surface finish Kit

NBR
0.01/100 4x M5x30 7.6 Nm
Rmax6.3 BK375 SK-D1FB
ISO 4762-12.9 ±15 %

D1FB UK.indd 25.03.24

3-12 Parker Hannifin Corporation

Catalogue MSG11-3500/UK Direct Operated Proportional DC Valve
Dimensions Series D1FB OBE

D1FB*C OBE

125
Ø9.5

22
P
Ø5.5

46
A B
T

72.5 17
222

D1FB*E OBE D1FB*K OBE

125

125

Ø9.5 Ø9.5
22

22

P P
Ø5.5 Ø5.5

P P
46

46

A B A B
T T

72.5 17 17 132
158 158

Surface finish Kit

NBR
0.01/100 4x M5x30 7.6 Nm
Rmax6.3 BK375 SK-D1FB
ISO 4762-12.9 ±15 %

D1FB UK.indd 25.03.24

3-13 Parker Hannifin Corporation