Catalog MSG14-2550/US Proportional Directional Control Valves
Technical Information Series D1FP
General Description
Series D1FP direct operated control NG6 (CETOP
3) valve features extremely high dynamics combined
with maximum flow. It is used for high accuracy in
A
positioning of a hydraulic axis, and for controlling force
and velocity.
Driven by the new patented VCD® actuator, the D1FP
reaches the frequency response of servovalves.
Compared with solenoid driven valves, the D1FP can
also be used in applications with pressure drops up to
350 Bar (5075 PSI) across the valve. Because of the
high flow capability the D1FP can be a substitute for
NG10 valves in some cases.
At power-down the spool moves in a defined position.
All common input signals are available.
Features
• Servovalve dynamics: -3dB/350Hz at ±5% input signal
• Full flow capacity up to 350 Bar (5075 PSI) pressure drop
through the valve
• Maximum tank pressure 350 Bar (5075 PSI) with external
drain Y-port
• High flow
• Defined spool positioning in case of loss of electric power
supply
• Onboard electronics
WARNING: This product can expose you to chemicals including Lead, Nickel (Metallic), or 1,3-Butadiene which are known to the State of California to
cause cancer, and Lead or 1,3-Butadiene which is known to the State of California to cause birth defects and other reproductive harm. For more information
go to www.P65Warnings.ca.gov.
A01_Cat2500.indd, ddp, 04/19
A89 Parker Hannifin Corporation
Hydraulic Valve Division
Elyria, Ohio, USA
Catalog MSG14-2550/US Proportional Directional Control Valves
Ordering Information Series D1FP
D 1 F P 9 0
A Directional Size
Control Valve DIN NG6
CETOP 3
Proportional
Control
VCD Spool
Type
Spool
Position
on Power
Y-Port
Plugged 4)
Seal Input
Signal
Options Spool/
Sleeve
Design
Design
Series
NOTE:
NFPA D03 Down 1) Not required
when ordering.
Flow LPM (GPM) Code Description Code Description
Code Spool at ∆p 35 Bar (508 PSI) N Nitrile 0 6 + PE acc. EN175201-804
per metering edge 5 11 + PE acc. EN175201-804
V Fluorocarbon
Zerolap 7 6 + PE + Enable
H For HFC Fluid
E50M* 40 (10.6)
E50H 25 (6.6)
E50G 16 (4.2) Spool Position Code Signal Flow Direction 5)
Code
E50F 12 (3.2) on Power Down B +/- 10V 0...+10V -> P-A
E50C 6 (1.6)
E +/- 20mA 0...+20mA -> P-A
E50B 3 (0.8)
A 2) S 4...20mA 12...20mA -> P-A
B60M* 40 (10.6) / 20 (5.3)
B60H QB = QA /2 25 (6.6) / 12.5 (3.3)
B60G 16 (4.2) / 8 (2.1)
B60F 12 (3.2) / 6 (1.6)
B60C 6 (1.6) / 3 (0.8) B 2)
Underlap approximately -0.5%
E55M* 40 (10.6)
E55H 25 (6.6)
C 3)
E55G 16 (4.2)
E55F 12 (3.2)
E55C 6 (1.6) A B
E55B 3 (0.8)
H 6) a 0 b
Overlap 25%
P T
E01M* 40 (10.6)
E01H 25 (6.6) A B
E01G 16 (4.2)
J 6) a 0 b
E01F 12 (3.2)
E01C 6 (1.6) P T
E01B 3 (0.8)
B31M* 40 (10.6) / 20 (5.3)
B31H QB = QA /2 25 (6.6) / 12.5 (3.3)
B31G 16 (4.2) / 8 (2.1) 1)
On power down the spool moves in a defined position. This cannot
B31F 12 (3.2) / 6 (1.6) be guaranteed in case of single flow path on the control edge
B31C 6 (1.6) / 3 (0.8) A→ T resp. B→ T with pressure drops above 120 Bar (1740 PSI)
E02M* 40 (10.6) or contamination in the hydraulic fluid.
E02H 25 (6.6) 2)
Approximately 10% opening, only available with zerolap spools and
E02G 16 (4.2) underlap spools.
E02F 12 (3.2) 3)
Only available with overlap spools.
E02C 6 (1.6) 4)
Needs to be removed at tank pressure >35 Bar (507.5 PSI).
E02B 3 (0.8) 5)
Flow direction P→ A with Pin D > Pin E.
B32M* 40 (10.6) / 20 (5.3)
QB = QA /2
6)
Not for flow code M.
B32H 25 (6.6) / 12.5 (3.3)
B32G 16 (4.2) / 8 (2.1)
B32F 12 (3.2) / 6 (1.6)
B32C 6 (1.6) / 3 (0.8)
Bolt Kit:
* Flow is 32 (8.5) when spool power down BK209 (4) 10-24x1.25
options H or J are used. BK375 (4) M5x30
Please order plugs separately. See Accessories. Weight: 5.0 kg (11.0 lbs.)
A01_Cat2550.indd, ddp, 03/20
A90 Parker Hannifin Corporation
Hydraulic Valve Division
Elyria, Ohio, USA
Catalog MSG14-2550/US Proportional Directional Control Valves
Specifications Series D1FP
General
Design Direct operated proportional DC valve
Actuation
Size
Mounting Interface
VCD® actuator
NG6 / CETOP 3 / NFPA D03
DIN 24340 / ISO 4401 / CETOP RP121 / NFPA
A
Mounting Position Unrestricted
Ambient Temperature [°C] -20...+50; (-4°F...+122°F)
MTTFD Value [years] 75
Vibration Resistance [g] 10 Sinus 5...2000 Hz acc. IEC 68-2-6
30 Random noise 20...2000 Hz acc. IEC 68-2-36
15 Shock acc. IEC 68-2-27
Hydraulic
Maximum Operating Pressure Ports P, A, B 350 Bar (5075 PSI)
Port T max. 35 Bar (508 PSI), port Y max. 35 Bar (508 PSI) 1)
Fluid Hydraulic oil as per DIN 51524...51535, other on request
Fluid Temperature [°C] -20...+60; (-4°F...+140°F)
Viscosity
Permitted [cSt] / [mm2/s] 20...380 (93...1761 SSU)
Recommended [cSt] / [mm2/s] 30...80 (139...371 SSU)
Filtration ISO 4406 (1999) 18/16/13 (acc. NAS 1638: 7)
Nominal Flow at
[LPM] 3 LPM (0.08 GPM) / 6 LPM (1.6 GPM) / 12 LPM (3.2 GPM) / 25 LPM (6.6 GPM) /
∆p=35 Bar (508 PSI)
[LPM] 40 LPM (10.6 GPM)
per Control Edge 2)
Flow Maximum 90 LPM (23.8 GPM) at ∆p=350 Bar (5075 PSI) over two control edges
[ml/
Leakage at 100 Bar (1450 PSI) <400 (zerolapped spool); <50 (overlapped spool)
min]
Static / Dynamic
Step Response at 100% Step 3) [ms] <3.5
Frequency Response
(±5% signal) 3) [Hz] 350 (amplitude ratio -3dB), 350 (phase lag -90°)
Hysteresis [%] <0.05
Sensitivity [%] <0.03
Temperature Drift [%/K] <0.025
Electrical
Duty Ratio [%] 100 ED; CAUTION: Coil temperature up to 150°C (302°F) possible
Protection Class IP65 in accordance with EN 60529 (plugged and mounted)
Supply Voltage/Ripple [V] DC 22 ... 30, ripple <5% eff., surge free
Current Consumption Maximum [A] 3.5
Pre-Fusing [A] 4.0 medium lag
Input Signal
Voltage [V] 10...0...-10, ripple <0.01% eff., surge free, 0...+10V P->A
Impedance [kOhm] 100
Current [mA] 20...0...-20, ripple <0.01% eff., surge free, 0...+20mA P->A
Impedance [Ohm] 250
Current [mA] 4...12...20, ripple <0.01% eff., surge free, 12...20mA P->A
<3.6 mA = disable, >3.8 mA = according to NAMUR NE43
Impedance [Ohm] 250
Differential Input Maximum
Code 0 [V] 30 for terminal D and E against PE (terminal G)
Code 5 / 7 [V] 30 for terminal 4 and 5 against PE (terminal W )
Enable Signal (Only Code 5 / 7) [V] 5...30, Ri = 9 kOhm
Diagnostic Signal [V] +10...0...-10 / +Ub, rated max. 5mA
EMC EN61000-6-2 / EN61000-6-4
Electrical Connection Code 0 6 + PE acc. EN 175201-804
Code 5 11 + PE acc. EN 175201-804
Code 7 6 + PE + Enable
Wiring Miniimum
Code 0 [mm²] 7x1.0 (AWG 18) overall braid shield
Code 5 [mm²] 12x1.0 (AWG 20) overall braid shield
Code 7 [mm²] 12x1.0 (AWG 18) overall braid shield
Wiring Length Maximum [m] 50 (164 ft.)
For applications with pT>35 Bar (508 PSI) the Y-port has to be connected and the plug in the Y-port has to be removed.
1)
√
Flow rate for different ∆p per control edge: Qx = QNom. ·
2)
∆px 3)
Measured with load 100 Bar (1450 PSI)
∆pNom. pressure drop/two control edges.
A01_Cat2500.indd, ddp, 04/19
A91 Parker Hannifin Corporation
Hydraulic Valve Division
Elyria, Ohio, USA
Catalog MSG14-2550/US Proportional Directional Control Valves
Performance Curves Series D1FP
Spool Type E01/E50
Spool Type B60
A01_Cat2500.indd, ddp, 04/19
A92 Parker Hannifin Corporation
Hydraulic Valve Division
Elyria, Ohio, USA
Catalog MSG14-2550/US Proportional Directional Control Valves
Block Diagrams — Wiring Series D1FP
Code 0 Code 5
6 + PE acc. to EN 175201-804 11 + PE acc. to EN 175201-804
Enable
+5...30V
A
8 3
Zero position Zero position
Command Command
E 5
0...±10V PID 0...±10V PID
0...±20mA 0...±20mA
4...20mA D 4...20mA 4
Diagnostic F Diagnostic 6
spool stroke U I spool stroke U I
0 0
0...±10V C 0...±10V 7
0 n. c. 0
G A B 9 11 10 1 2
Supply Supply
A 4 5 PE voltage
F B PE voltage
3 10 6
G 22...30V= 22...30V=
E C 2 9 11 7
D 1 8
Note: When replacing another valve, verify Pin C is 0 V and not wired as an enable.
Code 7
6 + PE + Enable acc. to EN 175201-804
A01_Cat2500.indd, ddp, 04/19
A93 Parker Hannifin Corporation
Hydraulic Valve Division
Elyria, Ohio, USA
Catalog MSG14-2550/US Proportional Directional Control Valves
Dimensions Series D1FP
Inch equivalents for millimeter dimensions are shown in (**)
Surface Finish Seal
BK375 4x M5x30 7.6 Nm (5.6 lb.-ft.) Nitrile: SK-D1FP
DIN 912 12.9 ±15 % Fluorocarbon: SK-D1FP-V
BK209 4x 10-24x1.25 for HFC Fluid: SK-D1FP-H
A01_Cat2500.indd, ddp, 04/19
A94 Parker Hannifin Corporation
Hydraulic Valve Division
Elyria, Ohio, USA
