SPEC, SHEET No, TM+292-4-007/EX-O1 [TM-ZR296 ] SPEC, SHEET No, TM+292-4-307/EX-O1 [TM+ZR296(H) J DATE August, 1999 TADANO CARGO CRANE MODEL: [] TM-zR296 (CO TM-zZR296 (H) with hook stowing device CRANE SPECIFICATIONS CRANE CAPACITY 3,030 kg at 1.45 m (4-part lines) BOOM @sectioned, fully powered partly synchronized telescoping boom of pentagonal box construction Retracted length......3.23 m 12.8 0 -9.57 m/ 17s oe hydraulic cylinder -' to 76° / 6.05 Extended length. ... Extending speed. Elevation ... evated by a double-acting Elevating speed. Boom point. -2 sheaves WINCH Hydraulic motor driven Spur gear speed reduction, provided with mechanical brake and cable follower «7.45 KN(760 kgf} Single line speed.....66 m/min (at 4th layer) Single line pull. . Wire rope diameter X length. ... 8 nm x 75m breaking strength. ..43.1 kN(4.39 tf} TXT +6 X WwS(26) construction. Hook block. HOOK STOWING DEVICE M-ZR296 (H). only] Mechanically stowed beneath boom top portionge iS OUTRIGGERS I-007/EX-O1 [TMHZR296) I-307/EX-O1 [TMHZR296 (1) ] Hydraulic motor driven Worm gear speed reduction Continuous 360° full circle swing on ball bearing slew ring Automatic swing lock Si ing speed ~ 2.5 min {rpmt Manual ly extended sliders and hydraulically extended jacks Integral with crane frame — Power up and down REAR OUTRIGGERS (Locally provided) HYDRAULICS, SAPETY DEVICES. CRANE MASS: NOTE. Extended width ~~ Min, 1,720 mm Mid, 2,400 mm, 2,900 mm Max. 3,400 mm Fully extended width —-- Not less than 2,400 om Hydraulic pump ~ - Single gear pump Hydraulic motors Axial piston type for winch Axial piston type for swing Control valves Multiple control valves with integral safety valve Load meter Load indicator Over-winding alarm Hoisting limiter [TM-2R296 (1) only] P.T.0 indicator lamp Hook safety latch Level gauge Hydraulic safety valves, check valves and holding valves Approx. 1,180 kg (with standardized mounting parts included and rear outriggers excluded) Operating speeds of the crane are guaranteed under the condition that the pump delivery is 53 L/min,‘SPEC, SHEBT No, TH+297- ‘SPEC, SHEET No, Ti -007/BX-01 (EZ 307/EX-O1 (TE: 196) 296 (1) ] RATED LIFTING CAPACITIES IN KIROGRAMS 7] iae ¥ 7 7 : an lae aia |p aoa] S 2.89 ro 30 | 22 308 108 and below |_%03 | and betor |_1-79° | and below | 99° | and below baad Zoe [oi] 250 | 50) 35m 450 TA Za] 1730] 308 | 1250} 4.00 3.0 210) S00 | 1-430] 350 | 1,080) 5.08 60 180 350 | 1230] 40-8 930] 6.0m 0a 160 40a | 1030 | 458 30_[ 7.0m 0m 140 250 60 3.0-8 730 8.0m 9.0m 130 497m 750] 5.5.8 @a0| 8.8m 10.0-m 100 60m 600, 0.7m 698 430) A: Boom length B: Load radius 1, The mass of the hook (30 kg), slings and all similarly used load handling devices 2, The above numerical values of rated lifting e: based on crane strength only. The rated lifting capacities based on stability may lower than those in the above table depending on the loading conditions and the types of the chassis.14 4 r 1-007/EX-O1 [TMHZR296] 297-~307/EX-01 [TM~ZR296 (H) ] ‘SPBC, SHEBT No. ‘SPEC, SHEBT No. WORKING RANGE q fe NOTE: /O o Bae NP £10} EROS £ & La) PNP. qd 8 Nes TE 0. r 6 u Ofe s ' Ly \ A Se bl a 01234567 87101112131415 RADIUS (m) The above lifting heights and boom angles are based on a straight (unladen) boom, and allowance should be made for boom deflection obtained under Laden condi tions.007/EX-O1 [TM+ZR296] 307/EX-O1 [TM+ZR296 (H) ] DIMENSIONS ZR296 | wheh Jace eo ed bas tied. cna ZR296 (H) ww il Beier azo‘SPBC, SHEET No, TAH2! ‘SPEC, SHEET No, Ti 74-007/EX-O1 [TN+ZR296] I-307/EX-O1 [TMHZR296 (1) ] GENERAL DATA FOR SUITABLE TRUCKS Gross vehi mass (including crane mass) 4,000 to 8,000 kg - 108 Nem{11 kgf+m} min, Approx, 300 to 2,500 min {rpm} Approx. 620 nm min, 0. 1.0, Width for crane mounting Frame Weight distribution and frame strength should be calculated for each truck Frame width range (inside to outside) Approx. 650 to 820 mm Frame height (ground to frame top) - Approx. 905 mm max. (eight of crane mounting base can be k floats changed by combination of Jj and crane be