Scribd
Upload
208 views2 pages

RE-717MC Instruction Manual

This document provides installation and maintenance instructions for the RE-717MC Control Module from Ravel Electronics. It includes specifications such as operating voltage, current draw, and environmental conditions, as well as general installation guidelines and wiring configurations. The module is designed for use in intelligent two-wire systems and must be connected to compatible control panels while adhering to local codes and regulations.

Uploaded by

mohamedaamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
208 views2 pages

RE-717MC Instruction Manual

This document provides installation and maintenance instructions for the RE-717MC Control Module from Ravel Electronics. It includes specifications such as operating voltage, current draw, and environmental conditions, as well as general installation guidelines and wiring configurations. The module is designed for use in intelligent two-wire systems and must be connected to compatible control panels while adhering to local codes and regulations.

Uploaded by

mohamedaamer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

INSTALLATION AND MAINTENANCE INSTRUCTIONS

Reliabilityatreach
RAVEL ELECTRONICS PVT LTD.,
P38/3, Central Avenue, Mahindra World City, Anjur,
Chengalpattu Taluk, Kanchipuram - 603004 .India.
Ph.: +91-44-2496 1004 / 0825. Fax: +91-44-4204 9599.
E-Mail: marketing@ravelfire.com; www.ravelfire.com
RE-717MC CONTROL MODULE

SPECIFICATION
Operating Voltage : 24 VDC Nominal.
Current Draw : 2 mA Max.(Latched)
Standby Current : 0.5 mA, 47K EOL.
Line Loss : 4 VDC Max.
External Supply Voltage : Regulated 24V.
Max. Output Current Drive : 1 Amps.(Supervised)
o o .
Temperature Range : 0 C to 49 C
Humidity : 10% to 93% Non - condensing.
Dimensions : 95 mm x 75 mm x 24mm (L x B x H)

Before Installation:
This instruction manual is about quick reference installation guide. For
detailed system information refer the control panel installation manual.
Inform to the operator and authority person that system will be temporarily
out of service, while the module is installed in the existing system.

Note:
Disconnect the power to the control panel before installing the module.

General Instruction:
This control module is intended for the use in intelligent two wire system.
The individual address of the each module is selected by using the DIP
Switch. This module is used to switch the given external power supply to
the notification appliances. The external power supply may be regulated
DC Supply.
Compatibility Requirement:
This control module should be connected to listed compatible control panel
only.
NOTE:
All wiring should be conform to applicable local codes, ordinances, and
regulations.
1. Install module wiring in accordance with the job drawings and
appropriate wiring diagrams.
2. Set the address on the module per job drawings.
Wire should be stripped to the appropriate length. Exposed conductor
should be secured under the clamping plate and should not protrude
beyond the terminal block area.
Caution: Do not loop wire under terminals & utilize splice connection.

Wiring Configuration for Notification Appliance Circuits (Class B, Style Y)


24 VDC Power Supply
Regulated, Isolated,
Power Limited as per - To Next 47K EOL
NAC

NAC

NAC

NAC

NFPA 70.
+ Module
-
Resistor
RE-47K
Fire Listed

- To Next
Device
+
SIGNAL LINE
CIRCUIT (SLC)
28 VDC MAX.
-
+
NOTE: From Panel or
Use only Listed Previous Device
* D = NO CONNECTION Compatible Panel

* ALL WIRING SHOWN IS SUPERVISED AND POWER LIMITED Doc.: No.:RE /IIM/ACM V 1.0
Example:

Doc.: No.:RE /IIM/ACM V 1.0

You might also like