Model W2 - Waterproof

Standalone Proximity Reader

User Manual
 1. Packing List
Name Quantity Remark
Waterproof Reader – W2 1
Infrared remote control 1
Manager add card 1
Manager delete card 1
Short Pin 1 Used for factory default setting
User manual 1
Self Tapping Screws 4/2 Φ3.5*27mm

Please ensure that all the above contents are correct. If any are missing please notify the
supplier of the W2.

2. Description
The W2 is fully waterproof stand alone Proximity access Reader, which uses advanced
microprocessor, equipped with large capacity Flash memory, supports up to 10 000 cards. It is
so easy to add or delete card users by using the master card; besides, with infrared remote
control programmer, the user can set the features by themselves, including Alarm,
Self-protection, interlock and Anti-submarine back Function. In additional, with infrared remote
control programmer, you can add or delete cards directly by inputting card number

The W2 not only has the features of low power consumption, automatic selection of lock ,anti
vandal alarm and exit button, but also has the protective functions against input over voltage
and outputs short-circuit. These features make the W2 easy in operation, safe and reliable; it is
an idea choice for door access.

3. Features

z Standalone Card Reader

z Waterproof, confirm to IP68
z Use capacity: 10,000
z Card interface: 125KHZ EM card
z Remote control for programming
z With Manager cards for fast add and delete users
z Wiegand26 input/output
z Can be used as salve reader
z 2 pcsW2 can be interconnected/ interlocked
z Can be used as controller by connection slave reader
z Anti-submarine back Function
z Alarm signal output, Door open detection
z LED display; Full of 10000 users, recognizing speed <15ms.

2
 4. Specifications
Supply Voltage DC12V±10%
User capacity 10,000
Sleeping Current <15mA
Card type 125KHZ EM card
Card Reading Distance
5ᨺ10cm

Wiegand interface Wiegand 26

Operating Temperature
-25ᨺ60Ԩ

Operating Humidity
20%ᨺ98%

Environment Confirm to IP68

Lock output load Max20A
Alarm output load Max20A
Adjustable Door Relay Time 00-99 seconds
Adjustable Alarm Time 0- 3 minutes
Wiring Connections Electric Lock, Exit Button, DOTL, External Alarm
Manager card Two
Dimensions 103*48*23mm

5. Installation
z Drill holes on the wall or prepare the cassette.
z Wire through the hole, and blanket the unused cable in case of short circuit.
z Fix the back cover firmly on the cassette or the wall.
z Attach the reader to the back cover.

 

3
6. Wiring
No Color Function Description

1 D0 Wiegand output, input signal wire D0

Green
2 White D1 Wiegand output, input signal wire D1

3 Grey ALARM+ connecting to the negative pole of the alarm equipment

4 OPEN To connect to one part of Exit Button

Yellow
5 Brown D_IN Door Contact input,

6 Red 12V (+) 12Vdc Positive Regulated Power Input

7 GND (-) Negative Regulated Power Input

Black
the negative pole of the controller, connect to the other part of Exit
8 Blue VSS
button and door contact

9 L- Connect to the negative pole of the Lock

Purple

10 Connect to the positive pole of the lock and alarm equipment

Orange L+/Alarm+

Connection Diagram

4
 7. Interface Circuits

Figure 1
Note: The above diagrams show the output interface circuits. Do not power on until all wiring
has been completed

8. To Reset to Factory Default

Power off, use the supplied Contact Pin to short out the 2P socket on the main board, then
power on, if successful, the beeper will beep twice, the LED shines in orange, remove the
Short Pin, then read any two EM cards, after that the LED turns in red, means reset to factory
default setting successfully. Of the two EM cards read, the first one is Manager add card, the
second one is Manager delete card.
Remarks: Reset to factory default setting, the users' information enrolled is still retained. When
reset to Factory setting, the two Manager cards must be re-enrolled.

9. Sound and Light indication

Operation status LED Buzzer
Reset to factory default setting Orange Two short ring
Sleeping mode Red shines slow
Operation successful Short ring
Enter into programming mode Red shines Short ring
Enter into setting Orange shines Short ring
Exist from programming mode Red shines slow Short ring
Operation failed Three short ring
Open the door Green shines Short ring
Alarm Red shines fast Alarm

5
 10. W2 Detailed Programming Guide
10.1 User settings
There are 2 ways to add and delete users:
A - By manager card; B - By remote control
A - By Manager card(The most convenient way)
To Add user by Manager Add Card Manager add card Read card Manager add
card Cards can be added continuously.
To Delete User by Manager Delete Card Manager delete card Read Card Manager
delete card Cards can be deleted continuously.
B- By Remote control
Enter into the programming mode firstly
To Enter the programming mode * Manager Password #
888888 is the default factory master code
Remarks: All the steps below must be done after enter into programming mode
To change the master code 0 New Password # Repeat New Password #

The master code must be 6ᨺ8 digit number.

To add a card user (Method 1) 1 Read Card # or

This is the faster way to enter cards using ID 1 Input Card number (8 digit) #
number auto generation. The card can be Card can be added continuously without exiting
either be presented or input the 8 digit card programming mode.
number from the card can be manually The card number is the last 8 digits of the number
entered printing on the card.
To add a card user(Method 2) 1 ID number # Read Card # or
This is the alternative way to enter cards 1 ID number # the Card number (8 digits) #
using User ID Allocation. In this method a
User ID is allocated to a card. Only one user
ID can be allocated to a single card.
To delete a card user by card Number. 2 Read Card # or
Note users can be deleted continuously 2 Card number #
without exiting programming mode
To delete ALL users. 2 0000 #
(Note: This option will delete all users but
Manager Cards. Be careful with use)

10.2 Door setting

Lock power setting
Fail secure (Unlocked when power on)
4 0ᨺ99 #

0-99 is to set the door relay time 0-99 seconds.

6
Fail safe (unlocked when power is off)
5 0ᨺ99 #
This is the factory default, 3 seconds.
0-99 is to set the door relay time 0-99 seconds.
Anti-submarine Settings
Anti-submarine Disabled (Factory default)
Anti-submarine Master Mode: 3 0 #
Anti-submarine Auxiliary Machinery Mode 3 1 #
(Note: the detailed wiring diagram and 3 2 #
illustrate ,please refer to the “Advanced
application”
Door open detection
Door Open Too Long (DOTL) warning. When used with an optional magnetic
contact or built-in magnetic contact of the lock, if the door is opened normally, but
not closed after 1 minute, the inside buzzer will beep automatically to remind
people to close the door and continue for 1 minute before switching off
automatically.
Door Forced Open warning. When used with an optional magnetic contact or built in
magnetic contact of the lock, if the door is forced open, or if the door is opened
after 120 seconds of the electro-mechanical lock not closed properly, the inside
buzzer and alarm output will both operate.
To disable door open detection. 6 0 #
(Factory default)
To enable door open detection 6 1 #
Security Mode Setting
Reader Lockout & Alarm Output options. If there are 10 invalid cards or 10 incorrect
PIN numbers in a 10 minute period either the reader will lockout for 10 minutes or the
alarm will operate for 10 minutes, depending on the option selected below.
Normal status (No lockout or Alarm) 7 0 # (Factory default setting)
Keypad Lockout 7 1 #
Alarm Output 7 2 #
Door Interlock.
Door interlock disabled 8 0 # (Factory default setting)
Door interlock enabled 8 1 #
Alarm output time
To set the alarm output time (0-3
9 0ᨺ3 #
minutes) Factory default is 1 minute

To remove the alarm

To remove the Door Forced Open warning Read valid card or Master Code#
To remove the Door Open Too Long Close the door or Read valid card or Master Code #
warning
To Unlock the door
To Unlock the door Read User card (Note that Manager Card can’t
be used as User Card to unlock the door.)

7
 Attach: Advanced Application

1. W2 operating as a Controller
In this mode the W2 supports a Wiegand 26 bit input so an external Wiegand device
with a 26 bit output can be connected to the Wiegand input terminals on the W2. Either
an ID card reader (125 KHZ) or an IC card reader (13.56MHZ) can be connected to the
W2. Cards are required to be added at the external reader, except where an external
EM reader is used, in this case cards can be added at either reader. See figure 1

Figure 1

2 W1 operating as a Wiegand Output Reader

In this mode the W2 supports a Wiegand 26 bit output so the Wiegand data lines can be
connected to any controller which supports a Wiegand 26 bit input. See figure 2

8
 Figure 2

3, Two W2 units interconnected for a single door

In this mode two W2 units are used for a single door, one for entry and the other for exit.
Either device acts as the controller and reader at the same time. Users can be enrolled on
either of the devices. In this mode the user capacity for one door can be up to 20000. The
setting of the two W2 units must be the same including the master code. See figure 3

Figure 3

4. Two W2 units interconnected & interlocked for 2 doors

In this mode two W2 units are used for a two doors which are then interconnected and
interlocked. In this mode the doors can be interlocked so that when door 1 is open, door
2 cannot be opened, and vise versa. The interlocked function is mainly used in banks,
prisons, and other places where a higher level of security is required. See figure 3

9
 Figure 3

5, Anti-submarine function for single door (3 1 #)

The connection diagram is as figure 1. Install one Wiegand reader (or a W2 without user
information as reader) outside the door, connecting to one W2-Controller inside the door,
which acts as the Anti-submarine Master unit. Of the two devices, they build up an
anti-submarine system for single door. The operation and function is as below:
5.1 Set the needed function and enroll the User Cards on the inside W2 - Anti-submarine
Master unit.
5.2 With the valid user card, the user can only enter the door from the outside reader, and exit
from the inside W2 Controller. On the other hand, without entering record from the reader, the
user can’t exit from the controller inside, also, the user can’t enter in and exit twice
continuously.

6. Anti-submarine function for 2 doors

The connection diagram is as Figure 4. Door 1 with one W2, and Door 2 with one W2, set one
W2 on Door 1 as the Anti-submarine Auxiliary unit (3 2 #), and set the other W2 on Door 2 as
the Anti-submarine Master unit(3 1 #). Then they build up a two doors anti-submarine system,
which is normally used for parking lot…etc

The operation and function is as below:

6.1 Set the needed function and enroll the User Cards from W2 - Anti-submarine Master unit
on Door 2.

6.2 With the valid user card, the user can only enter in from Door 1, and exit from Door 2. On
the other hand, without entering record from the Auxiliary unit, the user can’t exit from the
Master unit or Auxiliary unit, also, the user can’t enter in and exit twice continuously.

10