Terluran GP-35
Acrylonitrile Butadiene Styrene (ABS)
DESCRIPTION
Terluran® GP-35 is high-flow, general purpose injection molding grade with good ductility, intended for moldings with thin walls and/or
adverse flow length to wall ratio.
FEATURES APPLICATIONS
Excellent colorability Injection molding
High flowability Thin wall components for telecommunications
Good impact resistance Household and sanitary appliances
Good heat distortion resistance Toys
High quality surface finish and gloss Automotive components
Great mechanical strength and rigidity Electroplating
Property, Test Condition Standard Unit Values
Rheological Properties
Melt Volume Rate 220 °C/10 kg ISO 1133 cm³/10 min 34
Mechanical Properties
Izod Notched Impact Strength, 23 °C ISO 180/A kJ/m² 22
Izod Notched Impact Strength, -30 °C ISO 180/A kJ/m² 7
Charpy Notched Impact Strength, 23° C ISO 179/1eA kJ/m² 19
Charpy Notched Impact Strength, -30 °C ISO 179/1eA kJ/m² 7
Charpy Unnotched, 23 °C ISO 179/1eU kJ/m² 125
Charpy Unnotched, -30 °C ISO 179/1eU kJ/m² 90
Tensile Stress at Yield, 23 °C ISO 527 MPa 44
Tensile Strain at Yield, 23 °C ISO 527 % 2.4
Tensile Modulus ISO 527 MPa 2300
Nominal Strain at Break, 23 °C ISO 527 % 12
Flexural Strength, 23 °C ISO 178 MPa 65
Hardness, Ball Indentation ISO 2039-1 MPa 99
Thermal Properties
Contact us:
INSTY.infopoint.emea@ineos.com
www.ineos-styrolution.com Page 1 of 3
Revision Date: 08/01/2022
Terluran GP-35
Acrylonitrile Butadiene Styrene (ABS)
Property, Test Condition Standard Unit Values
Vicat Softening Temperature VST/B/50 (50N, 50 °C/h) ISO 306 °C 95
Vicat Softening Temperature, VST/A/50 (10N, 50 °C/h) ISO 306 °C 102
Heat Deflection Temperature A; (annealed 4 h/80 °C; 1.8 MPa) ISO 75 °C 92
Heat Deflection Temperature B; (annealed 4 h/80 °C; 0.45 MPa) ISO 75 °C 95
Coefficient of Linear Thermal Expansion ISO 11359 10-6/°C 80 - 110
Thermal Conductivity ISO 22007-4 W/(m K) 0.17
Electrical Properties
Volume Resistivity IEC 62631-3-1 Ohm*m >1013
Surface Resistivity IEC 62631-3-1 Ohm >1013
Optical Properties
Yellowness Index DIN 6167 - 13
Other Properties
Density ISO 1183 kg/m³ 1040
Water Absorption, Saturated at 23 °C ISO 62 % 0.95
Moisture Absorption, Equilibrium 23 °C/50% RH ISO 62 % 0.24
Processing
Linear Mold Shrinkage ISO 294-4 % 0.4 - 0.7
Melt Temperature Range ISO 294 °C 220 - 260
Mold Temperature Range ISO 294 °C 30 - 80
Injection Velocity ISO 294 mm/s 200
Drying Temperature - °C 80
Drying Time - h 2-4
Typical values for uncolored products
Please note that all processing data stated are only indicative and may vary depending on the individual processing complexities.
Please consult our local sales or technical representatives for details.
SUPPLY FORM
Contact us:
INSTY.infopoint.emea@ineos.com
www.ineos-styrolution.com Page 2 of 3
Revision Date: 08/01/2022
Terluran GP-35
Acrylonitrile Butadiene Styrene (ABS)
Terluran® is delivered as spherical pellets. The bulk density of the pellets is from 0.55 to 0.65 g/cm³. Standard Packaging unit: 25 kg PE-bag
on palette, shrunk or wrapped with PE film or delivery in silo trucks. PE bags should not be stored outside. In dry areas with normal
temperature control, Terluran pellets can be stored for relatively long periods of time without any change in mechanical properties. Under
poor storage conditions, Terluran absorbs moisture, but this can be removed by drying.
PRODUCT SAFETY
No adverse effects on the health of processing personnel have been observed if the products are correctly processed and the production
areas are suitably ventilated. For styrene, acrylonitrile and 1,3-butadiene the maximum allowable workplace concentrations must be
observed according to the pertaining national regulations. In Germany, the following limit values are valid (Oct. 2002): styrene, MAK-value:
20 ml/m³ = 86 mg/m³; acrylonitrile, TRK-value: 3 ml/m³ = 7 mg/m³ and 1,3-butadiene, TRK-value: 5 ml/m³ = 11 mg/m³. According to EU
directive 67/548/EWG, Annex I and TRGS 905 (Oct. 2002), acrylonitrile and 1,3-butadiene are classified as carcinogenic, category 2
(´substances which should be regarded as if they are carcinogenic to man´) and 1 (substances known to be carcinogenic to man),
respectively. Experience has shown that during appropriate processing of Terluran with suitable ventilation the values obtained are well
below the limits mentioned above. TRGS 402 (Germany) can be used for determining and assessing the concentrations of hazardous
substances in the air within working areas. Inhalation of gaseous degradation products, such as those which may arise on severe
overheating of the material or during pumped evacuation, must be avoided. Further information can be found in our Terluran safety data
sheets.
DISCLAIMER
The above mentioned data are accurate to the best of our knowledge. They are based upon reputable labs and industry standard testing
methods. These are only typical values and actual product specification may deviate at industrial range. Therefore, no data in this technical
data sheet shall constitute a warranty or representation regarding product features, fitness of the product for a specific purpose or application
or its processability. INEOS Styrolution disclaims all liability in connection therewith. The customer himself is required to verify whether or not
the product is suitable for the further processing or application intended and whether or not the product complies with the relevant statutory
requirements. Unless explicitly and individually otherwise agreed in writing, INEOS Styrolution's sole and exclusive liability with respect to its
products is set forth in INEOS Styrolution's General Terms and Conditions for Sale.
Contact us:
INSTY.infopoint.emea@ineos.com
www.ineos-styrolution.com Page 3 of 3
Revision Date: 08/01/2022
