Classification: Reference: Date:

AT18-009C NTB18-077C June 22, 2021

MIL ON WITH DTC P0776, P1715

AND MAY HAVE HESITATION AND/OR LACK OF POWER
This bulletin has been amended. See AMENDMENT HISTORY on the last page.
Please discard previous versions of this bulletin.

APPLIED VEHICLES: 2017-2018 Sentra Turbo (B17)

APPLIED ENGINE: MR16DDT

APPLIED TRANSMISSION: CVT (RE0F10D)

IF YOU CONFIRM
The MIL is ON with DTC P0776 (PC SOLENOID B – Pressure Control Solenoid “B”
Performance/Stuck OFF) stored.
NOTE:
 If P0744, P0746, P0841, P0965, P2813, or P17F0 are stored this bulletin does not
apply. Refer to ASIST for diagnostic assistance.
 With this incident, if it should occur, P1715 (INPUT SPEED SENSOR) may be
stored with DTC P0776. The vehicle may also hesitate and/or have reduced power.

ACTION
1. Refer to the Repair Flow Chart on page 2 for mechanical CVT repair.
2. If needed, reprogram the TCM.
 Refer to step 30 in the TCM Reprogramming section (page 21) of the SERVICE
PROCEDURE to confirm if reprogramming is needed.
3. Perform Additional Service (page 19).

IMPORTANT: The purpose of ACTION (above) is to give you a quick idea of the work you
will be performing. You MUST closely follow the entire SERVICE PROCEDURE as it
contains information that is essential to successfully completing this repair.
Nissan Bulletins are intended for use by qualified technicians, not 'do-it-yourselfers'. Qualified technicians are
properly trained individuals who have the equipment, tools, safety instruction, and know-how to do a job
properly and safely. NOTE: If you believe that a described condition may apply to a particular vehicle, DO
NOT assume that it does. See your Nissan dealer to determine if this applies to your vehicle.

1/35
Repair Flow Chart
A.

MIL ON with DTC P0776 stored

NOTE: P1715 may also be stored, and the
vehicle may hesitate
and/or have reduced power

Remove the control

Evidence of valve (valve body), The CVT belt
CVT belt slippage inspect the CVT belt checks out OK

Replace the
CVT assembly
See page 35 Replace the
for important valve body
pre-authorization
information

Reprogram the TCM

(Reprogramming, if needed,
must be done before performing
Additional Service.)

Perform Additional Service

(See page 19)
(Additional Service must be
performed for valve body
replacement or transaxle
replacement.)

2/35 NTB18-077C
SERVICE PROCEDURE

Control Valve (Valve Body) Removal and CVT Belt Inspection

1. Write down all radio station presets.

Presets 1 2 3 4 5 6
AM
FM 1
FM 2
SAT 1
SAT 2/3
Bass Treble Balance Fade Speed Sen. Vol.

2. Disconnect both battery cables, negative cable first.

3. Remove the valve body.

 Before lifting the vehicle, place the transmission gear selector in Neutral.

 For valve body removal, refer to the Electronic Service Manual (ESM), section
TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION > CVT:
RE0F10D > REMOVAL AND INSTALLATION > CONTROL VALVE.

NOTE: The number ‘7’ is on the head of all bolts that need to be removed for valve
body removal. Do not remove any bolt that does not have the number ‘7’.

CAUTION: Never allow any chemicals or fluids other than NS-3 CVT fluid or
equivalent to enter the CVT assembly. Never allow any foreign debris, dust,
dirt, etc. to enter the CVT assembly.

 For additional information, see video # 544: “CVT Belt Inspection”. This video is
located under the TECH TRAINING GARAGE VIDEOS tab in Virtual Academy.

3/35 NTB18-077C
Exploded View

(Total of 9 bolts)

Figure 1
1. Transaxle assembly 2. Terminal cord assembly 3. CVT fluid temperature sensor
bracket
4. Control valve 5. Bracket 6. O-ring
7. New-style oil strainer assembly 8. Old-style oil strainer assembly 9. Oil pan gasket
10. Oil pan 11. Drain plug 12. Drain plug gasket
13. Magnet 14. Spring washer 15. Manual plate
16. Lip seal 17. Snap ring 18. Overflow plug
19. O-ring
: Always replace after every disassembly.
: Nꞏm (kg-m, ft-lb)

: Nꞏm (kg-m, in-lb)

4/35 NTB18-077C
4. Secure the front right tire with a suitable
strap, so it cannot rotate.

 This will assist in making the belt

turn.

5. Mark the front left tire with a suitable

marking.

 This will assure all 360° of the belt is

inspected.

Figure 2

Belt
6. Using borescope J-51951 with its mirror Pulley
attachment, inspect the entirety of the
Case
two sides of the belt that come in contact
with the pulleys (see page 7, Figure 8).
 Reference the Figures on pages 9
through 12 for comparison of an OK
and NG belt condition.
NOTE:
 Be sure to remove the protective film Step 6a
Step 6d
from the mirror before the first use.
 Clean the camera lens and mirror
before each inspection. Use 90% Figure 3
isopropyl alcohol, and a lens swab
from Lens Swab packet J-51963
listed in the PARTS INFORMATION
on page 32.
Camera
 Before inspecting, make sure the flexible tube
camera handle’s AA batteries are
Front
charged and the LCD monitor’s
battery is charged.

a. Insert the camera lens between the

CVT case and pulley where shown in
Figure 3 and Figure 4.

 Insert the lens approximately

seven (7) inches, and then view
the side of the belt that contacts Figure 4
the pulley.

5/35 NTB18-077C
b. Slowly and carefully turn the front left
tire one full turn in the forward
rotation to view all of the belt.
 Holding the borescope with one
hand allows for turning the tire
with the other hand
(see Figure 5).
CAUTION: If the tire is rotated in the
rearward rotation, the camera lens
may get caught between the belt and
pulley.
Figure 5

c. Was damage found?

 YES: Skip to step 6f.
 NO: Proceed to step 6d.
Pulley

d. Inspect the other side of the belt. Front

 Insert the camera lens in the

second location where shown
in Figure 3 and Figure 6, and then
perform step 6b again.

e. Was damage found?

 YES: Continue to step 6f. Figure 6
 NO: Proceed to step 10 on
page 13 and replace valve
body.

NOTE: For additional information, see video # 544: “CVT Belt Inspection”. This video
is located under the TECH TRAINING GARAGE VIDEOS tab in Virtual Academy.

6/35 NTB18-077C
 f. If CVT replacement is required based
on the inspection results from 6b and
6d, use borescope J-51951 to record VIN
a continuous video, 15 seconds or label
less, of the most severe evidence of
belt slip and the VIN on the
F.M.V.S.S. certification label (VIN
label). See Figure 7.

Figure 7
NOTE: This required video must be attached to the Powertrain Call Center CVT
Preauthorization Form (in ASIST) prior to calling for authorization. Failure to submit
a continuous video will cause immediate denial of request for replacement.
 Before starting to record, make sure the camera handle’s AA batteries are
charged and the LCD monitor’s battery is charged.
 The video will show a backward or reversed image when the mirror end is used;
this is okay.
 The required video must show clear evidence of belt slippage and be 15 seconds
or less.

Inspect these sides

Do not inspect
these sides

Figure 8

7. Reassemble the CVT.

NOTE: The CVT unit requiring replacement will need to be reassembled for Nissan
parts return/collection.

7/35 NTB18-077C
8. Obtain authorization to replace the CVT assembly. See CVT Assembly Replacement
Approval Procedures on page 35.

9. After receiving authorization, replace the CVT assembly, then proceed to page 20 to
reprogram the TCM, and then perform Additional Service when Replacing Transaxle
Assembly. Additional information related to TCM reprogramming is found on page 19.

 For CVT assembly replacement, refer to the ESM, section TRANSMISSION &
DRIVELINE > TRANSAXLE & TRANSMISSION > CVT: RE0F10D > UNIT
REMOVAL AND INSTALLATION > TRANSAXLE ASSEMBLY.
 IMPORTANT: For those vehicles that have an external CVT cooler, a cooler
flush is required after a valve body or CVT assembly replacement.

o For the procedure to flush the CVT cooler, refer to the ESM, section
TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION > CVT:
RE0F10D > BASIC INSPECTION > CVT FLUID COOLER SYSTEM.

 For the procedure to fill CVT with NS-3 CVT fluid or equivalent, refer to the ESM,
section TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION > CVT:
RE0F10D > BASIC INSPECTION > CVT FLUID.

8/35 NTB18-077C
A.

Figure 9: New belt

Figure 10: Close-up of section to be inspected

9/35 NTB18-077C
Pictures in Figure 11 and Figure 12 were taken with borescope J-51951.

OK

Visual
lines

Figure 11: Belt is OK

OK

Visual
lines

Figure 12: Belt is OK

10/35 NTB18-077C
 NG

Scuffing

Figure 13: Example of NG belt

NG

Lines
“smeared”

Figure 14: Example of NG belt

11/35 NTB18-077C
A. Pictures in Figure 15-Figure 17 were taken with borescope J-51951.

NG

Figure 15: Example of NG belt

NG

Figure 16: Example of NG belt

NG

Figure 17: Example of NG belt

12/35 NTB18-077C
New Control Valve (Valve Body), Strainer and Pan Installation

IMPORTANT:
 For those vehicles that have an external CVT cooler, a cooler flush is required after
a valve body or CVT assembly replacement.
 For the procedure to flush the CVT cooler, refer to the ESM, section
TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION > CVT:
RE0F10D > BASIC INSPECTION > CVT FLUID COOLER SYSTEM.
 Installation steps in this bulletin may contain different style parts than what were
originally installed in the CVT. Pay careful attention, REASSEMBLY MAY NOT BE
IDENTICAL TO DISASSEMBLY.
 Confirm that the QR label, control valve and CD part numbers all match before
installing the control valve.
 For additional information, see video # 547: “CVT Belt and Pulley Replacement” and
fast forward to minute marker 20:09. This video is located under the TECH
TRAINING GARAGE VIDEOS tab in Virtual Academy.

CAUTION: Handle the valve body carefully.

NOTE: If an oil strainer bracket was

removed, discard it. An oil strainer bracket
(Figure 18) will not be used with the new oil
strainer.
Oil strainer
bracket

Figure 18

10. Install a new lip seal (Figure 19).

 Do NOT reuse the old lip seal.

 Apply a small amount of petroleum

jelly or equivalent to the lip seal to
keep it in place on the CVT.
Lip seal

Figure 19

13/35 NTB18-077C
 25 mm bolts
11. Install a new valve body with eleven (11)
mounting bolts (Figure 20).
 See the PARTS INFORMATION on
page 32 for the new Valve Body.

IMPORTANT: Leave four (4) bolt 44 mm bolts

holes empty during this step.
CAUTION: Make sure the wiring
harness does not get pinched (see
Figure 21 and Figure 22 for correct
routing).
Figure 20
 54 mm (2.125 inches) long bolt ;
7 pieces

 44 mm (1.73 inch) long bolt ;

2 pieces

 25 mm l (1 inch) long bolt ;

2 pieces
CAUTION: The two 25 mm bolts are installed WITHOUT the strainer bracket.

 Bolt torque: 7.9 N•m (0.81 kg-m, 70 in-lb.)

Correctly routed Incorrectly routed

Figure 21 Figure 22

14/35 NTB18-077C
12. Replace the metal bracket of the fluid temperature sensor as follows:

NOTE: The new bracket will be oriented the same way the old bracket was.

a. Cut the old plastic zip tie with an appropriate tool to remove the fluid temperature
sensor’s metal bracket from the terminal harness assembly (Figure 23 and
Figure 24).

CAUTION: Cut the plastic zip tie over the metal bracket to avoid damage to the
fluid temperature sensor.

b. Discard the removed metal bracket and plastic zip tie.

c. Use the new plastic zip tie from the PARTS INFORMATION on page 32 to attach
the fluid temperature sensor of the terminal connector harness to the fluid
temperature sensor’s new metal bracket.

IMPORTANT:
 Locate the plastic zip tie at the center notch of three notches on the fluid
temperature sensor (Figure 24).

 Tighten the plastic zip tie so that it is oriented as shown in Figure 23.

d. Cut off the plastic zip tie excess.

Fluid temperature
sensor
Fluid temperature
sensor

Plastic zip tie

located at corner Plastic zip tie
Fluid temperature in center notch
sensor’s metal
Figure 23 bracket Figure 24

15/35 NTB18-077C
13. Connect the electrical harness connector
(Figure 25).

Harness
connector

Figure 25

Empty bolt hole

14. Install the CVT fluid temperature sensor
bracket to the valve body with one (1)
bolt (Figure 26).
NOTE: Leave one (1) bolt hole empty as
it will be used to secure the oil strainer
at a later step.
 54 mm (2.125 inches) long bolt. 1 bolt
 Bolt torque: 7.9 N•m (0.81 kg-m,
70 in-lb.)

Figure 26

15. Install the new oil strainer with its new

O-ring seal with two (2) bolts (Figure
27).
NOTE: The replacement strainer may be
a different shape than the original.

 54 mm (2.125 inches) long bolt ; 54 mm

2 pieces. bolts
 Bolt torque: 7.9 N•m (0.81 kg-m,
70 in-lb.)

Figure 27

16/35 NTB18-077C
16. Install the manual plate, lock washer,
Manual plate Slot and manual
and nut (Figure 28).
plate end
NOTE: Make sure the manual plate fits
into the slot of the manual valve before
Lock washer
applying torque to the nut.
 Reuse the existing manual plate, lock
washer, and nut. Nut
 Nut torque: 22.1 N•m (2.3 kg-m,
16 ft-lb.)
Manual valve
17. Clean the original oil pan and magnets
with a suitable cleaner. Visible debris
Figure 28
should not be present at reassembly.
18. Reassemble the original magnets to the
oil pan.
NOTE: Return the magnets to their
original locations.
19. Install a new oil pan gasket to the oil pan.
20. Install the oil pan bolts (see Figure 29).
 Reuse the existing oil pan bolts.
 Oil pan bolts torque: 7.9 N•m
(0.81 kg-m, 70 in-lb.)
21. Install a new drain plug washer to the
drain plug on the oil pan.
Figure 29
 Drain plug torque: 34.3 N•m
(3.5 kg-m, 25 ft-lb.)

22. Fill the CVT assembly with NS-3 CVT fluid or equivalent.
 For the procedure to fill CVT with NS-3 CVT fluid or equivalent, refer to the ESM,
section TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION > CVT:
RE0F10D > BASIC INSPECTION > CVT FLUID.

IMPORTANT: For those vehicles that have an external CVT cooler, a cooler flush is
required after a valve body or CVT assembly replacement.

 For the procedure to flush the CVT cooler, refer to the ESM, section
TRANSMISSION & DRIVELINE > TRANSAXLE & TRANSMISSION > CVT:
RE0F10D > BASIC INSPECTION > CVT FLUID COOLER SYSTEM.

17/35 NTB18-077C
 23. Attach the QR label (Figure 30) with the new calibration data onto the transmission
range switch (inhibitor switch Figure 31).
 A QR Label and CD-R are included with the new valve body.
 Confirm that the QR label and the CD-R part numbers are the same (Figure 31).

Inhibitor
CD-R
switch

QR Label

QR Label

Figure 30 Figure 31

24. Proceed to the next page for TCM Reprogram and Additional Service.

18/35 NTB18-077C
TCM Reprogram and Additional Service

The steps starting on the next page must be completed in the following order:

A. TCM Reprogram, if needed.

B. Perform Additional Service

For Transaxle Assembly Replacement

 Perform ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE
ASSEMBLY.

 Refer to the ESM, section TRANSMISSION & DRIVELINE - TRANSAXLE &

TRANSMISSION - CVT: RE0F10D - BASIC INSPECTION - ADDITIONAL
SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY.

For Valve Body Replacement:

 Perform ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE.

 Refer to the ESM, section TRANSMISSION & DRIVELINE > TRANSAXLE &
TRANSMISSION > CVT: RE0F10D > BASIC INSPECTION > ADDITIONAL
SERVICE WHEN REPLACING CONTROL VALVE.

C. Confirm DTCs are erased.

D. Confirm that there are no fluid leaks.

19/35 NTB18-077C
A.
TCM Reprogramming

IMPORTANT: Repairs performed for this bulletin require CONSULT-III plus (C-III plus)
Diagnostic result reporting function-Setting to be turned ON and Diagnosis (All Systems) to
be selected. If not done, it may result in a repair being non-warrantable.

IMPORTANT: Before starting, make sure:

 ASIST on the CONSULT PC has been synchronized (updated) to the current date.
 All C-III plus software updates (if any) have been installed.
 The CONSULT PC is connected to the Internet (Wi-Fi or cable).

NOTE:

 Most instructions for reprogramming with C-III plus are displayed on the CONSULT
PC screen.
 If you are not familiar with the reprogramming procedure, click here. This will link
you to the "CONSULT- III plus (C-III plus) Reprogramming" general procedure.

CAUTION:
 Connect a battery maintainer or smart charger set to reflash mode or a similar
setting. If the vehicle battery voltage drops below 12.0V or rises above 15.5V
during reprogramming, the TCM may be damaged.

 Be sure to turn OFF all vehicle electrical loads.

If a vehicle electrical load remains ON, the TCM may be damaged.

 Be sure to connect the AC Adapter.

If the CONSULT PC battery voltage drops during reprogramming, the process
will be interrupted and the TCM may be damaged.

 Turn OFF all external Bluetooth® devices (e.g., cell phones, printers, etc.)
within range of the CONSULT PC and the VI. If Bluetooth® signal waves are
within range of the CONSULT PC during reprogramming, reprogramming may
be interrupted and the TCM may be damaged.

20/35 NTB18-077C
 25. Connect the CONSULT PC to the vehicle to begin the reprogramming procedure.

26. Start C-III plus.

27. Wait for the plus VI to be recognized.

 The serial number will display when the plus VI is recognized.

28. Select Re/programming, Configuration.

Plus VI is
recognized

Figure 32

29. Follow the on-screen instructions and navigate C-III plus to the screen shown in
Figure 33 on the next page.

30. When you get to the screen shown in Figure 33, confirm reprogramming applies as
follows:
A. Find the TCM Part Number and write it on the repair order.
NOTE: This is the current TCM Part Number (P/N).

21/35 NTB18-077C
 Current TCM P/N
TRANSMISSION

31036 -

Figure 33

B.

B. Compare the P/N you wrote down to the numbers in the CURRENT TCM PART
NUMBER BEFORE REPROGRAMMING column in Table A below.

 If there is a match, continue with the reprogramming procedure.

 If there is not a match, reprogramming is not needed. Continue to step 40 on

page 27 and perform ADDITIONAL SERVICE.

Table A
CURRENT TCM PART NUMBER BEFORE
MODEL MODEL YEAR
REPROGRAMMING: 31036 -
2017 3YU2A, 3YU2B, 3YU9A
Sentra
2018 5UD2A, 5UD9A

22/35 NTB18-077C
31. Follow the on-screen instructions to navigate C-III plus and reprogram the TCM.
NOTE:
 In some cases, more than one new P/N for reprogramming is available.
 If more than one new P/N is available, the screen in Figure 34 displays.
 Select and use the reprogramming option that does not have the message
“Caution! Use ONLY with NTBXX-XXX”.
 If you get this screen and it is blank (no reprogramming listed), it means there is no
reprogramming available for this vehicle.

TRANSMISSION

Figure 34
 Before reprogramming will start, you will be required to enter your User Name and
Password.
 The CONSULT PC must be connected to the Internet (Wi-Fi or cable).
 If you do not know your User Name and Password, contact your service
manager.

Figure 35

23/35 NTB18-077C
32. When the screen in Figure 36 displays, reprogramming is complete.

NOTE: If the screen in Figure 36 does not display (indicating that reprogramming did
not complete), refer to the information on the next page.

33. Disconnect the battery maintainer/smart charger from the vehicle.

34. Select Next.

Figure 36

NOTE:
 In the next step (page 26) you will perform Erase All DTCs.
 DTC erase is required before C-III plus will provide the final reprogramming
confirmation report.

24/35 NTB18-077C
TCM Recovery:

Do not disconnect plus VI or shut down C-III plus if reprogramming does not
complete.

If reprogramming does not complete and the “!?” icon displays as shown in
Figure 37:

 Check battery voltage

(12.0–15.5 V).

 Ignition is ON, engine OFF.

 External Bluetooth® devices

are OFF.

 All electrical loads are OFF.

 Select retry and follow the

on screen instructions.

 “Retry” may not go through

on first attempt and can be
selected more than once. Figure 37

If reprogramming does not complete and the “X” icon displays as shown in
Figure 38:

 Check battery voltage

(12.0 – 15.5 V).

 CONSULT A/C adapter is

plugged in.

 Ignition is ON, engine OFF.

 Transmission is in Park.

 All C-III plus / VI cables are

securely connected.

 All C-III plus updates are

installed.
Figure 38
 Select Home, and restart
the reprogram procedure
from the beginning.

25/35 NTB18-077C
35. Follow the on-screen instructions to Erase All DTCs.

36. When the entire reprogramming process is complete, the screen in Figure 39 will
display.

37. Verify the before and after part numbers are different.

38. Print a copy of this screen (Figure 39) and attach it to the repair order for warranty
documentation.

39. Select Confirm.

31036 - _ _ _ _ _

31036 - _ _ _ _ _

TRANSMISSION

Figure 39

26/35 NTB18-077C
40. Perform ADDITIONAL SERVICE.
 Refer to the ESM, section TRANSMISSION & DRIVELINE > TRANSAXLE &
TRANSMISSION > CVT: RE0F10D - BASIC INSPECTION >
 ADDITIONAL SERVICE WHEN REPLACING CONTROL VALVE
OR
 ADDITIONAL SERVICE WHEN REPLACING TRANSAXLE ASSEMBLY

 Use the check-off table below and check off each Additional Service Procedure as
they are performed.

IMPORTANT: Check off these additional services as they are completed and attach
this to the repair order when finished.

CHECK OFF ADDITIONAL SERVICE PROCEDURE

VALVE CVT
BODY ASSEMBLY
PRINT CURRENT CALIBRATION DATA

CHECK THE SERIAL NUMBER

WRITE THE DATA (WRITE IP CHARA)

PRINT NEW CALIBRATION DATA

FWD CLUTCH POINT LEARNING (1)
Not required
(Reference provided on page 28.)
PERFORM SELECT LEARNING
(DRIVE/REVERSE LEARNING. Reference provided on page 31.)
ERASE CVT FLUID DEGRADATION LEVEL DATA
(1) If needed, TCM reprogramming must be done first.

41. Return C-III plus to the Home screen.

42. Turn OFF C-III plus and the vehicle ignition.

43. Disconnect C-III plus from the vehicle.

44. Test drive the vehicle:

 Make sure the MIL is OFF.
 This bulletin does not cover any DTC repairs other than those listed under “If You
Confirm” on page 1.
 If the MIL comes ON, go to ASIST for further diagnostic information.
 Verify the CVT operates normally and no abnormal noises are heard during a test
drive.

27/35 NTB18-077C
FWD CLUTCH POINT LEARNING (using CONSULT-III plus)
NOTE: If a TCM update is available (see page 21), the TCM MUST be reprogrammed
before performing FWD CLUTCH POINT LEARNING.

45. Apply the vehicle’s parking brake.

46. Start the engine and warm up the CVT
to an operating temperature (50-100o C
[122-212o F]).
47. Connect the CONSULT PC to the
vehicle.
48. Start C-III plus.
49. Wait for the plus VI to be recognized.
 The serial number will display when
the plus VI is recognized.
50. Select Diagnosis (One System). Figure 40

51. Select Work Support under

TRANSMISSION.

IMPORTANT: The following FWD CLUTCH Figure 41

POINT LEARNING will be performed twice;
once in Drive (D) and once in Reverse (R).

52. Select FWD CLUTCH POINT

LEARNING and then Start.

Figure 42

28/35 NTB18-077C
53. With the engine still running and at idle,
depress the brake pedal and shift the
CVT into neutral (N).
 Confirm that all of the required
conditions indicated in Figure 43 are
being met.
Required
conditions
54. Select Start.

Figure 43

55. While maintaining all conditions shown

in Figure 43 and the “Current status”
indicates “EXECUTING” as shown in
Figure 44, shift the CVT into D and then
wait until the Current status indicates
“COMPLETED” as shown in Figure 45.
NOTE: This may take up to three (3)
minutes to complete.

Figure 44

56. When the screen in Figure 45 is

displayed, shift the CVT into Park (P),
and then select End.

57. Turn the engine OFF and then back ON. Figure 45

29/35 NTB18-077C
58. Select FWD CLUTCH POINT
LEARNING and then Start.

Figure 46

59. With the engine still running and at idle,

depress the brake pedal and shift
the CVT into Neutral (N).
 Confirm that all of the conditions
indicated in Figure 47 are being met.

Required
60. Select Start. conditions

Figure 47

61. While maintaining all conditions shown

in Figure 47 and the Current status
indicates EXECUTING, shift the CVT
into R and then wait until the Current
status indicates COMPLETED.
NOTE: This may take up to 3 minutes to
complete.

Figure 48

30/35 NTB18-077C
62. When the screen in Figure 49 is
displayed, select End.

Figure 49

SELECT LEARNING (DRIVE/REVERSE LEARNING)

Perform Select Learning (Drive / Reverse Learning) as follows:

63. Set the parking brake.

64. Start the engine, and then wait five (5) seconds.

65. Move the shift selector to the N position and hold more than two (2) seconds, and then
move it to the D position and wait for transmission engagement.

66. Repeat step 65 ten (10) times.

67. Move the shift selector to the N position and hold for more than 2 seconds, and then
move it to the R position and wait for transmission engagement.

68. Repeat step 67 ten (10) times.

69. Move the shift selector to the P position, and then turn the ignition OFF.

31/35 NTB18-077C
PARTS INFORMATION
DESCRIPTION PART NUMBER QUANTITY
CVT ASSEMBLY (1) (2) 1
VALVE ASSEMBLY KIT-CONTROL
3170E-28X0B 1
(valve body)
Valve Assembly Kit-Control includes: - -
VALVE ASSEMBLY-CONTROL (3) - 1
STRAINER ASSY-OIL AUTO TRANS - 1
GASKET-OIL PAN - 1
BRACKET (for temperature sensor) - 1
BAND (zip tie for sensor bracket) - 1
SEAL-LIP - 1
SEAL, O-RING (fluid filler plug gasket) - 1
WASHER-DRAIN 11026-JA00A 1
NS-3 CVT Fluid (4) (5) 999MP-CV0NS3 As needed
Lens Swab (6) J-51963 (Shop supply) As needed
(1) If the CVT assembly is being replaced, no other parts in the table above, except NS-3
CVT fluid or equivalent, are needed.
(2) Refer to the Electronic Parts Catalog (EPC) or equivalent for the correct part number.
(3) Includes QR Label and CD-R.
(4) For warranty repairs, Nissan NS-3 CVT Fluid must be used. For customer pay repairs,
Nissan NS-3 CVT Fluid is recommended, but an equivalent fluid may be used.
(5) NS-3 CVT Fluid can be ordered through the Nissan Maintenance Advantage program:
Phone: 877-NIS-NMA1 (877-647-6621) or Website: Order via link on dealer portal
www.NNAnet.com and click on the “Maintenance Advantage” link.
(6) Lens swabs are available from Tech•Mate online: www.nissantechmate.com, or by
phone: 1-800-662-2001.

Tech Cam J-51951

Lens swab J-51963

(not part of J-51951)
Figure 50

Additional kits and components of Tech Cam J-51951 are available from Tech•Mate online:
www.nissantechmate.com, or by phone: 1-800-662-2001.

32/35 NTB18-077C
CLAIMS INFORMATION

NOTE: Refer to CVT Assembly Replacement Approval Procedures (on page 35) before
submitting a claim.

If belt condition shows no signs of belt slip (OK)

Submit a Primary Part (PP) type line claim using the following claims coding:

DESCRIPTION PFP OP CODE SYM DIA FRT

RPL CVT CONTROL VALVE ASSY (1) JD48AA ZE 32 (2)
(1) Reference the Parts Information Table and use the applicable Control Valve Assembly
Part Number (31705-*****) as the Primary Failed Part.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic
procedures subsequently required. Do NOT claim any diagnostic OP Codes with this
claim.

And

DESCRIPTION OP CODE FRT

Inspect CVT Belt, Belt = OK JX37AA 0.3

And if TCM requires reprogramming

OPERATION PFP OP CODE SYM DIAG FRT

TCM Reprogramming (3) JE99AA ZE 32 (4)
(3) Refer to the Electronic Parts Catalog (EPC) or equivalent and use the TCM part number
(31036 - *****) as the PFP.
(4) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic
procedures subsequently required. Do NOT claim any diagnostic OP Codes with this
claim.

Claims Information continued on the next page.

33/35 NTB18-077C
CLAIMS INFORMATION (continued)

If belt inspection shows signs of belt slip (NG)

DESCRIPTION PFP OP CODE SYM DIA FRT

CVT R&R JD01AA (2)
(1) ZE 32
CVT TROUBLE DIAGNOSIS JX22AA 0.5

(1) Reference the Electronic Parts Catalog (EPC) or equivalent and use the CVT assembly
part number for the vehicle being repaired as the Primary Failed Part.
(2) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic
procedures subsequently required. Do NOT claim any diagnostic OP Codes with this
claim.

And

DESCRIPTION OP CODE FRT

Inspect CVT Belt, Belt = NG (Includes control valve R&I) JX36AA 1.1

And if TCM requires reprogramming

OPERATION PFP OP CODE SYM DIAG FRT

TCM Reprogramming (3) JE99AA ZE 32 (4)
(3) Refer to the Electronic Parts Catalog (EPC) or equivalent and use the TCM part number
(31036 - *****) as the PFP.
(4) Reference the current Nissan Warranty Flat Rate Manual and use the indicated Flat
Rate Time.
NOTE: FRT allows adequate time to access DTC codes. No other diagnostic
procedures subsequently required. Do NOT claim any diagnostic OP Codes with this
claim.

34/35 NTB18-077C
CVT Assembly Replacement Approval Procedures

 If CVT belt inspection indicates CVT assembly replacement is required:

a. Complete the PCC CVT Preauthorization Form in ASIST.

b. Attach the required video (15 seconds or less) to the CVT Preauthorization
Form.
 Failure to submit a continuous video showing evidence of belt slip and the
VIN will cause immediate denial of request for CVT unit replacement.

c. Call the PCC for authorization at 800-973-9992 (opt 2).

IMPORTANT: Make sure the video has a clear image of the VIN on the F.M.V.S.S.
certification label (VIN label).

AMENDMENT HISTORY

PUBLISHED DATE REFERENCE DESCRIPTION

November 8, 2018 NTB18-077 Original bulletin published
Page 20 revised, and NV200 and Taxi vehicles
August 1, 2019 NTB18-077A
removed from bulletin
October 1, 2019 NTB18-077B Table A revised
June 22, 2021 NTB18-077C Removed Rogue Sport

35/35 NTB18-077C