No.

: C-SBP205H36A-01-GGS-0

APPROVAL SHEET
SPECIFICATIONS OF HERMETIC SCROLL COMPRESSOR

MODEL C-SBP205H36A

△
△
△
△
△
NO. DATE PAGE REVISION DETAILS PAPCDL SIGNED CLIENT SIGNED

REVISION RECORD

USER: MANUFACTURER:
Panasonic Appliances Compressor (Dalian) Co., Ltd.

PURCHASING TECHNICAL
LEADER APPROVED CHECKED SUBMITTED
MANAGER MANAGER

1
 Model: C-SBP205H36A
File No: C-SBP205H36A-01-GGS-0
Section 1. General Specifications
Content Unit Specification
Compressor Model — C-SBP205H36A
Type — Hermetic Scroll Compressor
Application — High Back Pressure
Evap. Temp. Range °C (°F) -15~12 (5~54)
Compressor Cooling Type — Natural Cooling
Phase — 3
Power Source Rated Voltage V 208-230
Rated Frequency Hz 60
Voltage Range V 187-253
Weight (Including Oil) kg (lb) 40(88.2)
Refrigerant — R410A
Oil Type — FV68S or Equivalent
Oil Charge ml (fl oz) 1700 (57.5)
3 3
Displacement cm (in ) /rev 66.8(4.08)
Motor Type — 3-PH Induction Motor
Number of Poles — 2
Electrical Insulation Class E
Nominal Revolution min-1 3450
Motor
Locked Rotor Ampere A 153
U-V 0.484
Winding Resistance
Ω U-W 0.484
[at 25°C (77°F）]
V-W 0.458
Suction Line (O.D.) mm (in) 22.2 (0.875)
Connection Tube
Discharge Line (O.D.) mm (in) 12.7 (0.500)
Compressor Surface Paint — Black Paint
Notes
1 Voltage range is applied at standard rating conditions.
2 Motor specifications in the table are the average values for your reference.
3 ( ): All units with parentheses are reference values.

Expiration of Specification
Expiration of this specification shall be effected until issuing a notice with indication of the expiration date from the
issued date . In case of improvement or elimination of this specification , it shall be handled by the revision record
based on agreement between both sides.

2
 Model: C-SBP205H36A
File No: C-SBP205H36A-01-GGS-0

Section 2. Performance Warranty

2.1 Performance
Hz 60 60 Remark
Power Source (3PH)
V 208 230
W 20,300 20,400 ±5%
Capacity
(BTU/hr) 69,264 69,605 reference
Input Power W 6,650 6,700 ±5%
Current A 20.80 20.50 ±5%
Standard Rating Conditions
Condensing Temp. °C (°F) 54.4(130)
Evaporating Temp. °C (°F) 7.2( 45 )
Suction Gas Temp. °C (°F) 18.3( 65 )
Liquid Temp. °C (°F) 46.1(115)
Ambient Temp. °C (°F) 35( 95 )

MP 427.7
2.2 Sound Level
Hz 60
Power Source (3PH)
V 208~230
Sound Level dB(A) 65Max.

Notes
1 The operating conditions are the same as 2.1.
2 MIC location is the distance of 1m (3.28feet) from the compressor.
3 Sound Level is an average sound pressure level in four directions.

2.3 Minimum Starting Voltage

Power Source (3PH) Hz 60
Minimum Starting Voltage V 166

Conditions
Compressor Temp. °C (°F) 10~60(50~140)
Ambient Temp. °C (°F) 10~40(50~105)
High Pressure MPa(G)/psig 3.25(471)
Low Pressure MPa(G)/psig 0.9(130.5)

2.4 Others
Content Unit Specification
L.P. S. MPa(G)/psig 2.21(320)
Design Pressure
H. P. S. MPa(G)/psig 4.15(602)
Insulation Resistance MΩ 100 (without refrigerant)
Dielectric Strength V 1800 (1 second)
Residual Moisture mg 300
Note:
1. The insulation resistance be measured with a DC500V megohm tester.

3
 Model: C-SBP205H36A
File No: C-SBP205H36A-01-GGS-0
Section 3. Standard Accessories
3.1 Accessories List

Parts Name Qty Parts code Revision No. Note

Terminal Box Cover 1 A-0101-DSB 0 Installed on Compressor

Terminal Box Clip 1 A-0201-DSB 0 Installed on Compressor

Eyelet Rub Lead Wire 1 A-0301-DSB 0 Installed on Compressor

Mounting Grommet 4 M-0101-DSB 0 Included with Compressor

Mounting Sleeve 4 M-0201-DSB 0 Included with Compressor

Screw Special 1 B-0101-DSB 0 Installed on Compressor

3.2 The Drawing for Reference

Parts Name Parts Code Revision No.

Compressor Outline Drawing D-0101-DSB 0

Mounting Parts Listing M-5101-DSB 0

Packing Dimensions D-0202-DSB 0

Wiring Diagram E-0914-DSB 0

3. 3 Inernal Motor Protector (in compressor)

Parts Name Specification

Trip Temprature 160±5℃

Inernal Motor Protector Reset Temprature 70±10℃

Trip Current 114A / 3~10s

4
 Model: C-SBP205H36A
File No: C-SBP205H36A-01-GGS-0

Section 4. Compressor Protection

4.1 Protection Required but not Included with compressor

Protection Device Items Specifications

Features To protect the compressor from reverse rotation

Reversal Defensible Relay
Rated Voltage AC208~230V

Crankcase Heater Rated Power 35 Watts

Mounting Position Located within 100mm(4 in )from the compressor shell

Discharge Thermostat Trip Temperature 130±5℃(266 ±10 °F)

Reset Temperature 95±11℃ (205 ± 20 °F)

High Pressure Switch Setting Cut-out seting no higher than 4.15Mpa(G)

Low Pressure Switch Setting Cut-out seting no lower than 0.15Mpa(G)

4.2 Position of the Protection and Refrigerant Charging

FOR LIQUID
REFRIGERANT
CHARGING

CAPILLARY

LIQUID LINE
SERVICE
OUTDOOR VALVE
INDOOR
HEAT HEAT
EXCHANGER EXCHANGER

GAS LINE
REVERSING SERVICE VALVE
VALVET

DISCHARGE FOR GAS

THERMOSTAT REFRIGERANT
CHARGING
HIGH
PRESSURE ACCUMULATOR
SWITCH

LOW
PRESSURE
SWITCH

COMPRESSOR CRANKCASE
HEATER

5
 Section 5. Operating Envelope

Suction Gas Superhea : 11.1K.

Refrigerant : R410A.

70

Transient Operation
60
Condensing Temperature（℃）

50

Normal Operation

40

30

20

10
-30 -25 -20 -15 -10 -5 0 5 10 15 20
Evaporating Temperature（℃）

6
 Section 6. Application Standard & Limit

The following requirements apply to vertical type hermetic scroll compressors:

Standard: Applicable to ordinary conditions in Japan JIS B8616 or standards relative to JIS B8616, such as standard rating
conditions, maximum operating conditions, low temperature conditions, etc.
Limit: Applicable to transitional brief period of time, such as start-up and beginning of defrost mode.
No. Item Standard Limit Note
1 Refrigerant R410A
-15~12℃(5～54 °F) -25~15℃(-13～59 °F)
2 Evaporating Temp.
0.38~1.06MPa(G)(55～154psig) 0.23~1.16MPa(G)(33～168psig)
30~60℃(86～140 °F) 65℃(149 °F)
3 Condensing Temp.
1.80~3.75MPa(G)(261～544psig) 4.18MPa(G)(606psig)
4 Compression Ratio 2~6 8

5 Winding Temp. 115℃(240 °F) Max. 125℃(257 °F)

90℃(194 °F) Max.
6 Shell Bottom Temp. Evaporating Temp.+12℃(21 °F) Min.
Ambient Temp.+11℃(20 °F) Min.

C-SB:130℃( 266°F) Max.

Discharge Gas
7 115℃(240 °F) Max.
Temp.
C-SC:135℃( 275°F) Max.

It should meet the

requirement of item 5, 6,
8 Suction Gas Temp. Superheat: 5K(10 °F)Min. No excessive noise
7 and 14 within 30cm of
the suction fitting.

Voltage at compressor
9 Running Voltage Within ±10% of the rated voltage
terminals.
Three Phase Models: 85% of the rated voltage min. Voltage at compressor
10 Starting Voltage
Single Phase Models: 90% of the rated voltage min. terminals.

On Period: Until the oil level returns to the center of the lower bearing For at least 7 minutes -
11 On/Off Cycling on/3 minutes-off is
Off Period: Until balance of high and low pressure is obtained recommendable.

Specific gravity of the

12 Refrigerant Charge oil/refrigerant(wt.)≥0.35
Oil:0.94
13 Life Time 200,000 cycle

C-SB: Center of the lower bearing C-SB:Bottom of the lower bearing

14 Minimum Oil Level

C-SC:No less than 70% of the initial oil charge

Abnormal Pressure Pressure Rise: 4.15MPa(G) (602psig) Max. By high pressure switch
15
Rise/Drop Pressure Drop: 0.15MPa(G) (22psig) Min. By low pressure switch
System Moisture
16 200ppm Max.
Level
System 1 Vol.% Max. 24 hrs. after vacuuming:
17 Uncondensable Gas
Residual Oxygen 0.1 Vol.% Max. 1.01kPa Max.
Level
18 Tilt 5。Deg.Max.

Operation beyond the above limits must be approved by Panasonic Appliances Compressor (Dalian) Co., Ltd.

(G): Gauge Pressure

7
Notes

1 Installation should be completed within 15 minutes after removing the rubber plugs.

2 Do not use the compressor to compress air.

3 Do not energize the compressor under vacuumed conditon.

4 Evacuation and Refrigerant charge ： Evacuate internal section in the refrigeration system from high and low pressure
sides and charge liquid refrigerant from condenser outlet side. Additional charge shall be done with gas condition from
low side.

5 Do not tilt over the compressor while carrying it.

6 Do not remove the paint.

7 Crankcase heater is required when the oil sump temperature is too low to meet the requirement of item 6 on page7.

8 Voltage fluctuation between compressor terminals, during operation, shall be within 2% of the rated voltage.

9 Do not operate compressor in reverse rotational direction.

10 Suction strainers are recommended for all applications.

11 Copper Piping Stress Start/Shutdown 34.32 N/mm2 Max.

Run 12.26 N/mm2 Max.

8
 Section 7. Selection of Electrical Wire
Voltage drop may occur due to the large current draw during compressor starting.
We recommend selecting the wire size from the table below.

7.1 Type of Unit

7.1.1 Window & Commercial Type Unit ① outdoor
power source

③
terminal plate compressor
indoor

7.1.2 Split Type(Separate Type)

outdoor

power ① ② ③
terminal
source indoor plate
compressor

7.2 Size Table of Electrical Wire

Size of electrical wire（mm2）

Starting current Remark③（heat-

(A) Remark ① or Remark ①+②（heat-resistance Temperature: 60°C(140°F) min.） resistance Temperature:
120°C(248°F) min.）

5m max. 10m max. 15m max. 20m max. 30m max. 50m max. 1m max.
20max. 2.0 2.0 2.0 3.5 5.5 8.0 2.0
30max. ↑ ↑ 3.5 5.5 ↑ 14.0 ↑
40max. ↑ 3.5 5.5 ↑ 8.0 ↑ ↑
50max. ↑ ↑ ↑ 8.0 14.0 22.0 ↑
60max. ↑ 5.5 ↑ ↑ ↑ ↑ ↑
70max. 3.5 ↑ 8.0 14.0 ↑ ↑ 3.5
80max. ↑ ↑ ↑ ↑ 22.0 30.0 ↑
90max. ↑ ↑ 14.0 ↑ ↑ ↑ ↑
100max. ↑ 8.0 ↑ ↑ ↑ 38.0 ↑
110max. ↑ ↑ ↑ ↑ ↑ ↑ ↑
120max. 5.5 ↑ ↑ 22.0 30.0 ↑ ↑
140max. ↑ 14.0 ↑ ↑ ↑ 50.0 5.5
160max. ↑ ↑ 22.0 ↑ ↑ ↑ ↑
180max. ↑ ↑ ↑ ↑ 38.0 60.0 8.0
200max. 8.0 ↑ ↑ 30.0 ↑ ↑ ↑
220max. ↑ ↑ ↑ ↑ 50.0 80.0 ↑
240max. ↑ ↑ ↑ ↑ ↑ ↑ 14.0
7.3 Caution of Ground
The internal motor protector does not protect the compressor against all possible conditions.
Please be sure that the system utilizes the ground connection when installed in the field.

9
 No. Part Code Qty Name
190.5 1 C-SBP205H36A 1 Compressor
[7.505]
2 A-0101-DSB 1 Terminal Box Cover
HOLE
4-φ18 φ0.709 3 A-0201-DSB 1 Terminal Box Clip
4 A-0301-DSB 1 Eyelet Rub Lead Wire
5 1 Nameplate
6 B-0101-DSB 1 Screw Special
[9.378]

[7.505]

.5 .0
]
238.2

190.5

13
[5 140

12 740]
[4
0.
.
3

[4.889]

[5.169]
124.1

131.3
41. °
5° 31.0
0°
45.

[3.039]
77.2
1 DISCHARGE TUBE φ13.1
[3.039]
[φ0.516]
10

V(S)
V(S)

[2.685]
[2.685]
SUCTION TUBE φ22.3

68.2
W(C)
3 [φ0.878] U(R)
U(R) W(C)
[2.923]
74.2
[17.785]
451.4

[16.567]

TERMINAL
420.8

φ176.4
4 [φ6.9502]
TERMINAL
[12.249]
310.9
[10.205]
259.0

5 Part Code
D-0101-DSB
[0.985]
25.0

Name
6
Compressor Outline Drawing
 No. Part QTY Name
1 M-0101-DSB 4 Mounting Grommet
2 M-0201-DSB 4 Mounting Sleeve
3 B-0101-DSB 1 Screw Special
1 40
[1.575]

M8 BOLT
2

[1.260]
WASHER

32
WASHER SPRING
8
[0.315] 3
COMPRESSOR BASE
6 ]
R1 630 20
0.
[R [0.787]

24
[1.811]

[1.811]
[0.945]
46.0

M4[1.575]
[1.457]

46
37.0
11

2 φ8.6
[φ0.339]
φ10.6
[φ0.417]

Part Code
M-5101-DSB
Name
Mounting Parts Listing
 `
12

Part Code
D-0202-DSB
Name
Packing Dimensions
 DISCHARGE
THERMOSTAT

SWITCH V

POWER
SUPPLY INTERNAL
3PH 60Hz PROTECTOR
208~230V
R
U W
S

T
COMPRESSOR
TERMINAL MAGNETIC SWITCH

R C
13

S B

T A

REVERSAL
DEFENSIBLE RELAY

CRANKCASE HEATER

Part Code
E-0914-DSB
Name
Wiring Diagram