1.
CyberBrick Module Specifications
This is an early preview version created on 2025/03/19. Content is subject to change.
1.1. Multi-Function Controller Core-XA003
Integrated Bluetooth & WiFi, Support MicroPython Programming
Parameter Value
Type-C Input Voltage DC 5V
VBAT Input Voltage 3.7V~12.6V
Antenna Type PCB Antenna
Weight 6g
Item Function
1 WS2812LED - RGB System Status Indicator
2 Stamp Cut - Solderable pinout (for integrating non-CyberBrick parts)
3 Reset Button - Reset Main Program
4 Type-C Port - Burning Firmware& Programming
5 User Button - Custom Function
1.2. Remote Control Receiver Shield -XA004
2CH DC Motor Driver, 4CH PWM Driver, 2CH WS2812 LED output.
Parameter Value
Input Voltage DC 7.4V – 12.6V
Current Standby current 60mA, Working current
200~300mA, Maximum current 3A
Output 4CH PWM, 2CH MOTOR, 2CH LED
Weight 6g
Each of Left/Right side PWM&LED ports share a maximum current of 2A.
Total PWM&LED maximum current is 3A.
Port Function
1 WS2812 Port 1 - SH1.0 3P LED port for WS2812LED strip
2 DC Motor Port 1 - SH1.0 2P DC motor port. Output voltage equal to power
input voltage. Maximum current 1A.
3 4 Servo Ports -PWM output for servos. 5V VCC.
4 WS2812 Port 2 - SH1.0 3P LED port for WS2812LED strip
5 DC Motor Port 2 - SH1.0 2P DC motor port. Output voltage equal to power
input voltage. Maximum current 1A.
6 Power Indicator - White light means power on.
7 Power Input - XH2.54 2P DC power input.
1.3. Remote Control Transmitter Shield -XA005
6CH ADC Input, 4CH Digital input
Parameter Value
Input Voltage DC 4.5 – 12.6V
Working Current 65mA
Input Channel 6CH ADC, 4CH Digital
Weight 5.5g
Port Function
1 ADC input port – Connecting ADC modules such as joystick
2 Digital input port - Connecting binary-input modules such as momentary
button
1.4. WS2812 LED Hub-XA006
Connect up to four WS2812 RGB LED
port Function
1 Input port – 3P SH1.0, 5V
2 Output port – IDC 0.8 4P
1.5. Power Switch Module-XA007
Battery On/Off Switch
Parameter Value
Input Voltage Maximum 12.7V
Weight 4.1g
Connector XH2.54 2P
1.6. Momentary Button Module-XA008
Digital Input Module
1.7. Single-Axis Joystick Module- XA009
Single Channel ADC Input Module
Parameter Value
Input Voltage 3.3V
Output Signal Type ADC
Output Channel 1CH
Sensor Type Potentiometer
Electrical resistance 10kΩ
Weight 6.15g
Connector 3-pin SH1.0
1.8. Three-Position Rocker Switch Module-XA010
Parameter Value
Input Voltage 3.3V
Output Signal Type ADC
Position 3
Weight 2.73g
Connector 3-pin SH1.0
1.9. Dual-Axis Joystick Module - XA011
2CH ADC Output
Parameter Value
Output Signal Type ADC
Output Channel 2CH
Sensor Type Potentiometer
Electrical resistance 10kΩ
Connector 3-pin SH1.0 * 2
Weight 6.6g
1.10. WS2812 RGB LED - KB003
Parameter Value
Input Voltage 3.5~5.3V
Connector IDC 0.8mm 4P
1.11. Li-on Battery
2S 700mAh Li-on Battery with XH2.54 2P Connector
