Industrial Connectors Catalog

OMRON Provides Industrial Connector Solutio

A Wide Range of Models for Serial (Network) Communications and Parallel Connections
Connections through Connector Units for Fewer Cables and Less Wiring Work on FA Sites
1 Fewer Cables
2 Less Wiring Work and Greater Work Procedure Standardization
3 Easier Maintenance

Industrial Ethernet: EtherNet/IP™ EtherCAT®

Page 14

Not Water
XS5 Water Resistant (IP67) Resistant XS5/6

Parallel Connections Page 30

Input Device Examples Relay Cables with Connectors

Sensors with Built-in Connectors Connectors with Cables, Sockets/Plugs at the Ends

E2E E3Z D4CC XS W

Prewired Sensors
Connectors with Cables, Socket at One End + Assembly Connector Plugs

Water
Resistant E2E E3Z WL-N D4C XS F XS G

(IP67)
Prewired Sensors + Assembly Connectors
Assembly Connector Sockets + Connector Plugs with Cables

E2E XS G
XS C XS H

Sensors +
Embedded Screw Connectors XS M Y-Joint Plugs/Sockets + Connectors with Cables, Sockets/Plugs at the Ends

XS R
Panel-mounting Connectors XS M
XS W

2 I N D U S T R I A L C O N N E C T O R S C ATA L O G
ns for FA Equipment

Multivendor Network: DeviceNet™

Page 126
Peripherals for Peripherals for Standard Slaves
Environment-resistive Slaves (IP67)
Smartclick Micro
Connectors for
Thin Cables
DCN2 Parallel Connectors Parallel Connectors
with Screws with Screws
DCN1 XW4B

Smartclick Micro
Connectors for Thin Cable
Thin Cables DCN1
DCA1

7/8-16UN Mini
Connectors for Thick Cable
Thick Cables DCA2
DCA2

Parallel I/O connector

Terminal Box
Connections to Various
FA Devices

Connector Terminal Box XN2A-1470 Connectors

for FA devices
with e-CON
connectors
Cable Relay Connections Connections to Original
Not Control Boards
XW3 Water
Resistant
XN2A-1470 XN2B-1470
Panel-mounting Connectors XN2A-1 70 XN2D-1 71

Connections to FA Devices
with Terminal Blocks

XS P

Note: The connections shown above are conceptual only.

I N D U S T R I A L C O N N E C T O R S C ATA L O G 3
 Examples of the Benefits of Connector Units: Less Wiring Work and Fewer Cables
Fewer Cables

Reducing the Number of Cables by Using Connector Terminal Box,

T-Joint Plugs/Sockets, and Y-Joint Plugs/Sockets
You can use Connector Terminal Box, T-Joint Plugs/Sockets, and Y-Joint Plugs/Sockets to reduce the number of
cables connected to the control panel.

From To

Connector Terminal Box

XW3

Sensor Eight cables Control Sensor One cable Control

panel panel

Number of Cables Reduced

by Using a Common Cable

Y-Joint Plug/Socket
Connector
XS R

Sensor Four cables Control Sensor Two cables Control

panel panel

4 I N D U S T R I A L C O N N E C T O R S C ATA L O G
 Less Wiring Work and Greater Work Procedure Standardization

Wiring Work and Mistakes Reduced by Using a Connector between a Sensor and the Control Panel

From To

Connector
Sensor Relay terminal block Sensor

Control panel Control panel

1 Reduced Work
Reduced Wiring Work

From To
Wire preparation: Attaching terminals: Screw connections:
90 s 190 s 120 s

Work
reduced by
approx. 99%!
Cli
ck!

Installation Installation

6 min and 40 s 4s
XS5
* The above estimates are for connecting a 4-conductor cable to
an 8-terminal relay terminal box.
The required time depends on the worker.
The above values are reference values from an OMRON survey.

2 Work Procedure Standardization

Preventing Wiring Mistakes

From To
Correct Wrong Plug Socket
Wiring Mistake

Coding Keys Prevent Wiring Mistakes

I N D U S T R I A L C O N N E C T O R S C ATA L O G 5
 Examples of the Benefits of Connector Units: Less Wiring Work and Fewer Cables
Easier Maintenance

1 Reduced Work for Sensor Replacement

From To

Sensor Replacement Time Sensor Replacement Time

Sensor Replacement Procedure 5 min 8s Work

Removing wires: Preparing wires: Attaching terminals: Connecting wires: reduced by
100 s 45 s 95 s 60 s XS5
approx. 97%!

* The above estimates are for replacing a Prewired Sensor with a 4-conductor cable.
The required time depends on the worker.
The above values are reference values from an OMRON survey.

2 Reduced Work for Cable Replacement

From To

Replaced
Damaged Damaged cable section

Cable damage Cable damage

Entire cable must be replaced. Only one connector relay cable needs to be replaced.

Extensive work is required. Minimal work is required.

6 I N D U S T R I A L C O N N E C T O R S C ATA L O G
Industrial
Industr
trial Ethernet Connectors
Connectors for Increasingly Common Industrial Networks Based on Ethernet, such as EtherCAT®

Application Example

Ideal for in-cabinet Ideal for out-of-cabinet

XS6W-6LSZH XS6W-5PUR XS5 XS6

Standard Connectors Standard Rugged M12 Connectors Rugged Assembly

Connectors Connectors Connectors

Cables with Standard RJ45 Connectors

RJ45 Connector Shape Double Shielding (LSZH Cables)

Overall braiding and individual foil shield on each wire pair

Cables with Rugged RJ45 Connectors

RJ45 Connector Shape

Double Shielding (PVC Cables)

Strong latch

Cables with M12 Connectors

Overall braiding and individual foil shield
M12 Connector Shape

Shielded structure

I N D U S T R I A L C O N N E C T O R S C ATA L O G 7
 M12 Smartclick Connectors: XS5 and XW3D
One-step Connectors Eliminate the Problems of Screw Connectors

1 One-step Connection
Reduced Wiring Work and No Torque Management

Installation Time

Connection is completed with

a rotation of approximately 1/8. Confirm connection
with visual marks.

Clic
12 s k!

4s Insert fully.
Rotate 1/8 turn.
Screw connections Smartclick

2 Bayonet Lock Mechanism

No Loosening Due to Machine Vibration and No Need for
Periodic Screw Tightening

3 Connections with a Distinct Clicking Sensation * Enlargement of Bayonet

Lock Mechanism

Prevents Insufficient Tightening and Standardizes

Work Procedures
Clic
k! Only with Smartclick!

Even ports in the middle

Rotate 1/8 turn. can be easily connected
4 Compatible with M12 Threaded Connectors and removed with a
1/8th turn.
Applicable to Existing Equipment with
M12 Threaded Connectors
XS5 Smartclick M12 Threaded
Plug Connector Plug Connector

XS5 Smartclick
One-step connection Thread connection
Socket Connector

M12 Threaded
Socket Connector
Thread connection Thread connection XW3D M12 Connector Terminal Box

All combinations can be connected.

The Connector is screwed on to make the connection when a
Smartclick Connector is connected to a Threaded Connector.

8 I N D U S T R I A L C O N N E C T O R S C ATA L O G
 XS5C/G-D418 M12 Round Water-resistant Pressure-welded Assembly Connectors

Assembly Connectors enable easy connections with standard tools.

Convenient to adjust cable lengths, to add connectors to
Prewired Sensors, and for may other FA site applications.

No Torque Management
ag
agement
t

Visual
confirmation is
possible. Water-resistant
bushing with tabs
osition Is Clear
Tightened Position

Easy Stock Management

Wires from
Previously, a different connector was required AWG26 to Handles cable outer diameters of
for each cable diameter. With Pressure-welding 3 to 8 mm. For diameters of 5 to
AWG18 can be 8 mm, just remove the tabbed,
Connectors, only one Connector is required for pressure-welded. water-resistant bushing.
cable outer diameters of 3 to 8 mm.
* A 5-mm-dia. cable connects with or without the bushing.

No Special Tools Required Just Six Steps to Complete Wiring with No Special Tools!

1 3 5

Remove the cable sheath. Insert the wires into the wire guides in the Align the pink marker and insert the Cap Unit
pressure-welding cover. into the Connection Block.

2 4 6

Insert the wires into the Cap Unit. Cut off the ends of the wires that extend Twist the Cap Unit and Connection Block
from the Unit. to pressure-weld the wires.

XS3W M8 to M12 Conversion Cables Tool for M12 Threaded Connectors

You can use these Cables to connect Sensors with M8 Connectors to equipment Use this tool to tighten locks on
with M12 connectors. M12 Threaded Connectors to
the specified torque.

M8 to M12 Conversion Cables

M8 connector M12 connector
XS3W-M 2 - C2-A
XY2F-0004

Accessories for M12 Connectors

Accessories are available for many different applications. Loosening-
preventing
Water-re
Water-resistant
esistant Covers
Co Dust Covers Sputter Protective Cover
over C Ring

XS5Z-1
XS5Z-11
11 XS2Z-11
XS2 XS2Z-22 XS2Z-13 XS2Z-15/XS2Z-14 XS2Z-31 XS2Z-18

I N D U S T R I A L C O N N E C T O R S C ATA L O G 9
 Standards
M12: IEC 61076-2-101 Standard
Th
he sp
spec
pec
ecifififiic
icatio
icat ions
io ns and
d mat
atin
tin
ing
ng di
dime
dime
mens
n ionss of M1
ns M122 Ro
Roun
Rounund
d Co
Conn
nnectors comply with IEC 61076-2-101.
nn
OMRON prrov ovides M12 2 Rou
o nd Con onne
nect
ne cto
ctors with
h matin
atin
at ing
ng shapes that match many applilica
ca
ati
tions.

Coding Keys
A-coding B-co
codi
d ng
g

Plug Socket Plug Socket

d d d d

e c c e e c c e

f f f f

D-coding Model Example

A-coding
Plug Socket XS5F-D421-C80-F
A-coding: For DC Sensors
d d B-coding
XS2F-A421-B90-F
B-coding: For AC Sensors
e c c e

XS5H-T421-CM0-K
f f D-coding: For industrial Ethernet

M8: IEC61076-2-104 Standard

The specifications and mating dimensionss of M8 Round Connectors comply with IEC 61076-2-104.
OMRON provides M8 Round Connectors with mating shapes that match many applications.

Coding
g Keys
A-coding (3, 4 poles)
l ) B-coding (5 poles)

Plug Socket Plug Socket

3 poles
d f f d
f f

c e e c c e e c

4 poless
Model Example
A-coding

d f f d XS3F-M321-302-A
2A
A-coding:: 3 pol
oles
les
es

c e e c XS F-M421-402-A
XS
XS3
A- oding: 4 poles
A-c

B-coding
XS3
S F-M
S3 M521
5 -502-A
52 2-A
-A
A
B oding: 5 pol
B-c poles
e

10 I N D U S T R I A L C O N N E C T O R S C ATA L O G
 Note: IP- degrees of protection given in this document were confirmed by OMRON with the following specified testing methods.
IP67 Degree of Protection Confirm seal performance in the actual application environment and under actual operating conditions.

IEC (International Electrotechnical Commission)Standard (IEC 60529)

IP-
Degree of Protection Symbol (International Protection)
First Symbol: Protection against Solid Objects Oil Resistance
Code Degree of protection Degree of protection
0 No protection Oilproof No harmful effects when subjected to oil drops or oil spray from any direction.
50 dia. mm
Full penetration of 50-mm diameter of sphere not Oil- No penetration into internal parts when subjected to oil drops or
1
allowed. Contact with hazardous parts not permitted. resistant oil spray from any direction.
12.5 dia. mm Full penetration of 12.5-mm diameter of sphere Note: Oil resistance is confirmed using oils and cutting oils stipulated
2 not allowed. The jointed test linger shall have by OMRON (equivalent to previous JEM standards).
adequate clearance from hazardous parts.

3
2.5 mm
The access probe of 2.5-mm diameter shall
not penetrate.
* 1. OMRON Test Methods
The Proximity Sensor’s IP67 degree of protection was confirmed by performing
the tests described in the table below and making sure that the sensing distance
1 mm and installation resistance satisfied the performance specifications after repeating
The access probe of 1.0-mm diameter shall
4 a heat shock cycle 5 times, consisting of immersing the Sensor in cold water at
not penetrate.
0°C for 1 hour followed by hot water at 70°C for 1 hour.

5
Limited ingress of dust permitted
(no harmful deposit). * 2. Precautions on OMRON Testing
Operating conditions for E2F Proximity Sensors: Underwater within 10 m.
(1) No penetration of water when immersed in water for 1 hour at two
atmospheric pressures.
6 Totally protected against ingress of dust. (2) Satisfies sensing distance and insulation resistance performance
specifications after the heat shock cycle described in *1 is repeated
20 times
Second Symbol: Degree of Protection Against Water
Code Degree of protection Examination method
0 No particular protection No protection No test
Rain
Protected against vertically falling Spray water downwards in vertical direction for 200 mm
1
drops of water. 10 minutes using a water-dripping test device.

Rain
Tilt by 15° and spray water for 10 minutes
Protected against vertically falling drops of water 200 mm
2 (2.5 minutes in each direction) using a water-dripping 15°
with enclosure tilted 15° from the vertical.
test device.
Flow per water
Rain Spray water up to 60° in both directions from the spray hole: 0.07

3 Protected against sprays to 60° from the vertical. vertical axis for 10 minutes using the test device
shown below.

Water splash from all directions Flow per water spray

hole: 0.07 l/min
Protected against water splashed from Spray water from all directions for 10 minutes using
4
all directions; limited ingress permitted. the test device shown below.

Housing jets from all directions 12.5 l/min

Spray water from all directions for one minute per m2 2.53 m
Protected against low-pressure jets of water from
5 of external surface area and for a total time of no less
all directions; limited ingress permitted.
than 3 minutes using the test device shown below.
Discharging nozzle dia.: 6.3

Strong hosing jets from all 100 l/min

2.53 m
directions Spray water from all directions for one minute per m2
Protected against strong jets of water, e.g. for use
6 of external surface area and for a total time of no less
on ship decks; limited ingress permitted.
than 3 minutes using the test device shown below.
Discharging nozzle dia.: 12.5

Temporary immersion
7
* 1 Protected against the effects of immersion between
15 cm and 1 m.
Submerge for 30 minutes at the depth of 1 m
(if the device is located lower than 850 mm).
1m

Continuous immersion

8 * 2 Protected against long periods of immersion

under pressure.
Test according to the conditions agreed upon between the manufacturer
and user.

90°
IP69K Degree of Protection 60°
IP69K is a standard for protection again ingress of high-temperature, high-pressure water defined in the German standard
DIN 40050 Part 9. 30°
The test piece is sprayed with water at 80° at 80 to 100 bars with a nozzle of the specified shape. 10 to 15 cm
The test piece is separated from the nozzle by 10 to 15 cm and water is sprayed for 30 s each at 0°, 30°, 60°, and 90° while
the test piece is rotated on a horizontal plane.
Note: The degree of protection given in Connector ratings and performance specifications may not be met if the Connectors are 0°

not connected correctly or if connectors (including e-CON connectors) that have no protection are used.

I N D U S T R I A L C O N N E C T O R S C ATA L O G 11
 Network Connector Variations 2
Benefits of Connector Units 4
Industrial Ethernet Connectors 7
M12 Smartclick Connectors 8

Industrial Standards
INDEX
10
12

Connectors Industrial Ethernet Connectors 14

Catalog XS5/XS6 14

Sensor I/O Connectors 30

Introduction to Sensor I/O Connectors 30
XS5 32
XW3D 61
XS2 65
XW3B 94
XS3 101
XN2 122

DeviceNet Peripherals 126

Communications Peripherals for Standard Slaves 126
I/O Peripherals for Standard Slaves 132
Communications Peripherals for
Environment-resistive Slaves 136
I/O Peripherals for Environment-resistive Slaves 147
Power Supply Peripherals for
Environment-resistive Slaves 148

Standard-compliant Models 150

Model Index 156

CC-Link is a registered trademark of Mitsubishi Electric Corporation.

The trademark is managed by the CC-Link Partner Association. is a registered trademark and patented technology,
licensed by Beckhoff Automation GmbH, Germany.

12 I N D U S T R I A L C O N N E C T O R S C ATA L O G
I N D U S T R I A L C O N N E C T O R S C ATA L O G 13
 Industrial Ethernet Cables

XS5/XS6
Cables and Connectors for
EtherCAT® and Other
Industrial Ethernet Networks
CAT6a Ethernet patch cables
• For in-cabinet use
• LSZH with standard RJ45 plugs

CAT5e Ethernet patch cables

• For out-of-cabinet use
• PUR with standard RJ45 plugs
• PVC with rugged RJ45 plugs
• PVC with M12 SmartClick plugs

■ Connection Examples

ADR

ADR

ADR

Control panel

Ideal for in-cabinet Ideal for out-of-cabinet

XS6W-6LSZH XS6W-5PUR XS5 XS6

Standard Connectors Rugged Connectors Rugged Assembly Connectors

Standard Connectors XS5

M12 Connectors

14
 XS5/CS6
■ Features
Cables with Standard RJ45 Connectors Refer to page 17 for details.
• The lineup features LSZH cables for in-panel wiring and PUR cables for wiring outside of panels.
*
• The Standard RJ45 Connectors reduce cable routing space.
- Outer diameter: 5.8 mm
- 4-pair AWG27 (LSZH) or AWG26 (PUR)
• Cable colors include blue, yellow, or green.
• LSZH cables are available in 12 lengths from 0.2 to 20 m and PUR cables are available in 10 lengths from 0.5 to 20 m.
• Double-shielded cables with overall braiding and individual foil shield on each wire pair to reduce EMC interference in industrial
environments.

* Low-smoke zero-halogen cables.

Shape of RJ45 Connector LSZH Cable with Double Shield

Overall braiding and individual foil shield on each wire pair

Cables with Rugged RJ45 Connectors Refer to page 20 for details.

• Tough latches and RJ45 connectors with strong cable holding strength are used to enable connections outside of control panels.
• Quad AWG22 cable with PVC cover of 6.5 mm outer diameter.
• Double-shielded cables with overall braiding and individual foil shield to reduce EMC interference in industrial environments.

Shape of RJ45 Connector PVC Cable with Double Shield

Tough latch Overall braiding and individual foil shield

Assembly Connectors
You can easily assemble Ethernet cables onsite without crimping tools or other special tools.
Refer to page 27 for the assembly procedure.

● Cable Extension Length

Standard Connectors (RJ45 Connectors) Rugged Connectors (RJ45 Connectors)
58 mm 89 mm

Minimum cable Minimum cable bending

bending radius: radius: 40 mm
25 mm

15
 XS5/CS6

Cables with M12 Connectors Refer to page 20 for details.

• Resistance to harsh environments with IP67 protection.

• SmartClick Connectors that provide one-step (1/8th turn) connection are used (compatible with standard M12 screw connectors).
• A wide range of variations, such as cables with right-angle connectors and PCB connectors.
• Cables with sockets and robot cables were added to the series.

Shape of M12 Connector PVC Cable with Double Shield

Overall braiding and individual foil shield

Shield structure

Shield Effectiveness Data for Rugged RJ45 Connectors and Waterproof M12 Connectors
The following data is the results of OMRON testing. Shield effectiveness may vary for your environment and application conditions.

● Comparison of Shield Effectiveness with Product without a Double Shield

The following table shows the differences with a structure without a double shield. Higher numeric values show greater shield
effectiveness.
Frequency (MHz)
Shield structure
0.5 1 5 10 30
Product with single shield 53 dB 49 dB 35 dB 25 dB 17 dB
Product with a double shield (XS5@-T, Category 5E) 61 dB 58 dB 43 dB 31 dB 27 dB

• SmartClick is registered trademark of OMRON Corporation.

• EtherCAT® is a registered trademark and patented technology, licensed by Beckhoff Automation GmbH, Germany.

16
 XS5/CS6

Cables with Standard RJ45 Connectors

■ Model Number Legend
Use this legend when determining the product specifications from the model number. Choose from the model numbers listed in Ordering
Information when ordering.

X S6 W -@ @ @ @ @ 8 SS @ @ @ @ C M- @
1 2 3 4 5 6

1 Transmission Characteristics
5: Category 5
6: Category 6A

2 Sheath Material

LSZH: LSZH
PUR: PUR

3 Number of Pins

8: 8 pins

4 Cable Attachment Direction

SS: Straight/Straight

5 Cable Length*

20: 0.2 m
30: 0.3 m
50: 0.5 m
100: 1 m
150: 1.5 m
200: 2 m
300: 3 m
500: 5 m
750: 7.5 m
1000: 10 m
1500: 15 m
2000: 20 m

6 Sheath Color
B: Blue
Y: Yellow
G: Green

* PUR cables are not available for 0.2-m and 0.3-m cables.

17
 XS5/CS6
■ Ordering Information
Cable sheath
Appearance Type Category Cable color Cable length (m) Model
material
0.2 XS6W-6LSZH8SS20CM-B
0.3 XS6W-6LSZH8SS30CM-B
0.5 XS6W-6LSZH8SS50CM-B
1 XS6W-6LSZH8SS100CM-B
1.5 XS6W-6LSZH8SS150CM-B
2 XS6W-6LSZH8SS200CM-B
Blue
3 XS6W-6LSZH8SS300CM-B
5 XS6W-6LSZH8SS500CM-B
7.5 XS6W-6LSZH8SS750CM-B
10 XS6W-6LSZH8SS1000CM-B
15 XS6W-6LSZH8SS1500CM-B
20 XS6W-6LSZH8SS2000CM-B
0.2 XS6W-6LSZH8SS20CM-Y
0.3 XS6W-6LSZH8SS30CM-Y
0.5 XS6W-6LSZH8SS50CM-Y
1 XS6W-6LSZH8SS100CM-Y
1.5 XS6W-6LSZH8SS150CM-Y
2 XS6W-6LSZH8SS200CM-Y
Cat.6a LSZH Yellow
3 XS6W-6LSZH8SS300CM-Y
5 XS6W-6LSZH8SS500CM-Y
7.5 XS6W-6LSZH8SS750CM-Y
10 XS6W-6LSZH8SS1000CM-Y
Cable with 15 XS6W-6LSZH8SS1500CM-Y
Connectors on Both
Ends (RJ45/RJ45) 20 XS6W-6LSZH8SS2000CM-Y
0.2 XS6W-6LSZH8SS20CM-G
0.3 XS6W-6LSZH8SS30CM-G
0.5 XS6W-6LSZH8SS50CM-G
1 XS6W-6LSZH8SS100CM-G
1.5 XS6W-6LSZH8SS150CM-G
2 XS6W-6LSZH8SS200CM-G
Green
3 XS6W-6LSZH8SS300CM-G
5 XS6W-6LSZH8SS500CM-G
7.5 XS6W-6LSZH8SS750CM-G
10 XS6W-6LSZH8SS1000CM-G
15 XS6W-6LSZH8SS1500CM-G
20 XS6W-6LSZH8SS2000CM-G
0.5 XS6W-5PUR8SS50CM-G
1 XS6W-5PUR8SS100CM-G
1.5 XS6W-5PUR8SS150CM-G
2 XS6W-5PUR8SS200CM-G
3 XS6W-5PUR8SS300CM-G
Cat.5 PUR Green
5 XS6W-5PUR8SS500CM-G
7.5 XS6W-5PUR8SS750CM-G
10 XS6W-5PUR8SS1000CM-G
15 XS6W-5PUR8SS1500CM-G
20 XS6W-5PUR8SS2000CM-G

18
 XS5/CS6
■ Specifications
Cable with Connectors on Both Ends Cable with Connectors on Both Ends
Type
(RJ45/RJ45)/LSZH (RJ45/RJ45)/PUR
Item Model XS6W-6LSZH8SS@@@@CM-@ XS6W-5PUR8SS@@@@CM-G
Rated current 1 A (at 50°C)
Withstand voltage 1,000 VDC for 60 s (leakage current: 1 mA max.)
Ambient operating
−20 to 60°C −40 to 85°C
temperature
Ambient storage
−20 to 60°C −40 to 85°C
temperature
Ambient installation
0 to 50°C −10 to 60°C
temperature
Protective structure IP20

■ Materials and Finish

● Connectors
Cable with Connectors on Both Ends Cable with Connectors on Both Ends
Type
(RJ45/RJ45)/LSZH (RJ45/RJ45)/PUR
Item Model XS6W-6LSZH8SS@@@@CM-@ XS6W-5PUR8SS@@@@CM-G
Connector housing PC resin (UL94V-0)/transparent
Contacts Phosphor bronze/nickel base, gold plated (0.8 μm)
Shield Brass/nickel plated
Cover
(structured to prevent the LSZH: Blue, yellow, or green PUR: Green
tab from breaking)
Marking tube PVC resin (UL94V-0)/transparent

● Cables
Cable with Connectors on Both Ends Cable with Connectors on Both Ends
Type
(RJ45/RJ45)/LSZH (RJ45/RJ45)/PUR
Item Model XS6W-6LSZH8SS@@@@CM-@ XS6W-5PUR8SS@@@@CM-G
Compliant standard IEC 60332-1 /UL1581 FT2 IEC 60332-1 /UL1581 FT2
Number of cores/gauge 4 × 2 × AWG27 0.1 mm2 4 × 2 × AWG26 0.13 mm2
Outer diameter*1 5.8 mm
*2. Sheath.
Sheath color*2 Blue, yellow, or green Green
Sheath material LSZH PUR *1. Outer diameter.

Shield structure Double shield S/FTP Double shield SF/UTP

■ Dimensions (Unit: mm)

● Cable with Connectors on Both Ends (RJ45/RJ45)

Wiring
XS6W-6LSZH8SS@@@@CM-@
RJ45 RJ45
XS6W-5PUR8SS@@@@CM-G 1 1
2 2
3 3
4 4
5 5
6 6
7 7
8 8
Shield Shield

L (cable length)

(14)

13.2 38.5 18 18 38.5

Marking tube
Note. External dimensions are the same for all cable materials.

19
 XS5/CS6

Cables with Rugged RJ45 Connectors and Cables with M12 Connectors
■ Model Number Legend
Use this legend when determining the product specifications from the model number. Choose from the model numbers listed in Ordering
Information when ordering.
● Cable with Connectors ● RJ45 Assembly Connectors

XS 5@ - T 4 2 @ - @ M@ - @ @ XS6G-T 4 2 1-1
1 2 3 4 5 6 7 8 1 2 3 4 5

1 Connector Shape 1 Type

H: Cable with plug on one end T: Ethernet

W: Cable with connectors on both ends
2 Number of Pins
2 Typ 4: 4 pins
T: Ethernet (mating part: M12 D coding)
3 Contact Plating Specification
3 Number of Pins 2: Gold plating, 0.4 μm
4: 4 pins
4 Cable Attachment Direction
4 Contact Plating Specification 1: Straight
2: Gold plating, 0.4 μm
5 Degree of Protection

5 Cable Attachment Direction (M12 Connectors) 1: IP20

1: Straight
2: Right angle ● M12 Connectors for Panel Mounting
6 Cable Length
X S 5 P - T 4 2 @ -@
A: 0.3 m
1 2 3 4 5
B: 0.5 m
C: 1 m
1 Type
D: 2 m
T: Ethernet (mating part: M12 D coding)
E: 3 m
G: 5 m 2 Number of Pins
J: 10 m 4: 4 pins
K: 15 m
3 Plating Specification
7 Connector Shape 2: Gold plating, 0.4 μm
0: M12 plug on one end
4 Mounting Method
1: Connectors on both ends: M12 socket/M12 plug
6: Rear locking
2: Connectors on both ends: M12 plug/M12 plug
7: Front locking
C: Connectors on both ends: M12 plug/RJ45 plug
D: Connectors on both ends: RJ45 plug/RJ45 plug 5 Terminal Shape
E: Connectors on both ends: M12 socket/RJ45 plug 1: DIP terminals
5: Cable with loose wires (0.5 m)
8 Cable Specification
K: Standard cable
KR: Robot cable

20
 XS5/CS6
■ Ordering Information
Appearance Cable type Type Cable length (m) Model
0.5 XS5H-T421-BM0-K
1 XS5H-T421-CM0-K
2 XS5H-T421-DM0-K
Cable with Plug on One End 3 XS5H-T421-EM0-K
(M12 Straight)
5 XS5H-T421-GM0-K
10 XS5H-T421-JM0-K
15 XS5H-T421-KM0-K
0.5 XS5W-T421-BM2-K
1 XS5W-T421-CM2-K
2 XS5W-T421-DM2-K
Cable with Plugs on Both Ends
3 XS5W-T421-EM2-K
(M12 Straight/M12 Straight)
5 XS5W-T421-GM2-K
10 XS5W-T421-JM2-K
15 XS5W-T421-KM2-K
0.3 XS5W-T421-AMC-K
0.5 XS5W-T421-BMC-K
1 XS5W-T421-CMC-K
Cable with Plugs on Both Ends 2 XS5W-T421-DMC-K
(M12 Straight/RJ45) 3 XS5W-T421-EMC-K
5 XS5W-T421-GMC-K
10 XS5W-T421-JMC-K
15 XS5W-T421-KMC-K
0.5 XS5H-T422-BM0-K
1 XS5H-T422-CM0-K
2 XS5H-T422-DM0-K
Cable with Plug on One End 3 XS5H-T422-EM0-K
(M12 Right-angle)
5 XS5H-T422-GM0-K
10 XS5H-T422-JM0-K
15 XS5H-T422-KM0-K
0.5 XS5W-T422-BM2-K
1 XS5W-T422-CM2-K
2 XS5W-T422-DM2-K
Cable with Plugs on Both Ends 3 XS5W-T422-EM2-K
Standard Cables (M12 Right-angle/M12 Right-angle)
5 XS5W-T422-GM2-K
10 XS5W-T422-JM2-K
15 XS5W-T422-KM2-K
0.3 XS5W-T422-AMC-K
0.5 XS5W-T422-BMC-K
1 XS5W-T422-CMC-K
Cable with Plugs on Both Ends 2 XS5W-T422-DMC-K
(M12 Right-angle/RJ45) 3 XS5W-T422-EMC-K
5 XS5W-T422-GMC-K
10 XS5W-T422-JMC-K
15 XS5W-T422-KMC-K
0.3 XS5W-T421-AMD-K
0.5 XS5W-T421-BMD-K
1 XS5W-T421-CMD-K
Cable with Plugs on Both Ends 2 XS5W-T421-DMD-K
(RJ45/RJ45) 3 XS5W-T421-EMD-K
5 XS5W-T421-GMD-K
10 XS5W-T421-JMD-K
15 XS5W-T421-KMD-K
0.5 XS5W-T421-BM1-K
1 XS5W-T421-CM1-K
Cable with Plug on One End and Socket on 2 XS5W-T421-DM1-K
Other End 3 XS5W-T421-EM1-K
(M12 Straight/M12 Straight) 5 XS5W-T421-GM1-K
10 XS5W-T421-JM1-K
15 XS5W-T421-KM1-K
0.5 XS5W-T421-BME-K
1 XS5W-T421-CME-K
Cable with Plug on One End and Socket on 2 XS5W-T421-DME-K
Other End 3 XS5W-T421-EME-K
(M12 Straight/RJ45) 5 XS5W-T421-GME-K
10 XS5W-T421-JME-K
15 XS5W-T421-KME-K

21
 XS5/CS6

Appearance Cable type Type Cable length (m) Model

0.5 XS5W-T421-BM1-KR
1 XS5W-T421-CM1-KR
Cable with Plug on One End and Socket on 2 XS5W-T421-DM1-KR
Other End 3 XS5W-T421-EM1-KR
(M12 Straight/M12 Straight) 5 XS5W-T421-GM1-KR
10 XS5W-T421-JM1-KR
15 XS5W-T421-KM1-KR
0.5 XS5W-T421-BM2-KR
1 XS5W-T421-CM2-KR
2 XS5W-T421-DM2-KR
Cable with Plugs on Both Ends
3 XS5W-T421-EM2-KR
(M12 Straight/M12 Straight)
5 XS5W-T421-GM2-KR
10 XS5W-T421-JM2-KR
15 XS5W-T421-KM2-KR
Robot Cables
0.5 XS5W-T421-BMC-KR
1 XS5W-T421-CMC-KR
2 XS5W-T421-DMC-KR
Cable with Plugs on Both Ends
3 XS5W-T421-EMC-KR
(M12 Straight/RJ45)
5 XS5W-T421-GMC-KR
10 XS5W-T421-JMC-KR
15 XS5W-T421-KMC-KR
0.5 XS5W-T421-BMD-KR
1 XS5W-T421-CMD-KR
2 XS5W-T421-DMD-KR
Cable with Plugs on Both Ends
3 XS5W-T421-EMD-KR
(RJ45/RJ45)
5 XS5W-T421-GMD-KR
10 XS5W-T421-JMD-KR
15 XS5W-T421-KMD-KR

RJ45 Assembly Connector --- XS6G-T421-1

Rear locking 0.5 XS5P-T426-5

Standard Cables M12 Connector for Panel
Mounting
Front locking 0.5 XS5P-T427-5

M12 Panel-mounting PCB Straight Terminals --- XS5P-T426-1

● Cable Bending Data for Robot Cables (XS5W-T421-@M@-KR)

The following data is the results of OMRON testing for cable bending test conditions. The number of bends may vary for your
environment and application conditions.
Cableveyor Test 90° Bending Test
Number of bends: 20 million min. Number of bends: 6 million min.

Travel distance

Cable secured to end

Cableveyor Cable secured to end

Travel speed: Approx. 120 m/min Roller

Travel distance: 1 m
Cableveyor radius: 75 mm
Cable

Bending angle: ±90° Weight

Speed: Approx. 30 bends/min
Roller radius: 60 mm
Weight: 500 g

22
 XS5/CS6
■ Specifications
Cable with Cable with
Cable with Plug on One Cable with Plug on One Cable with M12 Panel-
Cable with M12 Connec-
Plugs on Both End and Plugs on Both End and Plugs on Both RJ45 Assembly mounting PCB
Type Plug on One tor for Panel
Ends Socket on Ends Socket on Ends Connector Straight
End (M12) Mounting
(M12/M12) Other End (M12/RJ45) Other End (RJ45/RJ45) Terminals
(M12/M12) (M12/RJ45)
XS5W XS5W XS5W XS5W
XS5H XS5W XS6G XS5P
Item Model -T42@-@M2-K, -T42@-@M1-K, -T42@-@MC-K, -T421-@MD-K, XS5P-T42@-5
-T42@-@M0-K -T421-@ME-K -T421-1 -T426-1
-KR -KR -KR -KR
Rated current 3A 2.5 A 4A
Rated voltage 30 V 125 VDC
Contact resistance 40 mΩ max.
Insulation
1,000 MΩ min. 500 MΩ min. 1,000 MΩ min.
resistance
1,500 VAC for 60 s
Withstand voltage 1,000 VAC for 60 s (leakage current: 1 mA max.)
(leakage current: 1 mA max.)
Ambient operating
−25 to 70°C
temperature
Ambient storage
−25 to 70°C
temperature
Protective
M12: IEC IP67, RJ45: IEC IP20
structure

■ Materials and Finish

● Connectors
Model M12 RJ45
Item XS5H and XS5W XS5P-T42@-5 XS5P-T426-1 XS5W and XS6G
Contact blocks PBT resin (UL94V-0)/light gray PA resin (UL94V-0)/black PA resin (UL94V-0)/black
Brass/nickel base, gold plated Phosphor bronze/nickel base,
Contacts Phosphor bronze/nickel base, gold plated (0.4 μm)
(0.4 μm) gold plated (1.4 μm)
Anchors Zinc diecast/nickel plating ---
Anchors (tabs) SUS ---
Straight connector: Soft PBT
resin (UL94V-0)/black
Cover ---
Right-angle connector:
TPC resin/black
Sealing resin --- Epoxy resin ---
O-rings Rubber ---
Phosphor bronze/nickel base,
Grounding fixture --- ---
tin plated (2.0 μm)
Anchor cover --- SUS ---
Nuts --- Brass/nickel plated ---

● Cables
Model
Standard Cables Robot Cables
Item
Compliant standard UL CM
Category Category 5e
Number of cores/gauge 4 × AWG22 0.3 mm2 (7/0.26) 4 × AWG22 0.3 mm2 (7/24/0.05)
Outer diameter*1 6.5 dia. *2. Sheath.
Sheath color*2 Light blue
*1. Outer diameter.
Sheath material PVC
Shield structure Double shield SF/UTP
Note. For the XS5H and XS5W, cables are available only with connectors attached.

23
 XS5/CS6
■ Dimensions (Unit: mm)

● Cable with Plug on One End (M12 Straight) Wiring

XS5H-T421-@M0-K Terminal No. Color
1 Yellow
2 White
3 Orange
4 Blue
L (cable length)
44.7
2 1

2 1
14.9 dia.
3 4

3 4
M12 × 1
(Plug)

● Cable with Plugs on Both End (M12 Straight/M12 Straight) Wiring

XS5W-T421-@M2-K M12 straight M12 straight
XS5W-T421-@M2-KR 1 1
2 2
3 3
4 4
Shield Shield

L (cable length)
44.7 44.7
2 1 4 3
4 3

2 1
14.9 dia. 14.9 dia. 1 2

3 4

3 4 1 2
M12 × 1 M12 × 1
(Plug) (Plug)

● Cable with Plugs on Both Ends (M12 Straight/RJ45) Wiring

XS5W-T421-@MC-K M12 straight RJ45
XS5W-T421-@MC-KR 1 1
2 3
3 2
4 6
Shield Shield
L (cable length)
44.7 54.7
2 1

2 1
14.9 dia.
3 4

3 4
M12 × 1
(Plug)
RJ45

● Cable with Plug on One End and Socket on Other End (M12 Straight/M12 Straight) Wiring
XS5W-T421-@M1-K M12 straight M12 straight
XS5W-T421-@M1-KR 1 1
2 2
3 3
4 4
Shield Shield
L (cable length)
44.7 50.7
2 1 3 4
4 3

2 1
14.9 dia. 14.9 dia. 2 1

3 4

3 4 2 1
M12 × 1 M12×1
(Plug) (Socket)

● Cable with Plug on One End and Socket on Other End (M12 Straight/RJ45) Wiring
XS5W-T421-@ME-K M12 straight RJ45
1 1
2 3
3 2
4 6
Shield Shield
L (cable length)
50.7 54.7
1 2

1 2
14.9 dia.
4 3

4 3

(Socket) M12 × 1
RJ45

24
 XS5/CS6

● Cable with Plug One End (M12 Right-angle) Wiring

XS5H-T422-@M0-K Terminal No. Color
1 Yellow
2 White
3 Orange
4 Blue
L (cable length)
22.5

32.3

14.9 dia.
M12 × 1

1 4
1
4
2

2 3

(Plug)

● Cable with Plugs on Both Ends (M12 Right-angle/M12 Right-angle) Wiring

XS5W-T422-@M2-K M12 right angle M12 right angle
1 1
2 2
L (cable length) 3 3
4 4
22.5 22.5 Shield Shield

32.3 32.3

14.9 dia. 14.9 dia.

M12 × 1 M12 × 1

1 4 3 2

3
1

2
4
4
2

1
3

2 3 4 1

(Plug) (Plug)

● Cable with Plugs on Both Ends (M12 Right-angle/RJ45)

XS5W-T422-@MC-K
L (cable length)
22.5 54.7

32.3

RJ45

14.9 dia.
M12 × 1 Wiring
1 4 M12 right angle RJ45
1 1
1

2 3
4
2

3 2
3

2 3 4 6
Shield Shield
(Plug)

● Cable with Plugs on Both Ends (RJ45/RJ45) Wiring

XS5W-T421-@MD-K RJ45 RJ45
1 1
XS5W-T421-@MD-KR 2 2
3 3
6 6
Shield Shield
L (cable length)
54.7 54.7

RJ45 RJ45

25
 XS5/CS6

● RJ45 Assembly Connector

XS6G-T421-1 52.6

11.8 11.3

8.1
Contact 6 Contact 1
Contact 2
Contact 3
Applicable wires
Sheath outer diameter: 6.1 to 6.9 mm
Core size: AWG22 to AWG24 (stranded wires)
AWG22 to AWG23 (solid wires)
Insulation outer diameter: 1.6 mm max.

● M12 Connector for Panel Mounting

Wiring
XS5P-T42@-5
XS5P-T426-5 (Rear Locking) Terminal No. Color
1 Yellow
M12 × 1 PG9 2 White
18
17 2.8 Orange
500 White 3 Orange
4 Blue
18 14.6 dia. 20

(20) Blue Yellow

2.5 10±3
11.9 Panel Cutout Dimension
(Socket)
22.1
15.3 +0.1
0 dia.

XS5P-T427-5 (Front Locking)

Panel thickness
t = 1 to 4
M12 × 1 2.8 17
18 PG9 500 Orange White
Note 1: The panel cutout dimen-
20 13.9 dia. 18
sion is the same for
Front-locking and Rear-
(20) Blue locking Connectors.
10±3 Yellow
2.5 Note 2: Rotational positioning is
(Socket) 10.5
22.1 not possible for connec-
tor rotation.

● M12 Panel-mounting PCB Straight Terminals

XS5P-T426-1 Mounting Hole Dimensions Mounting Hole Dimensions
(D Cut Structure)
19.9 10.6 +0.2
0
10.4
14
Pin No. M12×1 B
2.5

5.3 +0.1
0
15
A A C C

B
(Socket) 2.5
1.2±0.04 dia. × 45° 1.2±0.04 dia. × 45°
0.5 min.
2 to 3 2 to 3
16.5 dia. 14.6 dia.
12.2±0.05 dia. 12.2±0.05 dia.
Cross-section Diagram A-A Cross-section Diagram C-C
3 0.5 min.

Cross-section Diagram B-B

Panel Processing Dimensions

5±0.05 dia.
45°±1°
5±0.05
Four, 1.2 +0.1
0 dia. 7.05±0.05
Three, 1.4 +0.1
0 dia.
4.5±0.05
1 +0.1
0 dia.
8.5±0.05

26
 XS5/CS6
■ Assembly Procedure
● RJ45 Assembly Connectors ● M12 Panel-mounting PCB Straight Terminals
XS6G-T421-1 XS5P-T426-1
1. Pass the cable through the cable Confirming the Number of Parts
clamp and the connector housing The following four parts are included in the package when it is
24 mm delivered.
2. Strip the cable sheath and ground 13 mm Panel-mounting Parts PCB-mounting Part
braiding to the correct lengths. 1. Anchor 2. O-Ring 3. Nut 4. Connector

3. Follow the color codes and prepare

to insert the wires into the splice
piece.

4. Insert the wires into the splice piece

for the length of the splice piece. Assembly Procedure
1. Mount the connector to the PCB.
5. Place the splice piece into the RJ45 2. Attach the anchor to the panel with the nut.
data module and engage it. Mounting the Connector to the PCB Mounting the Anchor to the Panel

6. Place the data module and the Anchor

splice piece on the IDC assembly

PCB Panel
housing. Nut
*Tightening torque: 1 N·m
7. Press the data module and the IDC
assembly housing together and use 3. Attach the connector that you mounted to the PCB to the panel.
pliers or a similar device to make * Make sure that the connector and anchor are oriented correctly.
the insulation displacement contact. Attachment

8. Remove the data module from the

IDC assembly housing.

9. Place the upper screen plate on the

data module and press it over the
5 mm
ground braiding of the cable.

10. Place the lower screen plate on the

bottom of the data module, align it Align the flat surface on the anchor with
the grounding fixture terminal.
with the upper screen place, and
latch it until you hear it click into 4. Temporarily mount the O-ring to the top of the connector at
place. the mating surface.
Temporary Mounting O-ring
11. Slide the housing that you placed of the O-Ring
around the cable in step 1 up to the
data module and latch it until you
hear it click into place.

12. Tighten the cable clamp.

Pin Assignments 5. Mate the Connector Waterproof Cover (XS2Z-22, sold sepa-
Pin Assignments for Fast Ethernet 10/100 Mbps rately) or the Partner Connector Plug (XS5H-T42@-@M0-K,
Wire color sold separately) and press the O-ring to the O-ring position
Function/Signal Industrial EIA/TIA EIA/TIA Pin No.
after mounting.
Ethernet 568A 568B
Mounting the O-Ring
Transmission Data+/TD+ YE WH/GN WH/OG 1
Transmission Data-/TD− OG GN OG 2 O-Ring Position after Mounting

Receiver Data/RD+ WH WH/OG WH 3

Receiver Data/RD− BU OG GN 6

● Connector Waterproof Cover (Sold Separately)

XS2Z-22

* Tightening torque: 0.39 to 0.49 N•m

27
 XS5/CS6
■ Safety Precautions

Precautions for Correct Use

Do not use the Connectors in an atmosphere or environment
that exceeds the specifications.

● Connector Connection and Disconnection ● Handling Precautions

• When connecting or disconnecting Connectors, be sure to • Do not pull on the Connectors or cables with excessive force.
hold the Connectors. Do not install the Connectors with a load placed directly on the
• Do not hold the cable when disconnecting Connectors. joint or at the point where the wires connect to the Connector.
• When joining Connectors, be sure to insert the plug all the way The Connector may be damaged or the wires in the cable may
to the back of the socket before attempting to lock the be disconnected.
Connectors. • Lay the cable where it will not be stepped on to prevent the
• Do not use tools of any sort to join the Connectors. Always use wires in the cable from being disconnected and to protect the
your hands. Pliers or other tools may damage the Connectors. Connectors from being damaged. If the cable must be placed
where it will be stepped on, install a protective cover.
● Wiring • When bending cables, do not exceed the cable specifications.
Lay the cables so that external force is not applied to the
Connectors. Otherwise, the degree of protection (IP67) may not
be achieved.

● Degree of Protection for M12/Smartclick Connectors

• The degree of protection of Connectors (IP67) is not for a fully
watertight structure. Do not use the Connectors underwater.
• Do not step on or place any objects on the Connectors. Doing
so may damage the Connectors.

28
MEMO

29
 XS5/XS2/XW3 FA Connectors
Wiring System Configuration

Sensor End Relay Cable

Using Limit Switches and Sensors with Connectors
Connector with Cable XS5W (Smartclick)
Proximity Sensor XS2W (Screw-mounting)
(Direct Connection Type)
E2E

(Connector-Terminal Connection Type)

E2E

Compact Limit Switch (Multiple XS5W,XS2W can be used to extend the cable.)
(Connector-Terminal D4CC
Connection Type)
Connector Assembly
(IDC,Crimping, Soldering, Screw-mounting)
Compact Enclosed Switch
(Connector-Terminal Connection Type)
XS5C (Smartclick) XS5H (Smartclick)
D4E-@N XS2H (Screw-mounting)
XS2C (Screw-mounting)
Enabling Connectors to Be Used with Sensors
Connector Assembly (IDC,Crimping, Soldering, Screw-mounting)
XS5G (Smartclick)
XS2G (Screw-mounting)
Connector with Cable
+ Connector Assembly
Used to enable connectors (Connector-Terminal connection
(IDC,Crimping, Soldering, Screw-mounting)
types) to be used with pre-wired Sensors. XS5F (Smartclick) XS5G(Smartclick)
XS2F (Screw-mounting) XS2G (Screw-mounting)
Making Sensors with Cables (Sensor Manufacturers)
Connector with Cable
XS5H,XS2H

Connector Assembly
(Crimping, Soldering, Screw-mounting)
Used to enable connectors (Connector-Terminal connection
types) to be integrated with the Sensor body. XS5C (Smartclick) XS5G (Smartclick)
XS2C (Screw-mounting) XS2G (Screw-mounting)
Sensor-embedded Connector

XS2M
(Embedded Plug with
Screw Threads)

Connector Assembly
XS2M
(Embedded Plug without
(IDC,Crimping, Soldering, Screw-mounting)
Screw Threads) XS5C (Smartclick)
Used to enable connectors (direct connection types) to be XS2C (Screw-mounting)
integrated with the Sensor body.
Mounting to Panels
Panel-mounting Connector
Connector with Cable
XS2M
(Flange-mounting) XS5F (Smartclick)
XS2F (Screw-mounting)

XS5M,XS2M
(Screw-mounting)

30
 ( indicates mating connectors, and indicates wiring connections.)

Terminal Box, PCB Type ■ Personal Computer

■ PT (Programmable Terminal)
Connector Terminal Box
XS3D (Smartclick)
XS3B (Screw-mounting)

Refer to page 61 for details on the

XW3D and to page 94 for details on the
XW3B.
Host Link Cable
Terminal Box Connector XW2Z

Y-Joint XS5P,XS2P

XS5R (Smartclick)
XS2R (Screw-mounting)

Refer to your OMRON website for

details.

Used to wire two Sensors to a single Used to enable using connectors for
cable. terminal boxes.

Connecting Cable
Connector-Terminal Block Conversion
Units XW2Z
XW2R(PLCs,General-purpose devices)
XW2D (slim model)
XW2C (with power supply common terminal)
XW2B (general-purpose model) Programmable
XW2F (with screwless clamp terminals)
Controller

Crimp
terminal
wiring
Terminal Block
(Commercially Available)

31
 Round Water-resistant Connectors (M12 Smartclick)

XS5
Round Water-resistive Smartclick
Connectors That Reduce Installation
Work
• A newly developed lock mechanism that is compatible with round M12
connectors.
• Simply insert the Connectors, then turn them approximately 1/8 of a turn
to lock.
• A positive click indicates locking.
• Features the same degree of protection (IP67) as M12 connectors.
• A full line-up of models is planned.
• Connectors with Cables are UL approved.

Refer to Safety Precautions on page 55.

Ratings and Specifications

Rated current 4A
Rated voltage 250 VDC
Contact resistance (connector) 40 mΩ max. (20 mV max., 100 mA max.)
Insulation resistance 1,000 MΩ min. (at 500 VDC)
Dielectric strength (connector) 1,500 VAC for 1 min (leakage current: 1 mA max.)
Degree of protection IP67 (IEC60529)
Insertion tolerance 50 times min.
Lock strength Tensile: 100 N/15 s, Torsion: 1 N·m/15 s
Cable holding strength Tensile: 100 N/15 s, Torsion: 1 N·m/15 s (for cable diameter of 6 mm) *2
Lock operating force 0.1 to 0.25 N·m
Ambient operating temperature range −25 to 70°C
Ambient humidity range 20% to 85%
Number of pressure-weld repairs *1 10 times max. (Limited to the same external diameter and wire diameter.)
*1. Only XS5C/G (IDC models)
*2. Refer to product specifications for details.

32
 XS5
Materials and Finishes
Model XS5C/G XS5C/G XS5C/G
XS5F/H/W XS5R XS5M/P
Item (Crimping, Soldering) (Screw-on) (IDC models)
Phosphor bronze Phosphor bronze
Material Phosphor bronze Phosphor bronze Brass Phosphor bronze
or Brass or Brass
Contacts
Finish Nickel base, 0.4-μm gold plating Nickel base, 0.15-
μm gold plating
Fixtures Nickel-plated zinc alloy
Fixtures (Lock) * Stainless
Pin block PBT resin (UL94V-0)
O-ring Rubber
Overmolding/Cover Soft PBT resin (UL94V-0) --- PBT resin (UL94V-0)
UL AWM2464 CL3, 6 mm dia.,
Fire-retardant,
AWG20 (0.5mm2) ---
Robot cable
Structure: 0.08 mm/110 wires
Oil-resistant 6 mm dia.
Cable polyurethane AWG20 (0.5mm2) ---
cable Structure: 0.12 mm/45 wires
6.6 mm dia.
Spatter-resis-
AWG20 (0.5mm2) ---
tant Cable
Structure: 0.08 mm/100 wires
Epoxy resin
Seal resin --- ---
(UL94V-0)
Power supply wires --- UL1007 AWG20 ---
*Only plug

Connector Pinout Diagram (from Mating Side)

Item No. of poles 4 poles

1
4
Male (plug) contacts
2
3
DC type
2

Female (socket) contacts

1 3
4

Connection Combinations
Smartclick Plug Connectors M12 Plug Connectors
OMRON model No. XS5H, XS5G, XS5W (plug side), XS2H, XS2G, XS2W (plug side),
XS5R (plug side), XS5M XS2R (plug side), XS2M
Smartclick Socket XS5F, XS5C, XS5W (socket side),
 ❍
Connectors XS5R (socket side), XS5P
M12 Socket XS2F, XS2C, XS2W (socket side),
❍ ❍
Connectors XS2R (socket side), XS2P
 : Connected by twisting.
❍ : Connected by screwing.
is a registered trademark of the OMRON Corporation.
Note: The XS@M and XS@P cannot mate with each other.

33
 XS5

XS5W Connectors Connected to Cable, Socket and Plug on Cable Ends

● Fire-retardant, Robot cable XS5W-D42@-@81-F
● Oil-resistant Polyurethane Cable XS5W-D42@-@81-P
● Spatter-resistant Cable XS5W-D421-@81-SA
Dimensions (Unit: mm)

Straight/straight
M12×1

14.9 dia. 14.9 dia.

40.7 44.7
L (Cable length)

Angled/angled
14.9 dia.
14.9 dia. M12×1

28.3 32.3
Wiring Diagram for 4 Cores
Pin No. Cable color of
core sheath
L (Cable length)
1 1 Brown
2 2 White
Straight/angled 14.9 dia.
3
4
3
4
Blue
Black
M12×1

32.3

14.9 dia.

40.7
L (Cable length)

Angled/straight
14.9 dia.

M12×1
28.3

14.9 dia.

44.7
L (Cable length)

Note: Oil-resistant Polyurethane Cables (XS5W-D42@-@81-P) and Spatter-resistant Cable (XS5W-D421-@81-SA) have black covers.
Fire-retardant, Robot cable (XS5W-D42@-@81-F) have warm gray covers.

34
 XS5
Model Number Legend

XS5W-D42@-@81-@@ Use this model number legend to identify products

from their model number. When ordering, use a mod-
el number from the table in Ordering Information.
1 2 3 4 5 6 7 8 9

1. Type 6. Cable Length

W: Connectors connected to cable, socket and plug C: 1 m D: 2 m E: 3 m
on cable ends G: 5 m J: 10m
2. Mating Section Form 7. Connections
D: DC 8: A Brown, B White, C Blue, D Black (Numbers
3. Connector Poles inside circles are terminal numbers)
4: 4 poles 8. Connectors on One End/Both Ends
4. Contact Plating 1: Both ends
2: 0.4-μm gold plating 9. Cable Specifications
5. Cable Connection Direction F: Fire-retardant, Robot cable
1: Straight/straight P: Oil-resistant Polyurethane Cable
2: Angled/angled SA: Spatter-resistant Cable
3: Straight (Socket)/angled (Plug)
4: Angled (Socket)/straight (Plug)

Ordering Information
Cable Cable outer Straight/straight Angled/angled Minimum
Cable specifications UL
length L (m) diameter (mm) Model order
1 XS5W-D421-C81-F --- 10
2 XS5W-D421-D81-F XS5W-D422-D81-F
Fire-retardant, Robot
3 XS5W-D421-E81-F --- 5 Yes
cable
5 XS5W-D421-G81-F XS5W-D422-G81-F
6
10 XS5W-D421-J81-F --- 1
2 XS5W-D421-D81-P ---
Oil-resistant Polyure- 5
5 XS5W-D421-G81-P --- ---
thane Cable
10 XS5W-D421-J81-P --- 1
Spatter-resistant 2 XS5W-D421-D81-SA ---
6.6 5 ---
Cable 5 XS5W-D421-G81-SA ---

Straight (Socket)/ Angled (Socket)/

Cable Cable outer angled (Plug) straight (Plug) Minimum
Cable specifications UL
length L (m) diameter (mm) order
Model
Fire-retardant, Robot 2 XS5W-D423-D81-F XS5W-D424-D81-F
6 5 Yes
cable 5 XS5W-D423-G81-F XS5W-D424-G81-F

35
 XS5

XS5F Connector Connected to Cable, Socket on One Cable End

● Fire-retardant, Robot cable XS5F-D42@-@80-F
● Oil-resistant Polyurethane Cable XS5F-D42@-@80-P
● Spatter-resistant Cable XS5F-D421-@80-SA
Dimensions (Unit: mm)

Straight
L (Cable length)
40.7

14.9 dia.
Wiring Diagram for 4 Cores
Pin No. Cable color of
M12 × 1 30 5 core sheath
50
1 Brown
2 White
3 Blue
Angled 4 Black
L (Cable length)
25.3

28.3 30 5
M12×1
50

14.9 dia.

Note: Oil-resistant Polyurethane Cables (XS5F-D42@-@80-P) and Spatter-resistant Cable (XS5F-D421-@80-SA) have black covers. Fire-
retardant, Robot cable (XS5F-D42@-@80-F) have warm gray covers.

Model Number Legend

XS5F-D42@-@80-@@ Use this model number legend to identify products

from their model number. When ordering, use a mod-
el number from the table in Ordering Information.
1 2 3 4 5 6 7 8 9

1. Type 5. Cable Connection Direction 8. Connectors on One End/Both Ends

F: Connector connected to cable, 1: Straight 0: One end
socket on one cable end 2: Angled
9. Cable Specification
2. Mating Section Form 6. Cable Length F: Fire-retardant, Robot cable
D: DC C: 1 m D: 2 m E: 3 m P: Oil-resistant Polyurethane Cable
G: 5 m J: 10 m SA: Spatter-resistant Cable
3. Connector Poles
4: 4 poles 7. Connections
8: A Brown, B White, C Blue,
4. Contact Plating D Black (Numbers inside circles are
2: 0.4-μm gold plating terminal numbers.)

Ordering Information
Cable outer Straight Connectors Angled Connectors Minimum
Cable specifications Cable length L (m) UL
diameter (mm) Model order
1 XS5F-D421-C80-F XS5F-D422-C80-F 10
2 XS5F-D421-D80-F XS5F-D422-D80-F
Fire-retardant, Robot cable 3 XS5F-D421-E80-F XS5F-D422-E80-F 5 Yes
5 XS5F-D421-G80-F XS5F-D422-G80-F
6
10 XS5F-D421-J80-F XS5F-D422-J80-F 1
2 XS5F-D421-D80-P XS5F-D422-D80-P
Oil-resistant 5
5 XS5F-D421-G80-P XS5F-D422-G80-P ---
Polyurethane Cable
10 XS5F-D421-J80-P XS5F-D422-J80-P 1
Spatter-resistant 2 XS5F-D421-D80-SA ---
6.6 5 ---
Cable 5 XS5F-D421-G80-SA ---

36
 XS5

XS5H Connector Connected to Cable, Plug on One Cable End

● Fire-retardant, Robot cable XS5H-D42@-@80-F
● Oil-resistant Polyurethane Cable XS5H-D42@-@80-P
● Spatter-resistant Cable XS5H-D421-@80-SA
Dimensions (Unit: mm)

Straight L (Cable length)

44.7

14.9 dia. Wiring Diagram for 4 Cores

30 5 Pin No. Cable color of

M12×1 core sheath
50
1 Brown
2 White
Angled L (Cable length) 3 Blue
4 Black
25.3

32.3
30 5
50

M12×1

14.9 dia.

Note: Oil-resistant Polyurethane Cables (XS5H-D42@-@80-P) and Spatter-resistant Cable (XS5H-D421-@80-SA) have black covers. Fire-
retardant, Robot cable (XS5H-D42@-@80-F) have warm gray covers.

Model Number Legend

XS5H-D42@-@80-@@ Use this model number legend to identify products

from their model number. When ordering, use a mod-
el number from the table in Ordering Information.
1 2 3 4 5 6 7 8 9

1. Type 5. Cable Connection Direction 8. Connectors on One End/Both Ends

H: Connector connected to cable, 1: Straight 0: One end
plug on one cable end 2: Angled 9. Cable Specifications
2. Mating Section Form 6. Cable Length F: Fire-retardant, Robot cable
D: DC P: Oil-resistant Polyurethane
A: 0.3 m C: 1 m D: 2 m
3. Connector Poles G: 5 m Cable
4: 4 poles SA: Spatter-resistant Cable
7. Connections
4. Contact Plating 8: A Brown, B White, C Blue,
2: 0.4-μm gold plating D Black (Numbers inside circles
are terminal numbers)

Ordering Information
Cable outer Straight Connectors Angled Connectors Minimum
Cable specifications Cable length L (m) UL
diameter (mm) Model order
0.3 XS5H-D421-A80-F XS5H-D422-A80-F
10
1 XS5H-D421-C80-F XS5H-D422-C80-F
Fire-retardant, Robot cable Yes
2 XS5H-D421-D80-F XS5H-D422-D80-F
5
5 6 XS5H-D421-G80-F XS5H-D422-G80-F
0.3 XS5H-D421-A80-P XS5H-D422-A80-P 10
Oil-resistant
2 XS5H-D421-D80-P XS5H-D422-D80-P ---
Polyurethane Cable 5
5 XS5H-D421-G80-P XS5H-D422-G80-P
Spatter-resistant 0.3 XS5H-D421-A80-SA ---
6.6 10 ---
Cable 1 XS5H-D421-C80-SA ---

37
 XS5

XS5@ Eight-pole Connectors with Cables

Ordering Information
Cable connection No. of cable Cable length L Applicable wire
Type Cable specification Model
direction cores (m) gauge
6.3 mm dia., 2 XS5F-D821-DH0-R
Connector Connected to
AWG23 (0.25 mm2) Straight 10 5 --- XS5F-D821-GH0-R
Cable, Socket on One End
Structure: 0.08 mm/60 wires 10 XS5F-D821-JH0-R
Panel-mounting Plug --- --- --- --- AWG22 to AWG28 XS5M-D827-4

Pins and Cable Lead Colors

Pin No.
A B C D E F G H
XS5F cable lead colors
White Brown Green Yellow Gray Pink Blue Red

Ratings and Specifications Materials and Finishes

Rated current 1.5 A Contacts Brass/nickel base, 0.4-μm gold plating
Rated voltage 36 VDC Fixtures Nickel-plated zinc alloy *1
40 mΩ max.
Contact resistance
(at 20 mV DC max., 100 mA max.)
Body Nickel-plated zinc alloy *2
Insulation resistance 1,000 MΩ min. (at 500 VDC) Nuts Nickel-plated brass *2
1,000 VAC for 1 min Fixtures (lock) Stainless *2
Dielectric strength
(leakage current: 1 mA max.) Contact block PBT resin (UL94V-0), light gray
Degree of protection IP67 (IEC 60529)
Cover *1 Soft PBT resin (UL94V-0)
Insertion tolerance 50 times
Seal resin *2
Ambient operating temperature range −25 to 70°C Rubber
Ambient operating humidity range 20% to 85% O-ring*1
*1. XS5F only.
*2. XS5M only.

Dimensions (Unit: mm)

XS5F-D821-@H0-R Connector Connected to Cable, Socket on One End

L (cable length)
1 2 40.7
3
7
14.9 dia.

6 4
8 (30) (5)
5 (50)
M12×1

XS5M-D827-4 Front-locking, Panel-mounting Plug

Nut 3 5
3
(19) M16×1
Seal resin Eight, 1 dia
M12×1

(21.9) 17

Pin No. 2 20 dia. Resin filling

8 2.8
22.8

Panel Cutout

14.1+0.1
0
16.1+0.1
0 dia. 16.1+0.1
0 dia.

Panel Cutout
Panel thickness (t): 1 to 4

38
 XS5

XS5G Assembly Connector Plugs

Dimensions (Unit: mm)

XS5G-D418 (IDC Model)

Straight Connectors
66
M12 × 1 58

17.5 dia. 14.9 dia.

XS5G-D4C@ (Crimping Model)

XS5G-D42@ (Soldering Model)
Straight Connectors
M12 × 1

14.9 dia. 14.2 dia.

49.3

XS5G-D42@ (Soldering Model)

Angled Connectors
M12 × 1 37.7

14.9 dia.

23

XS5G-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 7 or 8 mm)

Straight Connectors
M12 × 1
58.7

20 dia. 14.9 dia. 16 dia.

XS5G-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 3, 4, or 6 mm)

Straight Connectors
M12 × 1
58.7

20 dia. 14.9 dia. 14 dia.

XS5G-D@S@ (Screw-on Connectors) M12 × 1 39.7

Angled Connectors

20 dia. 14.9 dia.

39.6

14 dia.

39
 XS5
Ordering Information
No. of Connection Suitable cable dia. Core conductor size Suitable sheath Straight Connectors Angled Connectors Minimum
poles method (mm) (mm2) material Model order
IDC 3 to 8 mm 0.14 to 0.75 *1 XS5G-D418 ---
6 mm (5 to 6) XS5G-D4C1 ---
0.18 to 0.3
Crimping 4 mm (4 to 5) XS5G-D4C3 ---
0.5 to 0.75 *2
3 mm (3 to 4) XS5G-D4C5 ---
6 mm (5 to 6) XS5G-D421 XS5G-D422
Soldering 4 mm (4 to 5) 0.5 max. XS5G-D423 XS5G-D424
4
3 mm (3 to 4) XS5G-D425 XS5G-D426
6 mm (5 to 6) XS5G-D4S1 XS5G-D4S2
4 mm (4 to 5) PVC, PE, PUR XS5G-D4S3 XS5G-D4S4 50
Screw-on 3 mm (3 to 4) XS5G-D4S5 XS5G-D4S6
8 mm (7 to 8) XS5G-D4S7 ---
7 mm (6 to 7) XS5G-D4S9 ---
0.18 to 0.75
6 mm (5 to 6) XS5G-D5S1 ---
4 mm (4 to 5) XS5G-D5S3 ---
5 Screw-on 3 mm (3 to 4) XS5G-D5S5 ---
8 mm (7 to 8) XS5G-D5S7 ---
7 mm (6 to 7) XS5G-D5S9 ---
*1. Minimum wire diameter: 0.08 mm, Outer diameter of wire covering: 0.7 to 2.6 mm, Material of wire covering: PVC and PE
*2. There are two types of contacts.
Note: XS5G Screw-on Plugs cannot be connected to side by side to the CN1 and CN2 connectors of XS2R or XS5R Y-Joint Sockets/Plugs.
Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.

40
 XS5

XS5U (Crimping Pin for XS5G)

Dimensions (Unit: mm)

XS5U-312@ * A special tool must be used for crimping. For details, refer to page 49.
Plug Pin
Slit Dimensions
Suitable core Dimension (mm) No. of
Model
1 dia.
C dia.
2 dia. 2.3 dia. size (mm2) A B C slits

1.5 XS5U-3121 0.18 to 0.3 22.6 6.1 0.8 1

B XS5U-3122 0.5 to 0.75 22.7 6.2 1.3 0
A

Ordering Information
Suitable core size (mm2) Model Minimum order
0.18 to 0.3 XS5U-3121
100
0.5 to 0.75 XS5U-3122
Note: Orders are accepted in multiples of the minimum order.

41
 XS5

XS5C Assembly Connector Sockets

Dimensions (Unit: mm)

XS5C-D418 (IDC Model)

Straight Connectors
62.4
M12 × 1 54.4

17.5 dia. 14.9 dia.

XS5C-D4C@ (Crimping Model)

XS5C-D42@ (Soldering Model)
Straight Connectors

M12 × 1

14.9 dia. 14.2 dia.

43.4

XS5C-D4C@ (Crimping Model)

XS5C-D42@ (Soldering Model)
Angled Connectors 31.8
M12 × 1

14.9 dia.

23

XS5C-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 7 or 8 mm)

Straight Connectors
M12 × 1 54.9

20 dia. 14.9 dia. 16 dia.

XS5C-D@S@ (Screw-on Connectors, Applicable Cable Outer Diameter: 3, 4, or 6 mm)

Straight Connectors
M12 × 1 54.9

20 dia. 14.9 dia. 14 dia.

XS5C-D@S@ (Screw-on Connectors)

Angled Connectors M12 × 1 35.9

20 dia. 14.9 dia.

39.6

14 dia.

42
 XS5
Ordering Information
No. of Connection Suitable cable dia. Core conductor size Suitable sheath Straight Connectors Angled Connectors Minimum
poles method (mm) (mm2) material Model order
IDC 3 to 8 mm 0.14 to 0.75 *1 XS5C-D418 ---
6 mm (5 to 6) XS5C-D4C1 XS5C-D4C2
0.18 to 0.3
Crimping 4 mm (4 to 5) XS5C-D4C3 XS5C-D4C4
0.5 to 0.752 *2
3 mm (3 to 4) XS5C-D4C5 XS5C-D4C6
6 mm (5 to 6) XS5C-D421 XS5C-D422
Soldering 4 mm (4 to 5) 0.5 max. XS5C-D423 XS5C-D424
4
3 mm (3 to 4) XS5C-D425 XS5C-D426
6 mm (5 to 6) XS5C-D4S1 XS5C-D4S2
4 mm (4 to 5) PVC, PE, PUR XS5C-D4S3 XS5C-D4S4 50
Screw-on 3 mm (3 to 4) XS5C-D4S5 XS5C-D4S6
8 mm (7 to 8) XS5C-D4S7 ---
7 mm (6 to 7) XS5C-D4S9 ---
0.18 to 0.75
6 mm (5 to 6) XS5C-D5S1 ---
4 mm (4 to 5) XS5C-D5S3 ---
5 Screw-on 3 mm (3 to 4) XS5C-D5S5 ---
8 mm (7 to 8) XS5C-D5S7 ---
7 mm (6 to 7) XS5C-D5S9 ---
*1. Minimum wire diameter: 0.08 mm, Outer diameter of wire covering: 0.7 to 2.6 mm, Material of wire covering: PVC and PE
*2. There are two types of contacts.
Note: Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.

43
 XS5

XS5U (Crimping Pin for XS5C)

Dimensions (Unit: mm)

XS5U-222@ * A special tool must be used for crimping. For details, refer to page 49.
Socket Pin Slit Dimensions
Suitable core Dimension (mm) No. of
Model
C dia. 2 dia. 2.3 dia. size (mm2) A B C slits

1.5 XS5U-2221 0.18 to 0.3 16.7 6.1 0.8 1

B XS5U-2222 0.5 to 0.75 16.8 6.2 1.3 0
A

Ordering Information
Suitable core size (mm2) Model Minimum order
0.18 to 0.3 XS5U-2221
100
0.5 to 0.75 XS5U-2222
Orders are accepted in multiples of the minimum order.

44
 XS5

XS5R Y-Joint Plug/Socket Connectors

Dimensions (Unit: mm)

XS5R-D426-@11-F
Connectors on Both Ends (Y-Joint Plug/Socket) Wiring Diagram

15.0 M12 × 1 Socket 45.5 1

4.6 dia. 2
CN2 CN2
3
1 2 Plug
4 4
4 3
4 3 3
35.0 18.0 1 2 2
1 1
1 2
4 3 2
CN1
CN1 8.5 M12 × 1 3
Blue marking 13.6 44.7 4
L

XS5R-D426-@10-F
Connectors on One Cable End (Y-Joint Socket) Wiring Diagram

1
15.0 M12 × 1 Socket 45.5 2
CN2
3
CN2 4.6 dia.
4 Black
1 2
Blue
4 3
White
35.0 18.0
1 Brown
2
1 2 CN1
4 3 3
CN1 8.5
13.6 5 4
Blue marking 30
L 50

XS5R-D426-@
Y-Joint Plug/Socket without Cable Wiring Diagram
XS5R-D426-1 XS5R-D426-5
27
7 4 4
15 M12 × 1 Socket 4.5 dia.
3 3
CN2 CN2
2 2
CN2
1 2 1 1
4 3 CN0 Plug 24.5
(37) 18 4
4 4 4 3
1
2 CN0
CN1 3 3 CN1 3 2
4 3 CN0
CN1 12.5 2 2 2 1
1 1 1
58.3 M12 × 1

Blue marking

Ordering Information
Cable Connector Cable length (m) Model Minimum order
0.5 XS5R-D426-B11-F
10
Connectors on both cable 1 XS5R-D426-C11-F
ends 2 XS5R-D426-D11-F
With cable
3 XS5R-D426-E11-F
5
Connector on one cable 2 XS5R-D426-D10-F
end 5 XS5R-D426-G10-F

Cable Connector Cable length (m) Model Minimum order

XS5R-D426-1
With no cable Y-Joint Plug/Socket — 10
XS5R-D426-5
Note 1. Ask your OMRON representative about other specifications.
2. XS2G/XS5G Assembled Connectors with screw connections cannot be connected to both CN1 and CN2 at the same time.

45
 XS5

XS5P Panel-mounting Sockets

Dimensions (Unit: mm)

XS5P-D426-5
Rear-locking Socket Connected to Wires Wiring
18
17
M12×1
2.8 PG9 White
Pin number Color
500 Blue
1 Brown
23 2 White
18 14 14.6 dia. 20
3 Blue
10 20 Brown
Black 4 Black
2.5 11.9
22.1 Wire Specifications
Item Specification
XS5P-D427-5
Front-locking Socket Connected to Wires Specification UL1007
18 2.8 500 17 Nominal size AWG20
M12×1 PG9 White
Blue
Number of
21
2
wires
3
21 13.9 dia. 18 Config-
1
4 Wire diameter 0.18
uration
10 20
Black Brown Standard outer
1.8
diameter
10.5 2.5
22.1

XS5P-D426-4 Rear-locking Socket with Solder Cup Pins XS5P-D526-4 Rear-locking Socket with Solder Cup Pins
2.8 PG9
17 Nut 3.5 18 4, 1.3 dia. PG9 5.5
M12×1 2.8
17 Nut 3.5 18 5, 1.3 dia.
M12×1

18 14.6 dia. 20
18 14.6 dia. 20

2.5 11.9
22.1 Resin filling 2.5 11.9
Resin filling
22.1

XS5P-D427-4 Front-locking Socket with Solder Cup Pins XS5P-D527-4 Front-locking Socket with Solder Cup Pins
2.8 2.8 5.5
18 Nut 3.5 17 4, 1.3 dia. 18 Nut 3.5 17 5, 1.3 dia.
M12×1 M12×1
PG9 PG9

20 13.9 dia. 18 20 13.9 dia. 18

10.5 2.5 10.5 2.5

Resin filling Resin filling
22.1 22.1

Panel Cutout
+0.1
15.3 0 dia.
Panel Cutout Dimension
Panel thickness = 1 to 4 mm
Note 1. The panel cutout dimension is the same for Front-locking and Rear-locking Sockets.
2. Rotational positioning is not possible for connector rotation.

Ordering Information
Type No. of poles Lock Cable length (m) Model Minimum order
Rear lock XS5P-D426-5
With cable 4 0.5 10
Front lock XS5P-D427-5

Type No. of poles Lock Applicable wires Model Minimum order

Rear lock XS5P-D426-4
4
Solder cup Front lock XS5P-D427-4
AWG20 to AWG28 50
pins Rear lock XS5P-D526-4
5
Front lock XS5P-D527-4

46
 XS5

XS5M Panel-mounting Plugs

Dimensions (Unit: mm)

XS5M-D426-5
Rear-locking Plug Connected to Wires Wiring
18 2.8 PG9 18 Pin number Color
M12×1 500 Brown
1 Brown
White
1
4
2 White
17 2
20
3
3 Blue
10 20 Blue
Black 4 Black
2.8 10
22.8 Wire Specifications
XS5M-D427-5 Item Specification
Front-locking Plug Connected to Wires Specification UL1007
18 2.8 500 18
PG9
M12×1 Brown White Nominal size AWG20

1
Number of wires 21
4
20 2
17 Configu- Wire diameter 0.18
3

Blue ration
10 20 Black Standard outer
1.8
diameter
8 2.8
22.8

XS5M-D426-4 Rear-locking Plug with Solder Cup Pins XS5M-D526-4 Rear-locking Plug with Solder Cup Pins
2.8 PG9 2.8 5.5
18 Nut 3.5 18 4, 1.3 dia. 18 Nut 3.5 18 5, 1.3 dia.
M12×1 M12×1 PG9

17 20 17 20

2.8 10 2.8 10
22.8 Resin filling 22.8 Resin filling

XS5M-D427-4 Front-locking Plug with Solder Cup Pins XS5M-D527-4 Front-locking Plug with Solder Cup Pins
2.8 2.8 5.5
Nut PG9
18 3.5 18 4, 1.3 dia. 18 Nut 3.5 18 5, 1.3 dia.
M12×1 PG9 M12×1

20 17 20 17

8 2.8 8 2.8
22.8 Resin filling 22.8 Resin filling

Panel Cutout
+0.1
15.3 0 dia.
Panel Cutout Dimension
Panel thickness = 1 to 4 mm
Note 1. The panel cutout dimension is the same for Front-locking and Rear-locking Sockets.
2. Rotational positioning is not possible for connector rotation.

Ordering Information
Type No. of poles Lock Cable length (m) Model Minimum order
Rear lock XS5M-D426-5
With cable 4 0.5 10
Front lock XS5M-D427-5

Type No. of poles Lock Applicable wires Model Minimum order

Rear lock XS5M-D426-4
4
Solder cup Front lock XS5M-D427-4
AWG20 to AWG28 50
pins Rear lock XS5M-D526-4
5
Front lock XS5M-D527-4

47
 XS5
Connector Covers
Water-resistive Covers XS2Z-11 M12 male screw
XS2Z-11

M12 × 1

XS5Z-11 XS5Z-11
M12 female screw The Water-resistive Cover ensures IP67.
When mounting the Water-resistive Cover
to a Connector, be sure to apply a torque
range between 0.39 and 0.49 N·m to
tighten the Water-resistive Cover.
XS5Z-11 is Smart click mechanism. There's
no need to keep track of locking torque.

Suitable connector
Model Minimum order Material
Model Mounting portion
XS5G/XS5H/XS5M/XS5R/XS5W/
XS2Z-11 Brass/nickel plated M12 male screw
50 XS2G/XS2H/XS2M/XS2R/XS2W
XS5Z-11 PBT XS5C/XS5F/XS5P/XS5R/XS5W/XW3D M12 female screw

Dust Covers
XS2Z-13 M12 male screw
XS2Z-13

XS2Z-15/XS2Z-14 M12 female screw The Dust Cover is for dust prevention and
XS2Z-15 XS2Z-14
does not ensure IP67 degree of protection.
When mounting the Dust Cover to a
connector, be sure to press the Dust Cover
onto the Connector until the Connector is
Pin block (female pins)
fully inserted into the Dust Cover.

Suitable connector
Model Minimum order Material
Model Mounting portion
XS5G/XS5H/XS5M/XS5R/XS5W/
XS2Z-13 M12 male screw
XS2G/XS2H/XS2M/XS2R
XS2Z-14 50 Rubber/black XS5C/XS5F/XS5P/XS5R/XS5W/ Pin block (female pins)
XS2C/XS2F/XS2P/XS2R/XS2W/
XS2Z-15 M12 female screw
XW3B/XW3D

Sputter Protective Cover M12 female screw (thread bracket)

XS2Z-31
XS2Z-31 The Sputter Protective Cover protects the
connector from weld sputter.
Make sure it covers the entire connector.

Pin block (female contact)

Model Material Applicable connector

XS5F/XS5H/XS5W/
XS2Z-31 Silicone rubber/black
XS2F/XS2H/XS2W

48
 XS5
Tools
Crimp Tool Locator Tool in open position

XY2F-0002 XY2F-0003

Tool in closed
position

ER AND
ON INSTA R
TI TO LL

O
TATE 90 I

TA
PUSH POS
°
SE TO RO

TE
AI 2

90° TO

R
1

3 TA
TE
SEL.

RO

4
NO.

IN
ST
AL

7
L 5
6

Use the Crimp Tool to crimp a cable core to the XS5U or XS2U Selector dial XY2F-0002
Crimping Pin used with the XS@C or XS@G Crimping Connector. (Set to 8.) Crimp Tool
Locator guide

Model
• The XY2F-0002 Crimp Tool is DMC's AFM8 (M22520/2-01). XY2F-0003
• Mount the XY2F-0003 Locator (sold separately) to the locator Locator XY2F-0002
guide of the Crimp Tool with a screw provided with the XY2F-0003 XY2F-0003
Locator.

Pin-block Extraction Tool

XY2F-0001
Use this tool to extract a Pin Block from the covers in order to make
wiring changes or corrections after the cover has been mounted to the
pin block for Connector Assemblies (XS@C/XS@G, soldering/
crimping).
Model
XY2F-0001

Extraction Procedure
(1) Disconnecting Components • Make sure that the pin block is outside the Tool.
• Disconnect all components on the cap side from the cover.
Tool

Pin block

Pin block Cover Rubber Cable Cap Cover

Guide
bushing clamp Cover

• Press the Tool so that the guides of the Tool are in close contact.
Then pull the pin block straight.

Guide
(2) Extracting Pin Block Pin block
• Insert the claws of the Tool into the four holes of the cover.

Holes

Extracting
direction

Precaution for Safe Use

• The pin block must not be extracted from the same Connector
more than 3 times, otherwise the proper degree of protection of the
Claws pin block or Connector will not be maintained.

49
 XS5
Assembly Procedure for XS5C/XS5G (IDC models) Connector Assemblies
(1) Preparations (Make sure they are all at hand.) (6) Processing the core wire end
• Cut the end part of each core wire with nippers. Cutting the
core wire end in the range of cut-area of figure.
Terminal number
indication surface

Contact block IDC cover Cap Boss Core wire

Cap unit

(2) Dressing the cable end

• Peel covering of a cable. Cut-area

Note: Please be careful not to cut the boss.

(7) Assembling the Contact block

approx. 40 mm
Cable • Insert the cap unit core wire end processing has completed
External diameter of in a contact block.
applicable cable
Conductor cross section • Use a mark of a housing and an arrow of a IDC cover, as
a guideline of alignment. The location of the arrow is the
3 to 8 mm 0.14 to 0.75mm2 / AWG26 to 18
side of the terminal No.1.
(3) Choose the waterproof bushing
• Choose the waterproof bushing type according to the cable
size.
<External diameter of cable: In case of 3 to 5 mm>
Use the cap unit in the delivery state.
Pink marking

Housing

* Color : Housing/ IDC cover

<External diameter of cable: In case of 5 to 8 mm> XS5C : Gray
When using, pick tab both sides of the waterproof bushing XS5G : White
with a tab and pull it out in the direction of an arrow. Note: Confirm that the color of the housing and the IDC cover is same before
insertion.

(8) Tightening up the cap

• After inserting the cap unit and tightening a screw up lightly
(Not required.)
by hand, screw up the cap by a tool of a spanner or wrench
waterproof bushing with a tab
(size 15 mm).*2
Note: When it isn't necessary to pull out bushing, do not pull a tab or pull out
bushing carelessly. Do not insert the pulled-out bushing again.

(4) Cable insertion

• Insert a cable in the cap unit.
* Insert fully until a cable doesn't
enter any more.
* It's shown by a figure in case of
cable external diameter 3 to 5
mm.
*2. When screwing up the cap by large size tool,
completion position
(5) Wiring it may cause damage.
• When a gap between a mold cover of contact block and a
• Confirm the terminal number indication*1 of a IDC
cap disappeared assembly and wire connection has
(Insulation Displacement Contact) cover, insert a core wire
completed.
in each wire guide according to the terminal number and
push in to the lowermost part of a core wire storage part.
*1. Terminal No.1: Brown
Terminal No.2: White
Terminal No.3: Blue Fixture
Terminal No.4: Black Mold cover
Core wire storage part completion position

Note 1. When the operation has completed, mark of cap comes into the
square of the indicator formed into a mold cover ( ), so also use
Note: There is a difference in a it as guideline to know to complete.
storing state depending 2. Avoid tightening a cap up beyond the completion position. It may cause
Core wire Wire guide part on core wire diameter. damage.

(9) Final checking

• When the connector has been assembled, make sure the
line insulation is as specified.

50
 XS5

Repair work procedure

Cap unit removal

• When releasing wire connection, remove the cap unit in the
opposite procedure of assembly work. [ from (8) to (7) ]
Note 1. The core wire remain connected to the IDC connection part rarely. In
that case, remove core wire end part to the vertical direction by
tweezers etc. Do not touch the IDC contact directly at that time.
2. When IDC cover was left on the housing side, remove it by pulling a
cable. In case IDC cover has been removed by holding strongly and
pulling, it may cause damage.
Cable removal
• When removing the cable from the cap unit,
pull the cable to the opposite direction of
assembly work procedure (4). When tip of
the core wire end has been pushed lightly
into the IDC cover by tweezers etc, cable
removal becomes easy.
Repair work
• When connecting the wire again, do assembly (repair work)
according to assembling procedure from (1) to (8).
Note 1. In case of repair, use a cable of the same diameter and a core wire of
the same diameter. The number of times of repair wire connection is
maximum 10 times.
2. When doing a repair, work after enough removing the foreign substance
and moisture adhering to a connector. Be careful so that the foreign
substance and moisture do not enter the wire connection part. It may
cause short-circuit etc.

51
 XS5
Assembly Procedure for XS5C/XS5G (Crimping/Soldering/Screw-on models)
Connector Assemblies
(1) Connector and Cable External Diameters (3) Wiring (Processing Cable Ends)
• Connectors for 8 ,7 ,6 , 4 , and 3 mm diameter Cables (i.e., Cables
that are 7 to 8, 6 to 7, 5 to 6, 4 to 5, and 3 to 4 mm in diameter
Soldering Connectors
respectively) are available. When assembling a Connector used
4
with a cable, make sure that the external diameter of the Connector 6
is suited to that of the cable.
• A watertight bushing for 6/7 mm diameter Cable has no stripe, that
for 8/4 mm diameter Cable has a single stripe, and that for 3 mm
diameter Cable has two stripes. 6±0.5 *A

• Strip 10 mm of the Cable sheath and 4 mm of each core.

(2) Component Insertion • Before soldering cores and solder cup pins together, solder-coat
each of them.
Crimping/Soldering Connectors • The following conditions are recommended for soldering each
Straight Connectors solder cup pin.
Watertight Cable Soldering temperature: 350±5°C
Cover bushing clamp Cap Soldering period: 3±1 s
• The length marked *A should be 6.5 mm max., otherwise the
proper degree of protection of the connector will not be maintained.
Crimping Connectors
Angled Connectors Crimping
4
10 0
−4
Ring (Angled models only) *

Cable clamp
Watertight Cap
bushing
Cover
• Strip 14 mm of the Cable sheath and 4 mm of each core.
• Make sure that each core is not damaged and its end strands are
not spread out.
* A ring is not required for Screw-on Connectors. • Mount the XY2F-0003 Locator to XY2F-0002 Crimping Tool, both
of which are sold separately, and set the selector dial of the
• As shown in the above illustration, connect the above components Crimping Tool to 8.
to the Cable with its end processed. • After mounting the crimping pins to the Locator, fully insert the
Screw-on Connectors cores to the crimping pins.
• Squeeze the handle of the Crimp Tool to press-fit the cores to the
Confirm that you have all of the required parts. crimping pins.
(Squeeze the handle firmly until the handle automatically returns to
Cover Cable clamp
Watertight
the release position.)
bushing Cap
Wiring
Pin clamp
( *2
) Press

Ring *1 Watertight bushing

Cable clamp
Cap
Cover 1 to 1.5

• After press-fitting the cores to the pins, insert the pins into the pin
Insulation caps and insulation tubes are included with clamp as shown in the illustration. Then make sure that the lead
five-pole Connectors (XS2C-D5S@ and XS2G-D5S@). colors correspond to the pin clamp numbers that are identical to
the connector pin numbers.
*1. Rings are not required with 7-mm and 8-mm cables.
*2. Insert the waterproof bushing for 7-mm and 8-mm
cables in the direction shown in the diagram.

52
 XS5

Insertion • Bend the cable as shown below, attached the enclosed insulation
cap, and then strip the other cores.
Pin Block Pin Clamp
Key groove Key groove

XS5C use XS5G use

Key

6±0.5 Insulation cap

• Tentatively insert the pins to the pin block holes so that the key on • Connect the cores to pins 1 to 4.
the pin block will coincide with the key groove on the pin clamp.
Then insert the cable along with the pin clamp. Connecting Shielded Cables to Five-pole Connectors
• Place the insulation tub on the drain line of the shield and connect
Screw-on Connectors it to the terminal.
Cable End Processing • Tighten the screw and then check visually to see if there is
• Four-pole Connectors insulation between the cores.
Drain line
8
Insulation tube
12

12±0.5 • Connect the cores to pins 1 to 4.

• Loosen the screws on pins 1 to 4 and insert the cores according to * When tightening the screws, use the dedicated XW4Z-00B
Screwdriver that matches with the screw-slot dimensions.
the pin numbers.

XW4Z-00B
• Use the dedicated Screwdriver (XW4Z-00B)* and tighten the Screwdriver
screws securely so that the cores do not pull out (tightening torque:
0.15 to 0.2 N·m).
(4) Inserting Pin Block
• Five-pole Connectors
• Strip the cable sheath for a total of 15 mm and strip the core Pin Block Cover
(Soldering Model) (Straight Model)
covering for 8 mm for the core to connect to pin 5.
Lock spring
O-ring
8
12 Conductors for
pins 1 to 4

Conductors for Polarity key Positioning key

8 7 (triangle mark) Triangle mark
pin 5

(Crimping Model) (Angled Model)

• Connect the core to pin 5 (in the center) first.
• Insert the core from the side of the hold with the tab and tighten the
screw securely (tightening torque: Pins1 to 4: 0.15 to 0.2 N·m,
Pins5: 0.03 to 0.05 N·m), and then cut off the excess wire with wire
cutters.
• Mount the cover to the pin block so that the triangle mark on the pin
Screw
block will coincide with the triangle mark on the cover.
Screw
Dedicated • If the cover is used for an Angled model, the relationship between
screwdriver the position of the polarity key on the engaged side and cable
Dedicated
connection direction will be determined by the direction in which
screwdriver the positioning key is inserted into the cover, which can be rotated
Tab
by 90°.
• Fully insert the positioning key until the positioning key is hidden by
the casing.

53
 XS5
Connecting the XS5
1. Connecting the XS5 Plug and Socket
Pin Block
(Screw-on Connectors) • Align the projection on the plug cover with the polarity key on the
socket, then insert the plug all the way in.
Triangle mark Cover

Polarity key Protrusion on

cover aligns with
polarity key.
Cover lock Pin block

• Align the triangular marks on the pin block and cover and insert the
pin block into the cover. • Hold the knurled socket grip, then insert the projection on the plug
• Press them together firmly (0.39 to 0.49 N·m) until the pin block into the groove of the socket.
does not come out of the cover.

(5) Mounting Cap

• After mounting the cover to the pin block and the cover snaps into
place, tighten the cap securely by hand within a torque of 0.39 and
0.49 N·m.
Note: If the cap is not tighten securely enough, the degree of
protection (IP67) may not be maintained or vibration may • Turn the knurled grips of the socket clockwise approximately 45
cause the cap to become loose. Do not tighten the cap with degrees in respect to the plug. A click will indicate that the
pliers or similar tools; they may damage the cap. Connectors are locked. The locking condition can also be
confirmed by the alignment marks on the plug and socket.

A Cap
Alignment marks
• After fully tightening the cap, length A should be approximately one
of the following according to the cable external diameter and the
Connector model. 2. Connecting the XS5 and XS2
• Align the projection on the plug cover with the polarity key on the
Cable external diameter (mm)
Connector socket, then insert the plug all the way in.
6 mm 5 mm 4 mm 3 mm • In the same way as when connecting two XS2 Connectors, screw
For 6-mm-dia. cable 1 0 --- --- the knurled grip in the clockwise direction.
For 4-mm-dia. cable --- 2 1 --- • Use your fingers to tighten the Connectors sufficiently.
For 3-mm-dia. cable --- --- 2 1

(6) After Assembly

• Confirm the insulation between cores after completing assembly.

Recommended Cables
When connecting a commercially available cable to a connector
assembly, use a cable with an outside diameter of 3 to 6 mm and core
sizes of 0.18 to 0.75 mm2 for crimping connectors and 0.5 mm2
maximum for soldering connectors.

Connector Arrangement
For safety, when constructing a connection system between a Sensor
and panel with a connector, make sure that the connector plug is on
the Sensor side and the connector socket is on the panel side (i.e.,
the female pins are located on the power-supply side).
Sensor Side Connecting Cable Panel Side
(Power-supply Side)

(Plug) (Socket) (Plug) (Socket)

54
 XS5
Safety Precautions General Precautions
• Do not pull excessively on the Connectors or cables. Do not install
Precautions for Correct Use
the Connectors or cables in any way that would place a load
Do not use the Connectors in an atmosphere or environment that directly on the mating section or cable connections. Doing so can
exceeds the specifications. damage the Connectors or break the wires inside the cables.
Connector Connection and Disconnection • Install the Connectors and cables where they will not be stepped
• When connecting or disconnecting Connectors, be sure to hold the on to prevent the wires inside the cables from being broken and to
Connectors by hand. prevent the Connectors from being damaged. If the Connectors or
• Do not hold the cable when disconnecting Connectors. cables must be installed where they might be stepped on, protect
• When mating Connectors, be sure to insert the plug all the way to them with covers.
the back of the socket before attempting to lock the Connectors. • Refer to the specifications for your cables before bending the
• Do not use tools of any sort to mate the Connectors. Always use cables and do not bend them past their minimum bending radius.
your hands. Pliers or other tools may damage the Connectors. • If sensors or switches are not attached during installation, protect
• When mating the Connectors to XS2 or other M12 Connectors, the mating surface of the Connector with a XS5Z-11 Waterproof
tighten the lock by hand to a torque of 0.39 to 0.49 N⋅m. Cover of XS2Z-14/15 Dust Cover.

Wiring Setup
• Always confirm wiring diagrams before wiring sensors, limit
• Do not make any cable bends near the base of the Unit.
switches, or other devices.
• Any bends made must have a minimum radius of 40 mm.
• Lay the cables so that external force is not applied to the
Connectors. Otherwise, the degree of protection (IP67) may not be
achieved.

Degree of Protection
• The degree of protection of Connectors (IP67) is not for a fully
watertight structure. Do not the Connectors underwater.
• Do not step on or place any objects on the Connectors. Doing so
may damage the Connectors.

55
 XS5
XS5-compatible Products
Photoelectric Sensors
E3ZM-C Oil-resistant, Robust, Compact Photoelectric Sensor (Stainless Housing and Built-in Amplifier)
Orange light Red light Infrared light
Model
Sensing method Appearance Sensing distance
NPN output PNP output
E3ZM-CT61-M1TJ E3ZM-CT81-M1TJ
15 m
0.3M 0.3M
Through-beam
E3ZM-CT62B-M1TJ E3ZM-CT82B-M1TJ
20 m
0.3M 0.3M

4 m [100 mm]* E3ZM-CR61-M1TJ E3ZM-CR81-M1TJ

Retro-reflective
(Using E39-R1S) 0.3M 0.3M

E3ZM-CD62-M1TJ E3ZM-CD82-M1TJ
Diffuse reflective 1m
0.3M 0.3M

E3ZM-CL61H-M1TJ E3ZM-CL81H-M1TJ
10 to 100 mm
0.3M 0.3M
E3ZM-CL62H-M1TJ E3ZM-CL82H-M1TJ
BGS reflective 10 to 150 mm
0.3M 0.3M
E3ZM-CL64H-M1TJ E3ZM-CL84H-M1TJ
10 to 200 mm
0.3M 0.3M
*Separate the Sensor and Reflector by at least the distance given in parentheses.

E3Z Compact Photoelectric Sensor with Built-in Amplifier

Model
Sensing method Appearance Sensing distance
NPN output PNP output

E3Z-T61-M1TJ E3Z-T81-M1TJ
Through-beam 15 m
0.3M 0.3M

Retro-reflective *2
4m E3Z-R61-M1TJ E3Z-R81-M1TJ
with MSR func-
*1 [100 mm] 0.3M 0.3M
tion
E3Z-D81-M1TJ
5 to 100 mm (wide view) ---
0.3M
Diffuse reflective
E3Z-D62-M1TJ E3Z-D82-M1TJ
1m
0.3M 0.3M

Narrow-beam E3Z-L61-M1TJ E3Z-L81-M1TJ

reflective
90±30 mm
0.3M 0.3M
*1 The Reflector is sold separately. Select the Reflector model most suited to the application.
*2 The sensing distance specified is possible when the E39-R1S is used. Values in parentheses indicate the minimum required distance between
the Sensor and Reflector.

56
 XS5

E3T "Mini" Photoelectric Sensor with Built-in Amplifier Infrared light

Sensing Sensing Operating Model

Appearance
method distance mode NPN output PNP output
E3T-ST11-M1TJ E3T-ST13-M1TJ
1m Light-ON
0.3M 0.3M
Side-view E3T-ST12-M1TJ E3T-ST14-M1TJ
Dark-ON
0.3M 0.3M
E3T-ST21-M1TJ E3T-ST23-M1TJ
Light-ON
0.3M 0.3M
300 mm
E3T-ST22-M1TJ E3T-ST24-M1TJ
Dark-ON
Through- 0.3M 0.3M
beam E3T-FT11-M1TJ E3T-FT13-M1TJ
Light-ON
0.3M 0.3M
Flat 500 mm
E3T-FT12-M1TJ E3T-FT14-M1TJ
Dark-ON
0.3M 0.3M
E3T-FT21-M1TJ E3T-FT23-M1TJ
Light-ON
0.3M 0.3M
300 mm
E3T-FT22-M1TJ E3T-FT24-M1TJ
Dark-ON
0.3M 0.3M
Side-view *2
E3T-SR41-M1TJ E3T-SR43-M1TJ
Light-ON
0.3M*2 0.3M*2
Retro-reflec-
tive
E3T-SR42-M1TJ E3T-SR44-M1TJ
Using E39-R37-CA Dark-ON
100mm 10mm *1 0.3M*2 0.3M*2

Flat E3T-FD11-M1TJ E3T-FD13-M1TJ

Light-ON
0.3M 0.3M
Diffuse
reflective
5 to 30 mm
E3T-FD12-M1TJ E3T-FD14-M1TJ
Dark-ON
0.3M 0.3M

E3T-SL11-M1TJ E3T-SL13-M1TJ
Light-ON
0.3M 0.3M
Side-view 5 to 15 mm
E3T-SL12-M1TJ E3T-SL14-M1TJ
Dark-ON
Convergent 0.3M 0.3M
reflective E3T-SL21-M1TJ E3T-SL23-M1TJ
Light-ON
0.3M 0.3M
5 to 30 mm
E3T-SL22-M1TJ E3T-SL24-M1TJ
Dark-ON
0.3M 0.3M
E3T-FL11-M1TJ E3T-FL13-M1TJ
Light-ON
0.3M 0.3M
Flat 1 to 15 mm
E3T-FL12-M1TJ E3T-FL14-M1TJ
Dark-ON
BGS 0.3M 0.3M
reflective E3T-FL21-M1TJ E3T-FL23-M1TJ
Light-ON
0.3M 0.3M
1 to 30 mm
E3T-FL22-M1TJ E3T-FL24-M1TJ
Dark-ON
0.3M 0.3M
*1.Values in parentheses indicate the minimum required distance between the Sensor and Reflector.
*2.Models are available with the E39-R37-CA Reflector included.
Models with E39-R37-CA Reflector: E3T-SR4@-S

57
 XS5

Proximity Sensors
Standard Models (Completely stainless-steel housing)
Connection method Appearance Sensing distance Output Operation mode Model

Shielded M8 2mm E2EF-X2D1-M1TGJ 0.3M

Pre-wired Smartclick M12 3mm E2EF-X3D1-M1TGJ 0.3M
DC 2-Wire
Connector Models NO
(M12) M18 7mm (polarity) E2EF-X7D1-M1TGJ 0.3M
M30 12mm E2EF-X12D1-M1TGJ 0.3M

Spatter-resistant Models (Completely stainless-steel housing with fluororesin coating)

Connection method Appearance Sensing distance Output Operation mode Model

Shielded M8 2mm E2EF-QX2D1-M1TGJ 0.3M

Pre-wired Smartclick M12 3mm E2EF-QX3D1-M1TGJ 0.3M
DC 2-Wire
Connector Models NO
(M12) M18 7mm (polarity) E2EF-QX7D1-M1TGJ 0.3M
M30 12mm E2EF-QX12D1-M1TGJ 0.3M
Note: Vinyl chloride is used for the cable material, and separate protection is required.

Proximity Sensors with Oil-resistant Cables (PUR Cables)

Appearance Sensing distance Output configuration Operating mode Model
M8 2 mm E2E-X2D1-M1TGJ-U 0.3M
M12 3 mm 2-Wire DC E2E-X3D1-M1TGJ-U 0.3M
Polarity NO
M18 7 mm 1,4 Pin Specifications E2E-X7D1-M1TGJ-U 0.3M
Shielded M30 10 mm E2E-X10D1-M1TGJ-U 0.3M
M8 2 mm E2E-X2D2-M1TGJ-U 0.3M
M12 3 mm 2-Wire DC E2E-X3D2-M1TGJ-U 0.3M
Polarity NC
M18 7 mm 1,2 Pin Specifications E2E-X7D2-M1TGJ-U 0.3M
M30 10 mm E2E-X10D2-M1TGJ-U 0.3M

Standard Proximity Sensor (PVC Cable)

Appearance Sensing distance Output configuration Operating mode Model
M8 2 mm E2E-X2D1-M1TGJ 0.3M
Shielded M12 3 mm 2-Wire DC E2E-X3D1-M1TGJ 0.3M
Polarity NO
M18 7 mm 1,4 Pin Specifications E2E-X7D1-M1TGJ 0.3M
M30 10 mm E2E-X10D1-M1TGJ 0.3M
M12 8 mm E2E-X8MD1-M1TGJ 0.3M
Non-shielded 2-Wire DC
M18 14 mm Polarity NO E2E-X14MD1-M1TGJ 0.3M
1,4 Pin Specifications
M30 20 mm E2E-X20MD1-M1TGJ 0.3M

Spatter-Immune Proximity Sensor (Fire-retardant PVC Cable)

Appearance Sensing distance Output configuration Operating mode Model
M12 3 mm E2EQ-X3D1-M1TGJ 0.3M
2-Wire DC
M18 7 mm Polarity NO E2EQ-X7D1-M1TGJ 0.3M
Shielded 1,4 Pin Specifications
M30 10 mm E2EQ-X10D1-M1TGJ 0.3M
M12 4 mm E2EQ-X4X1-M1TJ 0.3M
2-Wire DC
M18 8 mm Polarity NO E2EQ-X8X1-M1TJ 0.3M
3,4 Pin Specifications
M30 15 mm E2EQ-X15X1-M1TJ 0.3M

58
 XS5

Proximity Sensor with All-stainless Housing (Fire-retardant PVC Cable)

Appearance Sensing distance Output configuration Operating mode Model
M8 1.5 mm E2FM-X1R5D1-M1TGJ 0.3M
Shielded M12 2 mm 2-Wire DC E2FM-X2D1-M1TGJ 0.3M
Polarity NO
M18 5 mm 1,4 Pin Specifications E2FM-X5D1-M1TGJ 0.3M
M30 10 mm E2FM-X10D1-M1TGJ 0.3M

Chip-Immune Inductive Proximity Sensor (PVC Cable)

Appearance Sensing distance Output configuration Operating mode Model
M12 2 mm E2EZ-X2D1-M1TGJ 0.3M
2-Wire DC
M18 4 mm Polarity NO E2EZ-X4D1-M1TGJ 0.3M
Shielded 1,4 Pin Specifications
M30 8 mm E2EZ-X8D1-M1TGJ 0.3M
M12 2 mm E2EZ-X2D1-M1TJ 0.3M
2-Wire DC
M18 4 mm Polarity NO E2EZ-X4D1-M1TJ 0.3M
3,4 Pin Specifications
M30 8 mm E2EZ-X8D1-M1TJ 0.3M

All-metal, Long-distance Proximity Sensors

Appearance Sensing distance Output configuration Operating mode Model
M12 4 mm E2V-X4B1-M1TJ 0.3M
3-Wire DC
M18 8 mm PNP NO E2V-X8B1-M1TJ 0.3M
Shielded 1, 4, 3 Pin Specifications
M30 15 mm E2V-X15B1-M1TJ 0.3M
M12 4 mm E2V-X4C1-M1TJ 0.3M
3-Wire DC
M18 8 mm NPN NO E2V-X8C1-M1TJ 0.3M
1, 4, 3 Pin Specifications
M30 15 mm E2V-X15C1-M1TJ 0.3M

Cable Amplifier Proximity Sensor

Appearance Sensing distance Output configuration Operating mode Model
3 dia. 0.8 mm E2EC-CR8D1-M1TGJ 0.5M
2-Wire DC
5.4 dia. 1.5 mm Polarity NO E2EC-C1R5D1-M1TGJ 0.5M
Shielded 1,4 Pin Specifications
8 dia. 3 mm E2EC-C3D1-M1TGJ 0.5M
2-Wire DC
8 dia. 2 mm No polarity NO E2EC-QC2D1-M1TGJ-T 0.3M
3, 4 Pin Specifications

59
 XS5

Limit Switches with Prewired DC Connectors

General-Purpose Limit Switches
Operating characteristics With LED operation indicator
Cable Pin con-
Actuator Pretravel Total travel length nections Model
(PT) (TT)
Roller lever Standard
NO: 3 4
models 90° 0.3m WLCA2-LD-DTGJ-N
15° NC: 1 2
NO: 3 4
0.3m WLG2-LD-DTGJ-N
NC: 1 2
NO: 3 4
0.3m WLG2-LD-DTK1EJ-N
High NC: 2
sensitivity 90°
10° 0.3m NO: 3 4 WLG2-LD-M1TJ-N

0.3m NO: 1 4 WLG2-LD-M1TGJ-N

0.3m NC: 2 3 WLG2-LD-M1TJB-N

Models with Spatter Countermeasures

Operating characteristics With LED operation indicator
Cable Pin con-
Actuator Pretravel Total travel length nections Model
(PT) (TT)
With Allen Standard
head bolt NO: 3 4
models 90° 0.3m WLCA2-LDS-DTGJS-N
15° NC: 1 2
Roller lever
High
NO: 3 4
sensitivity 90° 0.3m WLG2-LDS-DTGJS-N
10° NC: 1 2
With Dou-
ble nut
High
NO: 3 4
sensitivity 90° 0.3m WLG2-LDAS-DTGJS-N
10° NC: 1 2

With Allen
head bolt
providing
hexagonal
High
head NO: 3 4
sensitivity 90° 0.3m WLG2-LDFS-DTGJS-N
10° NC: 1 2

Operation Indicator Lighting Specifications and Internal Wiring

Wiring Operation indicator lighting Operation indicator
specification code specification connection pins
DTGJ
Lit when not operating
DTGJS 3 4
(connected to NO side)
DTK1EJ
Lit when not operating
M1TJ 3 4
(connected to NO side)
Lit when not operating
M1TGJ 1 4
(connected to NO side)
Lit when operating
M1TJB 2 3
(connected to NC side)
*Certified standards : UL, CCC,and EN.

60
 Connector Terminal Boxes

XW3D
Simple Wiring of Sensor Actuators
• Greatly reduce wiring in combination with the Smartclick XS5.
• Insert the connector and turn 1/8 of a turn to lock the connectors.
• Higher rated current to enable output applications.
• Use previous M12 screw connectors.

Refer to Safety Precautions on page 64.

Specifications Materials and Finish

Rated current 4 A/port, 12 A/Box (power line) Item Materials/finish
Rated voltage 10 to 30 VDC Contacts Brass/nickel base, 0.4-μm gold-plating
Contact resistance 40 mΩ max. Fixtures Nickel-plated zinc alloy
(connector) (20 mV max., 100 mA max.) Case PBT resin (UL94V-O), light gray
Insulation resistance 100 MΩ min. (at 500 VDC) Bushing Rubber
Dielectric strength 500 VAC for 1 min O-ring Rubber
(connector) (leakage current: 1 mA max.)
PCB Glass epoxy board
Degree of protection IP67 (IEC60529)
Sealing resin Urethane resin (UL94V-0)
Insertion tolerance 50 times.
UL AWM2464
Lock strength Pulling: 100 N/15 s, Twisting: 1 N·m/15 s Cable Signal lines: AWG22
Cable holding Power and ground lines: AWG18
100 N/15 s
strength
Lock operating force 0.1 to 0.25 N·m
Ambient temperature
Operating: −25 to 70°C
range

Connection Combinations

Twist-and-Click M12 Plug

Plug Connectors Connectors
OMRON model no. XS5H, XS5G, XS2H, XS2G,
XS5W (plug end), XS2W (plug end),
XS5R (plug end) XS2R (plug end)
: Connected by .
Connector Terminal Box XW3D c
c: Connected by screwing.

is a registered trademark of the OMRON Corporation.

61
 XW3D
Ordering Information
Sensor type and wiring 3-wire DC NPN/2-wire DC 3 - 4 2-wire DC 1 - 4 /without polarity 3 - 4 3-wire DC PNP/2-wire DC 1 - 4

Actuator wiring Actuator wiring 1 - 4 — Actuator wiring 3 - 4

No. of ports No. of I/O Model

4 4 XW3D-P455-G11 XW3D-P452-G11 XW3D-P453-G11
8 8 XW3D-P855-G11 XW3D-P852-G11 XW3D-P853-G11
4 8 XW3D-P458-G11 — XW3D-P457-G11
Note 1. " 1 - 4 " and " 3 - 4 " are the connector pin numbers that are wired.
2. All cables are 5 m long.

Waterproof Cover (Sold Separately)

Appearance Model No. per box Material

XS5Z-11 50 PBT

XS2Z-22 50 Brass with Ni plating

Note 1. The XW3D/XW3B/XW3A comes with a dust cover. If IP67 degree of protection is required, use the XS5Z-11 or XS2Z-22 (sold separately).
2. The XS2Z-22 connection is threaded.

Dimensions (Unit: mm)

XW3D-P45@-G11 Power indicator (green LED)

(Model with Four Ports) Operation indicator (red LED)

73
4.5

4.5 dia.

33
54 27

5000 100 10
4.5 dia. 120

9
9 27 30.5
82

Indication of internal wiring

6.5
20
13.5 9 9

XW3D-P85@-G11 Power indicator (green LED)

(Model with Eight Ports) Operation indicator (red LED)

73
4.5 dia. 9 dia. 4.5

4.5 dia.

33
54 27

5000 100 10
120

9
27 27 27 30.5
127

Indication of internal wiring

6.5
20
13.5 9 9

62
 XW3D

XW3D-P457-G11
Power indicator (green LED)
(Model with Four Ports and Eight I/O)
Operation indicator (red LED)

73
4.5

4.5 dia.

33
54 27

5000 100 10
120
4.5 dia.

9
9 27 30.5
82

Indication of internal wiring

6.5
20
13.5 9 9

Wiring Diagrams
Models with One I/O and One Port
XW3D-P@55-@11 XW3D-P@52-@11 XW3D-P@53-@11
3-WIRE 2-WIRE 3-WIRE
for 3-wire NPN, NPN for 2-wire DC for 3-wire PNP, PNP
2-wire DC (without polarity 3 - 4 ), (polarity 1 - 4 , without polarity 3 - 4 ) 2-wire DC (with polarity 1 - 4 ),
and Actuator ( 1 - 4 ) Note: Cannot be used with Proximity Sensors of and Actuator ( 3 - 4 )
conventional connector pin with polarity 3 - 4 .

Positive Negative Positive Negative Positive Negative

power supply power supply Ground power supply power supply Ground power supply power supply Ground
(Brown) (Blue) (Green/Yellow) (Brown) (Blue) (Green/Yellow) (Brown) (Blue) (Green/Yellow)
Connector Connector Connector
Power indicator pin number Power indicator Power indicator pin number
(green LED) pin number
(green LED) (green LED)

1 Signal 1 1 1 1
Signal 1 1 (White) Signal 1 1
4 5 2 4 5 2 4 5 2
(White) (White)
3 Lead color 3 3
Operation indicator (red LED)
Lead color Operation indicator (red LED) Lead color Operation indicator (red LED)
1 Signal 2 2 1 1

Signal 2 2 4 5 2
(Green) 4 5 2 Signal 2 2 4 5 2
(Green) (Green)
3 3 3

1 Signal 3 3 1 1

Signal 3 3 4 5 2 (Yellow) 4 5 2 Signal 3 3 4 5 2

(Yellow) 3 3 (Yellow) 3

1 Signal 4 4 1 1

Signal 4 4 4 5 2 (Gray) 4 5 2 Signal 4 4 4 5 2

(Gray) 3 3 (Gray) 3

1 Signal 5 5 1 1

Signal 5 5 4 5 2 (Pink) 4 5 2 Signal 5 5 4 5 2

(Pink) 3 3 (Pink) 3

1 Signal 6 6 1 1

Signal 6 6 4 5 2 (Red) 4 5 2 Signal 6 6 4 5 2

(Red) 3 3 (Red) 3

1 Signal 7 7 1 1

Signal 7 7 4 5 2 (Black) 4 5 2 Signal 7 7 4 5 2

(Black) 3 3 (Black) 3

1 Signal 8 8 1 1

Signal 8 8 4 5 2 (Purple) 4 5 2 Signal 8 8 4 5 2

(Purple) 3 3 (Purple) 3

Note 1. The above wiring diagrams are for eight-port use.

2. Figures in parentheses indicate lead colors.
3. The expression "white/red" means white and red stripes.
4. Here, " 1 - 4 " and " 3 - 4 " are pin numbers.
5. Contact numbers 5 through 8 in the above diagrams do not exist on Terminal Boxes with four ports. The lead colors for signals 1 through 4, power supply, and
ground are the same.

63
 XW3D

Models with Two I/O and One Port

XW3D-P458-G11 XW3D-P457-G11
for 3-wire NPN and for 3-wire PNP and
Actuator ( 1 - 4 or 1 - 2 ) Actuator ( 3 - 4 or 3 - 2 )
3-WIRE 3-WIRE
Positive Negative NPN (2) Positive Negative PNP (2)
power supply power supply Ground power supply power supply Ground
(Brown) (Blue) (Green/Yellow) (Brown) (Blue) (Green/Yellow)

Connector Connector
pin number pin number

Signal 1B 1 Signal 1B 1
(Pink) 1
(Pink) 1

Signal 1A 1 4 5 2 Signal 1A 1 4 5 2
(White) 3 (White) 3

Lead color Lead color

Signal 2B 2 Signal 2B 2
(Red) 1 (Red) 1

Signal 2A 2 4 5 2 Signal 2A 2 4 5 2
(Green) 3 (Green) 3

Signal 3B 3 Signal 3B 3
(Black) 1 (Black) 1

Signal 3A 3 4 5 2 Signal 3A 3 4 5 2
(Yellow) 3 (Yellow) 3

Signal 4B 4 Signal 4B 4
(Purple) 1 (Purple) 1

Signal 4A 4 4 5 2 Signal 4A 4 4 5 2
(Gray) 3 (Gray) 3

Note: Colors given in the connection diagram are lead colors.

Mounting Dimensions (Unit: mm)

Three, M4 or 4.5 dia.

33±0.1

73±0.1
Note: The mounting dimensions are the same regardless of the number of ports.

Safety Precautions

Precautions for Correct Use

Do not use the Connectors in an atmosphere or environment ● Cable Lead Polarity
that exceeds the specifications. • Connect the cables leads using the correct polarity (Blue:
● Connector Connection and Disconnection Negative power supply, Brown: Positive power supply).
• Mate the connectors according to the procedure. • If the polarity is not correct, the load may not operate or the
• When mating Connectors, be sure to insert the plug all the operation indicator may not light.
way to the back of the socket before attempting to lock the • Always connect a load to the signal lines to operate a
Connectors. sensor or actuator.
• Do not use tools of any sort to mate the Connectors. Always
● Applicable Connectors
use your hands. Pliers or other tools may damage the
Connectors. • Always mount a Waterproof Cover (XS2Z-22) or Dust Cover
• When mating the Connectors to XS2 or other M12 (XS2Z-15) to any unused connector on the Connector
Connectors, tighten the lock by hand to a torque of 0.39 to Terminal Box.
0.49 N·m. ● Power Supply and Operation Indicators
• Confirm in the catalog that sensors and actuators are
applicable before using them. • The power supply indicator will be lit green while power is
• Always turn OFF the power supply before connecting or being supplied. The operation indicator will be lit red while
disconnecting connectors. the sensor or actuator is operating.
• Do not touch the mating surface of the connectors with wet • The XW3D is for a DC sensor or actuator. Do not use it for
hands. an AC sensor or actuator.
• Wipe away any water around the connectors. • Connector Terminal Boxes are available with either 2-wire
• Do not allow metal scraps or dust to enter the mating section. or 3-wire internal connections, as indicated on the case.
3-WIRE 2-WIRE 3-WIRE 3-WIRE 3-WIRE
NPN PNP NPN (2) PNP (2)

64
 Round Water-resistant Connectors (M12 Threads)

XS2
Water- and Environment-resistive FA
Connectors Save Wiring and Maintenance
Effort
• Compact FA connectors meet IP67 requirements and ensure
a 94V-0 fire retardant rating.
• A wide array of connectors makes a wiring system more
modular, simplifies maintenance, and reduces downtime.
• Connectors with Cables and Connector Assemblies are available.
• Three types of Connector Assembly: Crimping, soldering, and
screw-on.
• Connectors with Cables are UL certified.
• Based on IEC61076-2-101 (IEC60947-5-2) and NECA 4202.

Refer to Safety Precautions on page 86.

Ratings and Specifications Materials and Finish

Rated current 4A Item XS2F/H/W XS2M/R/P XS2C/G
Rated voltage 250 VAC/VDC Materials Phosphor bronze Brass
Contacts
Finish Nickel base, 0.4-μm gold plating
Contact resistance (Connector) 40 mΩ max. (20 mV max., 100 mA max.)
Thread Materials Brass *
Insulation resistance 1,000 MΩ min. (at 500 VDC)
bracket Finish Nickel plated *
1,500 VAC for 1 min (leakage current: PBT resin PA resin PBT resin
Dielectric strength (Connector) Materials
1 mA max.). Pin block (UL94V-0) (UL94V-0) (UL94V-0)
Degree of protection IP67 (IEC60529) Finish For DC: light gray; for AC: dark gray
Insertion tolerance 200 times O-ring/rubber bushing Rubber
Cable diameter: 6 mm 98 N/15 s Soft PBT resin PBT resin
Cover ---
Cable holding strength 4 to 5 mm 49 N/15 s (UL94V-0) (UL94V-0)
3 mm 29 N/15 s UL AWM2464 CL3,
6 mm dia.
Ambient operating temperature Fire-retardant,
Operating: − 25°C to 70°C AWG20 (0.5mm2) --- ---
range Robot cable
Structure:
Ambient humidity range 20% to 85% 0.08 mm/110 wires
Non-polar DC 6 mm dia.
Connectors AWG20 (0.5mm2)
--- ---
with Standard Structure:
Cable 0.12 mm/45 wires
E2E models with
UL AWM2464 CL3,
conventional
6 mm dia.
Cable connector pin
AWG20 (0.5mm2) --- ---
with Fire-
Structure:
retardant, Robot
0.08 mm/110 wires
cable
6 mm dia.
Heat-resistant
AWG20 (0.5mm2)
cable up to --- ---
Structure:
105°C
0.12 mm/45 wires
6.6 mm dia.
Spatter- AWG20 (0.5mm2)
--- ---
resistant Cables Structure:
0.08 mm/110 wires
*The T-joint of the XS2R is aluminum/white.

Socket Appearance
DC type AC type
Male (plug) Female (socket) Male (plug) Female (socket)
contacts contacts contacts contacts

1 2 1 2
4 4

2 1 3 2 1 3
3 4 3 4

Note: The AC and DC connectors are different as shown here and therefore
cannot be connected together.

65
 XS2
List of Products
Name Model Appearance

XS2W Sockets and Plugs on Cable Ends

XS2F Sockets on One Cable End

1. Connectors attached to Cable

XS2F Sockets on One Cable End with Indicator

XS2H Plugs on One Cable End

XS2G Plug Assemblies

XS2C Socket Assemblies

2. Connector Assemblies
(Crimping, Soldering, or
Screw-on)
XY2F Crimp Tool (for Crimping Connectors)
Used to enable using
connectors for sensor cables
and relay cables.

XW4Z Screwdriver (for Screw-on Connectors)

3. Terminal Box Connectors

XS2P Panel-mounting Sockets
Used to enable using
connectors for terminal boxes.

A B

T-Joints C
4. T-Joints and Y-Joints
XS2R T-Joint/Y-Joint
Used for branching and for Plug/Socket Connectors
daisy-chain connections.
Y-Joints

5. Sensor Connector Assemblies Embedded Plugs with

Screw Threads
XS2M Plugs
Used to enable using Embedded Plugs with
connectors in sensors. No Screw Threads

Flange-mounting Plugs
6. Panel-mounting Connectors
XS2M Plugs
Used to enable using I/O box
connectors mounted to panels. Screw-mounting Plugs

66
 XS2

XS2W Sockets and Plugs on Cable Ends

Model Number Legend
Use this model number legend to identify products from their model number. When ordering, use a model number from the table in Ordering Information.

XS2W-D@2@-@@1-@@
1 2 3 4 5 6 7 8 9

1. Type
W: Connectors connected to cable, socket and plug on cable ends

2. AC/DC (Mating Section Form)

D: For DC

3. Connector Poles
4: 4 poles
5: 5 poles

4. Contact Plating
2: 0.4-μm gold plating

5. Cable Connection Direction

1: Straight/straight
2: Right-angle/Right-angle
3: Straight (Socket)/Right-angle (Plug)
4: Right-angle (Socket)/straight (Plug)

6. Cable Length
A: 0.3 m (straight/straight only)
B: 0.5 m (straight/straight only)
C: 1 m (straight/straight only)
D: 2 m
E: 3 m (straight/straight only)
F: 4 m (straight/straight only)
G: 5 m
H: 7 m (straight/straight only)
J: 10 m (straight/straight only)
K: 15 m (straight/straight only)
L: 20 m (straight/straight only)

7. Connections
Pin No. Terminal No.
1 2 3 4 1 2 3 4 5

8: Brown White Blue Black (for DC) G: Brown White Blue Black Gray

8. Connectors on One End/Both Ends

1: Both ends

9. Cable Specifications
A: Standard cable
F: Fire-retardant, Robot cable
SA: Spatter-resistant Cable

67
 XS2

XS2W Sockets and Plugs on Cable Ends

● Connectors with Fire-retardant, Robot cable XS2W-D42@-@81-F
● Spatter-resistant Cable XS2W-D421-@81-SA

Dimensions (Unit: mm)

Straight/Straight Connectors

14.9 dia. 14.9 dia.

40.7 44.7
L

Right-angle/Right-angle Connectors
14.9 dia.
14.9 dia.

28.3 32.3

25.3 25.3 Wiring Diagram for 4 Cores

L
Contact No. Cable lead
Straight/Right-angle Connectors colors
14.9 dia. 1 1 Brown
2 2 White
3 3 Blue
4 4 Black
(DC)

32.3

14.9 dia.
Wiring Diagram for 5 Cores
40.7 25.3
Contact No. Cable lead
L colors
Right-angle/Straight Connectors 1 1 Brown
2 2 White
3 3 Blue
14.9 dia. 4 4 Black
5 5 Gray

28.3

14.9 dia.

25.3 44.7
L

Ordering Information

Cable Cable connection Cable No. of Cable core cross- Cable DC UL

Specifications direction diameter cable cores sectional area (mm2) length (m)
Model Minimum order -listed
(mm)
1 XS2W-D421-C81-F 10
2 XS2W-D421-D81-F
Straight/Straight 5
5 XS2W-D421-G81-F
10 XS2W-D421-J81-F 1
Fire-retardant, Right-angle/ 6.0 mm 2 XS2W-D422-D81-F
Yes
Robot cable Right-angle dia. 5 XS2W-D422-G81-F
4 0.5
Straight (Socket)/ 2 XS2W-D423-D81-F
5
Right-angle (Plug) 5 XS2W-D423-G81-F
Right-angle (Socket)/ 2 XS2W-D424-D81-F
Straight (Plug) 5 XS2W-D424-G81-F
Spatter- 6.6 mm 2 XS2W-D421-D81-SA
Straight/Straight 5 ---
resistant Cables dia. 5 XS2W-D421-G81-SA
Note: Ask your OMRON representative about other cable lengths, and about 5-core cables.

68
 XS2

XS2F Socket on One Cable End

Model Number Legend
Use this model number legend to identify products from their model number. When ordering, use a model number from the table in Ordering Information.

XS2F-@@2@-@@0-@@
1 2 3 4 5 6 7 8 9 8. Connectors on One End/Both Ends
1. Type 0: One end
F: Connector connected to cable, socket on one
9. Cable Specifications
cable end
A: Standard cable
2. AC/DC (Mating Section Form) F: Fire-retardant, Robot cable
A: For AC E: Heat-resistant cable up to 105°C
D: For DC SA: Spatter-resistant Cable
E: For DC, stainless steel lock E type and SA type is a 4-core cable.
3. Connector Poles
4: 4 poles Designations for DC Polarity (For Limit Switches and
5: 5 poles Sensors)
4. Contact Plating
6. Cable Length
2: 0.4-μm gold plating
3: 2 m
5. Cable Connection Direction 4: 5 m
1: Straight
7. Connections
2: Right-angle
Pin No.
6. Cable Length 1 2 3 4
A: 0.3 m 1: --- --- Black White
B: 0.5 m
C: 1 m 8. Connectors on One End/Both Ends
D: 2 m 0: One end
E: 3 m
F: 4 m 9. Cable Specifications
G: 5 m Not designated.
H: 7 m Note: Model number standards are different for items 6, 7, and 9 for non-polar
connectors.
J: 10 m
K: 15 m
L: 20 m
Only the 2 m (D) and 5 m (G) cables are available for
cables with 5 poles.

7. Connections
Terminal No. Terminal No.
1 2 3 4 1 2 3 4 5

A: Brown --- --- Blue (for DC) G: Brown White Blue Black Gray
B: --- --- Brown Blue (for DC)
C: Brown --- Blue Black
D: --- --- Blue Brown
8: Brown White Blue Black (for DC)
9: Brown White Blue Black (for AC)

69
 XS2

XS2F Sockets on One Cable End

● Connectors with Fire-retardant, Robot Cable XS2F-@42@-@@0-F
● Non-polar DC Connectors with Standard Cable XS2F-@42@-@@0
● E2E models with conventional connector pin with Fire-retardant, Robot Cable XS2F-D42@-@D0
● Heart-resistant Cable up to 105°C XS2F-E42@-@80-E
● Spatter-resistant Cables XS2F-D421-@80-SA

Dimensions (Unit: mm)

Straight Connectors
M12 × 1 45° M12 × 1 45°
6 dia.
5 dia. 5 dia.

14.9 dia.

DC AC 40.7 30 5
L 50

Right-angle Connectors
L
25.3 6 dia.

28.3 30 5
50

14.9 dia.
M12 × 1 M12 × 1
5 dia. 5 dia.
DC AC

45° 45°

Wiring Diagram
Two-core model Three-core model Four-core model
Fire-retardant, XS2F-@42@ Contact No. Cable lead
colors
Robot cable -@@0-F 1 Brown
2
Spatter-resis- XS2F-D421- 3
4 Blue
Contact No. Cable lead
colors
Contact No. Cable lead
colors
tant Cables* @80-SA (DC)
1 Brown 1 Brown
2 2 White
Blue 3 Blue
Heat-resistant XS2F-E42@- Contact No. Cable lead
colors
3
4 Black 4 Black
@80-E
(DC) (DC/AC)
Cables up to 1
2
Brown
105°C * 3
4 Blue
(AC)

Standard Contact No. Cable lead

colors
cable XS2F-@42@ 1
2 --- ---
(non-polar -@@0 3
4
Black
White
DC)
Fire-retardant,
Robot cable Contact No. Cable lead
colors
(E2E models XS2F-D42@ 1
2 --- ---
with -@D0 3 Blue
4 Brown
conventional
connector pin)
*Spatter-resistant Cables and Heat-resistant Cables (105°C) are available only for four cores and DC.

70
 XS2
Ordering Information

Cable DC AC
Cable No. of Cable core Cable
Cable outer Minimum UL-
connection cable cross-sectional length
Specifications diameter Model Model order listed
direction cores (mm) area (mm2) (m)
2 XS2F-D421-CA0-F XS2F-A421-CB0-F
3 1 XS2F-D421-CC0-F --- 10
4 XS2F-D421-C80-F XS2F-A421-C90-F
2 XS2F-D421-DA0-F XS2F-A421-DB0-F
3 2 XS2F-D421-DC0-F ---
4 XS2F-D421-D80-F XS2F-A421-D90-F
Straight 5
2 XS2F-D421-GA0-F XS2F-A421-GB0-F
3 5 XS2F-D421-GC0-F ---
4 XS2F-D421-G80-F XS2F-A421-G90-F
2 XS2F-D421-JA0-F XS2F-A421-JB0-F
3 10 XS2F-D421-JC0-F --- 1
Fire-retardant, 4 XS2F-D421-J80-F XS2F-A421-J90-F
Yes
Robot cable 2 XS2F-D422-CA0-F XS2F-A422-CB0-F
3 1 XS2F-D422-CC0-F --- 10
4 XS2F-D422-C80-F ---
2 XS2F-D422-DA0-F XS2F-A422-DB0-F
3 2 XS2F-D422-DC0-F ---
4 XS2F-D422-D80-F ---
Right-angle 6.0 mm 5
2 XS2F-D422-GA0-F XS2F-A422-GB0-F
dia.
3 0.5 5 XS2F-D422-GC0-F ---
4 XS2F-D422-G80-F ---
2 XS2F-D422-JA0-F XS2F-A422-JB0-F
3 10 XS2F-D422-JC0-F --- 1
4 XS2F-D422-J80-F ---
2 2 XS2F-D421-310 XS2F-A421-310
Straight
Standard cable 2 5 XS2F-D421-410 XS2F-A421-410
---
(non-polar) 2 2 XS2F-D422-310 XS2F-A422-310
Right-angle
2 5 XS2F-D422-410 XS2F-A422-410
Fire-retardant, 2 2 XS2F-D421-DD0 ---
Straight
Robot cable (E2E 2 5 XS2F-D421-GD0 ---
models with 2 2 XS2F-D422-DD0 --- ---
conventional Right-angle 5
2 5 XS2F-D422-GD0 ---
connector pin)
2 XS2F-E421-D80-E ---
Heat-resistant Straight
5 XS2F-E421-G80-E ---
cable up to 4 ---
2 XS2F-E422-D80-E ---
105°C * Right-angle
5 XS2F-E422-G80-E ---
Spatter- 6.6 mm 2 XS2F-D421-D80-SA ---
Straight 4 ---
resistant Cables dia. 5 XS2F-D421-G80-SA ---
Note: Ask your OMRON representative about other cable lengths.
*The heat-resistant fixture material is SUS316L stainless steel without surface treatment.

71
 XS2
Applicable Proximity Sensors

Refer to page the E2E Datasheet for information on connecting to E2E Proximity Sensors

● 5-pole Connectors for DC XS2F-D521-@G0-A

Dimensions (Unit: mm)

Straight Connectors
Note: Use the XS2H-D521-@G0-A in
combination with the XS2F-
D521-@G0-A.
M12 × 1 45°
6 dia.
5 dia.
14.9 dia.

40.7 30 5
L 50

Wiring Diagram Pin Arrangements (Engagement Side)

Contact No. Cable lead

colors 2
1 Brown
2 White 5
3 Blue
4 Black
5 Gray 1 3
4

Ordering Information
No. of cable Cable core Cable length DC
cores cross-sectional (m)
area (mm2) Model Minimum order
2 XS2F-D521-DG0-A 5
5 0.3
5 XS2F-D521-GG0-A 5
Note: Ask your OMRON representative about other cable lengths.

72
 XS2

XS2F Sockets on One Cable End

● Screw Loosening-preventing Structure XS2F-G/H

Dimensions (Unit: mm)

Straight Connectors
M12 × 1 45° M12 × 1 45°
6 dia.
5 dia. 5 dia.

14.9 dia.

DC AC 40.7 30 5
L 50

Right-angle
L
25.3 6 dia.

28.3 30 5
50

M12 × 1 M12 × 1
5 dia. 5 dia.
DC AC

45° 45°

Ordering Information
Cable No. of cable Cable length DC AC
cores (m) Minimum
connection
Model Model order
direction
5 XS2F-G421-G80-F XS2F-H421-G90-F 5
Straight
10 XS2F-G421-J80-F XS2F-H421-J90-F 1
4
5 XS2F-G422-G80-F XS2F-H422-G90-F 5
Right-angle
10 XS2F-G422-J80-F XS2F-H422-J90-F 1

Screw Loosening-preventing Structure

Appearance

Black nickel plating

Structure

Bumped surface Ribbed surface

With the above structure, the bumps every 45° on the lock mechanism engage with the ribs on the housing to prevent the connector
from coming loose when it is mated.

73
 XS2

XS2F Sockets on One Cable End with Indicator

Model Number Legend

XS2F-M12 PVC @ A @@M@ LED

1 2 3 4 5 6 7 8

1. Type 4. Connector Poles 7. Applicable Sensors

F: Connector connected to cable, 3: 3 poles P: PNP
sockets on one cable end 4: 4 poles N: NPN
2. Mating Section Form 5. Cable Connection Direction 8. With indicator
M12: M12 A: Right-angle LED: With indicator
3. Cable material 6. Cable Length
PVC: PVC 2: 2 m
5: 5 m
10: 10 m

Dimensions (Unit: mm)

L
35 5
30
28.2

28
9.1
50

14.9 dia.

45° M12×1

Wiring Diagram
3 poles 4 poles
NPN type PNP type PNP type
1 + BROWN 1 + BROWN 1 + BROWN
2 WHITE
YELLOW GREEN 4 BLACK 4 BLACK

R1 R2 R3
4 BLACK
YELLOW GREEN D1 D2 D3
3 - BLUE 3 - BLUE 3 - BLUE

Ordering Information

Cable Cable core Cable

Cable Cable connection outer No. of Minimum UL-
cross-sectional length LED Model
Specifications direction diameter cable cores order listed
(mm) area (mm2) (m)
2 XS2F-M12PVC3A2MPLED
5 PNP XS2F-M12PVC3A5MPLED
5 mm 10 XS2F-M12PVC3A10MPLED
3
dia. 2 XS2F-M12PVC3A2MNLED
PVC Right-angle 0.34 5 NPN XS2F-M12PVC3A5MNLED 1 Yes
10 XS2F-M12PVC3A10MNLED
2 XS2F-M12PVC4A2MPLED
5.4 mm
4 5 PNP XS2F-M12PVC4A5MPLED
dia.
10 XS2F-M12PVC4A10MPLED

74
 XS2

XS2H Plugs on One Cable End

Model Number Legend

XS2H-@@21-@@0-@@
1 2 3 4 5 6 7 8 9

1. Type
H: Connector connected to cable, plug on one cable end

2. AC/DC
A: For AC
D: For DC

3. Connector Poles Using this model number legend to identify products from their
4: 4 poles model number. When ordering, use a model number from the
5: 5 poles table in Ordering Information.

4. Contact Plating
2: 0.4-μm gold plating

5. Cable Connection Direction

1: Straight

6. Cable Length
A: 0.3 m
B: 0.5 m
C: 1 m
D: 2 m
G: 5 m

7. Connections
Terminal No. Terminal No. Terminal No.
1 2 3 4 1 2 3 4 1 2 3 4 5

8: Brown White Blue Black (for DC) A: Brown --- --- Blue (for DC) G: Brown White Blue Black Gray
9: Brown White Blue Black (for AC) B: --- --- Brown Blue (for AC)
C: Brown --- Blue Black (for DC)

8. Connectors on One End/Both Ends

0: One end

9. Cable Specifications
A: Standard cable
F: Fire-retardant, Robot cable
SA: Spatter-resistant Cable

75
 XS2

XS2H Plugs on One Cable End

● Connectors with Fire-retardant, Robot Cable XS2H-@421-@@0-F
● Spatter-resistant Cable XS2H-D421-@80-SA
Dimensions (Unit: mm)

Straight Connectors
M12 × 1 45° 5 dia. 45° 44.7
6 dia.
5 dia.

14.9 dia.

DC AC 30 5
L 50
Wiring Diagram

Contact No. Cable lead

colors
1 Brown
2
3 Contact No. Cable lead Contact No. Cable lead
4 Blue colors colors
(DC)
1 Brown 1 Brown
2 2 White
Contact No. Cable lead 3 Blue 3 Blue
colors 4 Black 4 Black
(DC) (DC/AC)
1
2
3 Brown
4 Blue
(AC)

Two-core Model Three-core Model Four-core Model

● Connectors on DC Cable (Five Poles) XS2H-D521-@G0-A (for DC)

Dimensions (Unit: mm)

Straight Connectors Note: Use the XS2F-D521-@G0-A in

combination with the XS2H-D521-
M12 × 1 45°
6 dia.
@G0-A.
5 dia.

14.9 dia.

44.7 30 5
L 50
Wiring diagram Pin Arrangements (Engagement Side)
Contact No. Cable lead
colors 1
Brown
1
1
2 White 5
3 Blue 5
4 Black
5 Gray 2 4
2 4
3
3
Five-core Model

Ordering Information
Cable DC AC
No. of Cable No. of Cable core Cable
Cable outer Minimum UL-
connector connection cable cross-sectional length
Specifications diameter Model Model order listed
poles direction cores area (mm2) (m)
(mm)
2 XS2H-D421-AA0-F XS2H-A421-AB0-F
3 0.3 XS2H-D421-AC0-F ---
Fire-retardant, 4 6.0 mm XS2H-D421-A80-F XS2H-A421-A90-F
4 Yes
Robot cable 2 dia. XS2H-D421-CA0-F XS2H-A421-CB0-F
0.5
3 1 XS2H-D421-CC0-F ---
Straight 10
4 XS2H-D421-C80-F XS2H-A421-C90-F
Spatter- 6.6 mm 0.3 XS2H-D421-A80-SA ---
4 4 ---
resistant Cables dia. 1 XS2H-D421-C80-SA ---
6.0 mm 0.3 XS2H-D521-AG0-A ---
Standard cable 5 5 0.3 ---
dia. 1 XS2H-D521-CG0-A ---

76
 XS2

XS2@ Sensor I/O Connectors on Cables (8-pole)

Ordering Information

Cable connection Applicable wire

Connector type Number of cores Cable length (m) Model
direction diameter
XS2P-D821-2
Panel-mounting socket
--- AWG22 to 28 --- --- XS2P-D822-2
Panel-mounting plug XS2M-D824-4
0.3 XS2H-D821-AH0-C
Plug on one cable end
1 XS2H-D821-CH0-C
2 XS2F-D821-DH0-C
Socket on one cable end Straight --- 8
5 XS2F-D821-GH0-C
2 XS2W-D821-DH1-C
Plug and socket on cable ends
5 XS2W-D821-GH1-C

Pin Numbers and Cable Lead Colors

Pin number
XS2F/XS2H/XS2W cable lead 1 2 3 4 5 6 7 8
colors White Brown Green Yellow Gray Pink Blue Shield

Ratings and Characteristics Materials and Finish

Rated current 1.5 A Brass/nickel base,
Contacts
Rated voltage 36 VDC 0.4-μm goldplating
40 mΩ max. Bracket, body, M16 nuts Brass/nickel plated
Contact resistance
(at 20 mVDC max. and 100 mA max.) Pin block PBT resin (UL94V-0)/light gray
Insulation resistance 1,000 MΩ min. (at 500 VDC) Cover *1 PBT resin (UL94V-0)
1,000 VAC for 1 min Seal rubber and O-ring
Dielectric strength Rubber
(leakage current: 1 mA max.) *2
Degree of protection IP67 *1. XS2F/XS2H/XS2W only.
*2. O-rings are on sockets only.
Insertion durability 200 times min.
Operating temperature −25 to 70°C

Wiring Example
Relay box,
Sensor, actuator, etc.
In-panel terminal block

XS2M XS2P
XS2W

XS2H XS2F

77
 XS2
Dimensions (Unit: mm)

XS2H Plug on One Cable End (M12)

2 1
6 dia.
3 7

14.9 dia.
4 6
8 5
M12 × 1 30 5
44.7
L 50

XS2F Socket on One Cable End (M12)

1 2
6 dia.
7 3

14.9 dia.
6 4
8 5
M12 × 1 30 5
40.7
L 50

XS2W Plug and Socket on Cable Ends (M12)

M12 × 1
2 5 8
1
6 dia. 6 4
7 3

14.9 dia. 14.9 dia.

7 3
6 4
8 1 2
5 44.7
M12 × 1
40.7
L

XS2P-D821-2 Panel-mounting Socket (M12) with Solder XS2M-D824-4 Panel-mounting Plug (M12) with Solder Cup
Cup Pins and Rear Lock Pins and Front Lock

Panel
20.9
Panel 8.7 5
3
1.5 M16 nut 3 33 20 dia.
Seal rubber

7
2

2
3

1
1

3
7 10.6 dia.
7

7
1

4
6

20 dia. 14 dia.
5

6
2

5
5

6
3
4

M12 × 1
M12 × 1 2.5 10.5 3 M16 × 1 M16 × 1
M16 nut
20.4
5 Seal rubber

XS2P-D822-2 Panel-mounting Socket (M12) with Solder

Cup Pins and Front Lock Panel Cutouts Connector Pin Numbers
(from Mating Side)
+0.1 2 1
7 0 +0.2 1 2
16 0 dia.

3 7 7 3
Panel 3 Seal rubber
1.5
M16 nut
4 6 6 4
7 8 8
1

5 5
2

20 dia. 14 dia. 14 dia. 24 min.

3

Plug Socket
4

Note 1. Mounting panel thickness: 1 to 4 mm.

M12 × 1 M16 × 1 8.7 6 3 2.Applicable core wire size for solder cup pins: 0.5 mm2 max.
5
20.4 3.The M16 nut and seal rubber are included.

78
 XS2

XS2G Crimping/Soldering Plug Assemblies

Dimensions (Unit: mm)

XS2G-@4C@ (Crimping Model)

XS2G-@42@ (Soldering Model) 45° 45°
5 dia. 5 dia. M12 × 1
Straight Connectors
14.9 dia. 14.2 dia.

47.1
DC AC

XS2G-D42@ (Soldering Model) 45° 5 dia. 35.7

Right-angle Connectors
14.9 dia. M12 × 1

23

DC

Ordering Information
Suitable cable dia. Suitable core Suitable Cable Connection DC AC Minimum
Sheath connection
(mm) size (mm2) material direction method Model Model order
0.18 to 0.3
Crimping XS2G-D4C1 XS2G-A4C1
6 mm dia. model 0.5 to 0.75 * Straight
(5 to 6 mm dia.) Soldering XS2G-D421 XS2G-A421
0.5 max.
Right-angle Soldering XS2G-D422 ---
0.18 to 0.3
Crimping XS2G-D4C3 XS2G-A4C3
4 mm dia. model 0.5 to 0.75 * PVC, PE, Straight
50
(4 to 5 mm dia.) PUR Soldering XS2G-D423 XS2G-A423
0.5 max.
Right-angle Soldering XS2G-D424 ---
0.18 to 0.3
Crimping XS2G-D4C5 XS2G-A4C5
3 mm dia. model 0.5 to 0.75 * Straight
(3 to 4 mm dia.) Soldering XS2G-D425 XS2G-A425
0.5 max.
Right-angle Soldering XS2G-D426 ---
*There are two types of contacts.
Note: Crimping plug contacts are sold separately.
Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.

XS2U Crimping Pin for XS2G

Dimensions (Unit: mm)

XS2U-312@ (Plug Pin) Note: A special tool must be used for crimping. For details, refer to page 89.

Slit
Dimensions
Suitable Dimension
(mm) No. of
1 dia.
C dia.
2 dia. 2.3 dia. Model core size
slits
(mm2) A B C
1.5
XS2U-3121 0.18 to 0.3 20.0 6.1 0.8 1
B
A XS2U-3122 0.5 to 0.75 20.1 6.2 1.3 0

Ordering Information
Suitable core size (mm2) Model Minimum order
0.18 to 0.3 XS2U-3121
100
0.5 to 0.75 XS2U-3122
Note: Orders are accepted in multiples of the minimum order.

79
 XS2

XS2C Crimping/Soldering Socket Assemblies

Dimensions (Unit: mm)

XS2C-@4C@ (Crimping Model)

XS2C-@42@ (Soldering Model)
45° 45°
Straight Connectors 5 dia. 5 dia.
M12 × 1 M12 × 1
14.9 dia. 14.2 dia.

DC AC 43.2

Right-angle Connectors 45° 5 dia. 45° 5 dia. 31.8

M12 × 1 M12 × 1
14.9 dia.

23

DC AC

Ordering Information
Suitable cable dia. Suitable core Suitable Cable Connection DC AC Minimum
Sheath connection
(mm) size (mm2) material direction method Model Model order
0.18 to 0.3
Crimping XS2C-D4C1 XS2C-A4C1
0.5 to 0.75 * Straight
6 mm dia. model 0.5 max. Soldering XS2C-D421 XS2C-A421
(5 to 6 mm dia.) 0.18 to 0.3
Crimping XS2C-D4C2 XS2C-A4C2
0.5 to 0.75 * Right-angle
0.5 max. Soldering XS2C-D422 XS2C-A422
0.18 to 0.3
Crimping XS2C-D4C3 XS2C-A4C3
0.5 to 0.75 * Straight
4 mm dia. model 0.5 max. PVC, PE, Soldering XS2C-D423 XS2C-A423
50
(4 to 5 mm dia.) 0.18 to 0.3 PUR
Crimping XS2C-D4C4 XS2C-A4C4
0.5 to 0.75 * Right-angle
0.5 max. Soldering XS2C-D424 XS2C-A424
0.18 to 0.3
Crimping XS2C-D4C5 XS2C-A4C5
0.5 to 0.75 * Straight
3 mm dia. model 0.5 max. Soldering XS2C-D425 XS2C-A425
(3 to 4 mm dia.) 0.18 to 0.3
Crimping XS2C-D4C6 XS2C-A4C6
0.5 to 0.75 * Right-angle
0.5 max. Soldering XS2C-D426 XS2C-A426
*There are two types of contacts.
Note: Crimping plug contacts are sold separately.
Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.

XS2U Crimping Pin for XS2C

Dimensions (Unit: mm)

XS2U-222@ (Socket Pin) Note: A special tool must be used for crimping. For details, refer to page 89.
Dimensions
Slit
Suitable Dimension
(mm) No. of
2 dia. 2.3 dia.
Model core size
C dia. slits
(mm2) A B C
1.5 XS2U-2221 0.18 to 0.3 16.7 6.1 0.8 1
B XS2U-2222 0.5 to 0.75 16.8 6.2 1.3 0
A

Ordering Information
Suitable core size (mm2) Model Minimum order
0.18 to 0.3 XS2U-2221
100
0.5 to 0.75 XS2U-2222
Note: Orders are accepted in multiples of the minimum order.

80
 XS2

XS2G Screw-on Plug Assemblies

Dimensions (Unit: mm)

XS2G-D5S7 (5-pole, Straight, Applicable Cable Outer Diameter: 8 mm)

XS2G-D5S9 (5-pole, Straight, Applicable Cable Outer Diameter: 7 mm)
XS2G-D4S7 (4-pole, Straight, Applicable Cable Outer Diameter: 8 mm)
XS2G-D4S9 (4-pole, Straight, Applicable Cable Outer Diameter: 7 mm)

M12 × 1 58.7

20 dia. 14.9 dia. 16 dia.

XS2G-D5S1 (5-pole, Straight, Applicable Cable Outer Diameter: 6 mm)

XS2G-D4S@ (4-pole, Straight, Applicable Cable Outer Diameter: 3, 4, or 6 mm)

M12 × 1 58.7

20 dia. 14.9 dia. 14 dia.

XS2G-D5S2 (5-pole, Right-angle, Applicable Cable Outer Diameter: 6 mm)

XS2G-D4S@ (4-pole, Right-angle, Applicable Cable Outer Diameter: 3, 4, or 6 mm)
M12 × 1 39.7

20 dia. 14.9 dia.

39.6

14 dia.

Ordering Information

Suitable Suitable Straight connectors Right-angle connectors

No. of Minimum
Suitable cable dia. (mm) core size Sheath (for DC) (for DC)
poles material order
(mm2) Model Model
8 mm dia. model (7 to 8 mm dia.) XS2G-D5S7 ---
5 7 mm dia. model (6 to 7 mm dia.) XS2G-D5S9 ---
6 mm dia. model (5 to 6 mm dia.) XS2G-D5S1 XS2G-D5S2
8 mm dia. model (7 to 8 mm dia.) 0.18 to PVC, PE, XS2G-D4S7 ---
50
7 mm dia. model (6 to 7 mm dia.) 0.75 PUR XS2G-D4S9 ---
4 6 mm dia. model (5 to 6 mm dia.) XS2G-D4S1 XS2G-D4S2
4 mm dia. model (4 to 5 mm dia.) XS2G-D4S3 XS2G-D4S4
3 mm dia. model (3 to 4 mm dia.) XS2G-D4S5 XS2G-D4S6
Note: XS2G Screw-on Plugs cannot be connected to side by side to the CN1 and CN2 connectors of XS2R Y-Joint Sockets/Plugs.
Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.

81
 XS2

XS2C Screw-on Socket Assemblies

Dimensions (Unit: mm)

XS2C-D5S7 (5-pole, Straight, Applicable Cable Outer Diameter: 8 mm)

XS2C-D5S9 (5-pole, Straight, Applicable Cable Outer Diameter: 7 mm)
XS2C-D4S7 (4-pole, Straight, Applicable Cable Outer Diameter: 8 mm)
XS2C-D4S9 (4-pole, Straight, Applicable Cable Outer Diameter: 7 mm)

M12 × 1 54.9

20 dia. 14.9 dia. 16 dia.

XS2C-D5S1 (5-pole, Straight, Applicable Cable Outer Diameter: 6 mm)

XS2C-D4S@ (4-pole, Straight, Applicable Cable Outer Diameter: 3, 4, or 6 mm)

M12 × 1 54.9

20 dia. 14.9 dia. 14 dia.

XS2C-D5S2 (5-pole, Right-angle, Applicable Cable Outer Diameter: 6 mm)

XS2C-D4S@ (4-pole, Right-angle, Applicable Cable Outer Diameter: 3, 4, or 6 mm)
M12 × 1 35.9

20 dia. 14.9 dia.

39.6

14 dia.

Ordering Information

Suitable Suitable Straight connectors Right-angle connectors

No. of Minimum
Suitable cable dia. (mm) core size Sheath (for DC) (for DC)
poles material order
(mm2) Model Model
8 mm dia. model (7 to 8 mm dia.) XS2C-D5S7 ---
5 7 mm dia. model (6 to 7 mm dia.) XS2C-D5S9 ---
6 mm dia. model (5 to 6 mm dia.) XS2C-D5S1 XS2C-D5S2
8 mm dia. model (7 to 8 mm dia.) 0.18 to PVC, PE, XS2C-D4S7 ---
50
7 mm dia. model (6 to 7 mm dia.) 0.75 PUR XS2C-D4S9 ---
4 6 mm dia. model (5 to 6 mm dia.) XS2C-D4S1 XS2C-D4S2
4 mm dia. model (4 to 5 mm dia.) XS2C-D4S3 XS2C-D4S4
3 mm dia. model (3 to 4 mm dia.) XS2C-D4S5 XS2C-D4S6
Note: Use one of the above cables. If you do not use one of these cables, there is a possibility that the performance can't be met.
Ask your OMRON representative about selecting a cable of other than above.

82
 XS2

XS2P Panel-mounting Sockets for Terminal Boxes

Dimensions (Unit: mm)

XS2P-@421-2 (with Solder Cup Pins)

Rear Lock Model Panel
Rubber bushing M16 × 1
M12 × 1 M12 × 1

20 dia.14.6 dia.

7.8 2.5 7
DC AC 20.5
24

XS2P-@422-1 (with DIP Pins)

XS2P-@422-2 (with Solder Cup Pins)
Panel Panel
Front Lock Model M16 × 1 Rubber bushing M16 × 1 Rubber bushing
M12 × 1 M12 × 1 5 dia.
2 dia.

14 dia. 20 dia. 14 dia. 16 dia.

7 7 6 8.7 2.5 17
20.5 17
DC AC
24 23.5
27

With Solder Cup Pins With DIP Pins

Panel Cutout PCB-mounting Dimensions

+0.1
7 0 16
+0.15
dia.
0
5
Land

Four, 2.2-dia.holes
24 min.
24 min.
Note: The panel thickness is 1 to 4 mm.

Ordering Information

Applicable wire DC AC
Lock method Pin shape Minimum order
diameter Model Model
Rear lock Solder cup pin XS2P-D421-2 XS2P-A421-2
Solder cup pin AWG20 to 28 XS2P-D422-2 XS2P-A422-2 50
Front lock
DIP pin XS2P-D422-1 XS2P-A422-1

83
 XS2

XS2R Y-Joint Plug/Socket Connectors

Dimensions (Unit: mm)

XS2R-D426-@11-F
Connectors on Both Cable Ends (Y-Joint Plug/Socket) Wiring Diagram

15.0 M12 × 1 Socket 45.5 1

CN2 2
4.6 dia. CN2
3
1 2
14.9 dia. Plug
6 dia. 4 4
4 3
14.9 dia. 4 3 3
35.0 18.0 1 2 2
1 1
1 2
4 3
2
14.9 dia. CN1
8.5 M12 × 1 3
Blue marking 13.6 44.7
CN1 4
L

XS2R-D426-@10-F
Wiring Diagram
Connectors on One Cable End (Y-Joint Plug/Socket)
1
15.0 M12 × 1 Socket 45.5
CN2
2
CN2
4.6 dia. 3
14.9 dia. 4
1 2 Black
4 3 6 dia.
Blue
White
35.0 18.0
1 Brown

1 2 2
4 3 14.9 dia. CN1
8.5 3
Blue marking 13.6 30 5 4
CN1
L 50

XS2R-D426-1 Wiring Diagram

Y-Joint Plug/Socket without Cable XS2R-D426-1 XS2R-D426-5
4 4
3 3
CN2 CN2
2 2
1 1
27
7
15 M12 × 1 Socket 4.5 dia. 4
CN2 4 4 4 3
CN0
14.9 dia. 3 3 3 2
1 2 CN1 CN0 CN1
4 3 2 2 2 1
CN0 Plug 24.5
1 1 1
(37) 18.0
14.9 dia. 4
1
1
2 2 3 XS2R-D426-81 XS2R-D426-82
4 3 14.9 dia. 12.5 4 4
CN1 3 3
CN2 CN2
58.3 M12 × 1 2 2
1 1
Blue marking
4 4
4 3 4 3
CN0 CN0
CN1 3 2 CN1 3 2
2 1 2 1
1 1

Ordering Information

DC
Type Connector
Cable length L (m) Model Minimum order
0.5 XS2R-D426-B11-F
1 XS2R-D426-C11-F
Connectors on both cable ends
2 XS2R-D426-D11-F
With cable 5
3 XS2R-D426-E11-F
2 XS2R-D426-D10-F
Connector on one cable end
5 XS2R-D426-G10-F
XS2R-D426-1
XS2R-D426-5
Without cable Y-Joint plug/socket --- 10
XS2R-D426-81
XS2R-D426-82
Note: XS2G Screw-on Plugs cannot be connected side-by-side to the CN1 and CN2 connectors.
Consider using a crimping or soldering model instead. Refer to page 79 for details.

84
 XS2

XS2R T-Joint Plug/Socket Connectors

Dimensions (Unit: mm)

XS2R-D422-1 Wiring Diagram

XS2R-D422-5 XS2R-D422-1
Aggregate Models A (Female) B (Female)
4 4
3 3
50.6
M12 × 1 24.6 2 2
1 1

14.6 dia. A B
1 2 3 4

C 29 C (Male)
M12 × 1
XS2R-D422-5
A (Female) B (Female)
4 4
3 3
2 2
1 1

1 2 3 4

C (Male)

XS2R-D423-1 Wiring Diagram

50.6
Bifurcated Model A (Male) B (Male)
24.6
4 4
3 3
A B
2 2
1 1
M12 × 1
C 29

1 2 3 4

14.6 dia. C (Female)

M12 × 1

XS2R-D424-1 Wiring Diagram

Daisy-chain Model 50.6
A (Female) B (Male)
M12 × 1 24.6
4 4
3 3
14.6 dia. A B
2 2
1 1
M12 × 1
C 29

1 2 3 4

C (Female)

Ordering Information
DC
Type
Model Minimum order
XS2R-D422-1
Aggregate model
XS2R-D422-5
20
Bifurcated model XS2R-D423-1
Daisy-chain model XS2R-D424-1

85
 XS2
XS2R Application Examples
XS2R-D422-1 (Aggregate Model) • A pair of Two-wire Sensors or
Three-wire Sensors can be
Sensor Sensor
connected as shown in the
XS2G/XS2H XS2R-D422-1 XS2G/XS2H
illustration.
A B • The XS2R-D422-5 has feedthrough
connections, thus working as a
C connector for the extension cable.
Photoelectric sensor
Photoelectric sensor
XS2W/XS2F/XS2C

XS2R-D423-1 (Bifurcated Model)

XS2W/XS2F/XS2C XS2R-D423-1 XS2W/XS2F/XS2C

A B • Two or Three-wire Sensor signals

can be bifurcated.
C

XS2G/XS2H Proximity sensor

PLC (A)

Sensor PLC (B)

XS2R-D424-1 (Daisy Chain Model)

A B A B A B

C C C
• Two-wire Sensors with contact
output can be connected through a
daisy chain to obtain AND output.

Sensor1

Sensor2 Sensor2 Sensor3

Safety Precautions

Precautions for Correct Use

Do not use this product under ambient conditions that exceed
the ratings.
Before using the XS2R for Sensors, make sure that the wiring
of the Sensors and the internal connections of the XS2R are
correct.

86
 XS2

XS2M Sensor-embedded Plugs

Dimensions (Unit: mm)

XS2M-D421 (DC)
Mounted Dimensions
XS2M-A421 (AC)
(Embedded Plug with Screw Threads) Resin
M12 × 1 filled
45° 45° 6.5
5 dia. 5 dia. O-ring
9.45+0.05
−0 dia.

10.5 dia. 8 dia. 9.4 dia.

DC AC 1.2 4 0.7
10 6.7 min.
16 Note: After mounting, anchor the solder cups
by injecting resin.

XS2M-D422 (DC)
Mounted Dimensions
XS2M-A422 (AC)
(Embedded Plug without Screw Threads) 15.7 min.
Resin
5 dia. 5 dia. 9.6 dia. O-ring filled
45° 45°

9.45+0.05
−0 dia.
10.5 dia. 9.4 dia.

1.2
DC AC 10.8
1.5 6.5
16 0.7
M12 × 1
Note: After mounting, anchor the solder cups
by injecting resin.

XS2M Panel-mounting Plugs

Dimensions (Unit: mm)

XS2M-D423 (For DC)

Panel Cutouts
XS2M-A423 (For AC) M12 × 1
Rubber bushing +1
(Flange-mounting Model) 45°
5 dia.
45°
5 dia. 1.5
6.5 10 0
2.5 dia. Four,
3.2 dia.

20 14 20 14 10.5 dia. 9.4 dia.3.2 dia. 14±0.1

14 14 10
21
20 20 16 0.7 14±0.1
21 min.
DC AC

XS2M-@424-1 (With DIP Pins) Panel Cutouts

XS2M-@424-2 (With Solder Cup Pins) 7
+0.2 +0.3
0 16 0 dia.
(Screw-mounting Model)
Panel Rubber bushing
1.5
M16 × 1
2 dia. 5 dia.
M12 × 1

16 dia. 20 dia. 24 min.

Note: The panel thickness is 1 to 4 mm.

PCB-mounting Dimensions
7 7 3 2.5 17 5
DC AC 1.5
6.5 6.8
9 3.5 Land
8.7
27.7 5

Four,
24 min.
2.2-dia. holes

87
 XS2
Ordering Information
Applicable wire DC AC
Mounting method Pin shape Minimum order
diameter Model Model
Embedded with screw threads XS2M-D421 XS2M-A421
Embedded with no screw threads Solder cup pin AWG22 to 28 XS2M-D422 XS2M-A422
Flange-mounting XS2M-D423 XS2M-A423 50
DIP pin --- XS2M-D424-1 XS2M-A424-1
Screw-mounting
Solder cup pin AWG20 to 28 XS2M-D424-2 XS2M-A424-2

Connector Covers
Water-resistive Covers XS2Z-11 M12 male screw
XS2Z-11

M12 × 1

XS2Z-22 XS2Z-22 M12 × 1

M12 × 1 female screw (thread bracket) You can use the Water-resistant Cover
when the connector is not connected to
ensure an IP67 degree of protection. When
mounting the Water-resistive Cover to a
Connector, be sure to apply a torque range
between 0.39 and 0.49 N·m to tighten the
Water-resistive Cover.

Suitable connector
Model Minimum order Material
Model Mounting portion
XS2G/XS2H/XS2M/XS2R/XS2W/XS5H/
XS2Z-11 M12 male screw
XS5M/XS5W
50 Brass/nickel plated
XS2C/XS2R/XS2F/XS2P/XS2W/XW3B/
XS2Z-22 M12 female screw (thread bracket)
XS5F/XS5W/XS5R/XS5P/XW3D

Dust Covers
XS2Z-13 M12 male screw
XS2Z-13

XS2Z-15/XS2Z-14 M12 female screw (thread bracket) The Dust Cover is for dust prevention and
XS2Z-15 XS2Z-14
does not ensure IP67 degree of protection.
When mounting the Dust Cover to a
connector, be sure to press the Dust Cover
onto the Connector until the Connector is
Pin block (female pins)
fully inserted into the Dust Cover.

Suitable connector
Model Minimum order Material
Model Mounting portion
XS2Z-13 XS2G/XS2H/XS2M/XS2R M12 male screw
XS2Z-14 50 Rubber/black XS2C/XS2R/XS2F/XS2P/ Pin block (female pins)
XS2Z-15 XW3A/XW3B M12 female screw (thread bracket)

88
 XS2

Loosening-preventing C Ring
XS2Z-18 This C ring prevents the M12 connector
Cover C ring M12 (bracket)
from becoming loose.
When you attach the C ring, press it
securely between the bracket and cover.

Model Material Applicable connector

XS2Z-18 POM XS2F/H/W

Sputter Protective Cover M12 female screw (thread bracket)

XS2Z-31
XS2Z-31 The Sputter Protective Cover protects the
connector from weld sputter.
Make sure it covers the entire connector.

Pin block (female contact)

Model Material Applicable connector

XS2Z-31 Silicone rubber/black XS2F/XS2H/XS2W

Tools
Torque Wrench
XY2F-0004

Crimp Tool Locator

Tool in open position
XY2F-0002 XY2F-0003

Tool in closed
position

ER AND
ON INSTA R
TI TO LL
O
TATE 90 I

TA
PUSH POS
°

SE TO RO
TE

AI 2
90° TO

1
3 TA
TE

SEL.
RO

NO.
4
N I

ST
AL
7

L
6 5

Use the Crimp Tool to crimp a cable core to the XS2U Selector dial XY2F-0002
Crimping Pin used with the XS2C or XS2G Crimping Locator guide
(Set to 8.) Crimp Tool
Connector.
XY2F-0003 Locator
• The XY2F-0002 Crimp Tool is DMC's AFM8 (M22520/2-
01).
• Mount the XY2F-0003 Locator (sold separately) to the
locator guide of the Crimp Tool with a screw provided with
the XY2F-0003 Locator.

Pin-block Extraction Tool

XY2F-0001
Use this tool to extract a Pin Block from the covers in order to
make wiring changes or corrections after the cover has been
mounted to the pin block for Connector Assemblies (XS2C/
XS2G, soldering/crimping).

89
 XS2
Extraction Procedure
(1) Disconnecting Components • Make sure that the pin block is outside the Tool.
• Disconnect all components on the cap side from the cover.
Tool

Pin block

Pin block Cover Rubber Cable clamp Cap Cover

Guide
bushing Cover

• Press the Tool so that the guides of the Tool are in close
contact. Then pull the pin block straight.

Guide Pin block

(2) Extracting Pin Block
• Insert the claws of the Tool into the four holes of the cover.

Holes
Extracting
direction

Precaution
• The pin block must not be extracted from the same
Connector more than 3 times, otherwise the proper degree
Claws of protection of the pin block or Connector will not be
maintained.

90
 XS2
Assembly Procedure for XS2C/XS2G Connector Assemblies
(1) Connector and Cable External Diameters (3) Wiring (Processing Cable Ends)
• Connectors for 8 ,7 ,6 , 4 , and 3 mm diameter Cables (i.e.,
Soldering Connectors
Cables that are 7 to 8, 6 to 7, 5 to 6, 4 to 5, and 3 to 4 mm
4
in diameter respectively) are available. When assembling a 6
Connector used with a cable, make sure that the external
diameter of the Connector is suited to that of the cable.
• A watertight bushing for 6/7 mm diameter Cable has no
6±0.5 *A
stripe, that for 8/4 mm-diameter Cable has a single stripe,
and that for 3 mm diameter Cable has two stripes. • Strip 10 mm of the Cable sheath and 4 mm of each core.
• Before soldering cores and solder cup pins together, solder-
coat each of them.
(2) Component Insertion • The following conditions are recommended for soldering
Crimping/Soldering Connectors each solder cup pin.
Soldering temperature: 350±5°C
Straight Connectors
Watertight Cable
Soldering period: 3±1 s
Cover bushing clamp Cap • The length marked *A should be 6.5 mm max., otherwise
the proper degree of protection of the connector will not be
maintained.
Crimping Connectors
Right-angle Connectors Crimping
4
10 −0
4

Ring (L-shaped models only) *

Watertight Cable clamp Cap

bushing
Cover
• Strip 14 mm of the Cable sheath and 4 mm of each core.
• Make sure that each core is not damaged and its end
strands are not spread out.
*A ring is not required for Screw-on Connectors. • Mount the XY2F-0003 Locator to XY2F-0002 Crimping
Tool, both of which are sold separately, and set the selector
• As shown in the above illustration, connect the above dial of the Crimping Tool to 8.
components to the Cable with its end processed. • After mounting the crimping pins to the Locator, fully insert
Screw-on Connectors the cores to the crimping pins.
• Squeeze the handle of the Crimp Tool to press-fit the cores
Confirm that you have all of the required parts. to the crimping pins.
Cover Cable clamp (Squeeze the handle firmly until the handle automatically
Watertight
bushing
returns to the release position.)
Cap
Wiring
*2 Pin clamp Press

Ring *1 Watertight bushing

Cable clamp
Cap
Cover 1 to 1.5

•After press-fitting the cores to the pins, insert the pins into the
Insulation caps and insulation tubes are included with pin clamp as shown in the illustration. Then make sure that
5-pole Connectors (XS2C-D5S@ and XS2G-D5S@). the lead colors correspond to the pin clamp numbers that
are identical to the connector pin numbers.
*1.Rings are not required with 7-mm and 8-mm cables.
*2.Insert the waterproof bushing for 7-mm and 8-mm
cables in the direction shown in the diagram.

91
 XS2

Insertion • Bend the cable as shown below, attached the enclosed

Pin Block Pin Clamp insulation cap, and then strip the other cores.
Key groove Key groove

Key XS2C use XS2G use

6±0.5
Insulation cap
• Tentatively insert the pins to the pin block holes so that the
• Connect the cores to pins 1 to 4.
key on the pin block will coincide with the key groove on the
pin clamp. Then insert the cable along with the pin clamp. Connecting Shielded Cables to Five-pole Connectors
Screw-on Connectors • Place the insulation tub on the drain line of the shield and
connect ti to the terminal.
Cable End Processing • Tighten the screw and then check visually to see if there is
• Four-pole Connectors insulation between the cores.
8 Drain line
12 Insulation tube

12±0.5
• Connect the cores to pins 1 to 4.
• Loosen the screws on pins 1 to 4 and insert the cores *When tightening the screws, use the dedicated XW4Z-00B
according to the pin numbers. Screwdriver that matches with the screw-slot dimensions.

• Use the special Screwdriver (XW4Z-00B) * and tighten the XW4Z-00B

Screwdriver
screws securely so that the cores do not pull out (tightening
torque: 0.15 to 0.2 N·m).
(4) Inserting Pin Block
• Five-pole Connectors
• Strip the cable sheath for a total of 15 mm and strip the core Pin Block Cover
(Soldering Model) (Straight Model)
covering for 8 mm for the core to connect to pin 5.
Lock spring
O-ring
8
12 Conductors for
pins 1 to 4

Polarity key Positioning key

8 7 Conductors for (triangle mark) Triangle mark
pin 5

(Crimping Model) (Right-angle Model)

• Connect the core to pin 5 (in the center) first.
• Insert the core from the side of the hold with the tab and
tighten the screw securely (tightening torque: Pins 1 to 4:
0.15 to 0.2 N·m, Pins 5: 0.03 to 0.05 N·m), and then cut off
the excess wire with wire cutters. • Mount the cover to the pin block so that the triangle mark on
Screw the pin block will coincide with the triangle mark on the
Screw
cover.
Special
Screwdriver • If the cover is used for an Right-angle model, the
relationship between the position of the polarity key on the
Special
Screwdriver engaged side and cable connection direction will be
Tab
determined by the direction in which the positioning key is
inserted into the cover, which can be rotated by 90°.
• Fully insert the positioning key until the positioning key is
hidden by the casing.

92
 XS2
Safety Precautions
Pin Block
(Screw-mounting Connectors)
Precautions for Correct Use
Triangle mark Cover
Do not use the product in atmospheres or environments that
exceed product ratings.
Tightening Cap (Connector Assemblies)
1. Do not use pliers to tighten caps, otherwise the caps may
be damaged. Be sure to tighten each cap by hand within a
Cover lock Pin block
torque range between 0.39 and 0.49 N·m.
2. If caps are not tightened securely, the Connectors may not
• Align the triangular marks on the pin block and cover and
maintain their proper degree of protection (i.e., IP67) or the
insert the pin block into the cover.
caps may become loose due to vibration.
• Press them together firmly (0.39 to 0.49 N·m) until the pin
block does not come out of the cover. Connector Connection and Disconnection
• When connecting or disconnecting Connectors, be sure to
(5) Mounting Cap
hold the Connectors by hand.
• After mounting the cover to the pin block and the cover • Do not hold the cable part when disconnecting Connectors.
snaps into place, tighten the cap securely by hand within a • Connectors mating with sockets must be fully inserted into
torque of 0.39 and 0.49 N·m. the sockets. Tighten the thread bracket carefully so that the
Note: If the cap is not tighten securely enough, the degree of protection (IP67) threads will not be damaged.
may not be maintained or vibration may cause the cap to become loose.
Do not tighten the cap with pliers or similar tools; they may damage the
• Fully tighten thread bracket within a torque range between
cap. 0.39 and 0.49 N·m and be sure that the threads of the
opposite parts are hidden by the thread bracket.
• When disconnecting Connectors, be sure to loosen the
thread brackets first. Do not loosen the caps.
• Thread brackets must be loosened in the cutout direction.
A Cap Cutout

• After fully tightening the cap, length A should be Loosen

approximately one of the following according to the cable
external diameter and the Connector model.
Cable external diameter (mm)
Connector
6 mm 5 mm 4 mm 3 mm
For 6-mm-dia. cable 1 0 --- ---
Thread
For 4-mm-dia. cable --- 2 1 --- bracket
For 3-mm-dia. cable --- --- 2 1
Degree of Protection
(6) After Assembly • Do not impose external force continuously on the joints of
pin blocks and covers, otherwise the Connectors may not
• Confirm the insulation between cores after completing
keep its proper degree of protection (i.e., IP67).
assembly.
• The degree of protection of connectors (IP67) is not for a
fully watertight structure. Do not use them underwater.
Recommended Cables • Connectors are of resin mold construction. Do not impose
excessive force on them.
When connecting a commercially available cable to a
connector assembly, use a cable with an outside diameter of Setup
3 to 6 mm and core sizes of 0.18 to 0.75 mm2 for crimping • Do not make any cable bends near the base of the Unit.
connectors and 0.5 mm2 maximum for soldering connectors. • Any bends made must have a minimum radius of 40 mm.

Connector Arrangement
For safety, when constructing a connection system between a
Sensor and panel with a connector, make sure that the
connector plug is on the Sensor side and the connector socket
is on the panel side (i.e., the female pins are located on the
power-supply side).
Sensor Side Connecting Cable Panel Side
(Power-supply Side)

(Plug) (Socket) (Plug) (Socket)

93
 Connector Terminal Boxes

XW3B
Series Includes New Lightweight,
Low-profile Connector Terminal
Boxes for Use Outside of Control
Boxes to Centralize Sensor I/O
Connectors with Reduced Labor and
Greater Environmental Resistance.
• Tough model with a significantly lower profile satisfies
IP67.
• Available for Photoelectric Sensors, Proximity Sensors,
and Limit Switches with Sensor I/O Connectors (M12).
In addition, the rated current has been increased, a ground Refer to Safety Precautions on page 97.

terminal added, and now supports connections to valves

and solenoid.
• Incorporates power and operation indicators.
• Uses a single mounting method regardless of the number
of ports, which ensures easy system expansion.

Ratings and Specifications

4 A/port (signal lines)
Rated current
12 A/box (power lines)
Rated voltage 10 to 30 VDC
Contact resistance 40 MΩ max. (with 100 mA max., 20 mV max.) *1
Insulation resistance 100 MΩ min. (at 500 VDC)
Dielectric strength 500 VAC for 1 min (leakage current: 1 mA max.) *2
Degree of protection IP67 (IEC529)
Cable retention force 98 N/15 s
Insertion tolerance 200 times
Ambient operating
−25 to 70°C
temperature range
* 1.The contact resistance of the Connector.
* 2.The dielectric strength of the Connector.

Compatible Connectors
XS2G Connector Plug Assemblies (crimping, soldering, or screw-on)
XS2W Connectors on cable ends (Sockets or Plugs)
XS2H Connectors on one cable end (Plugs)

Materials and Finish

Item Part name Materials and finish
Lock Brass/nickel plated
Connectors
Contacts Brass/nickel base, 0.4-μm gold plating
Sheath color: gray
Cable Cable
Core size: AWG18/AWG22 *
Case PBT resin (UL94V-0)/light gray
Bushing Rubber
Case
PCB Glass-epoxy board
Seal resin Urethane resin
*The positive power supply, negative power supply, and ground lines are
AWG18. Signal lines are AWG22.

94
 XW3B

XW3B Connector Terminal Boxes

Dimensions (Unit: mm)

XW3B-P45@-@11 (Four Input Ports) Power indicator (green LED)

Operation indicator (red LED)
73
4.5

dia.
e, 4.5
Thre

6.9 dia.

34

12
27 33 54
L 100 10
120

9
9 27 30.5
82

14 dia. Internal connection indication

6.5

20
13.5
9 9

XW3B-P65@-@11 (Six Input Ports) Power indicator (green LED)

Operation indicator (red LED)
73
4.5
.
4.5 dia
Three,

7.7 dia.
56

34

12

27 33 54
L 100 10
120

9
27 27 30.5
100

9 dia. 14 dia. Internal connection indication

6.5

20
13.5
9
4.5 dia.

Power indicator (green LED)

XW3B-P85@-@11 (Eight Input Ports)
Operation indicator (red LED)
73
4.5

dia.
e, 4.5
Thre

8.2 dia.
7 8

56

34

12

27 33 54
L 100 10
120

9
27 27 27 30.5
127

14 dia. 9 dia. Internal connection indication

6.5

20
13.5
9
4.5 dia.

95
 XW3B
Ordering Information

2-wire DC 1 - 4 /
Sensor type and connections 3-wire DC NPN/2-wire 3 - 4 3-wire DC PNP/2-wire DC 1 - 4
without polarity 3 - 4

Actuator connections Actuator connections 1 - 4 — Actuator connections 3 - 4

No. of ports Cable length (m) Model Model Model

4 5 XW3B-P455-G11 XW3B-P452-G11 XW3B-P453-G11
6 5 XW3B-P655-G11 XW3B-P652-G11 XW3B-P653-G11
8 5 XW3B-P855-G11 XW3B-P852-G11 XW3B-P853-G11
Note: Here 1 - 4 and 3 - 4 are connector pin numbers.

Waterproof Cover (Sold Separately)

XS2Z-22
Model Minimum order Materials
XS2Z-22 50 Brass/nickel plated
Note 1. The XW3B/XW3A comes with a dust cover. Use the optional XS2Z-22
Waterproof Cover when an IP67 degree of protection is required.
2. The XS2Z-22 is mounted by screwing it in place

Connection Diagram

XW3B-P@55-@11 for 3-wire DC NPN, XW3B-P@52-@11 for 2-wire DC (with XW3B-P@53-@11 for 3-wire DC PNP,
2-wire DC (without polarity 3 - 4 ), polarity 1 - 4 , without polarity 3 - 4 ) 2-wire DC (with polarity 1 - 4 ), and
and Actuator ( 1 - 4 ) Note: Cannot be used with Proximity Sensors of Actuator ( 3 - 4 )
conventional connector pin with polarity 3 - 4 .

3-WIRE 2-WIRE 3-WIRE

NPN PNP
Ground Ground Ground
Positive power Negative power (Green/ Positive power Negative power (Green/ Positive power Negative power (Green/
supply (Brown) supply (Blue) Yellow) supply (Brown) supply (Blue) Yellow) supply (Brown) supply (Blue) Yellow)
Connector Connector Connector
Power indicator Power indicator Power indicator
pin number pin number pin number
(Green LED) (Green LED) (Green LED)

1 Signal 1 1 1 1
(White)
Signal 1 Signal 1
1 4 5 2 4 5 2 1 4 5 2
(White) (White)
3 Lead Operation indicator 3 3

Lead color (Red LED) Lead

Operation indicator Signal 2 Operation indicator
color 1 2 1 color 1
(Red LED) (Green) (Red LED)
Signal 2 2 4 5 2 4 5 2 Signal 2 2 4 5 2
(Green) (Green)
3 3 3

Signal 3
1 3 1 1
(Yellow)
Signal 3 Signal 3
(Yellow) 3 4 5 2 4 5 2 (Yellow) 3 4 5 2

3 3 3

1 Signal 4 4 1 1
(Gray)
Signal 4 Signal 4
4 4 5 2 4 5 2
(Gray)
4 4 5 2
(Gray)
3 3 3

1 Signal 5 5 1 1
(Pink)
Signal 5 5 4 5 2 4 5 2 Signal 5 5 4 5 2
(Pink) (Pink)
3 3 3

1 Signal 6 6 1 1
(Red)
Signal 6 Signal 6
6 4 5 2 4 5 2 6 4 5 2
(Red) (Red)
3 3 3

1
Signal 7 7 1 1
(Black)
Signal 7 Signal 7
7 4 5 2 4 5 2
(Black)
7 4 5 2
(Black)
3 3 3

Signal 8
1 8 1 1
(Purple)
Signal 8 Signal 8
8 4 5 2 4 5 2
(Purple) 8 4 5 2
(Purple)
3 3 3

Note 1. The above wiring diagrams are for eight-port use.

2. Figures in parentheses indicate lead colors.
3. The expression “white/red” means white and red stripes.
4. Here 1 - 4 and 3 - 4 are pin numbers.
5. Contact numbers 5 through 8 in the above diagrams do not exist on Terminal Boxes with four inputs. The lead colors for signals 1 through 4, power supply, and
ground are the same.
6. Contact numbers 7 and 8 in the above diagrams do not exist on Terminal Boxes with six inputs. The lead colors for signals 1 through 6, power supply, and
ground are the same.

96
 XW3B
Mounting holes (Unit: mm)

Three, M4 or 4.5 dia.

33±0.1

73±0.1
Note: Mounting hole dimensions are always the same regardless of the number of ports.

XW3B Model Compatibility Chart

Cable
No. of
length NPN Sensor specifications 2-wire Sensor specifications PNP Sensor specifications
ports
(m)
4 5 XW3B-P455-G11 XW3B-P452-G11 XW3B-P453-G11
6 5 XW3B-P655-G11 XW3B-P652-G11 XW3B-P653-G11
8 5 XW3B-P855-G11 XW3B-P852-G11 XW3B-P853-G11
Note: Consult your OMRON representative for details on alternatives other than the models shown above.

Safety Precautions

Precautions for Correct Use

Do not use the product in atmospheres or environments that ●Applicable Connectors
exceed product ratings. • Applicable Connectors are the XS2G (assembly type),
●Connector Connection or Disconnection XS2H (monoblock type), and XS2W (monoblock type).
• Before using a Sensor or Limit Switch, check this catalog • After a Connector is engaged, tighten the Connector
and be sure that the Sensor or Limit Switch can be securely with a mounting bracket.
connected. • Be sure to put the XS2Z-22 Waterproof Cover or XS2Z-15
• Be sure to turn OFF the power supplied to the XW3B before Dust Cover on any Connector that is not used.
Connector connection or disconnection.
●Power Supply and Operation Indicators
• Do not touch the engaged side of any Connector with a wet
hand. • When power is supplied, the green power indicator will be
• If a Connector is wet with water, wipe the Connector and be lit. When the Sensors and Actuators are operating, the
sure that the connector is completely dry. corresponding red operation indicators will be lit.
• Be sure that there is no metal plate or power on the • Only DC Sensors and Actuators can be connected to the
engaged side of any Connector. XW3B. Do not connect AC Sensors or Actuators.
• Connector Terminal Boxes are internally wired with 2 or
●Wiring Polarity Mistakes 3 wires. The type is marked on the case.
• Be sure to wire the cable correctly according to the wiring 3-WIRE 3-WIRE 2-WIRE
diagram so that the blue wire will be connected to the NPN PNP

negative power supply terminal and the brown wire will be

connected to the positive power supply terminal.
• If there is any wiring mistake, the load will not operate or the
operation indicator will not light.
• Be sure to connect a load to the signal lines to operate the
Sensor or actuator.

97
 XW3B
Input Device Connections Using Sensor I/O Connectors
Direct Connection Type Connector-Terminal Connection Type Pre-wired Type

XS2W Cable
with connector Proximity Sensor Proximity Sensor
Proximity Sensor
Limit Switch Limit Switch Limit Switch
Photoelectric Sensor Photoelectric Sensor Photoelectric Sensor XS2G Connector
Assembly
(crimping/soldering
type)

XW3B Connector XW3B Connector XW3B Connector

Terminal Box Terminal Box Terminal Box

Input Devices Using Sensor I/O Connectors

Connector
Input devices using Sensor I/O Connectors
Terminal Box
Connector-Terminal E2E-X3D1-M1J-T, E2E-X7D1-M1J-T,
2-wire DC
connection type E2E-X10D1-M1J-T
Proximity Sensor
Direct connection type E2E-X@D1-M1
E2E-X2E1-M1, E2E-X5E1-M1,
3-wire DC
E2E-X10E1-M1
XW3B-P@55-G11 Proximity Sensor Direct connection type
E2E-X5ME1-M1, E2E-X10ME1-M1,
(NPN)
E2E-X18ME1-M1
Connector-Terminal WL@-@DK1EJ@ *1, WL@-@-M1GJ *1,
Limit Switch connection type D4C-@0@@-DK1EJ@ *2
Direct connection type WL@-@K13 *1, D4E-@@10N *2
3-wire DC E2E-X2F1-M1, E2E-X5F1-M1, E2E-X10F1-M1
XW3B-P@53-G11 Proximity Sensor Direct connection type E2E-X5MF1-M1, E2E-X10MF1-M1,
(PNP) E2E-X18MF1-M1
E2E-X3D1-M1GJ, E2E-X3D1-M1J-T,
E2E-X7D1-M1GJ, E2E-X7D1-M1J-T,
E2E-X10D1-M1GJ, E2E-X10D1-M1J-T
Connector-Terminal
E2E-X8MD1-M1GJ, E2E-X14MD1-M1GJ,
connection type
E2E-X20MD1-M1GJ
2-wire DC
E2EQ-X3D1-M1GJ, E2EQ-X7D1-M1GJ,
Proximity Sensor
E2EQ-X10D1-M1GJ
XW3B-P@52-G11 E2E-X3D1-M1G, E2E-X7D1-M1G,
E2E-X10D1-M1G
Direct connection type
E2E-X8MD1-M1G, E2E-X14MD1-M1G,
E2E-X20MD1-M1G
Connector-Terminal WL@-@DK1EJ@ *1, WL@-@-M1GJ *1,
connection type D4C-@0@@-DK1EJ@ *2
Limit Switch
WL@-@K13 *1, D4E-@@10N *2
Direct connection type
D4CC-@@@@ *2
Note: Use the XS2G Connector assembly in combination with a pre-wired input device.
*1. Any of these models is available provided that only its SPST-NO contacts are used.
*2. Any of these models is available provided that it uses an NO connection.

98
 XW3B
Attaching the XS2G Connector to Pre-wired Input Device

Input devices and connector pin number

Connector 3-wire DC (NPN) 2-wire DC 2-wire DC 2-wire DC 3-wire DC (PNP)
Terminal Box 1: +, 3: −, (with polarity) (with polarity) (with no polarity) Limit Switch 1: +, 3: −,
4: output 1: +, 4: − 3: −, 4: + 3, 4 4: output
XW3B-P@55-G11 Yes No Yes Yes Yes No
XW3B-P@53-G11 No Yes No No No Yes
XW3B-P@52-G11 No Yes No Yes Yes No

Connector Terminal Boxes for Input Devices with Sensor I/O Connectors
Input device Connector
Type Connection method Model Terminal Box
E2E-X@D1-M1J-T XW3B-P@55-G11
E2E-X@D1-M1GJ
Connector-Terminal connection
E2E-X@D1-M1J-T
type
E2E-X@MD1-M1GJ
2-wire DC XW3B-P@52-G11
E2EQ-X@D1-M1GJ
Proximity E2E-X@D1-M1G
Sensors E2E-X@MD1-M1G
E2E-X@D1-M1
Direct connection type E2E-X@E1-M1 XW3B-P@55-G11
NPN
3-wire E2E-X@ME1-M1
DC E2E-X@F1-M1
PNP XW3B-P@53-G11
E2E-X@MF1-M1
WL@-@DK1EJ@ *1
Connector-Terminal connection
WL@-@-M1J *1
type XW3B-P@52-G11
D4C-@0@@-DK1EJ@ *2
Limit Switches XW3B-P@55-G11
WL@-@K13 *1
Direct connection type D4E-@@10N *2
D4CC-@@@@ *2 XW3B-P@52-G11
*1. Any of these models is available provided that only its SPST-NO contacts are used.
*2. Any of these models is available provided that it uses an NO connection.

For components that are compatible with Sensor I/O Connectors, refer to the above model numbers.

99
 MEMO

100
 Round Water-resistant Connectors (M8/S8)

XS3
Small Round Water-resistive
Connectors
• Water-resistive, compact connector meets IP67 requirements.
• Conventional M8 screw-mounting models are available along with
S8 snap-in models that connect and disconnect with one touch.
• Ideal for a wide variety of FA and OA applications.
• Connectors on both cable ends require no harness work.
• Some new M8 models with 3 or 5 poles.
Refer to Safety Precautions on page 121.

Ratings and Specifications

Item Model XS3F/H/W/P/M XS3F-M52@-5@@-A XS3M-M524-1@ XS3R
Rated current 1 ADC 3 ADC 1 ADC
Rated voltage 125 VDC *2 30 VDC 125 VDC
Contact resistance 40 mΩ max. 60 mΩ max.
(20 mVDC max.,
(connector) (20 mV max., 100 mA max.) 100 mA max.)
Insulation resistance 1,000 MΩ min. (at 500 VDC)
Dielectric strength 1,000 VAC for 1 min 650 VAC for 1 min 1,000 VAC for 1 min
(connector) (leakage current: 1 mA max.) (leakage current: 1 mA max.) (leakage current: 1 mA max.)
Degree of protection IP67 (IEC60529)
Insertion tolerance 200 times
Cable tensile strength *1 49 N/15 s
Ambient operating −25 to 70°C −25 to 85°C −25 to 70°C
temperature range
Ambient humidity range 20 to 85%RH
*1. Models with cable only
*2. Except 5poles

Materials and Finish

Connector
Type M8 S8
Item Model XS3F/H/W/R XS3P/M * XS3M-M524-1@ XS3F/W (Socket side) XS3H/W (Plug side) XS3P
Contact block PBT resin (UL94 V-0) light gray or black
Phosphor bronze/ Phosphor bronze/
Brass/nickel base, Brass/nickel base, 0.4-μm gold
Contacts nickel base, 0.4- nickel base, 0.4-
0.4-mm gold plating plating
μm gold plating μm gold plating
Thread bracket Brass/nickel plating or SUS316L — Brass/nickel plating —
Body — Brass/nickel plating Nickel-plated zinc alloy —
Shell — TPEE
C-Ring — Phosphor bronze/tin plating —
Grounding fixture — Phosphor bronze/tin plating —
Nut — Brass/nickel plating — Brass/nickel plating
Soft PBT resin
Cover — TPEE —
(UL94 V-0)
O-ring Rubber
*Except 5poles
Note: The XS3M is for both M8 and S8.

Cables Pin Arrangement (Engaged Side)

Item Poles 3 poles 4 poles 5 poles
Standard 4 mm dia, 4.7 mm dia,
Item Poles 3 poles 4 poles 5 poles
AWG24 (0.2 mm2) AWG24 (0.2 mm2)
cable
Structure: 0.12 mm/18 Structure: 0.16 mm/11 Male 4
2 4 2 4
4 mm dia, 1 3
Robot ca- (plug) 1 3
AWG24 (0.2 mm2) — contacts 1 3
ble 5
Structure: 0.08 mm/40 DC
Note: Only the XS3F (socket) is available with 5 pins. Female 4
4 2 4 2
3 1
(socket) 3 1
3 1
contacts 5

101
 XS3
Wiring System Configuration
Sensor End Relay Cable
Using Sensors with Connectors
Proximity Sensor Connector with Cable
(M8 Connector Models)
XS3W (screw-mounting models)
E2E

Proximity Sensor XS3W (snap-in models)

(Pre-wired Connector Models)

E2E

Fiber Amplifier
(Connector models)

E3X

Multiple XS3W (screw-mounting and snap-in models)

can be used to extend the cable.

Photoelectric Sensor
Connector with Cable
(Connector models)
XS3F (screw-mounting models)
E3Z

Making Sensors with Cables (Sensor Manufacturers)

XS3F (snap-in models)
Connector with Cable XS3H
(screw-mounting models)

XS3H (snap-in models)

Connectors with Cable

Used to enable connectors (direct connection types) to be XS3W (M8 to M12 Smartclick Conversion Cable)
integrated with the Sensor body.
Sensor-embedded Connector

XS3M (Embedded Model)

102
 XS3
( indicates mating connectors, and indicates wiring connections.)

PCB Type ■ Personal Computer

■ PT (Programmable Terminal)

Terminal Box Connector

XS3P

Y-Joint
XS3R

Host Link Cable

Used to enable using connectors for XW2Z
terminal boxes.

Used to wire two Sensors to a single

cable.

Connector-Terminal Block
Conversion Units
XW2R (PLC, General-purpose devices) Connecting Cable
XW2D (slim model)
XW2C (with power supply common terminal) XW2Z
XW2B (general-purpose model) Programmable
XW2F (with screwless clamp terminals)
Controller
Crimp
terminal
wiring

Terminal Block
(Commercially Available)

M12 Connector with Cable

XS5F (Smartclick)

XS2F (screw-on)

Refer to your OMRON website for details on M12 Connectors with Cables.

103
 XS3

XS3W Connectors with Cables, Connectors on Both Ends (Socket/Plug)

● M8 Screw-mounting Connectors with Vibration-proof Robot Cable XS3W-M@2@-@@@-R

Dimensions (Unit: mm)

Straight/Straight Connectors Straight/Right-angle Connectors

M8 × 1.0 10 dia.
M8 × 1.0
4 dia.
Socket Plug
4 dia.
9 dia. 10 dia. 21.1

9 dia.
31.4 32
L
31.4 23.1
L

Right-angle/Right-angle Connectors Right-angle/Straight Connectors

9 dia. 9 dia.
10 dia.
M8 × 1.0

M8 × 1.0
4 dia. 4 dia.
20.5 21.1 20.5

10 dia.

23.1 23.1 23.1 32

L L

● S8 Snap-in Connectors with Vibration-proof Robot Cable XS3W-S42@-4@@-R

Dimensions (Unit: mm)

Straight/Straight Connectors Straight/Right-angle Connectors 8.2 dia.

4 dia.
Socket Plug
4 dia.

8.2 dia. 8.2 dia. 19.8

8.2 dia.
30.7 30.7
L
30.7 23.1
L

Right-angle/Right-angle Connectors Right-angle/Straight Connectors

8.2 dia. 8.2 dia. 8.2 dia.

4 dia.
4 dia.
19.8 19.8 19.8

8.2 dia.

23.1 23.1 23.1 30.7

L L

104
 XS3
Model Number Legend
Use this model number legend to identify products from their model number. When ordering, use a model number from the table
in Ordering Information.

XS3W-@@2@-@@@-R
1 2 3 4 5 6

1. Fastening Method 3. Cable Connection Direction 4. Connections 5. Cable Length

M: M8 1: Straight/ Pin No. 01: 1 m
S: S8 Straight ➀ ➂ ➃ 02: 2 m
2: Right-angle/ 3: Brown Blue Black 05: 5 m
Right-angle Pin No.
2. Connector Poles 3: Straight (socket)/ ➀ ➁ ➂ ➃
3: 3 poles Right-angle (plug) 4: Brown White Blue Black 6. Cable Specifications
4: 4 poles 4: Right-angle (socket)/ R: Vibration-proof
Straight (plug) robot cable

Wiring Diagram/Engaged Side Mating Connectors

3 poles Item Socket side Plug side
Pin No. Cable lead colors
XS3F (M8)
XS3M (M8/S8)
4 1 1 Brown 4 XS3W (M8) XS3W (M8)
3 1 1 3 XS3H (M8)
3 3 Blue XS3P (M8)
4 4 Black
XS3F (S8)
XS3M (M8/S8)
Socket Plug XS3W (S8) XS3W (S8)
XS3H (M8)
4 poles XS3P (S8)
Pin No. Cable lead colors Note 1. Cables can be extended with more than one XS3W.
Brown
2. M8 screw models and S8 snap-in models cannot be connected to each
1 1
4 2 2 4 other.
2 2 White
3 1 3 3 Blue 1 3
4 4 Black

Socket Plug

Ordering Information
M8 Screw-mounting Connectors
No. of cable cores Cable connection direction Cable length L (m) Model
1 XS3W-M321-301-R
3 Straight/Straight 2 XS3W-M321-302-R
5 XS3W-M321-305-R
1 XS3W-M421-401-R
Straight/Straight 2 XS3W-M421-402-R
5 XS3W-M421-405-R
2 XS3W-M422-402-R
Right-angle/Right-angle
4 5 XS3W-M422-405-R
Straight (socket)/ 2 XS3W-M423-402-R
Right-angle (plug) 5 XS3W-M423-405-R
Right-angle (socket)/ 2 XS3W-M424-402-R
Straight (plug) 5 XS3W-M424-405-R

S8 Snap-in Connectors
No. of cable cores Cable connection direction Cable length L (m) Model
1 XS3W-S421-401-R
Straight/Straight 2 XS3W-S421-402-R
5 XS3W-S421-405-R
2 XS3W-S422-402-R
Right-angle/Right-angle
4 5 XS3W-S422-405-R
Straight (socket)/ 2 XS3W-S423-402-R
Right-angle (plug) 5 XS3W-S423-405-R
Right-angle (socket)/ 2 XS3W-S424-402-R
Straight (plug) 5 XS3W-S424-405-R

105
 XS3

XS3W Connectors with Cables, Connectors on Both Ends (M8 Socket/M12 Plug or M8 Plug/M12 Socket)
● Screw-on Connectors (M8 to M12) XS3W-M@2@-@C2-A

Dimensions (Unit: mm)

XS3W-M32C-3C2-A, XS3W-M42C-4C2-A
200
44.7 31.4
(3 cores)
2 1

1 3
14.9 dia. 9 dia.
4
3 4
4 dia.
Plug Socket M8×1.0
M12×1.0
(4 cores)

1 3

2 4

M8×1.0

XS3W-M32D-3C2-A, XS3W-M42D-4C2-A

200
40.7 32
1 2 (3 cores)

3 1
14.9 dia. 10 dia.

4
4 3 4 dia.
Socket Plug M8×1.0
M12×1.0
(4 cores)

3 1

4 2

M8×1.0

Note: For 3-core, M12 connectors, pin 2 is not connected internally.

For the M12 connectors, one-touch (Smartclick) connectors

that are compatible with previous screw-on M12 connectors
are used. Refer to your OMRON website for details.

XS5 Series

Clic
k!

Insert fully.
Rotate 1/8 turn.
One-touch Connection

is a registered trademark of the OMRON Corporation.

106
 XS3
Model Number Legend
Use this model number legend to identify products from their model number. When ordering, use a model number from the table
in Ordering Information.

XS3W-M@2@-@C2-A
1 2 3 4 5 6

1. Fastening Method 3. Cable Connection Direction 4. Connections 5. Cable Length

M: M8 C: M8 (screw-on) socket: Pin No. C2: 20 cm
Straight, M12 (Smartclick) ➀ ➂ ➃
plug: Straight 3: Brown Blue Black
2. Connector Poles D: M8 (screw-on) plug: Pin No. 6. Cable Specifications
3: 3 poles Straight, M12 (Smartclick) ➀ ➁ ➂ ➃ A: Standard cable
4: 4 poles socket: Straight 4: Brown White Blue Black

Wiring Diagram
3 poles 4 poles

Cable lead Cable lead

Pin No. colors Pin No. colors

1 1 Brown 1 1 Brown
2 2 White
3 3 Blue
3 3 Blue
4 4 Black
4 4 Black

Ordering Information
No. of cable cores Connectors Cable length L (m) Model
M8 socket/M12 plug XS3W-M32C-3C2-A
3
M8 plug/M12 socket XS3W-M32D-3C2-A
0.2
M8 socket/M12 plug XS3W-M42C-4C2-A
4
M8 plug/M12 socket XS3W-M42D-4C2-A

107
 XS3

XS3F Sockets on One Cable End

● M8 3 pin Screw-on Cables with Vibration-proof Robot Cable/Standard Cable XS3F-M32@-3@@-@

Dimensions (Unit: mm)

Straight Connectors M8 × 1.0

4 dia.
4

9 dia.
3 1
1.75
21.5 30 5
3.5 50
31.4
L

L 50
Right-angle Connectors 23.1 4 dia. 30 5

20.5

9 dia.
1
4
3.5 Wiring Diagram
3 Pin No.
1.75 Cable lead colors
M8 × 1.0
1 Brown
3 Blue
4 Black

● M8 4 pin Screw-on Cables with Vibration-proof Robot Cable/Standard Cable XS3F-@42@-4@@-@

Dimensions (Unit: mm)

Straight Connectors
2.15 M8 × 1.0
12.9 4 dia.
4 2
9 dia.
1.95 0.5 3 1
21.5 30 5
3.4 50
31.4
L

Right-angle Connectors
L 50
23.1 30 5

20.5
4 dia.

9 dia.
1
2 Wiring Diagram
3.4
4 Pin No.
Cable lead colors
2.15 3
0.5 1 Brown
M8 × 1.0 1.95 2 White
3 Blue
4 Black

108
 XS3
● M8 5 pin Screw-on Cables with Standard Cable XS3F-M52@-5@@-A

Dimensions (Unit: mm)

Straight Connectors
1.95 M8 × 1.0 4.7 dia.
1.45 2
4
1 9 dia.

1.35 3 5 0.35
21.5 30 5
3.4 50
31.4 L

24.9 L
4.7 dia.

Right-angle Connectors 20.5

30 5
50

9 dia.
M8 × 1.0
0.35 Wiring Diagram
2 1
5 Pin No.
3.4 Cable lead colors
4 1 Brown
1.95 3 2 White
1.35 3 Blue
4 Black
1.45 5 Gray

● S8 Snap-in Connectors with Vibration-proof Robot Cable XS3F-S42@-4@@-R

Dimensions (Unit: mm)

Straight Connectors
2.15
13.9 4 dia.
4 2
8.2 dia.
1.95 0.5 3 1
21.1 30 5
3.4 50
30.7
L

Right-angle Connectors L 50
23.1 30 5

19.8
4 dia.

Wiring Diagram
8.2 dia.
2 1 Pin No.
3.4
Cable lead colors
4 3 1 Brown
2.15 2 White
0.5 3 Blue
1.95 4 Black

109
 XS3
Model Number Legend
Use this model number legend to identify products from their model number. When ordering, use a model number from the table
in Ordering Information.

XS3F-@@2@-@@@-@
1 2 3 4 5 6

1. Fastening Method 3. Cable Connection Direction 5. Cable Length

M: M8 1: Straight 01: 1 m
S: S8 2: Right-angle 02: 2 m
E: M8 05: 5 m
SUS316L Lock 4. Connections 10: 10 m
Pin No.
2. Connector Poles ➀ ➂ ➃ 6. Cable Specifications
3: 3 poles 3: Brown Blue Black A: Standard cable
4: 4 poles Pin No. R: Vibration-proof robot cable
5: 5 poles ➀ ➁ ➂ ➃
4: Brown White Blue Black
Pin No.
➀ ➁ ➂ ➃ ➄
5: Brown White Blue Black Gray

Mating Connectors
Item Model
XS3F(M8) XS3M (M8/S8), XS3H (M8), XS3W (M8)
XS3F(S8) XS3M (M8/S8), XS3H (M8), XS3W (M8)
Note: M8 screw models and S8 snap-in models cannot be connected to each other.

110
 XS3
Ordering Information
M8 Screw-on Cables
No. of cable cores Item Cable connection direction Cable length L (m) Model
2 XS3F-M321-302-A
Straight
5 XS3F-M321-305-A
Standard cable
2 XS3F-M322-302-A
Right-angle
5 XS3F-M322-305-A
3
2 XS3F-M321-302-R
Straight
5 XS3F-M321-305-R
Vibration-proof robot cable
2 XS3F-M322-302-R
Right-angle
5 XS3F-M322-305-R
2 XS3F-M421-402-A
Straight
5 XS3F-M421-405-A
Standard cable
2 XS3F-M422-402-A
Right-angle
5 XS3F-M422-405-A
1 XS3F-M421-401-R
Straight 2 XS3F-M421-402-R
5 XS3F-M421-405-R
4 Vibration-proof robot cable
1 XS3F-M422-401-R
Right-angle 2 XS3F-M422-402-R
5 XS3F-M422-405-R
2 XS3F-E421-402-A
Straight
5 XS3F-E421-405-A
Standard SUS316L cable lock
2 XS3F-E422-402-A
Right-angle
5 XS3F-E422-405-A
2 XS3F-M521-502-A
Straight 5 XS3F-M521-505-A
10 XS3F-M521-510-A
5 Standard cable
2 XS3F-M522-502-A
Right-angle 5 XS3F-M522-505-A
10 XS3F-M522-510-A

S8 Snap-in Connectors
No. of cable cores Item Cable connection direction Cable length L (m) Model
1 XS3F-S421-401-R
Straight 2 XS3F-S421-402-R
5 XS3F-S421-405-R
4 Vibration-proof robot cable
1 XS3F-S422-401-R
Right-angle 2 XS3F-S422-402-R
5 XS3F-S422-405-R

111
 XS3

XS3H Plugs on One Cable End

● M8 3 pin Screw-on Connectors with Vibration-proof Robot Cable XS3H-M321-3@@-R

Dimensions (Unit: mm)

Straight Connectors M8 × 1.0

4 dia.
4

10 dia.
1 3
1.75
21.5 30 5
3.5 50
32
L

Wiring Diagram
Pin No.
Cable lead colors
1 Brown
3 Blue
4 Black

● M8 4 pin Screw-on Connectors with Vibration-proof Robot Cable XS3H-M42@-4@@-R

Dimensions (Unit: mm)

Straight Connectors Four, 1 dia. 2.15

M8 × 1.0 12.9 4 dia.
2 4
10 dia.
1.95 0.5 1 3
21.5 30 5
3.4 50
32
L

Right-angle Connectors L 50
23.1 30 5

20.1
4 dia.

M8 × 1.0

Four, 1 dia. 10 dia. Wiring Diagram

4 3
Pin No.
3.4 Cable lead colors

2.15 2 1 1 Brown
0.5
2 White
3 Blue
1.95 4 Black

112
 XS3
● S8 4 pin Snap-in Connectors with Vibration-proof Robot Cable XS3H-S42@-4@@-R

Dimensions (Unit: mm)

Straight Connectors Four, 1 dia. 2.15

13.9 4 dia.
2 4
8.2 dia.
1.95 0.5 1 3
21.1 30 5
3.4 50
30.7
L

L 50
Right-angle Connectors 23.1 30 5

19.8
4 dia.

Four, 1 dia. 8.2 dia.

4 3
3.4

2.15 2 1
0.5
1.95

113
 XS3
Model Number Legend
Use this model number legend to identify products from their model number. When ordering, use a model number from the table
in Ordering Information.

XS3H-@@2@-@@@-R
1 2 3 4 5 6

1. Fastening Method 3. Cable Connection Direction 5. Cable Length

M: M8 1: Straight C3: 0.3 m
S: S8 2: Right-angle 01: 1 m

2. Connector Poles 4. Connections 6. Cable Specifications

3: 3 poles Pin No. R: Vibration-proof robot cable
4: 4 poles ➀ ➂ ➃
3: Brown Blue Black
Pin No.
➀ ➁ ➂ ➃
4: Brown White Blue Black

Mating Connectors
Item Model
XS3H(M8) XS3F (M8), XS3W (M8), XS3P (M8)
XS3H(S8) XS3F (S8), XS3W (S8), XS3P (S8)
Note: M8 screw models and S8 snap-in models cannot be connected to each other.

Ordering Information
M8 Screw-on Connectors
No. of cable cores Cable connection direction Cable length L (m) Model
0.3 XS3H-M321-3C3-R
3 Straight
1 XS3H-M321-301-R
0.3 XS3H-M421-4C3-R
Straight
1 XS3H-M421-401-R
4
0.3 XS3H-M422-4C3-R
Right-angle
1 XS3H-M422-401-R

S8 Snap-in Connectors
No. of cable cores Cable connection direction Cable length L (m) Model
0.3 XS3H-S421-4C3-R
Straight
1 XS3H-S421-401-R
4
0.3 XS3H-S422-4C3-R
Right-angle
1 XS3H-S422-401-R

114
 XS3

XS3P Panel-mounting Sockets for Terminal Boxes

● M8 Screw-mounting Sockets with DIP Pins XS3P-M421-1
● M8 Screw-mounting Sockets with Solder Cup Pins XS3P-M421-2
● M8 Screw-mounting Sockets with Solder Cup Pins XS3P-M422-2

Dimensions (Unit: mm)

XS3P-M421-1 (DIP Pins) XS3P-M421-2 (Solder Cup Pins)

Front lock or rear lock Front lock or rear lock
24.9 24.3
1.8 1.8
Four, 1 dia. 16 7.2 12.5 16 7.2 12.5
2.15 2.15
7.2 2.15 7.2 2.15

1.95 1.95 1.95 1.2 dia. 1.95

0.5 0.5 0.5 0.5

Solder cup
hole
18 dia. M12 × 1.0 M12 × 1.0 18 dia. 0.8 dia. × 2.5 M12 × 1.0
3.4 2.5 1.5 3.4 M8 × 1.0 3.4 1.5 3.4 M8 × 1.0
M12 × 1.0 2.5
9.4 M12 × 1.0 nut Rubber 9.7 9.4 Rubber 9.7
M12 × 1.0 nut
bushing bushing

XS3P-M422-2 (Solder Cup Pins), Rear Lock Slim Models

10 13.2 (0.3) 2.15
7 2 6
1.95

11.5 dia.

M8 × 0.5 M8 × 1.0
Rubber
M8 × 0.5 nut 2 bushing 3.4
10

● S8 Snap-in Sockets with DIP Pins XS3P-S421-1

● S8 Snap-in Sockets with Solder Cup Pins XS3P-S421-2

Dimensions (Unit: mm)

XS3P-S421-1 (DIP Pins) XS3P-S421-2 (Solder Cup Pins)

Front lock or rear lock Front lock or rear lock
24.9 24.3
1.8 1.8
Four, 1 dia. 16 7.2 12.5 16 7.2 12.5
2.15 2.15
7.2 2.15 7.2 2.15

1.95 1.95 1.95 1.2 dia. 1.95

0.5 0.5 0.5 0.5

Solder cap
hole
18 dia. M12 × 1.0 M12 × 1.0 18 dia. 0.8 dia. × 2.5 M12 × 1.0
3.4 2.5 1.5 3.4 3.4 1.5 3.4
M12 × 1.0 2.5
9.4 M12 × 1.0 nut Rubber 9.5 9.4 Rubber 9.5
M12 × 1.0 nut
bushing bushing

115
 XS3
Mounting Dimensions for XS3P Screw-on Models and Snap-in Models (Unit: mm)

Panel Cutouts PCB-mounting Dimensions Panel-mounting

XS3P-@421-@ XS3P-M422-2 Dimensions Front Lock
+0.2
9.8 0 24 min. Rear Lock Panel
Land 2.15
Panel
+0.2
8.2 0
0.5 1.95
Four, 1.2 dia. 3.4
+0.2
12 0 dia. 24 min.
+0.2
7.20
Note: The panel thickness is 1 to 3 mm. Note: The panel thickness is 2.4 mm
maximum. Rubber Nut
Rubber bushing
Nut bushing

Mating Connectors
Item Model
XS3P(M8) XS3H (M8), XS3W (M8)
XS3P(S8) XS3H (S8), XS3W (S8)
Note: M8 screw models and S8 snap-in models cannot be connected to each other.

Ordering Information
Connection method Panel mounting Pin shape Applicable wires Model Minimum order
DIP pins --- XS3P-M421-1
Front lock or rear lock
M8 screw-mounting Solder cup pins AWG24 max. XS3P-M421-2
Rear lock Solder cup pins AWG24 max. XS3P-M422-2 50
DIP pins --- XS3P-S421-1
S8 snap-in Front lock or rear lock
Solder cup pins AWG24 max. XS3P-S421-2
Note: Orders are accepted in multiples of the minimum order.

Safety Precautions
In addition to the following information, also refer to Safety Precautions on page 121
Precautions for Correct Use
Panel Mounting
• When mounting XS3P Panel-mounting Connectors to panels, refer to Panel-mounting Dimensions and provide rubber bushings
and nuts for the Connectors. Apply a tightening torque of between 0.4 and 0.6 N·m to mount the Connectors.

116
 XS3

XS3M Sensor Embedded Plugs

● Embedded Plugs with Screw Threads and DIP Pins XS3M-K421-1
● Embedded Plugs with Screw Threads and Solder Cup Pins XS3M-K421-2

Dimensions (Unit: mm)

XS3M-K421-1
Embedded Model with DIP Pins
Mounting Dimensions
M8 × 1.0 0.4 2.15 Four, 1 dia.
Four, 1 dia. 1 dia.
4 2 2 4

6.5 dia. 5.8±0.2 dia. 5.8 dia. 6.5 dia. 6.9 dia. +0.05
5.8 0 dia.

3 1 1 3 0.5 1.95
5.6 dia. 2 Resin
3.4
3 3 filled
7.2 (min)
6.75
3.6 10.3
XS3M-K421-2
Embedded Model with Solder Cup Pins
M8 × 1.0 0.4 2.15 Four, 1 dia. Mounting Dimensions
Four, 1 dia. 1 dia.
4 2 2 4

6.5 dia. 5.8±0.2 dia. 5.8 dia. 6.5 dia. 6.9 dia. +0.05
5.8 0 dia.

3 1 1 3 0.5 1.95
5.6 dia. 2 Resin
Solder cup hole 3.4 filled
3 3
0.7 dia. × 1.7 5.2 (min)
6.75
1.7 10.3

Mating Connectors
Item Model
XS3M XS3F (M8/S8), XS3W (M8/S8)
Note: The plug can be connected to both M8 screw and S8 snap-in models.

Ordering Information
Connection method Pin shape Applicable wires Model Minimum order
DIP pins --- XS3M-K421-1
Embedded model 200
Solder cup pins AWG26 max. XS3M-K421-2
Note: Orders are accepted in multiples of the minimum order.

117
 XS3

XS3M Panel-mounting Plugs

● Front lock DIP pins (5 pins) XS3M-M524-@@
Dimensions (Unit: mm)

XS3M-M524-10
Front Lock with DIP Pins 4.5 mm (for Either Round Holes or Solder Cups), Without Shield Pin
Panel Cutout PCB-mounting Dimensions
+0.1 +0.1 3.4 Five, 1.7 dia. lands
8.2 mm dia. 0 7.1 0
1.95
Five, 1.2 dia.
2-1.45 2 4

1.35 1 3
O-ring on panel side*
2-0.35 5

Note: The panel thickness is Note: The panel thickness is 2.4 mm Pin Numbers
0.8 to 2 mm. maximum.
3.4 O-ring on panel side* 3.4

1.95 M8 × 1.0 12 1.95

11.9 dia.
1.45 1.45
5-1 dia.
*The O-ring on the panel side maintains
a waterproof structure (IP67) between
0.35 1.35 0.35 the panel and Connector.
1.35
SW7
5-4.5 SW11
6 min. 7.05
SW10
(2.5)
Panel location (example for t = 2.0)
XS3M-M524-11
Front Lock with DIP Pins 4.5 mm (for Either Round Holes or Solder Cups), With Shield Pin
Panel Cutout PCB-mounting Dimensions
10.4

3.4
1.95
+0.1 +0.1 Two, 1.2 lands
8.2 mm dia. 0 7.1 0 Five, 1.7 dia. lands
2-0.7
Five, 1.2 dia. 4-R0.6
2-1.45 4-R0.35 2 4

Two, 3.8
lands
1.35 1 3
O-ring on panel side* Two, 3.3
2-0.35 lands 5

Note: The panel thickness is Note: The panel thickness is 2.4 mm Pin Numbers
0.8 to 2 mm. maximum.
10.4
3.4 O-ring on panel side* 3.4
M8 × 1.0 5-4.5
1.95 12 11.9 dia. 1.95

1.45 5-1 dia. 1.45

2-2.6
*The O-ring on the panel side maintains
0.35 1.35 0.35
1.35 a waterproof structure (IP67) between
SW7
2-4.5 SW11
the panel and Connector.
6 min. 7.05
SW10
(2.5)
Panel location (example for t = 2.0)

Mating Connectors
Item Model
XS3M-M524-1@ XS3F-M52@-5@@-A

Ordering Information
Lock method Pin shape Shield pin Applicable wires Model

DIP pins 4.5 mm No XS3M-M524-10

Front lock AWG26 max.
(for either round holes or solder cups) Yes XS3M-M524-11
Note: Orders are accepted in multiples of the minimum order.

118
 XS3
Safety Precautions
In addition to the following information, also refer to Safety Precautions on page 121
Precautions for Correct Use
XS3M-M524-@@ Mating
To mate the Connectors, align the mating marks on the Plug and Socket (see following figure), insert the Connectors completely,
and tighten the lock nut, being careful not to damage the threads.

Plug

Mating marks

Socket

XS3M-M524-@@ Panel Mounting

After you mount the Connector to the panel, attach the nut and tighten it to a suitable torque (0.4 N·m).

XS3 M8/S8 Connector Cover

Dust Cover
XS3Z-13 XS3Z-15
XS3Z-13 M8 Plug
XS3Z-15 M8 Socket

S8 Socket
The Dust Cover is for dust prevention and
does not ensure IP67. When mounting the
Dust Cover to a Connector, be sure to press
the Dust Cover onto the Connector until the
S8 Plug Connector is fully inserted into the Dust
Cover.

Suitable connector
Model Material
Model Mounting portion
XS3H/XS3W/XS3R M8 plug
XS3F/XS3W S8 socket
XS3Z-13
PVC resin/red XS3H/XS3W S8 plug
XS3M M8/S8 plug
XS3Z-15 XS3F/XS3W/XS3R M8 socket

119
 XS3

XS3R Y-Joint Plug/Socket Connectors

● Screw-on Models (M8) With Standard Cable: XS3R-M426-1@@@-A
Without Cable: XS3R-M426-@

Dimensions (Unit: mm)

XS3R-M426-1@@1-A
Connectors on Both Cable Ends (Y-Joint Plug/Socket)
Socket 16.4
1
.
10.5
dia
2 4
M8 × 1.0 CN2
3.5
4 dia. Plug
9 dia. 3 1
2

10 dia.
4 3
23

2 1 12.5 5.6 dia.

CN0
9 dia.
1

4
32 4 2
3
CN1 L M8 × 1.0
XS3R-
M426-1@@0-A
Socket 16.4
1
.

10.5
dia

2 4
3.5

M8 × 1.0 CN2
4 dia.
9 dia.
2

4 3
23

2 1 12.5
5.6 dia.

9 dia.
1

4 30 5
3
CN1 L 50

XS3R-M426-@
Connector on Both Ends (Y-Joint Plug/Socket) without Cable
16.4
1 Socket
.
dia

10.5 4
2 M8 × 1.0
3.5

CN2 Plug
1 2
9 dia.
2

4 3
23

2 1 12.5 10 dia. CN0

9 dia.
1

4 3 4
3
CN1 37.2 M8 × 1.0

Wiring Diagram
XS3R-M426-1@@1-A XS3R-M426-1@@0-A XS3R-M426-1 XS3R-M426-5
1 1 1 1
2 2 2 2
CN2 3 CN2 3
CN2 3
CN2 3
4 4 4 Black 4 4 4 4
3 Blue 3 3
2
CN0 2
CN0 2
CN0
White
1 1 1 Brown 1 1 1 1
2 2 2 2
CN1 CN1 Lead CN1 CN1
3 3 3 3
color
4 4 4 4

Mating Connectors Ordering Information

Item Model For M8 Connectors
XS3F(M8) Cable length Minimum
Cable Connector Model
XS3H(M8) L (m) order
XS3R(M8) 0.5 XS3R-M426-1C51-A
XS3W(M8)
XS3P(M8) Connectors on both 1 XS3R-M426-1011-A
With cable ends 2 XS3R-M426-1021-A
5
cable 3 XS3R-M426-1031-A
Connector on one 2 XS3R-M426-1020-A
cable end 5 XS3R-M426-1050-A
Without Connectors on both XS3R-M426-1
--- 10
cable cable ends XS3R-M426-5

120
 XS3
Safety Precautions

Precautions for Correct Use

Do not use the product in atmospheres or environments that
exceed product ratings.

Connections Degree of Protection

• The XS3 and XS2 Sensor I/O Connectors cannot be • Do not impose external force continuously on the joints of
connected to each other. pin blocks and covers, otherwise the Connectors may not
• You cannot mate Connectors that have a different number keep its proper degree of protection (i.e., IP67).
of poles. • Connectors are not fully watertight. Do not use them
• When using Sensors with Connectors or Limit Switches, underwater.
use the Sensor I/O Connectors specified in the catalog. • The Connectors are not oil-resistant. Do not use them
• Do not connect M8 screw models and S8 snap-in models where they would be subject to oil.
together, otherwise the proper degree of protection of the • If Connectors are used in places with vibration or shock,
Connectors will not be maintained. secure the engaged side of each Connector, otherwise the
Connectors may be disconnected or fail to maintain their
Connector Connection and Disconnection
proper degree of protection.
• Before connecting or disconnecting Connectors, make sure • Connectors are of resin mold construction. Do not impose
that no power is being supplied to the Connectors. excessive force on them.
• When connecting or disconnecting Connectors, be sure to
hold the Connectors by hand. Do not disconnect the Storage
Connectors by pulling the cable. Do not store Connectors for long periods of time in the
• Do not touch the engagement side of any Connector with following locations
wet hands. If there is any water on the Connector or near • Locations subject to dust or high humidity
the Connector, be sure to wipe off the water before • Locations subject to ammonia gas or sulfide gas
connecting or disconnecting the Connector, otherwise the
Installation
Connector may short-circuit internally or not ensure good
insulation. • Do not make any cable bends near the base of the Unit.
• Make sure that engagement side of any Connector is free of • Any bends made must have a minimum radius of 36 mm.
metal dust or power.
• Do not use pliers to tighten mounting the thread bracket,
otherwise the thread bracket may be damaged. Be sure to
tighten each thread bracket by hand within a torque of
0.2 N·m. If the thread bracket is not tightened securely, the
Connector may not maintain its proper degree of protection
or the thread bracket may fall off due to vibration.
• When you tighten or loosen a lock nut, hold onto only the
lock nut.
If you hold onto the cover or cable, excessive rotational
force will be applied to the Connector and may damage it.
• Fully insert S8 snap-in models until the Connectors are
hidden by the metal casing of the opposite parts, otherwise
the Connectors will not maintain their proper degree of
protection or the thread brackets may become loose due to
vibration.

121
 Easy-wire Connectors for Industrial Components

XN2
Easy-wire Connectors with
e -CON* Specifications; Ideal for
Connecting Sensors.
• Use industry-proven spring clamps for wiring.
• No special tools required for easy wiring.
• Rewiring (repairing) is possible.
• Each Connector accepts any wire size from
AWG28 (0.08 mm2) to AWG20 (0.5 mm2).
(External sheath diameter: 1.5 mm max.)
Note: *E-con specifications are currently being promoted for standardization by
manufacturers of FA components and connectors. Connector specifications are
disclosed only for the mating portions.

RoHS Compliant

Wiring Configuration Example

Connecting to FA Components
XN2A · FA components with e-CON connectors

Sensor with prewired cable

Linking cables XN2A · Original Controller PCBs

XN2D

XN2A XN2B

· FA components that connect

via terminal blocks

Ordering Information
Single-socket PCB Socket Four-socket PCB Socket
Type Cable Plug Connector Cable Socket Connector
Connector Connector

Appear-
ance

No. of
Model
contacts
3 XN2A-1370 — XN2D-1371 —
4 XN2A-1470 XN2B-1470 XN2D-1471 XN2D-4471
5 XN2A-1570 — XN2D-1571 —
6 XN2A-1670 — XN2D-1671 —
8 XN2A-1870 — XN2D-1871 —

122
 XN2
Ratings and Specifications Materials and Finish

3 A/pole (Using AWG20 wire) Item Cable type PCB type

2 A/pole (Using AWG22 wire)
Rated current Case Black PBT resin (UL94V-0)
1 A/pole (Using AWG24 wire)
0.5 A/pole (Using AWG26 or 28 wire) Black PBT resin
Cover —
(UL94V-0)
Rated voltage 32 VDC
Transparent PC resin
30 mΩ max. (20 mVDC max., 100 mA Base —
Contact resistance *1 (UL94V-0)
max.)
PA resin (UL94V-0)/
Insulation resistance 1000 MΩ min. (at 500 VDC) Lever —
natural (white)
1,000 VAC for 60 s
Dielectric strength Phosphor bronze/Underplating: Nickel (1.5 to 3.0 μm)
(leakage current: 1 mA max.)
Contact Contacts: Gold (0.2 μm min.)
Insertion tolerance 50 times Terminals: Tin plating (1.0 μm min.)
Ambient temperature *2 Operating: −30°C to 75°C Spring Stainless steel —
0.08 mm2 (AWG28) to 0.5mm2 (AWG20) Copper alloy/nickel base
Pin clamp —
Applicable wires *3 The external diameter of the cable with tin-alloy plating
sheath is 1.5 mm max.
*1. This value is the contact resistance of the connector.
*2. The temperature is limited, however, to the maximum operating temperature
for the cables.
*3. When using cables with a wire diameter of 0.16 mm or smaller, contact your
OMRON sales representative.

Dimensions (Unit: mm)

●Cable Plug Connector ●Cable Socket Connector ●Single-socket PCB Socket Connector
XN2A-1@70 XN2B-1470 XN2D-1@71

A
6
2 (pitch)

6.4 3.1 5.2

3.1
A 4-C1
2 (pitch)
B
8.9

3.4 3.3
15.8
6.4
6.75 13
B

5.05

12.3
(3.5) 0.2 3.3

2 (pitch)
23.2 C
D
7.5 17.6 18
(Strip
gauge)

6 C E
6 12.85
1.2 dia. (internal)
1.65 dia. (external) Applicable PCB Dimensions
1.65 1.05 (Top View) t=1.6r0.2
D
C
2 0.05 (pitch)

1.1
+0.05
1 0.10 dia.

6.4

Exterior of Single-
socket PCB Connector B
E

Dimensions Dimensions
Dimension Dimension
(mm) A B C (mm) A B C D E
No. of contacts No. of contacts
3 4.0 7.2 13.8 3 6.9 5.8 4.0 8.0 13.8
4 6.0 9.2 15.8 4 8.9 6.8 6.0 10.0 15.8
5 8.0 11.2 17.8 5 10.9 7.8 8.0 12.0 17.8
6 10.0 13.2 19.8 6 12.9 8.8 10.0 14.0 19.8
8 14.0 17.2 23.8 8 16.9 10.8 14.0 18.0 23.8

123
 XN2

●Four-socket PCB Socket Connector

XN2D-4471

25.9
19.5 Applicable PCB Dimensions (Top View) t=1.6±0.2
6.5 (pitch)
3.1 19.5±0.1
6.5±0.05 (pitch)
+0.05
2±0.05 (pitch) 1−0.10 dia.

6.75

8.9 6±0.1

9.05
1±0.05

3.2 3.2
15.8 Exterior of Four-socket
6.75 PCB Connector

13

3.3
0.2
2 (pitch) 1
6

Assembly Instructions
●Preparing the Cable (3) Insert the screwdriver into the
release slot, and gently pull Operating lever
Align the cable with the guide (white) Release slot
marked STRIP GAUGE on the side back the lever until a click is
of the Connector, strip 7 to 8 mm of heard by resetting the lever.
the cable sheath, and then twist the
wires several times. 7 to 8 mm

●Connecting the Cable to the Connector

(1) Use a flat-blade
screw-driver to push
Flat-blade screwdriver
down the operating
(4) Make sure that the following operations
lever inside the
have been performed.
operation slot until it
• Check that the operating lever is reset.
locks.
• Check that the procedure in step 2 has been
(2) Insert the wire fully to followed. (Pull gently on the cable to make
the back of the wire Operation slot sure that there is resistance, indicating that
insertion hole. Make sure that the cable sheath is inserted into the the Connectors are wired correctly.)
hole, and that the end of the wire has passed through the contact
section. ●Removing Cables from the Operating lever
Connector (white)
Contact section Cable sheath Wire
insertion hole (1) Press down on the operating lever to
lock the lever before removing the
cable.
(2) After removing the cable from the
Connector, always reset the operating
lever, except when rewiring the
Connector. The Connector can be
rewired without resetting the operating
lever.

124
 XN2
Safety Precautions

Precautions for Safe Use Precautions for Correct Use

• Do not pull on the Connectors or cables. Doing so may cause Do not use the product in atmospheres or environments that exceed
damage to the Connectors or cause the cables to disconnect. product ratings.
• Install the Connectors in a location where they will not be stepped ●Wiring
on, to prevent disconnection of the cables or damage to the
• Insert one wire into each insertion hole. Inserting two or more wires
Connectors. If the Connectors have to be installed in such a
into a single hole may cause unexpected problems.
location, use a protective cover. • Make sure that no power is being supplied to a Connector before
• Make sure that the Connectors are mated in the correct direction.
wiring, inserting, or removing the Connector. Doing so may result in
Mating the Connectors incorrectly will damage to the Connectors.
electric shock.
• Do not use the Connectors if the lock lever is bent or broken. Doing • Follow the wiring diagrams for the device being used when wiring
so may cause the Connector to become loose or the device to
the cables.
malfunction.
• Strip the cables according to the instructions in the applicable
• Before mounting Connectors to a PCB, make sure that the operation manual, making sure not to damage the wires.
Connectors are positioned in the correct direction.
• Do not use a screwdriver with a tip larger than the specified width
• Before bending a cable to connect it to a Connector, check the
when wiring the Connectors.
bending specifications of the cable to be used. • Make sure short-circuits are not created, e.g., by protruding wires.
• Do not exceed the rated current of the cable. Always check the
●Inserting and Removing Connectors
rated current of each cable to be used.
• Do not use pliers or other tools to remove the Connectors. • When connecting or disconnecting Connectors, always hold the
• Hold the Connectors firmly by hand when handling them. Do not case of the Connector.
use excessive force to push the Connectors. Forcing the • When mating Connectors, insert the Connector fully into the back
Connectors may result in injury. of the socket, and then make sure that the Connector will not
• These Connectors do not resist water. Do not use Connectors in become loose by lightly pulling it in the opposite direction.
places where water or oil may be sprayed onto the Connectors. ●Recommended Screwdriver
• Use a flat-blade screwdriver with a tip of 2 mm max. Do not use
screwdrivers that gradually widen towards the base of the
screwdriver.
• Using other screwdrivers may cause damage to the adjacent poles.

125
 Peripheral Devices
General-purpose Peripheral Devices
Peripheral Devices for DeviceNet Communications
Ordering Information
● General-purpose Models
Product Appearance Model Specifications

Provided with 3 parallel

Cable wiring direction: Toward top
connectors with clamps
DCN1-1NC Cable lock direction: From top
(XW4G-05C1-H1-D), standard
Connector screw direction: From top
terminating resistor

Cable wiring direction: Toward side

DCN1-1C Cable screw direction: From top
Connector screw direction: From side
Provided with 3 parallel
T-branch Tap for connectors with screws
1 branch line (XW4B-05C1-H1-D), standard
terminating resistor
Cable wiring direction: Toward top
DCN1-2C Cable screw direction: From side
Connector screw direction: From top

Provided with 3 orthogonal

Cable wiring direction: Toward side
connectors with screws
DCN1-2R Cable screw direction: From top
(XW4B-05C1-V1R-D), standard
Connector screw direction: From top
terminating resistor

Provided with 5 parallel clamp

Cable wiring direction: Toward top
connectors with screws
DCN1-3NC Cable lock direction: From top
(XW4G-05C1-H1-D), standard
Connector screw direction: From top
terminating resistor

Cable wiring direction: Toward side

DCN1-3C Cable screw direction: From top
Connector screw direction: From side
Provided with 5 parallel
T-branch Tap for connectors with screws
3 branch lines (XW4B-05C1-H1-D), standard
terminating resistor
Cable wiring direction: Toward top
DCN1-4C Cable screw direction: From side
Connector screw direction: From top

Provided with 5 orthogonal clamp

Cable wiring direction: Toward side
connectors with screws
DCN1-4R Cable screw direction: From top
(XW4B-05C1-V1R-D), standard
Connector screw direction: From top
terminating resistor

Power Supply Tap DCN1-1P Tap provided with 2 connectors, standard terminating resistor, and fuse

126
 Peripheral Devices

Product Appearance Model Specifications

Parallel clamp connector with screws

XW4G-05C1-H1-D
Connector insertion and wiring both performed horizontally.

Parallel multi-branching clamp connector with screws

XW4G-05C4-TF-D
Connector insertion and wiring performed in same direction.

Parallel connector with screws

XW4B-05C1-H1-D
Connector insertion and wiring performed in same direction.

Connectors
Parallel, screw-less, multi-branching connector
XW4B-05C4-T-D
Connector insertion and wiring performed in same direction.

Parallel, multi-branching connector with screws

XW4B-05C4-TF-D
Connector insertion and wiring performed in same direction.

Orthogonal connector with screws

XW4B-05C1-V1R-D
Connector insertion and wiring performed at a right angle.

Outer diameter: 7.00 mm

Thin Length: 100 m
DCA1-5C10(-B)
Cables DCA1-5C10-B: Cable color: Blue
DeviceNet DCA1-5C10: Cable color: Gray
Standard
Cables Outer diameter: 11.6 mm
Thick Length: 100 m
DCA2-5C10(-B)
Cables DCA2-5C10-B: Cable color: Blue
DCA2-5C10: Cable color: Gray

Terminal-block
DRS1-T Resistance of 121 Ω
Terminator

127
 Peripheral Devices

● Peripheral Devices for Flat Cables

Product Appearance Model Specifications

Connector for Flat

DCN4-SF4D Connector with lock screws for crimping flat cable
Cable

Conversion Connector
Used as a set with a DCN4-TR4 when Thin Cable is branched on a branch
for Standard Thin DCN4-BR4D
line.
Cable and Flat Cable

Power Supply
Terminal Block with
Can be used to supply communications power from terminals when Flat
Terminating DCN4-TP4D
Cable is used.
Resistance for Flat
Cable
Used as a set with a DCN4-BR4 Flat Connector Plug in the following
applications.
• Extending the trunk line
Flat Connector Socket DCN4-TR4 • T-branching the trunk line into branch lines
Used alone in the following applications.
• Connecting a DCN4-TM4 Terminating Resistor to the trunk line

Used as a set with a DCN4-TR4 Flat Connector Socket in the following

applications.
Flat Connector Plug DCN4-BR4
• Extending the trunk line
• T-branching the trunk line into branch lines

Connector terminating resistor for flat cable. Attached to the DCN4-TR4 Flat
Terminating Resistor DCN4-TM4
Connector Socket at the end of the trunk line.

Four-core flat cable (UL 2555)

Flat Cable DCA4-4F10 Length: 100 m
Conductor diameters: 0.75 mm2 x 2, 0.5 mm2 x 2

Simple Manual Crimp Crimping tool for DCN4-TR4 Flat Connector Socket or DCN4-BR4 Flat
DWT-A01
Tool Connector Plug.

Specifications
● General-purpose Models (T-branch Taps)
Between main lines: 8 A (power supply line) and 2 A
(signal line)
Rated current
Between main and branch lines: 3 A (power supply line)
and 1 A (signal line)
Insulation resistance 100 MΩ min. (at 500 VDC)
Dielectric strength 500 VAC for 1 min, leakage current: 1 mA max.
Ambient operating
0°C to 55°C
temperature

128
 Peripheral Devices
Dimensions (Unit: mm)

● General-purpose Models

T-branch Tap for 1 branch line 74.5

Internal Circuit
DCN1-1NC 67.5
TRUNK TRUNK
20 20
(With Three Branching LINE 1 LINE
5 5 5 Terminator
Connectors) connection
4 4 4
45 14 3 3 3
2 2 2
1 1 1

46 Terminal No. Name

30.9 1 V-
20.5
2 CAN L
Two, 3 DRAIN
3.5±0.1 dia.
Mounting Dimensions or M3 4 CAN H
5 V+
14.15±0.1

74.5±0.1

T-branch Tap for 1 branch line 97

Internal Circuit
Main line Main line
DCN1-1C 90
CN1 CN2
(With Three Branching Note 5 4 3 2 1 5 4 3 2 1

Connectors) 15.5

45
4
2
15.5
CN4
1 2 3 4 5
7 CN3
Socket for terminator connection
Branch line

31.27 Terminal No. Name

20.5
1 V-
Two,
3.5 dia. 2 CAN L
Mounting Dimensions or M3
3 DRAIN
4 CAN H
14±0.3
5 V+
97±0.3

Note: When connecting a branch line to the main line, connect the main line to the connector
marked with an asterisk because the resistance between the asterisks is minimal.

T-branch Tap for 3 branch lines 97

Internal Circuit
DCN1-3NC 90
TRUNK TRUNK
17 17 17 17
(With Five Branching 2.3
LINE 1 2 3 LINE
5 5 5 5 5 Terminator
Connectors) connection
4 4 4 4 4
3 3 3 3 3
45 14
2 2 2 2 2
1 1 1 1 1

Terminal No. Name

46
1 V-
30.9
20.5 2 CAN L
3 DRAIN
Two,
3.5±0.1 dia. 4 CAN H
Mounting Dimensions or M3
5 V+

14±0.1

97±0.1

129
 Peripheral Devices

T-branch Tap for 3 branch lines Internal Circuit

142 Main line Main line
DCN1-3C 135 Socket for CN1 CN2
terminator
(With Five Branching Note
5 4 3 2 1 5 4 3 2 1
4
CN6

Connectors) 2

15.5

45

15.5 1 2 3 4 5 1 2 3 4 5 1 2 3 4 5
CN3 CN4 CN5
7
Branch line Branch line Branch line

Terminal No. Name

31.27
20.5 1 V-
Two, 2 CAN L
3.5 dia.
Mounting Dimensions or M3 3 DRAIN
4 CAN H
14±0.3 5 V+

142±0.3

Note: When connecting a branch line to the main line, connect the main line to the connector
marked with an asterisk because the resistance between the asterisked portion is minimal.

Power Supply Tap 126.5 Internal Circuit

DCN1-1P 119.5
112.5
CN1
V− L S H V+
(With Two Branching F1
15.5
Connectors)

S
V+ V−
45
Two, 3.5 dia.
CN4 CN3
15.5
F2
V+' H' S' L' V−'
Socket for terminator Fuse CN2
Terminal block on
connection Connectors on Cable side power supply side

Terminal No. Name

45.3
30.9 29.9 V- V-
20.5
L CAN L
Two, S DRAIN
3.5 dia.
Mounting Dimensions or M3 H CAN H
V+ V+
14±0.3

119.5±0.3

DRS1-T Mounting Dimensions

(Terminal-block Terminator)
Two, 4.2 dia. or M4

30±0.2

30±0.2 Two, 4.4 dia.

+0.1
6−0
20 max.

20±0.15
41 max. 21 max.

130
 Peripheral Devices

● Flat Cable

Connector for Flat Cable Conversion Connector for Standard Thin Cable and
DCN4-SF4D Flat Cable
30.20 DCN4-BR4D

21.3 (23)
36

8.3
18.14
1.45
9.2 9.5

11.1 12.64 20

27 38.55

Power Supply Terminal Block with Terminating Resistance

for Flat Cable
DCN4-TP4D 4.55 6

17

20.90
16.20

3 29 13.50
33.60

Flat Connector Socket Flat Connector Plug

DCN4-TR4 DCN4-BR4

22 17
21.3 (23)

17.8
8.3

13.8 9.2 9.5

9.5

20
30.7

131
 Peripheral Devices
I/O Peripheral Devices
■ I/O Connectors for Connector Terminals
●MIL Connectors
Applicable Connectors
Type Model Remarks
Flat Cable Pressure-welded Connectors XG4M-4030-T
XG5M-4032-N Corresponding to 24 AWG
Pressure-welded Socket
XG5M-4035-N Corresponding to 28 to 26 AWG
Connectors with
Loose Wires Semicover XG5S-2001
Hood Cover * XG5S-4022
* DeviceNet connectors for multi-drop wiring cannot be used with the Hood Cover.

Cable Models
Type Model Connected device Applicable models
G79-I@@-@@-D1 DRT2-ID32ML
G79-M@@-@@-D1 DRT2-MD32ML
Cable with Connectors (1:2) G79-O@@-@@-D1 G7TC/G70D/G70A DRT2-OD32ML/DRT1-OD32ML-1
G79-I@@-@@-D2 DRT2-ID32ML-1
G79-M@@-@@-D2 DRT2-MD32ML-1
Cable with Connector (1:1) XW2Z-C@@K
Cable with Loose Wires with Crimp Terminals G79-Y@00C-D1 -- All models
Cable with Loose Wires G79-A@00C-D1

Applicable Cables with Connectors

● Cables with Connectors (1-to-2 Connection)/G79-@@-@-D@
Cable length (mm)
Appearance Model
A B
500 250 G79-I50-25-D1
A
750 500 G79-I75-50-D1
500 250 G79-O50-25-D1
750 500 G79-O75-50-D1
500 250 G79-M50-25-D1
750 500 G79-M75-50-D1
(120)
500 250 G79-I50-25-D2
750 500 G79-I75-50-D2
B
Length without any bending 500 250 G79-M50-25-D2
750 500 G79-M75-50-D2

● Cables with Connectors (1-to-1 Connection)/XW2Z-C@@K

Appearance Cable length (mm) Model

250 XW2Z-C25K

500 XW2Z-C50K
L

● Cables with Crimp Terminals (at the End of Loose Wires)/G79-Y@C-D1

Appearance Cable length (mm) Model

Terminal A Terminal B 1,000 G79-Y100C-D1

Connected G79-Y200C-D1
to device
2,000

L 5,000 G79-Y500C-D1
300

● Cables with Loose Wires/G79-A@C

Appearance Cable length (mm) Model

Terminal A Terminal B
2,000 G79-A200C-D1

Connected
to device

L 5,000 G79-A500C-D1
300

132
 Peripheral Devices

■ I/O Connectors for MULTIPLE I/O TERMINALs

Applicable Connectors
Type Model Remark Connectable model
Housing 50-57-9403
16-02-0069 Corresponding to 24 to 30 AWG
Chain terminal Digital I/O Units
16-02-0086 Corresponding to 22 to 24 AWG GT1-ID16MX(-1)/GT1-OD16MX(-1)
Crimped
Molex connector 16-02-0096 Corresponding to 24 to 30 AWG
terminals Loose terminal
16-02-0102 Corresponding to 22 to 24 AWG Analog I/O Units
GT1-AD08MX/GT1-DA04MX
57036-5000 Corresponding to 22 to 26 AWG
Press-fit tool
57037-5000 Corresponding to 24to 30 AWG
Soldered terminals FCN361J024-AU
Fujitsu connector
Pressure-welded terminals FCN367J024-AU/F
(16 points)
Crimped terminals FCN363J024-AU
Soldered terminals FCN361J040-AU
Fujitsu connector Digital I/O Units
Pressure-welded terminals FCN367J040-AU/F
(32 points) GT1-ID32ML(-1)/GT1-OD32ML(-1)
Crimped terminals FCN363J040-AU
OMRON Pulg XM3A-2521 Digital I/O Units
D-sub connector Hood XM2S-2513 #4-40UNC inch screws GT1-ID16DS(-1)/GT1-OD16DS(-1)

133
 Peripheral Devices
Applicable Cables with Connectors (Fujitsu Connectors)
I/O classification Model Connectable model
XW2Z-@@@A Digital I/O Units
Digital input, 16 points
G79-@C GT1-ID16ML(-1)
XW2Z-@@@A Digital I/O Units
Digital output, 16 points
G79-@C GT1-OD16ML(-1)
XW2Z-@@@B Digital I/O Units
Digital input, 32 points
G79-I@C@ GT1-ID32ML(-1)
XW2Z-@@@B Digital I/O Units
Digital output, 32 points
G79-O@C@ GT1-OD32ML(-1)

● Cables with Connectors (1-to1 Connection)/G79-@C

For Digital Input/Output (16 Points)
Appearance Cable length (mm) Model
1,000 G79-100C
1,500 G79-150C
2,000 G79-200C
3,000 G79-300C
L 5,000 G79-500C

● Cables with Connectors (1-to-2 Connection)/G79-O@C-@, G79-I@C-@

For Digital Input/Output (32 Points)
Cable length (mm) Model
Appearance
A B Input Output
A 1,000 750 G79-I100C-75 G79-O100C-75

1,500 1,250 G79-I150C-125 G79-O150C-125

2,000 1,750 G79-I200C-175 G79-O200C-175

3,000 2,750 G79-I300C-275 G79-O300C-275

B
Length without any bending 5,000 4,750 G79-I500C-475 G79-O500C-475

For Digital Input/Output (16 Points)

Appearance Cable length (mm) Model
500 XW2Z-050A
1,000 XW2Z-100A
1,500 XW2Z-150A
2,000 XW2Z-200A
3,000 XW2Z-300A
L
5,000 XW2Z-500A

For Digital Input/Output (32 Points)

Appearance Cable length (mm) Model
500 XW2Z-050B
1,000 XW2Z-100B
1,500 XW2Z-150B
2,000 XW2Z-200B
3,000 XW2Z-300B
L
5,000 XW2Z-500B

134
 Peripheral Devices

■ I/O Connector for Programmable Slaves

Applicable Connector Terminal Conversion Units
Applicable cable Connected product Remarks
Slim type
XW2D-20G6
(with M3 screw terminals)
XW2Z-@@@A
Flat cable connectors
XW2B-20G4
(with M3 terminal screws for flat-blade screwdriver)

Applicable Cables with Connectors

● Cables with Connectors/XW2Z
For Digital Input/Output (16 Points)
Appearance Cable length (mm) Model

500 XW2Z-050A

1,000 XW2Z-100A
1,500 XW2Z-150A

2,000 XW2Z-200A
L 3,000 XW2Z-300A

5,000 XW2Z-500A

135
 Peripheral Devices
Peripheral Devices for Environment-resistive Slaves
Peripheral Devices for DeviceNet Communications
Ordering Information
● Environment-resistive Connection Products (for Thin Cable, M12 Micro Connectors)
Product Appearance Model Specifications

Sealed Assembling-type
XS2G-D5S7 For communications (plug)
Connector (male)

Sealed Assembling-type
XS2C-D5S7 For communications (socket)
Connector (female)

Sealed T-branch Connector DCN2-1 For 1 branch line

DRS2-1 Plug
Sealed Connector with
Terminating Resistor
DRS2-2 Socket

DCA1-5CNC5W1 Length (L): 0.5 m

DCA1-5CN01W1 Length (L): 1m
DCA1-5CN02W1 Length (L): 2m
Cable with connectors on both ends
L DCA1-5CN03W1 Length (L): 3m
DCA1-5CN05W1 Length (L): 5m
DCA1-5CN10W1 Length (L): 10 m
DCA1-5CNC5F1 Length (L): 0.5 m
DCA1-5CN01F1 Length (L): 1m

Cables with Sealed DCA1-5CN02F1 Length (L): 2m

Cable with connector on one end (socket)
Connectors L 50 mm DCA1-5CN03F1 Length (L): 3m
DCA1-5CN05F1 Length (L): 5m
DCA1-5CN10F1 Length (L): 10 m
DCA1-5CNC5H1 Length (L): 0.5 m
DCA1-5CN01H1 Length (L): 1m
DCA1-5CN02H1 Length (L): 2m
Cable with connector on one end (plug)
L 50 mm DCA1-5CN03H1 Length (L): 3m
DCA1-5CN05H1 Length (L): 5m
DCA1-5CN10H1 Length (L): 10 m

DCA1-5CNC5P1 Panel-mounting connector (socket) with 0.5-m cable

Shielded Panel-mounting
Connectors (female)

XS2P-D522-2 Panel-mounting connector socket

DCA1-5CNC5M1 Panel-mounting connector (plug) with 0.5-m cable

Shielded Panel-mounting
Connectors (male)

XS2M-D524-4 Panel-mounting connector (plug) with solder-cup terminals

Waterproof cover (for

XS2Z-22
socket)

Used to cover an unused connector section

Dust cover (for socket) XS2Z-15

136
 Peripheral Devices

● Environment-resistive Models (for Thin Wires and M12 Micro Connectors)

Product Appearance Model Specifications

Sealed T-branch Connector DCN2-1S For 1 branch line

DRS2-1S Plug
Sealed Assembling type
Connector (female)
DRS2-2S Socket

DCA1-5CSC5W1 Length (L): 0.5 m

DCA1-5CS01W1 Length (L): 1m
DCA1-5CS02W1 Length (L): 2m
Cable with connectors on both ends
L DCA1-5CS03W1 Length (L): 3m
DCA1-5CS05W1 Length (L): 5m
DCA1-5CS10W1 Length (L): 10 m
DCA1-5CSC5F1 Length (L): 0.5 m
DCA1-5CS01F1 Length (L): 1m

Connectors with Shielded DCA1-5CS02F1 Length (L): 2m

Cable with connector on one end (socket)
Cables L 50 mm DCA1-5CS03F1 Length (L): 3m
DCA1-5CS05F1 Length (L): 5m
DCA1-5CS10F1 Length (L): 10 m
DCA1-5CSC5H1 Length (L): 0.5 m
DCA1-5CS01H1 Length (L): 1m
DCA1-5CS02H1 Length (L): 2m
Cable with connector on one end (plug)
L 50 mm DCA1-5CS03H1 Length (L): 3m
DCA1-5CS05H1 Length (L): 5m
DCA1-5CS10H1 Length (L): 10 m

DCN2-S4C5H1 4 ports, 0.5-m cable

Shielded Branch Relay Box

DCN2-S8C5H1 8 ports, 0.5-m cable

137
 Peripheral Devices

● Environment-resistive Models for Thick Wires with 7/8-16UN Mini Connectors

Product Appearance Model Specifications

DCN3-11 T-branch Connector

Sealed T-branch Connector

DCN3-12 T-branch Connector (Branch connector is M12.)

Sealed Connector with

DRS3-1 Plug
Terminating Resistor

DCA2-5CN01W1 Length (L): 1 m

DCA2-5CN02W1 Length (L): 2 m
Cable with connectors on both ends
L DCA2-5CN05W1 Length (L): 5 m
DCA2-5CN10W1 Length (L): 10 m
DCA2-5CN01F1 Length (L): 1 m
DCA2-5CN02F1 Length (L): 2 m
50 Cable with connector on one end (socket)
L mm DCA2-5CN05F1 Length (L): 5 m

Cables with Sealed DCA2-5CN10F1 Length (L): 10 m

Connectors DCA2-5CN01H1 Length (L): 1 m
DCA2-5CN02H1 Length (L): 2 m
50 Cable with connector on one end (plug)
L mm DCA2-5CN05H1 Length (L): 5 m
DCA2-5CN10H1 Length (L): 10 m
DCA1-5CN01W5 Length (L): 1 m
DCA1-5CN02W5 Length (L): 2 m Cable with connectors on both ends
Thin cable
L DCA1-5CN05W5 Length (L): 5 m M12 socket
DCA1-5CN10W5 Length (L): 10 m

Panel-mounting Connector
DCA2-5CNC5P1 Panel-mounting connector (socket) with 0.5-m cable
(female)

Panel-mounting Connector
DCA2-5CNC5M1 Panel-mounting connector (plug) with 0.5-m cable
(male)

Panel-mounting Connector Panel-mounting connector (plug)

XS4M-D521-1
(male) DIP terminals

Waterproof Cap (for Plug) - XS4Z-11

Waterproof Cap (for Used to cover an unused connector section.
- XS4Z-12
Socket)

138
 Peripheral Devices
Specifications
● Environment-resistive Connection Products (for Thin Cable, M12 Micro Connectors)
Type Connectors with Terminating
Connectors with Cables T-branch Connector Assembling-type Connector
Resistor
DCA1-5CN@@@1 DCN2-1 XS2@-D5S7
Item DRS2-@
Rated current 3A
Rated voltage 125 VDC
Contact resistance
40 mΩ max. (at 20 mVDC max. and 100 mA max.)
(connector)
Insulation resistance 1,000 MΩ min. (at 500 VDC)
Dielectric strength
1,500 VAC for 60 seconds (leakage current: 1 mA max.)
(connector)
Ambient operating
-20°C to 65°C
temperature
Storage temperature
-25°C to 70°C
range
Degree of protection IEC IP67
Insertion durability 200 times
Cable strength 98 N for 15 s --
No current interruptions of more than 1 µs while performing simple vibrations at either 10 to 500 Hz with 1.52-mm full amplitude or at acceleration
Vibration resistance
100 m/s2, whichever is smaller

● Environment-resistive Models (for Thin Wires and M12 Micro Connectors)

Type Connectors with Terminating
Connectors with Cables T-branch Connector Branch Relay Box
Resistor
DCA1-5CS@@@1 DCN2-1S DCN2-S@C5H
Item DRS2-@S
Rated current 3A
Rated voltage 125 VDC
Contact resistance
40 mΩ max. (at 20 mVDC max. and 100 mA max.)
(connector)
Insulation resistance 1,000 MΩ min. (at 500 VDC)
Dielectric strength
1,500 VAC for 60 seconds (leakage current: 1 mA max.) 1,000 VAC for 60 seconds
(connector)
Ambient operating
-20°C to 65°C
temperature
Storage temperature
-25°C to 70°C
range
Degree of protection IEC IP67
Insertion durability 200 times
Cable strength 98 N for 15 s --
No current interruptions of more than 1 µs while performing simple vibrations at either 10 to 500 Hz with 1.52-mm full amplitude or at acceleration
Vibration resistance
100 m/s2, whichever is smaller
Lock strength Pulling: 100 N/15 s, Rotating: 1 N·m/15 s
Lock force 0.1 to 0.25 N·m

● Environment-resistive Models for Thick Wires with 7/8-16UN Mini Connectors

Type Connectors with Connectors with T-branch T-branch Connectors with Panel Mounting Panel Mounting
Thick Cables Thin Cables Connector Connector Terminating Resistor Connector Connector
Item DCA2-5CN@@@1 DCA1-5CN@@W5 DCN3-11 DCN3-12 DRS3-1 DCA2-5CNC5P1 XS4M-D521-1
Rated current 8A 3A 8A 3A* 8A
Rated voltage 125 VDC
Contact resistance
30 mΩ max. (at 20 mVDC max. and 100 mA max.)
(connector)
Insulation resistance 1,000 MΩ min. (at 500 VDC)
Dielectric strength
1,500 VAC for 60 seconds (leakage current: 1 mA max.)
(connector)
Ambient operating
-20°C to 65°C
temperature
Storage temperature
-25°C to 70°C
range
Degree of protection IEC IP67
Insertion durability 200 times
Cable strength 98 N for 15 s -- 98 N for 15 s --
No current interruptions of more than 1 µs while performing simple vibrations at either 10 to 500 Hz with 1.52-mm full amplitude or at acceleration 100
Vibration resistance
m/s2, whichever is smaller

* The rated current between thick wires is 8 A.

139
 Peripheral Devices
Dimensions
● Environment-resistive Connection Products (for Thin Cable, M12 Micro Connectors)

Cables with Connectors on Both Ends Wiring

DCA1-5CN@@W1 Terminal No. Color Name

1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

L (cable length)

2 1 44.7 3 4

5 5

3 4 2 1
M12 M12

Cables with Connector on Single End (Socket) Wiring

DCA1-5CN@@F1 Terminal No. Color Name

1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

L (cable length)

1 2 40.7

4 3
M12 50

Cables with Connector on Single End (Plug) Wiring

DCA1-5CN@@H1 Terminal No. Color Name

1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

L (cable length)

2 1 44.7

3 4
50
M12

T-branch Connector Connectors with Terminating Resistance

DCN2-1 Connections Diagram Wiring DRS2-1 (Plug) Wiring
Plug CN0 (IN) Socket CN2 (OUT) Terminal No. Name DRS2-2 (Socket) Terminal No. Name
1 1
2 2
1 SHIELD 1 DRAIN : NC
3 3 2 V+ 2 V+ : NC
4 4
5 5 3 V- 3 V- : NC
4 CAN H 4 CAN H : 121 Ω
1 2 3 4 5 5 CAN L 5 CAN L :
Socket CN1 (OUT)
Note: Terminating resistance (121 Ω) is
connected between terminals 4
(56) and 5.
4.5 dia.
17.7 24.7 13.6
12 8 dia. (Countersinking: 2)
44.7
5 4 4 5
2 1
10
32.1
8.5 13.6
14.9 dia. dia. dia.
3 CN0 CN2 3
1 5
1
2 2
13.6 CN1 3 4

1 M12
4 2

18
Note: The diagram shows the DRS2-1 (plug).

3 5

140
 Peripheral Devices

Panel-mounting Connector (Socket) with 0.5 m Cable

Wiring
DCA1-5CNC5P1
Terminal No. Color Name
1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

M16 nut Rubber bushing

Heat-shrinking tube
2
1
5

3
4
XS2P-D522-2 500 50

Panel-mounting Connector (Socket), Solder-cup Terminals

XS2P-D522-2
M16 nut M16 × 1 Panel Cutout Dimensions
7 3 1.5 17
2 2 16 dia.+0.3
0
7+0.2
0
1 3
5 5

14 dia.

3 1
4 4 20 dia.
M12 × 1 6.8 2.5
8.7 3
20.5 5
25.5

Panel-mounting Connector (Plug) with 0.5 m Cable

Wiring
DCA1-5CNC5M1
Terminal No. Color Name
1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

M16 nut Rubber bushing

Heat-shrinking tube
1
2
5

4
3
XS2M-D524-4 500 50

Panel-mounting Connector (Socket), Solder-cup Terminals

XS2M-D524-4
M16 nut M16 × 1 Panel Cutout Dimensions
5 dia. 3
7 Sealing rubber 17
1 M12×1 1 16 dia.+0.1 7+0.1
0
2 4 0
5 5

16 dia.

4 2
3 3 20 dia.
M12×1 1.5
1.5
6.5 8.7
18.7 3.5
4.5
27.7
5.5

141
 Peripheral Devices
● Environment-resistive Models (for Thin Wires and M12 Micro Connectors)

Cables with Connectors on Both Ends Wiring

DCA1-5CS@@W1 Terminal No. Color Name

1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

L (cable length)

2 1 44.7 3 4

5 5

3 4 2 1
M12 M12

Cables with Connector on Single End (Socket) Wiring

DCA1-5CS@@F1 Terminal No. Color Name

1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

L (cable length)

1 2 40.7

4 3
M12 50+20
−10

Cables with Connector on Single End (Plug) Wiring

DCA1-5CS@@H1 Terminal No. Color Name

1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L

L (cable length)

2 1 44.7

3 4
50+20
−10
M12

T-branch Connector Connectors with Terminating Resistance

DCN2-1S Connections Diagram Wiring DRS2-1S (Plug) Wiring
Plug CN0 (IN) Socket CN2 (OUT) Terminal No. Name DRS2-2S (Socket) Terminal No. Name
1 1
2 2 1 SHIELD 1 DRAIN : NC
3 3 2 V+ 2 V+ : NC
4 4
5 5 3 V- 3 V- : NC
4 CAN H 4 CAN H : 121 Ω
1 2 3 4 5 5 CAN L 5 CAN L :
Socket CN1 (OUT)
Note: Terminating resistance (121 Ω) is
connected between terminals 4
(56) and 5.
4.5 dia.
17.7 24.7 13.6
12 8 dia. (Countersinking: 2)
5 4 4 5
2 1 44.7
10
32.1 8.5 13.6
14.9 dia. dia. dia.
3 CN0 CN2 3 5
1 1
2 2
3 4
13.6 CN1
M12
1
5 2

18
Note: The diagram shows the DRS2-1 (plug).
4 3

142
 Peripheral Devices

Shielded Branch Relay Box with Four Ports

DCN2-S4C5H1
73
23 5 1
4

2 1
33
5
54 27

3 4
4.5 dia. M12
4.5 dia.
4.5
9 9
27 30.5
82 500+60
−0

9
9
20
13.5

Connections Diagram Wiring

PORT 1 PORT 2 PORT 3 PORT 4
1 5
Terminal No. Color Name
1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L
5

Shielded Branch Relay Box with Eight Ports

DCN2-S8C5H1
73
23 5 1
4

2 1
33
5
54 27

3 4
M12
4.5 dia.
9 4.5
4.5
dia. 9
dia.
27 27 27 30.5
127 500+60
−0

9
9
20
13.5

Connections Diagram Wiring

PORT 1 PORT 2 PORT 3 PORT 4 PORT 5 PORT 6 PORT 7 PORT 8
1 5
Terminal No. Color Name
1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
5 Blue CAN L
5

143
 Peripheral Devices

● Environment-resistive Models for Thick Wires with 7/8-16UN Mini Connectors

Thick Cable with Connectors on Both Ends (5 Conductors for Communications)

DCA2-5CN@@W1
Wiring
L
Terminal
1 5 62.5 61.2 Color Name
5 1 No.
12 dia.
1 - DRAIN
2 Red V+
3 Black V-
2 4 26 dia. 26 dia. 4 2 4 White CAN H
3 3
5 Blue CAN L

Thick Cable with Connector Socket on One End (5 Conductors for Communications)
DCA2-5CN@@F1
Wiring
5 1 61.2
12 dia. Terminal
Color Name
No.
26 dia. 1 - DRAIN
2 Red V+
4 2 3 Black V-
3
4 White CAN H
L 50 5 Blue CAN L

Thick Cable with Connector Plug on One End (5 Conductors for Communications)
DCA2-5CN@@H1
Wiring
1 5 62.5
12 dia. Terminal
Color Name
No.
26 dia. 1 - DRAIN
2 Red V+
2
3
4 3 Black V-
4 White CAN H
L 50 5 Blue CAN L

Thin Cable with Connectors on Both Ends (5 Conductors for Communications)

DCA1-5CN@@W5
Wiring
L
Terminal
Color Name
40.7 No.
1 5 62.5 1 2
1 - DRAIN
7 dia.
2 Red V+
3 Black V-
14.9 dia. 4 White CAN H
2 4 26 dia. 4 5 3 Blue CAN L
3 5

Thin Cable with Panel-mounting Connector Socket on One End Panel Cutout Dimensions
(5 Conductors for Communications) 20 dia. 2
+0.1
0

DCA2-5CNC5P1
41 L 50
27
1.7 25
5 1 15
12 dia. 33 min.

Wiring
Terminal
Color Name
4 2 No.
3
M20 × 1.5 1 - DRAIN
2 Red V+
Note: A rubber seal and nut for panel mounting are included.
3 Black V-
4 White CAN H
5 Blue CAN L

144
 Peripheral Devices

Panel-mounting Connector (Plug) with 0.5 m Cable

DCA2-5CNC5M1
Wiring
46 500 50
4 25 5 Terminal
Color Name
15 No.
1 5 12 dia. 1 - DRAIN
2 Red V+
3 Black V-
4 White CAN H
2 4
3 (sequence pin) 5 Blue CAN L
M20 × 1.5
O-ring Note: A nut is included.

T-branch Connector (5 Conductors for Communications,

Thick Wire Branch Line)
DCN3-11 74.7

1 5 25.4 5 1

2 4 4 2
26 dia. D4N3-11
14.6
3 3
CN0 CN2 41.7

CN1
Connections Diagram Wiring
Plug CN0 (IN) Socket CN2 (OUT) Terminal No. Name
4 5 28.5
1 1 1 DRAIN
2 2 V+
2
3 3
3 V-
4 4
5 5 4 CAN H
5 CAN L
1 2 3 4 5 3 2 1
Socket CN1 (OUT)

T-branch Connector (5 Conductors for Communications,

Thin Wire Branch Line)
DCN3-12 74.7
1 5 5 1

2 4 4 2
26 dia. D4N3-12

14.6
3 3
CN0 CN2 37.6
5.5 dia.
CN1

Connections Diagram Wiring

25.4 28.5
Plug CN0 (IN) Socket CN2 (OUT) Terminal No. Name
1 1 1 DRAIN 3 4 1
2 2 V+
2
3 3
3 V-
4 4
5 5 4 CAN H
5 CAN L
1 2 3 4 5 5 2
Socket CN1 (OUT)

145
 Peripheral Devices

Connector (Plug) with Terminating Resistance Panel-mounting Connector (5 Pins for Communications)
DRS3-1 XS4M-D521-1
Wiring
Terminal No. Name
1 DRAIN : NC
2 V+ : NC
3 V- : NC
4 CAN H : 121 Ω
5 CAN L :
Note: Terminating resistance (121 Ω) is 30 M25 × 2
connected between terminals 4
and 5. 1 5

4
1.5 dia.
1 5

2 4
26 dia. 3
11
21
2 4 8.5 4.5
16
3 Panel Cutout Dimensions PCB Processing Dimensions
62.5

+0.1 9.1 dia.

25 dia. 2 0 5, 1.8 dia.

4.8

37 min.

Note: A rubber seal and nut for panel mounting are included.

146
 Peripheral Devices
I/O Peripheral Devices
Applicable Connectors
● Assembly Connector Plugs for M12 Microconnectors
Applicable cable Number of Connection method
Appearance Cable direction
diameter (mm) poles Crimping Soldering Screws
For 6 dia. Straight XS2G-D4C1 XS2G-D421 XS2G-D4S1
(5 to 6 dia.) Right-angle -- XS2G-D422 XS2G-D4S2
For 4 dia. Straight XS2G-D4C3 XS2G-D423 XS2G-D4S3
(4 to 5 dia.) Right-angle -- XS2G-D424 XS2G-D4S4
For 3 dia. Straight 4 XS2G-D4C5 XS2G-D425 XS2G-D4S5
(3 to 4 dia.) Right-angle -- XS2G-D426 XS2G-D4S6
For 7 dia.
XS2G-D4S9
(6 to 7 dia.)
Straight -- --
For 8 dia.
XS2G-D4S7
(7 to 8 dia.)

● Smart click Assembly Connector Plugs for M12 Microconnectors

Applicable cable Number of Connection method
Appearance Cable direction
diameter (mm) poles Crimping Soldering Screws
For 6 dia. Straight XS5G-D4C1 XS5G-D421 XS5G-D4S1
(5 to 6 dia.) Right-angle -- XS5G-D422 XS5G-D4S2
For 4 dia. Straight XS5G-D4C3 XS5G-D423 XS5G-D4S3
(4 to 5 dia.) Right-angle -- XS5G-D424 XS5G-D4S4
For 3 dia. Straight 4 XS5G-D4C5 XS5G-D425 XS5G-D4S5
(3 to 4 dia.) Right-angle -- XS5G-D426 XS5G-D4S6
For 7 dia.
XS5G-D4S9
(6 to 7 dia.)
Straight -- --
For 8 dia.
XS5G-D4S7
(7 to 8 dia.)

Applicable Cables with Connectors

● Cables with Connector (Socket/Plug) on Both Ends (M12 Microconnectors for Power Supply and I/O)
Number of
Appearance Cable direction Cable length (m) Screw-type Connectors Smart click Connectors
core wires
1 XS2W-D421-C81-F XS5W-D421-C81-F
Straight/Straight 2 XS2W-D421-D81-F XS5W-D421-D81-F
5 XS2W-D421-G81-F XS5W-D421-G81-F
2 XS2W-D422-D81-F XS5W-D422-D81-F
Right-angle/Right-angle
4 5 XS2W-D422-G81-F XS5W-D422-G81-F
2 XS2W-D423-D81-F XS5W-D423-D81-F
Straight/Right-angle
5 XS2W-D423-G81-F XS5W-D423-G81-F
2 XS2W-D424-D81-F XS5W-D424-D81-F
Right-angle/Straight
5 XS2W-D424-G81-F XS5W-D424-G81-F

● Cables with connector plug on One End (M12 Microconnectors for I/O)
Number of
Appearance Cable direction Cable length (m) Screw-type Connectors Smart click Connectors
core wires
3 XS2H-D421-AC0-F --
0.3
4 XS2H-D421-A80-F XS5H-D421-A80-F
Straight
3 XS2H-D421-CC0-F --
1
4 XS2H-D421-C80-F XS5H-D421-C80-F

● Plugs and Sockets on Y-shaped Joints (M12 Microconnectors for I/O)

DC models
Appearance Cable Connector
Cable length (m) Screw-type Connectors Smart click Connectors
0.5 XS2R-D426-B11-F XS5R-D426-B11-F
1 XS2R-D426-C11-F XS5R-D426-C11-F
Connectors on both ends
2 XS2R-D426-D11-F XS5R-D426-D11-F
With cable XS2R-D426-E11-F XS5R-D426-E11-F
3
2 XS2R-D426-D10-F XS5R-D426-D10-F
Connector on one end
5 XS2R-D426-G10-F XS5R-D426-G10-F

Without cable Connectors on both ends -- XS2R-D426-1 XS5R-D426-1

Note: Use is supported only for Environment-resistive Terminals (DRT2-@D16C(L)(-1)).

● Connector Cover for M12 Microconnectors

Appearance Product Model Application

Waterproof cover (socket) XS2Z-22 For covering unused I/O connectors

147
 Peripheral Devices
Power Supply Peripheral Devices
Applicable Cables with Connectors
● Power Supply Connectors (7/8-16UN Miniconnectors)
Appearance Product Cable length L (mm) Model

1 XS4W-D421-101-A

2 XS4W-D421-102-A

L 5 XS4W-D421-105-A

10 XS4W-D421-110-A

1 XS4F-D421-101-A

2 XS4F-D421-102-A
50
L mm 5 XS4F-D421-105-A

10 XS4F-D421-110-A

1 XS4H-D421-101-A
2 XS4H-D421-102-A
50
L mm 5 XS4H-D421-105-A

10 XS4H-D421-110-A

T-branch Connector -- XS4R-D424-5

Panel mounting connector socket

-- XS4P-D421-1C5-A
Cable: 50 cm

Panel mounting connector plug

-- XS4M-D421-1
DIP terminals

- Waterproofing Cap for Plug -- XS4Z-11

- Waterproofing Cap for Socket -- XS4Z-12

148
MEMO

149
 Standard-compliant Models (As of February 2014)

International Standards Descriptions of Certification Marks

International standards consist of the IEC standards related to UL (Underwriters Laboratories Inc.)
electricity and the ISO standards related to other areas • A nonprofit organization established in 1894 by the
(e.g., machines and management.) American association of fire insurance companies.
Underwriters Laboratories (abbreviated to UL hereafter)
IEC (International Electrotechnical Commission) conducts certification testing on all kinds of electrical
• The IEC is a standardization commission founded in 1906 to promote products. In many U.S. cities and states, UL certification is
unification and coordination of international standards relating to electricity. egally required on all electrical items sold. To obtain UL
It is headquartered in Geneva, Switzerland. certification on an electrical product, all major internal
• Based on reports from member nations on the latest science technologies in components also require UL certification.
those nations, IEC standards are issued as technological standards relating • UL offers two classifications of certification, the listing mark
to electricity. Established international safety standards provided by various and the recognition mark. A Listing Mark constitutes the
countries and accepted worldwide are based on IEC standards. entire certification of a product. Products display the Listing
• The IEC standards committees includes the CISPR (International Special Mark shown below. The Recognition Mark applies to the
Committee on Radio Interference) that makes standards for EMC components used in a product, and therefore constitutes a
(Electromagnetic Compatibility). more conditional approval of a product. Recognized
• To simplify certification procedures for electrical devices and promote products display the Recognition Mark shown at the left.
smooth international trade, there is an international scheme called CB Use of the Recognition Mark is required only for specified
Scheme (Certification Body Scheme), which is authorized by IEC standards. parts (such as basic switches).(From 2013, the UL Listing
Based on the CB Scheme, safety tests on electrical devices are conducted Mark shown in the middle on the left was changed to the
and certificates are issued if the devices are proved to meet IEC standards. Enhanced UL Mark shown at the top left with a new design
and name. The use of either mark will be recognized for a
ISO (International Organization for Standardization) period of ten years.)
• ISO is a standardization organization that started official activities in 1947 to The other mark is the recognition mark. Recognition
promote international standards in all areas (e.g., machines and certification is provided conditionally for parts built into other
management) except for electricity, which is covered by the IEC, by issuing devices. Products with a recognition certification bear the
ISO standards. It is headquartered in Geneva, Switzerland. mark show at the bottom on the left. Except for basic
miniature switches and other specific products, displaying
this mark is optional.

• Starting from 2013, products that are certified for listing

display the UL badge shown on the left in catalogs, in
product documents, and on packages.
(Either the UL badge or the UL listing mark can be used for
a period of 10 years.)

• Since October 1992, UL has been recognized as a CO

(council organization) and TO (test organization) by the
SCC (Standard Council of Canada). This authorizes UL to
conduct safety tests and certify products conforming to
Canadian standards. The above marks are UL marks for
products certifying that the products meet Canadian
standards.

Marks for Marks for US

Marks for US
Canada and Canada

LISTING
MARKS

RECOGNITION
MARKS

CSA (Canadian Standards Association)

• This association descended from a nonprofit, non-
government standardization organization established in
1919. In addition to industrial standardization, the
association now carries out safety testing on electrical
products. Standard development: The Canadian Standards
Association Product testing and certification: CSA
International
• This process is known as "certification," and consequently, CSA-certified
equipment displays the mark shown below.

150
 Standard-compliant Models
XS2 M12 connector (screw connectins)
UL certification
Type Model page
UL cUL File No.
XS2W-D421-C81-F c c E207683 68
XS2W-D421-D81-F c c E207683 68
XS2W-D421-G81-F c c E207683 68
XS2W-D421-J81-F c c E207683 68
Sokets/Plugs XS2W-D422-D81-F c c E207683 68
Connectors on Both End XS2W-D422-G81-F c c E207683 68
XS2W-D423-D81-F c c E207683 68
XS2W-D423-G81-F c c E207683 68
XS2W-D424-D81-F c c E207683 68
XS2W-D424-G81-F c c E207683 68
XS2F-D421-CA0-F c c E207683 71
XS2F-D421-CC0-F c c E207683 71
XS2F-D421-C80-F c c E207683 71
XS2F-D421-DA0-F c c E207683 71
XS2F-D421-DC0-F c c E207683 71
XS2F-D421-D80-F c c E207683 71
XS2F-D421-GA0-F c c E207683 71
XS2F-D421-GA0-F c c E207683 71
XS2F-D421-GC0-F c c E207683 71
XS2F-D421-G80-F c c E207683 71
XS2F-D421-JA0-F c c E207683 71
XS2F-D421-JC0-F c c E207683 71
XS2F-D421-J80-F c c E207683 71
XS2F-D422-CA0-F c c E207683 71
XS2F-D422-CC0-F c c E207683 71
XS2F-D422-C80-F c c E207683 71
XS2F-D422-DA0-F c c E207683 71
XS2F-D422-DC0-F c c E207683 71
XS2F-D422-D80-F c c E207683 71
XS2F-D422-GA0-F c c E207683 71
XS2F-D422-GC0-F c c E207683 71
Sokets
XS2F-D422-G80-F c c E207683 71
Plugs on One End
XS2F-D422-JA0-F c c E207683 71
XS2F-D422-JC0-F c c E207683 71
XS2F-D422-J80-F c c E207683 71
XS2F-A421-CB0-F c c E207683 71
XS2F-A421-C90-F c c E207683 71
XS2F-A421-DB0-F c c E207683 71
XS2F-A421-D90-F c c E207683 71
XS2F-A421-GB0-F c c E207683 71
XS2F-A421-G90-F c c E207683 71
XS2F-A421-JB0-F c c E207683 71
XS2F-A421-J90-F c c E207683 71
XS2F-A422-CB0-F c c E207683 71
XS2F-A422-DB0-F c c E207683 71
XS2F-A422-GB0-F c c E207683 71
XS2F-A422-JB0-F c c E207683 71
XS2H-D821-AH0-C c c E207683 77
XS2H-D821-CH0-C c c E207683 77
XS2F-D821-DH0-C c c E207683 77
XS2F-D821-GH0-C c c E207683 77
XS2W-D821-DH1-C c c E207683 77
XS2W-D821-GH1-C c c E207683 77
XS2F-M12PVC3A2MPLED c c E207683 74
XS2F-M12PVC3A5MPLED c c E207683 74
XS2F-M12PVC3A10MPLED c c E207683 74
XS2F-M12PVC3A2MNLED c c E207683 74
Sokets on One Cable End
XS2F-M12PVC3A5MNLED c c E207683 74
with Indicator
XS2F-M12PVC3A10MNLED c c E207683 74
XS2F-M12PVC4A2MPLED c c E207683 74
XS2F-M12PVC4A5MPLED c c E207683 74
XS2F-M12PVC4A10MPLED c c E207683 74
Note: Only products that are certified for standards are listed here.

151
 Standard-compliant Models
UL certification
Type Model page
UL cUL File No.
XS2H-D421-AA0-F c c E207683 76
XS2H-D421-AC0-F c c E207683 76
XS2H-D421-A80-F c c E207683 76
XS2H-D421-CA0-F c c E207683 76
XS2H-D421-CC0-F c c E207683 76
Plug on One End
XS2H-D421-C80-F c c E207683 76
XS2H-A421-AB0-F c c E207683 76
XS2H-A421-A90-F c c E207683 76
XS2H-A421-CB0-F c c E207683 76
XS2H-A421-C90-F c c E207683 76
XS2G-D4C1 c c E207683 79
XS2G-D4C3 c c E207683 79
XS2G-D4C5 c c E207683 79
Crimping Plug Assemblies
XS2G-A4C1 c c E207683 79
XS2G-A4C3 c c E207683 79
XS2G-A4C5 c c E207683 79
XS2G-D421 c c E207683 79
XS2G-D422 c c E207683 79
XS2G-D423 c c E207683 79
XS2G-D424 c c E207683 79
Soldering Plug Assemblies XS2G-D425 c c E207683 79
XS2G-D426 c c E207683 79
XS2G-A421 c c E207683 79
XS2G-A423 c c E207683 79
XS2G-A425 c c E207683 79
XS2C-D4C1 c c E207683 80
XS2C-D4C2 c c E207683 80
XS2C-D4C3 c c E207683 80
XS2C-D4C4 c c E207683 80
XS2C-D4C5 c c E207683 80
XS2C-D4C6 c c E207683 80
Crimping Socket Assemblies
XS2C-A4C1 c c E207683 80
XS2C-A4C2 c c E207683 80
XS2C-A4C3 c c E207683 80
XS2C-A4C4 c c E207683 80
XS2C-A4C5 c c E207683 80
XS2C-A4C6 c c E207683 80
XS2C-D421 c c E207683 80
XS2C-D422 c c E207683 80
XS2C-D423 c c E207683 80
XS2C-D424 c c E207683 80
XS2C-D425 c c E207683 80
XS2C-D426 c c E207683 80
Soldering Socket Assemblies
XS2C-A421 c c E207683 80
XS2C-A422 c c E207683 80
XS2C-A423 c c E207683 80
XS2C-A424 c c E207683 80
XS2C-A425 c c E207683 80
XS2C-A426 c c E207683 80
XS2R-D426-B11-F c c E207683 84
XS2R-D426-C11-F c c E207683 84
XS2R-D426-D11-F c c E207683 84
XS2R-D426-E11-F c c E207683 84
Y-Joints XS2R-D426-D10-F c c E207683 84
Plug/Socket Connectors XS2R-D426-G10-F c c E207683 84
XS2R-D426-1 c c E207683 84
XS2R-D426-5 c c E207683 84
XS2R-D426-81 c c E207683 84
XS2R-D426-82 c c E207683 84
Note: Only products that are certified for standards are listed here.

152
 Standard-compliant Models
XS5 M12 Connectros (Smartclick)
UL certification
Type Model page
UL cUL File No.
XS5W-D421-C81-F c c E207683 35
XS5W-D421-D81-F c c E207683 35
XS5W-D421-E81-F c c E207683 35
XS5W-D421-G81-F c c E207683 35
XS5W-D421-J81-F c c E207683 35
Plug on One End and
XS5W-D422-D81-F c c E207683 35
Socket on Other End
XS5W-D422-G81-F c c E207683 35
XS5W-D423-D81-F c c E207683 35
XS5W-D423-G81-F c c E207683 35
XS5W-D424-D81-F c c E207683 35
XS5W-D424-G81-F c c E207683 35
XS5F-D421-C80-F c c E207683 36
XS5F-D421-D80-F c c E207683 36
XS5F-D421-E80-F c c E207683 36
XS5F-D421-G80-F c c E207683 36
XS5F-D421-J80-F c c E207683 36
Soket on One End
XS5F-D422-C80-F c c E207683 36
XS5F-D422-D80-F c c E207683 36
XS5F-D422-E80-F c c E207683 36
XS5F-D422-G80-F c c E207683 36
XS5F-D422-J80-F c c E207683 36
XS5H-D421-A80-F c c E207683 37
XS5H-D421-C80-F c c E207683 37
XS5H-D421-D80-F c c E207683 37
XS5H-D421-G80-F c c E207683 37
Plug on One End
XS5H-D422-A80-F c c E207683 37
XS5H-D422-C80-F c c E207683 37
XS5H-D422-D80-F c c E207683 37
XS5H-D422-G80-F c c E207683 37
XS5G-D4C1 c c E207683 40
Crimping Plug Assemblies XS5G-D4C3 c c E207683 40
XS5G-D4C5 c c E207683 40
XS5G-D421 c c E207683 40
XS5G-D422 c c E207683 40
XS5G-D423 c c E207683 40
Soldering Plug Assemblies
XS5G-D424 c c E207683 40
XS5G-D425 c c E207683 40
XS5G-D426 c c E207683 40
XS5G-D4S1 c c E207683 40
XS5G-D4S2 c c E207683 40
XS5G-D4S3 c c E207683 40
XS5G-D4S4 c c E207683 40
Screw-on Plug Assemblies
XS5G-D4S5 c c E207683 40
XS5G-D4S6 c c E207683 40
XS5G-D4S7 c c E207683 40
XS5G-D4S9 c c E207683 40
XS5C-D4C1 c c E207683 43
XS5C-D4C2 c c E207683 43
Crimping Socket Assemblies XS5C-D4C3 c c E207683 43
XS5C-D4C4 c c E207683 43
XS5C-D4C5 c c E207683 43
XS5C-D421 c c E207683 43
XS5C-D422 c c E207683 43
XS5C-D423 c c E207683 43
Soldering Socket Assemblies
XS5C-D424 c c E207683 43
XS5C-D425 c c E207683 43
XS5C-D426 c c E207683 43
Note: Only products that are certified for standards are listed here.

153
 Standard-compliant Models

UL certification
Type Model page
UL cUL File No.
XS5C-D4S1 c c E207683 43
XS5C-D4S2 c c E207683 43
XS5C-D4S3 c c E207683 43
XS5C-D4S4 c c E207683 43
Screw-on Socket Assemblies
XS5C-D4S5 c c E207683 43
XS5C-D4S6 c c E207683 43
XS5C-D4S7 c c E207683 43
XS5C-D4S9 c c E207683 43
XS5R-D426-B11-F c c E207683 45
XS5R-D426-C11-F c c E207683 45
XS5R-D426-D11-F c c E207683 45
Y-Joints XS5R-D426-E11-F c c E207683 45
Plug/Socket Connectors XS5R-D426-D10-F c c E207683 45
XS5R-D426-G10-F c c E207683 45
XS5R-D426-1 c c E207683 45
XS5R-D426-5 c c E207683 45
XS5M-D426-5 c c E207683 47
Panel-mounting Plugs
XS5M-D427-5 c c E207683 47
XS5P-D426-5 c c E207683 46
Panel-mounting Sockets
XS5P-D427-5 c c E207683 46
Note: Only products that are certified for standards are listed here.

XS5 Industrial Ethernet Connectors

UL certification
Type Model page
UL cUL File No.
XS5H-T421-BM0-K c c E207683 21
XS5H-T421-CM0-K c c E207683 21
XS5H-T421-DM0-K c c E207683 21
Cable with Plug on One End
XS5H-T421-EM0-K c c E207683 21
(M12 Straight)
XS5H-T421-GM0-K c c E207683 21
XS5H-T421-JM0-K c c E207683 21
XS5H-T421-KM0-K c c E207683 21
XS5W-T421-BME-K c c E207683 21
XS5W-T421-CME-K c c E207683 21
Cable with Plug on One End and XS5W-T421-DME-K c c E207683 21
Socket on Other End XS5W-T421-EME-K c c E207683 21
(M12 Straight/RJ45) XS5W-T421-GME-K c c E207683 21
XS5W-T421-JME-K c c E207683 21
XS5W-T421-KME-K c c E207683 21
Note: Only products that are certified for standards are listed here.

154
 Standard-compliant Models
DeviceNet
UL certification
Type Model page
UL cUL File No.
XW4G-05C1-H1-D c c E245101 127
XW4B-05C1-H1-D c c E245101 127
Connectors XW4B-05C4-T-D c c E245101 127
XW4B-05C4-TF-D c c E245101 127
XW4B-05C1-V1R-D c c E245101 127
Terminal-block Terminator DRS1-T c E95399 127
Sealed T-branch Connector DCN2-1 c E207683 136
DRS2-1 c E207683 136
DRS2-2 c E207683 136
DCA1-5CNC5W1 c E207683 136
DCA1-5CN01W1 c E207683 136
DCA1-5CN02W1 c E207683 136
DCA1-5CN03W1 c E207683 136
DCA1-5CN05W1 c E207683 136
DCA1-5CN10W1 c E207683 136
DCA1-5CNC5F1 c E207683 136
DCA1-5CN01F1 c E207683 136
DCA1-5CN02F1 c E207683 136
Cables with Sealed Connectors
DCA1-5CN03F1 c E207683 136
DCA1-5CN05F1 c E207683 136
DCA1-5CN10F1 c E207683 136
DCA1-5CNC5H1 c E207683 136
DCA1-5CN01H1 c E207683 136
DCA1-5CN02H1 c E207683 136
DCA1-5CN03H1 c E207683 136
DCA1-5CN05H1 c E207683 136
DCA1-5CN10H1 c E207683 136
DCN3-11 c E207683 138
Sealed T-branch Connector
DCN3-12 c E207683 138
Sealed Connector with
DRS3-1 c E207683 138
Terminating Resistor
DCA2-5CN01W1 c E207683 138
DCA2-5CN02W1 c E207683 138
DCA2-5CN05W1 c E207683 138
DCA2-5CN10W1 c E207683 138
DCA2-5CN01F1 c E207683 138
DCA2-5CN02F1 c E207683 138
Cables with Sealed Connectors
DCA2-5CN05F1 c E207683 138
DCA2-5CN10F1 c E207683 138
DCA2-5CN01H1 c E207683 138
DCA2-5CN02H1 c E207683 138
DCA2-5CN05H1 c E207683 138
DCA2-5CN10H1 c E207683 138
Note: Only products that are certified for standards are listed here.

155
 Model Index
Connectors
Industrial

XS2W 67, 147

Ethernet

D
XS2W (8-pole) 77
DCA1-@ 127, 136, 137, 138
XS2Z-11 48, 88
DCA2-@ 127, 138
XS2Z-13 48, 88
DCA4-4F10 128
XS5/XS6

XS2Z-14 48, 88
DCN1-@ 126
XS2Z-15 48, 88, 136
DCN2-@ 136, 137
XS2Z-18 89
DCN3-@ 138
XS2Z-22 27, 62, 88, 96, 136, 147
Sensor I/O
Connector

DCN4-@ 128
XS2Z-31 48, 89
DRS1-T 127
XS3 101
DRS2-1 136
XS3F 108
DRS2-1S 137
XS3H 112
Introduction to

Connectors

DRS2-2 136
Sensor I/O

XS3M 117
DRS2-2S 137 XS3P 115
DRS3-1 138 XS3R 120
DWT-A01 128 XS3W 104
XS5

XS3Z-13 119
E XS3Z-15 119
XS4F-@ 148
XW3D

E2E 58
E2EC 59 XS4H-@ 148
E2EF 59 XS4M-D421-1 148

E2EQ 58 XS4M-D521-1 138

XS2

E2EZ 59 XS4P-D421-1C5-A 148

XS4R-D424-5 148
E2FM 58
XS4W-@ 148
E2V 59
XW3B

XS4Z-11 138, 148

E3T 57
XS4Z-22 138, 148
E3Z 56
XS5 32
E3ZM-C 56
XS3

XS5/XS6 14
XS5C 42
G XS5F 36
G79-@ 132, 134
XN2

XS5F (8-pole) 38
XS5G 39, 147
W XS5H 21, 37, 147
WLCA2 60 XS5M 47
Peripherals
DeviceNet

WLG2 60 XS5M (8-pole) 38

XS5P 22, 46
XS5R 45, 147
X
XS5U (for XS5C) 44
Communications
Standard Slaves
Peripherals for

XG4M-@ 132
XS5U (for XS5G) 41
XG5M-@ 132
XS5W 21, 34, 147
XG5S-@ 132
XS5Z-11 48, 62
I/O Peripherals
for Standard

XM2S-@ 133
Slaves

XS6G 22
XM3A-@ 133
XS6W 18
XN2 122
XW2R-@ 135
Communications

resistive Slaves
Peripherals for
Environment-

XS2 65
XW2Z-@ 132, 134, 135
XS2C (Screw-on) 82 XW3B 94
XS2C (Crimping, Soldering) 80 XW3D 61
for Environment-
resistive Slaves

XS2C-D5S7 136
I/O Peripherals

XW4B-@ 127
XS2F 69 XW4G-@ 127
XS2F (8-pole) 77 XY2F-0001 49, 89
resistive Slaves

XS2G 147
Peripherals for
Environment-
Power Supply

XY2F-0002 49, 89
XS2G (Screw-on) 81 XY2F-0003 49, 89
XS2G (Crimping, Soldering) 79 XY2F-0004 89
XS2G-D5S7 136
XS2H 75, 147
compliant
Standard-

Models

XS2H (8-pole) 77
XS2M 87
XS2M (8-pole) 77
XS2M-D524-4 136
Model Index

XS2P 83
XS2P (8-pole) 77
XS2P-D522-2 136
XS2R 84, 147
XS2U (for XS2C) 80
XS2U (for XS2G) 79

156
 MEMO

Standard- Power Supply I/O Peripherals Communications Introduction to Industrial

Peripherals for Peripherals for I/O Peripherals Communications DeviceNet Sensor I/O
Model Index compliant for Environment- for Standard Peripherals for Sensor I/O Ethernet

157
Environment- resistive Slaves Environment- Peripherals XN2 XS3 XW3B XS2 XW3D XS5 Connector XS5/XS6
Models resistive Slaves resistive Slaves Slaves Standard Slaves Connectors Connectors
 Standard- Power Supply I/O Peripherals Communications Introduction to Industrial
Peripherals for Peripherals for I/O Peripherals Communications DeviceNet Sensor I/O
Model Index compliant for Environment- for Standard Peripherals for XN2 XS3 XW3B XS2 XW3D XS5 Sensor I/O XS5/XS6 Ethernet
Environment- resistive Slaves Environment- Peripherals Connector
resistive Slaves resistive Slaves Slaves Standard Slaves Connectors Connectors
Models

158
MEMO
 Terms and Conditions Agreement
Read and understand this catalog.
Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have
any questions or comments.

Warranties.
(a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship
for a period of twelve months from the date of sale by Omron (or such other period expressed in writing
by Omron). Omron disclaims all other warranties, express or implied.
(b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT
NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE
PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL
SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE.
Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products
or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election,
to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the
non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price
of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other
claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored,
installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by
Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or
unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system
assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in
writing, are not to be construed as an amendment or addition to the above warranty.
See http://www.omron.com/global/ or contact your Omron representative for published information.

Limitation on Liability; Etc.

OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES,
LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS,
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY.
Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted.

Suitability of Use.
Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the
combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable
third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is
not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system,
or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with
respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE
QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE
OVERALL EQUIPMENT OR SYSTEM.

Programmable Products.
Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof.

Performance Data.
Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining
suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it
to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability.

Change in Specifications.
Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice
to change part numbers when published ratings or features are changed, or when significant construction changes are made.
However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be
assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to
confirm actual specifications of purchased Product.

Errors and Omissions.

Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is
assumed for clerical, typographical or proofreading errors or omissions.
OMRON Corporation Industrial Automation Company Authorized Distributor:
Tokyo, JAPAN
Contact: www.ia.omron.com
Regional Headquarters
OMRON EUROPE B.V. OMRON ELECTRONICS LLC
Wegalaan 67-69, 2132 JD Hoofddorp 2895 Greenspoint Parkway, Suite 200
The Netherlands Hoffman Estates, IL 60169 U.S.A
Tel: (31)2356-81-300/Fax: (31)2356-81-388 Tel: (1) 847-843-7900/Fax: (1) 847-843-7787

OMRON ASIA PACIFIC PTE. LTD. OMRON (CHINA) CO., LTD. © OMRON Corporation 2014 All Rights Reserved.
No. 438A Alexandra Road # 05-05/08 (Lobby 2), Room 2211, Bank of China Tower, In the interest of product improvement,
Alexandra Technopark, 200 Yin Cheng Zhong Road, specifications are subject to change without notice.
Singapore 119967 PuDong New Area, Shanghai, 200120, China Printed in Japan
Tel: (65) 6835-3011/Fax: (65) 6835-2711 Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200 Cat. No. X082-E1-01 0315 (0315)